View
3
Download
0
Category
Preview:
Citation preview
LEDBAR 24/36/48WALL/CEILING
NOTE
Assembly instructions
rev 0.1Y503-11000
Attention: Read and understand these instructions before installing fixture. This fixture is intended for installation in accordance with the National Electric Code and local regulation. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. This equipment is guaranteed only when used as indicated in these instructions; therefore they should be kept for future reference. To prevent electrical shock, turn off power supply before carrying out any connection or maintenance operations. During installation, the LED chips may be exposed; please do not touch them to ensure proper long-term operation.
Parts Bag
The following instructions apply to both Round and Square versions of LEDBAR identically; only the round model is illustrated to simplify. The fixture can be mounted in any desired orientation.
STEP 1 Make sure you have all the elements of the fixture. Your box should contain the following parts:
Hex Key
#6 Screws (2)
Canopy plate(Round or Square)
Assembled Luminaire
End cap
STEP 2 2.1 Remove both end caps using 5/64” Hex Key (supplied) to expose mounting backplate2.2 Loosen screws (Philips #2) slightly on each end to release backplate from luminaire
2.1 2.2
STEP 3 (Optional) If mounting luminaire directly over electrical junction box, mount canopy plate to luminaire backplate using the provided #6 screws (2)
Align screw holes
#6 Screws (2)
Backplate Canopy plate
5/64”
Artemide inc.1980, New Highway, Farmingdale (NY) 11735T. +1 631 694 9292 | infousa@artemide.net | www.artemide.net
Artemide Ltd.11105, rue Renaude Lapointe, Montréal (QC) H1J 2T4
T. +1 514 323 6537 | infocanada@artemide.net | www.artemide.net1
LEDBAR 24/36/48WALL/CEILING
Assembly instructions
rev 0.1Y503-11000
“Y” Distance from center
LEDBAR 24: 8in (203mm)LEDBAR 36: 14in (356mm)LEDBAR 48: 20in (508mm)
X
4.1 Measure and mark and drill appropriate hole distance to mount backplate to wall or ceiling. Install anchors if required (not included).4.2 Pry out the knock-out opening corresponding to the installation type, to feed the wiring through
4.1
STEP 4
Knock-out opening4.2
5A
(A) In case of junction box mountingMake appropriate electrical connections to backplate harness, passing through knock-out opening
STEP 5 (B) In case of direct wire mounting (BX Connection):Connect the electrical feed to the backplate of the fixturethrough the knock-out opening, and make the electrical connections to the backplate harness
5B
Second 2-pin connector on0-10V dimming models only
(RDLBxxxxx08x)
Second 2-pin connector on0-10V dimming models only
(RDLBxxxxx08x)
FIXTUREWIRES
CEILINGWIRES
GREEN
BLACK BLACK
WHITE WHITE
GREEN
PURPLE +
FIXTUREWIRES
GREY -
FOR 0-10V DIMMABLE VERSION*
0-10VDC +
DC -
CEILINGWIRES GREEN
BLACK BLACK
WHITE WHITE
GREEN
PURPLE +
FIXTUREWIRES
GREY -
FOR 0-10V DIMMABLE VERSION*
0-10VDC +
DC -
CEILINGWIRES
L
N
G
L
N
G
FIXTUREWIRES
CEILINGWIRES
Armored cable (BX)
“X” Mounting hole distance
LEDBAR 24: 20in (508mm)LEDBAR 36: 32in (813mm)LEDBAR 48: 44in (1118mm)
Artemide inc.1980, New Highway, Farmingdale (NY) 11735T. +1 631 694 9292 | infousa@artemide.net | www.artemide.net
Artemide Ltd.11105, rue Renaude Lapointe, Montréal (QC) H1J 2T4
T. +1 514 323 6537 | infocanada@artemide.net | www.artemide.net2
Backplate
Fixture
5/64”
STEP 6
LEDBAR 24/36/48WALL/CEILING
Assembly instructions
rev 0.1Y503-11000
1. Fix the mounting plate to the wall using the holes previously drilled (screws not supplied)
PUSH
2. Connect the backplate’s female to the fixture’s male connector (yellow)
3. Mount the fixture to the backplate and secure it using the screws removed in STEP 2.2
STEP 7 Screw the end caps back onto the fixture
6.1 6.2
6.3
Second 2-pin connector on0-10V Dim models only
(RDLBxxxxx08x)
Artemide inc.1980, New Highway, Farmingdale (NY) 11735T. +1 631 694 9292 | infousa@artemide.net | www.artemide.net
Artemide Ltd.11105, rue Renaude Lapointe, Montréal (QC) H1J 2T4
T. +1 514 323 6537 | infocanada@artemide.net | www.artemide.net3
Recommended