View
25
Download
0
Category
Preview:
Citation preview
EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide UG-1046
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the AD5541A and the AD5542A, 16-Bit, Accurate, High
Precision DAC in LFCSP with 1 µs Settling Time and 5 kV ESD Ratings
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 12
FEATURES Full featured evaluation board for the AD5541A and the
AD5542A On-board reference Various link options PC control in conjunction with Analog Devices, Inc.,
EVAL-SDP-CB1Z PC software for control of DACs
EVALUATION KIT CONTENTS EVAL-AD5541A evaluation board or the EVAL-AD5542A
evaluation board AD5541A device or the AD5542A device CD includes
Self installing evaluation software allowing users to control the board and exercise all functions of the device
Electronic version of the AD5541A data sheet or the AD5542A data sheet
Electronic version of the EVAL-AD5541A user guide or the EVAL-AD5542A user guide
AD5541A/42A Evaluation Software USB cable
GENERAL DESCRIPTION The EVAL-AD5541ASDZ evaluation board and the EVAL-AD5542ASDZ evaluation board are designed to quickly prototype the AD5541A and AD5542A circuits, respectively, and reduce design time. The AD5541A and the AD5542A operate from a single 2.7 V to 5.5 V supply. The REF192 is the on-board reference chip.
The EVAL-AD5541ASDZ evaluation board and the EVAL-AD5542ASDZ evaluation board interface to the USB port of a PC via the EVAL-SDP-CB1Z board. The AD5541A/42A Evaluation Software is available with the evaluation boards or from the evaluation board webpage, which allows the user to program the AD5541A or the AD5542A.
Full specifications for the AD5541A are listed in the AD5541A data sheet and full specifications for the AD5542A are listed in the AD5542A data sheet available from Analog Devices and should be consulted in conjunction with this user guide when using the evaluation boards.
UG-1046 EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide
Rev. 0 | Page 2 of 12
TABLE OF CONTENTS Features .............................................................................................. 1
Evaluation Kit Contents ................................................................... 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Universal Evaluation Board ............................................................. 3
Evaluation Board Hardware ............................................................ 4
Power Supplies .............................................................................. 4
Link Options ................................................................................. 4
Evaluation Board Software ...............................................................6
Installing the Software ..................................................................6
Running the Software ...................................................................6
Software Operation .......................................................................7
Evaluation Board Schematics and Artwork ...................................8
Ordering Information .................................................................... 11
Bill of Materials ........................................................................... 11
REVISION HISTORY 6/2017—Revision 0: Initial Version
EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide UG-1046
Rev. 0 | Page 3 of 12
UNIVERSAL EVALUATION BOARD
1500
9-10
1
Figure 1.
UG-1046 EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide
Rev. 0 | Page 4 of 12
EVALUATION BOARD HARDWARE POWER SUPPLIES To power the EVAL-AD5542ASDZ evaluation board, supply 5 V between the +5V input and AGND input for the analog supply and −5 V between the −5V input and AGND input for the negative analog supply of the evaluation board.
To power the EVAL-AD5541ASDZ evaluation board, connect the evaluation board to the EVAL-SDP-CB1Z board, which is powered by the USB interface on the PC.
All supplies are decoupled to ground with 10 µF tantalum capacitors and 0.1 µF ceramic capacitors. Table 1 describes the power supply connectors.
Table 1. Power Supply Connectors Connector Voltage J1 Analog positive power supply is +5 V and AGND. Analog negative power supply is −5 V and AGND. Single-supply operation supply is +5 V and −5 V.
LINK OPTIONS A number of link and switch options are incorporated in the EVAL-AD5541ASDZ and EVAL-AD5542ASDZ evaluation boards that must be set for the required operating conditions before using the evaluation boards. Table 2 and Table 3 describe the positions of the different links controlling the evaluation boards by PC via the USB port. The functions of these link options are described in detail in Table 4.
Table 2. Link Position Setup for the EVAL-AD5541ASDZ Link Position LK1 A LK2 A LK3 A LK4 A LK5 Not inserted LK6 Not inserted LK7 B LK8 A LK9 B
Table 3. Link Position Setup for the EVAL-AD5542ASDZ Link Position LK1 B LK2 A LK3 B LK4 B LK5 B LK6 Inserted LK7 A LK8 B LK9 A
EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide UG-1046
Rev. 0 | Page 5 of 12
Table 4. Link Functions Link Functions1 LK1 This link selects the output configuration of the OP777 or the AD8628. Position A connects the noninverting input of the OP777 or the AD8628 to VOUT. Position B connects the output of the buffer of the OP777 or the AD8628 to VOUT. LK2 This link selects the reference source. Position A selects the on-board 2.5 V reference as the reference source. Position B selects J2 as the reference source. LK3 This link selects which digital-to-analog converter (DAC) connects to the reference source. Position A connects the reference source to the AD5541A. Position B connects the reference source to the AD5542A. LK4 This link selects which DAC connects to the noninverting input of the OP777 or the AD8628. Position A connects the noninverting input of the buffer to the AD5541A. Position R connects the noninverting input of the buffer to the AD5542A. LK5 This link selects which connection connects to the output (feedback path) of the OP777 or the AD8628. Position A connects the inverting input of the OP777 or the AD8628 to the output of the OP777 or the AD8628. Position B connects the RFB pin of the AD5542A to the output of the OP777 or the AD8628. LK6 Connects the INV pin of the AD5542A to the inverting terminal of the OP777 or the AD8628. LK7 This link determines which DAC is being addressed via the serial interface by switching the CS line between both DACs.
Position A connects the digital circuitry to the AD5542A. Position B connects the digital circuitry to the AD5541A. LK8 This link selects the positive voltage supply for the EVAL-AD5541ASDZ and the EVAL-AD5542ASDZ evaluation boards. Position A connects the positive board supply from the ADP121. The ADP121 is powered by the PC USB interface. Position B connects the positive board supply voltage to the J1_+5V power connector for the EVAL-AD5541ASDZ and the
EVAL-AD5542ASDZ evaluation boards. LK9 This link selects the negative voltage supply for the board. Position A connects the negative voltage supply to the J1_−5V power connector (EVAL-AD5542ASDZ evaluation board only). Position B connects the negative voltage supply to GND (EVAL-AD5541ASDZ evaluation board only). 1 The EVAL-AD5542ASDZ uses the OP777 and the EVAL-AD5541ASDZ uses the AD8628.
UG-1046 EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide
Rev. 0 | Page 6 of 12
EVALUATION BOARD SOFTWARE INSTALLING THE SOFTWARE The EVAL-AD5541ASDZ and the EVAL-AD5542ASDZ evaluation kits include self installing evaluation software on the provided CD, and can also be downloaded from the EVAL-AD5541A or the EVAL-AD5542A product pages. The software is compatible with Windows® XP, Windows Vista (32-bits), and Windows 7 (32-bits).
Install the software before connecting the EVAL-SDP-CB1Z board to the USB port of the PC to ensure the PC recognizes the EVAL-SDP-CB1Z board when it connects to the PC.
1. Start the Windows operating system and insert the CD. 2. The installation software opens automatically. If it does not
open automatically, run the setup.exe file from the CD. 3. After the installation is complete, power up the evaluation
board as described in the Power Supplies section. 4. Plug the EVAL-AD5541A or EVAL-AD5542ASDZ into the
EVAL-SDP-CB1Z board and the EVAL-SDP-CB1Z board into the PC using the USB cable included in the evaluation kit.
5. When the software detects the evaluation board, proceed through any dialog boxes that appear to finalize the installation.
RUNNING THE SOFTWARE To run the software, do the following:
1. Click Start > All Programs > Analog Devices > AD5541A_42A > AD5541A_42A Evaluation Software.
2. If the EVAL-SDP-CB1Z board does not connect to the USB port when the software launches, a connectivity error displays (see Figure 2). Connect the evaluation board to the USB port of the PC, wait a few seconds, click Rescan, and follow the instructions.
1500
9-00
2
Figure 2. Hardware Select Window
3. If the EVAL-SDP-CB1Z board does not connect to the PC, the ERROR CONNECTION window appears, shown in Figure 3. Check the connection between the EVAL-SDP-CB1Z and EVAL-AD5541A board or EVAL-AD5542ASDZ board and run the program again.
1500
9-00
3
Figure 3. ERROR CONNECTION Window
4. If the EVAL-SDP-CB1Z board connects, the System Development Platform Wait window displays.
1500
9-00
4
Figure 4. System Development Platform Wait Window
5. The Select Device window opens, shown in Figure 5, allowing the user to select the AD5541A or the AD5542A.
1500
9-00
5
Figure 5. Select Device Window
EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide UG-1046
Rev. 0 | Page 7 of 12
6. The AD5542A/41A Evaluation Software window opens, as shown in Figure 6.
1500
9-00
6
Figure 6. AD5541A/42A Evaluation Software V2.1 Window
SOFTWARE OPERATION The AD5542A/41A Evaluation Software main window is shown in Figure 6. The data programmed into the 16-bit input shift register displays.
To write data to the 16-bit input register, type the data in decimal format under Data Bits. To execute, click Write to Part.
The EVAL-AD5541ASDZ evaluation board and the EVAL-AD5542ASDZ evaluation board lets users set up the LDAC pin to load data from the input register to the DAC output register.
The CLR pin is only available on the EVAL-AD5542ASDZ evaluation board, and when activated, the DAC register is cleared to the model selectable midscale. Consult the AD5541A data sheet and the AD5542A data sheet to see which device has a CLR pin and what its function is for each model.
Set LDAC pin or the CLR pin to high or low by clicking LDAC or CLR, respectively. This command executes immediately, so there is no need to click Write to Part.
For the AD5541A, it is suggested that users connect a voltmeter to LK4 and measure the output voltage at this point.
UG-1046 EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide
Rev. 0 | Page 8 of 12
EVALUATION BOARD SCHEMATICS AND ARTWORK
R9 0r
R11 0r
R15 0r
C120.1uF
+C13
10 uF± 20 %
C20
0. 1uF
TP1
TP3
TP9 TP10 TP11
J2
BA
LK7
1VD
D
2VOUT
3A
GN
D
4R
EF
5 CS
6 SCLK
7 DI N
8LDAC
9D
GN
D
10VLOGI C
U1AD5541 ABCPZ
C6 0. 1uF
+
C5 10 uF
± 20 %
C3 0.1uF
+
C4 10 uF± 20 %
2
3 +
6- 7
OUT
4
U6OP97
LK6
BA
LK4
2-
3+
6OP
4V-
7V+
U7
AD8628
C15 0. 1uF
+
C14 10 uF
±20
%
C19 0. 1uF
+
C18 10 uF± 20 %
2 -
3 +
6OP
4V-
7V+
U9
C17 0. 1uF
+
C16 10 uF± 20 %
1VOUT
2A
GN
GF
3A
GN
DS
4R
EF
S
5R
EF
F
6 CS
7N
C
8 SCLK
9 DI N
10CLR
11LDAC
12D
GN
D
13I NV
14V
LOG
IC
15V
DD
16R
FB
U2AD5542A
1R
EF2 + I N3-I N
4G
ND
5CS 6DOUT
7DCLK
8V
DD
U4
AD7683 _ ADC
C7 0. 1uF
BA
LK5
C11 0. 1uF
+
C10 10 uF
±20
%
C9 0. 1uF
BA
LK1VOUT
J1-1
J1-2
J1-3
C1
0.1uF+
C2
10 uF± 20 %
BA
LK2
BA
LK3
R1 0r
R2 0r
+
C8 10 uF
±20
%
1I N
2GND
3EN
5OUT
4NC
U11
ADP121
C211uF
BA
LK8
BA
LK9
C22 1uF
6O/ P2 VI N
3 SLEEP
4
GND
U3
REF192
CLR
/ LDAC
DAC_SYNC
DAC_DI N
DAC_SCLK
VNEG
VPOS
VPOS
VPOS
VNEG
VPOS
VNEG
ADC_SCLKADC_CSADC_SDATA
VPOS
VPOS
V_I O
V_I O
USB_PW R
VPOS_EXT
VPOS
1500
9-00
7
Figure 7. Schematic of Evaluation Circuitry
EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide UG-1046
Rev. 0 | Page 9 of 12
VIN: Use th is p in to power the SDP requi res 4V to 7V 200mA
V I O: Us e t o s et I O v ol t a ge m ax dra w 20 m A
I 2 C bu s 1 is com m on across bo t h conn e ct o rs on SDP - Pu ll u p re si st o rs r equ i re d
BMODE1 : Pu ll u p w i t h a 10kΩ re si st o r t o s et SDP t o bo ot f ro m a SPI f l a s h on t he da ug ht er bo ard
(co nn ect ed t o Black f in GPI O - u se I 2 C_0 f i rs t )
* NC o n BLACKFI N SDP
****
****
*
**
**
T I MERS
I NPUT / OUT PUTGENERAL
I 2 C
SPI
SPORT
PORTPARALLEL
SDPSTA NDARD
CONN ECTOR
12 0NC
11 9NC
11 8GND
11 7GND
11 6VI O( + 3 .3V)
11 5GND
11 4PA R_D2 2
11 3PA R_D2 0
11 2PA R_D1 8
11 1PA R_D1 6
11 0PA R_D1 5
10 9GND
10 8PA R_D 12
10 7PA R_D 10
10 6PAR_ D8
10 5PAR_ D6
10 4GND
10 3PAR_ D4
10 2PAR_ D2
10 1PAR_ D0
10 0PAR_ W R
99PAR_ I NT
98GND
9 7PA R_ A2
9 6PA R_ A0
9 5PAR_ FS2
9 4PAR_CLK
9 3GND
9 2SPORT_RSCLK
9 1SPORT_D R0
9 0SPORT_ RFS
8 9SPORT_ TFS
8 8SPORT_DT0
8 7SPORT_TSCLK
86GND
8 5SPI _SEL_A
8 4SPI_ MOSI
8 3SPI_ MI SO
8 2SPI _CLK
8 1GND
8 0SDA_ 0
7 9SCL_ 0
7 8GPI O1
7 7GPI O3
7 6GPI O5
7 5GND
7 4GPI O7
7 3TMR_ B
7 2TMR_D
7 1NC
7 0NC
6 9GND
6 8NC
6 7NC
6 6NC
6 5NC
6 4NC
6 3GND
6 2UART_TX
6 1BMODE1
6 0RESET_I N5 9UART_RX5 8GND
5 7NC
5 6NC
5 5NC5 4NC5 3NC
5 2GND
5 1NC
5 0NC4 9TMR_ C4 8TMR_ A4 7GPI O6
4 6GND
4 5GPI O44 4GPI O24 3GPI O04 2SCL_1
4 1SDA _1
4 0GND3 9SPI _SEL1/ SPI _SS3 8SPI _SEL_C3 7SPI _SEL_B
3 6GND
3 5SPORT_ I NT34SPORT_ DT333SPORT_ DT232SPORT_ DT1
31SPORT_ DR1
30SPORT_ DR2
29SPORT_ DR328GND27PAR_FS1
26PAR_FS3
25PAR_A 1
24PAR_A 323GND22PA R_CS
2 1PAR_RD
2 0PAR_D1
1 9PAR_D31 8PAR_D51 7GND1 6PAR_D7
1 5PAR_D9
1 4PAR_D1 11 3PAR_D1 31 2PAR_D1 41 1GND
1 0PAR_D1 7
9PAR_D1 98PAR_D2 17PAR_D2 36GND
5USB _VB US
4GND3GND2NC1VI N
U1 0
1A0
2A1
3A24VSS
8VCC
7W P
6SCL 5SDA
U8
24 LC32
1 OE
2A 0
4A 1
6 A 28 A 3
18Y0
16Y1
14Y212Y3
U 5 - A
74 H C T24 4
R3
10 k
R4
10 k
R5
10 k
C39
0 .1u F
+ C50
10 u F± 20 %
19 OE
11A 0
13A 1
15A 2
17 A 3
9Y07
Y15
Y23Y3
U 5 - B
74 H C T24 4
TP2
R6 0 r
V_ I O
SDA_ 0SCL_0
/ LDAC CLR
V_ I O
VPOS_EXT
RX_DA TA
V _I O
A DC_CSA DC_ SCLKA DC_SDATA
DA C_SYNCDA C_ SCLKDA C_ DI N
ADC
DAC
TX _DA TACLK
FRA MESYNCADC_ SDA TA
FRA MESYNCCLK
TX _DA TA
V _I O
RX_DA TA
FRAM ESY NCTX_D ATACLK
DAC ADC
V _I O
USB _PW R
EE PROM_ A0
EEPROM_ A0
1500
9-00
8
Figure 8. Schematic of SDP Connector
1500
9-00
9
Figure 9. Component Placement Drawing
UG-1046 EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide
Rev. 0 | Page 10 of 12
1500
9-01
1
Figure 10. Component Side PCB Drawing
1500
9-01
0
Figure 11. Solder Side PCB Drawing
EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide UG-1046
Rev. 0 | Page 11 of 12
ORDERING INFORMATION BILL OF MATERIALS
Table 5. EVAL-AD5541ASDZ Board Reference Designator Description Part Number U1 Precision 16-bit, 1 µs setting time DAC AD5541A U6 Low power, precision CMOS amplifier AD8628 U11 3.3 V linear regulator ADP121 LK6 2-pin (0.1'' pitch) headers FEC 1022247 LK1 to LK5, LK7 to LK9 3-pin (0.1" pitch) headers FEC 1022249 J2, VOUT 50 Ω straight SMB jacks FEC 1111349 C1, C6, C9, C11, C12, C20, C39 0.1 µF, 16 V, X7R ceramic capacitors FEC 1216538 U10 120-way connector, 0.6 mm pitch FEC 1324660 J1 3-pin terminal block, 5 mm pitch FEC 151-790 C21, C22 1 µF, 16 V, X7R, ceramic capacitors FEC 1658870 C2, C5, C8, C10, C13, C50 Ceramic capacitors,10 µF, 10 V, X5R, 0603 FEC 1853538 SCREW1, SCREW2 Screws, cheese, nylon, M3X16, PK100 FEC 7070615 TP1 to TP3, TP9 to TP11 Test points FEC 8731128 R1 to R3, R11, R15 0 Ω resistors FEC 9331662 R3 to R5 10 kΩ resistors FEC 933-2413 U5 Octal buffer/line driver three-state outputs FEC 9591915 U8 32 K I2C serial EEPROM FEC1331330 U3 Reference REF192ESZ
Table 6. EVAL-AD5542ASDZ Board Reference Designator Description Part Number U2 Precision 16-bit, 1 µs setting time DAC AD5542A U7 Low power, precision CMOS amplifier AD8628 U9 Precision CMOS amplifier AD8638 U11 3.3 V linear regulator ADP121 LK6 2-pin (0.1" pitch) header FEC 1022247 U6 Operational amplifier OP777 LK1 to LK5, LK7 to LK9 3-pin (0.1" pitch) headers FEC 1022249 J2, VOUT 50 Ω straight SMB jacks FEC 1111349 C1, C3, C9, C11, C12, C15, C17, C19, C20, C39 0.1 µF, 16 V, X7R ceramic capacitors FEC 1216538 U10 120-way connector, 0.6 mm pitch FEC 1324660 J1 3-pin terminal block, 5 mm pitch FEC 151-790 C21, C22 1 µF, 16 V, X7R, ceramic capacitors FEC 1658870 C2, C4, C8, C10, C13, C14, C16, C18, C50 Ceramic capacitors, 10 µF, 10 V, X5R, 0603 FEC 1853538 SCREW1, SCREW2 Screws, cheese, nylon, M3X16, PK100 FEC 7070615 TP1 to TP3, TP9 to TP11 Test points FEC 8731128 R1, R2, R3, R9, R11, R15 0 Ω resistors FEC 9331662 R3 to R5 10 kΩ resistors FEC 933-2413 U5 Octal buffer/line driver three-state outputs FEC 9591915 U8 32 K I2C serial EEPROM FEC1331330 U3 Reference REF192ESZ
UG-1046 EVAL-AD5541ASDZ/EVAL-AD5542ASDZ User Guide
Rev. 0 | Page 12 of 12
NOTES
I2C refers to a communication protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG15009-0-6/17(0)
Recommended