EMC Parts Manual - HILLARY MACHINERY · fadal emc parts manual september 2003 3 sheet metal...

Fadal EMC Parts Manual

TABLE OF CONTENTS

PartsManualEMC MODEL

SHEET METAL ASSEMBLY .................................................................................................................................................3SHEET METAL ASSEMBLY B.O.M. ....................................................................................................................................4BASE ASSEMBLY ................................................................................................................................................................5COLUMN ASSEMBLY ..........................................................................................................................................................6SADDLE ASSEMBLY ...........................................................................................................................................................7TABLE ASSEMBLY ..............................................................................................................................................................8CARRIAGE ASSEMBLY .......................................................................................................................................................9ATC ASSEMBLY ..................................................................................................................................................................10ATC TURRET ASSEMBLY ...................................................................................................................................................11GEAR MOTOR ASSEMBLY .................................................................................................................................................12WHEEL GENEVA ASSEMBLY ..............................................................................................................................................13WHEEL GENEVA ASSEMBLY B.O.M. .................................................................................................................................14Y AXIS BALLSCREW ASSEMBLY .......................................................................................................................................15Y AXIS BALLSCREW ASSEMBLY B.O.M. ...........................................................................................................................16Z AXIS BALLSCREW ASSEMBLY .......................................................................................................................................17Z AXIS BALLSCREW ASSEMBLY B.O.M. ...........................................................................................................................18X AXIS BALLSCREW ASSEMBLY .......................................................................................................................................19X AXIS BALLSCREW ASSEMBLY B.O.M. ...........................................................................................................................20HEAD ASSEMBLY ...............................................................................................................................................................21DRAWBAR CYLINDER ASSEMBLY ....................................................................................................................................22DRAWBAR CYLINDER ASSEMBLY B.O.M. ........................................................................................................................23SPINDLE MOTOR ASSEMBLY ............................................................................................................................................24SPINDLE ASSEMBLY ..........................................................................................................................................................25HEAD COVER ASSEMBLY ..................................................................................................................................................26TRANSFORMER CABINET ASSEMBLY ..............................................................................................................................27TRANSFORMER ASSEMBLY ..............................................................................................................................................28CNC CONTROL BOX ASSEMBLY .......................................................................................................................................29CNC CONTROL BOX ASSEMBLY B.O.M. ...........................................................................................................................30AXIS COVER ASSEMBLY ....................................................................................................................................................31AXIS COVER ASSEMBLY B.O.M. .......................................................................................................................................32PENDANT ASSEMBLY ........................................................................................................................................................33

SEPTEMBER 2003 I

II SEPTEMBER 2003

This reference covers the following Fadal products:

Model EMC

Corporate Office . . . . . . . . . . . . . . . . . . . . . . .voice (818) 407-1400 . . . . . . . . . . . . . . . . . . . . fax (818) 407-0020Service / Parts . . . . . . . . . . . . . . . . . . . . . . . . .voice (818) 727-2100 . . . . . . . . . . . . . . . . . . . . fax (818) 407-1004Programming Support . . . . . . . . . . . . . . . . . .voice (818) 727-2100 . . . . . . . . . . . . . . . . . . . . fax (818) 407-0061

support@fadal.com20701 Plummer Street Chatsworth California 91311 U.S.A.

The content of this manual has been reviewed for accuracy and is applicable to current Fadal hardware and software products as described herein. Differences may exist and we cannot guarantee that they are completely covered in this document. The information in this document is reviewed regularly and any necessary changes will be incorporated in the next revision. We welcome any suggestions for improvement.

Material is subject to change without notice.

This manual is for the exclusive use of Fadal Customers and Distributors. The reproduction, transmission or use of this document or its contents is not permitted without the expressed written permission of Fadal Machining Cen-ters. All rights, including rights created by patent grant or registration of a utility, model or design, are reserved.

SEPTEMBER 2003 1

This page intentionally left blank.

SEPTEMBER 2003 2

EMC Parts ManualFadal

SHEET METAL ASSEMBLY

SEPTEMBER 2003 3

SHEET METAL ASSEMBLY

4 SEPTEMBER 2003

BASE ASSEMBLY

SEPTEMBER 2003 5

COLUMN ASSEMBLY

6 SEPTEMBER 2003

SADDLE ASSEMBLY

SEPTEMBER 2003 7

TABLE ASSEMBLY

8 SEPTEMBER 2003

CARRIAGE ASSEMBLY

SEPTEMBER 2003 9

ATC ASSEMBLY

10 SEPTEMBER 2003

ATC TURRET ASSEMBLY

SEPTEMBER 2003 11

GEAR MOTOR ASSEMBLY

12 SEPTEMBER 2003

WHEEL GENEVA ASSEMBLY

SEPTEMBER 2003 13

WHEEL GENEVA ASSEMBLY

14 SEPTEMBER 2003

Y AXIS BALLSCREW ASSEMBLY

SEPTEMBER 2003 15

Y AXIS BALLSCREW ASSEMBLY

16 SEPTEMBER 2003

Z AXIS BALLSCREW ASSEMBLY

SEPTEMBER 2003 17

Z AXIS BALLSCREW ASSEMBLY

18 SEPTEMBER 2003

X AXIS BALLSCREW SUPPORT

SEPTEMBER 2003 19

X AXIS BALLSCREW ASSEMBLY

20 SEPTEMBER 2003

HEAD ASSEMBLY

SEPTEMBER 2003 21

DRAWBAR CYLINDER ASSEMBLY

22 SEPTEMBER 2003

DRAWBAR CYLINDER ASSEMBLY

SEPTEMBER 2003 23

SPINDLE MOTOR ASSEMBLY

24 SEPTEMBER 2003

SPINDLE ASSEMBLY

SEPTEMBER 2003 25

HEAD COVER ASSEMBLY

26 SEPTEMBER 2003

TRANSFORMER CABINET ASSEMBLY

SEPTEMBER 2003 27

TRANSFORMER ASSEMBLY

28 SEPTEMBER 2003

CNC CONTROL BOX ASSEMBLY

SEPTEMBER 2003 29

CNC CONTROL BOX ASSEMBLY

30 SEPTEMBER 2003

AXIS COVERS ASSEMBLY

SEPTEMBER 2003 31

AXIS COVERS ASSEMBLY

32 SEPTEMBER 2003

PENDANT ASSEMBLY

SEPTEMBER 2003 33

EMC Parts Manual - HILLARY MACHINERY · fadal emc parts manual september 2003 3 sheet metal...

Documents

One-Dimensional Metal Nanowire Assembly via Block

with Double Doors and Metal Roof Assembly Manual

EMC NetWorker Module for Microsoft for Windows Bare Metal ... · EMC® NetWorker® Module for Microsoft for Windows Bare Metal Recovery Solution Version 9.0.1 User Guide 302-002-939

Metal Chalcogenide Nanocrystal Assembly: From Synthesis To

Metal bellows couplings - EMC TECHNOLOGY CENTER€¦ · Typical characteristics of metal bellows couplings ... Application of a metal bellows coupling in a machine tool drive Drive

Cooperative colloidal self-assembly of metal-protein superlattice … · ARTICLE Cooperative colloidal self-assembly of metal-protein superlattice wires Ville Liljeström1,2, Ari

Self-assembly of polyhedral metal-organic framework ...€¦ · Self-assembly of polyhedral metal–organic framework particles into three-dimensional ordered superstructures Civan

Control of metal-directed self-assembly by metal-amine interactions · 2011-01-19 · Control of metal-directed self-assembly by metal-amine interactions ... followed by slow addition

Precision Metal Forming and Assembly for the North ... · PDF filePrecision Metal Forming and Assembly for the North American Manufacturing Industry. ... manufacturers and leading

REQUEST FOR QUOTATION - gailebank.gail.co.in · MODEL: EMC-22 Motor Checker EMC-22 of EMC Electronik Make, Metal Body, Heavy duty, Industrial type Six step of range Selection with

Direct Assembly and Metal-Ion Binding Properties of ... · Direct Assembly and Metal-Ion Binding Properties of Oxytocin Monolayer on Gold Surfaces Evgeniy Mervinetsky,†,‡ Israel

Version #1.8 Metal Roof Assembly Manual

Assembly Instructions & User’s Manual Discovery 9 Metal

Assembly & Safety Manual - Texas Metal Buildings

Post-Assembly Atomic Layer Deposition of Ultrathin Metal

Assembly & Safety Manual - Texas Metal Buildings · Assembly & Safety Manual. ... Texas Metal Buildings structural steel plans and plans for ... engineer of record or design professional

Design and self-assembly of metal-organic framework

Mr Fothergill’s Metal Hook Stand and POS Assembly ... · Mr Fothergill’s Metal Hook Stand and POS Assembly Instructions Stand components • Foot • Bottom section • Top section

HMI Elevator Manual Model 66-42 - Honeyville Metal Metal, Inc. Bucket Elevator Model 66-42 Assembly & Service Manual 4 V. Suggestions For Assembly Assembly bolts and nuts are supplied

Sheet metal assembly verification by fea methods