View
3
Download
0
Category
Preview:
Citation preview
COLUMBIA WHITE OIL 8
COLUMBIA WHITE OIL 12
Note:
1. The above data is indicated of recent average values only. Minor variations which do not affect product performance or quality may be
expected in manufacture.
2. Specific requirements shall be custom-made on request.
3. White Oils are manufactured in compliance with I.P., U.S.P., B.P. and E.Ph specifications and conform to the requirement of U.S. FDA 21
CFR 172.878 (a) and (b).
SR. NO
TESTS METHOD RANGE TYPICAL VALUES
COLUMBIAPETROCHEM
WHITE OILS
SR. TESTS METHOD RANGE TYPICAL VALUES
NO
1. Description Visual Transparent colourless oily
liquid
Transparent colourless oily
liquid
2. Colour ASTM D 156 +30 +30
3. Density @ 25 ºC, g/ml
@ 29.5 ºC, g/ml
ASTM D 1298 0.812 - 0.845
0.810 - 0.842
0.819
0.816
4. Kinematic Viscosity
@ 40 ºC
ASTM D 445 7 - 10 cSt 8.5 cSt
5. Refractive Index @ 20 ºC ASTM D 1218 – 1.476
6. Sulphur Compound IS:7299/I.P. Passes Passes
8. Flash Point ºC ASTM D 92 150 MIN 154
7. Pour Point ºC ASTM D 97 -6 MAX -39
liquid
1. Description Visual Transparent colourless oily Transparent colourless oily
liquid
2. Colour ASTM D 156 +30 +30
4.
–
3. Density @ 25 ºC, g/ml
@ 29.5 ºC, g/ml
ASTM D 1298 0.818 - 0.858
0.815 - 0.855
0.824
0.821
5.
Kinematic Viscosity
@ 40 ºC
ASTM D 445 10 - 14 cSt 12.9 cSt
Refractive Index @ 20 ºC ASTM D 1218 1.476
7.
8.
6. Sulphur Compound IS:7299/I.P. Passes Passes
Pour Point ºC ASTM D 97 -6 MAX -24
Flash Point ºC ASTM D 92 160 MIN 166
COLUMBIA WHITE OIL 15
COLUMBIA WHITE OIL 20
SR. NO
TESTS METHOD RANGE TYPICAL VALUES
SR. NO
TESTS METHOD RANGE TYPICAL VALUES
1. Description Visual Transparent colourless oily
liquid
Transparent colourless oily
liquid
2. Colour ASTM D 156 +30 +30
3. Density @ 25 ºC, g/ml
@ 29.5 ºC, g/ml
ASTM D 1298 0.823 - 0.863
0.820 - 0.860
0.838
0.835
4.
ºC
Kinematic Viscosity
@ 40
ASTM D 445 14 - 18 cSt 15.5 cSt
5. Refractive Index @ 20ºC ASTM D 1218 – 1.4764
6. Sulphur Compound IS:7299/I.P. Passes Passes
8. ºCFlash Point ASTM D 92 165 MIN 174
7. Pour Point ºC ASTM D 97 -6 MAX -24
liquid
1. Description Visual Transparent colourless oily Transparent colourless oily
liquid
2. Colour ASTM D 156 +30 +30
4.
–
3. Density @ 25 ºC, g/ml
@ 29.5 ºC, g/ml
ASTM D 1298 0.826 - 0.863
0.821 - 0.860
0.830
0.827
5.
Kinematic Viscosity
@ 40 ºC
ASTM D 445 19 - 22 cSt 20 cSt
Refractive Index @ 20ºC ASTM D 1218 1.4765
7.
8.
6. Sulphur Compound IS:7299/I.P. Passes Passes
Pour Point ºC ASTM D 97 -6 MAX -15
Flash Point ºC ASTM D 92 180 MIN 186
COLUMBIAPETROCHEM
WHITE OILS
Note:
1. The above data is indicated of recent average values only. Minor variations which do not affect product performance or quality may be
expected in manufacture.
2. Specific requirements shall be custom-made on request.
3. White Oils are manufactured in compliance with I.P., U.S.P., B.P. and E.Ph specifications and conform to the requirement of U.S. FDA 21
CFR 172.878 (a) and (b).
COLUMBIA WHITE OIL 32
COLUMBIA WHITE OIL 50
SR. NO
TESTS METHOD RANGE TYPICAL VALUES
1. Description Visual Transparent colourless oily
liquid
Transparent colourless oily
liquid
2. Colour ASTM D 156 +30 +30
3. Density @ 25 ºC, g/ml
@ 29.5 ºC, g/ml
ASTM D 1298 0.828 – 0.868
0.825 – 0.865
0.850
0.847
4. Kinematic Viscosity
@ 40 ºC
ASTM D 445 30 – 33 cSt 32 cSt
5. Refractive Index @ 20ºC ASTM D 1218 - 1.4765
6. Sulphur Compound IS:7299/I.P. Passes Passes
7. Pour Point ºC ASTM D 97 - 6 MAX -18
8. Flash Point ºC ASTM D 92 200 MIN 210
SR. NO
TESTS METHOD RANGE TYPICAL VALUES
1. Description Visual Transparent colourless oily
liquid
Transparent colourless oily
liquid
2. Colour ASTM D 156 +30 +30
3. Density @ 25 ºC,g/ml
@ 29.5 ºC, g/ml
ASTM D 1298 0.828 – 0.873
0.825 – 0.870
0.838
0.835
4. Kinematic Viscosity
@ 40 ºC
ASTM D 445 48 - 54 cSt 49 cSt
6.
–5. Refractive Index @ 20ºC ASTM D 1218 1.477
Sulphur Compound IS:7299/I.P. Passes Passes
7. Pour Point ºC ASTM D 97 -6 MAX -18
8. Flash Point ºC ASTM D 92 220 MIN 240
COLUMBIAPETROCHEM
WHITE OILS
Note:
1. The above data is indicated of recent average values only. Minor variations which do not affect product performance or quality may be
expected in manufacture.
2. Specific requirements shall be custom-made on request.
3. White Oils are manufactured in compliance with I.P., U.S.P., B.P. and E.Ph specifications and conform to the requirement of U.S. FDA 21
CFR 172.878 (a) and (b).
COLUMBIA WHITE OIL 100
COLUMBIA WHITE OIL 68SR. NO
TESTS METHOD RANGE TYPICAL VALUES
1. Description Visual Transparent colourless oily
liquid
Transparent colourless oily
liquid
2. Colour ASTM D 156 +30 +30
3. Density @ 25 ºC, g/ml
@ 29.5 ºC, g/ml
ASTM D 1298 0.848 - 0.880
0.845 - 0.880
0.856
0.853
4.
ºC
Kinematic Viscosity
@ 40
ASTM D 445 65 - 75 cSt 70 cSt
5. Refractive Index @ 20ºC ASTM D 1218 — 1.4775
6. Sulphur Compound IS:7299/I.P. Passes Passes
8. ºCFlash Point ASTM D 92 220 246
7. Pour Point ºC ASTM D 97 -6 MAX -15
SR. NO
TESTS METHOD RANGE TYPICAL VALUES
liquid
1. Description Visual Transparent colourless oily Transparent colourless oily
liquid
2. Colour ASTM D 156 +30 +30
4.
–
3. Density @ 25 ºC, g/ml
@ 29.5 ºC, g/ml
ASTM D 1298 0.853 - 0.880
0.850 - 0.880
0.857
0.854
5.
Kinematic Viscosity
@ 40 ºC
ASTM D 445 95 - 105 cSt 100 cSt
Refractive Index @ 20ºC ASTM D 1218 1.4775
7.
8.
6. Sulphur Compound IS:7299/I.P. Passes Passes
Pour Point ºC ASTM D 97 -6 MAX -12
Flash Point ºC ASTM D 92 240 248
COLUMBIAPETROCHEM
WHITE OILS
Note:
1. The above data is indicated of recent average values only. Minor variations which do not affect product performance or quality may be
expected in manufacture.
2. Specific requirements shall be custom-made on request.
3. White Oils are manufactured in compliance with I.P., U.S.P., B.P. and E.Ph specifications and conform to the requirement of U.S. FDA 21
CFR 172.878 (a) and (b).
WHITE OIL LIGHT
WHITE OIL HEAVY
SR. NO
TESTS TYPICAL VALUES
1. Description Transparent Oily Liquid
2. Solubility Insoluble in water & alcohol, soluble inether and chloroform
3. Density @ 25 ºC, g/ml 0.810 to 0.860
4. Kinematic Viscosity @ 40ºC
5. Cloud Point ºC
6. Pour Point ºC
7. Flash Point ºC
7 cSt to 40 cSt
Below zero
- 9 MAX
150 MIN
SR. NO
TESTS TYPICAL VALUES
1. Description Transparent Oily Liquid
2. Solubility Insoluble in water & alcohol, soluble inether and chloroform
3. Density @ 25 ºC, g/ml 0.845 to 0.880
4. Kinematic Viscosity @ 40ºC
5. Cloud Point ºC
6. Pour Point ºC
7. Flash Point ºC
40 cSt to 120 cSt
Below zero
-9 MAX
180 MIN
REPORT
1. The sample complies with the prescribed standards of quality.
2. The methods used were ASTM.
COLUMBIAPETROCHEM
WHITE OILS
NOTE:
1) All oils above are colourless (Saybolt +30 Colour), odourless, tasteless and meet requirements of U.S. FDA and USP, B.P. and Eph Pharmacpeia standard for Neutrality, Sulphur Compounds,
Solid Paraffins and Carbonizable substances. All the above oils have nil arsenic and lead content.
2) The above data is indicated of recent average values only. Minor variations which do not affect product performance or quality may be expected in manufacture.
3) Specific requirements can be custom-made on request.
ISO 9001-2008 CERTIFIED ISO 14001-2004 CERTIFIED
VISCOSITY GRADE TESTS METHOD 8 12 15 20 32 50 68 100
Density Range
Typical@ 29.5 ºC, g/mlASTM D 1298
0.810-0.842
0.816
0.815-0.855
0.8210.820-0.860
0.835
0.826-0.863 0.825-0.8650.847
0.825-0.870
0.835
0.845-0.880
0.853
0.850-0.880
0.854
ASTM D 445 8.5 12.9 15.5 20 32 49 70 100
Refractive Index @ 20 ºC ASTM D 1218 1.476 1.476 1.4764 1.4765 1.4765 1.477 1.4775 1.4775
Cloud Point ºC ASTM D 97 -12 -9 -9 -9 -6 -6 -6 -6
Pour Point ºC ASTM D 97 -39 -24 -24 -15 -18 -18 -15 -12
Flash Point ºC ASTM D 92 154 -166 174 186 210 240 246 248
Colour ASTM D 156 +30 +30 +30 +30 +30 +30 +30 +30
Kinematic Viscosity, SUS at 100 ºF ASTM D 2161 56 72 85 104 152 245 340 500
Kinematic Viscosity, cSt at 40 ºC
COLUMBIAPETROCHEM
WHITE OILS
0.827
TYPICAL TEST RESULTS
CHARACTERISTICS TEST METHOD
AS PER IS:335 AS AMENDED
Appearance
Density @ 29.5 ºC
Kinematic Viscosity at 27 ºC , cSt
Interfacial Tension N/m @27ºC
Flash Point PMCC ºC
Pour Point ºC
Neutralisation valuea) Total Acidity, mg KOH/gm (Max)b) Inorganic acidity/alkalinity
Corrosive Sulphur
Electrical Strength (Breakdown Voltage) KV(rms)
a) New Unfiltered Oil
Presence of oxidation inhibitor % wt
Water Content ppm Max
S.K.Value, % (Max)
Accelerated Ageing test 96 hrs @ 115 ºC(open Beaker Method)
b) After Filteration
a) Sp. Resistance (Resistivity) ohm-cm @ 27 ºC
b) Sp. Resistance (Resistivity) ohm-cm @ 90 ºC
c) Dielectric Dissipation Factor @ 90 ºC
d) Total Acidity, mg/KOH/gm
e) Total sludge value, % Wt
Dielectric Dissipation factor,(Tan Delta) at 90 ºC
Specific Resistance (Resisitivity) Ohm-cma) At 90 ºCb) At 27 ºC
Oxidation Stability 164 Hours @ 100 ºCa) Neutralisation Value after Oxidationb) Total Sludge
A representative sample of theoil shall be examined in 100 mm thick layer at 27 ºC
IS : 1448 (P-16)
IS : 1448 (P-25)
IS : 6104
IS : 1448 (P-21)
IS : 1448 (P-10)
IS : 1448 (P-2)
Annex B
IS 6792 30 -
60
-
-
-
-
0.400.10
0.0910.0087
0.002
IS : 13631
IS : 13567
Annex D, IS : 335
--
--
Annex C
IS : 12177
IS : 6103
IS : 6103
IS : 6262
IS : 1448 (P-2)
IS : 6262
IS : 6103
--
0.03Nil
Non Corrosive
The oil shall not contain antioxidant additives
8 Max
-
-
-
-
-
- 50 ppm
2.5 X 10¹²
0.2 X 10¹²
0.20
0.05
0.05
35 x 10¹²1500 X 10¹²
300 x 10¹²13200 X 10¹²
0.840 g/cm³
12.4 cSt
0.048 N/m
160 ºC
-15 ºC
0.0009 mg KOH/gNil
Non Corrosive
68
Not present
15 ppm
1
61.41 X 10¹²
6.87 X 10¹²
0.034
0.035
0.006
72
0.0003
Transparent, clear and light
The oil shall be clear andtransparent & free fromsuspended matter or sediment
COLUMBIA NEW INSULATING OIL
-
-
0.04
140
-
0.89
27
-
-
-6
MIN MAX
Our product conforms to IS 335 : 1993
Note:1. The above data is indicated of recent average values only. Minor variations which do not affect product performance or quality may be expected in manufacture.
2. Specific requirements shall be custom-made on request.
TRANSFORMER OILS COLUMBIAPETROCHEM
Annex. A of IS 12177
NEW INSULATING OIL / TRANSFORMER OIL
TEST DESCRIPTION TEST METHOD SPECIFICATION LIMITS
Appearance
Colour
Kinematic Viscosity, mm /S (max)²
At 40ºC
At -30ºC
Flash Point ºC,(Min), PMCC
Pour Point ºC
Density kg/dm³, @ 20ºC (Max)
Neutralisation Value mg KOH/g (Max)
Interfacial Tension @ 25ºC
Corrosive Sulphur
Total PCB content mg/Kg
Total Furans mg/Kg, Max
Polycyclic Aromatics % mass, Max
Break down Voltage, Min
As Delivered (Kv), min
After Treatment (Kv), min
Dielectric Dissipation factor at 90 ºC and 40 to 60 Hz (Max)
Gassing tendency at 50 Hz after 120 min,mm³/min Method A (Max)
Water Content, Max mg/kg
a) Bulk
b) Drum
Anti - oxidant Additives (Sub Clause 2.5)
Oxidation Stability, 164 hTotal acidity, mg KOH/g of oil (Max)Sludge, % by mass (Max) DDF @ 90 ºC
BS 148-1998
ASTM D 1500
ISO 3104
ISO 3104
ISO 2719
ISO 3016
BS EN ISO 3675
IEC - 62021
ISO - 6295
DIN 51353/BS 5680
IEC 61619
BS EN 61698
BS 2000
IEC 60156
-
-
IEC - 60247/61620
BS 5797/IEC-60628-A
IEC 60814
-
-
IEC 60666/BS 5984
IEC 61125 : 1993(Method C) IEC - 60247
L 0.5
11
1800
130
≤ - 45
0.895
0.01
0.04 Max
Non corrosive
Non detectable
1.00
3.00
30
70
0.005
+5
-
20
30
Not detectable Not detectable
1.20.80.5
0.5
9.0
298
-45
150
0.88
Nil
0.045
Non corrosive
Non detectable
Nil
0.5
50
70
0.0005
+1
-
14
22
1.00.680.36
Transparent, clear, bright,odourless liquid free fromsuspended impurities
Transparent, clear, bright,odourless liquid free fromsuspended impurities
TYPICAL VALUES
New Insulating Oil is a premium grade uninhibited Mineral Insulating Oil for Transformers and Switchgears
TRANSFORMER OILS COLUMBIAPETROCHEM
Our product conforms to IEC 60296:2003/BS-148:1998
Note:1. The above data is indicated of recent average values only. Minor variations which do not affect product performance or quality may be expected in manufacture.
2. Specific requirements shall be custom-made on request.
1. PHYSICAL1.1 Appearance - IEC : 296 Clear, transparent Clear, transparent &
& free from sediment free from sediment & suspended matter & suspended matter
1.2 Density @ 20 ºC g/cm³ ISO : 3675 0.895 Max 0.8221.3 Kinematic Viscosity, Max Cst. ISO : 3104 16.5.0 at 40 ºC 7.6
800 at -15 ºC 4001.4 Interfacial Tension, at 25 ºC N/m ISO : 6295 0.04 Min 0.0521.5 Flash Point ºC ISO : 733 140 Min 1601.6 Water Content Bulk Mg/Kg IEC : 60814 30 Max 9.2
Water Content Drum 40 Max 11.01.7 Pour Point ºC ISO : 3016 -30 Max -36
2. ELECTRICAL2.1 Electrical Strength BDV kVrms IEC : 60156
As Delivered 30 min 62After treatment 50 min -
2.2 Dielectric Dissipation factor - IEC : 60247 0.005 0.0003(tan delta) at 50Hz, Max
3. CHEMICAL3.1 Neutralization Value (Total Acidity) Mg.KOH/gm IEC : 296 0.03 Max 0.0023.2 Corrosive Sulphur - ISO : 5662 Non-Corrosive Non-Corrosive 3.3 Oxidation Stability for 164
hrs at 100 ºC - IEC : 611253.3.1 Neutralization value Mg.KOH/gm - 0.4 Max 0.073.3.2 Total Sludge by mass % - 0.1 Max 0.001
3.6 Presence of Oxidation Inhibitor - IEC : 666 Not detectable Not detected
SR. NO
DESCRIPTION OF TEST UNITTEST METHODAS PER IEC-296
REQUIREDVALUE
MEASUREDVALUE
SR. NO
DESCRIPTION OF TEST UNITTEST METHODAS PER IEC-296
REQUIREDVALUE
MEASUREDVALUE
REMARKS: Conforms to IEC-296/1982, Class - I (UNINHIBITED OIL)
REMARKS: Conforms to IEC-296/1982, Class - II (UNINHIBITED OIL)
TRANSFORMER OILS COLUMBIAPETROCHEM
1. PHYSICAL1.1 Appearance - IEC : 296 Clear, transparent Clear, transparent &
& free from sediment free from sediment & suspended matter & suspended matter
1.2 Density @ 20 ºC g/cm³ ISO : 3675 0.895 Max 0.8701.3 Kinematic Viscosity, Max Cst. ISO : 3104 11.0 at 40 ºC 8.0
1800 at -30 ºC 9001.4 Interfacial Tension, at 25 ºC N/m ISO : 6295 0.04 Min 0.0501.5 Flash Point ºC ISO : 2719 130 Min 1481.6 Water Content Bulk Mg/Kg IEC : 60814 30 Max 8.1
Water Content Drum 40 Max 10.01.7 Pour Point ºC ISO : 3016 -45 Max -45
2. ELECTRICAL2.1 Electrical Strength BDV kVrms IEC : 60156
As Delivered 30 min 60After treatment 50 min -
2.2 Dielectric Dissipation factor - IEC : 60247 0.005 at 90 ºC 0.0002(tan delta) at 50Hz, Max
3. CHEMICAL3.1 Neutralization Value (Total Acidity) Mg.KOH/gm IEC : 296 0.03 Max 0.0033.2 Corrosive Sulphur - ISO : 5662 Non-Corrosive Non-Corrosive 3.3 Oxidation Stability for 164
hrs at 100 ºC - IEC : 611253.3.1 Neutralization value Mg.KOH/gm - 0.4 Max 0.083.3.2 Total Sludge by mass % - 0.1 Max 0.002
3.6 Presence of Oxidation Inhibitor - IEC : 666 Not detectable Not detected
DESCRIPTION
Columbia's Light Liquid Paraffin/White Mineral Oil is suitable for Pharmaceutical, Cosmetics & Food industries for
direct & indirect food contact.
PROPERTIES
For specific uses these oils must be
● Colourless Odourless Tasteless Conforming to the standards of pharmaceutical purity I.P., B.P. & U.S.P. ● ● ●
● Conforming to the standards of oils in contact with edible substances
They are therefore, subjected to a higher refinement so as to be able to conform to particular specifications,
(different specifications) in different countries and the standard FDA (Food & Drugs Administrative U.S.A.)
The range of Columbia Liquid Paraffins has the following gradations:
● ● Light grade Heavy Grade
APPLICATIONS
Chemical Industry
● ● The inert oils for the fabrications of metallic hydrides and catalysts Absorbent oils (e.g. in the extraction of the
natural essence of perfumeries, the impregnated paper of white oil is used.)
Cosmetic Industry
● ● Preparation of solid and liquid brilliantine Preparation of detergent creams, cold creams and beauty lotions
● ● ● Preparation of hydrated creams Preparation of bronzed oils Preparation of oil for hygiene of children
● Preparation of make-up products
Pharmaceutical Industry
● ● ● Antifoaming for the production of penicillin Internal lubricants as laxatives Additive in the machining of the
ingredients for the fabrication of the compressed Basis for ointments and emollients Vehicle of transport of● ●
medical spray
Packaging Industry for edible products
● Components for the lubricants of the tin band intended to be used for the tinned food
● Oiling of the cart and cartons for fruits and vegetables
The Plastic Material Industry
● ● ●Additive for the production of polyethylene Additive for extrusion of Polyvinyl Chloride Dispersant for
production of polyethylene Plasticizer for ethyl cellulose Plasticizer for coumarone-indene (resin) Plasticizer● ● ●
for EPDM (Ethylene-propylene-diene monomer) Plasticizer for polyethylene Plasticizer for poly-propylene● ●
Plasticizer for polystyrene Plasticizer for Annealing of the printed objects in nylon Hardening and annealing● ● ●
Textile Industry
● ● ● Oil components for spinning Oils for weaving and mesh Lubrication for sewing machines & hosiery
Various other industries
● ● Components for insecticide in agriculture Compressors for reactive gases like chlorine and sulphur dioxide
(lubrication of cylinders) Lubrication of paper cutter knives in paper mill Air filters for conditioning systems and● ●
under-water works
LIQUID PARAFFINS COLUMBIAPETROCHEM
Note:
1. The above data is indicated of recent average values only. Minor variations which do not affect performance or quality may be expected
in manufacture.
2. Specific requirements shall be custom-made on request
3. Light Liquid Paraffins / White Mineral Oils are manufactured in compliance with I.P., U.S.P., B.P. and Eph specifications and conforms to
the requirement of US FDA 21 CFR 172.878 (a) & (b)
COLUMBIA LIGHT LIQUID PARAFFINS
COLUMBIA HEAVY LIQUID PARAFFINS
TYPICAL PARAMETER LIGHT LIQUID PARAFFIN I.P.LIGHT LIQUID PARAFFIN
B.P./EPhLIGHT LIQUID PARAFFIN
U.S.P
Kinematic Viscosity @ 40ºC N.A. Not less than 33.5
Acidity / Alkalinity (Neutrality) Complies as per standard Complies as per standard
Solid Paraffin Complies as per standard Complies as per standard
Sulphur Compound N.A. N.A.
Readily Carbonisable Substance Complies as per standard Complies as per standard
Light absorption in the range 240 to 280 nm
N.A. N.A.
Polynucleur Aromatics Compound
Saybolt colour +30 +30+30
Odour and taste Odourless & Tasteless Odourless & TastelessOdourless & Tasteless
Dynamic Viscosity @ 20ºC, mPa s 25 to 80 N.A.25 to 80
N.A.
Specific Gravity @ 25ºC 0.810 to 0.875 0.818 to 0.8800.820 to 0.880
Complies as per standard
Complies as per standard
Complies as per standard
Complies as per standard
<0.1
N.A. Complies as per standard Complies as per standard
TYPICAL PARAMETER HEAVY LIQUID PARAFFIN I.P.HEAVY LIQUID PARAFFIN
B.P./EPhHEAVY LIQUID PARAFFIN
U.S.P
Kinematic Viscosity @ 40ºC N.A. Not less than 34.5
Acidity / Alkalinity (Neutrality) Complies as per standard Complies as per standard
Solid Paraffin Complies as per standard Complies as per standard
Sulphur Compound N.A. N.A.
Readily Carbonisable Substance Complies as per standard Complies as per standard
Light absorption in the range 240 to 280 nm
N.A. N.A.
Polynucleur Aromatics Compound
Saybolt colour +30 +30+30
Odour and taste Odourless & Tasteless Odourless & TastelessOdourless & Tasteless
Dynamic Viscosity @ 20ºC, mPa s 110 to 230 N.A.110 to 230
N.A.
Specific Gravity @ 25ºC 0.827 to 0.890 0.845 to 0.9050.860 to 0.904
Complies as per standard
Complies as per standard
Complies as per standard
Complies as per standard
<0.1
N.A. Complies as per standard Complies as per standard
LIQUID PARAFFINS COLUMBIAPETROCHEM
Recommended