View
2
Download
0
Category
Preview:
Citation preview
as of 17 Mei 2016
Page 1 of 15
I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY
INDONESIA
I. RATIONALE FOR REGULATION
COUNTRY RATIONALE FOR REGULATION
Indonesia Consumer Protection
II. REGULATION BODY
COUNTRY REGULATORY BODY
Indonesia
Ministry of Industry Ministry of Energy and Mineral Resources Ministry of Trade
as of 17 Mei 2016
Page 2 of 15
III. LEGISLATIVE FRAMEWORK
COUNTRY LEGISLATIVE FRAMEWORK
Indonesia 1. Act No. 8 / 1999 concerning Consumer Protection
2. Act No. 3 / 2014 concerning Industry
3. Act No. 7 / 2014 concerning Trade
4. Act No. 20 /2014 concerning Standardization and Conformity Assessment
5. Government Regulation No. 102/2000 concerning National Standardization
6. Decree of the Minister of Industry No. 86/M-IND/PER/9/2009 concerning the Implementation of
SNI in Industrial Sector
7. Decree of the Minister of Industry No. 51/M-IND/PER/3/2012 concerning The Procedures for
Recognition of Certification Product of Electrical and Electronic Equipment Issued by
Conformity Assessment Bodies Listed in ASEAN
8. Decree of the Minister of Energy and Mineral Resorces No. 01/2016 concerning The
Procedures for Recognition of Product Certification and Product Test Report of Electrical and
Electronic Equipment Issued by Conformity Assessment Bodies Listed in ASEAN
9. Decree of the Minister of Trade No. 24/M-DAG/PER/4/2016 concerning Standardization on
Trade Sector
as of 17 Mei 2016
Page 3 of 15
IV. MANDATORY STANDARDS
Product type or grouping
STANDARDS
State reason if MOD
Indicate whether requires:
Safety (S), Environment
(E), EMC, or
combination
Domestic Standards
Please tick box if
mandatory Relevant International Standards
Extent of Alignment
Incandescent lamps
SNI 04-3560-1994 V IEC 60064 Ed.6 (1993-12)
IDT S
Self-ballast lamp for general lighting service SNI 04-6504-2001 V IEC 60968 Ed.1.0 (1988-11)
IDT S
Plugs and socket-outlets for household and similar purposes. Part 1 : General requirement
SNI 04-3892.1-2006 V IEC 60884-1 (2002-06)
IDT S
Switches for household installations and similar fixed electric. Part 1: General requirements
SNI 04-6203.1-2006 V IEC 60669-1 (2000)
IDT S
Circuit breakers for over current protection for household and similar installation. Part 1 : Circuit breaker for a.c operated
SNI 04-6507.1-2002
SNI 04-6507.1-2002/Amd1. 2006
V IEC 60898-1 (2003)
IDT S
Electrical appliances for household usages and other similar types of safety products; Part 2-80. Special requirements for electric fan
SNI 04-6292.2.80-2006 V IEC 60335-2-80(2004-03)
IDT S
Lamp controlgears - Part 1: General and safety requirements
SNI 04-6959.1-2003 V IEC 61347-1 (2000-10) IDT
S
Lamp controlgears - Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps
SNI 04-6959.2.3-2003 V IEC 61347-2-3 (2000-10)
IDT
S
as of 17 Mei 2016
Page 4 of 15
Product type or grouping
STANDARDS
State reason if MOD
Indicate whether requires:
Safety (S), Environment
(E), EMC, or
combination
Domestic Standards
Please tick box if
mandatory Relevant International Standards
Extent of Alignment
Residual current operated circuit - breakers without integral overcurrent protection for household and similar uses (RCCB) - Part 1: General rules
SNI 4 -6956.1-2003 V IEC 61008-1 (1996-12) IDT S
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) - Part 2-1: Applicability of the general rules to RCCB’s functionally independent of line voltage
SNI 04-6956.2.1-2005 V IEC 61008-2-1 (1990-12)
IDT S
Luminaires - Part 1: General requirements and tests
SNI 4 -6973.1-2005 V IEC 60598-1 (2003)
IDT
S
Luminaires - Part 2-1: Particular requirements - Fixed general purpose luminaires
SNI 4 -6973.2.1-2005 V IEC 60598-2-1 (1979) IDT
S
Luminaires - Part 2-2: Particular requirements - Recessed luminaires
SNI 4 -6973.2.2-2005 V IEC 60598-2-2 (1997)
IDT
S
Luminaires - Part 2-3: Particular requirements - Luminaires for road and street lighting
SNI 4 -6973.2.3-2005 V IEC 60598-2-3 (2002)
IDT
S
Luminaires - Part 2-5: Particular requirements – Floodlights
SNI 4 -6973.2.5-2005 V IEC 60598-2-5 (1998): IDT
S
Primary Battery - part 1: General SNI 04-2051.1-2004 V
IEC 60086-1 (2000)
IDT
S
Primary Battery - part 2: Electrical and Physical Requirement
SNI 04-2051.2-2004 V
IEC 60086-2 (2000)
IDT
S
as of 17 Mei 2016
Page 5 of 15
Product type or grouping
STANDARDS
State reason if MOD
Indicate whether requires:
Safety (S), Environment
(E), EMC, or
combination
Domestic Standards
Please tick box if
mandatory Relevant International Standards
Extent of Alignment
PVC insulated cables with a rated voltage up to 450/750 V - Part 3: Non-sheated cables for fixed wiring
SNI 04-6629.3-2006 V IEC 60227-3(1997-11) IDT
S
PVC insulated cables with a rated voltage up to 450/750 V - Part 4: Sheated cables for fixed wiring
SNI 04-6629.4-2006 V IEC 60227-4(1997-12) IDT
S
PVC insulated cables with a rated voltage up to 450/750 V - Part 5: Flexible cables
SNI 04-6629.5-2006 V IEC 60227-5(2003-07) IDT
S
Safety of household and similar electrical appliances — Part 2-41 : Particular requirements for pumps
SNI 04-6292.2.41-2003
V IEC 60335-2-41 (2002-10)
IDT
S
Household and similar electrical appliances – Safety – Part 2-3: Particular requirements for electric irons
SNI 04-6292.2.3-2003 V IEC 60335-2-3 (2002-03)
IDT
S
as of 17 Mei 2016
Page 6 of 15
Product type or grouping
STANDARDS
State reason if MOD
Indicate whether requires:
Safety (S), Environment
(E), EMC, or
combination
Domestic Standards
Please tick box if
mandatory Relevant International Standards
Extent of Alignment
Audio, video and similar electronic apparatus —Safety requirements
SNI 04-6253-2003 V IEC 60065 (2001–12) MOD 4.1.3
Unless
otherwise
specified,
the tests
are carried
out under
normal
operating
conditions
at:
-
anambient
temperatur
e between
20 oC and
35 oC
- a relative
humidity of
70 % ±
15%
maximum
S
as of 17 Mei 2016
Page 7 of 15
Product type or grouping
STANDARDS
State reason if MOD
Indicate whether requires:
Safety (S), Environment
(E), EMC, or
combination
Domestic Standards
Please tick box if
mandatory Relevant International Standards
Extent of Alignment
Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
SNI IEC 60335-2-40:2009 V IEC 60335-2-40 Ed 4.2 (2005-07)
IDT
S
Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers
SNI IEC 60335-2-24:2009
V IEC 60335-2-24 Ed 6.1 (2005-04)
IDT
S
Household and similar electrical appliances - Safety - Part 2-7: Particular requirements for washing machines
SNI IEC 60335-2-7:2009 V IEC 60335-2-7 (2004-11)
IDT
S
as of 17 Mei 2016
Page 8 of 15
V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES
COUNTRY TYPES OF CON-FORMITY ASSESS-
MENT REGIMES
MODE OF REGULATION
Indonesia Technical Regulation based on SNI
Technical regulation on EEE by adopting partially or fully technical specification and/or parameter of SNI is stipulated by Ministerial Decree taking into account safety, security, health, environment, moral hazard, and economical aspects, that are equally imposed to both domestic and imported products which are traded in Indonesian teritory.
Manufacturers of EEE which are technically regulated based on SNI shall fulfill the SNI requirements and shall affix the SNI mark on the products, packages and/or label of their products
Product Registration to get NPB (for imported products) or NRP (for domestic products)
Pre-market surveillance over traded goods produced domestically, shall be done through Product Registration Number (Nomor Registrasi Produk - NRP)
Pre-market surveillance over imported of EEE shall be done through Goods Registration Number (Nomor Pendaftaran Barang – NPB),
NRP and NPB shall be issued by the Director of Standardization and Quality Control, Ministry of Trade
The validity of NRP and NPB are in accordance with the validity period of SPPT SNI.
NRP or NPB shall affix underneath SNI Mark and/or other recognized conformity mark, on to their products or packages.
as of 17 Mei 2016
Page 9 of 15
COUNTRY TYPES OF CON-FORMITY ASSESS-
MENT REGIMES
MODE OF REGULATION
Registration of CAB CAB issuing an SNI Mark Product Certification can be a domestic or foreign product certification body supported by accredited testing laboratories and/or inspection institutions.
Domestic CAB shall be accredited by KAN according to its scopes, CAB shall be
registered to the Directorate of Standardisation and Quality Control, Ministry of Trade.
All CAB which have the scope of mandatory SNI’s requirements shall be accredited by National Accreditation Body of Indonesia (KAN) and assigned by Minister of Industry
as of 17 Mei 2016
Page 10 of 15
VI. FLOWCHART OF INDONESIA’S REGIME
PROCEDURES FOR RECOGNITION OF CERTIFICATES OF ELECTRICAL EQUIPMENTS AND ELECTRONIC PRODUCTS
FROM CONFORMITY ASSESSMENT BODIES IN ASEAN COUNTRIES
AMS Indonesia
Listed Product Certification Body for EEE
Listed Testing Lab. for EEE
Product Certification Body
SPPT SNI according to certification type ISO/IEC 17067
Product EEE ASEAN
Legend: 1. Using Certificate of Conformity issued by Listed Product Certification Body 2. Using Testing report issued by Listed Testing Lab.
Listed Testing lab have to be accredited for full parameter of the standards 3. Direct to listed Indonesia Product Certification Body
Indonesia Product Certification Body may ask for additional requirement if necessary For point 1 & 2 requires a submission of Form D-ATIGA
3
1
2
as of 17 Mei 2016
Page 11 of 15
VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION
Country Mains
Voltage and Tolerance
Mains Frequency and Tolerance
Applicable Legislation
Mains Plug Configuration
Domestic Standard
Please tick box if mandatory
Relevant International Standard
Extent of Alignment -
Diagram of Mains Plug Configuration-
Indonesia 230 5% 50 5% SNI 04-3892.1-2006
Plugs and socket-outlets for household and similar purposes. Part 1 : General requirement
V
IEC 60884-1
Ed.3.0(2002,am.1(2006)
IEC 60884-2-1 Ed.1.0(1987)
IEC 60884-2-3 Ed.1.0(1989) (0nly for the
safety)
SNI 04-3892.2.3-
2000:Plugs and Sockets-Outlets for household and similar purposes;Part 2.3:Particular Requirement for switched socket outlets without interlock for fixed installation.
as of 17 Mei 2016
Page 12 of 15
Country Mains Voltage and Tolerance
Mains Frequency and Tolerance
Applicable Legislation
Mains Plug Configuration
Domestic Standard
Please tick box if mandatory
Relevant International Standard
Extent of Alignment -
Diagram of Mains Plug Configuration-
SNI 04-6202-
2000: Plugs and Sockets-Outlets and couplers for industrial purposes;Part 3: Particular Requirement for plugs, socket outlets, connectors and appliance inlets for use in explosive gas atmospheres.
SNI 04-0225-
2000/Amd1-2006 on Amendment 1 of Indonesian National Standard for General Requirements on Electrical Installation
V IEC 60364 (series)
as of 17 Mei 2016
Page 13 of 15
VIII. MARKING/LOGO :
Affixing SNI and NRP
Note:
101 : Product Certification Body certifying the products 010 : Factory Location 000001 : Registration Number in Directorate of Standardization and Quality Control
as of 17 Mei 2016
Page 14 of 15
Affixing SNI and NPB
Note:
101 : Product Certification Body certifying the products 156 : Country of Origin 000001 : Registration Number in Directorate of Standardization and Quality Control
as of 17 Mei 2016
Page 15 of 15
IX. CONTACT PERSON
Country JSC EEE
Indonesia Representative Officer Chandrini M. Dewi Director of Standardization and Quality Control Directorate General of Consumer Protection and Trade Compliance Ministry of Trade Jl. Raya Bogor KM 26 Ciracas - Jakarta Timur Telp : (021) 8710321/3Fax : 62-21-3863928 E-mail : chandrini.dewi@kemendag.go.id, ks.ditstandalitu@gmail.com Contact Person Konny Sagala, S.Si Head of Center for Cooperation on Standardization - BSN BPPT I Building Jl. M.H. Thamrin No. 8, Kebon Sirih Jakarta Pusat 10340 Indonesia Phone : 62-21-3927422 Fax : 62-21-3927527 E-mail : konny@bsn.go.id, bilreg.bsn@gmail.com Designating Body Dr. Zakiyah Head of Center for Application on Standardization - BSN BPPT I Building Jl. M.H. Thamrin No. 8, Kebon Sirih Jakarta Pusat 10340 Indonesia Phone : 62-21-3927422 Fax : 62-21-3927527 E-mail : zakiyah@bsn.go.id, sps-2@bsn.go.id
mailto:chandrini.dewi@kemendag.go.idmailto:ks.ditstandalitu@gmail.commailto:konny@bsn.go.idmailto:bilreg.bsn@gmail.commailto:zakiyah@bsn.go.idmailto:sps-2@bsn.go.idRecommended