View
241
Download
5
Category
Tags:
Preview:
Citation preview
GE Interlogix
Kalatel Division
Product Update
KTD-405 Programming& Standard Operations
KTD-405 Keypad Programming
KTD-405 keypad (Supervisor Programming)
KEYPAD ADDRESS: 99
KEYPAD 99
Boot-Up Screen
KTD-405 keypad (Supervisor Programming)
CAMERA ---
MONITOR 1
Default display after applying power
KTD-405 keypad (Programming)
Navigating the menus
Key FunctionDisplays the next menu
Displays the previous menu
Scrolls up when indicated by in the menus
Scrolls down when indicated by in the menus
Scrolls right when indicated by in the menus
Scrolls left when indicated by in the menus
Scrolls up, down, left or right when indicated by , , , in the menus
Advances menus; exits menus if held for 3 secondsseq
KTD-405 keypad (Programming)
NOT IMPLEMENTED
Menus that were not available in the first releases of software are indicated by two beeps and the following display:
Supervisor Programming
KTD-405 keypad (Supervisor Programming)
To Access Programming: Press and hold the key
The unit will beep and show the following display
Remote device programming must be accessed separately.
Supervisor programming password is 1,4,7,6,
Also includes All user programming
ENTER PROGRAMMING
CODE:
seq
KTD-405 keypad (Supervisor Programming)
Resetting the Factory Defaults The first menu to display will be this one.
Press to advance to the next menu and to return to the previous menu at any time without changing any existing parameters
RESET TO DEFAULTS? NO
<+>=YES <->=NO NEXT
KTD-405 keypad (Supervisor Programming)
1=RESET ALL BUT TITLES
2=RESET ALL
If you pressed “+” (yes): The next display will show:
Followed by:
Followed by:
The keypad will advance to the next menu automatically
ARE YOU SURE?
<+>=YES <->=NO NEXT
INITIALIZING DEFAULTS
PLEASE WAIT
KTD-405 keypad (Supervisor Programming)
Setting The Keypad Address The address is a “user defined” two-digit number
The address must be from 10 to 99
Each device on the RS-485 network must have a unique address
Address 99 is automatically assigned when the keypad is first connected and will remain unless changed by the user
Entering an address that is already used temporarily displays:
Select or to skip over this menu
KEYPAD ADDRESS: 99
(01-99) NEXT
ADDRESS NOT AVAILABLE
KTD-405 keypad (Supervisor Programming)
Backward Compatibility? If the KTD-405 is being used in a system with:
Existing ProBridges
Existing CBR-KB3 or CBR-KB3/J keypads
Select YES to allow the KTD-405 to communicate properly with these devices.
Select or to skip over this menu
KB3 PTZ PROTOCOL? NO
<+>=YES <->=NO NEXT
KTD-405 keypad (Supervisor Programming)
Allow Remote Programming by user? If the KTD-405 is being used in a system with:
Matrix Switchers or Multiplexers
Alarm Monitoring Equipment
Programmable Dome Cameras or Receivers
Select YES to allow the user to enter the 9,5,1, password and program these devices
Select or to skip over this menu
ENABLE REMOTE PRGMG? YES
<+>=YES <->=NO NEXT
seq
KTD-405 keypad (Supervisor Programming)
Programming Keypad Titles A keypad title can be up to 14 characters including:
A – Z and 0 - 9
Keypads with titles can use the “Seize Control” option
Supervisors can seize camera sites, multiplexers, VCRs, etc.
Supervisors can seize an entire zone in the ZONE mode
Use the joystick or these buttons to program the title
Select or to skip over this menu
KEYPAD TITLE: <>
NEXT
= , = , = , = ,
KTD-405 keypad (Supervisor Programming)
Changing the SEIZE CONTROL code Use the number keys to enter the new code
The keypad will advance to the next menu when the last digit is entered
Select or to skip over this menu
SEIZE CONTROL CODE: 8642
USE NUMBER KEYS NEXT
KTD-405 keypad (Supervisor Programming)
Changing the SEIZE CONTROL time Use the number keys to enter the new time
This is the number of minutes of inactivity before the keypad will exit the seize control mode
Select or to skip over this menu
SEIZE CONTROL TIME: 5
(1-10) MINUTES NEXT
KTD-405 keypad (Supervisor Programming)
Restricting access to presets Use the number keys to enter the new limit
This is the lowest preset number a user may change
Select or to skip over this menu
LOWEST USER PRGMD PRESET
(01-64) 58 NEXT
KTD-405 keypad (Supervisor Programming)
Programming the SOFT keys This feature is not yet implemented
Select -, or to skip over this menu
Pressing + displays the following message:
PROGRAM SOFT KEYS?
<+>=YES <->=NO NEXT
NOT IMPLEMENTED
KTD-405 keypad (Supervisor Programming)
Programming the ACCESS codes This feature is not yet implemented
Select -, or to skip over this menu
Pressing + displays the following message:
CHANGE ACCESS CODES?
<+>=YES <->=NO NEXT
NOT IMPLEMENTED
User Programming
KTD-405 keypad (User Programming)
To Access User Programming: Press and hold the key
The unit will beep and show the following display
User programming password is 5,7,9,
ENTER PROGRAMMING
CODE:
seq
KTD-405 keypad (User Programming)
Changing the Operating Mode Two choices are available:
Digiplex
Zone
Use the joystick or these buttons to select the mode
Select or to skip over this menu
OPERATING MODE: DIGIPLEX
<,>=SELECT NEXT
= , =
KTD-405 keypad (User Programming)
Setting the system size Enter the highest camera number in your system
Select or to skip over this menu
SYSTEM SIZE:
<CAMERAS> 511 NEXT
DigiPlex mode Menus
KTD-405 keypad (User Programming)
Setting the system size Enter the highest monitor number in your system
Select or to skip over this menu
SYSTEM SIZE:
<MONITORS> 64 NEXT
DigiPlex mode Menus
KTD-405 keypad (User Programming)
Setting the system size Enter the highest multiplexer number in your system
Select or to skip over this menu
SYSTEM SIZE:
<MPLXS> 32 NEXT
DigiPlex mode Menus
KTD-405 keypad (User Programming)
Setting the system size Enter the highest VCR number in your system
Select or to skip over this menu
SYSTEM SIZE:
<DSR/VCR> 32 NEXT
DigiPlex mode Menus
KTD-405 keypad (User Programming)
Setting the system size Enter the highest preset number in your system
Select or to skip over this menu
SYSTEM SIZE:
<PRESETS> 63 NEXT
DigiPlex mode Menus
KTD-405 keypad (User Programming)
Restricting system access This menu restricts access to specified cameras
Use the joystick or these buttons to select the camera
Select or to skip over this menu
CAMERA 000 ACCESS? YES
<+>=YES <->=NO NEXT
DigiPlex mode Menus
= , =
KTD-405 keypad (User Programming)
Restricting system access This menu restricts access to specified cameras
Use the joystick or these buttons to select the camera
Select or to skip over this menu
CAMERA 000 ACCESS? YES
<+>=YES <->=NO NEXT
DigiPlex mode Menus
= , =
KTD-405 keypad (User Programming)
Restricting system access This menu restricts access to specified monitors
Use the joystick or these buttons to select the monitor
Select or to skip over this menu
MONITOR 01 ACCESS? YES
<+>=YES <->=NO NEXT
DigiPlex mode Menus
= , =
KTD-405 keypad (User Programming)
Restricting system access This menu restricts access to specified recorder
Use the joystick or these buttons to select the recorder
Select or to skip over this menu
Pressing “+” displays this menu:
Enter a number from 0 to 511, or 0 for NONE or
Select or to skip over this menu
DSR/VCR 01 ACCESS? YES
<+>=YES <->=NO NEXT
DigiPlex mode Menus
VCR 01 MATRIX INPUT:
000 <0=NONE> NEXT
= , =
KTD-405 keypad (User Programming)
Restricting system access This menu restricts access to specified multiplexer
Use the joystick or these buttons to select the multiplexer
Select or to skip over this menu
MPLX 01 ACCESS? YES
<+>=YES <->=NO NEXT
DigiPlex mode Menus
= , =
KTD-405 keypad (User Programming)
If you pressed “+” (yes): The next display will show:
Followed by:
Followed by:
The keypad will advance to the next multiplexer menu automatically
MPLX01 BRAND CBR DVMRe
<,>=SELECT NEXT
MPLX 01 MATRIX INPUT?
000 <0=NONE NEXT
SELECT MAX OUTPUTS: 02
<,>=SELECT NEXT
DigiPlex mode Menus
KTD-405 keypad (User Programming)
Programming the monitor offset Enter a number for the offset needed in your system
Select or to skip over this menu
MONITOR OFFSET
NUMBER: 0 NEXT
DigiPlex mode Menus
KTD-405 keypad (User Programming)
Queuing and announcing call-ins If you select “+” in this display:
You need to select either SINGLE or MULTIPLE tone here:
Also specify a monitor to display the queued calls:
Select or to skip over this menu
ANNUNCIATION? NO
<+>=YES <->=NO NEXT
CALL TONE TYPE? MULTIPLE
<,>=SELECT NEXT
SPOT MONITOR NUMBER: 0
<0=UNASSIGNED> NEXT
DigiPlex mode Menus
KTD-405 keypad (User Programming)
End of menus notification Pressing from the previous menu will cause the
keypad to display this message:
Select or press and hold for 3 seconds to exit the menus
PRESS <SEQ> FOR 3
SECONDS TO EXIT
DigiPlex mode Menus
seq
KTD-405 keypad (User Programming)
Changing the Operating Mode Two choices are available:
DigiPlex
Zone
Use the joystick or these buttons to select the mode
Select or to skip over this menu
OPERATING MODE: ZONE
<,>=SELECT NEXT
= , =
KTD-405 keypad (User Programming)
Programming the Mode label This menu allows you to select one of several labels for
the LCD display during normal operations
Selections Include:
ZONE, MPLX, DVMR, TERR, BLDG
FLR, DEPT, STA, SITE, AREA
Select or to skip over this menu
LCD DISPLAY LABEL: ZONE
<,>=SELECT NEXT
Zone mode Menus
KTD-405 keypad (User Programming)
Programming the zone titles This menu allows you to select a title to display when
the specified zone is being accessed.
Select or to skip over this menu
Enter a two-digit code and the keypad will advance to the following menu automatically
Program the label characters the same way as keypad titles
Select or to skip over this menu
ENTER ZONE ADDRESS: 01
(01-16) NEXT
Zone mode Menus
ZONE 01 TITLE: <>
(01-16) NEXT
KTD-405 keypad (User Programming)
Programming the Zone type This menu allows you to identify the specific device
that makes up a zone:
Selections Include:
CALIBUR MMX, CBR DVMRe, CBR TRIPLEX,
CBR DUPLEX, CBR SIMPLEX, MATRIX SWCH,
Select or to skip over this menu
ZONE 01 HUB: CBR DVMRe
<,>=SELECT NEXT
Zone mode Menus
KTD-405 keypad (User Programming)
Setting the zone size (monitors) This menu restricts access only to available zone monitors
Use the number buttons to set the number of monitors
Select or to skip over this menu
Setting the zone size (cameras) This menu restricts access only to available zone cameras
Choices include 4, 9, 10, 16 and 32
Use the joystick or these buttons to select the mode
Select or to skip over this menu
ZONE 01 MON. OUTPUTS?
01 TO 02 NEXT
Zone mode Menus
ZONE 01 CAM. INPUTS? 16
<,>=SELECT NEXT
= , =
KTD-405 keypad (User Programming)
Programming zone access privileges Program the cameras that this keypad can access:
Program the monitors that this keypad can access:
Program user access to the zone’s recorder :
You should deny access unless you have a Triplex or MMX connected to a VCR using sub-macros.
ZONE 1 CAM 01 ACC? YES
<+>=YES <->=NO NEXT
ZONE 1 MON 01 ACC? YES
<+>=YES <->=NO NEXT
ZONE 1 RECORDER ACC? YES
<+>=YES <->=NO NEXT
Zone mode Menus
KTD-405 keypad (User Programming)
If the Zone type is set to MATRIX SWCH: The zone size and access menus displays are slightly
different
ZONE 02 HUB: MATRIX SWCH
<,>=SELECT NEXT
Zone mode Menus
KTD-405 keypad (User Programming)
Programming zone size Program the first camera input number for this zone:
Program the number of monitors for this zone:
Program the number of camera inputs on this zone:
Choices include 4, 9, 10, 16 and 32
SELECT START INPUT: 032
<,>=SELECT NEXT
ZONE 02 MON. OUTPUTS:
01 TO 16 NEXT
ZONE 02 CAM. INPUTS: 64
<,>=SELECT NEXT
Zone mode Menus
KTD-405 keypad (User Programming)
Programming zone access privileges Program the cameras that this keypad can access:
Program the monitors that this keypad can access:
Program user access to the zone’s recorder :
You should deny access unless you have a Triplex or MMX connected to a VCR using sub-macros.
ZONE 02 CAM 01 ACC? YES
<+>=YES <->=NO NEXT
ZONE 02 MON 01 ACC? YES
<+>=YES <->=NO NEXT
ZONE 02 RECORD ACC? YES
<+>=YES <->=NO NEXT
Zone mode Menus
KTD-405 keypad (User Programming)
Queuing and announcing call-ins If you select “+” in this display:
You need to select either SINGLE or MULTIPLE tone here:
Also specify a monitor to display the queued calls:
Select or to skip over this menu
ANNUNCIATION? NO
<+>=YES <->=NO NEXT
CALL TONE TYPE? MULTIPLE
<,>=SELECT NEXT
SPOT MONITOR NUMBER: 0
<0=UNASSIGNED> NEXT
Zone mode Menus
KTD-405 keypad (User Programming)
End of menus notification Pressing from the previous menu will cause the
keypad to display this message:
Select or press and hold for 3 seconds to exit the menus
PRESS <SEQ> FOR 3
SECONDS TO EXIT
Zone mode Menus
seq
Remote Programming
KTD-405 keypad (Remote Programming)
To Access Remote Programming: Press and hold the key
The unit will beep and show the following display
User programming password is 9,5,1,
Correct password entry will cause the following display:
Each selection generates a different set of menus
ENTER PROGRAMMING
CODE:
1=SWITCHER/MPLX 2=ALARMS
3=CAMERA/RCVR EXIT
seq
KTD-405 keypad (User Programming)
Switcher/Multiplexer Programming Identify the device to be programmed
If you select “1” (440) enter the monitor number to use for programming the switcher
The keypad will display this message
1=440 2=CALIBUR
3=340/348 BACK
ENTER MONITOR NUMBER:
(1-64) BACK
SEE MONITOR FOR MENUS
HOLD SEQ <3 SEC> TO EXIT
Switcher/Mux Menus
KTD-405 keypad (User Programming)
Identify the device to be programmed
If you select “2” (CALIBUR) enter the RS-485 address of the unit to be programmed
The keypad will display this message
1=440 2=CALIBUR
3=340/348 BACK
ENTER CALIBUR ADDRESS:
(1-32) BACK
SEE MONITOR FOR MENUS
HOLD SEQ <3 SEC> TO EXIT
Switcher/Mux Menus
KTD-405 keypad (User Programming)
Identify the device to be programmed
If you select “3” (340/348) enter the monitor number to use for programming the switcher
The keypad will display this message
1=440 2=CALIBUR
3=340/348 BACK
ENTER MONITOR NUMBER:
(1-64) BACK
SEE MONITOR FOR MENUS
HOLD SEQ <3 SEC> TO EXIT
Switcher/Mux Menus
KTD-405 keypad (User Programming)
Alarm Programming The keypad will display this message
SEE MONITOR FOR MENUS
HOLD SEQ <3 SEC> TO EXIT
Alarm Menu
KTD-405 keypad (User Programming)
Camera/Receiver Programming (DigiPlex) Identify the device to be programmed
If you select “1” (CYBERDOME) enter the camera address to be programmed
The keypad will display this message
1=CYBERDOME 2=PTZ
3=AUXILIARY BACK
ENTER CYBERDOME SITE
NUMBER BACK
SEE MONITOR FOR MENUS
HOLD SEQ <3 SEC> TO EXIT
Camera/Receiver Menus
KTD-405 keypad (User Programming)
Camera/Receiver Programming (Zone) Identify the device to be programmed, AND Make
sure you have selected the Zone before you enter programming
If you select “1” (CYBERDOME) enter the camera address to be programmed (address must be within the zone)
The keypad will display this message
1=CYBERDOME 2=PTZ
3=AUXILIARY BACK
ENTER ZONE 1 CAMERA
NUMBER__ BACK
SEE MONITOR FOR MENUS
HOLD SEQ <3 SEC> TO EXIT
Camera/Receiver Menus
KTD-405 keypad (User Programming)
PTZ OR Auxiliary Programming If you select “2” or “3” from this menu
The keypad will display this message
1=CYBERDOME 2=PTZ
3=AUXILIARY BACK
NOT IMPLEMENTED
PTZ/Auxiliary Menus
Standard Operation
KTD-405 keypad (Standard Operation)
CAMERA ---
MONITOR 1
Default display after applying power
DigiPlex mode
Zone Mode
ZONE – ZONE TITLE
CAMERA -- MONITOR -
KTD-405 keypad (Standard Operation)
Accessing System Information: Press and hold the key to display the system
information
The keypad will display
Use or to move between these additional system information displays
KEYPAD ADDRESS: 99
KEYPAD 99 NEXT
VERSION 0.1.07
Dec 20 2001 09:32:44
CAM MN MX RC PS QS MO AT
511 64 32 32 63 58 00 W
mon
KTD-405 keypad (Standard Operation)
Accessing Help displays: Press + to display the Help menu
In the help menus:
Pressing any key displays that key’s function
+ “key” displays that key’s shifted function
The help display will cease display after 10 seconds of inactivity
esc
esc
mon
KTD-405 keypad (Standard Operation)
Selecting a monitor: There are two ways:
Enter the monitor number with any preceding zeroes
Example: 1 (systems with less than 10 cameras)
Example: 01 (systems with more than 9 cameras)
Enter the monitor number, then press
Example: 1 +
CAMERA ---
MONITOR 1
KTD-405 keypad (Standard Operation)
Selecting a camera: There are two ways:
Enter the camera number with any preceding zeroes
Example: 3 (systems with less than 10 cameras)
Example: 03 (systems with less than 100 cameras)
Example: 003 (systems with more than 99 cameras)
Enter the camera number, then press
Example: 3 +
CAMERA ---
MONITOR 1
KTD-405 keypad (Standard Operation)
Controlling a camera: Select the camera to be controlled
Pan, Tilt and Zoom can be controlled by the joystick
Up/Down for Tilt control
Left/Right for Pan control
Twist the joystick for Zoom or use the key
Use the and keys for these functions
CAMERA 003
MONITOR 1
+zoom-
+iris- +focus-
KTD-405 keypad (Standard Operation)
Setting a preset: Position the camera
Press the Store key
Enter the preset number in one of three ways:
Enter the two-digit number (Ex. 05 or 16)
Use the AUX-1, AUX-2, AUX-3 or AUX-4 keys for 58-61
Use and for presets 62 and 63 (left and right Auto-Pan limits. Presets 62 and 63 can not be set by entering the two-digit numbers. On with these two keys and .
aux 1
store
KTD-405 keypad (Standard Operation)Programming a Groups (salvos) and Tours: Requires a RS-485 connection and zone selected
Requires Switcher monitor groups to be previously programmed
Press Store + Sequence
This menu will display:
Enter a number from 1 to 64 calls that group of cameras on the monitors
If you press the Tour key the following menu is displayed:
Enter a number from 1 to 12 TO START that group sequence on the monitors
DigiPlex Mode
ENTER MONITOR GROUP
(1-64)-- OR <TOUR>
store seq
ENTER GROUP SEQUENCE
(1-12)--
tour
KTD-405 keypad (Standard Operation)Controlling a recording device: Requires a KTD-93 interface (RS-422 to RS-232)
Key Function DSR/VCR Function DVMRe
Starts recording Starts recording
Stops record or playback Stops record or playback
Starts playback Starts playback
Pauses playback Pauses playback or live mode
Fast Forward Fast Forward
Fast Reverse (rewind) Fast Reverse (rewind)
Frame advance
Depends on device (DSR/VCR)
Play forward (from reverse play)
Frame advance (in pause mode)
Frame reverse
Depends on device (DSR/VCR)
Play reverse (from forward play)
Frame reverse (in pause mode
n/a 2X digital zoom toggle
n/aActivates play and displays search menu
Digiplex Mode
KTD-405 keypad (Standard Operation)Controlling a recording device: Requires a KTD-93 interface (RS-422 to RS-232)
Key Function DSR/VCR Function DVMRe
Joystick
functions
↻ Twist right = variable rate forward
↺ Twist left = variable rate reverse
In Play or Pause modes:
↻ Twist right = variable rate forward
↺ Twist left = variable rate reverse
Skip forward 2MB (about 15 sec.)
Skip backward 2MB (about 15 sec.)
Fast Forward
Fast Reverse (rewind)
Return to center position resumes pause mode
In 2X Zoom mode:
Tilt up
Tile down
Pan right
Pan left
Digiplex Mode
KTD-405 keypad (Standard Operation)Controlling a multiplexer: Requires RS-485 connection
Key Function Multiplexer Function VCR/DSR
Starts recording Starts recording
Stops record or playback Stops record or playback
Starts playback Starts playback
Pauses playback Pauses playback or live mode
Fast Forward Fast Forward
Fast Reverse (rewind) Fast Reverse (rewind)
Frame advanceFrame advance (in pause mode)
Frame reverseFrame reverse (in pause mode
2X digital zoom toggle n/a
Activates play and displays search menu
n/a
Zone Mode
Multiplexer must support sub-macro VCR interface
KTD-405 keypad (Standard Operation)Controlling a multiplexer: Requires a RS-485 connection
Key Function Multiplexer Function DSR/VCR
Joystick
functions
n/a
In Play or Pause modes:
↻ Twist right = variable rate forward
↺ Twist left = variable rate reverse
In 2X Zoom mode:
Tilt up
Tile down
Pan right
Pan left
Zone Mode
Multiplexer must support sub-macro VCR interface
KTD-405 keypad (Standard Operation)Programming a multiplexer AutoList sequence: Requires a RS-485 connection and zone selected
Press Store
Press Sequence
This menu will display:
Enter the first camera number in the sequence
Wait the desire amount of time you want this camera displayed
Enter the next camera number in the sequence
Wait the desire amount of time you want this camera displayed
Repeat procedure until all cameras have been entered in the sequence
Press to cancel or to exit and save the sequence and exit
Zone Mode
ENTER SEQUENCE CAMERA
CANCEL DONE
store
seq
KTD-405 keypad (Standard Operation)Controlling a recording device: Requires a KTD-93 interface (RS-422 to RS-232)
Key Function DSR/VCR
Starts recording
Stops record or playback
Starts playback
Pauses playback
Fast Forward
Fast Reverse (rewind)
Frame advance
Depends on device (DSR/VCR)
Frame reverse
Depends on device (DSR/VCR)
Joystick↻ Twist right = variable rate forward
↺ Twist left = variable rate reverse
Zone Mode
KTD-405 keypad (Standard Operation)Programming a Calibur™ multiplexer: Requires RS-485 connection
Enter programming via the Remote Programming code 9,5,1,
Select 1 for switcher/multiplexer
Select 2 for Calibur
Enter the Calibur RS-485 address
Press (ENTER)
Enter the Calibur password for the device
Zone Mode
seq
KTD-405 keypad (Standard Operation)Programming a Calibur™ multiplexer: Navigate the Calibur multiplexer menus with these keys:
Key Function
Joystick moves left, right, up, down in menus
Makes selections
Backspaces out of selections or exits programming from the main menu
Move up in menus
Move down in menus
Move right in menus
Move left in menus
Same as
Same as
Zone Mode
esc
KTD-405 keypad (Standard Operation)Keys with special functions: These keys have some special applications:
Key Function
Programmable two ways:
Use with number keys to display mult-image views (if supported)
Used to sequence through multi-display image views (if supported)
OPEN or Preset 58
CLOSE or Preset 59
STOP or Preset 60
TALK or Preset 61
Used for activating tours or Auto-Pan mode
Used to send the selected camera to a preset (if camera is capable)
Clears numerical menu entries (future function clears alarms)
Places selected CyberDome in auto-focus
Addresses remote recording device
view
aux 1
aux 2
aux 3
aux 4
tour
find
dsr/vcr
autofocus
esc
KTD-405 keypad (Standard Operation)Keys with special functions: These keys have not been implemented yet:
Key Function
Alarm key
1st (First) key
alarm
1st
PYTANIA
Recommended