View
42
Download
0
Category
Tags:
Preview:
DESCRIPTION
MCAS CHERRY POINT. Basic Airfield Vehicle Operator Course (AVOC). REFERENCES. FAA Handbook 7110.65 NAVAIR 00-80T-114 MCO 1500.19 AirStaO P 3710.5 ATCFacO P3722.1. PURPOSE. - PowerPoint PPT Presentation
Citation preview
MCAS CHERRY POINT
Basic Airfield Vehicle Operator Course (AVOC)
REFERENCES
1) FAA Handbook 7110.65
2) NAVAIR 00-80T-114
3) MCO 1500.19
4) AirStaO P 3710.5
5) ATCFacO P3722.1
PURPOSE
The purpose of the Basic Airfield Vehicle Operator Course (AVOC) is to ensure all individuals who operate vehicles and support equipment are properly trained so they can safely communicate and operate on MCAS Cherry Point’s Airfield.
Course Overview
Classroom
Written Exam (80% or better)
Airfield Tour
Facility that uses air/ground communications, visual signals and other devices to provide ATC services to aircraft and vehicles operating on or in the vicinity of the airfield
Control Tower
Non-Movement Area- Areas on an airfield not under the control of ATC. (aircraft parking ramps)
Vigilance is required as to not run into parked aircraft, aircraft engine starts, etc.
Non-movement
Runways, taxiways and other areas of an airport which are utilized for aircraft operations.
Approval for entry onto the movement area must be obtained from the control tower.
Airfield vehicle operators license required.
Movement Area
Operating on movement areas Never operate any vehicle on the airfield
movement areas without establishing two way communications with the control tower.
Only operate in areas authorized by the Control Tower.
Anytime you become disoriented, hold your position and ask for guidance from the Tower.
Give way to all emergency vehicles responding to an emergency.
Maintain radio discipline at all times. After receiving authorization, look both ways
before crossing a runway. Airport speed limit is 20 MPH. 5 MPH when
towing an aircraft or within parking ramps/fuel pits EXPEDITE movement on runway areas. While operating on the airfield, operate hazards
and flashing lights. During the hours of darkness, be careful to operate
headlights so not to blind pilots.
Runway- A defined rectangular area where aircraft operations are conducted (takeoffs and landings).
Duty Runway- The runway in use by ATC. Runway markings are WHITE. Runway lights are WHITE.
Runways
Runway
AV- 8 VSTOL Pads
Concrete Pad used for AV-8 vertical takeoffs and landings.
CALA
DD
FF
BB
AA
FUEL PITS
HEAVY FUEL PITS
ARM/DEARM
4
3
2
1
HELOVIP2
TACAN ASR-8
RECOVERY
VIP1
E-28E-28
E-28
E-28FRESNEL
E-5
E-5
FRESNEL
E-5
FRESNEL
E-5
FRESNEL
PAPI
PAPI
FUEL PITS
OUTBOUND
JJ
HHII
GG
EE
FPN-63
5R32L
23R14L
8080
X196 7607X200
7600
X200
8968X200
PAPI
PAPI
7100 X 200
4800 X 200
6100 X 2006
78
9
1
2
3
4
5
1011
1213
1415
TAXIWAYSTHRU
WARM-UP AREASTHRU
A L
1 4
FUEL PITS
T-LINE
A
B
C
D
E
E
F
G
H
I
KK
TAXIWAYSA & KUNLIT
CC
WASHRACK
SOUTHPAD
1500F
T
NADEPPAD
ILSCRITICAL
AREA
CONTROLTOWER
INBOUND
1500FT
CRASHCREW
HIGHPOWERRUN-UP
ILSCRITICAL
AREA
1500FT
CARRIERDECK
1500FT
SOUTHEASTPAD
COMPASS ROSE
NORTHEASTPAD
LL
Taxiway- Paved area for aircraft movement between the runway and parking area.
Taxiway markings are YELLOW.
Taxiway lights are BLUE.
Taxiways
Taxiway
CALA
D
F
B
A
ORDNANCESAFETY AREA
4
E-28E-28
E-28
E-28
PAPI
PAPI
J
I
G
E
PAPI
PAPI
A
B
C
D
E
E
F
G
H
I
K
C
VTL4(SOUTH)NADEP
PAD
BASE OPS /PASSENGERTERMINAL /
TOWER
VTL3(SOUTHEAST)
COMPASSROSE
VTL2(NORTHEAST)
L
VTL1(NORTH)H M N
AERIALPORT OFEMBARK-
ATIONLARGE
AIRCRAFTREFUELING
AREA
HANGARS
ELEV23
ELEV28
HIGH POWER
RADAR REFLECTORSON ALL RWYS
ELEV17
ELEV19
ELEV19
ELEV29
ELEV29
FIELDELEV
29
Displaced Thresholds for landing only:Departing Rwy 14R distance 8398’Departing Rwy 5L distance 8491’
RADAR REFLECTORSON ALL RUNWAYS
RECOVERY
CFRP
VMU-2
CFR RAMPK
3
2
1
Signs and Markings
Distance remaining board
Runway and Taxiway sign
Taxiway signs
Hold short line
Windsock
ILS Critical Area
Radios can be checked out for a 10 hour period from Airfield Base Operations.
The ATC Ground Controller is responsible for all movement of vehicles on the airfield movement areas.
Make requests as simple and direct as possible. The number of vehicles simultaneously operating
on the airfield can cause the FM frequency to be congested. In addition, the controllers are not just talking to vehicles, they are responsible for the entire ground movement. If the tower doesn’t answer you immediately, they may be talking to aircraft or issuing clearances on a different frequency.
Communications
Acknowledge – Let me know you have received and understand this message.
Advise intentions – Tell me what you plan to do. Affirmative – Yes. Confirm – My version is…is that correct? Correction – An error has been made in the
transmission and the correct version follows. Go ahead – State your request (never means
“proceed”).Hold – Stop where you are.
Operating terms
Hold short of … - Proceed to, but hold short of a specific point.
Negative – No, or permission not granted, or that is not correct
Proceed – You are authorized to begin or continue moving.
Read back – Repeat my message back to me. Roger – I have received all of your last
transmission. Say again – Repeat what you just said. Standby – Wait…I will get back to you. The caller
should reestablish contact if the delay is lengthy.
Unable – I can’t do it. Verify – Request confirmation of information. Wilco – I have received your message, understand
it, and will comply. Without Delay - Instruction from ATC to expedite
the movement of an aircraft or vehicle. Expedite - Term used by ATC when prompt compliance is required to avoid the development of an imminent situation.
Phraseology When operating on the airfield, use clear, concise
and correct phraseology. Know your vehicle call sign and speak clearly,
distinctly and know exactly what you want to say. Be absolutely sure you understand what the Control
Tower has said. If you are unsure of any part, hold your position and request the tower to repeat their instructions.
There are four basic steps: 1) identify who your calling and who you are, 2) wait for the tower to respond, 3) State your request and your position, and 4) read back exactly what the tower authorized you to do.
Driver - “Ground, Cherry Alpha”.
**Wait for a response**
Tower - “Cherry Alpha, Cherry Point Ground”
Driver - “Ground, Cherry Alpha is at the base of the tower, requesting permission to proceed across Runway 5 to Charlie Taxiway”.
Tower - “Cherry Alpha, Ground, proceed up to and hold short of Runway 5 abeam Charlie Taxiway”.
Driver - “Ground, Cherry Alpha is proceeding up to and will hold short of Runway 5 abeam Charlie Taxiway”.
**PROCEED**
Driver - “ Cherry Point Ground, Cherry Alpha is holding short of Runway 5”.
Phraseology Example
Tower - “Cherry Alpha proceed across Runway 5 to Charlie Taxiway”.
Driver - “Ground, Cherry Alpha is proceeding across Runway 5 to Charlie Taxiway”.
**PROCEED**
Driver - “Ground, Cherry Alpha is clear of Runway 5 on Charlie Taxiway”.
Tower – “Cherry Alpha Roger”.
* Runway incursions are the number one airfield hazard to pilots and air traffic controllers. FAA standards direct that all ATC hold short instructions SHALL be read back verbatim.
A Alpha J Juliet S SierraB Bravo K Kilo T TangoC Charlie L Lima U UniformD Delta M Mike V VictorE Echo N November W WhiskeyF Foxtrot O Oscar X X-rayG Golf P Papa Y YankeeH Hotel Q Quebec Z ZuluI India R Romeo
Phonetic Alphabet
Prior to entering the movement area:• Check your radio, re-attempt.• Get another radio.
*** Vehicles shall not enter a movement area without two way communication with the tower.
While on the movement area:• Check your radio.• Point vehicle at the tower and flash head lights.• Hold your position, tower will send out an assistance vehicle.
Lost Communications
Cross perpendicular to the runway.
Do not cut across the center mat.
Look both ways for any landing or departing aircraft.
Broadcast your intentions on Ground Control frequency in the blind. Example: “(call sign) broadcasting in the blind, crossing runway five right from the base of the tower to the PAR site.”
Cross the runway. After crossing the runway, broadcast on frequency 140.1 that you are
clear of the runway.
Closed Field Procedures
Steady Green Cleared to cross; proceed; go Steady Red Stop Flashing Red Clear/exit the runway/taxiway immediately Flashing white Return to starting point Alternating Red/Green Exercise extreme caution
Light Gun Signals
Bird Aircraft Strike Hazard (BASH)- Incidents involving collision between any of nature’s creatures and an aircraft.
BASH
Jet Blast Clip
Jet Blast- Jet engine exhaust.
Foreign Object Debris (FOD)
Foreign Object Damage (FOD) is damage to aeronautical equipment caused by an object external to that equipment.
FOD to aircraft, engines, support equipment, and other aeronautical equipment is a costly problem which cannot be overstated.
Ingestion of foreign objects by gas turbine engines accounts for the largest percentage of premature engine removals from naval aircraft. FOD presents personnel and material hazards, consumes valuable maintenance man-hours, imposes additional unscheduled workloads on both using and supporting activities, creates shortages, wastes dollars, and reduces operational readiness.
Most FOD can be attributed to poor housekeeping, facility
deterioration, improper maintenance practices or carelessness.
FOD
Vehicles transiting the aircraft operating surfaces carry the ingredients for FOD.
Tires pick up rocks and deposit them on the runways.
Mud caked on the vehicle can fall off and create a hazard.
Bolts, fasteners and other hardware are often found to be culprits in a FOD investigation.
Material carried in the back of pickup trucks or on the back of stake beds can find its way to the runway surface.
Vehicles and FOD
Stop and check your vehicle before you enter an active aircraft operating area such as a taxiway or runway.
Examine the vehicle for anything that may fall off such as caked on mud or other debris. This includes the bed.
Check your tires for material caught in the tread. Any debris found must be removed, collected and properly disposed of.
Inspect the vehicle each time you enter an active area from an inactive area.
FOD Prevention
When on the movement area, report any observed FOD to the Tower.
Routinely watch for FOD on parking ramps, turn up areas, work spaces, taxiways, test cell areas, and runways. Pick up the material and dispose of it properly.
Clean up your work area. Account for each tool, each item of support equipment, and consumable used in the repair of items on the airfield.
A washer left on a runway can easily do 1.5 million dollars in damage.
MCO 1500.19 – Currently mandates 8 consecutive hours of rest in any given 24-hour period. Limits total driving time to 10 hours on any given shift.
CREW REST
QUESTIONS?
Recommended