View
2
Download
0
Category
Preview:
Citation preview
Instruction ManualMalanda/Avalon
1200x900(8mm)
1
With Decina's Exclusive EZI Clean Coating
- The use of harsh or abrasive cleaners will cause deterioration of the EZI�Clean
coating. If water alone is not enough to clean the glass, Decina recommends the
use of mild detergent solutions only.
Utility Knife
- Please read this entire instruction book before commencing installation.
- A licenced tradesman must be used for the installation.- Ensure there is a gasket between all glass and metal components.- Leave the plastic protectors on the glass corners until the last possible momentand handle with care.- Instructions to install the shower tray are included with the shower tray.- In cold climates, warming the gaskets and seals with hot water or a hairdryer willassist installation.
- On symmetrical pieces of glass, the EZI�Clean coating is only on one face. This
face will have a sticker on it to identify it. This side must be installed on the wet
side of the shower.
Cutting Pliers
6mm (1/4") and3mm (1/8") Drill Bits
* Use the correct type of drill bit for the material being drilled, with 6mm required for anchor fixing and 3mm used forscrewing directly into the wall studs.
Safety Goggles Gloves
**
As with all toughened glass, take care while handling and wear safety goggles and gloves for personal protection.
Silicone Sealant Drill Level Rubber Mallet
Pencil Phillips Screwdriver Tape Measure
2
Important Pre-Installation Information
Maintenance
Tools Required
3
a4. Roller wrench tool x2pcs
Screen
9 10 12
17
18
19
20
s4
1
1
2
3
4
5
6
7
22
23
24
1311
14
15
16
8
s5
s6
s7
s8
s3s2
s9
s12
s1
s11
s10
Return Panel
s13
Parts List
1. Channel Cap2. Wall Channel3. Wall Channel Gasket4. Front Panel Glass5. Wall Anchor6. Hinge Side Door Gasket(1918mm)
7. Hinge Side Door Gasket(1912mm)
8. Phillips Head Screw ST4x409. Rail10. Door Glass11. Handle12. Wall bracket base
13. Magnet profile14. Magnetic Door Seal(1988mm)15. Magnetic Door Seal(2000mm)16. Cap L/R17. Countersunk Philip head screw18. guideL/R
20. Long Drip Strip21. Threshold22. Squeeze gasket tool23. Glass Wedge spacer
1 pcs1 pcs1 pcs1 pcs11 pcs1 pcs1 pcs10 pcs1 pcs1 pcs1 pcs1 pcs
1 pcs1 pcs1 pcs1 pcs1 pcs1 pcs
1 pcs1 pcs1 pcs2 pcs
24. Allan key kit2.5mm/3mm 1 pcs
s1. Magnet strip
s2. Chrome kit for bar
s3. Side Panel Glass
s4. Channel Cap
s5. Wall Channel
s6. Wall Channel Gasket
s7. Wall Anchor
s8. Phillips Head Screw ST4x40
s9. Screw cap
s10. Countersunk Philip head screw
s11. 90°Bottom Clamp L/R
s12. Gasket
1 pcs
1 pcs
1 pcs
1 pcs
1 pcs
1 pcs
5 pcs
4 pcs
2 pcs
1 pcs
1 pcs
1 pcs
s13. Glass Wedge spacer
21
19. Gasket 1 pcs
2 pcs
Malanda: Round Roller Avalon: Square Roller
a1. Rollerx2pcs
a3. Roller bumperx1pcs
a2. Fixing plate x2pcs b1. Roller x2pcs
b2. Fixing plate x2pcs
b5. Roller wrench tool x2pcs
b3. Fixing plate cap x2pcs
b4. Roller bumperx1pcs
4
When commencing step 1 on the following page, please refer to this drawing and the tabulated
dimensions for your size of system to assist in the correct location of the wall channels.
SHOWERWALL
FRONT OFSHOWER
SHOWERDOOR
- Locate the size of your shower screen in column 1 and use the value for X and Y on the same line
to find the distance from the shower wall to the outside edge of the wall channels. If a shower base is
fitted, do not measure from the edge of the shower base to determine the position of the wall channel.
- If your wall and shower base are not at right angles the glass will not push fully into the wall channel
at the top or bottom. This misalignment is acceptable if not exceeding 15mm, however the overall
shower size will then increase by the amount of this misalignment.
- If the screen footprint does not turn out square while the aluminium braces are being installed (step
3), the glass can be pulled out from the full depth of the channel by up to 15mm to assist in squaring.
Size
X
(Wall to outside of wall channel)
Screen X
(mm)
1200 1154-1178
OPTIONALSHOWERBASE
Determining Wall Channel Location
1
¼" (Ø6mm)
1B
1C
1D
1E
1A
5
2
2A 2B
2C 2D 2E
2F 2G 2H
OR
2
2
4
5
8
9
9
12
23
24
a2 b2
b3
6
Inside door
±13mm+0 mm
-12mm
3E
3
4
3B
3C
3D
3A
4A LH
RH
a
4C
b
4D
4E 4F 4G
4H 4I 4J 4K
4B
b
3
3
16
17
1819
2021
22
7
5
6
Inside door5B
Inside door5C
5E
Inside door
Inside door
A22
5A OR
OR
OR
Inside door
6A
6B
Inside door
6C
OR
10
14
a1
a4
b1
b5
7
8
8
7A
OR
7B
7C
7D
7E
¼" (Ø6mm)
4X
Inside door
Inside door
Inside door
8A 8B
8C 8D
8E 8F
8G 8H6
7
11
13
15
a3
b3
b4
Inside door
b2
R11 Fixing plate:
9
24 hSILICONE
Silicone inside and outside ofthe shower (silicone notsupplied).
9
1
When commencing step 1 on the following page, please refer to this drawing and the tabulated
dimensions for your size of system to assist in the correct location of the wall channels.
SHOWER
WALL
FRONT OF
SHOWER
SHOWER
DOOR
- Locate the size of your shower screen in column 1 and use the value for X and Y on the same line
to find the distance from the shower wall to the outside edge of the wall channels. If a shower base is
fitted, do not measure from the edge of the shower base to determine the position of the wall channel.
- If your wall and shower base are not at right angles the glass will not push fully into the wall channel
at the top or bottom. This misalignment is acceptable if not exceeding 15mm, however the overall
shower size will then increase by the amount of this misalignment.
- If the screen footprint does not turn out square while the aluminium braces are being installed (step
3), the glass can be pulled out from the full depth of the channel by up to 15mm to assist in squaring.
X
(Wall to outside of wall channel)
OPTIONAL
SHOWER
BASE
Determining Wall Channel Location
10
SIDE OF
SHOWER
Y
(Wall
too
uts
ide
of
wa
llch
annel)
Size
Screen X
(mm)
1200 x 900
Y
(mm)
854-8781154-1178
1
2
¼" (Ø6mm)
1B
1C
1D
1E
11
±13mm
+12mm-0mm
OR
2A 2B
2C 2D
2E 2F
s2
s3
s3
s52
s75
s88
s13
3
4
12
Inside door
±13mm
LHRH
44
RH LH
b
a
b
4B
4D
4F 4G
4H 4I 4J 4K
3A 3B
3C
3D
a
4A
4C
4E
s63
s9
s10
s11
s12
13
5
6
Inside door
6A
6B
Inside door
6C
OR
Inside doorb3
Inside door5B
Inside door5C
5E
Inside door
Inside door
A22
5A OR
OR
OR
10
14
a1
a4
b1
b5
R11 Fixing plate:
b2
14
7
8
7A
OR
7B
7C
7D
7E
8A
8B
8D
8C
Inside door8E
s1
Inside door
15
9
24 hSILICONE
Silicone inside and outside ofthe shower (silicone not
s4
Recommended