Gate Rubber Seals - · PDF fileGate Rubber Seals PRODEPLASTICOS SAS CARRERA 2 No 30 - 34...

Gate Rubber Seals

PRODEPLASTICOS SAS CARRERA 2 No 30 - 34 ,TELEFONOS: 57 2 3739077 , 57 2 6815724, 301-2976850,

CALI-COLOMBIA, E-mail: prodeplasticos@gmail.com

CONTENTS

1- USEFUL INFORMATION / WARRANTY

2- TECHNICAL ESPECIFICATIONS

3- “J” SEALS

4- CENTER BULB SEALS

5- DOUBLE-BULB SEALS

6- SPECIAL SEALS

7- SIDE SEALS

8- RECTANGULAR SEALS

9- SEALS WITH CHAMFER OR RADIUS

10- CORNER SEALS

11- FRAMES WITH VULCANIZED SPLICES

12- FASTENING WASHERS

13- VALVE SEALS / SHIMS / PADS

14- TECHNICAL BULLETINS

Gate Rubber Seals

Useful information / Warranty

FOR DESIGNERS

FOR PURCHASERS

FOR USERS

WARRANTY

Gate Rubber Seals

Useful information

FOR DESIGNERS

1) Our SBR composite seals feature excellent mechanical

properties, meeting the requirement to withstand ozone attack

and featuring better water absorption characteristics than those

provided by polychloroprene compounds.

The use of polychloroprene specification should be restricted to special

conditions:

a) Regions with high U.V. rays incidence and environments with

high ozone concentration.

b) The effect of environmental aggressive factors, such as certain

chemicals, not usually occurring in clean river waters (chemicals

for instances).

2) In some cases, not even SBR or CR will be adequate to the

environment where gates are installed (for instance, radiations

or an acid medium). Our technicians will indicate the proper

elastomer for each specific case.

3) Depending on project requirements, seal hardness properties

other than 50/60 Shore A and 60/70 Shore A hardness may be

required above or below standardized values.

Gate Rubber Seals

4) Refer to catalog and try to adapt your requirements to one of the

existing profiles.

In the event of minor changes having to be introduced in a given shape,

please contact our technicians.

This is highly recommended as tooling, in addition to high production

costs will demand a long manufacturing period.

5) Check that the selected shape is provided with the

corresponding corner (not all of them are).

6) Assess the need for using corner seals, or whether they could

be replaced with vulcanized splices at 45º.

7) Please refer to us regarding seals coated with a PTFE film, as

not all shapes in our catalog could be coated.

8) Pleases contact our technicians to request the development and

testing of non-existing shapes (see our bulletins).

9) Our seals are manufactured by the continuous molding process

and, therefore, will feature excellent mechanical and

dimensional characteristics, with minimum variations and with

smooth surfaces. Additionally, this process enables PTFE

coatings to be applied.

Gate Rubber Seals

Technical Specifications

Typical Specifications for SBR and CR Elastomers

Typical PTFE Fil Specifications

Gate Rubber Seals

FOR PURCHASERS

Our seals are made to order only and, therefore, please make sure your

orders will be placed with due advance notice to avoid delaying your

projects.

In order to expedite our reply to your quotation, please mention the

code number part or the dimensions of your selected shape, the type of

rubber (SBR, CR, or others), the required hardness (50/60, 60/70, or

others) and the span size.

Seals are always supplied with some excess length to enable them to

be adapted during assembly.

FOR USERS

1) Upon delivery of our seals to your premises, you will have to

remove them from their packaging and have them stored in a

sheltered place, away from direct sunlight, heat and moisture.

Ideally, our seals should be spread out for storage but, should

this not be possible, make sure the bending radius will be as

large as possible less coiling during storage. Nothing should be

piled on top of our seals.

2) PTFE-coated seals should be carefully handled, never bending

them over in the direction of coating as this will lead to film

wrinkling or peeling. (see handling instructions).

Gate Rubber Seals

3) The use of our metal/rubber washers is recommended,

particularly whem installing sluice gate seals.

4) Our technicians will be available to assist you from the design

stage up to the maintenance of your sluice gates. If so

requested, we will be pleased to visit the power station to

provide on-site assistance and to help solving possible

problems.

WARRANTY

Our sponsor was awarded ISO 9001:2000 certification by Bureau

Veritas.

Our seals are delivered together with a certificate of the tests performed

on the composite used.

Provided adequate conditions of transportation, handling and storage

are complied with, we will guarantee our seals for a period of 3 years

counted from the date they are shipped from our facilities.

Gate Rubber Seals

Typical Specifications for SBR and CR Elastomers

Original properties:

Durometer Hardness – Shore A (ASTM

D 2240), Points

SBR CR

50/60 60/70 50/60 60/70

Tensile Strength (ASTM D 412), MPa

(min.) 16.5 20.6 14.0 18.5

Ultimate Elongation (ASMT D 412), %

(min.) 450 450 450 450

Compression set: (ASTM D 395-B) (22

h/70º C)

Residual Distortion, % (max.)

30% 30% 30% 30%

Accelerated aging in air oven (ASTM

D 573) (70 h/70º C)

Durometer Hardness – Shore A

Variation, Points (max.)

± ± ± ±

Ultimate Tensile Strength Variation, %

(max.) -20 -20 -20 -20

Water resistance: (ASTM D 471) (70

h/70º C)

Weight Variation, % (max.)

+5 +5 +10 +10

Ozone resistance: (ASTM D 1171) (72

h / 40º C / 50 mPa)

Surface Conditions

cracking

Notes:

1. Test according to ASTM (American Society for Testing

and Materials) standards.

Gate Rubber Seals

2. For seals not meeting the afore mentioned standard (e.g.,

other hardness ranges, other types of elastomers, etc.)

please refer to our Technical Dept. for a new specification

to be established.

Typical PTFE Film Specifications

Description

PTFE film with 15% of fiber glass, thickness 0,8 or 1,5 mm and green

color.

TEST VALUE METHOD

Tensile Strength (min.)

Ultimate Elogation (min.)

13.7 MPa / 2000 psi

ASTM D 638

Typical specifications for rubber / PTFE

composite:

- To be carried out acoording to

ASTM D-413 standard

- Load of 13,5 kgf per 25 mm cating

- Tensile test machine at 300

mm/min

PTFE bond strength test (on test

plece:

- To be carried out according to

ASTM D 413 standard

- Separating of 25 mm film

- Minimum separating load: 13,5

External Aspect

Seals shall present uniform surfaces, free from defects capable of

jeopardizing the sealing function.

Gate Rubber Seals

Splices shall be flawless, with a slight unlevelness being however

admissible between joined shapes, due to joint rubber contraction.

Tolerance / Dimensional Check

Tolerances in the cross section dimensions of section shapes and seal

frame front end shall comply with ISO 3302, Class M3 (that superseded

DIN 7715, Part 2, Class M3 standard).

The PTFE film shall present in the splice area a spacing to each other

from 3 to 10 min; in that region, the film could show a slight unlevelness

relative to the section shape surface.

Customers are advised to refer to PRODEPLASTICOS for the

maximum unlevelness values in splices and joined section shapes.

Gate Rubber Seals

“J” Seals

P - 01

P - 01-1

P – 01 - 2

P - 02

P - 04

P – 04 - 1

P – 18

Gate Rubber Seals

P - 18

P-18 L H R E R1

A 156,5 67 33 20 8

Gate Rubber Seals

“J” Seals

P – 02 CHAMFERED “J” SEAL

P-02 L D E R C

b 130 40 20 40 10x45º

c 126 40 20 40 10x45º

SPECIAL “J” SEALS

P – 04

P-04 L L1 L2 H H1 H2 D E R R R1 R2

a 190 60 30 70 40 30 20 20 3 5 5 7º

Gate Rubber Seals

P – 04 - 1

P-04-1 L L1 L2 H H1 H2 D E R R1

a 150 60 30 60 30 30 20 20 5 5

B 97 45 22.5 42 21 21 20 15 0 0

C 82 35 17.5 38 19 19 15 14 0 0

P – 01 “J” SEAL

P-01 L D E R P-01 L D E R

a 127 45 15 5 l 85 30 13 10

a1 110 45 15 5 m 85 30 12 4

a2 107.5 45 15 5 n 45 20 7 6

a3 120 45 15 10 o 110 40 20 7.5

a4 58.5 23 7.5 5 p 152 70 25 8

a5 110 40 10 7.5 q 130 45 15 10

b 110 40 20 40 r 127 40 20 40

b1 95 40 20 40 s 100 45 15 8

c 105 50 18 10 t 35 16 3 3

d 102 45 14 7 v 150 60 20 6

e 100 45 15 10 x 175 45 18 5

e1 95 45 15 10 x1 122.5 45 18 5

f 110 45 18 7.5 y 126 40 20 32

Gate Rubber Seals

f1 1000 45 18 7.5 w 102 44 15 5

g 78 35 12 5 z 90 40 14 8

h 60 27 8 2 z1 86 40 12 8

i 130 50 20 10 z2 135 65 22 7

j 130 40 20 40 z3 120 45 22 7

k 115 50 15 5 (mm)

P-01-1 “J” SEAL – HOLLOW BULB

P-01-1 L D E R D1 P-01-1 L D E R D1

a 127 45 15 5 25 j 130 40 20 40 25

a1 138 60 20 6 28 k 115 50 15 5 20

d 102 45 14 7 15 p 152 70 25 8 28

e 100 45 15 10 19 q 130 45 15 10 25

g 78 35 12 5 15 w 102 44 15 5 22

i 130 50 20 10 20 z 90 40 14 5 15

(mm) (mm)

Gate Rubber Seals

P-01-2 “J” SEAL WITH SHIMS

P-01-2 L L1 D E E1 R

a 60 30 27 18 8 2

d 102 51 45 16 14 6

z 90 42 40 16 14 8

Gate Rubber Seals

Double-Bulb Seals

P – 29

P – 29 – 1

P – 29 – 2

P – 29 – 3

Gate Rubber Seals

P-29 L D D1 E R R1

a 115 35 35 10 3 3

b 170 40 40 18 5 5

c 150 45 45 15 5 5

d 168 48 48 15 5 5

e 154 45 43 14 7.5 8.5

P-29-1

P-29-1 L L1 D E R

a 215 105 45 15 5

Gate Rubber Seals

P-29-2

P-29-2 L L1 D E R

a 280 120 48 15 5

P-29-3

P-29-3 L L1 L2 D D1 E E1 R R1 C

a 211.5 110 11 43 45 19 14 7.5 8.5 2.5X45º

Gate Rubber Seals

Center Bulb Seals

P – 08

P – 08 – 1

Gate Rubber Seals

P-08 L D E R

a 160 45 15 7

d 160 50 18 7.5

e 120 35 12 8

f 160 51 20 7.5

g 175 45 18 8

h 170 45 18 8

i 158 43 14.3 8

j 93 27 8 2

k 196 44 14 8

P-08-1

P-08-1 L L1 L2 D D1 E E1 R R1

a 158 6 42.5 14 17 14 22 10 1.5x45º

Gate Rubber Seals

Side Seals

P - 03

P – 03 - 1

P – 17

P – 20

P – 21

P – 22

P – 28

P – 66

Gate Rubber Seals

P-03 L L1 L2 L3 E H H1 H2 R R1 R2 R3

a 78 64 19 10 15 80 40 40 15 13 5 4

R4 A A1 A2 A3

5 13º 7º 7º 9º

P-03-1

P-03 L L1 L2 L3 E H H1 H2 R R1 R2 A

a 86 70 16 18 16 81 37 44 4 1.5 10 10º

Gate Rubber Seals

P-17 L L1 E E1 E2 R R1 A A1

a 75 70 16 16 5 8 24 60º 45º

b 98.5 100 22 23 13 25 40 60º 15º

P-20 L D E H A

a 87.5 25 15 45 40º

Gate Rubber Seals

P-21 L L1 E R A

a 30.0 115 7.5 7.5 15º

P-22 L L1 E A

a 30.0 115 7.5 15º

Gate Rubber Seals

P-28 L L1 L2 E E1 H H1 R E1 R2

a 100 66 58 20 27 75 14 7 26 7

b 100 66 56 22 28.5 75 14 7 26 7

c 120 80 72 22 27 75 14 7 26 7

d 140 96 85 22 28 76 14 3 25 7

R3 R4 A

7 12 15º

6 13.5 15º

7 12 15º

7 13 15º

Gate Rubber Seals

P-66 L L1 L2 D E R R1 R2 A H

a 100 50 60 25 18 2 15 15 60º 55

b 120 70 80 25 18 2 15 15 60º 55

Gate Rubber Seals

TECHNICAL BULLETINS

The following technical bulletins will be mailed upon request to our

sales sector. Should you be interested, please register to receive future

bulletins.

1- DEFLECTION: “J” TYPE SEAL – R-01 s.

2- SEAL EXPOSURE TO INCLIMENT WEATHER.

3- TECHNICAL SPECIFICATION FOR RUBBER PRODUCTS.

4- GATE SEALS TOLERANCES.

5- UNLEVEL CONTROL ON GATES SEALS.

6- GATE SEALS CLADDING WITH PTFE.

7- COMPARISON: EXTRUDED X MOLDED SEALS.

8- DEFLECTION: “J” TYPE SEAL – R-01 s WITH RUBBER

SHIMS.

9- R-14 a COMPRESSION.

10- DURABILITY OF SBR SEALS.

11- USEFUL LIFE OF PTFE CLAD SEALS.

12- SEALS HANDLING, TRANSPORT AND STORAGE.

13- METAL-RUBBER WASHERS FOR SEAL FIXING.

Gate Rubber Seals

Technical Bulletins

TECHNICAL BULLETINS

Gate Rubber Seals

Gate Rubber Seals - · PDF fileGate Rubber Seals PRODEPLASTICOS SAS CARRERA 2 No 30 - 34...

Documents

Exactseal rubber-manufacture-rubber-gaskets-orings-and-rubber-seals-products-company-in-united-states

RUBBER BODY SEALS AND GASKETS - zeni.netcod.zeni.net/trf/TR2-TR3GB/pdf/T23GB-Seals.pdf · 2019. 5. 2. · RUBBER SEALS, fitted to short door models, 1955-63 650046 Rubber Seal, door,

E shaped extruded silicone rubber seals and gaskets

Seven Seals 1-57

SILICONE EXTRUSIONS EPDM EXTRUSIONS RUBBER STRIPS & SEALS

IS 15466 (2004): Rubber seals for hydraulic gates

Custom Molded Rubber Radial Shaft Seals Rubber-to-Metal … · 2017-10-14 · Gaskets Mechanical Seals Hydraulic Seals Machined Plastics Radial Shaft Seals Rubber-to-Metal Bonded

Malaysian Rubber Export Promotion Council (MREPC) · Mumbai - 400 021 , Maharashtra, India Tel: +91 22 6221 6725 ... rubber gaskets, rubber seals, rubber foots, rubber finger and

Rubber & Plastic Machining - Hi-Tech Seals · 2020. 3. 4. · Rubber & Plastic Machining Rubber & Plastic Machining Hi-Tech Seals' machining facilities are located in Edmonton, AB

O-Rings Custom Molded Rubber Gaskets Mechanical Seals

Rubber Hydraulic Seals & Waterstops - Trelleborg Australiatrelleborg.com.au/.../12/9765-Rubber-Hydraulic-Seals-a… · · 2017-09-11and manufacturing Australia’s widest range

GOODWAY RUBBER - bonded, hydraulic, shaft sealgoodwayrubber.kong.tw/catalog.pdf · Procucts include shaft seals, hub seals. oil seals and full range of bonded seals. 2002 Establishment

Rubber Hydraulic Seals & Waterstops - Trelleborg/media/engineered... · Rubber Hydraulic Seals & Waterstops. 1 ... Trelleborg Seals are moulded, or extruded, ... Trelleborg Dam Gate

Rubber Mouldings Plastic Mouldings Seals O Rings Rubber to Metal

MacrOringT” Seals from Apple Rubber

Custom Molded Rubber Radial Shaft Seals Rubber-to-Metal ...O-Rings Custom Molded Rubber Gaskets Mechanical Seals Hydraulic Seals Machined Plastics Radial Shaft Seals Rubber-to-Metal

ERIKS - Oilseals seals... · · 2015-08-07Oil Seals of rubber/textile construction for heavy duty applications Oil Seals in non standard rubber compounds such as ... This is generally

Bonded Seals - Fridle Seals - Fridle.pdf · Steel and rubber bonded seals are highly resistant, thanks to the coupling of metal and rubber. These seals are made of a synthetic rubber

The perfect ˜t for rubber solutions - Philippe Jans · INFLATABLE SEALS PRODUCT INFORMATION RUBBERFLATE® INFLATABLE SEALS PRODUCT INFORMATION The perfect ˜t for rubber solutions

RUBBER SEALS FOR