View
221
Download
4
Category
Preview:
Citation preview
1 2
LAMIERE DA COILS
2
LAMIERE DA COILS
3
TABELLA DI COMPARAZIONE TRA LE NORMEComparison table between the standards
IN VIGORE E LE PRECEDENTI NORMATIVE NAZIONALIin force end previous national standards
DesignazioneDesignation
Precedenti designazioni equivalenti - Previous equal designations
EN 10025-95 EN 10027-2 EN 10025-
90GermaniaDIN 17100
FrenciaNFA 35.501
Regno Unito BS 4360
Spagna UNE 36080
Italia UNI 7070
Belgio NBN
SveziaNS Portogallo Austria Norvegia
USA ASTMA570
GiapponeJIS 3106
S 185 1.0035 Fe310-0 St33 A33 A310-0 Fe320 A320 13 00-33 Fe310-0 St320
S235 1.0037 Fe360-B St37.2 E24.2 Fe360B AE235B 13 11-00 Fe360B NS12 120
S235LRG1 1.0036 Fe360B-FU Ust37.2 AE235B-FU Ust360B NS12 122
S234JRG2 1.0038 Fe360B FN RSt37.2 40B AE235B-FN 13 12-00 RSt360B NS12 123
S235J0 1.0114 Fe360 C St37.3 U E24.3 40C AE235C Fe360C AE235C Fe360C St360C XS12 124 Grade 36 SM 41
St360CE
S235J2G3 1.0116 Fe360 D1 St37.3 N E24.4 40D AE235D Fe360D AE235D Fe360D St360D NS12 124
S235J2G4 1.0117 Fe360 D2
S275JR 1.0044 Fe430 B St44.2 E28.2 43D AE275B Fe430B AE255B 14 12-00 Fe430B St430B NS12 142
S275J0 1.0143 Fe430C St44.3 U E28.3 43C AE275C Fe430C AE255C Fe430C St430C NS12 143 Grade 40 SM 50
St430CE
S275J2G3 1.0144 Fe430D1 St44.3 N E28.4 43D AE275D Fe430D AE255D 14 14-00 Fe430D St430D NS12 143
S275J2G4 1.0145 Fe430D2 14 14-01
S355JR 1.0045 Fe510B E36.2 50B AE355B Fe510B AE355B Fe510B
S355J0 1.0553 Fe510C St52.3 U E36.3 50C AE355C Fe510C AE355C Fe510C St510C NS12 153
S355J2G3 1.0570 Fe510d1 St52.3 N 50D AE355D Fe510D AE355D Fe510D St510D NS12 153 Grade 50 SM 53
S355J2G4 1.0577 Fe510D2
S235K2G3 1.0595 Fe510DD1 E36.4 50DD AE510DD Fe510DD
E295 1.0050 Fe490.2 St50.2 A50.2 A490 A490 Fe490 15 50-00/01 Fe490.2 St490
E335 1.0060 Fe590.2 St60.2 A60.2 A590 A590 Fe590 16 50-00/01 Fe590.2 St590
E360 1.0070 Fe690.2 St70.2 A70.2 A690 A690 Fe690 15 55-00/01 Fe690.2 St690
Per quanto riguarda questa categoria di prodotti esiste dal febbraio 1992 la EN 10025 che sostituisce tutte le varie normative nazionali della Comunità Europea.Le vecchie norme. quindi. non sono più applicabili. Ciò nonostante. per aiutare ad individuare i prodotti richiesti da parte di clienti che non fossero del tutto informati sulla reale situazione. vengono date delle tabelle di comparazione riferite alle vecchie normative.
EN 10025 exist since February 1992 regarding this category of products and consequently replaces all the various national standards of the European Community. The old standards are no longer applicable. In spite of this a comparative table that refers to these old standards is given to help customers determine the products they require when they are not fully informed about the current situation.
EN 100025.95 EN 100025.95
4
LAMIERE DA COILS
LAMIERE IN QUALITÀ DA COSTRUZIONE
SECONDO NORMATIVA EUROPEA EN 10025 (sostituisce uni 7070) – CON CERTIFICATO DI ANALISI CHIMICA E PROVE MECCANICHE DI ACCIAIERIA SECONDO EN 102043. LB (sostituisce din 50049)
– CON TOLLERANZE DIMENSIONALI DI FORMA E SULLA MASSA SECONDO EN 10029 (sostituisce UNI EU 29)
BS-ACCIAI DI BASE- FE 360 B FN (S 235 JR)- FE 430 B FN (S 275 JR)- FE 510 B FN (S 355 JR)
AS - ACCIAI DI QUALITÀ
- FE 430 C FN (S 275 JO)- FE 430 D1 FF (S 275 J2 G3)- FE 510 c FN (S 355 JO)- FE 510 D1 FF (S 355 J2 G3)- FE 510 DD1 FF (S 355 K2 G3)
LEGENDA: BS - ACCIAI DI BASE
QS - ACCIAI DI QUALITA
FN . ACCIAI NON EFFERVESCENTI (semicalmati)
FF - ACCIAI COMPLETAMENTE CALMATI (a grana fine)
(S...) - DESIGNAZIONE QUALITATIVA SECONDO EN 10027-1
LAMIERE DA SCAFO CON COLLAUDO * RINA * LLOYD'S REGISTER OF SHIPPING * AMERICAN BUREAU OF SHIPPING * BUREAU VERITAS * DET NORSKE VERITAS (NEI VARI GRADI PREVISTI)
– LAMIERE IN ACCIAI BONIFICATI - ad alto snervamento ed antiusura – LAMIERE IN ACCIAIO C45 normalizzate – BRAMM LAMINATE, con spessore da 80 a 400 mm – LAMIERE DA TRENO DA BRAMME ECCEDENTI – LAMIERE E BRAMME da stock
CERTIFICAZIONI E COLLAUDI PARTICOLARI – SECONDO D.M.14/02/92 (Legge 5.11.1971 n° 1086). – Con collaudi FERROVIE dello STATO. – Con collaudi dei vari ENTI CERTIFICATORI. – CON CONTROLLO AD ULTRASUONI (U.T.) NELLE VARIE CLASSI.
Secondo Normative: EN 10028
– P265GH
– P355NH
– P275 NH
LAMIERE IN QUALITÀ DA CALDARERIA
Secondo Normativa ASME:
– SA 515 GR 60 e 70
– SA516 GR 60 e 70
ACCIAI NON LEGATI PER CALDAIE E RECIPIENTI A PRESSIONE corrispondenze indicative tra le principali designazioni europee e americane
ITALIAUNI 5869
1975
EURONORMEN 10028B/2
1993
USAASTM/ASMEEDIZ. 1995
GERMANIADIN 17155
1983
FRANCIAAFNOR NF
A 36.205-82
INGHILTERRAB.S. 1501
1981
Fe 360. 1 KW
Fe 360. 1 KG
Fe 360. 2 KW
Fe 360. 2 KG
P 235 G H A 285 Gr. C/A 515
Gr. 65
-
A 516 Gr. 55
-
HI
-
-
-
A 37 CP
-
-
-
-
-
161 gr. 360 B
161 gr. 360 A
Fe 410. 1 KW
Fe 410. 1 KG
P 265 G H A 515 Gr. 60
-
-
-
A 42 CP
-
-
-
Fe 410. 2 KW
Fe 410. 2 KG
A 516 Gr. 60
-
-
-
-
-
161 gr. 430 B
161 gr. 430 A
Fe 460. 1 KW
Fe 460. 1 KG
Fe 460. 2 KW
Fe 460. 2 KG
P 295 G H A 515 Gr. 65
-
A 516 Gr. 65
-
HII
-
A 48 CP
-
-
-
-
-
-
Fe 510. 1 KW
Fe 510. 1 KG
Fe 510. 2 KW
Fe 510. 2 KG
P 355 G H A 515 Gr. 70
-
A 516 Gr. 70
-
-
-
-
-
A 52 CP
-
-
-
-
-
-
-
5 6
LAMIERE DA COILS
7
Gradi di disossidazione, si distinguono nel seguente modo:
• facoltativo, grado a scelta del produttore dell'acciaio
• FU, acciaio effervescente
• FN, acciaio effervescente non autorizzato
• FF, acciaio completamente calmato contenente una quantità sufficiente di elementi atti a legare I'azoto presente (per es. Al min 0,02%) . Nel caso di impiego di altri elementi, questi devono essere indicati nei documenti di controllo
I vari gradi qualitativi differiscono tra loro per quanto riguarda la saldabilità ed i valori di resilienza prescritti e si distinguono nel seguente modo:
• JR, (ex 1},2 B della vecchia EN 10025), rappresenta gli acciai di base (BS) a meno che non sia specificata l'idoneità alla deformazione a freddo
• JO, J2G3, J2G4, K2G3, K2G4(ex rispettivamente C, 01, 001, 002 della vecchia EN 10025), sono gli acciai di qualità (QS), si differenziano tra loro per la diversa saldabilità e soprattutto per il grado di resilienza (vedere tabella)
• J2G3e K2G3 (ex rispettivamente 01, 001 della vecchia EN 10025), sono in genere forniti allo stato di laminato normalizzato
Acciai per impiego strutturale EN 10025.95 - SteelsforstrurturaluseEN10025.95Caratteristiche meccaniche - Mechanicalproperties
QualitàQuality
sec.denom.EN 10027
Disoss. Sottogr.
Resistenza sps no-minale Snerv.
YieldstressN/mm2
min
Allungamento EnlongationA min L0 = 80 A min Resilienza per s > 10
Resiliencefors>10
< 3 mm ≥ 3 ≤ 100 mm > 1 ≤ 1,5 > 1,5 ≤ 2 > 2 ≥ 2,5 > 2,5 ≥ 3 L0 = ≤ 40 Temp. J
S185 a sceltato be chosen BS 310+540 290+510 185 L 11
T 9L 12T 10
L 13T 11
L 14T 12
L 18T 16
--
--
S235JR a scelta BS
360+510 340+470 235 L 18T 16
L 19T 17
L 20T 18
L 21T 19
L 26T 24
20 27
S235JRG FU BS 20 27
S235JRG2 FN BS 20 27
S235J0 FN QS 0 27
S235J2G3 FF QS -20 27
S235J2G4 FF QS -20 27
S275JR FN BS
430+580 410+560 275 L 15T 13
L 16T 14
L 17T 15
L 18T 16
L 22T 20
20 27
S275J0 FN QS 0 27
S275J2G3 FF QS -20 27
S275J2G4 FF QS -20 27
S2355JR FN BS
510+680 490+630 355 L 15T 13
L 16T 14
L 17T 15
L 18T 16
L 22T 20
20 27
S355J0 FN QS 0 27
S355J2G3 FF QS -20 27
S355J2G4 FF QS -20 27
S355K2G3 FF QS -20 40
S355K2G4 FF QS -20 40
La tabella vale per spessori fino a 40 mm max. The table is valid for up to a max thickness of 40 mm.
Acciai per impiego strutturale - Steels for strurtural use EN 100025.95
8
LAMIERE DA COILS
9 10
Acciai ad alto limite di snervamentoHigh yield limit steels
Gli acciai ad alto limite di snervamento sono di concezione abbastanza recente e sono nati come acciai di marca di acciaieria. non regolati da norme. E quindi abbastanza frequente sentirne parlare secondo le varie designazioni di acciaieria piuttosto che secondo le denominazioni della EN 10149/95. Si distinguono due tipi di prodotti. quelli allo stato TM (allo stato di laminato a caldo normale. quello normalmente disponibile) e quelli allo stato NC (laminato a caldo e successivamente normalizzato per migliorarne le caratteristiche di defoflnabilità.
Gli acciai di questa norma sono destinati alla formatura a freddo (stampaggio). mentre quelli destinati alla fabbricazione di profili aperti sono regolati dalla EN 10113 da richiedersi espressamente.
Di seguito vengono quindi date le caratteristiche meccaniche previste e gli stati di fornitura. nonche la comparazione indicativa tra le varie marche di acciaieria. Vedere anche la UNI 9161.
Questi prodotti si distinguono nelle seguenti categorie:. prodotti laminati a caldo e sottoposti a trattamento termomeccanico (TM). prodotti laminati a caldo e sottoposti a trattamento di ricottura di normalizzazione (TD)
Hjgh yield limit steels are conceptually quite recent and are born as steels under the mark of the steelworks. They are not regulated by standards. We frequently hear them talked about therefore, according to the various steelworks names rather than according to the EN 10149/95 standard classifications. Two types of product can be distinguished: firstly the "TM" condion ones (generally available in the nominal hot rolled condion) and secondly the "NC" condion ones (hot rolled and then normalised to improve their deformation characteristics).
Steels of this standard are normnaIly destined to cold forming (pressing), whilst those destined for fabricating open sections are governed by the EN 10113 standard and must be expressly requested.
Below, we supply the mechanical characteristics, the supply conditons and a comparison guide to the various steelworks marks. See also thr UNI9161 norm.
These products are divided into the following categories:. hot rolled products subjected to thermo-mechanical treatment (TM). hot rolled products subjected to normalization annealing.
LAMIERE DA COILS EURONORM 10025 - UNI EU 28
DIMENSIONI IN MILLIMETRI
SPES
SORE
1000 X
2000
1250 X
2500
1500 X
3000
1500 X
6000
1750 X
6000
1800 X
6000
2000 X
6000
2000 X
8000 PESO
10,5 mq
10,8 mq 2 mq 3,1 mq 4,5 mq 9 mq 12 mq 16 mq
mm Kg/m PESO IN KG
1 7,85 5,7 24,5 35
1,2 9,42 8,8 29,5 42
1,5 1,8 23,6 36,7 53
1,8 14,1 28,2 44,2 64
2 15,7 31,4 49 71
2,5 19,6 39,3 61 86
3 23,6 47,1 73 106 212,4 247,3 255 282,6 376,8
3,5 27,5 55 86 124
4 31,4 62,8 98 141 282,6 329,7 339 377 502,4
5 39,3 78,5 123 176 352 412 424 472 628
6 47,1 94,2 147 212 424 494 509 565 753
7 55 110 172 247 494 576 594 660 879
8 62,8 126 196 282 564 659 678 754 1004
9 70,6 141 221 318 636 741 762 847 1130
10 78,5 157 245 353 706 824 848 942 1256
LAMIERE DA COILS
11 12
Trattandosi di prodotti destinati essenzialmente in impieghi di carpenteria, gli acciai
utilizzati sono in genere quelli della categoria strutturale, la qualità normalmente
disponibile a magazzino è la S235JR (Fe 36OB) della EN 10025: sono possibili anche
altre qualità ma solo dietro specifico accordo relativo alla materia prima.
As the products are destined essentially for structural steelwork uses, the steels used are
generally those of the structural category and the quality normally available in the
warehouse is S235JR (Fe 360B) of the EN 10025 standard. Other qualites are available,
but only on specific agreement for the raw materiaI.
Per le tolleranze delle bugne e delle strie si prega di far riferimento alle principali normative europee.
Far indentatian and ridge talerances, ptease refer ta the main European standards.
Lamiere striate o bugnateStriped and blickle steel plates LAMIERE STRIATE D’ACCIAIO laminate a caldo
EURONORM 10025 - UNI 7070 / EU 25-70
SPES
SORE
DIMENSIONI IN MILLIMETRI
PESO Kg/m 1000
X 2000
1000 X
3000
1250 X
2500
1500 X
3000
1500 X
6000
(1) mm PESO IN KG
2 18,2 36,4
2,5 22,2 45 69 100
3 28,6 57,2 85,8 89,4 128,7 257,4
4 38,5 73,0 109,5 114,0 164,3 328,5
5 44,3 88,6 132,9 138,5 199,4 398,7
6 52,1 104,2 156,3 163,0 234,5 468,9
7 60 120,0 180,0 187,5 270,0 540,0
8 67,8 135,6 203,4 211,9 305,1 610,2
10 83,6 167,2 250,8 261,2 376,2 752,4
12 99,1 198,2 297,3 309,7 446,0 891,9
14 115,0
SPESSORE mm PESO kg/m2
(1) Lo spessore si intende esclusa la striatura
* 2,5 22,2 3 4
28,6 36,5
5 6 7
44,3 52,1 60
8 10 12
67,8 83,6 99,1
* 14 115
LAMIERE DA COILS
LAMIERE BUGNATEEURONORM 10025 - UNI 7070 / EU 25
SPESSORE(1)
PESODIMENSIONI IN MILLIMETRI
2000 X 1000 2500 X 1250 3000 X 1500
mm Kg/m PESO IN KG
2,0 17,36 34,72 54,25 72,12
2,5 21,75 43,50 68,0 97,9
3 26,05 52,1 81,1 117,0
4 33,95 67,9 106,0 153,0
5 41,75 83,5 130,1 187,6
6 49,6 99,2 154 223
8 65,3 130,6 204 284
10 81,1 162,2 250 365
LAMIERE ZINCATE
NUMERO CALIBRO
SPESSOREmm
PESOKg/mq
NUMERO CALIBRO
SPESSOREmm
PESOKg/mq
34 0,20 1,75 25 0,55 4,70
33 0,23 1,99 24 0,50 5,10
32 0,25 2,14 23 0,70 5,90
31 0,27 2,30 22 0,80 6,65
30 0,30 2,73 20 1,00 8,25
29 0,35 3,13 28 1,25 9,90
28 0,40 3,52 27 1,50 12,15
27 0,45 3,91 14 2,00 16,10
26 0,50 4,30 12 2,50 20,05
10 3,00 29,35
SPESSORE mm PESO kg/m2
22,53
16,9720,8726,05
456
33,9541,7552,10
8 67,90
LAMIERE ZINCATE
NUMERO CALIBRO
SPESSOREmm
PESOKg/mq
NUMERO CALIBRO
SPESSOREmm
PESOKg/mq
34 0,20 1,75 25 0,55 4,70
33 0,23 1,99 24 0,50 5,10
32 0,25 2,14 23 0,70 5,90
31 0,27 2,30 22 0,80 6,65
30 0,30 2,73 20 1,00 8,25
29 0,35 3,13 28 1,25 9,90
28 0,40 3,52 27 1,50 12,15
27 0,45 3,91 14 2,00 16,10
26 0,50 4,30 12 2,50 20,05
10 3,00 29,35
LAMIERE GRECATE PER PARETI DIVISORIE, CONTROSOFFITTATURE E PANNELLATURE
EGB 4/80
CARATTERISTICHE STATICHE DELLA SEZIONE
SPESSORE 0,6 0,7 0,8 1,0 1,2
PESO Kg/m 4,71 5,49 6,28 7,85 9,36
PESO Kg/m2 5,60 6,53 7,47 9,34 11,14
13
3
14
LAMIERE DA COILS
CARATTERISTICHE STATICHE
SPESSORE 0,6 0,7 0,8 1,0
PESO Kg/m 5,89 6,87 7,85 9,81
J cm4/m 16,05 18,72 21,40 26,75
W cm3/m 5,30 6,18 7,07 8,83
LAMIERE GRECATE PER PARETI
I valori delle portate in grassetto tengono calcolo di una freccia ≤ 1/200 1.
Quando non specificato, la prevemiciatura avviene sulla faccia 1.
Carico max uniformemente distribuito in Kg/m2 per resistenza o = 1450 kg/cm2.
I CARICHI PIÙ ELEVATI NON PREVEDONO LIMITAZIONI DI FRECCIA
EGB 1250
ppSpessore Distanza fra gli appoggi in metri
mm 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00
0,6 614 393 273 200 153 121115
9884
8163
6848
5838
0,7 716 458 318 234 179 414135
11498
9473 7957 67
445835
0,8 820 524 364 287 205 162154
131112
10884
9165
7751
6741
5833
1,0 1024 655 455 334 256 202193
163140
135105
11381
9764
8351
7241
6434
Freccia cm 0,23 0,36 0,52 0,71 0,92 1,12 1,25 1,37 1,50 1,62 1,75 1,67 2,00
pppp
0,6 768 491 341 251 192 152 123 101 8581
7264
6251
0,7 896 573 398 292 224 177 143 118 9995
8474
7359
6348 b
11,8 1025 656 455 334 256 202 164 135 113108
9785
8368
7255
6445
1,0 1280 819 569 418 320 253 204 169 142135
121106
10485
9169
8057
Freccia cm 0,17 0,27 0,39 0,53 0,70 0,88 1,09 1,31 1,50 1,62 1,75 1,87 2,00
Per trasformare i kg/m2 dividere per 1,02
CARATTERISTICHE STATICHE
SPESSORE 0,6 0,7 0,8 1,0
PESO Kg/m2 6,42 7,49 8,57 10,72
PESO Kg/m 1000 1250
4,715,88
5,496,89
6,287,85
7,859,81
J cm4/m 14,1 16,42 18,76 23,38
W cm3/m 4,9 5,72 6,56 8,82
LAMIERE GRECATE PER COPERTURE
I valori delle portate in grassetto tengono calcolo di una freccia ≤ 1/200 1.
Quando non specificato, la prevemiciatura avviene sulla faccia 1.
Carico max uniformemente distribuito in Kg/m2 per resistenza o = 1450 kg/cm2.
I CARICHI PIÙ ELEVATI NON PREVEDONO LIMITAZIONI DI FRECCIA
EGB 401
pppp
0,6 711 455 316 232 178 140 114 9494
7970
6755
5844
5136
44-
0,7 829 531 369 271 207 164 133 110106
9282
7964
6851
5942
5234
0,8 921 609 423 311 238 188 152 126121
10693
9073
7859
6848
5939
1,0 1192 763 530 389 298 235 191 158151
132116
11392
9773
8560
7449
Freccia cm 0,19 0,29 0,42 0,58 0,75 0,85 1,17 1,38 1,50 1,63 1,75 1,88 2,00
Per trasformare i kg/m2 dividere per 1,02
ppSpessore Distanza fra gli appoggi in metri
mm 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00
0,6 565 364 253 186 142142
112100
9173
7556
6345
5433
46-
40-
36-
0,7 664 425 295 217 166166
131116
10685
8864
7449
6339
54- 47 41
-
0,8 761 487 338 248 190189
150133
12297
10173
8556
7244
6235 54 48
-
1,0 954 610 424 311 238236
188166
153121
12691
10670
9055
7844
6836
60-
Freccia cm 0,25 0,39 0,56 0,77 1,00 1,13 1,25 1,38 1,50 1,63 1,75 1,88 2,0015
15 16
LAMIERE DA COILS
LAMIERE GRECATE PER SOLAI
EGB 210
ppSpessore Distanza fra gli appoggi in metri
mm 1,00 1,25 1,50 1,75 2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 1,25 4,50 4,75 5,00
0,6 1415 905 629 462 354 280 226218
187164
157126
13499
1679
10165
8853
7814
7037
6332 57
0,7 1757 1125 781 574 439 347 281265
232199
195153
166120
4396
12578
11065
9757
8745
7838
7033
0,8 2120 1357 942 692 530 419 339313
280235
236181
201143
7314
15193
13376
11764
10554
9446
8539
1,0 2901 1857 1299 947 725 573566
464412
384310
322239
275188
237150
206122
181101
16184
14371
12961
11652
1,2 3734 2390 1660 1219 934 738697
597508
494382
415294
354231
305185
266150
233124
207103
18487
16574
14963
1,5 4960 3168 2200 1616 1237 978887
792632
655475
550365
469288
400230
352187
309154
274129
244108
21992
19879
Freccia cm 0,21 0,33 0,48 0,65 0,85 1,12 1,25 1,38 1,50 1,63 1,75 1,80 2,00 2,13 2,25 2,38 2,50
CARATTERISTICHE STATICHE
SPESSORE 0,6 0,7 0,8 1,0 1,2 1,5
PESO Kg/m2 7,85 9,16 10,47 13,08 15,07 19,62
PESO Kg/m 1000 1250
4,715,88
5,496,86
6,287,85
7,859,81
9,4211,77
11,7714,71
J cm4/m 42,19 51,28 60,67 79,92 98,39 122,4
W cm3/m 12,2 15,5 18,28 79,92 98,39 122,4
I valori delle portate in grassetto tengono calcolo di una freccia ≤ 1/200 1.
Quando non specificato, la prevemiciatura avviene sulla faccia 1.
Carico max uniformemente distribuito in Kg/m2 per resistenza o = 1450 kg/cm2.
I CARICHI PIÙ ELEVATI NON PREVEDONO LIMITAZIONI DI FRECCIA
pppp
0,6 768 491 341 251 192 152 123 101 8581
7264
6251
126108
11189
9674
8762
7853
7145
0,7 896 573 398 292 224 177 143 118 9995
8474
7359
6348 b
137108
12290
10876
9764
8855
11,8 1025 656 455 334 256 202 164 135 113108
9785
8368
7255
6445
147106
13189
11776
10665
1,0 1280 819 569 418 320 253 204 169 142135
121106
10485
9169
8057
201140
179118
161100
14566
1,2 4668 2987 2074 1524 1167 922 147 617 519490
442385
381308
332351
292207
258172
230145
207123
187106
1,5 6187 3960 2750 2020 1547 1222 990 818791
687610
586479
505384
440312
387257
343214
306181
274154
247132
Freccia cm 0,17 0,27 0,39 0,53 0,70 0,88 1,09 1,31 1,50 1,62 1,75 1,87 2,00 2,13 2,25 2,38 2,50
Per trasformare i kg/m2 dividere per 1,02
CARATTERISTICHE STATICHE DELLA SOLETTA m =10
H cm peso soletta kg/m2
spessore la-miera mm Xs cm JTOT cm
4/m Ws cm3/m Wl cm
3/m T kg/m
9 165
0,70,81,01,21,5
2,903,043,283,483,73
291320374423490
10031052114012151313
47,753,5165,3876,6392,97
1030
10 190
0,70,81,01,21,5
3,183,333,613,834,12
383422493557684
12041267136514541563
56,1563,2677,1593,51
109,52
1130
11 215
0,70,81,01,21,5
3,443,613,914,174,48
493543634718830
14331504162117211852
65,273,4789,42
105,12127,30
1250
12 240
0,70,81,01,21,5
3,683,874,214,494,83
621684800905
1047
16871767190020152167
74,6384,13
102,69120,50146,02
360
CARATTERISTICHE STATICHE DELLA LAMIERA
spessore mm 0,7 0,8 1,0 1,2 1,5
peso kg/m2 9,16 10,47 13,08 15,7 19,62
peso kg/m 5,49 6,28 7,55 9,42 11,77
JTOT cm4/m 57,14 65,3 81,63 98,39 122,45
JRIDOTTO cm4/m 51,28 60,67 79,92 97,96 122,45
Ws cm3/m 15,15 18,28 25,01 32,19 42,67
Wl cm3/m 21,59 2504 32,00 38,99 49,38
Y cm 2,48 2,48 2,48 2,48 2,48
Al cm2/m 11,66 13,33 16,66 20 25
DIAMETRI RETA A MAGLIA SALDATADA 150 X 150 mm
altezza soletta cm
distanza tragli appoggi 9 10 11 12
< 2,00 mm 3,5 3,5 4,0 4,5
2,00 ÷ 3,600 m 3,5 4,5 4,5 4,5
> 3,60 m 4,5 5,0 5,0 5,0
EGB 210 collaborante
17 18
LAMIERE DA COILS
LAMIERE GRECATE PER SOLAI
spessore mm peso kg/m2 spessore mm peso kg/m2
0,250,280,30
2,262,522,72
0,60,81,0
5,437,249,05
0,350,40,5
3,183,644,56
1,251,5
11,3013,57
distanza tra gli appoggim
0,5 0,6
spessore (mm)/tipo
0,8 1,0 1,25 1,5
1,01,251,5
1,752,0
2,25
13565
16080
21010560
26513072
3301659050
40020011060
1,01,251,5
1,752,0
2,25
22511065
26513575
35018010055
4452251257050
5602801609060
67033519010570
CARICO MAX UNIFORMEMENTE DISTRIBUITO IN kg/m2
I nastri rilaminati a freddo sono divisi in due categorie:•Coils a freddo larghi con larghezza ≥ 600 mm•Nastri a freddo stretti con larghezza < 600 mmOgnuna delle categorie è regolata da proprie nornle di fabbricazione e tolleranze dirnensionali.
Our cold rerolled strip are divided into two categories:•Widecoldrolledcoils:width≥600mm•Narrowcoldrolledstrips:width<600mmBoth of these two categories are governed by their own fabrication and dimensional tolerance standards.
COILS E NASTRI, LAMIERE SPECIFICHE TECNICHE
19
TECHNICAL SPECIFICATIONS OF COILS AND STRIPS,SHEETS AND HEAVY PLATES
20
LAMIERE DA COILS
21
Tolleranze di spessore EN 10051 - TolerancesonthicknessEN10051
Tolleranze per una larghezza nominale -Tolerancesforanominalwidth
Spessore nominaleNominalthickness ≤ 1200 > 1200 ≤ 1000 > 1500 ≤ 1800 > 1800
≤ 2,00 ± 0,17 ± 0,19 ± 0,21 -
> 2,00 ≤ 2,5 ± 0,18 ± 0,21 ± 0,23 ± 0,25
> 2,50 ≤ 3,00 ± 0,20 ± 0,22 ± 0,24 ± 0,26
> 3,00 ≤ 4,00 ± 0,22 ± 0,24 ± 0,26 ± 0,27
> 4,00 ≤ 5,00 ± 0,24 ± 0,26 ± 0,28 ± 0,29
> 5,00 ≤ 6,00 ± 0,26 ± 0,28 ± 0,29 ± 0,31
> 6,00 ≤ 8,00 ± 0,29 ± 0,30 ± 0,31 ± 0,35
> 8,00 ≤ 10,0 ± 0,32 ± 0,33 ± 0,34 ± 0,40
> 10,0 ≤ 12,5 ± 0,35 ± 0,36 ± 0,37 ± 0,43
> 12,5 ≤ 15,0 ± 0,35 ± 0,38 ± 0,40 ± 0,46
> 15,0 ≤ 25,0 ± 0,40 ± 0,42 ± 0,45 ± 0,50
Tolleranze sulla larghezza EN 10051 mm - WidthtolerancesEN10051
Tolleranze secondo EN 10051TolerancesaccordingtoEN10051
Larghezzanominale
Nominalwidth
Bordi grezzi Coarseedges Bordi cesoiati Shearededges
Inferiore Inferior Superiore Superior Inferiore Inferior Superiore Superior Simmetrica Simmetry
≤ 1200 0 + 20 0 + 3 ± 1> 1200 ≤ 1500 0 + 20 0 + 5 ± 1
> 1500 0 + 25 0 + 6 ± 1
Tolleranze sulla lunghezza EN 10051 mm - LenghttolerancesEN10051
Tolleranze secondo EN 10051-TolerancesaccordingtoEN10051
Larghezza nominale Nominalwidth secondo asEN 10051 Bordi cesoiati - Shearededges≤ 2000 - 0 +10 ± 1 mm
> 2000 ≤ 8000 - 0 + 0,005 x lunghezza nominalenominal lenght
± 0,1% % della lunghezza - for lenght
> 8000 - 0 + 40 -
Tolleranze di larghezza e lunghezza per le bandelle da nastro a caldo nere e/o decapate Width and lenghttolerancesforhot-rolledstripsblackand/orpicked
Dimensione nominaleNominaldimensions
Tolleranze ristretteLimitedtolerances
Tolleranze normaliNormaltolerances
≤ 80 < 150(1) ± 1 ± 1≤ 150 < 250(1) ± 1 ± 1≤ 250 < 350 ± 0,5 ± 1≤ 350 < 500 ± 0,5 ± 1≤ 500 < 600 ± 0,5 ± 1
Tolleranze sulla planarità - Toleranceonplanarity
Spessore nominaleNominalthickness
Larghezza nominale Nominalwidth
Tolleranza di planarità Toleranceofplanarity
Tolleranza speciale di planarità Specialtolerance
ofplanarity
≤ 2,00 ≤ 1200 18 9> 1200 ≤ 1500 20 10> 1500 25 13
> 2,00 ≤ 25 ≤ 1200 15 8> 1200 ≤ 1500 18 9> 1500 23 12
Fuori squadro esciabolatura longitudinaleOut of square and longitudinal bow
Sciabolatura longitudinale, secondo la EN 10051:• per lamiere con una lunghezza nominale < 5000 mm q = 0,5% della lunghezza• per lamiere con lunghezza nominale ≥ 5000 mm, larghezza ≥ 600 mm e con bordi grezzi
di laminazione, q = 20 mm max, per ogni lunghezza di 5000 mm• per lamiere con lunghezza nominale ≥ 5000 mm, larghezza ≥ 600 mm e con bordi
remati, q = 15 mm max, per ogni lunghezza di 5000 mm
Fuori squadro: • il fuori squadro u non deve essere maggiore dell % della larghezza della lamiera secondo
la norma • su richiesta possiamo dare 0,3% max
Longitudinalbow,accordingtotheEN10051standard:•for sheets with a nominal length of < 5000 mm q= 0,5% of the length•forsheetswithanominallenght≥5000mm,widlh≥600mmandroughmillededges,q=
20 mm max, for every 5000 mm length•forsheetswithanominallenght≥5000mm,width2600mmandwidthtrimmededges,
q=15 mm max, for every 5000 mm length
Outofsquare:•the u out of square must not be greater than 1% of the sheet lenght according to the standard•on request we can give 0,3% max
EN 10051
22
LAMIERE DA COILS
23 24
Piani laminati a caldo ad alto limite di snervamentoHot-rolled flat products made of high yield strength steels for cold forming
Per le tolleranze dimensionali fa riferimento la EN 10051 con alcune varianti, secondo le tabelle seguenti:For the dimensional tolerances refeNo the EN 10051 standard wìth sevelal variations, according to the following tables.
EN 10149 1995 Tabella di conversione con le precedenti normative - Conversiontabletopreviousstandards
QualitàQuality
NumeroNumber EU 149 Pt2
Germania FranciaGran BretagnaBS 1449/1 Svezia
QStE SEW 0921) numero NF A36-231 NF A 36-203
- - Fe E 275 TM QStE 260 TM 1.8941 - E 275 D 40F30 -
S135 MC 1.0972 - - E 315 D E 355 D 43F35 -
S355 MC 1.0976 Fe E 355 TM QStE 340 TM 1.8942 E 355 D (E 390 D) 46F40 26 42-00
QStE 380 TM 1.8951
S420 MC 1.0980 Fe E 420 TM QStE 420 TM 1.8953 E 420 D E 455 D (50F45) 26 52-00
S460 MC 1.0982 - QStE 460 TM 1.8956 - - - -
- Fe E 490 TM - . E 490 D E 490 D - -
S500 MC 1.0984 - QStE 500 TM 1.8959 - - - 26 52-00
S550 MC 1.0985 (Fe E 560 TM)
QStE 550 TM 1.8948 (E 560 D) - 60F55 -
S600 MC 1.8969 - QStE 600 TM - - - - -
- - - - - E 620 D - 68F62 -
S650 MC 1.8976 - QStE 650 TM - - - - -
S700 MC 1.8974 - QStE 690 TM - (E 690 D) - 75F70 -
Classi di alcune qualità di acciaio da noi utilizzate normalmenteThe classes of some of the types of steel we normally use
Suddivisione in classi dei vari tipi di acciaio secondo la EN 10051Classdivisionofseveralsteelqualitiesacc.EN10051
Categoria B - Class B Categoria C - Class C Categoria D - Class DS355MC EN 10049 S420MC EN 10049 S490MC EN 10049
Tolleranze sulla planarità - Toleranceonplanarity
Spessore nominaleNominalthickness
Larghezza nominaleNominalwidth
Tolleranza di planarità secondo la categoriaToleranceaspercategories
B C D
≤ 25≤ 1200 18 23
Secondo accordiSecond agreements
> 1200 ≤ 1500 23 30> 1500 28 38
Alcune qualità elencate non sono riferite alla SEW092 ma ad altre norme precedenti (OSTE 600-650-690)Certain qualities do not concern the SEW092 but previous Standards (OSTE 600-650-690).
Acciai per impieghi strutturali con resistenza migliorata alla corrosione atmosferica sec. UNI EN 10155.95
Steels for structural uses with improved resistance to atmospheric corrosion - according to the UNI EN 10155.95 standard
Snervamento ReYieldstrenght
Resistenza RmTensilestrenght
way
Allungamento alla rotturaElongation
DesignazioneDesignation
Spessori nominali in mmNominalthicknessinmm
Spessori nominaliNominal
thicknessesL0 = 80 mm L0 = 5,65√S0
Sec. EN 10027ECISS IC 10 EN 10027 2 ≤ 16 > 16
≤ 40> 40≤ 63
> 63≤ 80
> 80≤ 100 < 3 ≥3≤100 > 1,5
≤ 2> 1
≤ 2,5> 2,5≤ 3
≥ 3≤ 40
> 40≤ 63
> 63≤ 100
S235JOWS235JOW
1.89581.8961 235 225 215 215 215 360+510 340+470 l
t1917
2018
2119
2624
2523
2422
S235JOWPS235J2WP
1.89451.8946
3030
3232
2828
3030
3232 510+680 490+630 l
t1614
1715
1816
2220
--
-.
S355JOWS355J2G1WS355J2G2WS355K2G1WS355K2G2W
1.89591.89631.89651.89661.8967
355 345 335 325 315 510+680 490+630 lt
1614
1715
1816
2220
2119
2018
senso
Acciai per impieghi strutturali con resistenza migliorataalla corrosione atmosfericaSteels for structural use with improved resistance to atmospheric corrosion
L'acciaio Cor- Ten, presentato sul mercato americano sin da11936, è apparso in Europa, in misura apprezzabile, soltanto intorno al 1958; viene attualmente prodotto da alcune acciaierie europee su licenza della UNITED STATE STEEL (USS)Il termine che identifica l'acciaio deriva da.
COR corrosione resistenteTEN resistenza meccanica
• COR TEN A, produzione Ilva, Resco 36 produzione Falck, FeS10A1KI (riferita a vecchie normative non più in vigore) produzione ISP (ARVEDI) sono assimilabili alla qualità S3S5JOWP.
• TOLLERANZE SPESSORE, per le tolleranze di spessore fare riferimento alle relative norme di prodotto, quindi.1. Lamiere da treno EN 100292. Lamiere da impiego diretto EN10051.
Cor - Ten steel, oflered in the American market since 1936, only appeared in Europe in any appreciable way starting from around 1958. It is currently produced by a few European steelworks under licence from UNITED STATE STEEL (U55) The term identifying the steel derives from
COR - corrosion resistantTEN - tensile strength•CORTEN A and the reference to liva production, Resco 36, Falk production explained,
Fe510A1 KI (referred to old standards no longer in force) 15P (ARVEDI) production are comparable to the 5355JOWP quality•THICKNE55 TOLERANCE5- for thickness tolerances refer to the rèlative product standards,
and therefore:1. Mill sheets - EN 10029 standard2. Direct use sheets - EN10051
Per le tolleranze dimensionali fa riferimento la EN100S1For dimensional tolerances refer to the EN 10051 Standard
LAMIERE DA COILS
25 26
Caratteristiche meccaniche sec. EN 10149 - EN10149mechanicalcharateristics
Qualità EN 10149QualityEN10149
ReN/mm2
RmN/mm2
A% min Piegamento 180°Folding180°
a = spessore thickness
Energia di rottura KV-Joule
BreakageenergyL0=80 L0=5,65√S0
S315 MC 315 390÷510 -20 24 a blocco da concordare
S355 MC 355 430÷550 19 23 0,5a da concordare
S420 MC 420 480÷620 16 19 0,5a da concordare
S460 MC 460 520÷670 14 17 1a da concordare
S500 MC 500 550÷700 12 14 1a da concordare
S550 MC 550 600÷760 12 14 1,5a da concordare
S600 MC 600 650÷820 11 13 1,5a da concordare
S650 MC 650 700÷880 10 12 2a da concordare
S700 MC 700 750÷950 10 12 2a da concordare
Caratteristiche meccaniche sec. EN 10149 - EN10049mechanicalcharateristics
Qualità EN 10149QualityEN10149
C%max
Mn%max
Si%max
P%max
S%max
Al % tot
maxNb%max
V%max
Ti%max
Mo%max
B%max
S315 MC 0,12 1,30 0,50 0,25 0,20 0,15 0,90 0,20 0,15
S355 MC 0,12 1,50 0,50 0,25 0,20 0,15 0,90 0,20 0,15
S420 MC 0,12 1,60 0,50 0,25 0,15 0,15 0,90 0,20 0,15
S460 MC 0,12 1,60 0,50 0,25 0,15 0,15 0,90 0,20 0,15
S500 MC 0,12 1,70 0,50 0,25 0,15 0,15 0,90 0,20 0,15
S550 MC 0,12 1,80 0,50 0,25 0,15 0,15 0,90 0,20 0,15
S600 MC 0,12 1,90 0,50 0,25 0,15 0,15 0,90 0,20 0,22 0,50 0,005
S650 MC 0,12 2 0,60 0,25 0,15 0,15 0,90 0,20 0,22 0,50 0,005
S700 MC 0,12 2,10 0,60 0,25 0,15 0,15 0,90 0,20 0,22 0,50 0,005
Piani laminati a caldo ad alto limite di snervamentoHot-rolled flat products made of high yield strenght steels for cold forming
Nastri da impiego diretto secondo la nuova norma EN 10111Strips for direct use according to the new EN 10111 standard
NuovadesignazioneNewdesignation
VecchiaOld
Analisi chimica maxMaxchemicalanalysis
Re (snervamento)Re(yieldstrenght) RM A % min
Prova pie-ga
Bendingtest
EN 10027 UNI 5867 C% Mn% P% S% 1,5≤e<2 2≤e<8 max 1,5≤e<2 2≤e<3 L0=5,65√S0 e<3 3≤e≤8
DD11 1.0332 P11 0,12 0,60 0,045 0,045 170+360 170+340 440 23 24 28 0e 1e
DD12 1.0398 N.A. 0,10 0,45 0,035 0,035 170+340 170+320 420 25 26 30 0e 0e
DD13 1.0335 P13 0,080 0,40 0,030 0,030 170+330 170+310 400 28 29 33 0e 0e
DD14 1.0389 N.A. 0,080 0,35 0,025 0,025 170+310 170+290 380 31 32 36 0e 0e
Tabella di conversione tra le qualità attuali e le vecchie normativeConversion table between the current qualities and the old standards
Norma qualitàReferencenormforquality
EN 10111 Uni 5867 ISO
17/N Din 1614 NFA A36.301 BS 1449 JIS G
3131SAEJ403
Norma dimensionaleDimensionalstandards
EN 10051 EN 10051 EN 10051 Din 1016 EN 10051 EN 10051 JIS G 131 -
Qualità specificaSpecificquality
- FeP10 HR1 - OC HR4 SPHC 1010DD11 FeP11 HR2 STW22 1C HR3 SPHC 10080012 - - - - - - -
- FeP12 HR3 STW23 2C HR2 SPHD 1008DD13 FeP13 HR4 STW24 3C HR1K SPHE 1006DD14 - - - - - - -
Acciai laminati a caldo da impiego diretto o per stampaggio a freddoHot rolled steel for end use or for deep drawing
Di seguito vengono date le caratteristiche meccaniche previste per questi tipi di acciaio partendo dalle normative nazionali.I nastri da impiego diretto. essendo normalmente soggetti ad operazioni di stampaggio, vengono ordinati decapati, ciò nonostante possono anche essere richiesti neri.
Below, we supply the mechanical characteristics estabilished for these types or steel. starting with national standards. Strips for direct use which are normally subject to pressing operations are oriented in a picked condition. They call however be requested black.
Tutte le qualità indicate, ad eccezione della 0011, devono essere fornite con acciaio calmato. Le caratteristiche meccaniche della qualità 0011 vengono garantite per un mese dalla fornitura, le altre per sei mesi Nella terza colonna viene data la corrispondenza con le vecchie qualità, quelle indicate con N.A. significa che non ce l'hanno. La conversione con le vecchie qualità della UNI5867 è puramente indicativa.
Ali the qualities indicated, with the exception of 0011, must be supplied with killed steel. The mechanical characteristics of the 0011 quality are guaranteed for one month from supply, the others for six months The correspondence with the old qualities is given in the third column those marked with N.A. do not have any correspondence The conversion with the old UNI5867 norm qualities is purely indicative.
LAMIERE DA COILS
27 28
Tolleranze di spessore di prodotti larghi rilaminati a fredd EN 10131Thickness tolerances for cold rolled coils EN 10131
Spessore nominaleNominalthickness
Tolleranze normaliNormaltolerances
Tolleranze ristretteLimitedtolerances
≤ 1200 > 1200≤ 1500 > 1500 ≤ 1200 > 1200
≤ 1500 > 1500
> 0,6 ≤ 0,8 ± 0,06 ± 0,07 ± 0,08 ± 0,040 ± 0,050 ± 0,05> 0,80 ≤ 1,00 ± 0,07 ± 0,08 ± 0,09 ± 0,045 ± 0,060 ± 0,06> 1,00 ≤ 1,20 ± 0,08 ± 0,09 ± 0,10 ± 0,055 ± 0,070 ± 0,07> 1,20 ≤ 1,60 ±0,10 ± 0,11 ± 0,11 ± 0,070 ± 0,080 ± 0,08> 1,60 ≤ 2,00 ± 0,12 ± 0,13 ± 0,13 ± 0,080 ± 0,090 ± 0,09> 2,00 ≤ 2,50 ± 0,14 ± 0,15 ± 0,15 ± 0,100 ± 0,110 ± 0,11> 2,50 ≤ 3,00 ± 0,16 ± 0,17 ± 0,17 ± 0,110 ± 0,120 ± 0,12
Norme in vigoreNew rules
Riferimenti a vecchie normativeReference to old specifications
Nastri larghi - Widestrips Nastri larghi -Widestrips
EN 10130 UNI 5866 DIN 1623Pt1
NF A 36 401
BD 1449Pt2.83 ASTM JIS
G3141.77GOST
9045.80DC01 P01 St12 C CR SP4 A 366.85 cl 1 SPCCTDC03 P02 St13 E CR SP3 A 619.82 cl 2 SPCD VG 08KP
- SV 08JUDC04 P04 St14 ES CR SP1 A 620.84 cl 3 SPCEN OSV 08JUDC05 - - - - - - -DC06 - - - - - - -
Coils e lamiere rilaminati a freddo larghi EN 10131 toll. sec. EN 10131Cold rolled coils and sheets EN 10131 tolerances sec. EN 10131
DesignazioneDesignations
Caratteristiche meccanicheMechanicalproperties
Analisi di colata % maxCastinganalysis
Sec. la EN 10027 e il CR 10260
Sec. la EN 10027
ReN/mm2
RmN/mm2
A80% min
r90minn90min C P S Mn Ti
DC01 1.0330acciaio non pregiato di
qualità
a discrezione
del produttore
--
AB
-3 mesi 280 270+410 28 0,12 0,045 0,045 0,60
DC03 1.0347acciaio non pregiato di
qualità
totalmente calmato
6 mesi6 mesi
AB
6 mesi6 mesi 240 270+370 34 1,30 0,10 0,035 0,035 0,45
DC04 1.0338acciaio non pregiato di
qualità
totalmente calmato
6 mesi6 mesi
AB
6 mesi6 mesi 210 270+350 38 1,60 0,180 0,08 0,030 0,030 0,40
DC05 1.0312acciaio non pregiato di
qualità
totalmente calmato
6 mesi6 mesi
AB
6 mesi6 mesi 180 270+330 40 1,90 0,200 0,06 0,025 0,025 0,35
r min n min
DC06 1.0873acciaio non pregiato di
qualità
totalmente calmato
6 mesi6 mesi
illimitataillimitata 180 370+350 38 1,80 0,220 0,02 0,020 0,020 0,25 0,30
Gra
do d
idis
oss
idazi
one
Gradeofdeo
xidation
Defin
izio
ne e
cla
ssifi
c. s
ec. l
a EN
100
20Clas
sifica
tionacc.to
EN100
20
Dura
ta d
i val
idità
del
le
cara
tt. m
ecca
nich
eValid
itydurationof
mechanicalp
roperties
Aspe
tto s
uper
ficia
leSu
rfaceapperance
Ass
enza
linee
scorr
imen
toAb
senceofstre
tche
stra
ims
Tolleranze di spessore di prodotti larghi rilaminati a freddo EN 10131Thickness tolerances for cold rolled coils EN 10131
Tolleranze sulla larghezza dei coils non refilati-Tolerancesonwidthofuntrimmedcoils
Larghezza nominaleNominalwidth
Tolleranze normali - Normaltolerances Tolleranze ristrette - Limitedtolerances
Negativa Negative Positiva Positive Negativa Negative Positiva Positive≤ 1200 0 + 4 0 + 2
> 1200 ≤ 1500 0 + 5 0 + 2> 1500 0 + 6 0 + 3
Tolleranze sulla lunghezza dei fogli ricavati da prodotti larghi con bordi grezzi rilaminati a freddo EN 10131
Lenght tolerances for sheets from cold rolled wide bands coils with mill edge EN 10131
Tolleranze sulla lunghezza delle lamiere spianate con bordi grezziTolerancesonthelenghtofflatplateswithroughedges
Lunghezza nominaleNominalwidth
Tolleranze normali - Normaltolerances Tolleranze ristrette - Limitedtolerances
Negativa Negative Positiva Positive Negativa Negative Positiva Positive< 2000 mm 0 6 0 + 2
≤ 2000 mm 0 0,3% della lunghezza0,3% of lenght 0 0,15% della lunghezza
0,15% of lenght
Tolleranze sulla lunghezza dei fogli ricavati da prodotti larghicon bordi refilati rilaminati a freddo EN 10131
Lenght tolerances for sheets from cold rolled wide bands coils with slit edge EN 10131
Tolleranze sulle dimensioni delle lamiere spianate con bordi refilatiTolerancesondimensionsofflatplateswithfinishededges
Dimensioni nominaliNominaldimensionthicknessandlenght
Tolleranze normali mmNormaltolerancesmm Tolleranze ristrette - Limitedtolerances
Toll. larghezza(1)
TolerancesonwidthToll. lunghezzaTolerancesonwidth
Toll. larghezzaTolerancesonwidth
Toll. lunghezzaTolerancesonwidth
0,4+3 x 2000 mm± 0,4 mm
6± 0,2 mm
3
0,4+3 x ≥ 2000 mm 0,3% della lunghezza0,3% of lenght
0,15% della lunghezza0,15% of lenght
Tolleranza sulla planarità dei prodotti larghi rilaminati a freddo EN 10131Flatness tolerances for cold rolled wide bands coils EN 10131
Tolleranze sulla planarità delle lamiere spianate con snervamento inferiore a 280 N/mm2
Tol.onplanarityofflatplateswithyieldstrenghtlowerthan280N/mm2
Classe di tolleranzaTolerancesofclass
Larghezza nominaleNominalwidth
Spessore nominale - Nominalthickness
< 0,7 mm ≥ 0,7 < 1,2 mm ≥ 1,2 mm
Tolleranze normaleNormaltolerances
≥ 600 < 1200 12 10 8≥ 1200 < 1500 15 12 10
≥ 1200 19 17 15
Tolleranze ristrettaLimitedtolerances
≥ 600 < 1200 5 4 3≥ 1200 < 1500 6 5 4
≥ 1500 8 7 6
LAMIERE DA COILS
29 30
Tolleranza sulla planarità dei prodotti larghi rilaminati a freddo EN 10131Flatness tolerances for cold rolled wide bands coils EN 10131
Tolleranze sulla planarità delle lamiere spianate con snervamento ≥ a 360 N/mm2
Tol.onplanarityofflatplateswithyieldstrenght≥than360N/mm2
Classe di tolleranzaTolerancesofclass
Larghezza nominaleNominalwidth
Spessore nominale - Nominalthickness
< 0,7 mm ≥ 0,7 < 1,2 mm ≥ 1,2 mm
Tolleranze normaleNormaltolerances
≥ 600 < 1200 15 13 10≥ 1200 < 1500 18 15 13
≥ 1200 22 20 19
Tolleranze ristrettaLimitedtolerances
≥ 600 < 1200 8 6 5≥ 1200 < 1500 9 8 6
≥ 1500 12 10 9
EN 10130 / EN 10131
Fuori squadro e sciabolatura longitudinaleOut of square and longitudinal bow
Sciabolatura longitudinale:• q max 6 mm per una lul1ghezza ~ 2 m• q max 0,3% per lunghezze < 2 m• Fuorisquadro:• il fuori squadro u non deve essere maggiore dell % della larghezza della lamiera
Longitudinal bow:• q max 6 mm for a length ≥ 2 m• q max 0.3% for length < 2 m
Out of square:• u must not exceed 1% o[ sheet's width
Comparizione tra le specifiche tecniche riguardanti la superficie delle varie normativeComparison between technical specifications of several standards concerning the surface
Descrizione delle difettosità accettabiliDefinitionofacceptableflaws
EN10139
Uni5961
DIN1624
NF A 37501
BS 14491.1 e 1.9
JIS3141
Accettazione superficiale
Surfaceacceptance
Superfici lisce, metallicamente pure.Sono consentiti puntinature, piccoli difetti e leggere rigature.Smooth surface, free from metal residues. Pits, small defects and slight flows are allowed.
MA MA BKex GBK
S1 GP
Accettazione superficiale per
superfici ≤ 2,0 mmSurfaceallowanceforthickness≤2,0mm
Superfici lisce, metallicamente pure.Puntinature, rigature e striature sono ammissibili in misura assai ridotta, sempreche esse non pregiudichino l'aspetto liscio e uniforme della superficie osservata ad occhio nudo.Smooth surface, free from metal residues Pits, groves and flows are partly allowed, provided that they do not compromise the smooth and uniform apperance of the surface noticed with the naked eye.
MB MB RP S2 FF
Accettazione superficiale per
superfici ≤ 1,0 mmSurfaceallowanceforthickness≤1,0mm
Superfici lisce, metallicamente pure.Puntinature, rigature e striature sono ammissibili in misura assai ridotta, sempreche esse non pregiudichino l'aspetto di finitura brillante della superficie.Smooth surface, free from metal residues Pits, groves and flows are partly allowed, provided that they do not compromise the bright apperance.
MC RPG S3 FF
Rugosità superficiale RR
SurfaceroughnessRR
Superficie con rugosità matta, ovvero molto rugosa;
Ra ≥ 1,5 µmRa ≥ 60 µinch
Matt surface, remarkably rough
RR RR R S1m M -
Rugosità superficiale RM
SurfaceroughnessRM
Superficie rugosa; Ra 0,6+1,8 µmRa 24+72 µinch
Rough surface
RM RM M S1m BR D
Rugosità superficiale RL
SurfaceroughnessRL
Superficie lucida; Ra ≥ 0,6 µmRa ≥ 24 µinch
Semi-bright surface
RL RL G S2 PLplating finishh
B
Rugosità superficiale RN
SurfaceroughnessRN
Superficie brillante; Ra ≥ 0,2 µmRa ≥ 8 µinch
Bright surface
RN RN B S3Ra 0,2
µm
-
EN 10139
LAMIERE DA COILS
31 32
Qualità ed analisi chimiche secondo EN 10139 Quality and chemical analyses according to the EN 10139 standard
Design.sec.Design.acc.
EN 10027-1
Condizioni fonitura
Supplycond.Simb. Re
N/mm2Rm
N/mm2
Allungamento % minMinimumelongation(%) r90min
n90min
Durezza VickersHerdness(Vickers)
Analisi chimica % (max)Chemicalanalysis
A30 A50 L05,65√50 min max C P S Mn Ti
DC01
ricottoanneled A 270-390 28 30 32 - - - 105
0,120 0,045 0,045 0,600 -
skinp. LC max280 270-410 28 30 32 - - - 115
incruditihard
C290 200-380 290-430 18 20 24 - - 95 125
C340 min250 340-490 - - - - - 105 155
C390 min210 390-540 - - - - - 117 172
C440 min360 440-590 - - - - - 135 185
C490 min420 490-640 - - - - - 155 200
C590 min520 590-740 - - - - - 185 225
C690 min630 min690 - - - - - 215 -
DC03
ricottoanneled A 270-370 24 36 37 - - 100
0,100 0,035 0,035 0,450 -
skinp. LC max240 270-370 34 36 37 1,30 - 110
incruditihard
C290 210-355 290-390 22 24 26 - - 65 117
C340 min240 340-440 - - - - - 105 130
C390 min330 390-490 - - - - - 117 155
C440 min380 440-540 - - - - - 135 172
C490 min440 490-590 - - - - - 155 185
C590 min540 min590 - - - - - 185
DC03
ricottoanneled A 270-350 38 40 40 - - 95
0,080 0,030 0,030 0,400 -
skinp. LC max210 270-350 38 40 40 1.60 1,18 105
incruditihard
C290 220-325 290-390 24 26 28 - - 95 117
C340 min240 340-440 - - - - - 105 130
C390 min350 390-490 - - - - - 117 155
C440 min400 440-540 - - - - - 135 172
C490 min460 490-590 - - - - - 155 185
C590 min560 590-690 - - - - - 185 215
DC05 skinp. LC max180 270-330 40 42 42 1,9 0,20 - 100 0,060 0,025 0,025 0,035 -
r min n min
DC06 skinp. LC max180 270-350 38 40 40 1-8 0-22 - - 0,020 0,020 0,020 0,250 0,30
Nastri e bandelle rilaminati a freddo stretti Cold rolled, strips and sheets metal
LAMIERE DA COILS
33 34
Proprietà tecnologiche e magnetiche - Tecnological and magnetical properties
Designazione secondo
Designationaccording
Spessore nominaleNominalthickness
Perdite totali specifiche massime
Max.specifictotallosses
Polarizz. magnetica min. (T) in campo magnetico alternato per una intensità di
campo magnetico (in A/m) pari a 1) 2)
Min.magneticpolarization(T)inalternatemagneticfieldwithafieldintensity(inA/m)equalto
Massa volumica convenzionaleConventionalmass
volume
EN 10027-1
EN 10027-2 MM (W/kg) a 50 Hz
per 1,5 T1) 2500 5000 10000 (kg/dm3)
M660-50D 1.0361 6,06 1,62 1,70 1,79 7,85
M890-50D 1.0362 0,50 8,9 1,60 1,68 1,78 7,85
M1050-50D 1.0363 10,50 1,57 1,65 1,77 7,85
M660-50D 1.0364 8,00 1,62 1,70 1,79 7,85
M660-65D 1.0365 0,65 10,00 1,60 1,68 1,78 7,85
M660-65D 1.0366 12,00 1,57 1,65 1,77 7,85
Designazione secondoDesignationaccording
Perdite totali specifiche massimeMax.specifictotallosses Fattore di laminazione
RollingrateEN 10027-1 EN 10027-2 (W/kg) a 1,0 T a 50 Hz (W/kg) a 1,5 T a 60 Hz
M660-50D 1.0361 2,80 8,38 0,97
M890-50D 1.0362 3,70 11,30 0,97
M1050-50D 1.0363 4,30 13,34 0,97
M660-50D 1.0364 3,30 10,16 0,97
M660-65D 1.0365 4,20 12,70 0,97
M660-65D 1.0366 5,00 15,24 0,97
Lamiere e nastri magnetici di acciaio non legato, laminati a freddo e forniti allo stato semifinitoCold rolled electrical non-alloyed steel sheet and strip delivered in the semi-processed state
1) Questi valori sono validi solo per provette allo stato di riferimento,2) Da diversi anni è consuetudine indicare dei valori di densità di flusso magnetico. In effetti l'apparecchio Epstein determina la polarizzazione magnetica (induzione intrinseca), che è definita dalla seguente relazione:J= G µ0Hdove:J = polarizzazioneB = induzione magneticaµ0 = costante magnetica: 4 π 10-7 H-m-1
H = intensità di campo magnetico in conformità alla IEC (121)
1) The indicated figures are vaiid only for specimen in the conditions2) It has been usage for many years to indicate vauies of magnetic density, although the Epstein instrument reads the magnetic polarization (intrinsic induction) determined by the following equation:J= G µ0Hwhere'J = polarizationB = magnetic inductionµ0=magneticconstant:4π10
-7 H-m-1
H = magnetic field intensity according to IEC 121
Prodotti piani laminati a freddo di acciai microlegati ad alto limite di snerva mento per formatura a freddoCold-rolled flat products made of high yield strength micro-alloyed steels for cold forming
Composizione chimica all'analisi di colata - Cast analysis
Designazione dell'acciaio
Steel-designationComposizione chimica in % di massa-Chemicalcomposition(%bymass)
SimbolicaName
NumericaNumber
C %max
Si %max
Mn %max
P %max
S %max
Al %max
No %max
Ti %max
H 240 LA 1.0480 0,10 0,50 0,60 0,025 0,025 0,015 0,090 0,15
H 280 LA 1.0489 0,10 0,50 0,50 0,025 0,025 0,015 0,090 0,15
H 320 LA 1.0548 0,10 0,50 1,00 0,025 0,025 0,015 0,090 0,15
H 360 LA 1.0550 0,10 0,50 1,20 0,025 0,025 0,015 0,090 0,15
H 400 LA 1.0556 0,10 0,50 1,40 0,025 0,025 0,015 0,090 0,15
Caratteristiche meccaniche - Mechanical charateristics
Designazionedell'acciaio
Steel-designation
Reh1) N/mm2
Rm N/mm
minA % min Diametro min.
piegamento a 180°
Min.bendingradium180°
Min.longitudin.
Min.longitudinal
Max L0 = 80 L0 = 50
SimbolicaName
NumericaNumber
LongitudinaleLongitudinal
TrasversaleTrasversal
LongitudinaleLongitudinal
LongitudinaleLongitudinal
LongitudinaleLongitudinal
H 240 LA 1.0480 240 310 330 340 27
L0 80+
2 %
0e
H 280 LA 1.0489 280 360 380 370 24 0e
H 320 LA 1.0548 320 410 440 400 22 0e
H 360 LA 1.0550 360 460 500 430 20 0,5e
H 400 LA 1.0556 400 500 540 460 18 0,5e
1) Mediante accordo all'atto della richiesta d'offerta e dell'ordinazione possono essere forniti prodotti con tenore di zolfo all'analisi su prodotto" 0,012%2) Questi elementi aggiuntivi possono essere utilizzati soli oppure in combinazione, quando essi figurano nella definizione dell'acciaio entro i limiti di composizione indicati Può essere utilizzato anche il vanadio. La somma dei tenori di questi tre elementi dispersoidi non deve tuttavia risultare maggiore dello 0,22%.
1) Products with sulphur content , 0,012% (chemical composition on finished product) may be supplied upon specification at the time of inquiry and arder)2) These additional elements may be present either individually or at the same time when included in the chemical composition of the steel grade and when staying whithin the related limits Vanadium may be also present The sum of these three dispersoidal elements shall not exceed 022%
1) Se non si manifesta il fenomeno dello snervamento deve essere determinato il carico unitario di scostamento dalla proporzionalità 0,2% (Rpo.2J.2) A titolo indicativo1) In case of no yielding point shuold occur, the conventionallimit of elasticity 02% (RpO2) shall be determined2) Indicative
LAMIERE DA COILS
35 36
Tolleranze dimensionali Nastri a freddo strettiDimensional tolerances - Cold rolled narrow strips
Tolleranze di spessore EN 10140 - Thickness tolerances EN 10140
Spessorinominali
Nominalthickness
Vale per larghezze del nastroOnlyforstripwidth
< 125 mm
Vale per larghezze del nastroOnlyforstripwidth
≥ 125 mm < 250 mm
Vale per larghezze del nastroOnlyforstripwidth
≥ 250 mm < 600 mmvariazione normale
standardtolerance
variazione precisione
(P)precisionvarietion
variazione fine (F)
finevariation
variazione normale
standardtolerance
variazione precisione
(P)precisionvarietion
variazione fine (F)
finevariation
variazione normale
standardtolerance
variazione precisione
(P)precisionvarietion
variazione fine (F)
finevariation
≥ <
0,25 0,40 ± 0,020 ± 0,015 ± 010 ± 0,025 ± 0,020 ± 0,015 ± 0,030 ± 0,020 ± 0,0150,40 0,60 ± 0,025 ± 0,020 ± 0.015 ± 0,030 ± 0,025 ± 0,015 ± 0,035 ± 0,025 ± 0,020
0,60 1,00 ± 0,030 ± 0,025 ± 0.015 ± 0,035 ± 0,030 ± 0,020 ± 0,040 ± 0,030 ± 0,025
1,00 1,50 ± 0,035 ± 0,030 ± 0.020 ± 0,040 ± 0,035 ± 0,025 ± 0,050 ± 0,040 ± 0,0301,50 250 ± 0,045 ± 0,035 ± 0.025 ± 0,050 ± 0,040 ± 0,030 ± 0,060 ± 0,045 ± 0,0352,50 4,00 ± 0,055 ± 0,040 ± 0.030 ± 0,060 ± 0,050 ± 0,035 ± 0,075 ± 0,055 ± 0,040
Tolleranze sulla larghezza EN 10140 - Width tolerances EN 10140
Spessori nominaliNominalthickness Larghezze nominali dei nastri Stripstandardtolerances
≥ < < 125 ≥ 125 < 250 ≥ 250 < 600≥ 350 < 600 mmsolo MarcegagliaMarcegagliaonly
0,25 4,00 - - - - 0 +2Nastri non refilati (NK)
secondo fatt. MMmilledgestrip(NK)
acc.NKfactor
0,60 1,00 ± 0,15 ± 0,10 ± 0,20 ± 0,13 ± 0,25 ± 0,18 -
nastri refilati (NK)slit to width strip (GK)
1,00 1,50 ± 0,20 ± 0,13 ± 0,20 ± 0,18 ± 0,30 ± 0,20 -
1,50 2,50 ± 0,25 ± 0,18 ± 0,30 ± 0,20 ± 0,35 ± 0,25 -
2,50 4,00 ± 0,30 ± 0,20 ± 0,35 ± 0,25 ± 0,40 ± 0,30 -
Tolleranze sulla larghezza EN 10140 - Width tolerances EN 10140
Larghezze nominali dei nastri Stripstandardtolerances
Tolleranze normaliNormaltolerances
Tolleranze ristretteLimitedtolerances
≥ < mm mm10 25 5 225 40 3,50 1,50
40 125 2,50 1,25
125 400 2 1
Tolleranze dimensionali Piani zincatiDimensional tolerances
Impiego stampaggio - Use for pressing
Tolleranze sullo spessore EN 10143 - Tolerances on thickness according to standard EN 10143
Tolleranze normali Normaltolerances Tolleranze ristrette Limitedtolerances
Spessori nominaliNominalthickness ≤ 1200 > 1200
≤ 1500 > 1500 ≤ 1200 > 1200≤ 1500 > 1500
≤ 0,4 ± 0,05 ± 0,06 - ± 0,03 ± 0,04 -
> 0,4 ≤ 0,6 ± 0,06 ± 0,07 ± 0,08 ± 0,04 ± 0,05 ± 0,06
> 0,6 ≤ 0,8 ± 0,07 ± 0,08 ± 0,09 ± 0,05 ± 0,06 ± 0,06
> 0,80 ≤ 1,00 ± 0,08 ± 0,09 ± 0,10 ± 0,06 ± 0,07 ± 0,07
> 1,00 ≤ 1,20 ± 0,09 ± 0,10 ± 0,11 ± 0,07 ± 0,08 ± 0,08
> 1,20 ≤ 1,60 ± 0,11 ± 0,12 ± 0,12 ± 0,08 ± 0,09 ± 0,09
> 1,60 ≤ 2,00 ± 0,13 ± 0,14 ± 0,14 ± 0,09 ± 0,10 ± 0,10
> 2,00 ≤ 2,50 ± 0,15 ± 0,16 ± 0,16 ± 0,11 ± 0,12 ± 0,12
> 2,50 ≤ 3,00 ± 0,17 ± 0,18 ± 0,18 ± 0,12 ± 0,13 ± 0,13
LAMIERE DA COILS
37 38
Tolleranze dimensionali Piani zincatiDimensional tolerances - Galvanized flat products
Impiego strutturale - Structural use
Tolleranze sullo spessore EN 10143 - Tolerances on thickness according to standard EN 10143
Tolleranze normali Normaltolerances Tolleranze ristrette Limitedtolerances
Spessore nominaleNominalthickness ≤ 1200 > 1200
≤ 1500 > 1500 ≤ 1200 > 1200≤ 1500 > 1500
≤ 0,4 ± 0,06 ± 0,07 - ± 0,04 ± 0,05 -
> 0,4 ≤ 0,6 ± 0,07 ± 0,08 ± 0,09 ± 0,05 ± 0,06 ± 0,07
> 0,6 ≤ 0,8 ± 0,08 ± 0,09 ± 0,11 ± 0,06 ± 0,07 ± 0,07
> 0,80 ≤ 1,00 ± 0,09 ± 0,11 ± 0,12 ± 0,07 ± 0,08 ± 0,08
> 1,00 ≤ 1,20 ± 0,11 ± 0,12 ± 0,13 ± 0,08 ± 0,09 ± 0,09
> 1,20 ≤ 1,60 ± 0,13 ± 0,14 ± 0,14 ± 0,09 ± 0,11 ± 0,11
> 1,60 ≤ 2,00 ± 0,15 ± 0,17 ± 0,17 ± 0,11 ± 0,12 ± 0,12
> 2,00 ≤ 2,50 ± 0,18 ± 0,19 ± 0,19 ± 0,13 ± 0,14 ± 0,14
> 2,50 ≤ 3,00 ± 0,20 ± 0,21 ± 0,21 ± 0,14 ± 0,15 ± 0,15
Tolleranze sulla larghezza secondo EN 10143 per coilsWidth tolerances according to EN 10143 for coils
Larghezza nominaleNominalwidth
Tolleranze normaliNormaltolerances
Tolleranze ristretteLimitedtolerances
Negativa-Negative Positiva-Positive Negativa-Negative Positiva-Positive
≤ 600 ≤ 1200 0 + 5 0 + 2> 1200 ≤ 1500 0 + 6 0 + 2
> 1500 0 + 7 0 + 3
Tolleranze sullo spessore EN 10143 - Tolerances on thickness according to standard EN 10143
Classedi tolleranza
Tolerancesofclass
Spessorenominale
Nominalthickness
Larghezza nominale - Nominalwidth
≤ 1200 ≤ 1200 ≤ 1200 ≤ 1200- + - + - + - +
normalestandard
< 0,6 0 + 0,4 0 + 0,5 0 + 0,7 0 + 1,0≥ 0,6 < 0,1 0 + 0,5 0 + 0,6 0 + 0,9 0 + 1,0≥ 1,0 < 2,0 0 + 0,6 0 + 0,8 0 + 1,1 0 + 1,4
≥ 2,0 ≤ 3,0 0 + 0,7 0 + 1,0 0 + 1,3 0 + 1,6
ristretta (s)limited
< 0,6 0 + 0,2 0 + 0,2 0 + 0,3 0 + 0,5≥ 0,6 < 0,1 0 + 0,2 0 + 0,3 0 + 0,4 0 + 0,6≥ 1,0 < 2,0 0 + 0,3 0 + 0,4 0 + 0,5 0 + 0,7≥ 2,0 ≤ 3,0 0 + 0,4 0 + 0,5 0 + 0,6 0 + 0,8
Tolleranze dimensionali Piani zincati Dimensional tolerances - Galvanized flat products
Tolleranze sulla larghezza per i prodotti spianati - Lenght tolerance for flattered products
Larghezza nominale
Nominalwidth
Tolleranze normali - Normaltolerances Tolleranze ristrette - Limitedtolerances
Negativa-Negative Positiva-Positive Negativa-Negative Positiva-Positive
< 2000 mm 0 6 0 3
≤ 2000 mm 0 0,003 x l 0 0,0015 x l
Tolleranza slaa planarità - Tolerance on planarity
Tolleranza sulla planarità per prodotti con snervamento < 280/Nmm2 Toleranceonplanarityofproductswithyieldstrenght<280N/mm2
Classedi tolleranza
Tolerancesofclass
Larghezza nominaleNominalwidth
Spessore nominale - Nominalthickness
< 0,7 mm ≥ 0,7 ≤ 1,2 ≥ 1200
- + -
Tolleranzanormale
Standardtolerance
≤ 600 ≤ 1200 12 10 8
> 1200 ≤ 1500 15 12 10
> 1500 19 17 15
Tolleranzaristretta
Limitedtolerance
≤ 600 ≤ 1200 5 4 3
> 1200 ≤ 1500 6 5 4
> 1500 8 7 6
Tolleranza slaa planarità - Tolerance on planarity
Tolleranza sulla planarità per prodotti con snervamento ≥ 280 e < 360 N/mm2 Toleranceonplanarityofproductswithyieldstrenght≥280and<360N/mm2
Classedi tolleranza
Tolerancesofclass
Larghezza nominaleNominalwidth
Spessore nominale - Nominalthickness
< 0,7 mm ≥ 0,7 ≤ 1,2 ≥ 1200
- + -
Tolleranzanormale
Standardtolerance
≤ 600 ≤ 1200 15 13 10
> 1200 ≤ 1500 18 15 13
> 1500 22 20 19
Tolleranzaristretta
Limitedtolerance
≤ 600 ≤ 1200 8 6 5
> 1200 ≤ 1500 9 8 6
> 1500 12 10 9
LAMIERE DA COILS
39 40
Caratteristiche meccaniche EN 10142 -MachanicalstandardEN1042
Qualità - Quality Caratteristiche meccaniche -Mechanicalcaracteristics
EN 10027-1 EN 10027-2 Impiego -UseSnervamento Re
max N/mm2
Yieldpoint
Resistenza Re max N/mm2
Resistance
Allungamento A80 minElongation
DX1D+Z en 101421990
Piegatura profilaturaBending profiling
Fe E 275 TM Fe E 275 TM Fe E 275 TM
DX1D+Z FeP02G StampaggioForming
- - -
DX1D+Z FeP03G Stampaggio profondoDeep forming
Fe E 355 TM Fe E 355 TM Fe E 355 TM
DX1D+Z FeP06G(*) Stampaggio extra profondoExtra-deep forming
Fe E 355 TM Fe E 355 TM Fe E 355 TM
Caratteristiche meccaniche EN 10147 -MachanicalstandardEN1047
Definizioni-Definitions Caratteristiche meccaniche-Mechanicalcharateristics
nuova qualitànewquality
vecchia qualitàoldquality
ImpiegoUse
SnervamentoYieldpoint
Resistenza Rm max N/mm2
Resistance
Allungamento A80 minElongation
S220 GD+Z FeE 220G Strutturale - Structural 220 330 20
S250 GD+Z FeE 250G Strutturale - Structural 250 330 19
S280 GD+Z FeE 280G Strutturale - Structural 280 360 18
S320 GD+Z FeE 320G Strutturale - Structural 320 390 17
S350 GD+Z FeE 350 G Strutturale - Structural 350 420 16
S350 GD+Z FeE 550G Strutturale - Structural 550 560 -
Coils e nastri zincati a caldo (Sendzimir)Hot dip galvanised coils and strips (Sendzimir)
Impiego per profilatura e/o stampaggioUse for profiling and/or pressing
Impiego strutturaleStructural use
(*) per i nastri ottenuti sul nostro impianto queste qualità sono in fase sperimentale, la fattibilità va sempre richiesta preventivamente.
(*) for the strips obtained on our system, these qualities are in an experimental phase, feasibility should always ba requested beforehand.
Qualità speciali Special quality
Tabella di comparazione tra le normative in vigore e le precedenti norme europee ed extraeuropeeComparisontablebetweenstandardsinforceandpreviousEuropeanandExtra-Europeanstandards
EN 10147-97 EN 10147-91 AF NORM 36-321 DIN 17162 T1 BS 2989 ISO 3575 JIS 3302 ASTM
DXS1D+Z FE P02 G GC II 02 Z Z 2 02 SGCC A 526
DX51D+Z FE P03 G GE III 03 Z Z 3 03 SGCH A 527
DX51D+Z FE P05 G GS V 04 Z Z 5 04 - -
DX51D+Z FE P06 G - 05 Z Z 6 05 SGD1 A 528
- - - - - - SGD2 A 642
- - - - - - SGD3 -
EN 10147-97 EN 10147-91 DIN 17162 T1 ISO 3575 JIS 3302 ASTM
10 FE E 220 G - - - 220 - -
25 FE E 250 G - ST E 250.2Z - 250 SGC340 A
40 FE E 280 G - ST E 280.2Z - 280 - B
125 FE E 320 G - ST E 320.2Z/3Z
- 320 SGC400 C
40 FE E 350 G - ST E 350.3Z - - SGC440 D
125 - - - - - SGC490 F
125 FE E 550 G - - - - SGC570 E
La norma DIN 17162T1 prevedeva anche la qualità 01Z senza alcuna garanzia di caratteristiche meccaniche.
The DIN 17162T1 standard a/so encompasses the 01Z for strips wider than 600 mm.
LAMIERE DA COILS
41 42
Finiture superficiali per i nastri zincatiSurface finishes
I nastri zincati possono avere diversi aspetti superficiali, ovvero la stellatura dello zinco può as."umere varie forme e dimensioni, come di seguito indicato:
Definizione della stellatura:• Stellatura normale (N) , è il risultato della solidificazione normale dello zinco (per quanto
riguarda specificatamente il nostro impianto con aggiunta di antimonio), Le stellature possono avere pezzatura variabile e/o colorazioni eterogenee, Questi elementi non influiscono sulla qualità del rivestimento.
• Stellatura ridotta (M), il bagno di zinco viene alleggerito di antimonio ed il raffreddamento viene tenuto sotto controllo in modo da ridurre al massimo le dimensioni dei poligoni di zinco superficiale. Va ordinata appositamente.
• Rivestimento di lega ferro-zinco (R), questo rivestimento ottenuto mediante trattamento termico di diffusione del ferro nello zinco, presenta un aspetto omogeneo grigio opaco. (l)
Protezione della superficie:La protezione superficiale ha 10 scopo di inibire la formazione dell'ossido bianco di zinco durante le fasi di trasporto e di magazzinaggio causata dall'umidità. I possibili trattamenti sono:• Passivazione chimica (C), la superficie viene trattata con acido cromico, sono possibili tratti di
nastro con residui giallastri che non pregiudicano la qualità del prodotto. Questo trattamento è quel10 che viene dato sempre su tutto il nastro che esce direttamente dalla linea di zincatura.
• Oliatura (O), la superficie viene protetta con olio sgrassabile. Questo trattamento viene fatto sempre su tutto il nastro che subisce una skinpassatura fuori linea, nastri skinpassati lucidi (produzione guide) o nastri skinpassati ruvidi in P0SG.
• Passivazione chimica e oliatura (CO), è possibile solo previo accordo specifico in fase di ordine. (l).• Stato non trattato, ovvero non protetto ne con passivazione o oleatura (U), sempre solo su esplicita
richiesta. Naturalmente l'acquirente si deve fare carico di eventuali ossidazioni del prodotto.
Aspetti superficiali:• Superficie normale (A), sono ammesse imperfezioni tipo: piccoli alveoli, variazioni del
grado di stellatura, macchie nere, leggere graffiature e leggere macchie di passivazione.• Superficie migliorata (E), è ottenuto mediante laminazione (skinpassatura) superficiale a
freddo, sono ammesse imperfezioni tipo: graffi della skinpassatura, impronte di cilindri, irregolarità, striature. Non sono ammesse cavità.
• Superficie di qualità superiore (C) , è ottenuto mediante laminazione (skinpassatura) superficiale a freddo, la superficie migliore non deve in alcun caso alterare l'aspetto uniforme di una verniciatura di alta qualità. L'altra superficie deve presentare caratteristiche corrispondenti almeno alla superficie di tipo (E).
• Secondo fattibilità Marcegaglia, abbiamo la possibilità di foroire altri tipi di finiture superficiali, oltre quella prevista dalla norma, mediante passaggi di skinpassatura, si tratta di varianti della finitura (E) ed i codici previsti sono i seguenti:- EI, liscia normale, solo con protezione tipo "C"- E2, liscia brillante, solo con protezione tipo "O"- E3, skinpassata ruvida normale, solo con protezione tipo "C"- E4, skinpassatura ruvida controllata, solo con protezione tipo "0"
I nastri che vengono skinpassati fuori linea di norma vengono oleati per consentire la protezione. Nel caso venga richiesto espressamente nastro non oleato, potrebbero verificarsi processi di ossido bianco di zinco in funzione di stoccaggi prolungati e/o condizioni atmosferiche particolari. In questo caso Marcegaglia non si assume responsabilità per i danneggiamenti. La differenza di aspetto superficiale tra la fir1itura (E) e (C) è la stessa che abbiamo sul nastro a freddo tra la finitura MA e ME, ovvero riguarda solo l'accettazione o meno di difetti superficiali.
(1) queste prescrizioni non sono fattibili sul nostro . impianto, possono però essere richieste ad un fornitore esterno.
Lamiere e nastri zincati in continuo di acciaio ad alto limite di snervamento per stampaggio a freddoContinuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming - Technical delivery conditions
Analisi chimica (colata) - Chemical composition (cast analysis)
Designazione - Designation % in massa-%bymass
Qualità acciaioSteelgrade
Simboli del tipodi rivestimento
a caldo disponibileSymbolsforthetype
oftheavilable
Cmax
Simax
Mnmin
Pmax
Smax
Almin
Tibmax
NbB
maxNomeName
Numero Number
H180YD 1.0921 +Z, +ZF, +ZA, +AZ, +AS 0,01 0,10 0,70 0,06 0,025 0,02 0,12 -H180BD 1.354 +Z, +ZF, +ZA, +AZ, +AS 0,04 0,50 0,70 0,06 0,025 0,02 - -
H220YD 1.0923 +Z, +ZF, +ZA, +AZ, +AS 0,01 0,10 0,90 0,08 0,025 0,02 0,12 -H220PD 1.0358 +Z, +ZF, +ZA, +AZ, +ASH220BD 1.0353 +Z, +ZF, +ZA, +AZ, +AS 0,06 0,50 0,70 0,08 0,025 0,02 - -
H260YD 1.0926 +Z, +ZF, +ZA, +AZ, +AS 0,01 0,10 1,60 0,10 0,025 0,02 0,12 -H260PD 1.0431 +Z, +ZF, +ZA, +AZ, +ASH260BD 1.0433 +Z, +ZF, +ZA, +AZ, +AS 0,08 0,50 0,70 0,10 0,025 0,02 - -H260LAD 1.0929 +Z, +ZF, +ZA, +AZ, +AS 0,10 0,50 0,60 0,025 0,025 0,015 0,15 0,09
H300PD 1.0443 +Z, +ZF, +ZA, +AZ, +ASH300BD 1.0445 +Z, +ZF, +ZA, +AZ, +AS 0,10 0,50 0,70 0,12 0,025 0,02 - -H300LAD 1.0932 +Z, +ZF, +ZA, +AZ, +AS 0,10 0,50 1,00 0,025 0,025 0,015 0,15 0,09
H340LAD 1.0933 +Z, +ZF, +ZA, +AZ, +AS 0,10 0,50 1,00 0,025 0,025 0,015 0,15 0,09H38LAD 1.0934 +Z, +ZF, +ZA, +AZ, +AS 0,10 0,50 1,40 0,025 0,025 0,015 0,15 0,09
H420LAD 1.0935 +Z, +ZF, +ZA, +AZ, +AS 0,10 0,50 1,40 0,025 0,025 0,015 0,15 0,09
a. H prodotti piani laminati a freddo ad alta resistenza per formatura a freddo; nnn forza minima della prova di trazione, Rp0,2 N/mm2; B bake-hardened; P rifosforato; Y interstitial free; LA micro-legato; D destinato a rivestimento per immersione a caldo
b. Questi elementi aggiuntivi possono essere impiegati singolarmente o in combinazione là dove compaiono nella definizione dell'acciaio indicata dai valori limite dell'analisi chimica. Possono essere aggiunti anche vanadio e boro. Tuttavia la somma delle percentuali di questi 4 elementi disperoidal non deve superare lo 0,22% Anche gli acciai Bake-hardening e gli acciai rifosforati possono contenere questi 4 elementi fino a una percentuale massima dello 0,22% in massa.
a. H cold rolled flat products of high strength for cold forming; nnn minimum proof strength, Rp0,2 N/mm2.
b. B bake-hardened; p rephosphorized; y interstitiell free; LA low alloy (micro.alloyed); D intended for hot-dip coating.
c. These additional elements may be used individually or in combination where they appear in the definition of the steel the composition limits indicated Vanadium and boron may also be added. The sum of the contents of these 4 disperoidal elements shall not exceed 0,22% however.
d. Bake-hardening steels and rephosphorized steels may aiso contain these 4 elements up to max 0,22% by mass.
LAMIERE DA COILS
43 44
Nastri rivestiti di alluminio (alluminiati)Strips coated with aluminium (aluminised)
Caratteristiche meccaniche secondo UNI EU 154 -MechanicalcharacteristicsaccordingtonormUNIEU154
Designazioneconvenzionale
Conventionaleselection
Designazionedella qualitàQualityselection
ResistenzaRm max N/mm2
Maxtensilestrenght
Snervamentomax N/mm2
Maxyieldstrenght
Allungamento minMinelongation
DX51D+AS commercialecommerciale
500 - 22
DX52D+AS stampaggioforming
420 300 26
DX53D+AS stamp. profondodeep forming
380 360 30
DX54D+AS stamp. profondodeep forming
360 220 34
DX55D+AS 370 240 32
Nastri AluzincAluzinc Strips "Aluzinc"
Caratteristiche meccaniche per nastri da stampaggio -Mechanicalcharacteristicsstandardforstripsforpressing
Qualità - Quality Caratteristiche meccaniche - Mechanicalcharacteristics
EN 10142 1995 Cod. qualitàQualitycode
ImpiegoUse
SnervamentoRe max N/mm2
Yieldpoint
ResistenzaRm max N/mm2
Resistance
Allungamento A80 minElongation
DX51D+AZ 1.0226 Piegatura ProfilaturaBending profiling
Non previstoNot requested 500 22
DX52D+AZ 1.0350 StampaggioForming 300(1) 420 26
DX53D+AZ 1.0355 Stamp. profondoDeep forming 260 380 30
DX54D+AZ 1.0306 Stamp. extra profondoExtra-deep forming 220 350 36
Caratteristiche meccaniche per nastri per impiego strutturaleMechanicalcharacteristicsforstripsforstructuralapplications
Qualità - Quality Caratteristiche meccaniche - Mechanicalcharacteristics
EN 10142 1995 Cod. qualitàQualitycode
ImpiegoUse
SnervamentoRe max N/mm2
Yieldpoint
ResistenzaRm max N/mm2
Resistance
Allungamento A80 minElongation
S250GD+AZ 1.0242 strutturale - structural 250 330 19
S280GD+AZ 1.0244 strutturale - structural 280 360 18
S320GD+AZ 1.0250 strutturale - structural 320 390 17
S350GD+AZ 1.0529 strutturale - structural 350 420 16
S550GD+AZ 1.0531 strutturale - structural 550 560 Non previstoNot requested
Il nastro Aluzinc viene prodotto con un procedimento analogo allo zincato tranne per il rivestimento che è composto da una lega di Alluminio (AI 55%) , Zinco (Zn 43,4%) e Silicio (Si 1,6%). L'aspetto superficiale presenta sempre una stellatura anche se molto più ridotta come dimensioni rispetto allo zincato.
The Aluzinc strip is produced with an analogous procedure as that for galvanised strip, except the coating which is comprised of an alloy of Alumininm (AI 55%), Zinc (Zn 43.4%) and Silicon (Si 1.6%). The surface apperance always has a stellar structure even though it dimensions are very much smaller than those on galvanised strip.
Recommended