View
10
Download
0
Category
Preview:
Citation preview
EverGuard Adhesives Guide
Updated: 3/17
INSULATION ADHESIVES
OlyBond500® is a two-component polyurethane low-rise foam adhesive used to adhere a variety of board stocks to most roof substrates or other insulation boards. Supplied in a bag-in-box for use with the PaceCart 2® application equipment.
• No thermal shorts caused by fasteners.• Chemical cure results in faster set-up time.• No pre-drilling into concrete. • Rapid application and strengthens system. • Helps to reduce reroofing and construction noise. • Lightweight and portable.• Contains no HCFCs and has low VOCs.
OlyBond500® Spot Shot (28-oz. tube) is a two-component polyurethane low-rise foam adhesive used to adhere a variety of board stocks to most roof substrates or other insulation boards. The tube set comes in a disposable cartridge to be used with the Spot Shot Application Gun.
• No thermal shorts caused by fasteners.• Chemical cure results in faster set-up time.• No pre-drilling into concrete. • Rapid application and strengthens system. • Helps to reduce reroofing and construction noise. • Great for repair work and small areas.• Stand-up application reduces worker fatigue while increasing production.
LRF Adhesive M is a two-part, VOC-free, fast-set polyurethane foam adhesive used for single-ply fleece-back membranes, most insulation, and substrates. This adhesive is applied on the substrate only.
• Replaces fasteners and minimizes excessive deck penetrations.• Low-rise foam that accommodates minor surface irregularities.• Solvent free, VOC free, and low odor.
GAF TPO LRF Adhesive M Low Temp is a two-component, VOC-free, low-rise polyurethane foam adhesive that contains no solvents and can be used to adhere both insulation boards and TPO fleece-back membrane in temperatures ranging from 25°F (-3.9° C) to 60°F (15.6°C).
• Replaces fasteners and minimizes excessive deck penetrations.• Low rise foam that accommodates minor surface irregularities.• Solvent free, VOC free, and low odor.
GAF 2-Part Roofing Adhesive is a low-rise‚ two-component polyurethane adhesive designed to adhere a variety of insulation board stock to various roof base substrates in both new and reroof applications.
• Self contained, ready to use. • Efficient in tight as well as open areas. • One kit = up to 20 squares.• No expensive spray equipment.• No external power required.• Fast installation.• Portable and user friendly.
SINGLE-PLY ADHESIVES
EverGuard® Low VOC TPO Bonding Adhesive is a contact-type bonding adhesive specially designed for bonding single-ply TPO roofing membranes and flashings to various roofing substrates.
• Low VOC (<250 g/L). • Approximately 6 square coverage per 5-gallon container.
EverGuard® TPO 3 Square Low VOC Bonding Adhesive is a contact-type bonding adhesive specially designed for bonding single-ply TPO roofing membranes and flashing to various roof substrates.
• Low VOC (<250 g/L). • Approximately 3 square coverage per 5-gallon container.
EverGuard® SBA 1121 TPO Bonding Adhesive is a solvent-based rubberized adhesive designed for use with TPO-based membranes.
• Fast-drying solvent system. • Easy application using roller, brush, or spray.
EverGuard® PVC Bonding Adhesive is a contact-type bonding adhesive specially designed for bonding PVC single-ply roofing membranes and flashings to various roofing substrates.
• Low VOC < 250 g/L.• Fast-drying solvent system.• Easy application using roller or brush.• High initial tack.
EverGuard® WB181 TPO Bonding Adhesive is a water-based adhesive designed for bonding both smooth and fleece-back TPO roofing membranes to various substrates.
• Compatible with concrete, masonry, metal, and wood flashing substrates.
LRF Adhesive O is a two-part polyurethane foam adhesive used for single-ply fleece-back membranes. This adhesive is applied on the substrate only.
• Replaces fasteners and minimizes excessive deck penetrations.• Low-rise foam that accommodates minor surface irregularities.• Solvent free, low VOC, and low odor.
GAF 2-Part Roofing Adhesive is a low-rise‚ two-component polyurethane adhesive specifically designed to adhere a variety of insulation board stock to various roof base substrates in both new and reroof applications.
• Self contained, ready to use. • Efficient in tight as well as open areas. • One kit = up to 20 squares.• No expensive spray equipment.• No external power required.• Fast installation.• Portable and user friendly.
Low VOC
Solvent Based
Water Based
LRF
OlyBond500®
AdhesiveOlyBond500® Spot Shot Adhesive
LRF Adhesive M LRF Adhesive M Low Temp
LRF Adhesive O GAF 2-Part Roofing Adhesive
Coverage Rate
OlyBond500® dispensed through the PaceCart 2® are 10 – 20 squares per 10-gallon bag-in-box sets
OlyBond500® Spot Shot dispensed through applicators is 4 – 6 squares per case (4 sets of 1500-ml cartridges)¾" – 1" max 12" o.c.
5-gallon kit: 1800 – 2200 sq. ft. 1.5-L cartridge: 400 – 600 sq. ft./ per case
1.5-L cartridge: 466 – 600 sq. ft./ per case
5-gallon kit: 1800 – 2200 sq. ft. 1.5-L cartridge: 400 – 600 sq. ft./per case
1800 – 2000 sq. ft. (2.5” bead, 12" on center rows)
VOC <5 g/L <5 g/L 0 g/L 0 g/L 32 g/L A-Component = 67.5 g/L B-Component = 67.5 g/L
Quantity/Size
10-gallon bag-in-box sets for use with the PaceCart 2® (5-gallon Part 1; 5-gallon Part 2)
4 sets of 1500-ml cartridges
Bag-in-box kit: 5-gallon box Cartridge: 4 1.5-L kits/carton
Cartridge: 4 1.5-L kits/carton
Bag-in-box kit: 5-gallon box Cartridge: 4 1.5-L kits/carton
A-Component = 12 Boxes B-Component = 12 Boxes
Weight Part 1 = 53 lb./box Part 2 = 45 lb./box
(4) 1500-ml cartridges: 19 lb.
Bag-in-box kit: 50 lb./box Cartridge: 20 lb./carton
Cartridge: 20 lb./carton
Bag-in-box kit: 50 lb./box Cartridge: 20 lb./carton
A-Component = 40 lb./box B-Component = 35 lb./box
EverGuard® Low VOC TPO Bonding Adhesive
EverGuard® 3 Sq. Low VOC TPO Bonding Adhesive
EverGuard® SBA 1121 TPO Bonding Adhesive
EverGuard® PVC Bonding Adhesive
EverGuard® WB181 TPO Bonding Adhesive
LRF Adhesive M
LRF Adhesive M Low Temp
LRF Adhesive O
Coverage Rate
EverGuard® Low VOC TPO Bonding Adhesive
50 – 60 sq. ft. per gallon
Up to 70 sq. ft. per gallon of bonded membrane
60 sq. ft. per gallon or 300 sq. ft. per pail
Smooth and fleece-back membrane is approximately 120 sq. ft. per gallon
5-gallon kit: 1800 – 2200 sq. ft. 1.5-L cartridge: 400 – 600 sq. ft./per case
1.5-L cartridge: 466 – 600 sq. ft./ per case
5-gallon kit: 1800 – 2200 sq. ft. 1.5-L cartridge:400 – 600 sq. ft./per case
VOC 247 g/L <250 g/L 611 g/L < 250 g/L 8 g/L 0 g/L 0 g/L 32 g/L
Quantity/Size
5-gallon pail 5-gallon pail 5-gallon pail 5-gallon pail 5-gallon pail Bag-in-box kit: 5-gallon box Cartridge: 4 1.5-L kits/carton
Cartridge: 4 1.5-L kits/carton
Bag-in-box kit: 5-gallon box Cartridge: 4 1.5-L kits/carton
Weight 40 lb./pail 38 lb./pail 37 lb./pail 36 lb./pail 45 lb./pail Bag-in-box kit: 50 lb./box Cartridge: 20 lb./carton
Cartridge: 20 lb./carton
Bag-in-box kit: 50 lb./box Cartridge: 20 lb./carton
INSULATION ADHESIVES
SINGLE-PLY ADHESIVES
PRIMERS
SEALANTS
Low VOC TPO Primer is designed for use with EverGuard® TPO membrane and EverGuard® Freedom™ TPO self-adhered products.
• Useful for ensuring good adhesion between adhesives, sealants, and EverGuard® TPO single-ply roofing membranes.
• Low VOC content of 240 grams/liter.
Quantity/Size 6 - 1-gallon cans/carton Weight 59 lb./carton
EverGuard® TPO Primer is designed for use with EverGuard® TPO membrane and EverGuard® Freedom™ self-adhered TPO products.
• Solvent-based primer for metal edges and cover tape.
• Useful for ensuring good adhesion between adhesives, sealants, and EverGuard® TPO single-ply roofing membranes.
Quantity/Size 6 - 1-gallon cans Weight 56 lb./carton
TPO Red Primer is a VOC-compliant, solvent-based liquid that is applied to new or aged TPO membranes to promote adhesion of water-based coatings or MajorSeal™ Liquid Flashing. It is lightly tinted red to discern primed areas on bright white TPO membranes.
• Promote adhesion of water-based coating to TPO.• VOC compliant.
Quantity/Size 6 - 1-gallon cans/carton Weight 56 lb./carton
GAF Pourable Sealant (Two-Part) is a 100% solid, urethane-based two-part sealant.
• Suitable for filling sealant pans at irregularly shaped penetrations.
Quantity/Size 1 kit = 1-gallon part A, 1-pint part B (2 kits per box with mixer and gloves) Weight 18 lb./carton
GAF WaterBlock Mastic is a one-part, butyl-based, high-viscosity sealant.
• Suitable for sealing between flashing membrane and substrate surface behind exposed termination bars. • Suitable for sealing between roofing membrane and drain flanges.
Quantity/Size 25 tubes/carton Weight 27 lb./carton
GAF FlexSeal™– Caulk Grade is a solvent-based synthetic elastomeric sealant. It is designed to maintain an effective bond and seal between materials of similar and dissimilar surfaces.
• Extremely flexible and durable.• Ideal for termination bar, railing, step flashings, or edge metal.• Durable and UV resistant; will not chalk, crack, or peel.
Quantity/Size 20 - 10-oz. tubes/box Weight 19 lb./box
EverGuard® One-Part Pourable Sealant is a one-part, moisture-cure, self-leveling sealant designed for use in pitch pans on single-ply roof systems.
• Self-leveling provides a smooth, professional finished look.• Application at temperatures as low as 30°F (-1°C).
Quantity/Size 4 pouches/case Weight .053-gallon pouch
©2017 GAF 3/17 • #897 • 1 Campus Drive, Parsippany, NJ 07054
Recommended