View
244
Download
0
Category
Preview:
Citation preview
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 1/12
Chemical Engineering Science 64 (2009) 3498 -- 3509
Contents lists available at ScienceDirect
Chemical Engineering Science
journal homepage: w w w . e l s e v i e r . c o m / l o c a t e / c e s
Towards further internal heat integration in design of reactive distillation columns—
Part IV: Application to a high-purity ethylene glycol reactive distillation column
Fanghong Zhu, Kejin Huang ∗, Shaofeng Wang, Lan Shan, Qunxiong Zhu
College of Information Science and Technology, Beijing University of Chemical Technology, Beijing 100029, People's Republic of China
A R T I C L E I N F O A B S T R A C T
Article history:
Received 19 June 2008
Received in revised form 16 March 2009Accepted 23 April 2009
Available online 3 May 2009
Keywords:
Reactive distillation
Ethylene glycol
Internal heat integration
Process design
Process dynamics
Process operation
In the first three papers of this series, it has been shown that strengthening internal heat integration
within a reactive distillation column involving reactions with high thermal effect is really effective for the
reduction of utility consumption and capital investment besides the improvement in process dynamicsand operation. One important issue that remains unstudied so far is the influences of reaction selectivity
upon the reinforcement of internal heat integration, since the reaction operation is often accompanied by
side-reactions and the maintenance of a high selectivity is extremely necessary in process synthesis and
design. A reactive distillation column synthesizing high-purity ethylene glycol through the hydration of
ethylene oxide is chosen and studied in this work. Because of the unfavorable physicochemical properties
of the reacting mixture separated (e.g., the fairly large volatility between the reactants and the existence
of a consecutive side-reaction), the process represents a challenging problem for the reinforcement of in-
ternal heat integration. Intensive comparison is conducted between the process designs with and without
the consideration of further internal heat integration between the reaction operation and the separation
operation involved, and it has been found that seeking further internal heat integration still leads to a
substantial reduction of energy requirement, in addition to a further abatement in capital investment.
Moreover, a favorable effect is again observed upon the process dynamics and operability. These striking
outcomes manifest evidently that seeking further internal heat integration should be considered in pro-
cess synthesis and design irrespective of what a reaction selectivity has been assigned.
© 2009 Elsevier Ltd. All rights reserved.
1. Introduction
In the early papers of this series, the static and dynamic effect of
seeking further internal heat integration between the reaction oper-
ation and the separation operation involved was addressed in terms
of two hypothetical ideal reactive distillation columns involving, re-
spectively, a highly exothermic and a highly endothermic reactions
(A+B↔ C+D) and a reactive distillation column synthesizing methyl
tertiary butyl ether (MTBE) from isobutylene and methanol (Huanget al., 2005, 2006, 2008). In addition to a substantial enhancement
in thermodynamic efficiency and reduction of capital investment,
process dynamics and operability was found to be improved as well
when compared with the process designs without the consideration
of further internal heat integration. One important issue that re-
mains unstudied so far is the influences of reaction selectivity upon
the reinforcement of internal heat integration, since the reaction
operation is often accompanied by several side-reactions and the
∗ Corresponding author. Tel.: +86 10 64434801; fax: +8610 64437805.
E-mail address: huangkj@mail.buct.edu.cn (K. Huang).
0009-2509/$- see front matter © 2009 Elsevier Ltd. All rights reserved.
doi:10.1016/j.ces.2009.04.031
maintenance of a high selectivity is extremely necessary in process
synthesis and operation. Reaction selectivity is a key performance
index that evaluates the competition between the main- and side-
reactions in a process design. The stringent requirement on the re-
action selectivity might strongly affect process synthesis and design,
including certainly the configuration for internal heat integration. To
address this issue systematically, in this work we choose to study a
reactive distillation column synthesizing high-purity ethylene glycol
through the hydration of ethylene oxide. The process features irre-versible reactions with a large amount of thermal heat released (i.e.,
HR / HV ≈ 2.0 at the atmosphere pressure) and unfavorable physic-
ochemical properties (e.g., the fairly large relative volatility between
the reactants and the existence of a consecutive side-reaction). It
appears therefore to be a challenging system for examining the fea-
sibility and effectiveness of seeking further internal heat integration
upon process synthesis, design and operation.
There have already been many papers published on the synthe-
sis, design and operation of the ethylene glycol reactive distillation
columns. Okasinski and Doherty (1998) addressed the synthesis
and design of an ethylene glycol reactive distillation column and
presented useful insight into the process development. Several
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 2/12
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 3/12
3500 F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509
can facilitate internal heat integration between the reaction opera-
tion and the separation operation involved. It is worth mentioning
here that the distribution of catalyst is, in principle, valid for both
kinetically-controlled and equilibrium-limited reactions. However,
in the case of an equilibrium-limited reaction, if its reaction velocity
is so fast that chemical equilibrium can be reached instantaneously
on all reactive stages, then the distribution of catalyst presents no ef-
fect upon system performance, because the amount of catalyst influ-
ences both forward and backward reactions equally and gives no neteffect upon reaction equilibrium. In most cases, a sequential utiliza-
tion of these three methods (i.e., in a way similar to a single-variable
based searching method) could provide higher flexibility and more
advantages than each of them in consideration of further internal
heat integration between the reaction operation and the separation
operation involved and is therefore highly recommended during the
synthesis and design of reactive distillation columns involving reac-
tions with high thermal effect.
A unified notation, N r /N rea(n2) /N s(n1)∗, is employed to represent
different process designs with and without the consideration of fur-
ther internal heat integration throughout this work. N r , N rea, and N ssignify the number of stages in the rectifying, reactive and strip-
ping sections, respectively. The numbers in the parentheses, n1 and
n2, stand for the additional arrangement of reactive stages onto thestripping section and the movement of feed location of the domi-
nant feed in the reactive section. The asterisk, ∗, indicates a process
design finished after the redistribution of catalyst in the reactive sec-
tion. It is further stipulated that the dashed lines represent the static
and dynamic responses of the reactive distillation column developed
through the reinforcement of internal heat integration between the
reaction operation and the separation operation involved, and the
solid lines the static and dynamic responses of the process design
with the reactive section strictly between the rectifying section and
the stripping section (i.e., without the reinforcement of internal heat
integration). The black curves show the positive responses, and the
gray curves the negative responses.
3. Process description
Ethylene glycol (C2H6O2) is an industrially relevant product used
mainly as an anti-freezer in coolers, e.g., in motor vehicles. It is
usually produced from the reaction of ethylene oxide (C 2H4O) and
water (Eq. (1)). Ethylene oxide can react further with ethylene glycol
to produce the unwanted by-product diethylene glycol (C 4H10O3)
(Eq. (2)). Both reactions are highly exothermic and occur at moderate
temperatures, allowing production via a reactive distillation column.
In the case of a stoichiometric mole ratio between the two reactants,
a reactive distillation column can offer a higher selectivity than the
other types of reactors, e.g., a plug flow reactor (Corrigan and Miller,
1968; Stein et al., 1999). Owing to the sharp difference in relative
volatilities between the reactants: ethylene oxide and water, and
their near stoichiometric ratio in feed flow rates, the ethylene glycolreactive distillation column is often designated to operate in a total
refluxmode, andrectifying section is not necessary. Water is fed onto
the top of the reactive distillation column in order to facilitate the
suppression of the side-reaction, and the system can operate at the
atmosphere or even higher pressures. Although a higher operating
pressure favors the acceleration of the reaction velocity (Okasinski
and Doherty, 1998), additional expenditures are needed on fixed
investment and operating cost. The physiochemical properties of
the ethylene glycol reaction system can be found from Ciric and Gu
(1994) and Cardoso et al. (2000), and some of them are tabulated in
Table 1.
C2H4O(EO)+H2O(W ) → C2H6O2(EG)
HR =−80.0× 10
3
kJ / kmol
FH2O=26.3 kmol/h
2
10
14
FEO = 27.53 kmol/hVn = 668.99 kmol/h
B = 26.3 kmol/h
xEO = 0.0000
xW= 0.0026
xEG = 0.9480
xDEG = 0.0494
L1 = 721.88 kmol/h
Fig. 1. Design of the high-purity ethylene glycol reactive distillation column without
the consideration of further internal heat integration.
r (kmol m−3
s−1
)= 3.15× 1012
exp[−9547 /T ] xEO xH2O (1)
C2H4O(EO)+ C2H6O2(EG) → C4H10O3(DEG)
HR =−13.1× 103 kJ / kmol
r (kmol m−3 s−1)= 6.3× 1012 exp[−9547 /T ] xEO xEG (2)
For the simplification of simulation analysis, the following as-
sumptions have been made in this study:
(i) Vapor and liquid phases are in equilibrium on all stages.
(ii) Liquid phase is always homogeneous and no reaction occurs in
the vapor phase.
(iii) Sensible heat is negligible and the enthalpy of vaporization is
independent of composition and temperature.
(iv) No pressure drop is assumed across each stage.
In terms of the principle of mass and energy conservation in con-
junction with the given vapor–liquid equilibrium relationship, the
static and dynamic models of the high-purity ethylene glycol reac-
tive distillation column have been developed. Within the former, a
modified Newton–Raphson method is employed as the nonlinear
equation solver, and the satisfaction of component mass balance
equations on each stage as well as the attainment of the bottom
product specification is taken as the convergence criterion. Once
the composition of ethylene glycol in the bottom product has been
given, the heat duties of reboiler and condenser can be readily esti-
mated. Note that thespecification of thebottom composition of ethy-
lene glycol determines actually the reaction selectivity because the
bottom product is mainly composed of two components: ethyleneglycol and diethylene glycol (c.f., Fig. 1). By virtueof the latter, the dy-
namic behavior and controllability of the high-purity ethylene glycol
reactive distillation column can be evaluated with reference to the
given steady state operating condition in addition to the above static
calculation.
4. Process synthesis and design without the consideration of
further internal heat integration
Fig. 1 shows a basic process design of the high-purity ethylene
glycol reactive distillation column, 0/9/4. It has totally 13 stages be-
sides a total condenser (designated as stage 1 hereinafter) at the
top and a partial reboiler (designated as the last stage n hereinafter)
at the bottom. The reactive section is located above the stripping
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 4/12
F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509 3501
Table 1
Physical properties and nominal operating conditions of the high-purity ethylene
glycol reactive distillation column.
Parameters Values
System pressure (MPa) 0.101
Feeding stage of water 2
Feed flow rate of water (kmolh−1) 26.3
Feed flow rate of EO (kmol h−1) 27.53
The bottom product composition of EG
(mole fraction)
0.948
Latent heat (kJkmol−1) 40×103
The maximum limit of liquid holdup (m3) 0.1
Condenser holdup (kmol) 30
Reboiler holdup (kmol) 30
Reaction rate (kmol m−3 s−1)
Main-reaction 3.15×1012 exp[–9547/T ] xEO xW
Side-reaction 6.3×1012 exp[–9547/T ] xEO xEG
Heat of reaction (kJ kmol−1)
Main-reaction −80.0×103
Side-reaction −13.1×103
Vapor–liquid equilibrium constants at
the atmosphere pressure
EO 71.9 Exp[5.720(T −469)/(T −35.9)]
Water 221.2 Exp[6.310(T −467)/(T −52.9)]
EG 77.0 Exp[9.940(T −645)/(T −71.4)]DEG 47.0Exp[10.42(T −681)/(T –80.6)]
Table 2
Process designs with and without consideration of further internal heat integration
between the reaction operation and the separation operation involved.
Process design 0/9/4 0/9(2)/4(4)* 0/9(2)/6(4)
Number of stages (including
condenser and reboiler)
15 15 17
EO feed location 10 8 8
Distribution of catalyst (m3)
1 Condenser Condenser Condenser
2 0.1 0.043 0.043
3 0.1 0.043 0.043
4 0.1 0.043 0.043
5 0.1 0.043 0.043
6 0.1 0.043 0.043
7 0.1 0.043 0.043
8 0.1 0.043 0.043
9 0.1 0.1 0.1
10 0.1 0.1 0.1
11 0 0.1 0.1
12 0 0.1 0.1
13 0 0.1 0.1
14 0 0.1 0.1
15 Reboiler Reboiler 0
16 – – 0
17 – – Reboiler
section with the fresh ethylene oxide fed onto the bottom stage of
the reactive section. It is readily understood that no further inter-nal heat integration has been considered in this process design (i.e.,
no overlap between the reactive section and the stripping section
in view of the highly exothermic reactions involved). Tables 1 and 2
show the nominal operating conditions of the high-purity ethylene
glycol reactive distillation column. The liquid holdup is restrained to
be not greater than 0.1 m3 here so that excessive pressure drop can
be avoided on the reactive stages. Note that a fairly high reaction se-
lectivity (i.e., X EG /X DEG=19.19, where X EG is the molar concentration
of ethylene glycol and X DEG the molar concentration of diethylene
glycol in the bottom product) is assigned between the main- and
side-reactions in the nominal steady state.
The steady state profiles of temperature, vapor and liquid flow
rates, and liquid composition are shown in Fig. 2. Similar simulation
results were also presented by Ciric and Gu (1994), Baur et al. (1999),
Stage number
T [ K ]
0/9/4 0/9(2)/4(4)*
Stage number
L / V [ k m o l / h ]
L V
360
390
420
450
480
0
200
400
600
800
0
0.2
0.4
0.6
0.8
1
Stage number
X [ m o l e f r a c t i o n ]
EO water
EG DEG
1 3 5 7 9 11 13 15
1 3 5 7 9 11 13 15
1 3 5 7 9 11 13 15
Fig. 2. Steady state profiles: (a) temperature, (b) vapor and liquid flow rates, (c)
liquid composition (process designs: 0/9/4 and 0/9(2)/4(4)*).
Chen et al. (2000), Cardoso et al. (2000), Jackson and Grossmann
(2001) and Al-Arfaj and Luyben (2002).
5. Process synthesis and design with the consideration of
further internal heat integration
For the high-purity ethylene glycol reactive distillation column,
there exist two factors that make the reinforcement of internal heatintegration fairly difficult between the reaction operation and the
separation operation involved. One is the fairly large relative volatil-
ity between the reactants: ethylene oxide and water, which spans a
considerable range from 14.16 to 93.73 along the height of the re-
active distillation column. Ethylene oxide exists mainly in the vapor
phase and its liquid composition is extremely small throughout the
column, thereby limiting the effect of superimposing the reactive
section onto the stripping section. The other is the existence of a
consecutive side-reaction (i.e., Eq. (2)). As the reaction rate increases
more rapidly with temperature than that of the main-reaction (i.e.,
Eq. (1)), one can readily imagine that the allowance of these reac-
tions to occur simultaneously in the stripping section is likely to be
confined severely as long as the stringent reaction selectivity has to
be maintained.
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 5/12
3502 F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509
In order to show clearly the effect of seeking further internal heat
integration between the reaction operation and the separation oper-
ation involved, one has to guarantee that the total amount of catalyst
is maintained constant in all situations examined, although the ex-
act value should be subject to a detailed optimization search. Fig. 3
demonstrates the effect of the three methods outlined in Section 2
Reactive stages superimposed on the stripping section
H e a t d u t y [ M W ]
Ascending EO feed location
H e a t d u t y [ M W ]
7
7.3
7.6
7.9
8.2
7.2
7.5
7.8
8.1
6.4
6.8
7.2
7.6
8
Catalyst on the reactive stages superimposed
on the stripping section [m3]
H e a t d u t y [ M W ]
0 1 2 3 4
0 1 2 3 4 5
0.06 0.08 0.1 0.12 0.14
Fig. 3. Effect of seeking further internal heat integration on the high-purity ethylene
glycol reactive distillation column: (a) superimposition of reactive stages onto thestripping section, (b) relocation of EO feeding location, (c) redistribution of catalyst
among reactive stages.
Table 3
Effect of seeking further internal heat integration upon the high-purity ethylene glycol reactive distillation column.
Parameters Condenser/Reboiler duty [MW] Comparison (%)
Process design without further internal heat integration: 0/9/4 8.021/7.433 100/100
Seeking further internal heat integration
Superimposing four reactive stages onto the stripping section: 0/9/4(4) 7.616/7.029 94.951/94.565
Ascending EO feed location by two stages: 0/9(2)/4 7.955/7.367 99.177/99.112
Combinatorial use of the above methods: 0/9(2)/4(4) 7.611/7.024 94.888/94.498
Redistribution of catalyst: 0/9(2)/4(4)* 7.246/6.658 90.338/89.574
Final process design: 0/9(2)/6(4) 7.246/6.658 90.338/89.574
for the reinforcement of internal heat integration in the process de-
sign, 0/9/4. It is readily seen that all the three methods can be effec-
tive in improving the thermodynamic efficiency of the high-purity
ethylene glycol reactive distillation column. With the superimposi-
tion of the reactive section onto the stripping section, the heat duties
of condenser and reboiler decrease monotonically, and it appears
reasonable to allow the reactions to occur on all the stages in the
stripping section (c.f., Fig. 3a). Similar arrangements of the reactive
section were also reported by a number of researchers in terms of a MINLP optimization formulation (Papalexandri and Pistikopoulos,
1996; Cardoso et al., 2000; Jackson and Grossmann, 2001). These
realities imply that the fairly high reaction selectivity poses hardly
limitation on the reinforcement of internal heat integration between
the reaction operation and the separation operation involved. As far
as the feeding location of fresh ethylene oxide is concerned, the min-
imal energy requirement is reached when it has been fixed at stage
8 (c.f., Fig. 3b). Away from this stage will lead to the degradation in
the thermodynamic efficiency. The distribution of catalyst displays
a strong effect upon the thermodynamic efficiency, and more cata-
lyst should be employed in the common section where the reactive
section has been superimposed onto the stripping section (c.f.,
Fig. 3c). Here, for the simplification of computational analysis, the
catalyst distribution is assumed uniform above and below the EOfeed location, respectively, i.e., a two dimensional search is con-
ducted in this work. Although the optimal distribution of catalyst is
found to be 0.12 m3 per stage blow the EO feed location, the feasible
solution becomes 0.1 m3 per stage owing to the constraint that the
maximally permissible amount of catalyst should not exceed 0.1 m3
per stage. In Table 3, the detailed effect of seeking further internal
heat integration between the reaction operation and the separation
operation involved is summarized in terms of a close comparison
with the basic process design, 0/9/4. The replacement of all sepa-
rating stages with reactive ones in the stripping section (i.e., in the
process design, 0/9/4(4)) leads to a reduction of heat duty by 5.049%
in the condenser and 5.435% in the reboiler. Feeding ethylene oxide
onto stage 8 instead of 10 (i.e., in theprocess design, 0/9(2)/4) secures
a reduction of heat duty by 0.823% in the condenser and 0.888% inthe reboiler. Combinatorial application of these two methods results
in a better process design: 0/9(2)/4(4), than those by either of the
methods, with a reduction of heat duty by 5.112% in the condenser
and 5.502% in the reboiler. Redistribution of catalyst in the process
design, 0/9(2)/4(4)*, abates further energy requirement, giving rise
to a reduction of heat duty by 9.662% in the condenser and 10.426%
in the reboiler. The substantial improvement in the thermodynamic
efficiency signifies definitely the paramount importance of consider-
ing further internal heat integration between the reaction operation
and the separation operation involved in the high-purity ethylene
glycol reactive distillation column. In Fig. 2, the steady state profiles
of temperature, vapor and liquid flow rates, and liquid composition
are also illustrated for the resultant process design, 0/9(2)/4(4)*.
In comparison with the basic process design, 0/9/4, there appear
almost no substantial changes in the temperature and liquid com-
position profiles, and only have the liquid and vapor flow rates been
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 6/12
F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509 3503
FH2O= 26.3 kmol/h
2
8
16
FEO= 27.53 kmol/h
L1 = 652.15 kmol/h
14 Vn = 599.62 kmol/h
B = 26.3 kmol/hxEO = 0.0000
xW= 0.0026
xEG = 0.9480
xDEG = 0.0494
Fig. 4. Design of the high-purity ethylene glycol reactive distillation column with
the consideration of further internal heat integration.
reduced, implying a simultaneous abatement in capital investmentand operating cost.
Remember the fact that seeking further internal heat integration
in a reactive and non-reactive distillation column reduces actually
the driving forces of mass transfer in the rectifying/stripping section
where internal/external heat integration has been arranged (Melles
et al., 2000; Nakaiwa et al., 2003; Huang et al., 2006), it is there-
fore necessary to make an appropriate compensation to the mass
transfer driving forces during the synthesis and design of the high-
purity ethylene glycol reactive distillation column. A straightforward
method is to add a number of separating stages to the stripping sec-
tion, and this should be determined in terms of a detailed simulation
analysis. In this situation, two separating stages have been found to
be enough for the stripping section, leading to a final process de-
sign: 0/9(2)/6(4). The final process configuration of the high-purityethylene glycol reactive distillation column is depicted in Fig. 4, and
its nominal steady state operating conditions are also tabulated in
Table 2. In Fig. 5, the profiles of temperature, liquid and vapor flow
rates and liquid composition are illustrated for the process design,
0/9(2)/6(4). In comparison with the basic process design, 0/9/4, the
reboiler heat duty has been reduced by 10.426%, in addition to a
9.662% abatement in the condenser heat duty (c.f., Table 3). The ex-
tremely small improvement in the thermodynamic efficiency from
the process designs, 0/9(2)/4(4)* to 0/9(2)/6(4), implies, however, the
dominant effect of the combination between the reaction operation
and the separation operation involved upon the synthesis and design
of the high-purity ethylene glycol reactive distillation column.
6. Open-loop process dynamics
Fig. 6 shows the open-loop transient responses of the high-purity
ethylene glycol reactive distillation columns with and without fur-
ther internal heat integration between thereactionoperation andthe
separation operation involved when they are subject to a ± 33.45
kmol/h step change in the bottom vapor flow rate, respectively. As
can be seen, the high-purity ethylene glycol reactive distillation col-
umn is characterized by severe non-minimum phase behavior (i.e.,
initial inverse responses) and an under-damped response. In terms
of the close comparison between the process designs: 0/9/4 and
0/9(2)/6(4), one can readily understand that seeking further internal
heat integration helps to suppress the severity of the non-minimum
phase behavior although its effect appears to be quite marginal. The
process design, 0/9(2)/6(4), exhibits a smaller time constant than
Stage number
T [ K ]
Stage number
L / V [ k m o l / h ]
L V
360
390
420
450
480
0
200
400
600
800
0
0.2
0.4
0.6
0.8
1
Stage number
X [ m o l e f r a c t i o n ]
EO WaterEG DEG
1 5 9 13 17
1 5 9 13 17
1 5 9 13 17
Fig. 5. Steady state profiles: (a) temperature, (b) vapor and liquid flow rates, (c)
liquid composition (process design: 0/9(2)/6(4)).
0.75
0.85
0.95
Time [h]
X
E G
[ m o l e f r a c t i o n ]
–33.45
+33.45
0 5 10 15 20
Fig. 6. Open-loop transient responses of the high-purity ethylene glycol reactive
distillation columns with and without further internal heat integration when they are
subject to a ± 33.45 kmol/h step change in the bottom vapor flow rate, respectively.
Grey curves: negative responses; black curves: positive responses.
the process design, 0/9/4, despite the fact that a relatively larger de-
gree of under-dampness is observed in the former than in the latter.
These facts imply that the reinforcement of internal heat integration
gives no adverse effect to process dynamics.
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 7/12
3504 F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509
0.92
0.93
0.94
0.95
0.96
Time [h]
X
E G
[ m o l e f r a c t i o n ]
+2%
–2%
0 10 20 30 40
Fig. 7. Open-loop transient responses of the high-purity ethylene glycol reactive
distillation columns with and without further internal heat integration when they are
in the face of a ± 2% step change in the feed flow rate of fresh water, respectively.
Grey curves: negative responses; black curves: positive responses.
The occurrence of the non-minimum phase behavior is closely
related to the variation of water composition in the reactive section.
The increase/decrease of the heat duty of reboiler reduces/enhances
immediately the water composition in the reactive section and thus
theconversion rate of ethylene glycol. This is whythe bottom compo-
sition of ethylene glycol always exhibits an initial inverse response.
With the accumulation/depletion of water in the top condenser, the
level controller gradually increases/decreases the reflux flow rate
and thus the water composition in the reactive section, leading to
relatively slow variations in the conversion rate of ethylene glycol.
The variation caused by the reflux flow rate lasts for a relatively
long time and becomes the dominant one soon after the changes in
the bottom vapor flow rate. The interaction of these two conflicting
factors is, in fact, the principal reason for the occurrence of the non-
minimum phase behavior, and Eq. (3) shows the detailed mechanism
by assuming a first-order lag and an integrating process for the initial
inverse response and the one by the reflux flow rate, respectively.
K LT LS
− K V T V S+ 1
= (K LT V − K V T L)S+ K LT LS(T V S+ 1)
(3.1)
K LT V − K V T L<0 (3.2)
where T L T V and K L ≈ K V (because of the extremely small steady
state gain between the bottom composition of ethylene glycol and
the reboiler heat duty).
With the reinforcement of internal heat integration between
the reaction operation and the separation operation involved, the
dynamics associated with reflux flow rate is enhanced in rapidity
because of the reduction in the internal overflows, thus reducing
somehow the severity of the non-minimum phase behavior.
In Fig. 7, the open-loop transient responses of the high-purity
ethylene glycol reactive distillation columns with and without fur-
ther internal heat integration between the reaction operation andthe separation operation involved are depicted when they are in
the face of a ± 2% step change in the feed flow rate of fresh water,
respectively. In the circumstance of positive responses, fairly small
difference could be found between the process designs: 0/9/4 and
0/9(2)/6(4). In the case of negative responses, however, great dif-
ference could be observed between them. The process design with
further internal heat integration, 0/9(2)/6(4), could operate near the
desired steady state for a much longer time than the process design
without further internal heat integration, 0/9/4. This phenomenon
indicates that the former is less sensitive than the latter in the face
of disturbances from the feed flow rate of fresh water. The difference
in open-loop transient behaviors has been aroused by the different
characteristics of the interaction between the reaction operation and
the separation operation involved. After a certain period of time has
0.925
0.935
0.945
0.955
Time [h]
X
E G [ m o l e f r a c t i o n ]
–2%
+2%
0 10 20 30 40
Fig. 8. Open-loop transient responses of the high-purity ethylene glycol reactive
distillation columns with and without further internal heat integration when they
are subject to a ± 2% step change in the feed flow rate of fresh ethylene oxide,
respectively. Grey curves: negative responses; black curves: positive responses.
elapsed, the two process designs will finally reach the same steady
state, though it is not indicated in the figure.
Fig. 8 illustrates the open-loop transient responses of the high-
purity ethylene glycol reactive distillation columns with and withoutfurther internal heat integration between the reaction operation and
the separation operation involved when they are subject to a ± 2%
step change in the feed flow rate of fresh ethylene oxide, respec-
tively. For the dynamic responses to the negative change in the feed
flow rate of fresh ethylene oxide, difference can hardly be noticed
between the process designs: 0/9/4 and 0/9(2)/6(4). For the dynamic
responses to the positive change in the feed flow rate of fresh ethy-
lene oxide, however, sharp difference has been found between them.
The process design, 0/9(2)/6(4), can again operate around the desired
steady state for a longer time than the process design, 0/9/4, imply-
ing a certain degree of improvement in process dynamics aroused by
the reinforcement of internal heat integration between the reaction
operation and the separation operation involved. After a certain pe-
riod of time has elapsed, the two process designs will finally reachthe same steady state, though it is not indicated here.
7. Operability evaluation
The decentralized control schemes are depicted in Fig. 9. As can
be seen, the levels of condenser and reboiler are controlled, respec-
tively, with the reflux flow rate and bottom product flow rate, and
two proportional-only (P) controllers are adopted, here. The bottom
composition of ethylene glycol is controlled with the reboiler heat
duty, and a PI controller is employed. The water composition on the
sensitive stage is controlled with the feed flow rate of fresh water,
keeping the stoichiometric balance between the reactants, and a P
controller is used. While the sensitive stage locates on stage 15 for
the process design with further internal heat integration, 0/9(2)/6(4),it is on stage 13 for the process design without further internal heat
integration, 0/9/4 (c.f., Figs. 2 and 5). The flow rate of ethylene ox-
ide is designated as the production rate handle, and a first-order
lag with a time constant of 5.0 min is assumed in all concentration
measurements.
The decentralized control systems have been tuned with the fol-
lowing procedure. They are considered to be optimal for the respec-
tive process designs. For the water composition loops, the first-order
plus a time-delay transfer function models are developed based on
the step responses obtained through the perturbation of fresh wa-
ter flow rate. According to the Ziegler–Nichols rule, the proportional
gain can then be estimated as
K c = T W / (K W × dW ) (4)
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 8/12
F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509 3505
FC
LC
H2O
LCB, xEGCC
PC
EO
2
14
10
CC 13
FC
LC
H2O
LCB, xEGCC
PC
EO
CC
2
16
8
14
Fig. 9. Control schemes of the high-purity ethylene glycol reactive distillation
columns: (a) 0/9/4, (b) 0/9(2)/6(4).
where T W , K W , and dW are the time constant, process gain, and time-
delay of the developed transfer function models, respectively.
The bottom composition controllers are tuned in terms of an
experimental design approach. The ultimate gain and the ultimate
frequency are found by increasing the gain of a P controller until sus-
tained oscillations occur. Then, the Ziegler–Nichols settings are cal-
culated for the control loops. Finally, a detuning factor f is searched
for that makes all composition control loops have appropriate damp-
ing coefficients
K c = K ZN /f (5.1)
T I = T ZN × f (5.2)
where K c and T I represent the proportional gain and integral time,
respectively, and K ZN and T ZN denote the Ziegler–Nichols settings.
All the controller parameters are listed in Table 4. Notice that
while the P controller for the reboiler level is set to be 0.28, the
one for the condenser level is chosen to be 4.5. The tight inventory
control of the top condenser can facilitate the suppression of the
non-minimum behavior of the high-purity ethylene glycol reactive
distillation column (Huang et al., 2009).
The regulatory responses of the high-purity ethylene glycol re-
active distillation columns with and without further internal heat
integration between the reaction operation and the separation op-
eration involved are presented in Fig. 10 when they have been
upset by a ± 2% step change in the feed flow rate of fresh ethy-
Table 4
Controller parameters for the high-purity ethylene glycol reactive distillation column.
Distilation
column
Control loops
Condenser level
control loop
Reboiler level
control loop
Bottom EG
control loop
Stoichiometric balance
control loop
0/9/4
K C 4.5 0.28 8.0 12.35
T I 0 0 0.03 0
0/9(2)/6(4)K C 4.5 0.28 8.0 15.91
T I 0 0 0.03 0
lene oxide, respectively. As can be seen, the process design with
further internal heat integration, 0/9(2)/6(4), compares favorably
with the process design without further internal process integra-
tion, 0/9/4, displaying not only smaller maximum deviations, but
also shorter settling times. At the new steady states reached, the
former maintains its higher thermodynamic efficiency than the
latter.
Fig. 11 displays the regulatory responses of the high-purity ethy-
lene glycol reactive distillation columns with and without further
internal heat integration between the reaction operation and theseparation operation involved when the reactant of ethylene oxide is
changed from a pure component flow of ethylene oxide (i.e., Z EO=1.0
and Z W = 0.0) into a mixture flow of ethylene oxide and water (i.e.,
Z EO=0.9 and Z W = 0.1). In this case, oscillatory responses are exhib-
ited in both the process designs. With the consideration of further
internal heat integration in the process design, 0/9(2)/6(4), the de-
gree of oscillation has been suppressed considerably, resulting in a
substantial reduction in settling time.
In Fig. 12, the servo responses of the high-purity ethylene gly-
col reactive distillation columns with and without further internal
heat integration between the reaction operation and the separation
operation involved are illustrated when they have been upset by a
± 0.01 step change in the set-point of bottom control loop, respec-
tively. Again, it can be seen that the process design, 0/9(2)/6(4), out-performs, 0/9/4, with a reduced degree of oscillations. Much long
settling times are needed to reach the desired steady state in both
the process designs, and it is due to the improper selection of oper-
ating region (i.e., too high a conversion rate for ethylene glycol leads
to an extremely small process gains between the bottom composi-
tion of ethylene glycol and the reboiler heat duty). In such an oper-
ating region with a bottom composition of ethylene glycol as high as
94.8 mol%, severe non-linearity and non-minimum phase behavior
occurs, degrading further the process operability. These simulation
outcomes are in excellent agreement with our insights gained from
the studies of open-loop process dynamics.
8. Discussions
Owing to the combination of reaction operation and separation
operation within one framework, the synthesis and design of re-
active distillation columns become much more complicated than
those of conventional distillation columns. In spite of the fact that
seeking further internal heat integration is actually a single-variable
based searching method, it can effectively deal with the multi-
variable nature of the synthesis and design of reactive distillation
columns involving reactions with high thermal effect. In compar-
ison with the currently available methods for process synthesis
and design, e.g., the MINLP formulation, it appears extremely sim-
ple in principle, fairly easy to adopt in applications, and requires
no complicated mathematical vehicles. Even for the high-purity
ethylene glycol reactive distillation column that contains reactions
with extremely unfavorable physicochemical properties (e.g., the
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 9/12
3506 F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509
Time [h]
X E G [ m o l e f r a c t i o n ]
Time [h]
V n
[ k m o l / h ]
0.93
0.94
0.95
0.96
0.3
0.35
0.4
0.45
0.5
Time [h]
X W [ m o l e f r a c t i o n ]
560
590
620
650
680
710
25.6
26
26.4
26.8
27.2
Time [h]
F W [
k m o l / h ]
620
660
700
740
Time [h]
R R [ k m o l / h ]
+2%
–2%
+2%
–2%
+2%
–2%
+2%
+2%
–2%
–2%
–2%
+2%
–2%
–2%
0 4 8 12 16 20
0 4 8 12 16 20 0 4 8 12 16 20
0 4 8 12 16 20
0 4 8 12 16 20
Fig. 10. Regulatory responses of the high-purity ethylene glycol reactive distillation columns with and without further internal heat integration when they have been upset
by a ± 2% step change in the feed flow rate of fresh ethylene oxide, respectively: (a) composition of ethylene glycol in the bottom product, (b) bottom vapor flow rate, (c)
composition of water on the sensitive stage, (d) feed flow rate of fresh water, (e) reflux flow rate. Grey curves: negative responses; black curves: positive responses.
fairly large relative volatility between ethylene oxide and water)
and the existence of a consecutive side-reaction, it can give rise to
a satisfactory process design with not only higher thermodynamic
efficiency and lower capital investment but also further improved
dynamics and operability than the conventional design practice,
reflecting its inherent reliability and robustness. These striking
results imply that the presence of high reaction selectivity does
not confine very much the reinforcement of internal heat integra-
tion between the reaction operation and the separation operation
involved.
It is worth investigating the intricate mechanism that seeking fur-
ther internal heat integration could improve process dynamics andoperability for the high-purity ethylene glycol reactive distillation
column. Generally speaking, the way to integrate the reaction opera-
tion and the separation operation involved is one of the primary fac-
tors that determine the dynamics and operability of a reactive distil-
lation column. Unfortunately, very few systematic methods are now
available for process synthesis and design based on dynamic perfor-
mance indexes. Seeking further internal heat integration searches
for the optimum process design in terms of an economic objec-
tive (i.e., thermodynamic efficiency). Too strong/weak internal heat
integration can certainly not yield a process design with high ther-
modynamic efficiency because of the interactions between the re-
action operation and the separation operation involved. The same is
also true for the resultant process dynamics and operability. There-
fore, seeking further internal heat integration works essentially to
enhance the thermodynamic efficiency through compromising the
reaction operation and the separation operation involved (Huang
et al., 2007). This is the major reason why process dynamics and op-
erability can be improved simultaneously along with the enhance-
ment of the thermodynamic efficiency for the high-purity ethylene
glycol reactive distillation column.
It is imperative to gain further insight into the fact that the
presence of a high reaction selectivity does not confine very much
the reinforcement of internal heat integration between the reaction
operation and the separation operation involved. Although the con-
clusion has been derived from the specific case study of the high-
purity ethylene glycol reactive distillation column, it is consideredto be of general significance, irrespective of what kinds of reaction
kinetics (e.g., exothermic or endothermic, series, parallel, or even
combined, etc.) involved in the reactive distillation columns. It is
certainly impossible to prove this corollary theoretically due to the
existence of innumerable reaction systems and their corresponding
process designs, the inherent characteristics of internal heat inte-
gration may, however, allow us giving the above deduction. As has
already been demonstrated in the previous and the current papers,
the reinforcement of internal heat integration helps to balance the
interaction between the reaction operation and the separation oper-
ation involved. It is the resultant coordinated relationship that pro-
vides additional flexibility for keeping the process innovation from
the violation of the reaction selectivity given in the basic process
design.
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 10/12
F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509 3507
Time [h] Time [h]
0.84
0.88
0.92
0.96
1
0.3
0.5
0.7
0.9
Time [h]
X E G [ m o l e f r a c t i o n ]
X W [ m
o l e f r a c t i o n ]
550
600
650
700
750
800
20
22
24
26
28
Time [h]
V n
[ k m o l / h ]
F W [ k
m o l / h ]
600
650
700
750
800
Time [h]
R R [ k m o l / h ]
0 10 20 30 40
0 10 20 30 40 0 10 20 30 40
0 10 20 30 40
0 10 20 30 40
Fig. 11. Regulatory responses of the high-purity ethylene glycol reactive distillation columns with and without further internal heat integration when the fresh reactant of
ethylene oxide is changed from a pure component flow ( Z EO = 1.0 and Z W = 0.0) into a mixture flow of reactants ethylene oxide and water ( Z EO = 0.9 and Z W = 0.1): (a)
composition of ethylene glycol in the bottom product, (b) bottom vapor flow rate, (c) composition of water on the sensitive stage, (d) feed flow rate of fresh water, (e)
reflux flow rate.
9. Conclusions
Synthesis, design and operation of the high-purity ethylene gly-
col reactive distillation column has been studied in this work, and
the following remarks have been reached on the reinforcement of
internal heat integration between the reaction operation and the
separation operation involved.
In the aspect of process synthesis and design, seeking further in-
ternal heat integration between the reaction operation and the sep-
aration operation involved enhances the thermodynamic efficiency
substantially in addition to a further reduction of capital investment.
Although the reaction system displays extremely unfavorable physic-ochemical properties (e.g., the fairly large relative volatility between
the reactants: EO and H2O) and a very high specification of reaction
selectivity (i.e., X EG /X DEG = 19.19), no special restrictions have been
encountered in the reinforcement of internal heat integration be-
tween the reaction operation and the separation operation involved,
demonstrating its high reliability and applicability to the synthesis
and design of reactive distillation columns involving reactions with
high thermal effect.
In the aspect of process dynamics and operation, seeking further
internal heat integration between the reaction operation and the
separation operation involved improves the process dynamics and
lessens the difficulties in process operation. The stringent specifica-
tion of the reaction selectivity poses no limitation on such improve-
ment and the intensified synergism between the reaction operation
and the separation operation involved still accounts for the simulta-
neous improvement in process design and operation.
Although these outcomes have been derived in terms of the high-
purity ethylene glycol reactive distillation column, they are consid-
ered to be of general significance to any other complicated reactive
distillation columns with a high reaction selectivity. It is the resul-
tant coordinated relationship between the reaction operation and
the separation operation involved that provides additional flexibility
for keeping the process innovation from violating the given reaction
selectivity. Current work is now underway to ascertain systemati-
cally this corollary with other kinds of reactive distillation columns
involving reactions with high thermal effect.So far, synthesis, design and operation of reactive distilla-
tion columns involving reactions with high thermal effect (i.e.,
HR / HV >1.0) have been exclusively studied in our work.
For the reactive distillation columns involving reactions with
considerably (i.e., 0.05HR / HV 1.0) or negligibly/no (i.e.,
0HR / HV <0.05) thermal effect, however, relatively few studies
have been performed. For these processes, internal mass integra-
tion should be considered either simultaneously with the internal
heat integration or exclusively between the reaction operation and
the separation operation involved in process synthesis and design.
Similar to the concept of internal heat integration, internal mass
integration signifies the impact of mass coupling between the re-
action operation and the separation operation involved upon the
thermodynamic efficiency of a reactive distillation column. Prudent
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 11/12
3508 F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509
Time [h] Time [h]
0.936
0.944
0.952
0.96
0.34
0.36
0.38
0.4
0.42
0.44
X E G [ m o l e f r a c t i o n ]
X w
[ m o l e f r a c i t o n ]
500
550
600
650
700
750
26
26.4
26.8
27.2
27.6
Time [h] Time [h]
V n
[ k m o l / h ]
F w
[ k m o l / h ]
600
650
700
750
800
Time [h]
R R [ k m o l / h ]
+0.01
–0.01
+0.01
–0.01
–0.01
+0.01
+0.01
–0.01
+0.01
–0.01
–0.01
+0.01
–0.01
+0.01
0 4 8 12 16 20
0 4 8 12 16 20 0 4 8 12 16 20
0 4 8 12 16 20
0 4 8 12 16 20
Fig. 12. Servo responses of the high-purity ethylene glycol reactive distillation columns with and without further internal heat integration when they have been upset
by a ± 0.01 step change in the set-point of bottom control loop, respectively: (a) composition of ethylene glycol in the bottom product, (b) bottom vapor flow rate, (c)
composition of water on the sensitive stage, (d) feed flow rate of fresh water, (e) reflux flow rate. Grey curves: negative responses; black curves: positive responses.
consideration of internal mass integration is also likely to reduce
capital investment and utility consumption, simultaneously. Prin-
ciples for the reinforcement of internal mass integration should
be derived and it is meaningful to see whether the single-variable
based searching method is still feasible in these situations. Our re-
cent work has demonstrated the utmost importance of deepening
internal mass integration during the synthesis and design of reac-
tive distillation columns involving reactions with negligible or no
thermal effect (Sun et al., 2008).
Notation
B bottom withdrawal, kmols−1
CC composition controller
dW time-delay of responses of water composition on the sen-
sitive stage to the changes in water flow rate, s
f detuning factor
F feed flow rate of reactants, kmols−1
FC flow rate controller
HR heat of reaction, kJ kmol−1
HV heat of vaporization, kJ kmol−1
K c proportional gain
K eq vapor–liquid equilibrium constant
K L static gain of responses of bottom EG composition to the
changes in reflux flow rate
K V static gain of initial inverse responses of bottom EG com-
position to the changes in vapor flow rate
K W static gain of responses of water composition on the sen-
sitive stage to the changes in water flow rate
L liquid flow rate, kmol s−1
LC level controller
n1 number of stages
n2 movement of feed location
n number of stages
PC pressure controller
r reaction rate, kmol s−1
RR reflux rate, kmol s−1
S symbol of Laplace transformation
T temperature, K
T I integral time, sT L time constant of responses of bottom EG composition to
the changes in reflux flow rate, s
T V time constant of initial inverse responses of bottom EG
composition to the changes in vapor flow rate, s
T W time constant of responses of water composition on the
sensitive stage to the changes in water flow rate, s
V vapor flow rate, kmol s−1
X liquid composition
Z feed composition
Subscripts
DEG diethylene glycol
EO ethylene oxide
8/4/2019 Integration in Design of Reactive Distillation Columns
http://slidepdf.com/reader/full/integration-in-design-of-reactive-distillation-columns 12/12
F. Zhu et al. / Chemical Engineering Science 64 (2009) 3498 -- 3509 3509
EG ethylene glycol
r rectifying section
rea reactive section
s stripping section
W water
ZN Ziegler–Nichols settings
Acknowledgments
The project is financially co-supported by The National Science
Foundation of China (Grant number: 20776011) and The Scientific
Research Foundation for the Returned Overseas Chinese Scholars,
State Education Ministry.
References
Agrawal, R., Herron, D.M., 1998. Efficient use of an intermediate reboiler or condenserarrangement in a binary distillation. A.I.Ch.E. Journal 44, 1303–1315.
Al-Arfaj, M.A., Luyben, W.L., 2002. Control of ethylene glycol reactive distillationcolumn. A.I.Ch.E. Journal 48, 905–908.
Almeida-Rivera, C.P., Swinkels, P.L.J., Grievink, J., 2004. Designing reactive distillationprocesses: present and future. Computers and Chemical Engineering 28,1997–2020.
Baur, R., Higler, A.P., Taylor, R., Krishna, R., 1999. Comparison of equilibrium stage
and non-equilibrium stage models for reactive distillation. Chemical Engineering Journal 76, 33–47.
Baur, R., Higler, A.P., Taylor, R., Krishna, R., 2001. Dynamic behavior of reactivedistillation columns described by non-equilibrium stage models. ChemicalEngineering Science 56, 2085–2102.
Cardoso, M.F., Salcedo, R.L., Azevedo, S., Barbosa, D., 2000. Optimization of reactivedistillation processes with simulated annealing. Chemical Engineering Science55, 5059–5078.
Chen, F., Huss, R.S., Malone, M.F., Doherty, M.F., 2000. Simulation of kinetics effectsin reactive distillation. Computers and Chemical Engineering 24, 2457–2472.
Chen, F., Huss, R.S., Malone, M.F., Doherty, M.F., 2002. Multiple steady states inreactive distillation: kinetics effects. Computers and Chemical Engineering 26,81–93.
Ciric, A.R., Gu, D., 1994. Synthesis of non-equilibrium reactive distillation processby MINLP optimization. A.I.Ch.E. Journal 40, 1479–1487.
Ciric, A.R., Miao, P., 1994. Steady state multiplicities in an ethylene glycolreactive distillation column. Industrial and Engineering Chemistry Research 33,2738–2748.
Corrigan, T.E., Miller, J.H., 1968. Effect of distillation on a chemical reaction. Industrialand Engineering Chemistry Process Design and Development 7, 383–384.
Fonyo, Z., 1974. Thermodynamic analysis of rectification: I. Reversible model of rectification. International Chemical Engineering 14, 18–27.
Heath, J.A., Kookos, I.K., Perkins, J.D., 2000. Process control structure selection basedon economics. A.I.Ch.E. Journal 40, 1998–2016.
Huang, K., Iwakabe, K., Nakaiwa, M., Tsutsumi, A., 2005. Towards further internalheat integration in design of reactive distillation columns—part I: the designprinciple. Chemical Engineering Science 60, 4901–4914.
Huang, K., Nakaiwa, M., Tsutsumi, A., 2006. Towards further internal heat integrationin design of reactive distillation columns—part II: the process dynamics andoperation. Chemical Engineering Science 61, 5377–5392.
Huang, K., Matsuda, K., Iwakabe, K., Takamatsu, T., Nakaiwa, M., 2006. Graphicalsynthesis of an internally heat-integrated distillation column. Journal of ChemicalEngineering of Japan 39, 703–708.
Huang, K., Wang, S.J., Shan, L., Zhu, Q., 2007. Seeking synergistic effect—a key principlein process intensification. Separation and Purification Technology 57, 111–120.
Huang, K., Wang, S.J., Ding, W., 2008. Towards further internal heat integration indesign of reactive distillation columns—part III: application to a MTBE reactivedistillation column. Chemical Engineering Science 63, 2119–2134.
Huang, K., Zhu, F., Ding, W., Wang, S.J., 2009. Control of a high-purity ethylene glycolreactive distillation column with insights of process dynamics. A.I.Ch.E. Journal
(in press).Ismail, S.R., Proios, P., Pistikkopoulos, E.N., 2001. Modular synthesis framework forcombined separation/reaction systems. A.I.Ch.E. Journal 47, 629–649.
Jackson, J.R., Grossmann, I.E., 2001. A disjunctive approach for the optimal designof reactive distillation columns. Computers and Chemical Engineering 25,1661–1673.
Kumar, A., Daoutidis, P., 1999. Modeling, analysis and control of ethylene glycolreactive distillation column. A.I.Ch.E. Journal 45, 51–68.
Lee, J.W., Hauan, S., Westerberg, A.W., 2000. Graphical methods for reactiondistribution in a reactive distillation column. A.I.Ch.E. Journal 46, 1218–1233.
Lima, R.M., Salcedo, R.L., Barbosa, D., 2006. SIMOP: efficient reactive distillationoptimization using stochastic optimizers. Chemical Engineering Science 61,1718–1739.
Malone, M.F., Doherty, M.F., 2000. Reactive distillation. Industrial and EngineeringChemistry Research 39, 3953–3957.
Melles, S., Grievink, J., Schrans, S.M., 2000. Optimization of the conceptual designof reactive distillation columns. Chemical Engineering Science 55, 2089–2097.
Monroy-Loperena, M., Alvarez-Ramirez, J., 1999. On the steady state multiplicitiesfor an ethylene glycol reactive distillation column. Industrial and Engineering
Chemistry Research 38, 451–455.Monroy-Loperena, M., Perez-Cisneros, E., Alvarez-Ramirez, J., 2000. A robust PI
control configuration for a high-purity ethylene glycol reactive distillationcolumn. Chemical Engineering Science 55, 4925–4937.
Naka, Y., Terashita, M., Hayashiguchi, S., Takamatsu, T., 1980. An intermediate heatingand cooling method for a distillation column. Journal of Chemical Engineeringof Japan 13, 123–129.
Nakaiwa, M., Huang, K., Endo, A., Ohmori, T., Akiya, T., Takamatsu, T., 2003. Internallyheat-integrated distillation columns: a review. Chemical Engineering Researchand Design 81A, 162–177.
Okasinski, M.J., Doherty, M.F., 1998. Design method for kinetically controlled stagedreactive distillation columns. Industrial and Engineering Chemistry Research 37,2821–2834.
Papalexandri, K.P., Pistikopoulos, E.N., 1996. Generalized modular representationframework for process synthesis. A.I.Ch.E. Journal 42, 1010–1032.
Petlyuk, F.B., Platonov, V.M., Girsanov, L.V., 1965. The design of optimal rectificationcascades. International Chemical Engineering 5, 309–317.
Scenna, N.J., Benz, S., 2003. Start-up operation of reactive columns with multiplesteady states: the ethylene glycol case. Industrial and Engineering ChemistryResearch 42, 873–882.
Stein, E., Kienle, A., Esparta, A.R.J., Mohl, K.D., Gilles, E.D., 1999. Optimizationof a reactor network for ethylene glycol synthesis—an algorithmic approach.Computers and Chemical Engineering 23, S903–S906.
Sun, J., Huang, K., Wang, S., 2008. Deepening internal mass integration in designof reactive distillation columns, 1: principle and procedure. Industrial andEngineering Chemistry Research 48, 2034–2048.
Taylor, R., Krishna, R., 2000. Modeling reactive distillation. Chemical EngineeringScience 55, 5183–5229.
Recommended