View
230
Download
10
Category
Preview:
Citation preview
IEC inlet iltersFN 9222
General performance IEC inlet ilter
Approvalsn Rated currents up to 20A
n Excellent performance/size ratio
n Optional medical versions (B type)
n Snap-in versions (S and S1 type)
n Hot inlet versions (HI type)
Typical applications
The FN 9222 IEC inlet filter combines an
IEC inlet and mains filter with excellent filter
attenuation in a small form factor. Choosing
the FN 9222 product line brings you the rapid
availability of a standard filter associated with
the necessary safety acceptances. Standard
IEC connector filters are a practical solution
helping you to pass EMI system approval in
a short time. A wide selection on amperage
ratings, output connections, mounting
possibilities and filters for medical applications
are designed to offer you the desired solution.
n Exceptional conducted attenuation
performance, based on chokes with high
saturation resistance and excellent thermal
behavior.
n Rear/front or snap-in mounting.
n Optional low leakage currents for medical
applications.
n 12 and 15A types with hot inlet available.
n Different output connections offering
maximum flexibility for assembly.
n Custom-specific versions are available on
request.
n Portable electrical and electronic
equipment
n Small to medium sized machines and
household equipment
n Single-phase power supplies, switch mode
power supplies
n Test and measurement equipment
n Medical systems
n Rack mounting equipment
Features and benefits
Technical specifications
Maximum continuous operating voltage: 250VAC, 50/60Hz
Operating frequency: dc to 400Hz
Rated currents: 1 to 20A @ 50°C
Approvals by rated current:
1 to 10A types: 1 to 10A (ENEC, UL, CSA, CQC)
12 and 15A types: 10A (ENEC), 12 to 15A (UL, CSA, CQC)
16 and 20A types: 16A (ENEC), 16 to 20A (UL, CSA)
High potential test voltage: P –> E 2000VAC for 2 sec (standard types)
P –> E 2500VAC for 2 sec (B types)
P –> N 1000VAC for 2 sec (1 to 10A types)
P –> N 1100VDC for 2 sec (16 and 20A types)
Protection category: IP40 according to IEC 60529
Temperature range (operation and storage): -25°C to +85°C (25/85/21)
Design corresponding to: UL 1283, CSA 22.2 No. 8 1986, EN 60939
Flammability corresponding to: UL 94V-2 or better
MTBF @ 40°C/230V (Mil-HB-217F): ≤15A: 3,040,000 hours
≥16A: 2,256,000 hours
Typical electrical schematic
N
E
P
Line
Cx R 2xL 2xCyN‘
E‘
P‘
Load
> Components > FN 9222
* Max. leakage under normal operating conditions. Note: if the neutral line is interrupted, worst case leakage could reach twice this level.
Filter selection table
FN 9222x-1-.. 1 (1.2) 373 12 0.1 2.2 -06 -07 40
FN 9222x-3-.. 3 (3.5) 373 2.5 0.1 2.2 -06 -07 40
FN 9222x-6-.. 6 (7.2) 373 0.78 0.1 2.2 -06 -07 40
FN 9222x-8-.. 8 (10.6) 373 0.4 0.1 2.2 -06 -07 40
FN 9222x-10-.. 10 (11.6) 373 0.225 0.1 2.2 -06 -07 40
FN 9222x-12-.. 12 (12) 373 0.11 0.1 2.2 -06 -07 40
FN 9222x-15-.. 15 (15) 373 0.075 0.1 2.2 -06 -07 40
FN 9222x-12-..HI 12 (12) 373 0.11 0.1 2.2 -06 -07 40
FN 9222x-15-..HI 15 (15) 373 0.075 0.1 2.2 -06 -07 40
FN 9222xR-1-.. 1 (1.2) 373 12 0.1 2.2 1000 -06 -07 40
FN 9222xR-3-.. 3 (3.5) 373 2.5 0.1 2.2 1000 -06 -07 40
FN 9222xR-6-.. 6 (7.2) 373 0.78 0.1 2.2 1000 -06 -07 40
FN 9222xR-8-.. 8 (10.6) 373 0.4 0.1 2.2 1000 -06 -07 40
FN 9222xR-10-.. 10 (11.6) 373 0.225 0.1 2.2 1000 -06 -07 40
FN 9222xR-12-.. 12 (12) 373 0.11 0.1 2.2 1000 -06 -07 40
FN 9222xR-15-.. 15 (15) 373 0.075 0.1 2.2 1000 -06 -07 40
FN 9222xR-16-.. 16 (18.5) 373 0.54 0.33 2.2 1000 -06 100
FN 9222xR-20-.. 20 (23) 373 0.4 0.33 2.2 1000 -06 100
FN 9222xR-12-..HI 12 (12) 373 0.11 0.1 2.2 1000 -06 -07 40
FN 9222xR-15-..HI 15 (15) 373 0.075 0.1 2.2 1000 -06 -07 40
FN 9222xB-1-.. 1 (1.2) 2 12 0.1 1000 -06 -07 40
FN 9222xB-3-.. 3 (3.5) 2 2.5 0.1 1000 -06 -07 40
FN 9222xB-6-.. 6 (7.2) 2 0.78 0.1 1000 -06 -07 40
FN 9222xB-8-.. 8 (10.6) 2 0.4 0.1 1000 -06 -07 40
FN 9222xB-10-.. 10 (11.6) 2 0.225 0.1 1000 -06 -07 40
FN 9222xB-12-.. 12 (12) 2 0.11 0.1 1000 -06 -07 40
FN 9222xB-15-.. 15 (15) 2 0.075 0.1 1000 -06 -07 40
FN 9222xB-16-.. 16 (18.5) 2 0.54 0.33 1000 -06 100
FN 9222xB-20-.. 20 (23) 2 0.4 0.33 1000 -06 100
FN 9222xB-12-..HI 12 (12) 2 0.11 0.1 1000 -06 -07 40
FN 9222xB-15-..HI 15 (15) 2 0.075 0.1 1000 -06 -07 40
Filter Rated current Leakage current* Inductance Capacitance Resistance Output connections Weight
@ 50°C (25°C) @ 250VAC/50Hz L Cx Cy R
[A] [µA] [mH] [µF] [nF] [kΩ] [g]
Product selector
FN 9222xx-yy-..HI-zz
Snap-in range for S version only
Blank: Snap-in range 0.7 to 1.5mm
20: Snap-in range 1.5 to 2.2mm
Blank: Standard IEC inlet type C14 (1 to 15A types), C16 (16 and 20A types)
HI: Hot IEC inlet type C16 (12 and 15A types only)
06: Faston 6.3 x 0.8mm (spade/soldering)
07: Wire leads
1 to 20: Rated current
Blank: Standard version
R: Bleed resistor
B: Medical version (with bleed resistor and without Y2-capacitor)
Blank: Standard housing with mounting langes
S: Snap-in version, snapper on vertical side (1 to 15A types only)
S1: Snap-in version, snapper on horizontal side (1 to 15A types only)
For example: FN 9222-15-07, FN 9222S1B-10-06-20, FN 9222R-12-06HI-20
> Components > FN 9222
Per CISPR 17; A = 50Ω/50Ω sym; B = 50Ω/50Ω asym; C = 0.1Ω/100Ω sym; D = 100Ω/0.1Ω sym
Typical filter attenuation
1 and 3A types 6 to 10A types 12 and 15A types 16 and 20A types
Mechanical data
FN 9222, 1 to 15A types
FN 9222S FN 9222S1
Panel cut out
A C
B
E
G
S
F D I
6.3 x 0.8
J
6.3 x 0.8
J
IDF
B
A
G
E
X
Installation
T
H
A
B
E
G F D I
J
6.3 x 0.8
Y
Z
-07 connection style
C
PR
MN
FN 9222, 16 and 20A types
A C
B
E
G
S
F D I
6.3 x 0.8
J
H
FN 9222-HI
A C
B
E
G
S
F D I
6.3 x 0.8
J
H
> Components > FN 9222
Your local partner: To find your local partner within Schaffner’s global network, please go to www.schaffner.com May 2007
* For selecting the panel thickness, please refer to the filter selection table.
All dimensions in mm; 1 inch = 25.4mm
Tolerances according: ISO 2768 / EN 22768
FN 9222 FN 9222S FN 9222S1 FN 9222-HI
1 to 8A 10 to 15A 16 and 20A 1 to 8A 10 to 15A 1 to 8A 10 to 15A 12 and 15A
Dimensions
A 48 48 53 29.9 29.9 29.9 29.9 48
B 22.5 22.5 30 22.4 22.4 22.4 22.4 22.5
C 40 40 42 40
D 38.4 38.4 66 38.4 38.4 38.4 38.4 38.4
E 27.8 27.8 34 27.8 27.8 27.8 27.8 27.8
F 5.5 5.5 4 5.5 5.5 5.5 5.5 5.5
G 20.1 20.1 26.5 20.1 20.1 20.1 20.1 20.1
H Ø3.3 Ø3.3 Ø3.5 Ø3.3
I 14 14 14 14 14 14 14 14
J 13.3 13.3 13.3 13.3 13.3 13.3 13.3 13.3
M R ≤ 3 R ≤ 3 R ≤ 3 R ≤ 1.5 R ≤ 1.5 R ≤ 1.5 R ≤ 1.5 R ≤ 3
N 21.5 21.5 27 20.8 20.8 21.9 21.9 21.5
P 28.5 28.5 34.7 29.4 29.4 28.5 28.5 28.5
R M3 M3 M3 M3
S 90° 90° 90° 90°
T* 0.7 - 1.5 0.7 - 1.5 0.7 - 1.5 0.7 - 1.5
T* 1.5 - 2.2 1.5 - 2.2 1.5 - 2.2 1.5 - 2.2
X AWG 18 AWG 16 AWG 18 AWG 16 AWG 18 AWG 16 AWG 16
Y 160 160 160 160 160 160 160
Z 6 6 6 6 6 6 6
Recommended