Is Your Envelope “Effective”? of Effective Thermal Resistances for Exterior value Insulated...

Is Your Envelope “Effective”?

Mark Lawton P.Eng Morrison Hershfield Limited Vancouver

Designing an “Effective Envelope”

• Roofs • Below Grade Walls and

slabs • Glazing & Windows • Opaque portions of walls

2

Energy Consumption in Buildings

3

LEED and Energy

• As a prerequisite (EAp.1) you must: • Reduce design energy cost by 18% over the reference building built to

ASHRAE 90.1-1999 • An additional 10 points are available for exceeding the minimum. • Compliance shall be demonstrated using whole-building simulations

HOWEVER, THE RULE OF MODELING IS GARBAGE IN = GARBAGE OUTSO WHAT VALUES DO YOU PUT IN YOUR MODEL?

4

LEED and ASHRAE 90.1

5

• For steel-framed walls, ASHRAE 90.1 specifies amaximum effective conductivity of U-0.08 (R-13effective)

• To reduce effective U-value by 18% we require R-16effective

• In terms of nominal (rated) R-values, R-16 could be achieved using R-12 battinsulation + R-9 continuous insulation, or R-16 continuous insulation

Why Use Effective R-values?

• Nominal R-values are the rated insulation values provided by the manufacturer

• Effective R-values are the actual thermal resistances provided by the insulation in a given assembly

• Effective R-values can be much less than the nominal R-value of the insulation due to thermal bridging.

6

7

Opaque Wall Examples

• “Loss” in insulation value is due to thermal bridges: conductive elements which pass through the building thermal envelope

• Use of elements such as steel stud framing, z-girts, or exposed concrete slabs can result in major thermal bridging effects

8

Opaque Wall Examples

• Note continuous rigid insulation • Referred to as “continuous”

since no steel passes through Concrete Mass Wall Building type the insulation layer

• Not a lot of exposed concrete • Panel on left is window wall

9

Opaque Wall Examples

Steel Stud & Metal Panel Wall Cladding Girts Metal Panel Wall

• More than 50% opaque wall • Can be horizontal or vertical • Exterior insulation fits between

girts creating thermal bridging

10

Opaque Wall Examples

Masonry Veneer Over Steel Stud Masonry Veneer Wall Ties

• Minimal exposed structure • Thermal bridge at shelf angle • Minimum thermal bridge at ties

11

Thermal Bridging – 3D, 2D or 1D

12

Effects of Thermal Bridging Ef

fect

ive

Wal

l R-v

alu

18

16

14

12

10

8

6

4

2

0

5.5" cavity with insulation (R20 Batt) 3.5" cavity with insulation (R12 Batt) 5.5" uninsulated cavity 3.5" uninsulated cavity

0 5 10 15 20 25 30 35

Nominal R-Value of Exterior Insualtion

• Thermal bridging affects both the stud space and the exterior insulation

• R20 Batt in 5 ½” cavity gives and effective R14

• Maximum effective R value levels off around R16

13

Effects of Thermal Bridging

• MH conducted thermal modeling to establish effective U-values for standard wall assemblies

• Modeling indicated that traditional cladding attachment methods, such as z-girts, greatly reduce insulation performance

• Nominal R-values of insulation Vertical Z-girts are deceptive

14

Layered Girts

• A layer of insulation and horizontal z-girts topped by a layer of insulation and vertical z-girts

• Roughly 60% improvement over regular z-girts

Combined Horizontal and Vertical Z-girts

15

Thermally Broken Girts

• MH also modeled “alternative” cladding supports, designed to reduce thermal bridging and thus improve wall U-values

• Thermally broken z-girts

• Roughly 45% improvement over regular z-girts

Thermally Broken Vertical Z-girts

16

Intermittent Girts

• A layer of insulation and horizontal z-girts topped by a layer of insulation and vertical z-girts

• Percent improvement depends on how much of the girt is left

Intermittent Vertical Z-girts

17

Slab Edge Detailing

• MH also performed modeling to determine the impact of slab edge detailing on effective wall U-values

• Shelf angles or exposed concrete slabs provide a thermal bridge through the exterior plane of insulation

Shelf Angle and Brick Ties

18

Slab Edge Detailing

• Mounting shelf angle on brackets substantially reduces thermal bridging

• Other slab edge modeling included: • fully exposed slabs (i.e.

balconies, eyebrows) • insulation and z-girts outboard

of slab edge

Shelf Angle Mounted on Brackets

19

Effective R Value Tool

Program to compute the effective R-value of an elevation

20

Lookup Tables

• MH developed a tabular method of presentingresults

• Select the desired effective R-value, then look acrossthe table to see the necessary insulation thickness for common insulation types and cladding systems

• Tables allow easy comparison of different wallsystems when trying tomeet a required effective R-

Summary of Effective Thermal Resistances for Exterior value Insulated Walls (No Insulation in Frame Cavity, Slab

Effects Ignored)

21

22 2.62.60.00.00.0 4.23.80.40.40.5 5.44.80.70.81.0 7.56.31.41.72.0 97.32.12.53.0

10.38.22.83.44.0 11.59.13.54.25.0 12.6104.25.06.0 13.410.64.95.97.0Exterior

Insulation Placed

Outboard of Slab

2.62.62.60.00.00.0 3.83.83.40.40.40.5 4.84.74.20.70.81.0 6.46.465.11.41.72.0 7.87.675.72.12.53.0 98.57.96.32.83.44.0

10.29.48.76.93.54.25.0 11.210.39.47.44.25.06.0 12.111.19.97.84.95.97.0Exposed

Concrete Slab or Balcony

2″ x 1/16″ Brick Ties

Vert. & Hor. Girts

Hor. GirtsVert. GirtsSpray foamEXPSMineral Wool

Effective Wall R-ValueInsulation Thickness (Inches) Type ofThermal

Bridging atSlab

Type ofThermal

Bridging atSlab

Insulation Thickness (Inches) Effective Wall R-Value

Mineral Wool EXPS Spray foam 2″ x 1/16″ Brick Ties

Shelf Anglebolted to slab

Shelf Anglefastened to 3”x

¼” steel brackets spaced

at 24” o.c. 7.0 5.9 4.9 13.8 16.8 6.0 5.0 4.2 12.8 15.2 5.0 4.2 3.5 11.5 13.5

¼” Shelf Angle

4.0 3.4 2.8 10.1 11.6 3.0 2.5 2.1 8.7 9.7 2.0 1.7 1.4 7.1 7.7 1.0 0.8 0.7 5.1 5.3 0.5 0.4 0.4 4 4.1 0.0 0.0 0.0 2.6 2.6

23

The Payback

24

Thank You