View
0
Download
0
Category
Preview:
Citation preview
Page Part Description Page Part Description
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
2 HydroDrill Layout3 HydroDrill Replacement Parts4,5 HydroDrill User Instructions6 HydroDrill Augers7 Right Angle Wrench8 Right Angle Wrench Descriptions9 Right Angle Wrench
Essentials Only10 Right Angle Wrench Replacement
Parts11 Combined Right Angle Wrench &
Clean Out Plug Wrench Set12 Clean Out Plug Wrench Sets13 Clean Out Plug Wrench
Replacement Parts14 Clean Out Plug Wrench Set
with Reversing Ratchet Wrench15 Clean Out Plug Wrench Ratchet
Set Replacement Parts16 Clean Out Plug Wrench Sets - No
Carrying Case
17 3/4" Drive Ratchet Wrench18 Valve Operator Key Set19 Spud Nut Wrench20 Water Meter/City Meter Keys21 Double Slotted Water Meter Key22 ABS Adaptor (NST to IPS)23 Sloan Tailpiece Tool24 Faucet Nut Saw25 Emergency Gas Shut-Off Wrench26 Tailpiece Flanging Tool27 Tailpiece Flanging Tool
Instructions28 Stuvel Flush Valve Reseater29 Tile Probes30 Band-Aid Pipe Clamp31 Miscellaneous Tools32 Floor Drain Wrench33 Sinklear Garbage Disposal
Installer Tool34 In-Sink Installer Tool for Garbage
Disposal Flange35 Erickson Drain Cleaner Snakes
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
PERFECTO HYDRODRILL LAYOUT
HOW THE HYDRODRILL WORKS:The Chuck Adaptor is inserted into the chuck of your drill. The Chuck Adaptor, the Shaft and the MalePipe Fitting are all solidly attached together, and rotate with the drill. The Shaft Bearings allow the Shaft toturn freely. A hose is attached to the Hose Fitting. When the water is turned on and the valve is opened,water runs through the valve and into the Hydrodrill body. The Shaft Seals keep the water from leaking out.There is a hole in the side of the Shaft, and another hole that runs down the length of the Shaft out the end.The water enters the side hole and runs out the end. From there it fills the pipe attached to the Male PipeFitting, and from there out through the Hydrodrill Auger.
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
REPLACEMENT PARTS FOR THE #1HYDRODRILL (PART No. 1502)
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
#1 HYDRO-DRILL: 5/8" Shaft
The power for drilling is supplied by a 1/2" drill –
preferably a 450 RPM drill. Water is supplied to break
up the ground and help keep the bit cool while drilling.
YOU CAN BORE UP TO 200 FEET FOR 1/2" to 8" PIPE!
The HYDRO-DRILL is a rugged tool,
designed with the best materials available.
The chuck-end is manufactured from an
alloy steel to prevent breakage due to
impact shock. The threaded male end is
forged steel for wear strength, and the blade
is welded steel with a hard facing on the
cutting edges of the blades, to give them a
longer drill life.
This very versatile earth boring tool is used to
eliminate excavating when putting in utility services
under existing driveways, sidewalks or landscapes.
The standard HYDRO-DRILL kit comes with a 2"
bit. Additional standard bits are available in 1"
through 12" sizes. Carbide tipped auger bits are
available in 1-1/4", 1-1/2" and 2" sizes.
HYDRO-DRILL
BEFORE USING, READ CAREFULLY
INSTRUCTIONS FOR OPERATING THE HYDRO-DRILL
IN BORING A HOLE, CAREFULLY ALIGN PIPE WITH THE OPPOSITE SIDE. IF YOU STAY ON TARGET
FOR THE FIRST TEN FEET, THE TOOL WILL RUN STRAIGHT FOR THE REMAINDER OF THE BORE. SET
THE DESIRED GRADE WITH A LEVEL.
PLEASE OIL FREQUENTLY WITH A GOOD LUBRICATING OIL ON BOTH THE INSIDE AND OUTSIDE, ON
THE SHAFT.
DIFFERENT SOILS WILL REQUIRE DIFFERENT AMOUNTS OF BOTH WATER AND PRESSURE ON THE
TOOL. FOR EXAMPLE, IN GUMMY, STIFF DIRT OR CLAY, A 3" BIT WILL DRILL FASTER THAN A 2" BIT.
WHEN BORING THROUGH ROCKY SOIL, BORE WITH CAUTION. IF YOU HIT A ROCK, THE BIT WILL
VEER OFF TRACK. IF THIS HAPPENS, THE DRILL SHOULD BE SHUT OFF AND THE WATER LEFT
RUNNING. WITH SEVERAL FORWARD AND BACKWARD MOTIONS YOU CAN USUALLY PUSH THE
ROCK ASIDE SO THAT THE BIT WILL PASS WITHOUT LOSING IT’S ALIGNMENT. IF THIS DOES NOT
WORK, TURN THE DRILL ON AND MOVE VERY SLOWLY UNTIL THE BIT HAS MADE A GROOVE IN THE
ROCK. THEN IT WILL NOT SLIP OUT OF ALIGNMENT AND YOU MAY EXERT MORE PRESSURE. (WE
DO NOT GUARANTEE OUR BITS AS ROCK BITS, BUT USERS ARE GENERALLY GETTING GOOD
RESULTS.)
HELPFUL HINTS TO ENSURE PROPER BORING:
• NEVER PUT SIDE PRESSURE ON THE DRILL. THE PRESSURE MUST BE EXERTED IN A
STRAIGHT FORWARD MOTION. SIDE PRESSURE OR PUTTING “ENGLISH” ON THE DRILL WILL
WEAR OUT THE BEARINGS PREMATURELY.
• YOU MUST AT ALL TIMES RUN THE TOOL WITH WATER, AND USE A STRAIGHT PIECE OF
PIPE.
• IT IS A GOOD IDEA TO USE A DRILL WITH A CHUCK NO LARGER THAN 3/4". WE RECOMMEND
A 1/2" DRILL FOR THE #1 HYDRO-DRILL. THREADS ON COUPLINGS SHOULD BE CHECKED
FREQUENTLY. IF THEY ARE WORN, THEY SHOULD BE REPLACED.
• TO GET BEST RESULTS, USE A 450 RPM DRILL. DO NOT USE A DRILL OVER 700 RPM. DO NOT
USE AN AIR IMPACT TOOL OR AN ELECTRIC IMPACT TOOL.
• TAKE YOUR TIME – IT IS MUCH BETTER TO BORE SLOWLY AND CAREFULLY THAN
HURRIEDLY.
IN BORING WITH A 4" OR LARGER BIT, MAKE A 2" BORE AS ABOVE. THEN REMOVE THE 2" BIT AND
REPLACE IT WITH A 4" OR LARGER REVERSE BIT. THEN SIMPLY BACK OUT OF THE HOLE YOU JUST
DUG. DO NOT REVERSE THE DIRECTION OF THE DRILL!! THE REVERSE BITS ARE DESIGNED TO
WORK WITH THE DRILL MOTOR RUNNING IN THE FORWARD DIRECTION. RUNNING THE DRILL
MOTOR IN REVERSE WILL UNSCREW THE PIPE THREADS AND LEAVE YOUR EXPENSIVE BIT
SOMEWHERE IN THE MIDDLE OF THE HOLE.
BE SURE TO MAINTAIN A CONSTANT DRILL SPEED WHEN THE REVERSE BORE IS BEING MADE. THIS
ASSURES YOU OF A CLEAN BORE, AND SAVES UNDUE STRAIN ON YOUR DRILL. THE PIPE SHOULD
THEN BE IMMEDIATELY INSTALLED INTO THE BORE.
CAUTION! This unit should NOT be used without proper grounding. Attach the included ground wire to the water
inlet valve, and to any solid ground, preferably a steel rod driven into the ground. More wire may be needed than the
length provided.
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
AUGERS FOR THE HYDRODRILL
1" FORWARD PART 1504-1 4" REVERSE PART 1504-4R2" FORWARD PART 1504-2 6" REVERSE PART 1504-6R3" FORWARD PART 1504-3 8" REVERSE PART 1504-8R4" FORWARD PART 1504-4F2" CARBIDE AUGER PART 1504-200C
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
This is the best tool for the worst jobs! Justbecause the plumbing is in a tight space doesn’tmean you have to crawl into it. Let Perfecto’sRight Angle Wrench do the crawling for you!
Set the wrench head on the pipe or thestubborn nut and make sure the grip is tight. Then insert the extension piece into the socket onthe wrench head. With the T-handle on the otherend of the extension, you’re ready to twist awaywithout having to worry about bruised knucklesor scraped skin.
You can even plug the T-handle straight intothe wrench head for other situations.
Need to tighten down on the slip nut? Justput the wrench head in your hand and snug up theconnection without any handle getting in yourway.
PERFECTO RIGHT ANGLE WRENCHAlso available with a complete
Deluxe Set (Shown): Part No. 1700D set of Clean Out Plug WrenchesSuper Deluxe Set: Part No. 1700SD In a single box (Part No. 1700-DWP)
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
RIGHT ANGLE WRENCH SETSDifferences between DELUXE and SUPER DELUXE sets
DELUXE For the deluxe sets, the handle is a forged sliding T-bar. It has a 3/4" male endthat fits into a 3/4" female socket on the DELUXE extension. The overall lengthof the extension is 28".
SUPER DELUXE The handle for the SUPER DELUXE is identical to the DELUXE. The differenceis that the extension consists of two (count ‘em, two) extensions, each 17" long, sothe overall length of the extension is 34".
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
PERFECTO RIGHT ANGLE WRENCHDELUXE – ESSENTIALS ONLY
PART No 1700-DE
This kit includesonly the parts seenhere: The SlidingT-Bar, the 28”Extension. And theWrench Head
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
REPLACEMENT PARTS FOR THE RIGHT ANGLE WRENCHES
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399)website: www.perfectoproducts.net C E-MAIL: sales@perfectoproducts.net
PERFECTO COMBINED WRENCH SETDeluxe Right Angle Wrench Set with a complete set of Clean Out PlugWrenches: Part No. 1700-DWP
This set combines two of our most popular tool kits: The Deluxe Right Angle Wrench, and the
11 piece Clean Out Plug Wrench Set. All the pieces fit into a single box, so you save valuable
floor space in your truck. The 19" sliding T-Bar can be used with or without the 28" extension.
Don’t crawl in to a cramped space to get at the problem, let our tool do that for you. Access
plus leverage, and now add a clean out plug wrench for most popular sizes and styles. The
perfect combination.
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
CLEAN-OUT PLUG WRENCHESFITS RAISED HEAD, COUNTERSUNK OR SLOTTED CLEAN OUT PLUGS
PART No 1701-CPX: COMPLETE SET (10 PIECES w/ BOX and HANDLEPART No 1701-CPW: COMPLETE SET (10 PIECES w/ BOX NO HANDLE
Wrench Description Part Number Wrench Description Part NumberRaised Head: 7/8” ID 1701-RHW #1 Countersunk: 7/8” Square 1701-CSW #7Raised Head: 1-1/16” ID 1701-RHW #2 Countersunk: 1-1/8” Square 1701-CSW #8Raised Head: 1-1/4” ID 1701-RHW #3 Countersunk: 1-1/4” Square USE 1701-RHW #1Raised Head: 1-3/4” ID 1701-RHW #4 Slotted: 1/4” x 1” 1701-SSW #10Raised Head: 2-1/8” ID 1701-RHW #5 Slotted: 1/4” x 1-3/4” 1701-SSW #11Countersunk: 3/4” Square 1701-CSW #6 Slotted: 1/4” x 2-1/2” 1701-SSW #12 (Special Order)
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
REPLACEMENT PARTS FOR CLEAN OUTPLUG WRENCH SETS
Wrench Description Part Number Wrench Description Part NumberRaised Head: 7/8” ID 1701-RHW #1 Countersunk: 7/8” Square 1701-CSW #7Raised Head: 1-1/16” ID 1701-RHW #2 Countersunk: 1-1/8” Square 1701-CSW #8Raised Head: 1-1/4” ID 1701-RHW #3 Countersunk: 1-1/4” Square USE 1701-RHW #1Raised Head: 1-3/4” ID 1701-RHW #4 Slotted: 1/4” x 1” 1701-SSW #10Raised Head: 2-1/8” ID 1701-RHW #5 Slotted: 1/4” x 1-3/4” 1701-SSW #11Countersunk: 3/4” Square 1701-CSW #6 Slotted: 1/4” x 2-1/2” 1701-SSW #12 (Special Order)
221 W. Santa Fe Avenue, Fullerton, CA 92832 (714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
THE CLEAN OUT PLUG WRENCH SET
WITH REVERSING RATCHET WRENCH
Part No 1701-CPR
1701-RHW #1 Raised Head: 7/8” ID 1701-CSW #6 Countersunk: 3/4” SQ
1701-RHW #2 Raised Head: 1-1/16” ID 1701-CSW #7 Countersunk: 7/8” SQ
1701-RHW #3 Raised Head: 1-1/4” ID 1701-CSW #8 Countersunk: 1-1/8” SQ
1701-RHW #4 Raised Head: 1-3/4” ID 1701-RHW #1 Countersunk: 1-1/4” SQ
1701-RHW #5 Raised Head: 2-1/8” ID 1701-SSW #10 Slotted” 1/4”x 1”
1701-SSW #11 Slotted: 1/4” x 1-3/4”
(Plugs Not Included)
221 W. Santa Fe Avenue, Fullerton, CA 92832 (714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
REPLACEMENT PARTS FOR
THE CLEAN OUT PLUG WRENCH SET
WITH REVERSING RATCHET WRENCH
1701-RHW #1 Raised Head: 7/8” ID 1701-CSW #6 Countersunk: 3/4” SQ
1701-RHW #2 Raised Head: 1-1/16” ID 1701-CSW #7 Countersunk: 7/8” SQ
1701-RHW #3 Raised Head: 1-1/4” ID 1701-CSW #8 Countersunk: 1-1/8” SQ
1701-RHW #4 Raised Head: 1-3/4” ID 1701-RHW #1 Countersunk: 1-1/4” SQ
1701-RHW #5 Raised Head: 2-1/8” ID 1701-SSW #10 Slotted” 1/4”x 1”
1701-BX 19-3/4” x 6” x 4” BOX 1701-SSW #11 Slotted: 1/4” x 1-3/4”
1701-RAT12 Reversing Ratchet Wrench 7000-3450 3/4"x 1/2" Adapter
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
CLEAN OUT PLUG WRENCH SETS
ALSO AVAILABLE WITHOUT ACARRYING CASE
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@ perfectoproducts.net
VALVE OPERATOR KEY SET Part No. 1600-VO
OPEN AND CLOSE YOUR UTILITY VALVESWITH THIS MULTI-FUNCTION KIT
This set includes valve operator keys for manysized valves:
2" Square Head 1-3/4" Square Head1-1/2" Square Head 1-1/4" Square Head1" Square Head
All sizes smaller than 2" nest inside the 2" operatorand bolt in for extra strength. Plus a 7/8" slottedkey and a 2-prong head for small valve handles
Two 28" extensions and a sliding T-Handle makefor easy operation. All come packaged in a 29" x 6" x 3" metal box.
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
SPUD NUT WRENCHES
INSTALL AND REMOVE CLOSET AND URINAL SPUDS WITH THESEHANDY, DURABLE WRENCHES. SLOTS IN THE TOOL LINE UP ANDGRIP FIRMLY TO THE RAISED RIDGES. THE FULL TOOLKIT (7000-SNW) HAS A 3/4" x 1/2" SOCKET ADAPTOR FOR YOUR 1/2"RATCHET WRENCH.
PART NUMBERS:
3/4" 7000-SNW-34 1-1/4" 7000-SNW-1141-1/2" 7000-SNW-112 2" 7000-SNW-2
ALL 4 WRENCHES IN A CARRYING CASE 7000-SNW
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
WATER METER and CITY METER KEYS
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
Make a quick connection from anexisting iron body clean out to ABSpipe without bushings or maleadaptors! Just remove the threadedplug, and screw in the NST to ABSadaptor. Then just couple up thepipe. Simple, inexpensive,efficient.
NST to IPS ADAPTORFor Connecting ABS Pipe To An Existing Clean Out
3-1/2" NST to 3" IPS Part No. 7000-ABS 2-1/2" NST to 2" IPS Part No. 7000-ABS2
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
SLOAN TAILPIECE TOOLSTURDY WELDED STEEL CONSTRUCTION
SLOTTED END FITS INTO THE SLOAN TAILPIECE, CATCHES THE RAISED RIDGES, AND ALLOWS
YOU TO UNSCREW THE TAILPIECE WITHOUT DAMAGING THE CHROME FINISH
3/4" SQUARE HOLE ADAPTS TO THE PERFECTO RIGHT ANGLE
WRENCH.
- - - - - OR - - - - -
PUT A CRESCENT WRENCH ON THE SQUARE END.
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
FAUCET NUT SAWPart No. 7000-NS
GRIND THROUGH FAUCET NUTS IN SECONDS WITHTHIS CARBIDE SAW IN YOUR DRILL.
SAFETY FIRST:WEAR GLASSES
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
EMERGENCY GAS SHUT-OFF WRENCH
Part Number 7000-EW
In an emergency, such as an earthquake,don’t fumble in the dark when you suspect that there’s a gas leak in the house.Leave this sturdy tool right next to thegas meter so its there when you need it.
Sturdy steel construction
1/2" slotted to fit household gas meters
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
A-964 SPEED TYPE TAILPIECEFLANGING TOOL
MAKES 1-1/4" or 1-1/2" TAILPIECES FROM YOUR SCRAPTUBING (One tool for each size)
Capacity: 1-1/2" OD Tubing 17 to 20 gauge
NO POUNDING OR HAMMERING
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: perfectoproducts@juno.com
A-964 FLANGING TOOL
OPERATING INSTRUCTIONS:
1. Turn the black handle on the flanging tool until the ball in the head of the flanging tool is allthe way into the head.
2. Put the brass tubing to be flanged over the knurled end of the tool until it is right against thelip of the tool where the ball shows
3. Put the brass tubing (with the tool inside) into a pipe vise. Tighten the vise down so that itholds both the brass tube and the knurled part of the handle.
4. Turn the handle clockwise once around so that the ball begins to flare the tubing.5. Twist the handle slightly, so that the ball moves out from the head.6. Repeat steps 4 and 5 until the ball has moved all the way out, and the brass tubing has a good
flange on it.
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
STUVEL FLUSH VALVE RESEATER TOOL■ CUTS WATER BILLS ■ STOPS COSTLY FLUSH VALVE LEAKS
Every plumber should have this handy tool, invented by a plumber. Use theStuvel Reseater Tool and move on to more profitable jobs. A few turns of thewrist reseats the roughest valve seat in perfect alignment with the pull-wireguide. Lime and corrosion – which are the cause of the leaks – are removed in asnap!
1) Remove flush ball and wire.2) Insert sliding pin in the guide.3) Exerting downward pressure, twist tool back
and forth until the valve seat is smooth.4) The grinding ball does the work. It resurfaces
any size flush valve seat.
221 W. Santa Fe Ave,. Fullerton, CA 92832 ! (714-870-9881) C FAX (714-870-6399)website: www.perfectoproducts.net C E-MAIL: sales@perfectoproducts.net
PERFECTO TILE PROBES
Part No: 1800-4T, 1800-5T, 1800-6T(Always use safety gloves to prevent electrocution)
221 W. Santa Fe Avenue, Fullerton, CA 92832(714-870-9881) ∙ FAX (714-870-6399) ∙ E-MAIL: sales@perfectoproducts.net
BAND-AID PIPE CLAMPPart No. 7000-BAPC
For those quick-fixes until the repair can be made. The water pressure can stay on 3” clamp fits up to 2” pipe Heavy duty worm gear for a secure clamp 1” Square rubber seat covers most leaks Re-Usable
221 W. Santa Fe Ave,. Fullerton, CA 92832(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
OUTSIDE EASY OUTPart No. 7000-EO
Tighten the bolts down and turn with a water meter key
PERFECTO WASHERTRIMMERPart No. 7000-WT
FLOOR DRAIN WRENCHPart No. 7000-DW
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
This simple tool is a mustwhen the floor draincompression ring isjammed tight! Forgetscrewdrivers, chisels, orpry bars. Forget wastingtime trying to figure outwhat tool to use.
This sturdy tool is madefrom 3/8" steel plate, flamecut to fit exactly into thegrooves in the inner ring.
Just drop the drain wrenchinto place and insert a 3/8"square ratchet wrench(you’ll probably need anextension) and twist thatdrain ring out in seconds.
Don’t waste your time onsimple tasks, when there’sa simple tool to deal withit.
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
THE SINKLEAR TOOLfrom PLUMB E-Z, Inc.
Use this simple, unique tool to install a garbage disposal single-handed,and in less time. Simply lower the tool through the sink flange (alreadyinstalled) into the mouth of the disposal, then hoist the disposal intoplace. Slip the slotted plate onto the threaded shaft on the sink side,and the disposal will stay in place. Reach under the sink, turn the lockring, and you’re done. Comes in it’s own carrying case.
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
THE IN-SINK INSTALLERfrom Plumb-E-Z, Inc.
(Perfecto Part No. 6000-IN)
Install the flange for a garbage disposal with ease! Just putty upthe flange, assemble the parts on the IN-SINK INSTALLER, snug upthe top clamp on the threaded rod and then snap the ring off thecup with a screwdriver. That’s it! (Full installation instructionsincluded.)
221 W . Santa Fe Ave,. Fullerton, CA 92832
(714-870-9881) C FAX (714-870-6399) C E-MAIL: sales@perfectoproducts.net
IMPORTANT FEATURES:
• A TW O OR THREE HOUR JOB CAN BE DONE IN 15 OR
20 MINUTES.
• NO DISCONNECTING OF PLUMBING NECESSARY.
• W ILL NOT CROSS TEES OR GO UP VENT
• EXCLUSIVE PATENTED CRAWL HEAD
• EASY TO TIGHTEN SET SCREW
• POSITIVE LOCK CABLE
• A PERFECTLY BALANCED CONTAINER
DRAIN CLEANERSNO MORE REMOVING TRAPS TO CLEAN DRAINS!
Your supplier for all Quality Erickson Products is:
Recommended