View
216
Download
2
Category
Preview:
Citation preview
INSTALLATION MANUAL
ELPMBUNI
EPSON AMERICA, INC.
INDIANAPOLIS DISTRIBUTION CENTER 2350 Stafford Road Suite 101
Plainfield, IN 46168 IN-ELPMBUNI.R3
ELPMBUNI
Installation Instructions Page - 3 -
Table of Contents Warranty ............................................................................................................................................................................................... - 3 - Contact Premier Mounts ....................................................................................................................................................................... - 3 - Warning Statements .............................................................................................................................................................................. - 4 - Parts List ............................................................................................................................................................................................... - 5 - Installation Tools .................................................................................................................................................................................. - 5 - ELPMBUNI Universal Mount Assembly ............................................................................................................................................. - 6 - Projector Preparation ............................................................................................................................................................................ - 7 - Securing the Bracket to the Projector ................................................................................................................................................... - 9 - Leveling the Mounting bracket ........................................................................................................................................................... - 14 - Securing the Upper Assembly Ceiling Plate....................................................................................................................................... - 15 - Low-Profile Installation ...................................................................................................................................................................... - 16 - Securing the Projector to the Upper Assembly ................................................................................................................................... - 18 - Final Adjustments ............................................................................................................................................................................... - 19 - Installing the Plastic Caps................................................................................................................................................................... - 20 - Warranty
Limited Lifetime Warranty
All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. DISCLAIMER OF WARRANTY THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Contact Premier Mounts In the event of missing and/or damage equipment, or technical questions, the following information can help in the completion of the installation. Customer Service – (800) 368-9700 Technical Support – techsupport@mounts.com
ELPMBUNI
Page - 4 - Installation Manual
Warning Statements WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE
USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
WARNING: THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING A MAX
WEIGHT OF 25 LBS., THE WEIGHT OF THE PROJECTOR. IF NOT, THE CEILING MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY QUALIFIED PERSONNEL AS OUTLINED IN THE INSTALLATIONS INSTRUCTIONS MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY.
WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.
Indicates that the power plug is to be disconnected from the power outlet.
Contact Premier Mounts with any questions – (800) 368-9700.
Safety precautions must be taken at all times.
Warning and Caution statements.
A secure structure must support the weight, or load, of the projector. When mounting to a ceiling that contains wooden studs, dead center of the wooden stud must be confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the projector and/or damage to the mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the projector and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the projector.
Recommended mounting surfaces: wooden studs, solid-flat concrete, and reinforced metal studs. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available).
ELPMBUNI
Installation Manual Page - 5 -
Parts List NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of
these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700).
Upper Assembly (Qty 1)
Mounting Bracket (Qty 1)
Plastic Barrel Caps (Qty 4)
M3 Flat Washers (Qty 4)
Note: Must be used with the M3 x 16 Phillips screws.
Lag Screws (#14 x 2”)
(Qty 3)
M4 x 12 Security
Head Screws (Qty 4)
M3 x 16mm Phillips Head
Screws (Qty 4)
NOTE: The following hardware is included in the hardware pack but is not required for the installation. M5 x 12mm Security Head Screws (Qty 4) M6 x 12mm Security Head Screws (Qty 4)
Installation Tools Phillips Head Screw Driver Portable Drill Soft Material/ Blanket Pencil Allen Wrench (Supplied) Level (Supplied) Tape Measure Stud Finder (Commercially Available) Ladder M5 Allen Wrench NOTE: Mounting screws will vary by projector. Please see the following pages for model specific hardware:
Pages 10, 11, 12, and 13.
ELPMBUNI
Page - 6 - Installation Manual
ELPMBUNI Universal Mount Assembly A Single Wooden Stud
Mounting Points B Solid Structure Mounting
Points C Ceiling Plate D Allen Wrench E Height Adjustment Screws F Tension Knobs G Safety Knob H Security Screws I Leveling Barrels J Universal Mounting Bracket K Leg Assembly L Projector (Not Supplied) M Tri-Lock Opening
Option 1
Option 2
Combination Leg
Single Leg
NOTE: See the best configuration for your projector for filter and lamp access.
NOTE: The four (2-piece) leg assemblies can be used as single leg or any combination of single and dual legs together as shown in Options 1 and 2. The number of legs may vary depending on the number of mounting points found on the bottom of your projector.
F
E
L
H
K
B
G D
A
J
C
I
M
D
J
M
L
ELPMBUNI
Installation Manual Page - 7 -
Projector Preparation WARNING: Proper installation procedure by qualified personnel as outlined in the installation instructions
must be adhered to. Failure to do so could result in serious personal injury and possible damage to the projector.
CAUTION: THE PROJECTOR IS FRAGILE; HANDLE WITH CARE AT ALL TIMES. NOTE: Review the projectors manufacture’s operation manual and refer to the ceiling installation
instruction. Here you will normally find important reference information regarding installation dimensions such as (distance from the screen to the lens of the projector, top of the lens placement to the top screen etc. Adherence to these recommendations during your installation will enhance the quality of your final image on the screen.
1. Carefully invert the projector and place it on a smooth flat surface. 2. Identify the number of mounting points and screw thread (pitch) size. 3. Most projectors have either three or four mounting points and are M4 in thread size (Figure 1).
Figure 1
Inverted Projector
Flat surface
Mounting Points
Blanket, soft cloth etc
ELPMBUNI
Page - 8 - Installation Manual
4. Separate the upper assembly from the projector mounting bracket by slightly loosening the two tension knurl knobs to create free play between the bracket tri-lock assembly and the upper section tri-lock assembly points.
5. Next loosen the safety screw knurl knob far enough to allow the two parts to be rotated 180° apart and separate.
Figure 2 Figure 3
Figure 4
Tension Knobs
Upper Assembly
Safety Knob
Tri-Lock Opening
Rotate 180° To Unlock
ELPMBUNI
Installation Manual Page - 9 -
Securing the Bracket to the Projector NOTE: The two-piece mounting legs are designed to allow routing of the legs around critical ventilation
screens on the base of the projector as shown. You may also reduce the two-piece leg to a one-piece leg as shown for a better overall fit to the projector.
1. Locate the mounting points on the bottom of the projector and use the appropriate number of mounting
legs. 2. Select the mounting hardware that your projector requires and loosely install the universal mount to your
projector. NOTE: If your projector requires M3 mounting hardware. Use the M3 x 16 Phillips screws with the M3
flat washers (supplied). Insert the M3 x 16 Phillips screws with the flat washers attached through the leveling barrel. Using a Phillips screwdriver, loosely secure the screws to the projector (Figure A).
NOTE: The levelers and leg assembly screws must be loose in order to adjust the height of the mounting
bracket.
Figure 5
FIGURE A
FIGURE 7 One-Piece Leg
FIGURE 6
Two-Piece Leg
Leveling Barrels
Mounting Hardware
Allen Wrench
Inverted Projector
Line up the leveling barrels to the mounting points.
ELPMBUNI
Page - 10 - Installation Manual
NOTE: If your projector model is not shown, when arranging the leg combination, simply ensure access to filters and lamp housings when aligning brackets. This mount works with all sub-25 pound projectors.
PowerLite S3, S4, 62C, 76C, 82C, Hardware: M4 x 12mm (Qty 3)
PowerLite 830p, 835p
Hardware: M4 x 12mm (Qty 4)
ELPMBUNI
Installation Manual Page - 11 -
PowerLite 732c, 737c, 740C, 745C, 750c, 755c, 760c, 765c
Hardware: M4 x 12mm (Qty 3)
Top View
Front View
ELPMBUNI
Page - 12 - Installation Manual
PowerLite 7800p, 7850p, 7900p Hardware: M4 x 12mm (Qty 4)
PowerLite 61p, 81p, 821p
Hardware: M4 x 12mm (Qty 4)
ELPMBUNI
Installation Manual Page - 13 -
PowerLite S1, S1+
Hardware: M4 x 12mm (Qty 3)
PowerLite 6100i
Hardware: M4 x 12mm (Qty 4)
ELPMBUNI
Page - 14 - Installation Manual
Leveling the Mounting bracket 1. Rotate the leveling barrels to level the mounting bracket next, position the mounting bracket so that it
avoids most, if not all, ventilation points (including lamp & filter access doors). 2. When the position desired is achieved tighten the mounting hardware to the projector then tighten the hex
head leg screws with the Allen wrench (supplied) (Figure 8 and Figure 9).
CAUTION: Secure but do not over-tighten the mounting hardware. Failure to do so will result in damaging the threads in the projector.
UP
DOWN
Figure 8
Level
Allen Wrench
Leveling Barrels
Inverted Projector
Adjusting the Mount
ELPMBUNI
Installation Manual Page - 15 -
Securing the Upper Assembly Ceiling Plate 1. Review your projector’s distance calculation to determine what distance is recommended from the front of
the lens to the edge of the screen for best picture ratio. 2. Locate the inverted projectors top of the lens point to a point centered horizontally on the screen and no
higher then the top image edge of the screen). 3. It is normally better to have the top edge of the lens as close to parallel with the top image edge of the
screen as well. 4. Before you mount your screen and projector, make sure the mounting location will safely support the
weight of the projector. NOTE: Make sure to measure from the center of the mounting bracket to the front edge of the lens to
determine the proper placement of the center of the upper assembly.
NOTE: If installing the security kit (ELPMBSEC), please refer to the security kit installation guide before attaching the ceiling plate to the ceiling or wall.
5. Secure the ceiling assembly into a solid wood ceiling stud with the three (3) #14 x 2” wood screws
(supplied) or with other (commercially available) hardware depending on your installation environment (Figure 9).
Figure 9
Secure the ceiling mount to the center of the wood stud.
Ceiling Structure
Wood Screws
Upper Assembly
Knurl Knobs (3ea)
Ceiling Wood Stud
ELPMBUNI
Page - 16 - Installation Manual
Low-Profile Installation 1. If your installation requires the overall height of the mount to be less that the approximate 9” shown with
the standard mount assembly, you can convert the height to only 2 ½” by simply removing the adjustment channel as shown.
2. Once the extension channel is removed, attach the upper ceiling plate to the ceiling. 3. Once attached install the bell housing assembly to the upper ceiling plate as shown (Figure 10, Figure 11,
and Figure 12).
Figure 10
Ceiling Plate
Remove the M8 x 16mm Screws, flat Washers and Star Washers
Allen Wrench
Remove the Middle Extension Completely
Remove the M8 x 16mm Screws, Flat Washers, and Star Washers (Both Sides)
Remove the M8 x 16mm Screws, Flat Washers, and Star Washers (Both Sides)
Bell Housing
ELPMBUNI
Installation Manual Page - 17 -
Figure 11
Figure 12
NOTE: Do not use the star washers on a close ceiling application.
Wood Stud
Ceiling Structure
Ceiling Plate
Wood Screws
Wood StudCeiling Structure
Secure the Bell Housing with Two M8 x 16mm Screws and Flat Washers Only
Attach Bell Housing to the Ceiling Plate
Allen Wrench
ELPMBUNI
Page - 18 - Installation Manual
Securing the Projector to the Upper Assembly 1. Make sure the three-knurl knobs are loosened to fully expose to the “tri-lock” mounting plate in the base
of the upper assembly. 2. Carefully lift the projector and insert the mounting bracket mating special tri-lock cutout into the mating
portion of the upper assembly. 3. Once inserted rotate the projector and mounting bracket 180° and secure the rear safety knob first to
prevent further rotation of the bracket in the upper assembly. 4. Tighten the remaining two tension knurl knobs until the mount becomes rigid. 5. The safety knob should line up with the alignment slot on the mounting bracket (Figure 13).
NOTE: Follow the number sequence prior to securing the projector to the upper assembly.
Figure 13
The alignment slot must be in direct alignment with the safety knob to lock the mounting bracket to the upper assembly
Universal Mount
Alignment Slot
Tri-Lock Opening
Projector Mount
Tension Knurl Knobs
Safety Knurl Knob
Insert universal bracket to the tri-lock, then rotate the projector 180°
ELPMBUNI
Installation Manual Page - 19 -
Final Adjustments 1. With the projector secured in the mount and power on and signal supplied to the projector you can now
proceed with the final height, tilt, and roll and yaw to optimize the projected image. 2. The height can be adjusted by slightly loosening the two 8mm height adjustment screws and raising or
lowering the projector (Figure 14). 3. Once the height is achieved tighten the two screws. 4. To adjust the tilt angle of the projector, slightly loosen the side M8 screws and tilt to the desired angle to
the screen and firmly tighten the two M8 tilt adjustment screws (Figure 15). 5. If roll adjustment is needed to square the images on the screen, slightly loosen the front and rear M8
screws and adjust to the desired angle then firmly tighten the two M8 roll adjustment screws (Figure 16).
Figure 14
Figure 15
Figure 16
Wood Stud
Ceiling
(Roll) Adjusting Screws
Allen Wrench
Allen Wrench
Wood Stud
Ceiling
Tilt Adjusting Screws
Wood Stud
Allen Wrench Height Adjustable Screws
Ceiling
ELPMBUNI
Page - 20 - Installation Manual
Installing the Plastic Caps 1. Once all the final adjustments have been done, install the plastic caps on the leveling barrels
(Figure 17).
Figure 17
Recommended