View
216
Download
0
Category
Preview:
Citation preview
18 INCH SUBWOOFERSee NOTES TABULAR DATA for detailsCONFIGURATIONSubsystem: Transducer Loading
SUB 1x 18 in cone Vented
Operating Mode:
Amplifier Channels External Signal Processing
Single-amp LF DSP w/1-way filterPERFORMANCEOperating Range: 30 Hz to 150 Hz
Nominal Beamwidth: Horz 360° Vert 360°
Axial Sensitivity (SPL): LF(whole space) 94 dB 30 Hz to 150 Hz
(half space) 100 dB 30 Hz to 150 Hz
Input Impedance (ohms): Nominal Minimum
LF 8 7.1 @ 145 Hz
High Pass Filter: High Pass=>30 Hz, 12 dB/octave Butterworth
Accelerated Life Test:
System 80 V 800 W @ 8 ohm
Calculated Axial Output Limit (whole space SPL): Average Peak LF (whole space) 123 dB 129 dB
(half space) 129 dB 135 dB
ORDERING DATADescription Part Number
EAW JFL118 Black 2039875-90
Optional Accessories
Eye Bolt Forged Shoulder M10 X 1.5 X 37mm LG 0029818
Flybar JFL & HDA BLK [FB221] 2036411ACC CASTER KIT 100 [ACC-CK100] 0032377-90
FEATURES:• The JFL118 is the companion subwoofer to the JFL210 and JFL213. The JFL118’s simple-to-use rigging solution allows users to construct flown and ground stacked arrays with ease.
• The JFL118 is built to EAW construction standards with its rugged enclosure, sturdy finish and reinforced steel grille to stand up to life on the road.
• The JFL subwoofer offers an excellent choice for a wide range of portable and installed AV applications.
DESCRIPTION:The JFL118 is a light weight, high-powered, flyable, single 18-inch subwoofer that extends the low frequency response of the companion JFL210 or JFL213 full range line array loudspeakers. JFL118 subwoofers may be ground stacked, flown as part of a JFL210 or JFL213 array or flown separately alongside a JFL210 or JFL213 array. Integral, proprietary rigging will suspend up to six of any combination of JFL118 and JFL210/JFL213 enclosures with a 10:1 design factor. The optional FB121 fly bar includes multiple suspension points that allow users to easily set an array’s tilt angle. The JFL118 also includes M10 threaded suspension points that allow users to deploy arrays in permanently installed applications by means of cost-effective, forged shoulder eyebolts.
The JFL118 includes a metal cup that allows up to two JFL210 or JFL213 main channel loudspeakers to be pole mounted above up to two stacked JFL118’s. Alternately, JFL210 or JFL213 loudspeakers may be stacked directly atop the JFL118. In this instance, all enclosures lock together using their integral rigging.
JFL118 subwoofers utilize Neutrik® Speakon® STX Series connectors. The STX Series’ all-metal housings are extremely rugged, and feature a built-in gasket providing weather protection to IP54 when used with companion NLT4FX in-line cable connectors. The rear of each JFL118 features three NL4 connectors. Two are used for subwoofer and optional high passed signal input, while the third is used as an output to loop the high-passed signal to JFL210’s, JFL213’s or other loudspeakers.
Six year warranty.
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comNovember 2012Part Number: RD0744 Rev B00EAW products are continually improved. All specifications are therefore subject to change without notice.
JFL118 Specifications
NOTE: This drawing has been reduced. Do not scale.
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comNovember 2012Part Number: RD0744 Rev B00EAW products are continually improved. All specifications are therefore subject to change without notice.
JFL118 Specifications
PR
O E
NG
INE
ER
0030
530-
CD
-B_D
WG
_CU
ST_
JFL1
18
THE
INFO
RM
ATI
ON
CO
NTA
INE
DH
ER
EIN
IS P
RO
PR
IETA
RY
AN
DC
ON
FID
EN
TIA
L P
RO
PE
RTY
OF
LOU
D T
EC
HN
OLO
GIE
S, I
NC
.A
LL R
IGH
TS R
ES
ER
VE
DR
EV
ISIO
N:
DR
AW
ING
NU
MB
ER
:
THIR
D A
NG
LE P
RO
JEC
TIO
N
TITL
E:
SC
ALE
:1
1
ww
w.e
aw.c
omU
NLE
SS
OTH
ER
WIS
E S
PE
CIF
IED
:A
LL D
IME
NS
ION
S A
RE
IN M
ILLI
ME
TER
SD
UA
L [IN
CH
ES
] DIM
EN
SIO
NS
FO
R R
EF
ON
LY
TOLE
RA
NC
E IN
MIL
LIM
ETE
RS
LIN
EA
R ±
3.3
mm
/ ±
0.13
inA
NG
LES
± 1
°
(X.X
X) =
RE
F D
IMS
NO
TO
LER
AN
CE
IMP
LIE
D
TSC
= T
HE
OR
ETI
CA
L S
HA
RP
CO
RN
ER
DIM
EN
SIO
NS
AC
RO
SS
CE
NTE
RLI
NE
STO
BE
SY
MM
ETR
ICA
L
12
34
12
34
ABC
ABC
537.
0[2
1.14
]24
7.8
[9.7
6]
445.
4[1
7.53
]
396.
8[1
5.62
] 740.
2[2
9.14
]36
8.3
[14.
50]
631.
0[2
4.84
]
501.
7[1
9.75
]50
8.1
[20.
01]2X
247
.8[9
.76]
2X 1
78.6
[7.0
3]
2X 1
24.5
[4.9
0]
2X 1
24.5
[4.9
0]
2X 1
78.6
[7.0
3]
254.
0[1
0.00
]
94.0
[3.7
0]2X
86.
0[3
.39]
2X 1
75.0
[6.8
9]
2X 2
47.8
[9.7
6]
445.
4[1
7.53
]
216.
9[8
.54]
TS
C
2X 2
5.0°
537.
0[2
1.14
]
2X 4
85.0
[19.
09]
355.
6[1
4.00
]
DA
TEC
HA
NG
E N
UM
BE
RR
EV
11/4
/09
EC
OW
HT5
991
B
0030
530-
CD
B
AS
HE
ET
O
F 0.
050
DW
G C
US
TOM
ER
JFL
118
[ME
CH
AN
ICA
L S
PE
CIF
ICA
TIO
N]
TOP
FRO
NT
RIG
HT
SID
E
JFL1
18
DIM
EN
SIO
NS
AP
PLY
TO
BO
TH S
IDE
S
NO
TES
:1.
SY
MB
OL
I
ND
ICA
TES
MO
UN
TIN
G P
OIN
T,
M10
X 1
.5 T
HR
EA
DE
D H
OLE
(PI A
NG
LE).
2. S
YM
BO
L
IN
DIC
ATE
S C
EN
TER
OF
BA
LAN
CE
.3.
WE
IGH
T A
PP
RO
X. 4
4.5
kg [9
8.00
lb].
4. S
HIP
PIN
G W
EIG
HT
AP
PR
OX
. 51.
7 kg
[114
.00
lb].
TOP
HA
T4X
STA
CK
PA
D R
OU
TS
4X S
TAC
K P
AD
S
BO
TTO
M
2X H
AN
DLE
PR
OP
RIE
TAR
YR
IGG
ING
SY
STE
M
2X H
AN
DLE
PR
OP
RIE
TAR
YR
IGG
ING
SY
STE
M
OU
TPU
T
INP
UT
BA
CK
Exterior-grade Baltic birch plywoodWear resistant textured black paintPowder-coated perforated steel
MaterialFinishGrille
ENCLOSURE
PERFORMANCE DATASee NOTES GRAPHIC DATA for details
Frequency Response: ProcessedLF = green
Frequency Response: UnprocessedLF = green
SP
L (d
B)
SP
L (d
B)
Frequency (Hz) Frequency (Hz)
Processer ResponseLF = green
Ohm
s
dB re
0.7
75V
Frequency (Hz) Frequency (Hz)
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comNovember 2012Part Number: RD0744 Rev B00EAW products are continually improved. All specifications are therefore subject to change without notice.
JFL118 Specifications
ImpedanceLF = green
10 100 1000 20000
100
60
70
80
90
120
110
10 100 1000 20000
-10
-50
-40
-30
-20
10
0
10 100 1000 20000
0
-40
-30
-20
-10
20
10
100
10
110 100 1000 20000
NOTESTABULAR DATA 1. Measurement/Data Processing Systems: Primary - FChart: proprietary EAW software; Secondary - Brüel & Kjær 2012. 2. Microphone Systems: Earthworks M30; Brüel & Kjær 4133 3. Measurements: Dual channel FFT; length: 32 768 samples; sample rate: 48 kHz; logarithmic sine wave sweep. 4. Measurement System Qualification (includes all uncertainties): SPL: accuracy +/-0.2 dB @ 1 kHz, precision +/-0.5 dB 20 Hz to 20 kHz, resolution 0.05 dB; Frequency: accuracy +/-1 %, precision +/-0.1 Hz,resolutionthelargerof1.5Hzor1/48octave;Time:accuracy+/-10.4μs,precision+/-0.5μs,resolution10.4μs;Angular:accuracy+/-1°,precision+/-0.5°,resolution0.5°. 5. Environment: Measurements time-windowed and processed to eliminate room effects, approximating an anechoic environment. Data processed as anechoic or fractional space, as noted. 6. Measurement Distance: 7.46 m. Acoustic responses represent complex summation of the subsystems at 20 m. SPL is referenced to other distances using the Inverse Square Law. 7. Enclosure Orientation:Forbeamwidthandpolarspecifications,asshowninMechanicalSpecificationdrawing. 8. Volts: Measured rms value of the test signal. 9. Watts:Peraudioindustrypractice,“loudspeakerwatts”arecalculatedasvoltagesquareddividedbyratednominalimpedance.Thus,thesearenotTrueWattunitsofenergyasdefined by International Standard. 10. SPL: (Sound Pressure Level) Equivalent to the average level of a signal referenced to 0 dB SPL = 20 microPascals. 11. Subsystem: This lists the transducer(s) and their acoustic loading for each passband. Sub = Subwoofer, LF = Low Frequency, MF = Mid Frequency, HF = High Frequency. 12. Operating Mode:Userselectableconfigurations.Betweensystemelements,acomma(,)=separateamplifierchannels;aslash(/)=singleamplifierchannel.DSP=DigitalSignalProcessor. IMPORTANT:Toachievethespecifiedperformance,thelistedexternalsignalprocessingmustbeusedwithEAW-providedsettings. 13. Operating Range: Range where the processed Frequency Response stays within -10 dB SPL of the power averaged SPL within this range; measured on the geometric axis. Narrow band dips are excepted. 14. Nominal Beamwidth: Design angle for the -6 dB SPL points, referenced to 0 dB SPL as the highest level. 15. Axial Sensitivity: Power averaged SPL over the Operating Range with an input voltage that would produce 1 W at the nominal impedance; measured with no external processing on the geometric axis, referenced to 1 m. 16. Nominal Impedance: Selected 4, 8, or 16 ohm resistance such that the minimum impedance point is no more than 20% below this resistance over the Operating Range. 17. Accelerated Life Test:MaximumtestinputvoltageappliedwithanEIA-426Bdefinedspectrum;measuredwithrecommendedsignalprocessingandRecommendedProtectionFilter. 18. Calculated Axial Output Limit: Highest average and peak SPLs possible during the Accelerated Life Test. The Peak SPL represents the 2:1 (6 dB) crest factor of the Life Test signal. 19. High Pass Filter: This helps protect the loudspeaker from excessive input signal levels at frequencies below the Operating Range.
GRAPHIC DATA 1. Resolution:Toremoveinsignificantfinedetails,1/12octavecepstralsmoothingwasappliedtoacousticfrequencyresponsesand1/3octavecepstralsmoothingwasappliedtothebeamwidthand impedance data. Other graphs are plotted using raw data. 2. Frequency Responses: Variation in acoustic output level with frequency for a constant input signal. Processed: normalized to 0 dB SPL. Unprocessed inputs: 2 V (4 ohm nominal impedance), 2.83 V (8 ohm nominal impedance), or 4 V (16 ohm nominal impedance) referenced to a distance of 1 m. 3. Processor Response: The variation in output level with frequency for a constant input signal of 0.775 V = 0 dB reference. 4. Beamwidth:Averageangleforeach1/3octavefrequencybandwhere,startingfromtherearoftheloudspeaker,theoutputfirstreaches-6dBSPLreferencedto0dBSPLasthehighestlevel.Thismethod means the output may drop below -6 dB SPL within the beamwidth angle. 5. Impedance: Variation in impedance magnitude, in ohms, with frequency without regard to voltage/current phase. This means the impedance values may not be used to calculate True Watts (see 9 above). 6. Polar Data: Horizontal and vertical polar responses for each 1/3 octave frequency band 100 Hz to 16 kHz or Operating Range.
LEGENDHPF: High Pass Filter for crossover –or– Recommended High Pass Filter.LPF: Low Pass Filter for crossover.LF/MF/HF: Low Frequency / Mid Frequency / High Frequency.AMP: User Supplied Power Amplifier –or– Integral Amplifier for NT products.XVR: Passive LPFs, HPFs, and EQ integral to the loudspeaker.EAW Focusing: Digital Signal Processor capable of implementing EAW Focusing.
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comNovember 2012Part Number: RD0744 Rev B00EAW products are continually improved. All specifications are therefore subject to change without notice.
JFL118 Specifications
INPUT PANELS SIGNAL DIAGRAM
DSP EQHPFLPF
AMP
1-Way, Single-Amp (LF)
LF
REV: DESCRIPTION:
REVISIONS
A00 NEW ISSUE PER ECOWHT8990 MJC
DWG SPEC/INPUT JFL213
SCALE:
0030570-SDMJC 09/14/11DRAWING NUMBER:DATE:DRAWN BY:
1 of 1
80%REV:
A00LOUD TECHNOLOGIES INC, ALL RIGHTS RESERVED
ONE MAIN STREET, WHITINSVILLE, MA 01588 USA
LOUD Technologies Inc.
TITLE:
SHEET:ADOBE ILLUSTRATOR
NLT4MP
NLT4MP
NLT4MP
Recommended