View
221
Download
0
Category
Preview:
Citation preview
8/14/2019 JR PCI NTv8 User Manual
1/85
8/14/2019 JR PCI NTv8 User Manual
2/85
Juzt-Reboot System/Data Recovery Card
2
Contents:1. Introduction .................................................................42. Operating System Support ..............................................43. System Requirements .....................................................44. Juzt-Reboot Card...........................................................55. Pre-Installation Procedures .............................................56. Install Juzt-Reboot Card ................................................77. Install Software Driver......................................................88. Express Installation .........................................................99. Reserve C Installation....................................................1210. Advanced Installation.....................................................13
10.1 Installing Operating Systems ..............................14
11. Juzt-Reboot
Startup Screen.........................................1511.1 Instant Restoration mode....................................1611.2 Backup Restoration mode...................................1611.3 No Restoration mode ..........................................17
12. Configuration ...............................................................1712.1 Options ...............................................................1812.2 Disk Setup ..........................................................2012.3 Multi-Boot............................................................2412.4 CMOS Tool .........................................................2412.5 Hard Disk Copy...................................................2512.6 Net-Clone............................................................2612.7 Set Open Mode...................................................2612.8 Upgrade ..............................................................2712.9 Uninstall ..............................................................2812.10 About ...............................................................2912.11 Exit ...............................................................29
13. Space Utility ...............................................................2914. Using Juzt-Reboot .......................................................3015. Using Net-Clone ............................................................31
15.1. Net-Clone Setup .................................................3315.2. Receiving............................................................34
15.3. Sending...............................................................3415.3.1 Send Data ................................................3715.3.2 Select Partition to Send ..............................3815.3.3 Send Command ........................................38
15.4 Wake Up On LAN ...............................................3915.5 Net-Clone with Packet Driver..............................40
16. FAQs ...............................................................4216.1. General FAQs.....................................................4216.2. Installation FAQs ................................................4516.3. Hard Disk Copy FAQs.........................................4816.4. Network FAQs.....................................................50
8/14/2019 JR PCI NTv8 User Manual
3/85
Juzt-Reboot System/Data Recovery Card
3
S. Supplemental Information..............................................52S1 Changing Windows Swap File Location..............52
S1.1 Changing Swap File Location in Windows 98 ..52
S1.2 Changing Swap File Location in Windows XP .54S2 Changing My Documents folder location ..........56S2.1 Changing folder location in Windows 98 .........57S2.2 Changing folder location in Windows XP ........58
S3 Changing Outlook Express store location ...........60S4 Multi-OS Installation............................................63S5 Red Hat Linux Installation Procedure..................65
8/14/2019 JR PCI NTv8 User Manual
4/85
Juzt-Reboot System/Data Recovery Card
4
1. IntroductionJuzt-Reboot Card can restore your hard disk drive to itsoriginal setup in just seconds. Even if your data is destroyed byviruses or accidental deletion, Juzt-Reboot Card will recover and restore your system instantly. Problems with your CMOS?Juzt-Reboot Card will not only notify you of a malfunction butalso restores your original CMOS settings. Juzt-Reboot Cards are small PCI interface cards plugged into your computers PCI expansion slot.
2. Operating System SupportJuzt-Reboot supports all known operating systems including
DOS, Windows 3.x, Windows 95/98/ME, WindowsNT/2000/XP/2003, Unix, Xenix, Linux, FreeBSD, etc.
Note:(a) All operating systems are supported with Backup
Restoration and No Restoration mode.(b) MS-DOS, Windows 3.x, and Windows
95/98/ME/NT/2000/XP/2003 operating systems which useFAT16, FAT32 and NTFS file-systems can be supportedwith Instant Restoration mode.
3. System RequirementsJuzt-Reboot does not require high computer specifications.Juzt-Reboot can be installed on any computer even with aPentium processor, but a free PCI slot is required. However, afaster computer is highly recommended. The minimumrequirements are:
IBM PC or compatiblePentium or higher processor
At least 500MB of free HDD space64MB RAMOne free PCI slotColor VGA monitor
8/14/2019 JR PCI NTv8 User Manual
5/85
Juzt-Reboot System/Data Recovery Card
5
4. Juzt-Reboot CardBelow is a sample of a Juzt-Reboot PCI Card:
Juzt-Reboot JR-PCI-NT
Juzt-Reboot Cards are Plug & Play compatible.
Note:(a) Actual card may be slightly different for each hardware
version.(b) Please backup all important data before installing Juzt-
Reboot . You may use floppy disks, ZIP disks, CD-R/RWor a spare HDD for backup.
5. Pre-Installation ProceduresIf you intend to retain your Windows 95/98/ME/NT/2000/XP/2003 installation, please perform these tasks beforeinstalling Juzt-Reboot to ensure trouble free operation:
Step 1. Immediately upon powering on the computer, enter BIOS/CMOS setup and disable all VIRUSPROTECTION and/or VIRUS WARNING settings(usually under BIOS FEATURES SETUP or ADVANCED CMOS SETUP for most BIOS types).Save the BIOS/CMOS settings and exit. This preventsJuzt-Reboot from being detected as a virus by thesystem BIOS.
8/14/2019 JR PCI NTv8 User Manual
6/85
Juzt-Reboot System/Data Recovery Card
6
Note:(a) To enter BIOS/CMOS setup for most computers
press c during POST (P ower On S elf Test).However, certain computers use a different keypress. In this case, refer to the computers User Manual. For example: Compaq uses u , Dell usesm and Acer uses b +a +^ .
(b) For certain BIOS types, the settings describedabove may be slightly different, under a differentcategory/menu and/or use similar descriptions.Please refer to the computers User Manual.
Step 2. Start Windows 95/98/ME/NT/2000/XP/2003.
Step 3. Click Start Programs Accessories System Tools Scandisk to scan your file
system for errors and repair them if found. This is toensure that the file system which Juzt-Reboot willprotect is valid and free of errors. Exit Scandisk whendone.
Note:Before running Scandisk or Disk Defragmenter , it isrecommended to close all running programs (includingthose in the System Tray ), disable all anti-virus ,Active Desktop , Screen Saver , Power Management , Task Scheduler ; delete TemporaryInternet Files , TEMP files; and empty the Recyclebin . This will speed up Scandisk and DiskDefragmenter tasks. In Scandisk , enableAutomatically fix errors .
Step 4. Click Start Programs AccessoriesSystem Tools Disk Defragmenter to defragmentand reorganize your file system more efficiently. Thisis important because Juzt-Reboot requires acontiguous block of free space to allocate the buffer.Please exit Disk Defragmenter when done.
Step 5. Click Start Shut Down . In Shut DownWindows dialog box, select Shut down and clickOK to power off the computer. Proceed to 6. InstallJuzt-Reboot Card .
8/14/2019 JR PCI NTv8 User Manual
7/85
Juzt-Reboot System/Data Recovery Card
7
6. Install Juzt-Reboot CardProcedures for installing Juzt-Reboot Card inside thecomputer:
Step 1. Remove the computers casing cover to access themotherboard. Please make sure the computers power is off.
Note:To ensure the computer's power is off and for better safety, pull out the mains power plug.
Step 2. Find a free PCI expansion slot. Below is a picture of a
typical PCI expansion slot:
Step 3. Insert Juzt-Reboot Card into the empty PCI slot.Please make sure the card is inserted properly.Improper insertion may damage the card and/or causethe computer to hang.
PCI slot
8/14/2019 JR PCI NTv8 User Manual
8/85
Juzt-Reboot System/Data Recovery Card
8
Step 4. Close the computers casing cover.
Step 5. Power on the computer and proceed to 7. Install
Software Driver .
Note:(a) If you are not sure and/or not familiar with these tasks,
please acquire the services of a qualified computer technician.
(b) Removing the computers casing cover may void your computers warranty (i.e. usually a sticker or seal on thecasing). Please check before you proceed.
(c) Before attempting to insert the Card, please touch the
metal casing to discharge any static electricity that you mayhave picked up or generated yourself. This is to preventany damage to the card and/or computer.
7. Install Software Driver Use the following procedures to install Juzt-Reboot Cardssoftware driver:
Step 1. Upon starting the computer, Juzt-Reboot s firstmessage should appear:
Juzt-Reboot HARDWARE:vx.x
Then Juzt-Reboot First Time Installation screen willappear:
Insert Install Disk, Press ENTER to continue ...
Insert Juzt-Reboot Driver and press f to continue.Juzt-Reboot will begin its installation into the HDD.
8/14/2019 JR PCI NTv8 User Manual
9/85
Juzt-Reboot System/Data Recovery Card
9
Step 2. The Install Setup screen will appear:
Use zx cursor keys to select and press f toperform selected installation:
For [Express] installation mode, proceed to8. Express Installation (refer below).
For [Reserve C] installation mode, proceed to9. Reserve C Installation (refer to page 12).
For [Advanced] installation mode, proceed to10. Advanced Installation (refer to page 13).
Note: Selecting [Express] will retain all current partitions.
Selecting [Reserve C] will retain partition C: , butdestroy all other partitions. Selecting [Advanced]will destroy all partitions in the hard disk.
Only systems with existing DOS or Windows OS canbe protected by using Express installation. Please
use Advanced for other OS.
8. Express InstallationFor Express installation mode, all partitions will be retained andall Juzt-Reboot configurations are set up automatically.
Step 1. After selecting [Express] , you will be prompted toselect the buffer size as shown on the following page.
8/14/2019 JR PCI NTv8 User Manual
10/85
Juzt-Reboot System/Data Recovery Card
10
Press f to accept the default size or use the w key tomove up and use the {} keys to select the sizeand accept after finishing. Default size of the buffer isabout 500MB which is the optimum size for mostenvironments. The size can be set from 50MB to themaximum size of about 1000MB .
Step 2. When the message Install completed appears,remove the Juzt-Reboot Driver and press f toreboot.
Step 3. After rebooting, Juzt-Reboot Operating Systemscreen will appear.
Step 4. Press b +f to start up Windows in Supervisor mode. When prompted for the Supervisor Password,press the f key (default password after installation isblank).
8/14/2019 JR PCI NTv8 User Manual
11/85
Juzt-Reboot System/Data Recovery Card
11
Step 5. After Windows has started, insert Juzt-Reboot Driver and click Start Run... . In Run dialog box,type in A:\SETUP as shown below:
Click OK to install Juzt-Reboot 32-bit driver. After setup has completed, restart the computer.
Step 6. When Juzt-Reboot Operating System screenappears again, press u to go into Juzt-Reboot 'sConfiguration menu. A login dialog box will appear
prompting for Supervisor password. Press f for default password.
Step 7. When the Configuration menu appear, select DiskSetup (Refer to 12.2 Disk Setup on page 20).
Step 8. In Disk Setup screen, select the system (drive C:)partition. Press q to switch to Option Setup andensure that the Restore Type is set for Every . If other settings are desired, then set to either Manual ,Daily , Weekly , Monthly , etc.
Step 9. When done, press ^ to save and exit.
Note:The default [Express] installation mode will allocate about500MB for Buffer from drive C: and set Instant Restoration type with Every schedule for drive C: . If you only have onepartition (drive C:), it will also create another partition (driveD:).
8/14/2019 JR PCI NTv8 User Manual
12/85
Juzt-Reboot System/Data Recovery Card
12
9. Reserve C InstallationFor Reserve C installation mode, partition C: will be retained,
but all other partitions in the HDD (including logical drives) willbe destroyed.
Reserve C installation mode will work only if the hard disk hasmore than one partition. Other partitions will be removed, andfree up space to prepare for multi-boot configuration.
For Windows 95/98/ME/NT/2000/XP/2003: This will allocateabout 500MB buffer and set Instant Restoration type withEvery schedule for drive C:.
Step 1. After selecting [Reserve C] , the message Installcompleted will appear. Remove Juzt-Reboot Driver and press f to reboot.
Step 2. After rebooting, Juzt-Reboot Multi-Boot configu-ration screen will appear. Allocate your other OSpartitions (Refer to 12.2 Disk Setup on page 20).
Step 3. After rebooting to the Juzt-Reboot OperatingSystem screen, press b +f to start up Windows inSupervisor mode. When prompted for the Supervisor Password, press the f key (default password after installation is blank).
Step 4. After Windows has started, insert Juzt-Reboot Driver and click Start Run... . In Run dialog box,type in A:\SETUP as shown below:
8/14/2019 JR PCI NTv8 User Manual
13/85
Juzt-Reboot System/Data Recovery Card
13
Click OK to install Juzt-Reboot 32-bit driver. After setup has completed, restart the computer.
Step 5. When Juzt-Reboot Startup screen appears again,press u to go into Juzt-Reboot 's Configurationmenu. A login dialog box will appear prompting for Supervisor password. For first time installation, pressf for default password.
Step 6. When the Configuration menu appears, select DiskSetup (Refer to 12.2 Disk Setup on page 20).
Step 7. In Disk Setup screen, select the system (drive C:)partition. Press q to switch to Option Setup and setthe Restore type . To enable protection, ensure thatit is set to Every , Manual , Daily , etc.
Step 8. When done, press ^ to save and exit.
Step 9. The computer will now reboot. You can start installingoperating systems into each new partition (refer to10.1 Installing Operating Systems on page 14).
Note:The default [Express] installation mode will allocate about500MB for Buffer from drive C: . If you only have one partition(drive C:), it may also create another partition (drive D:).
10. Advanced InstallationFor Advanced installation mode, all partitions in the HDD will bedestroyed, and all configuration have to be done manually.
Step 1. After selecting [Advanced] , a warning box will appear prompting for confirmation. By confirming, all partitionsand data on your hard drive will be destroyed. Pleaseplan carefully before continuing.
8/14/2019 JR PCI NTv8 User Manual
14/85
Juzt-Reboot System/Data Recovery Card
14
Step 2. When confirmed, the Disk Setup screen will appear.Create hard drive partitions and setup Attrib ,Name , Size(MB) , File System , Restore Type ,
Buffer(MB) and Boot Password fields (refer to12.2 Disk Setup on page 20).
Step 3. When Disk Setup is completed, press ^ to saveand exit.
Step 4. The computer will now reboot. From now on, startinstalling operating systems into each partition (refer to10.1 Installing Operating Systems on page 14).
Note:When creating partitions, please plan properly. Once thepartitions have been saved, they cannot be changed anymore.To change or repartition the HDD, you have to reinstallJuzt-Reboot or use Juzt-Reboot Multi-Boot function. 10.1 Installing Operating SystemsFor Instant Restore Boot Partition : You have to boot intoSupervisor mode (press b + f at Juzt-Reboot Startupscreen to install Windows operating system. After completinginstalling Windows operating system, insert Juzt-Reboot
Driver diskette and click Start Run In Run dialog box,type in A:\SETUP as shown in the screen below:
Click OK to install Juzt-Reboot 32-bit driver. After setup hascompleted, restart the computer.
For Backup Restore Boot Partition : After completinginstalling an operating system, perform Backup (press b + Bat Juzt-Reboot Startup screen) to create a backup copy.
To select partition to boot, please refer to 12.1. Options onForce Booting on page 19.
8/14/2019 JR PCI NTv8 User Manual
15/85
Juzt-Reboot System/Data Recovery Card
15
Note:All Shared and Private Data Partitions created must beformatted first before they can be used.
11. Juzt-Reboot Startup ScreenUpon booting, the Juzt-Reboot Startup screen will be shown(refer to screen on following page):
Hotkeys available will depend on the partitions restoration type,as described below:
For Instant Restore Boot Partition:f .................Boot into User mode (for normal use)b +f ........Boot into Supervisor mode (for maintenance)*b +B ........Perform Backup function**b +R ........Perform Restore function***K ................. Keep changes temporarily from previous boot.
For Backup Restore Boot Partition:
f .................Boot partitionb +B ........Perform Backup function**b +R ........Perform Restore function***
For No Restore Boot Partition:f .................Boot partition
Press u to enter Configuration menu* (refer to 12.Configuration on page 17).
8/14/2019 JR PCI NTv8 User Manual
16/85
Juzt-Reboot System/Data Recovery Card
16
Note:* Supervisor password is required.** Backup/Restore password is required.*** Restore password is required.
11.1 Instant Restoration modeThis mode supports FAT16, FAT32 and NTFS file systemsused by DOS and Windows 95/98/ME/NT/2000/XP/2003operating systems. Provides two operating modes:Supervisor and User . Below are descriptions of each mode:
(a) Supervisor ModeAll changes made to this partition are retained. Hence,
there is no protection available.(b) User Mode
Any changes made to this partition are temporary. Whenperforming Restore function (press b + R or accordingto Restore Interval ), all changes will be discarded. TheKeep (press K ) function will retain all changes madeduring the previous session upon rebooting. To retain allchanges in User mode, use the Backup function (pressb + B ).
Note:Before performing a Backup operation, ensure that you areabsolutely sure that the system is clean, that there are noviruses, etc. Once backup is done, any settings, viruses, etcare saved permanently as part of the system.
11.2 Backup Restoration modeThis mode supports all operating systems. To use this feature,you must perform Backup function first after installing your operating system. You may then use the Restore function. You
can Backup as often as you desire. When performing Restore ,it will restore the last Backup partition image.
For first time installation: Press f to boot the partition andproceed to installing your operating system first. When done,reboot and perform Backup function (press b + B ) to savethe partition image into Buffer .
8/14/2019 JR PCI NTv8 User Manual
17/85
Juzt-Reboot System/Data Recovery Card
17
11.3 No Restoration modeThis mode supports all operating systems. As there is noBuffer for restoration purposes, all changes made to thispartition are retained.
12. ConfigurationThe Configuration menu screen is for changing settings andexecute special functions. To enter, press u at Juzt-Reboot Startup screen (Supervisor password required). Refer to thediagram below:
Use wy cursor keys to select and press f . For detailedexplanation of each option, refer to the following:
8/14/2019 JR PCI NTv8 User Manual
18/85
Juzt-Reboot System/Data Recovery Card
18
12.1 OptionsSetup the following options (refer to the diagram below):
Use wy cursor keys to select. Press f to modify eachsetting. For [Password] fields, press f to begin entry. For detailed descriptions of each option, refer to the following:
(a) Boot sequence:BIOS (default) Use BIOS boot sequence.C only(Recommended)
Boot from hard drive C: only. For bestprotection against booting from other
OS and installing over the existingoperating system.A, C Boot from floppy drive A: and if there is
no bootable diskette, then boot fromhard drive C:
(b) Auto restore CMOS data:Disable (default) Does not restore CMOS settings when
CMOS settings are modified.Enable Automatically restores CMOS settings
(with a saved copy) when CMOSsettings are modified.
(c) Safety Value:Normal (default) Normal security levelAdvanced Enhanced security level, for protection
against Low Level Format. Note thatthis results in more stringent checkingof disk access and will slow down thePC.
8/14/2019 JR PCI NTv8 User Manual
19/85
Juzt-Reboot System/Data Recovery Card
19
(d) Display hotkey message:Disable Do not display any hotkeys in Juzt-
Reboot Startup screenEnable (default) Display all hotkeys in Juzt-Reboot
Startup screen.
(e) Show brandname:Disable Do not display Juzt-Reboot logo in
Juzt-Reboot Startup screen.Enable (default) Display Juzt-Reboot logo in Juzt-
Reboot Startup screen.
(f) Force Booting:
Selects a system partition to boot. The Name s of allbootable partitions will be available when pressing { or } . However, if you have selected [Boot Menu] option,then a multi-boot menu will appear for you to select apartition to boot.
(g) Auto select:Automatically boots the selected partition after a predefinednumber of seconds. Minimum is 2 seconds (default) andmaximum is 99 seconds. However, if you have selected[Disable] option, then Juzt-Reboot will wait for the user to select a partition to boot.
(h) Auto power off:Automatically power off the computer after a predefinednumber of minutes. Minimum is 1 minute and maximum is99 minutes. However, if you have selected [Disable] option(default), then Juzt-Reboot will not power off thecomputer. This function works only for computers with ATXpower supply.
(i) Supervisor Password:Password for entering [Configuration] menu (press u ) or booting into Supervisor mode (press b + f ) at Juzt-Reboot Startup screen.
(j) Restore Password:Password for manual Restore function (press b + R )at Juzt-Reboot Startup screen.
8/14/2019 JR PCI NTv8 User Manual
20/85
Juzt-Reboot System/Data Recovery Card
20
(k) Backup Password:Password for manual Backup function (press b + B )at Juzt-Reboot Startup screen.
The maximum length of all passwords is 10 characters.
Note:(a) Before enabling Auto Restore CMOS Settings , you
must execute CMOS Tool first to analyze and save thecurrent CMOS settings.
(b) Setting Safety Value to Advanced may lower hardwarecompatibility and slow down your computer as it scrutinizesall HDD access.
(c) For better security, set the Boot sequence to C only toprevent booting from diskette or CD-ROM. This settingoverrides the BIOS boot sequence.
12.2 Disk SetupJuzt-Reboot Disk Setup is used to easily create and managepartitions. All partitions created are regarded as physical diskswhich enable various operating systems to be installed in asingle hard drive.
Use the wy cursor keys to select each field. Press q toswitch between the partition's Attrib/Name table and OptionsSetup table. Press {} to change the values or settings.For partition Name and Boot Password fields, press f firstto begin entry. For detailed descriptions of each field, refer tothe following:
8/14/2019 JR PCI NTv8 User Manual
21/85
Juzt-Reboot System/Data Recovery Card
21
(a) Attrib
[T] Instant Restoration Boot PartitionThe partition will be restored to its original setupmanually or automatically according to the RestoreType . Restoration will be instant as all changesmade are discarded. For example: if set to Every ,restoration will take place on every reboot, and if set toManual all changes are kept (in the Buffer ) until yourestore manually. The default Buffer size allocated isabout 500MB but can be increased to a maximum of 1004MB. Supports FAT16, FAT32 and NTFS, thusapplies to DOS, Windows 3.x, and Windows95/98/ME/NT/2000/XP/2003 operating systems.
[B] Backup Restoration Boot PartitionThe partition will be restored to its original setupmanually or automatically according to the RestoreType . Before restoration can be done, you have tocreate a backup copy into the Buffer . Backup andrestoration will take time, depending on the size of thepartition. Thus, it is recommended to set the RestoreType to Manual . The Buffer size allocated will be
the same as the partition size. Supports all operatingsystems.
[N] No Restoration Boot PartitionNo restoration is provided for this type of partition.Thus backup and restore functions are unavailable.Therefore, no buffer will be allocated. All changesmade will remain. Supports all operating systems.
[S] Shared Data PartitionFor this partition type, the partition will be visible to all
partitions. Useful for sharing data between differentoperating systems. For FAT16 and FAT32 file system,this data partition can also be manually or automatically cleared ( Auto clr. ) according to theRestore Type .
[P] Private Data PartitionFor this partition type, the partition will only be visibleto the boot partition with the same Name setup. It willnot be visible to other partitions. Useful for data that isexclusive to a particular operating system. For FAT16and FAT32 filesystem, this data partition can also be
8/14/2019 JR PCI NTv8 User Manual
22/85
Juzt-Reboot System/Data Recovery Card
22
manually or automatically cleared ( Auto clr . )according to the Restore Type .
(b) NameName of system/data partition. Maximum length is 10characters. You may enter Windows 98, Windows NT,Win2000, Linux, etc. according to your preferences.
(c) Size(MB)Size of the partition in MB. You can adjust this value. Whenadjusting partition size, the remaining available FreeSpace amount will also be adjusted.
(d) File System
The following table is a guide for file systems and operatingsystems support available:FAT16 MS-DOS, Windows 3.x,
Windows 95/98/ME,Windows NT/2000/XP/2003
FAT32 Windows 95/98/ME, Windows2000/XP/2003
NTFS/HPFS Windows NT/2000/XP/2003OS/2 Boot IBM OS/2Linux/M Linux
Linux/SW Linux (Swap)Linux LinuxFreeBSD FreeBSDExtend Extended MS-DOS partitions
Note:(a) FAT16 supports partitions under 8.4GB, however the
maximum size for a FAT16 partition is 2.1GB.(b) Windows NT 4.0 and Linux boot/system partition
cannot be placed beyond 2.1GB.(c) Extend partition is the same as DOS Extended
partition. You can use FDISK to perform further partitioning.
(d) Linux and FreeBSD are Unix/BSD-based operatingsystems. Thus can be applied to similar operatingsystems such as Unix SVR4, Xenix, MINIX, Solaris,NetBSD, BSD/OS, etc.
8/14/2019 JR PCI NTv8 User Manual
23/85
Juzt-Reboot System/Data Recovery Card
23
(e) Restore TypeRestoration schedule for Instant and Backup Restorationpartitions. Also valid for Share and Private data partitions,
but functions as Auto clear schedule. Options availableare:
Disable Disables restore functionsEvery Restores automatically on
every rebootDaily Restores automatically at first
boot of each dayManual Restoration can only be done
manuallySunday, Monday,Tuesday, Wednesday,Thursday, Friday,Saturday
Restores automatically at firstboot of the specified day of theweek
1st, 2nd, 3rd, 4th, 5th,6th, 7th, 8th, 9th, ~ 31 st
Restores automatically at firstboot of the specified date of month.
(f) Buffer Buffer size for restoration. For Instant Restoration type,the default size is about 500MB and can be adjusted to themaximum size of 1004MB. For Backup Restoration type,the buffer size will be the same as the partition.
(g) Boot PasswordPassword for the selected partition. In Juzt-Reboot Startup screen, you will be prompted for this passwordwhen trying to boot. To remove the password, just clear thepassword entry (empty). Maximum length is 10 characters.
Note:(a) When creating or modifying partitions, please plan
properly. This is because once the partitions have beensaved, they cannot be changed anymore.
(b) When creating a new partition or increasing the buffer size,you must have some free HDD space. If there is no freeHDD space available, then retrieve some free space fromone of the other partitions.
(c) New boot or data partitions created have to beFORMATTED before they can be used.
8/14/2019 JR PCI NTv8 User Manual
24/85
Juzt-Reboot System/Data Recovery Card
24
(d) If the operating system is DOS, Windows 3.x, or Windows95/98/ME or Windows NT/2000/XP/2003, it isrecommended to use Instant Restore Boot Partition .
(e) For Backup Restore Boot Partition , you have toBackup the HDD partition manually before you can usethe Restore function.
(f) It is not recommended to set Restore Type to Every for Backup Restore Boot Partition because every time thecomputer reboots, it will take time for the restore process tocomplete.
(g) Juzt-Reboot supports only the primary HDD. Other HDDs (primary slave, secondary, etc) will not be protected.
(h) Juzt-Reboot supports up to 42 physical partitions in one
HDD.
12.3 Multi-BootDestroys all partitions in the HDD for repartitioning andcreating multi-boot system partitions for different operatingsystems. Refer to the diagram below:
If you select [OK] then all partitions and data in the HDD will bedestroyed. Please think carefully and plan properly before usingthis function.
12.4 CMOS ToolAnalyzes current CMOS data and makes a comparison with asaved copy (in the hard drive) for differences. If you select
[OK] , the computer will restart twice.
8/14/2019 JR PCI NTv8 User Manual
25/85
Juzt-Reboot System/Data Recovery Card
25
Execute this function only when some settings have beenmodified or peripherals have been changed or replaced. If anyCMOS settings are changed, Juzt-Reboot Card will remind
you to restore or backup when rebooting, even if you did notexecute this function manually.
12.5 Hard Disk CopyYou can use this function to clone/duplicate hard disk using IDEcables. Up to three hard disks can be copied simultaneously:
Use wy cursor keys to select and press f to execute. For [ ] check box, press k or f to enable/disable the option.When ready, select [Copy] and press f to start copying,otherwise press ^ to return to the Configuration menu. Thefollowing describes each option:
(a) Parameter & All Partitions (Default)Copies the entire hard disk (all partitions and parameter data).
(b) Parameter Enable this check box to copy the parameter of theselected partition. You have to also execute [PartitionSelect] to select one or more partitions (see below).
(c) PartitionEnable this check box to copy the selected partition andparameters. You have to also execute the [PartitionSelect] option to select one or more partitions (see below).
8/14/2019 JR PCI NTv8 User Manual
26/85
8/14/2019 JR PCI NTv8 User Manual
27/85
Juzt-Reboot System/Data Recovery Card
27
This is most useful for corporations or organizations thatautomatically push updates of their database, software, or antivirus definition updates to the PCs, especially at times after
office hours.
To enable the feature, set Force running Supervisor mode to [Enable] , and set the Start time and End time , where theEnd time must come after the Start time .
12.8 UpgradeUpgrade Juzt-Reboot s software driver. A dialog box with themessage Please insert the disk for upgrade will appear.Insert new Juzt-Reboot Driver and select [OK] to upgrade,otherwise select [Cancel] to abort. After the upgrade has beenloaded, the computer will reboot.
For Windows 95/98/ME/NT/2000/XP/2003: After the computer reboots, enter Supervisor mode and execute A:\SETUP from the new Juzt-Reboot Driver . This will install the newJuzt-Reboot 32-bit driver.
Note:
It is recommended to uninstall or remove the previous Juzt-Reboot 32-bit driver by running A:\UN_SETUP from the oldJuzt-Reboot Driver diskette first. The latest version of thedriver disk does not have the UN_SETUP.EXE file, and usesSETUP.EXE for installation and un-installation.
8/14/2019 JR PCI NTv8 User Manual
28/85
Juzt-Reboot System/Data Recovery Card
28
12.9 UninstallRemoves Juzt-Reboot Software Driver from your computer.A dialog box with the message This will remove theprotection shield from the machine, OK to continue willappear. Select [OK] to remove Juzt-Reboot from thecomputer, otherwise select [Cancel] to abort. After removingJuzt-Reboot Software Driver, you have to power off thecomputer and pull out the Juzt-Reboot card.
For Windows 95/98/ME/NT/2000/XP/2003: It is recommendedto uninstall (in Supervisor mode) Juzt-Reboot 32-bit Driver from the operating system by running A:\UN_SETUP fromJuzt-Reboot Driver first (the latest version of the driver diskdoes not have the UN_SETUP.EXE file, and usesSETUP.EXE for installation and un-installation). However,even if you did not uninstall this driver, the operating system will
not be affected and continue to operate normally.WARNING!!After uninstalling Juzt-Reboot , any partition created withJuzt-Reboot 's Disk Setup function ( Advanced installationmode) will disappear. However, partitions retained by Juzt-Reboot during Express installation will still exist.
8/14/2019 JR PCI NTv8 User Manual
29/85
Juzt-Reboot System/Data Recovery Card
29
12.10 AboutDisplays Juzt-Reboot hardware and software version (asshown on the following page):
Press ^ or f to continue and return to [Configuration]menu screen.
12.11 ExitExits [Configuration] menu screen and returns to Juzt-Reboot Startup screen.
13. Space UtilityThe Space utility is installed together with Juzt-Reboot 's32-bit driver. This utility is located under the Programs menu(created during setup). It displays current operating mode(Supervisor or User ) and Buffer usage (%). Refer to thefollowing screenshots on the following page.
In User (protected) mode: Space will display:
8/14/2019 JR PCI NTv8 User Manual
30/85
Juzt-Reboot System/Data Recovery Card
30
In Supervisor (unprotected) mode: Space will display:
Mode indicates Supervisor or User mode. Free Space indicates the amount of buffer space available in User modeonly. This amount will decrease as more changes in the HDDtake place.
14. Using Juzt-Reboot There are many settings in Juzt-Reboot . But you may ask,which one is the right one to use?. That will depend on your needs and environment. To guide you along, two of the mostcommon settings used are as described below:
(a) Automatic Restore
Partition type is set to Instant Restore Boot Partition with Restore Type set to Every . This setting is usefulfor computers which are constantly accessed by differentusers all the time. Each user may modify the computer'ssystem settings to his/her preferences, install and/or remove applications, etc. Using Automatic Restore , everytime the computer reboots, the system will be restored toits original settings and contents. This is very useful for schools, colleges, universities, training institutes, libraries,Internet access outlets, data entry terminals and networkworkstations. This can also be applied to home, office andindividual users as the system is protected at all times (i.e.every time you restart the computer, the system is alwaysin good order even after it has been corrupted or infectedby viruses). However, you have to move all constantlychanging data (e.g. Folders for Outlook Express e-mails,My Documents , Favorites , etc) to another partition(e.g. logical drive D: , E:, etc) or another HDD.
8/14/2019 JR PCI NTv8 User Manual
31/85
Juzt-Reboot System/Data Recovery Card
31
(b) Manual RestorePartition type is set to Instant Restore Boot Partition with Restore Type set to Manual . This is useful for
computers which are accessed by an individual user. Allchanges will be kept, and the user can Backup thesechanges at any time. Whenever the system fails (due tovirus attack, system corruption, format, FDISK or accidental deletion), the user can always Restore thesystem back to the point where the user last performedBackup . However before performing any backup , makesure your system is in good order and free of viruses. Thisis also useful for experimentation . For example: you caninstall new software to test without worrying about systems
settings changed and/or corruption. If the newly installedsoftware works properly and you want to keep it, thenperform Backup . However if the new software corrupts thesystem and/or you no longer want to keep it, then performRestore . This is very useful for testing software that arenot properly programmed, and/or cannot beinstalled/uninstalled properly.
Note:You can perform Scandisk but please do not try todefragment the HDD in User mode as Juzt-Reboot willreorganize your HDD automatically during Backup .
15. Using Net-CloneAfter selecting Net-Clone from the Configuration menu, thefollowing menu is displayed:
To run Net-Clone, ensure that the following conditions are met:
(a) That all the PCs that are to run Net-Clone has a networkadapter (either built-in on the motherboard, or installed inone of the PCs slots).
(b) That all these PCs have the Juzt-Reboot card installed.(c) That the network card is supported in the list of network
adapters in Net-Clone Setup .
8/14/2019 JR PCI NTv8 User Manual
32/85
Juzt-Reboot System/Data Recovery Card
32
(d) If the network adapter is not in the list, then obtain thelatest LAN-DRV update diskette from your distributor/dealer and upgrade using the Upgrade option
in the Configuration menu (refer to 12.8 Upgrade inpage 27).
(e) If the NIC in use is still not in the list of supported NICseven after updating, then you will have to find the packetdriver for your LAN card and use the DOS version of theNet-Clone utility to perform the Net-Clone (refer to 15.5Using Net-Clone with Packet Driver on page 40).
For Net-Clone operations, there are two types of Net-Clonemode the computer can be set to: the Sending computer, and
the Receiving computers.The Sending computer is the PC which has all the hard diskcontents to be copied from. The Receiving computers (therest of the computers in the network) are the PCs which willreceive the contents from the Sending computer.
After configuration of Network Adapter (refer to 15.1 Net-CloneSetup on page 33), select Run Net-Clone and press f . Ascreen similar to the one below appears:
Use wy cursor keys to select and press f to execute theNet-Clone function. Press | to exit and return to Juzt-RebootTools screen.
8/14/2019 JR PCI NTv8 User Manual
33/85
Juzt-Reboot System/Data Recovery Card
33
Note:For Copying Partition(s): The HDD size on the receivingcomputer(s) must be equal to or greater than the sendingcomputer.
15.1. Net-Clone SetupBefore running Net-Clone, ensure that you have configured thecorrect type of network adapter in the Juzt-Reboot Net-Clone Setup menu.
Use the wy keys to select Net-Clone Setup and press f toconfigure the settings.
Use the wy keys to select Packet Driver field and {}to select the packet driver. Press ^ key to exit and save thesettings.
Below are the descriptions of the other settings:
(a) Auto StandbyEnables automatic detection of any Sending computerson the network during booting or at Juzt-Reboot BootMenu screen. When found, this computer becomes theReceiving computer and the Receiving screen will bedisplayed (refer to 15.2 Receiving on page 34). Options
available are Enable (default) and Disable .(b) Computer Name
Name of this computer when used to login to theSending computer. If the name is blank (empty), theSending computer will show ? in the login table of theSending screen. Maximum length is 5 characters.
8/14/2019 JR PCI NTv8 User Manual
34/85
Juzt-Reboot System/Data Recovery Card
34
(c) Group NameName of the group this computer belongs to. You can usethis to distinguish groups of computers on the network. It
can also be used to select a group which can be allowed tologin to this computer when Sending is used. Maximumlength is 2 characters.
15.2. ReceivingPuts the computer on receiving mode (the computer will waitfor a sending computer on the network). See the screenshotbelow:
At any time, press u to exit and return to Net-Clone screen.
If the receiving computer detects any sending computer, themessage * Waiting for login will change to ID:xx toindicate successful login. When any partition and/or parameter data is being received, a spinning / will appear.
Note:This screen can automatically appear on all receivingcomputers when a sending computer is detected on thenetwork. To enable this feature, go into Net-Clone Setup andset Auto Standby to Enable (refer to 15.1 Net-Clone Setup in page 33).
15.3. SendingPuts the computer into sending mode (the sending computer will try to detect any receiving computers on thenetwork). When executing this function, the Sending screen willbe displayed. See the screenshot on the next page:
8/14/2019 JR PCI NTv8 User Manual
35/85
Juzt-Reboot System/Data Recovery Card
35
In the Sending screen (shown above), a login table will bedisplayed. Each in the login table represents areceiving computer on the network. Any receiving computer detected on the network will show up in the login tableabove as a ? or its Net-Clone name (as assigned in Net-Clone Setup (refer to 15.1. Net-Clone Setup in page 33).
When all receiving computers on the network have logged insuccessfully and are ready, press l to proceed.
After pressing l , the hotkeys will now change. See thescreenshot on the next page:
8/14/2019 JR PCI NTv8 User Manual
36/85
Juzt-Reboot System/Data Recovery Card
36
Use wyzx to move the cursor in the login table. Press u toexit and return to Net-Clone screen.
For detailed description of l , m , + and - hotkey functions,see below:
l : Send dataSends partition and parameter data to Receiving
computers on LAN. Refer to 15.3.1 Send Data on thefollowing page.
m : Send commandSends command to Receiving computers on LAN. Refer to 15.3.3 Send Command on page 38.
+- : DelayIncrease/decrease the transmission delay of the networkcard for best performance. Press + to increase and - todecrease the Delay value. If the default value runs
normally, then please do not adjust.To proceed with Sending the data to the other PCs, refer to15.3.1 Send Data on the following page.
8/14/2019 JR PCI NTv8 User Manual
37/85
Juzt-Reboot System/Data Recovery Card
37
15.3.1 Send DataSends partition and/or parameter data to Receiving computers on LAN. See the screenshot below:
Use wy cursor keys to select and press f to start sending.Press | to exit and return to Sending screen. For descriptionof each command, see below:
(a) < Parameter data and all Partitions >Copies all Juzt-Reboot data (including configurationdata) and all partitions to Receiving computers.
(b) < Parameter data >Copies all Juzt-Reboot data (including configurationdata) to Receiving computers.
(c) < Partition >Copies a selected partition to Receiving computers.Refer to 16.2.2. Select Partition to send (refer to page38).
When you start sending, the Sending screen will be displayedwith the transmission progress and status. See screenshotbelow:
Use wyzx to move the cursor in the login table. Press +-to adjust Delay . Press p to break/abort all transmission.
Note: The Delay setting here is the same as the one in thesecond Sending screen (refer to 15.3. Sending on page34).
8/14/2019 JR PCI NTv8 User Manual
38/85
Juzt-Reboot System/Data Recovery Card
38
The type of data it is sending is displayed on the first row in thetable. For Parameter data , it will display < Send Parameter Data > . For Partition data , it will display < Send Partition > ,
partition type , partition name and partition size . Details of other information on screen are described below:
Size : The size of the current partition being sent.
Time : Amount of time elapsed during transmission.
Complete (1) : Amount of time estimated for transmission tocomplete.
Complete (2) : Transmission progress (in %)
When transmission is completed, the message Sendcompleted! Press any key to continue... will be displayed atthe bottom of the screen (at the hotkeys row). Press any key tocontinue and return to the Sending screen.
15.3.2 Select Partition to SendSelects a partition to send for Net-Clone . See the screenshotbelow:
Use wy cursor keys to select partition and press f to startsending. Press ^ to exit. 15.3.3 Send CommandSends command(s) to Receiving computers on the LAN. See
the screenshot below:
8/14/2019 JR PCI NTv8 User Manual
39/85
Juzt-Reboot System/Data Recovery Card
39
Use wy cursor keys to select command and press f to startsending. Press ^ to exit and return to the Sending screen.
For descriptions of each command, see below:(a) Collect ID for Wake Up On Lan
Records the network card ID of all receiving computers.This function is required by IP Allocate utility, and WakeUp On Lan remote control.
(b) Date/Time AdjustmentSynchronizes the time and date of all Receiving computers with the Sending computer.
(c) Keyboard LockLocks up the keyboards of all Receiving computers withthe Sending computer.
(d) IP AllocateAllows the user to allocate IP addresses for eachReceiving computer.
(e) All Computer RebootRestarts all Receiving computers including theSending computer itself.
(f) All Computer Power Off Power off all Receiving computers including theSending computer itself. For this command to work, allcomputers must use ATX power supply.
Note:After you have finished transmitting all partitions and parameter data, it is recommended to reboot or power off all computers.This is to implement the new settings and operating system(s).
15.4 Wake Up On LANEnables sending computer to wake up (power on) allReceiving computers connected on LAN.
To use this function, the receiving computers must use ATXpower supply, motherboard with WOL support and network cardwith WOL feature.
8/14/2019 JR PCI NTv8 User Manual
40/85
Juzt-Reboot System/Data Recovery Card
40
Note: Before executing this option, you have to executeCollect net card ID command (ie. Under the Sending screen,
select Sending l :Finish login m :Send command Collect ID for Wake Up On Lan ).
15.5 Net-Clone with Packet Driver The Net-Clone feature can be used with Network Adapters thatare not supported in the Packet Driver list as long as the PChas a Network Adapter installed, and has a DOS version of thepacket driver.
You will first have to obtain the packet driver for the NetworkAdapter, either in the network cards driver diskette or you can
download from the network cards manufacturers web site.To perform Net-Clone , follow the procedures shown below:
Step 1: Boot from floppy drive A:Insert a DOS or Windows 95/98 Boot disk into thefloppy drive, and boot from this diskette. The DOSprompt A> should appear.
Step 2: Run network card packet driver Insert network card driver disk into the floppy drive.
Look for the packet driver (usually under a folder called PKTDRV or a similar folder name) in thediskette. Once the packet driver file is located (e.g:RTSPKT.COM, E2000.COM, PKTDRV.COM,DLKPKT.COM, etc.), type the name of this file,followed by the interrupt number 0x60 and press f .See the example below:
A> RTSPKT 0x60 f
Step 3: Run Net-Clone utility
Insert Juzt-Reboot LAN-DRV Upgrade Disk into thefloppy drive. Change to the SNCOPY directory with thefollowing command:
A> CD \SNCOPY f
8/14/2019 JR PCI NTv8 User Manual
41/85
Juzt-Reboot System/Data Recovery Card
41
Look for the executable files named SC_TSR.COM and SC-xx.EXE (the xx represents the versionnumber) in the diskette. Type the name of these files
and press f to run the Net-Clone utility, as shown inthe examples below:
A> SC_TSR fA> SC-22 f
You may now proceed to 16. Using Net-Clone (onpage 31) on usage and functions.
Note: These procedures are rather technical and are not meantfor ordinary users who are not familiar with DOS mode and CLI
(command line interface).
8/14/2019 JR PCI NTv8 User Manual
42/85
Juzt-Reboot System/Data Recovery Card
42
16. FAQsFrequently Asked Questions:
16.1. General FAQs
1. Q. How does Intelligent Backup Technology work?A. Intelligent Backup Technology works by recording
changes made to the HDD, thus it only requires a small amount of HDD space to operate.
2. Q. Is it easy to install?A. Yes. It is Plug and Play.
3. Q. Can Juzt-Reboot be upgraded?A. Yes. You can download the upgrades at our website
(www.juzt-reboot.com).
4. Q. Can Juzt-Reboot coexist with integrated or software modems?
A. Yes. There are no known conflicts.
5. Q. Can Juzt-Reboot support Linux, Unix and BSDoperating systems?
A. Yes, under "Backup Restoration Mode".
6. Q. Is there going to be a Mac version of Juzt-Reboot?A. We are considering the possibility of a Mac version in
the future.
7. Q. Can I know where Juzt-Reboot has been used?A. Juzt-Reboot has been used in places like universities,
colleges, libraries, school computer labs, libraries; R & DCenters, educational labs, training centers, Internet stations, corporate sector, government sector, and
private enterprises, etc.
8. Q. Why those places?A. In these places, the computers are always being
accessed by many different people all the time. Juzt-Reboot will protect the computers operating systemagainst modifications, tampering, pranks and viruses.
8/14/2019 JR PCI NTv8 User Manual
43/85
Juzt-Reboot System/Data Recovery Card
43
9. Q. My computer already has an operating system. Do Ihave to reinstall to use Juzt-Reboot ?
A. No. Juzt-Reboot can retain your existing DOS or
Windows operating system. For other operating systems, please back them up and use Advanced toconfigure the partitions before installing or restoring frombackups.
10. Q. There are other software only solutions in themarket. What makes Juzt-Reboot special and whydoes it require a hardware card?
A. Software only solutions can easily be hacked and cannot offer any real protection outside the operating system. The Juzt-Reboot hardware card can protect against such intrusion or corruption by intercepting themoutside the operating system or at the hardware level.
11. Q. Why software only solutions cannot offer protection"outside the operating system"?
A. "Software only solutions" are specifically written for anoperating system. If the operating system is not running,then the "software only solution" cannot operate. Anexample is the BIOS/CMOS settings which come first before any operating system.
12. Q. Can Juzt-Reboot protect the BIOS/CMOS settings?A. Yes. It will automatically restore a good copy when any
of the settings are tampered with or become corrupted.
13. Q. Why should I protect the BIOS/CMOS settings?A. If the BIOS/CMOS settings are corrupted, your
computer may not start, hang or behave abnormally, or it may even crash your operating system or corrupt your HDD.
14. Q. Can you assure me that Juzt-Reboot's password issecure?
A. Yes. Juzt-Reboot emphasizes on security.
15. Q. What is "Supervisor mode" ?A. "Supervisor mode" is usually for the computer
administrator or manager. In this mode, whatever changes made (editing/deleting/moving/renaming files,installing/upgrading/removing software, etc.) will be
permanent.
8/14/2019 JR PCI NTv8 User Manual
44/85
Juzt-Reboot System/Data Recovery Card
44
16. Q. What is "User mode"?A. "User mode" is for computer users and public access. In
this mode, whatever changes made (editing/ deleting /
moving / renaming files, installing / upgrading / removing software, etc.) are temporary and when rebooted,everything returns back to the original setup.
17. Q. Can someone FORMAT/FDISK the HDD under User mode?
A. No. It is impossible even in real DOS mode. Even if someone tries, just reboot and everything will be back tonormal.
18. Q. How can I reformat my HDD without removing Juzt-
Reboot?A. You can reformat your HDD under Supervisor mode
only.
19. Q. How can I retrieve my Supervisor password if Iforget it?
A. If you forget your password, you can only retrieve anencrypted form of the password, since Juzt-Reboot stresses on security of the system. When you are
prompted for the Supervisor password, press down thej key and type in 2329 , and then press the F10 key.The screen will clear and a string of characters appears.Copy down the string exactly, and send it to your distributor/dealer or to us directly (at support@juzt-reboot.com) for decoding of the password. Please alsosend along proof of ownership of the card.
20. Q. My Juzt-Reboot card cannot be detected after accessing hardware settings by Ctrl+H. How tosolve this problem?
A. Please check whether it is an ASUS Motherboard. If yes, you have to change the Hardware Mode fromdefault mode A to B. To change the hardware mode of the cards, you will need the RSETPCI utility disk to boot from. For v8.3 and later cards, press Alt + M to changethe hardware mode.
Change the hardware mode only when the PC cannot detect the card or cannot install at all
8/14/2019 JR PCI NTv8 User Manual
45/85
Juzt-Reboot System/Data Recovery Card
45
21. Q. My system is used for graphics creation and is diskI/O intensive and I find that my Juzt-Reboot frequently runs into low buffer situations. How to
solve this problem?A. The Juzt-Reboot buffer keeps track of all disk I/O while
Windows is running. If the Juzt-Reboot frequently fillsup and you have another partition (drive D:), then you can move some of you settings to save to drive D:. You can change your Windows or applications to save datafiles to drive D: and thus reducing the number of filesJuzt-Reboot has to keep track of. You can also movethe Windows Swap/Paging file to D: drive.
If you installed theJuzt-Reboot
card with the default 500MB buffer, you can also try uninstalling the Juzt-Reboot card, and then reinstall it and specify a larger buffer.
16.2. Installation FAQs1. Q. Before installing Juzt-Reboot, are there any steps
to perform?A. Please run Windows Scandisk and Disk Defragmenter
to ensure there are no file and system errors and to de-fragment the files on the hard disk.
2. Q. Why do I have to run Scandisk before installingJuzt-Reboot?
A. Before any installation, the HDD must be checked for errors. This is to ensure that all the original information,which Juzt-Reboot will use for restoration, is valid.
3. Q. Why do I have to defragment the HDD beforeinstalling Juzt-Reboot?
A. This is because Juzt-Reboot requires a largecontiguous area of the hard disk to allocate the buffer.Defragmentation will also ensure that all the files are not fragmented, and helps the system perform better by not having to seek all over the hard disk when loading system files.
8/14/2019 JR PCI NTv8 User Manual
46/85
Juzt-Reboot System/Data Recovery Card
46
4. Q. How do I go into "real DOS mode"?A. Just create a "Startup Disk" with "Add/Remove
Programs" in "Control Panel", and then boot from this
disk. Another method is to keep pressing the [F8] key when Windows is starting and then select "Command Prompt Only" from the menu.
5. Q. Windows ME has no real DOS mode at all. So howto go into "real DOS mode"?
A. Just create a "Startup Disk" with "Add/RemovePrograms" in "Control Panel", and then boot from thisdisk. Another method is to keep pressing the [F8] key when Windows is starting and then select "Command
Prompt Only" from the menu.6. Q. Which PCI expansion slot should I use?
A. Any free expansion slot will do.
7. Q. The Juzt-Reboot screen does not appear. Whatshould I do?
A. In the BIOS/CMOS settings, disable virus protection and select NETWORK/LAN as the first boot device. Someother BIOS require that the Network Boot feature to beenabled. For some older BIOS, enable "Option ROM".
8. Q. What is the use of "Hardware Mode" in the"Hardware Setup"?
A. The "Hardware Mode" is to set the compatibility level for Juzt-Reboot card. This is because different computers use different components and hardwaredesigns such as the motherboard chipset and BIOS.
9. Q. Which "Hardware Mode" do you recommend?A. If Juzt-Reboot card works properly with the default
"Hardware Mode" (default mode is A), then there is noneed to change it. Otherwise, try the other modes. Weusually recommend using mode B with ASUS motherboards, and mode C for Intel 845 and newer chipsets as well as many of the MSI motherboards.
8/14/2019 JR PCI NTv8 User Manual
47/85
Juzt-Reboot System/Data Recovery Card
47
10. Q. How can we change the Hardware Mode?A. If you have the latest version of the Juzt-Reboot card,
you can use press the a + M keys once you see the Juzt-Reboot HARDWARE: vx.x message. If you havean older version of the card, you will have to obtain acopy of the RSETPCI utility disk. Boot up the PC using the RSETPCI utility disk as the boot or driver disk. Thelatest version of the utility displays the current HardwareMode before prompting you for the Hardware Mode tochange to.
11. Q. An exclamation mark (!) appears on "IDE controller"in Windows "Device Manager" after installing Juzt-
Reboot card. Why?A. You must run the file "Setup.exe" located in theinstallation disk under Supervisor mode. This will install Juzt-Reboot 's IDE driver and utilities.
12. Q. After installing Juzt-Reboot, the CD-ROM drivecannot be detected. What should I do?
A. Make sure the CDROM drive is not sharing the primary IDE with the HDD. It is recommended to connect theCDROM drive to the secondary IDE.
13. Q. Are there any Windows ME drivers?A. You can use the Windows 95/98 driver which is fully
compatible with Windows ME.
14. Q. I have downloaded your upgrade from your website.How to upgrade Juzt-Reboot?
A. Extract the upgrade files into a blank floppy disk. Restart the computer and go into Juzt-Reboot "Configuration" menu, choose "Upgrade".
15. Q. How do I protect the BIOS/CMOS settings with Juzt-Reboot?
A. Enable "Auto-Restore CMOS data" function. But beforeyou do this, execute "Analyze CMOS data". Note that this operation will reboot the system twice.
8/14/2019 JR PCI NTv8 User Manual
48/85
Juzt-Reboot System/Data Recovery Card
48
16. Q. I intend to install and use Linux with Juzt-Reboot.Is there any important information I should knowbefore I install?
A. Juzt-Reboot supports Linux under Backup RestorationMode. Linux can only be installed in the first partitionand you must create a Linux swap partition. During installation, you will have to select the "Manually
partition with Disk Druid" option and manually select the previously configured Linux and Linux/SW partitions asthe Linux Native partition (mount point "/" and "ext3")and the Linux Swap partitions. Select the "Use LILO asthe boot loader" and that the LILO (Linux Loader) must be installed in the "First Sector of Boot Partition" instead
of the "Master Boot Record" (MBR). Lastly, if the boot sector is over 8.4GB from the beginning of the hard disk,then the "Force LBA32" option must be enabled.
17. Q. Can I change the size of the partitions after Juzt-Reboot has been installed?
A. Once the partitions have been set up, they cannot bechanged. You will have to backup all your partitionsand/or data and uninstall the card. Then recreate the
partitions with the desired sizes and set up everything again, or restore from your backups.
16.3. Hard Disk Copy FAQs1. Q. What is parameter data? In the manual, it only
states Juzt-Reboot information.A. Parameter data is actually Juzt-Reboot s data such
as passwords, partition information and configurationsettings of the source HDD.
2. Q. Is it necessary for destination computer to haveexactly the same hardware specifications for HardDisk Copy to work?
A. No, but it is recommended that the destination computers should be the same. If Windows detectschanges or differences in hardware (motherboard chipset, BIOS, VGA, etc) on the destination computer,the hardware detection cycle will start again.
8/14/2019 JR PCI NTv8 User Manual
49/85
Juzt-Reboot System/Data Recovery Card
49
3. Q. What are the hardware components in the computer that can be different?
A. The amount of RAM, CDROM drive, floppy disk drive
and keyboard. Windows detects and registers themautomatically.
4. Q. What are the hardware components in the computer that cannot be different?
A. The destination HDD type and capacity should be thesame although the destination HDD capacity can behigher.
5. Q. Please explain about HDD type and capacity.A. HDD type here refers to the number of physical
cylinders, heads and sectors. From these parameters,the HDDs capacity can be determined.
6. Q. Can I perform Hard Disk Copy to a HDD from adifferent manufacturer but with the same capacity?
A. Yes, provided the HDD have the same number of cylinders, heads and sectors.
7. Q. Can I perform Hard Disk Copy to a HDD of higher capacity?
A. Yes, provided the HDD have the same number of headsand sectors.
8. Q. Does HDD speed also affect Hard Disk Copyperformance?
A. Yes, the faster HDD will take less time for Hard Disk Copy to complete. For example: 7200rpm HDDs will copy faster than normal 5400rpm HDDs.
9. Q. The source and destination computers hardwareare identical. Why, after Hard Disk Copy, Windowsstarts hardware detection?
A. Some differences in the BIOS/CMOS settings and/or theBIOS version can still activate this hardware detection.
8/14/2019 JR PCI NTv8 User Manual
50/85
Juzt-Reboot System/Data Recovery Card
50
16.4. Network FAQs1. Q. Can I use Juzt-Reboot PCI-NT version in a
computer that supports WOL?A. Yes. But you will not be able to use the WOL function on
the motherboard.
2. Q. Can I use Juzt-Reboot WOL version in a computer that does not support WOL?
A. Yes. But you will not be able to use the WOL function onthe card.
3. Q. Is it necessary for every computer on the network tohave exactly the same hardware specifications for Net-Clone to work?
A. No, but it is recommended that all the computers should be the same. If Windows detects changes or differencesin hardware (motherboard chipset, BIOS, VGA, etc) onthe receiving computer, the hardware detection cyclewill start again.
4. Q. Can I use Net-Clone with the normal Juzt-Reboot PCI version and a network card?
A. Yes. But you must get the DOS packet driver for thenetwork card to do this. Usually the packet driver islocated in the network card's driver disk.
5. Q. Does network speed affect Net-Clone'sperformance?
A. Yes, faster network speed will give better performance.We recommend at least 100Mbps.
6. Q. Does HDD speed also affect Net-Clone'sperformance?
A. No, if the network speed is 100Mbps network. The HDD
data transfer rates nowadays can exceed the transfer rate of a 100Mbps network connection. However using "gigabit" networking will increase Net-Clone's
performance.
7. Q. The sending and receiving computers' hardware areidentical. Why, after Net-Clone, Windows startshardware detection?
A. Some differences in the BIOS/CMOS settings and theBIOS version can still activate this hardware detection.
8/14/2019 JR PCI NTv8 User Manual
51/85
Juzt-Reboot System/Data Recovery Card
51
Juzt-Reboot
Users Manual
SUPPLEMENTAL
INFORMATION
for AdvancedUsers
This supplemental information section to theJuzt-Reboot Users Manual provides additional
information for advanced users. Please use with care.Juzt-Reboot takes no responsibility for any problemsthat may occur with the use of this information.
8/14/2019 JR PCI NTv8 User Manual
52/85
Juzt-Reboot System/Data Recovery Card
52
S. Supplemental InformationThis section provides additional information for theJuzt-Reboot users. It includes information on how to changethe Windows Swap/Paging file location, how to move theOutlook Express email data to another folder, as well as theLinux installation procedure.
S1 Changing Windows Swap FileLocation
All versions of Windows require a Swap (or Paging) file whilerunning. The location of this file is typically on the system drive(drive C:). For example, in Windows 98, the file is typicallynamed Win386.swp and resides in C:\WINDOWS.
While Windows is running, it constantly swaps code in and outof memory and into the swap file. Thus the contents of the swapfile is constantly changing.
In a Juzt-Reboot protected system, all changes to files aretracked by the buffer, and the constantly changing swap fileplaces additional load to the Juzt-Reboot buffer. The load to
the buffer can be reduced by moving it to a location not trackedby Juzt-Reboot such as to drive D:.
The following guide below will take the user through steps of changing the Swap File location to a second partition, the D:drive.
S1.1 Changing Swap File Location in Windows 98
From the Windows desktop, locate the My Computer icon. With
the icon selected, right-click on the icon, and then click onProperties . (The same effect can also be achieved by clickingon Start, Settings , Control Panel , and then double-clicking onSystem .)
Now click on the Performance tab. Then click on the VirtualMemory button. You should then see a dialog box similar to theone shown on the next page.
8/14/2019 JR PCI NTv8 User Manual
53/85
Juzt-Reboot System/Data Recovery Card
53
Now click on the Let me specify my own virtual memory settings .Then click on Hard disk: to bring a drop down list. Select driveD: from the list as shown in the example below.
Then click on the OK button. The following dialog box willappear:
8/14/2019 JR PCI NTv8 User Manual
54/85
Juzt-Reboot System/Data Recovery Card
54
Now click on Yes to confirm. You will then be prompted torestart the PC. After the restart, the Swap File will have beenmoved to drive D: .
S1.2 Changing Swap File Location in Windows XP
From the Windows desktop, locate the My Computer icon. Withthe icon selected, right-click on the icon, and then click onProperties . (The same effect can also be achieved by clickingon Start, Settings , Control Panel , and then double-clicking onSystem .)
Now click on the Advanced tab. Then click on the Settings
button for Performance. You should then see a dialog boxsimilar to the one shown below.
Click on the Advanced tab. You should then see a dialog boxthat looks like the one on the next page.
8/14/2019 JR PCI NTv8 User Manual
55/85
Juzt-Reboot System/Data Recovery Card
55
Now click on the Change button for the Virtual Memory settings.You will get the Virtual Memory settings screen shown below.
8/14/2019 JR PCI NTv8 User Manual
56/85
Juzt-Reboot System/Data Recovery Card
56
To move the swap or paging file to another drive (for exampledrive D:), first disable the paging file on drive C: by following thesteps below. Then, continue with setting up the swap file on
drive D: :a) Selecting drive C: in the Drive [Volume Label] list. In the
above example, you can see that it has been selected, anda swap file sized between 336 and 672 MB has been set.
b) Click on the No paging file option, and click on Set.c) Select drive D: in the Drive [Volume Label] list (in this
example, we will be changing the swap file location to driveD:). The No paging file option is initially selected.
d) Click on the System managed size option, and then click onthe Set button.
e) Click on the OK button.f) A dialog box warning you that the changes you have madewill require a restart before taking effect is displayed.
g) After clicking on OK to this prompt, and on the other OK
buttons to close the other screens, you will be prompted torestart the computer. Click on Yes to restart the computer,and after the restart, the swap or paging file should then bein drive D:
S2 Changing My Documents folder location
The location of the My Documents folder, by default after installation, is in Drive C: . Most applications will store your datafiles in this folder.
The location of this folder can be changed to an alternativelocation or drive.
8/14/2019 JR PCI NTv8 User Manual
57/85
Juzt-Reboot System/Data Recovery Card
57
S2.1 Changing folder location in Windows 98
For this customization, you will have to use the WindowsRegistry Editor. Please note that if changes are madeincorrectly to the system, you may corrupt your Windows.Always make a backup copy of your System and User registryfiles before making any changes. In Windows 98, the MyDocuments folder is found in the directory C:\My Documents. Inthe example below, we will be changing it to a directory on driveD: called D:\My Documents. Please ensure that the directory onD: drive is created before proceeding.
1) To run the Windows Registry Editor, click on Start,
Run, type in regedit at the Run dialog box, andclick on the OK button.2) Click on My Computer to select as shown in the screen
below. Scroll up if needed to select it.
3) Click on Edit, and then Find (or press shortcut keysCtrl+F ) to bring up the Find dialog box. Type in C:\MyDocuments at the Find what: box. Click on the Find Nextbutton to start the search.
4) For each instance that it finds the text C:\My Documents inthe Data column on the right pane, edit it (double-click onthe Name value) and at the Edit String dialog box, changethe C:\My Documents to D:\My Documents. Leave any other text there as it is. An example is shown on the next page.
8/14/2019 JR PCI NTv8 User Manual
58/85
Juzt-Reboot System/Data Recovery Card
58
5) After editing the text, click on OK, and then press thefunction key F3 to continue and search for the next one toedit.
6) When all occurrences of C:\My Documents have been
changed to D:\My Documents, you can exit the registryeditor. Restart Windows for changes to take place.7) Remember to use Ctrl+B to backup to Juzt-Reboot if not
in Supervisor mode.
S2.2 Changing folder location in Windows XP
In Windows XP, there may be several users defined in thesystem. The changes will have to be done for each user individually. That is, you will need to log in to each user profile,and carry out the steps shown below.
In this example, we will be moving the location of theMy Documents for user Mike to a folder on drive D: . Theoriginal location of the folder is in C:\Documents and Settings\Mike\My Documents and, in this example, wewill be creating a folder D:\Documents and Settings\
Mike\My Documents in drive D: and them move the folder location to the folder on drive D: . Ensure that the destinationfolder has been created before proceeding.
8/14/2019 JR PCI NTv8 User Manual
59/85
Juzt-Reboot System/Data Recovery Card
59
1) Start up Windows Explorer. Locate My Documents andright-click as shown in the screen below.
2) Click on Properties and you will see the My DocumentsProperties dialog box as shown below.
8/14/2019 JR PCI NTv8 User Manual
60/85
Juzt-Reboot System/Data Recovery Card
60
3) Click on the Move button and you will see the Select aDestination dialog box shown below.
4) Expand the My Computer folder and select the D:\Documents and Settings\Mike\My Documents folder on driveD: and then click on the OK button. Then click on the OKbutton of the My Documents Properties dialog box to applythe setting.
S3 Changing Outlook Express store locationIf the PC is used to store the emails of several users, then for each user, the steps described further below will have to beperformed for each of the users.
In this example, we have a user named Gary. When his emailwas initially set up, Outlook Express automatically created aEmail Storage Folder for him automatically. Usually, the folder will be named similar to the example shown below:
C:\WINDOWS\Application Data\Identities\{A806BEE2-8CF9-11D9-9B0F-EA31E5E9DA60}\Microsoft\OutlookExpress\
8/14/2019 JR PCI NTv8 User Manual
61/85
Juzt-Reboot System/Data Recovery Card
61
The objective is to move the Store Location to a folder on driveD: so that emails downloaded will be preserved and not lost onreboot of the Juzt-Reboot protected drive C: .
In this example, we will be changing the Store Location to adirectory on drive D: named as shown below:
D:\Data\Gary\Outlook Express\
1) Start up Outlook Express (of the selected user if there ismore than one profile).
2) Click on Tools, and then on Options. You should then seea screen similar to the one shown below.
8/14/2019 JR PCI NTv8 User Manual
62/85
Juzt-Reboot System/Data Recovery Card
62
3) Click on the Maintenance tab. You should see a screensimilar to the one shown below.
4) Click on the Store Folder button. You will then see a dialogbox similar to the shown below.
5) Click on the Change button. At the Browse for Folder dialog box, you can select the desired directory. In our example, we will be using the above-mentioned directory:D:\Data\Gary\Outlook Express\ . Please ensurethat the folder has been created first before you start tobrowse for the folder.
8/14/2019 JR PCI NTv8 User Manual
63/85
Juzt-Reboot System/Data Recovery Card
63
6) Once you have selected the folder and clicked on the OKbutton, you will see a dialog box similar to the one shownbelow.
7) Click on the OK button to complete the change. You willthen see the following message.
8) As described in the message, you will have to exit fromOutlook Express and restart it. On restart of OutlookExpress, it will automatically move all the email files for Gary to the specified directory.
S4 Multi-OS InstallationThe installation procedure for installing multiple OperatingSystems under Juzt-Reboot is described below.
To implement multiple Operating Systems under Juzt-Reboot,you MUST use the Advanced Installation mode.
Note:The use of the Advanced installation mode will wipe off ALLEXISTING DATA from your hard disk. If the data is important,please ensure that you have made a backup of your databefore attempting installation.
The Advanced installation mode will clear out all existing dataand prepare a blank disk ready to allocate the OS and datapartitions to be set up on the hard disk.
8/14/2019 JR PCI NTv8 User Manual
64/85
Juzt-Reboot System/Data Recovery Card
64
To illustrate the multi-boot feature, we will use an examplebelow, where the hard disk will be set up with three OperatingSystems, together with some data partitions.
No Attrib Name Size File System Restore Type Buffer1. [T] [Win 98 ][ 2000] [FAT32 ] [Every ] [ 502]2. [P] [Win 98 ][ 5000] [FAT32 ] [ ] [ ]3. [T] [Win XP ][ 10000] [NTFS ] [Every ] [ 502]4. [P] [Win XP ][ 20000] [FAT32 ] [ ] [ ]5. [B] [Linux ][ 15000] [Linux ] [ ] [ ]6. [P] [Linux ][ 1000] [Linux/SW] [ ] [ ]
In the above example, the Windows 98 and Windows XP OSpartitions are configured with the T attribute (Instant Restore
OS partition), while the Linux partition is configured with the Battribute (Backup Restore OS partition).
Note:Please note that when you set up an OS partition with the Battribute (Backup Restore OS partition), it will create a backuppartition of similar size automatically. The Free Space reportwill be reduced by an equivalent amount. This backup partitionwill not be visible in the partition list.
To perform the installation, first select the Advanced option atthe Install Setup screen.
It will perform the installation and reboot to the Multi-Bootscreen to configure the OS and data partitions. Enter thedesired OS and data partitions for your environment.
After saving the configuration and rebooting, you will bepresented with the Juzt-Reboot OS boot menu.
You now have three OS partitions and their data partitions, but
all of them are blank and unformatted.
To install the Operating Systems in each respective OSpartition, you will need the Install CD for the OS and ensure thatthe CD-ROM has been configured as a boot device before theHard Disk.
8/14/2019 JR PCI NTv8 User Manual
65/85
Juzt-Reboot System/Data Recovery Card
65
For the first OS, place the respective Installation CD in the CD-ROM drive, select the OS from the boot menu and press thee key to start the boot process. Since the CD-ROM is the
first boot device (after the Juzt-Reboot card), it will start theOS installation process. Each time the installation processreboots the PC, at the Juzt-Reboot OS boot menu, select thecorrect OS and boot to it to continue the installation process.
You will need to perform this step for each of the OperatingSystems you plan to install on the system.
In the example given above, you will have to repeat the processthree times. (For installation procedure for Linux OS, pleaserefer to the next Chapter).
S5 Red Hat Linux Installation Procedure
The installation procedure for installing other OperatingSystems such as Linux is described below.
Note:a) Other Operating Systems such as Linux and other versions
of Unix are supported in the Backup Recovery mode only.b) Operating Systems using Backup Recovery mode must be
set up in Advanced installation mode. This means that allexisting information in the hard disk is deleted beforeproceeding.
c) OS Partitions created using the B (Backup Restoration)attribute will automatically create another partition of similar size. This backup partition will not be displayed.
The example below illustrates the partitioning in the Multi-Bootscreen for a multi-boot environment consisting of a WindowsXP Operating System and data partition as well as a Red HatLinux operating system.
8/14/2019 JR PCI NTv8 User Manual
66/85
Juzt-Reboot System/Data Recovery Card
66
No.Attrib Name Size File System Restore Type Buffer1. [B] [Win XP ][ 6000] [NTFS ] [Every ] [ 502]2. [P] [Win XP ][ 10000] [FAT32 ] [ ] [ ]
3. [B] [RH Linux ][ 4000] [Linux ] [ ] [ ]4. [P] [RH Linux ][ 1200] [Linux/SW] [ ] [ ]
T =>Instant Restore Boot PartitionB =>Backup Restore Boot PartitionC =>No Restore Boot PartitionS =>Shared Data PartitionP =>Private Data Partition (Give the same name as boot partition)
After partitioning in the Multi-Boot screen, you can now start toinstall Linux. Ensure that the CD-ROM has been configured asa boot device ahead of the Hard Disk to allow booting from the
Red Hat Linux installation CD.
The steps shown below are for Red Hat Linux 8, but should besimilar for other versions of Red Hat as well as other distributions of Linux.
Step 1. In the Juzt-Reboot OS boot menu, select the correctpartition (in our example, it is RH Linux ). Place theRed Hat Linux CD into the CD-ROM drive. Presse to start installing Linux Operating System
8/14/2019 JR PCI NTv8 User Manual
67/85
Juzt-Reboot System/Data Recovery Card
67
Step 2. Press e when boot is displayed as shown on thescreen below.
Step 3. Select Skip when prompted to test the CD.
8/14/2019 JR PCI NTv8 User Manual
68/85
Juzt-Reboot System/Data Recovery Card
68
Step 4. Click on Next and select language asEnglish(English)
8/14/2019 JR PCI NTv8 User Manual
69/85
Juzt-Reboot System/Data Recovery Card
69
Step 5. Setup Keyboard as U.S. English
Step 6. Mouse Configuration. Select the appropriate mouse.
8/14/2019 JR PCI NTv8 User Manual
70/85
Juzt-Reboot System/Data Recovery Card
70
Step 7. Install Type. Select Custom & click on Next .
Step 8. Disk Partitioning Setup. Select Manually partition withDisk Druid .
8/14/2019 JR PCI NTv8 User Manual
71/85
Juzt-Reboot System/Data Recovery Card
71
Step 9. You will then get two warning messages. Ignore bothand click Yes when asking to format SWAP partition.
8/14/2019 JR PCI NTv8 User Manual
72/85
Juzt-Reboot System/Data Recovery Card
72
Step 10. Partitioning. Edit /dev /hda1 , select / for mount pointand format this partition as ext3 .Edit /dev/hda2 , format this partition as swap
Click Next and Continue . You will then get format
warnings message. Click format
.
8/14/2019 JR PCI NTv8 User Manual
73/85
Juzt-Reboot System/Data Recovery Card
73
8/14/2019 JR PCI NTv8 User Manual
74/85
Juzt-Reboot System/Data Recovery Card
74
8/14/2019 JR PCI NTv8 User Manual
75/85
Juzt-Reboot System/Data Recovery Card
75
8/14/2019 JR PCI NTv8 User Manual
76/85
Juzt-Reboot System/Data Recovery Card
76
Step11. Boot Loader Configuration. Change boot loader.Select Use LILO as the boot loader . Click on OK andenable the check box of Configure advanced boot loader options . Click Next to continue.
8/14/2019 JR PCI NTv8 User Manual
77/85
Juzt-Reboot System/Data Recovery Card
77
8/14/2019 JR PCI NTv8 User Manual
78/85
Juzt-Reboot System/Data Recovery Card
78
Step12. Configure advanced boot loader options. Install Bootrecord on: /dev /hda1 First sector of boot partition . If boot sector is over than 8.4GB, the check box of Force LBA32 must be enabled.
8/14/2019 JR PCI NTv8 User Manual
79/85
Juzt-Reboot System/Data Recovery Card
79
Step13. Network Configuration. Configure your networksettings.
Step14. Firewall Configuration. Setup your preferred Firewallsettings.
8/14/2019 JR PCI NTv8 User Manual
80/85
Juzt-Reboot System/Data Recovery Card
80
Step15. Additional Language Support. Setup your preferredsettings.
Step16. Time Zone Selection. Select your Location.
8/14/2019 JR PCI NTv8 User Manual
81/85
Juzt-Reboot System/Data Recovery Card
81
Step17. Account Configuration. Setup your Root password (6or more characters)
Step18. Authentication Configuration. Setup your preferredsettings.
8/14/2019 JR PCI NTv8 User Manual
82/85
Juzt-Reboot System/Data Recovery Card
82
8/14/2019 JR PCI NTv8 User Manual
83/85
8/14/2019 JR PCI NTv8 User Manual
84/85
Juzt-Reboot System/Data Recovery Card
84
Step21. Graphical Interface (X) Configuration. Select apreferred setting.
Step22. Customize Graphical Configuration. Select a preferredsetting.
8/14/2019 JR PCI NTv8 User Manual
85/85
Juzt-Reboot System/Data Recovery Card
Step23. Installation completed. select exit.
Recommended