View
0
Download
0
Category
Preview:
Citation preview
© Supercars – 2020 Division “G” i ISSUED JANUARY 2020
SUPERCARS OPERATIONS MANUAL 2020
DIVISION “G” – DS2 TECHNICAL RULES CONTENTS
Rule. Title Page
G1. GENERAL ............................................................................................................................. 1 G1.1 Preamble ................................................................................................................ 1 G1.2 Model Eligibility and VSD’s ..................................................................................... 1 G1.3 CTM Overriding Authority ....................................................................................... 1
G2. COMPLIANCE ....................................................................................................................... 2 G2.1 General ................................................................................................................... 2 G2.2 Examination for Eligibility ........................................................................................ 2
G2.3 Disputes .................................................................................................................. 3 G2.4 Minor Non-Compliance ........................................................................................... 3 G2.5 Repairs ................................................................................................................... 3
G3. SCRUTINEERING ................................................................................................................. 4 G3.1 Targeted Scrutiny ................................................................................................... 4 G3.2 Onus on Competitor ................................................................................................ 4
G3.3 Location of Targeted Scrutiny ................................................................................. 4 G3.4 Equipment to be Scrutineered ................................................................................ 4
G3.5 Additional Scrutineering .......................................................................................... 4 G3.6 Changes/Modifications to Cars ............................................................................... 5 G3.7 Prohibition of unsafe Cars ...................................................................................... 5
G3.8 On Track Incidents .................................................................................................. 5 G3.9 No Replacement Cars ............................................................................................ 5
G3.10 Prohibited Work ...................................................................................................... 5 G3.11 Accidents and Scrutineering ................................................................................... 5
G4. CONSTRUCTION & MODIFICATION ................................................................................... 6 G4.1 Minimum Weight ..................................................................................................... 6
G4.2 Ballast ..................................................................................................................... 6 G4.3 Freedoms Permitted ............................................................................................... 7 G4.4 Additional Accessories ............................................................................................ 8
G4.5 Composite Components ......................................................................................... 8 G4.6 Exotic Materials ...................................................................................................... 8
G4.7 Manufacturing and Measuring Tolerances .............................................................. 9 G4.8 Vehicle Datums ....................................................................................................... 9
G5. SAFETY EQUIPMENT ........................................................................................................ 10
G5.1 Seats .................................................................................................................... 10 G5.2 Leg Brace ............................................................................................................. 10 G5.3 Safety Harness ..................................................................................................... 10 G5.4 Window/Racing Nets ............................................................................................ 10
G5.5 Roll Over Protection Structure “ROPS” ................................................................. 11 G5.6 Fire Extinguisher Systems .................................................................................... 11 G5.7 Tethers ................................................................................................................. 11
G6. BODY REQUIREMENTS .................................................................................................... 12
© Supercars – 2020 Division “G” ii ISSUED JANUARY 2020
Rule. Title Page
G6.1 Bodywork .............................................................................................................. 12 G6.2 Front Bumper Bar Air Intakes ............................................................................... 13 G6.3 Windscreens ......................................................................................................... 13 G6.4 Doors .................................................................................................................... 13
G6.5 Rear Vision Mirrors ............................................................................................... 14 G6.6 Tow Hooks and Vehicle Recovery ........................................................................ 14 G6.7 Accessories .......................................................................................................... 15 G6.8 Aerodynamics ....................................................................................................... 15 G6.9 Roof Duct .............................................................................................................. 15
G7. SUSPENSION ..................................................................................................................... 16 G7.1 Springing Medium ................................................................................................. 16 G7.2 Front Suspension .................................................................................................. 16 G7.3 Front Upright ......................................................................................................... 17
G7.4 Rear Suspension .................................................................................................. 17 G7.5 Rear Spindle ......................................................................................................... 17 G7.6 Anti-Roll Bars ........................................................................................................ 18
G7.7 Suspension Adjustment ........................................................................................ 18 G7.8 Dampers ............................................................................................................... 19
G8. ENGINE ............................................................................................................................... 20 G8.1 General ................................................................................................................. 20
G8.2 Other Engine Components ................................................................................... 20 G8.3 Cooling System ..................................................................................................... 20 G8.4 Exhaust System .................................................................................................... 21
G8.5 Inlet System .......................................................................................................... 21 G8.6 Engine Mounting ................................................................................................... 22
G8.7 Engine Weight ...................................................................................................... 22 G8.8 Flywheel ............................................................................................................... 22
G8.9 Clutch ................................................................................................................... 22
G9. FUEL SYSTEM .................................................................................................................... 23
G9.1 Fuel Tank Requirements - General ....................................................................... 23 G9.2 Fuel Pressure ....................................................................................................... 24 G9.3 Fuel Lines ............................................................................................................. 24
G9.4 Capacity ................................................................................................................ 24 G9.5 Fuel Tank Vent ..................................................................................................... 24
G9.6 Fuel Fillers ............................................................................................................ 24
G10. DRIVETRAIN ................................................................................................................ 25 G10.1 General ................................................................................................................. 25
G10.2 Transaxle .............................................................................................................. 25 G10.3 Gear Lever ............................................................................................................ 25 G10.4 Drop Gear Ratios .................................................................................................. 26 G10.5 Transaxle Cooling ................................................................................................. 26
G10.6 Gear Shift Cut ....................................................................................................... 26 G10.7 Tailshaft Hoops ..................................................................................................... 26
G11. BRAKES ........................................................................................................................ 27 G11.1 General ................................................................................................................. 27 G11.2 Pedal Box ............................................................................................................. 27
© Supercars – 2020 Division “G” iii ISSUED JANUARY 2020
Rule. Title Page
G11.3 Brake Pads ........................................................................................................... 28 G11.4 Other Brake System Requirements ...................................................................... 28 G11.5 Brake Ducting ....................................................................................................... 28
G12. STEERING .................................................................................................................... 29
G12.1 General ................................................................................................................. 29
G13. WHEELS ....................................................................................................................... 30 G13.1 Control Wheel ....................................................................................................... 30 G13.2 Centre Lock Spindles and Wheel Nuts ................................................................. 30 G13.3 Wheel Coatings .................................................................................................... 30
G14. ELECTRICAL SYSTEM ................................................................................................ 31 G14.1 General ................................................................................................................. 31
G14.2 Master Isolation Switch ......................................................................................... 31 G14.3 Battery .................................................................................................................. 31 G14.4 Alternator .............................................................................................................. 32 G14.5 Lights .................................................................................................................... 32
G14.6 Starter Motor ......................................................................................................... 32 G14.7 Fuel Pump Power Supply ..................................................................................... 32 G14.8 Identification Lights ............................................................................................... 32
G14.9 In Car Camera System ......................................................................................... 33
G15. ECU & DATA SYSTEMS ............................................................................................... 34
G15.1 Control Electrical Package .................................................................................... 34 G15.2 Engine Control ...................................................................................................... 35 G15.3 Control Actuators and Sensors ............................................................................. 35
G15.4 Pit Lane Speed Limiter ......................................................................................... 36
G15.5 Rain Light/Stall Light ............................................................................................. 36 G15.6 Electronic Data – Logging, Display & Telemetry ................................................... 36 G15.7 Signals to/from Cars ............................................................................................. 36
G16. CAR EQUIPMENT ........................................................................................................ 37 G16.1 Airjack ................................................................................................................... 37
SCHEDULE G1. CONTROL PARTS .......................................................................................... 38 1. Chassis ............................................................................................................................ 38 2. Suspension and Steering................................................................................................. 38
3. Transaxle and Drivetrain ................................................................................................. 39 4. Wheels and Tyres ............................................................................................................ 40
5. Brake System .................................................................................................................. 40 6. Fuel System ..................................................................................................................... 41
7. Electrical System ............................................................................................................. 42 8. Sensors and Actuators .................................................................................................... 43 9. Bodywork and General .................................................................................................... 46 10. Composites Components .............................................................................................. 46
SCHEDULE G2. CONTROL WHEEL NUT................................................................................. 47
SCHEDULE G3. SIDE IMPACT PROTECTION STRUCTURE .................................................. 48
SCHEDULE G4. DRIVER DOOR SKIN LAYUP ......................................................................... 49
© Supercars – 2020 Division “G” iv ISSUED JANUARY 2020
Rule. Title Page
SCHEDULE G5. FRONT GUARD, LEFT FRONT DOOR SKIN, REAR DOOR SKIN LAYUP ... 50
SCHEDULE G6. REAR QUARTER PANEL LAYUP .................................................................. 51
SCHEDULE G7. FRONT DOOR WINDOW ............................................................................... 52
SCHEDULE G8. LEG BRACE APPROVED MATERIAL LIST ................................................... 53
SCHEDULE G9. ENGINE LOG EXAMPLE ................................................................................ 54
© Supercars – 2020 Division “G” Page G1 of G54 ISSUED JANUARY 2020
SUPERCARS OPERATIONS MANUAL 2020
DIVISION “G” – DS2 TECHNICAL RULES G1. GENERAL
G1.1 Preamble
1.1.1 This Division G applies only to the DS2.
1.1.2 A Car must remain identical in all respects to the particular model of Car as defined in the
relevant VSD and must be constructed in accordance with the Design supplied by
Supercars for the Car except for the freedoms allowed, and to the extent permitted, by the
Rules.
1.1.3 Any modification that is not in keeping with the spirit and intent of the Rules is not permitted
and where necessary shall be banned without notice by Supercars.
1.1.4 In all circumstances the primary function of any component, even if all or part of its Design
is free, is the overriding factor in determining its compliance with the Rules. Any secondary
function/s, unless specifically permitted by the Rules, are not permitted.
1.1.5 No part of a Car may be modified and/or deleted and/or added to unless permitted by the
Rules.
1.1.6 For clarification, in these Rules, unless it says that you can, then you cannot.
G1.2 Model Eligibility and VSD’s
1.2.1 Only the makes and models of Cars, as detailed in the table below and for which a VSD is
available, are eligible for Competition:
Eligible makes and models of Cars
VSD
Year Ford Holden Nissan Mercedes-Benz Volvo
2015 Falcon FG-X VF Commodore Altima L33 E63 AMG W212 S60
2016 Falcon FG-X VF Commodore Altima L33 S60
2017 Falcon FG-X VF Commodore Altima L33
1.2.2 Supercars reserves the right to add and/or remove makes and models of Cars to the above
table.
G1.3 CTM Overriding Authority
1.3.1 Traction control is prohibited. 1.3.1.1 The CTM in his sole discretion, which will not be subject to any protest or appeal,
has the right to deem any form of program, device, system, component(s), mechanism(s) as traction control.
1.3.2 Aerodynamic enhancement is prohibited. 1.3.2.1 The CTM in his sole discretion, which will not be subject to any protest or appeal,
has the right to deem any form of program, device, system, component(s), mechanism(s) as an aerodynamic enhancement.
1.3.3 Fuel trimming during a race is prohibited. 1.3.3.1 The CTM in his sole discretion, which will not be subject to any protest or appeal,
has the right to deem any form of program, device, system, component(s), mechanism(s) that aid the Driver in adjusting or trimming the air fuel mixture during a race as fuel trimming.
© Supercars – 2020 Division “G” Page G2 of G54 ISSUED JANUARY 2020
G2. COMPLIANCE
G2.1 General
2.1.1 A Car must comply with the Design, relevant VSD, ESD and the Rules.
2.1.2 A Car must be constructed in accordance with the Design and comply with all aspects of
the relevant VSD, ESD and the requirements of the Rules.
2.1.3 A Car must comply with the relevant sections of Article 277 of Appendix J Category II SH
to the ISC of the FIA.
2.1.4 All Control Parts are listed in Schedule G1 and must always comply with the definition of a
Control Part.
2.1.5 Each Competitor is responsible for ensuring that their Car complies with the conditions of
eligibility contained in the Rules throughout each Event and all Supercars authorised
activities including all rides and at a Supercars Test.
2.1.6 The acceptance of the targeted scrutiny declaration conditions will be deemed to be an
implicit statement by the Competitor of conformity with the Rules.
G2.2 Examination for Eligibility
2.2.1 Should the CTM suspect at any time that a Car does not comply with the Rules, the
Competitor, or Authorised Representative, must be so advised and given the opportunity to
comment on the suspected or alleged ineligibility.
2.2.2 Any comment so made may be recorded by the CTM, and subsequently may be presented
at any Stewards’ Hearing.
2.2.3 Should the CTM fail to receive an adequate comment on the suspected or alleged
ineligibility, which the CTM alone has sole discretion to consider as adequate or satisfactory,
the CTM may require the Car to be impounded and examined, including such dismantling
as may be necessary, to determine the points of eligibility in question.
2.2.4 At the direction of the Stewards, any components or parts of a Car may be sealed by the
CTM for examination by the CTM.
2.2.4.1 For any item sealed and/or identified by any means by the CTM, it is the
Competitors responsibility to ensure the item, which may include removable
part/s, complies with all conditions of eligibility contained in the Rules.
2.2.4.2 With a view to facilitate scrutineering at the Race Track, each Team is required
to:
Have available sufficient sets of long damper mounting bolts that have been
drilled to facilitate the passage of 1.5mm diameter lock wire.
Ensure that the transaxle can be lock wired at the sandwich plate and the
two (2) side covers.
© Supercars – 2020 Division “G” Page G3 of G54 ISSUED JANUARY 2020
G2.3 Disputes
2.3.1 In the case of a dispute about a Car’s compliance with any of the provisions of the Rules,
such dispute will be referred to the Stewards by the RD or DRD for determination.
2.3.2 The Stewards will conduct a Hearing into the issue and may make any decision thereon.
2.3.3 If, during any such Hearing, the Stewards determine that the matter is of a technically
complex nature the Stewards:
2.3.3.1 will refer only the technical issue to the CTM for a determination; and/or
2.3.3.2 may adjourn the Hearing until the determination of the CTM is received; and
2.3.3.3 subsequently resume and complete the Hearing and make a decision taking into
account the determination of the CTM.
2.3.4 The determination of the CTM will be unconditionally binding on any Stewards’ Hearing in
regard to that issue.
G2.4 Minor Non-Compliance
2.4.1 The CTM, having noted an area of minor non-compliance, may endorse the Car’s
Motorsport Australia log book with an entry regarding rectification of the non-compliance.
2.4.2 Having so endorsed the Car’s Motorsport Australia log book, before the Car is permitted on
to the Circuit, the CTM must send to the Stewards the Car’s Motorsport Australia log book
and a note in the following form:
2.4.2.1 "In my view, the minor non-compliance noted in the log book of this Car does not
improve the performance to such an extent that the Car should be excluded from
this Event, and thus it may compete in this condition for this Event only."
2.4.3 Upon receipt of the note referred to in Rule G2.4.2, the Stewards may then permit the Car
to participate in the Event subject to the endorsement being countersigned by the Stewards
in the Car’s Motorsport Australia log book.
2.4.4 If the Stewards have specifically approved the participation of a Car notwithstanding an
endorsement in its Motorsport Australia log book pursuant to Rule G2.4.1, then no protest
or appeal on that ground by any other person will be accepted in respect of that Event.
2.4.5 Where a question of eligibility is raised during or after Competition and that matter would
have been treated as a “minor ineligibility” if raised at scrutiny the Stewards may treat the
matter post event in the manner as determined above.
G2.5 Repairs
2.5.1 Any repairs or replacements must take full account of engineering integrity and safety.
2.5.2 The CTM has the right to consider the engineering integrity and safety of any modifications
carried out and to require corrective action if appropriate.
2.5.3 Restoration of Bodywork and Chassis geometry following accidental damage is permitted
only using approved panels and parts or by the addition of materials necessary to affect the
repairs (e.g.: body filler, weld metal).
2.5.4 Any repairs to the Chassis must respect the Design.
© Supercars – 2020 Division “G” Page G4 of G54 ISSUED JANUARY 2020
G3. SCRUTINEERING
G3.1 Targeted Scrutiny
3.1.1 In Australia, each Car will be subject to the provisions of the targeted scrutiny program for
each Event. The targeted scrutiny program is an ongoing program which is based on a
combination of routine and random audits of Cars and Driver’s apparel to ensure that all
equipment remains in compliance with the Rules. Routine audits will be conducted on a Car
every 12 months or at every 4th Event, whichever comes first.
3.1.2 Outside Australia other requirements may apply in which case the details will be included
in the Supplementary Regulations.
G3.2 Onus on Competitor
3.2.1 The onus is on the Competitor to ensure full compliance with all provisions of the targeted scrutiny program as follows: 3.2.1.1 by signing the Entry Registration Form and the Authorised Representatives
Briefing attendance sheet for an Event, the Authorised Representative of a Car presented at an Event agrees to abide by the conditions described in the “Declaration of Conformity”.
3.2.1.2 each Car that is selected for an audit at an Event under the targeted scrutiny program must be presented in a complete and finished state at the time advised by the CTM.
3.2.1.3 Driver’s apparel will be subject to random audits throughout the Event and must be made available for inspection at any time as requested by the CTM.
G3.3 Location of Targeted Scrutiny
3.3.1 Targeted scrutiny audits will be carried out at each Competitor’s assigned Pit Garage or other area as determined by the CTM.
G3.4 Equipment to be Scrutineered
3.4.1 In addition to the audits carried out under the targeted scrutiny program, the following equipment must also be presented to the CTM for inspection and approval at each Event: 3.4.1.1 all Driver’s equipment including but not limited to: helmet, FHR device, overalls,
underwear, balaclava, gloves, shoes, two (2) x 9 Kg fire extinguishers, pressure vessel certification; and,
3.4.1.2 for Events requiring refuelling during a race, all pit crew apparel and refuelling towers (including all components thereof).
G3.5 Additional Scrutineering
3.5.1 The CTM has unfettered discretion to carry out or require additional scrutineering. 3.5.2 The CTM may at any time:
3.5.2.1 check the eligibility of a Car; 3.5.2.2 require a Car to be sealed and/or dismantled to ensure that the conditions of
eligibility and/or safety are fully satisfied; 3.5.2.3 require a Competitor to supply to the CTM or the Stewards such parts or samples
as may be specified by the CTM; and 3.5.2.4 require that any components or parts of a Car be sealed for examination by the
Stewards or by the CTM.
© Supercars – 2020 Division “G” Page G5 of G54 ISSUED JANUARY 2020
G3.6 Changes/Modifications to Cars
3.6.1 If at any time after the commencement of an Event, a Car has been dismantled or modified
in any way which may affect the safety of the Car or which raises any question about its
eligibility, or which is involved in an Incident which has similar results, it must be re-
presented to the CTM for scrutineering approval prior to being permitted back on the Circuit.
G3.7 Prohibition of unsafe Cars
3.7.1 Any Car may be prohibited by the CTM from participating in any Competition for safety
reasons.
G3.8 On Track Incidents
3.8.1 The RD or the CTM may require any Car involved in an Incident to be stopped at its Pit Bay
to be further examined and checked.
G3.9 No Replacement Cars
3.9.1 Replacement Cars are not permitted after the commencement of an Event.
G3.10 Prohibited Work
3.10.1 During any race, it is forbidden to change cylinder blocks (crankshaft case and cylinders)
or the Chassis, under Penalty of exclusion.
G3.11 Accidents and Scrutineering
3.11.1 Damage incurred by a Car during any Competition may render it liable to being shown the
black flag with orange disc and consequently requiring an immediate return to the Pit Lane
for examination by the CTM.
3.11.2 Following any necessary rectification and subsequent to a satisfactory examination by the
CTM, the Car may re-join the Circuit at the discretion of the RD.
3.11.3 A Car withdrawn from any Competition due to accident damage must be inspected by the
CTM before it is permitted to continue to participate in the Event.
© Supercars – 2020 Division “G” Page G6 of G54 ISSUED JANUARY 2020
G4. CONSTRUCTION & MODIFICATION
G4.1 Minimum Weight
4.1.1 The minimum weight of a Car is 1410 kg and will include the weight of the Driver wearing
their complete Driver’s apparel, either as recorded by the CTM at the Driver’s first Event for
the year, or with the Driver on board.
4.1.2 For any Event in which Co-Drivers are permitted the following will apply:
4.1.2.1 For all Sessions the minimum weight applies only to the Primary Driver.
4.1.3 The minimum front axle weight of a Car is 755kg, and will be measured as follows:
4.1.3.1 at the front axle centreline; and
4.1.3.2 with the Driver wearing their complete Driver’s apparel on board; or
4.1.3.3 with weights placed in the seat to replicate the Driver’s recorded weight.
4.1.4 The minimum weights stated in Rules G4.1.1, G4.1.2 and G4.1.3 must be achieved both
during and immediately after any Competition at an Event, with the exception that during
any Competition in which refuelling is permitted, the minimum weights must be achieved
without fuel.
4.1.5 Supercars reserve the right at all times to amend the weights of Cars in the interests of
equitable Competition.
G4.2 Ballast 4.2.1 It is permitted to complete the weight of a Car by one or several units of ballast provided
that each unit: 4.2.1.1 is a strong and unitary block; and 4.2.1.2 is fixed by means of tools; and 4.2.1.3 has the ability to affix scrutineering seals; and 4.2.1.4 must be attached to the Chassis via 8.8 class bolts; and 4.2.1.5 has a minimum diameter of 8mm for each fixing point; and 4.2.1.6 must have at least two (2) fixing points; and 4.2.1.7 must not weigh more than 10 kg; and 4.2.1.8 must be fitted within the Car’s cockpit with the exception that ballast may be
added to removable components that have a specified minimum weight only to ensure compliance with the minimum weight specified of that component; and
4.2.1.9 is made of a material which has a maximum relative density of twelve (12). 4.2.2 The minimum Driver mass is 103.5kg which will include the following:
4.2.2.1 Driver’s weight with his complete apparel recorded by the CTM at the Driver’s first Event for the Season; and
4.2.2.2 the seat, seat brackets, seat insert and all mounting bolts, nuts, washers and spacers; and
4.2.2.3 any additional ballast, which will be considered Driver ballast; and 4.2.2.4 The leg brace and all mounting bolts, nuts, washers and spacers.
4.2.3 Driver ballast must be carried in an area bounded by the following dimensions: 4.2.3.1 X=575mm, X=1985mm and Y=42mm, Y=683mm; 4.2.3.2 Regardless of the above dimensions all ballast must be within the cockpit and
no modifications to the Chassis are permitted other than to secure the ballast. 4.2.4 The CTM at his sole discretion may reweigh any Driver during the Season and adjust the
Driver ballast accordingly.
© Supercars – 2020 Division “G” Page G7 of G54 ISSUED JANUARY 2020
G4.3 Freedoms Permitted
4.3.1 No modifications to a Car as described in the Design or relevant VSD will be permitted
unless specifically permitted in the Rules and approved by the CTM:
4.3.1.1 holes providing minimal clearance are permitted to be drilled/made, solely to
allow the passage or fixing of a component permitted by the Rules;
4.3.1.2 brackets and/or mounting points are permitted to be added to mount other
accessories or components.
4.3.2 Throughout the Car, the use of any nut, bolt, screw, rivet, weld or adhesive may be used.
Where a method/type of attachment is specified in the Design the replacement method/type
must be of equal or superior strength and approved by the CTM.
4.3.3 Modifications permitted under the Rules are allowed only on the condition that the weights
and/or dimensions contained in the Rules, the Design and the relevant VSD are respected.
4.3.4 Where reinforcement is permitted by the Rules the material used must follow the original
shape and is in contact with it. The reinforcements must not create hollow sections and
must not allow 2 separate parts to be joined together to form 1.
4.3.5 The following areas are permitted to be reinforced:
4.3.5.1 The transmission tunnel at the point where the gear shift lever cradle mounts;
and
4.3.5.2 Both sides of the transmission tunnel at the centre bearing housing mounts.
4.3.6 It is permitted to join the body side inner at the B-Pillar to the ROPS by means of bracketry
not covered in the Design. The design of these connections is free apart from they must be
steel and comply with the following:
4.3.6.1 There must only be a maximum of two (2);
one (1) at the top of the B-Pillar (Z > 900mm); and
one (1) approximately in the middle of the B-Pillar (Z > 350mm); and
4.3.6.2 The X dimension must be no greater than 150mm and protrude no wider than
the body side inner where they are connected; and
4.3.6.3 The Z dimension must be no greater than 100mm.
4.3.7 Where components, which are allowed in the Rules, require a hydraulic or pneumatic
connection which is not specifically covered by the Design, hydraulic or pneumatic
connections between these components are allowed provided the sole purpose is to allow
the correct and normal primary functioning of the components they are connecting and do
not require the modification of the components they connect to.
4.3.8 It is permissible to protect the fuel filler necks from flying debris (specifically a delaminating
tyre) with a specific guard. This guard may take the form of a change in material and/or
construction of the boot side infill panels or a specific shroud for the filler necks. Any such
guard must have written approval of the CTM prior to being used in competition. Any such
guard may be fitted to both sides regardless of which side the fillers are fitted.
4.3.9 It is permitted to brace between the base of the “C” pillar and the rear Chassis rail. Such
brace must be constructed of material with a diameter of 25.4mm or less.
© Supercars – 2020 Division “G” Page G8 of G54 ISSUED JANUARY 2020
G4.4 Additional Accessories
4.4.1 Accessories which have no influence on a Car’s behaviour are permitted. For example,
equipment which improves the aesthetics or comfort of a Car’s interior (lighting,
heating/cooling, etc.). In no case may these accessories increase the engine power or
influence the steering, transmission, brakes or road holding, either directly or indirectly.
4.4.2 Where the road going version of a model of Car has a display screen in the centre area of
the dash, it is permitted to install a screen in that Car for the sole purpose of displaying
sponsor logos. Its location and size must remain similar to the particular model, and its
design must be approved by the CTM prior to construction and installation.
4.4.3 The screen may not, at any time, have an active wireless or Bluetooth connectivity, nor a
sim card installed.
4.4.4 Where a Team installs a screen in accordance with G4.4.2 above, the following will apply
to its use.
4.4.4.1 The screen may include the sponsors logo and/or tagline, but may not include
either of the following:
Moving image and/or video
Audio
4.4.4.2 Sponsor names may scroll through individually, or they may be displayed
collectively.
4.4.5 Teams must seek approval of the logos intended for use from Supercars prior to their
display.
G4.5 Composite Components
4.5.1 In addition to the approved Composite Material components contained in the VSD, the items
contained in Schedule G1.10 may be constructed from a Composite Material.
4.5.2 Bodywork which is manufactured from a Composite Material must be constructed in a
manner to ensure that any debris does not pose a risk of punctures to other Cars.
4.5.3 The following Bodywork is permitted to be constructed from Composite Material:
4.5.3.1 Driver door skin (Schedule G4)
4.5.3.2 Front guards, left front door skin, rear door skins (Schedule G5)
4.5.3.3 Rear quarter panels (Schedule G6)
NOTE: Where the layup of a particular component is specified as RA 175 T, it is permitted
to replace the specified material with equivalent material from different manufacturers or
with Innegra® where appropriate.
G4.6 Exotic Materials
4.6.1 The following materials must not be used in the construction or modification of a Car, except
as part of a Control Part or where specifically permitted by the Rules:
4.6.1.1 Titanium / Titanium alloy
4.6.1.2 Metal matrix composite (MMC) materials
4.6.1.3 Inter-metallic materials (Ti-Al, Fe-Al, Ni-Al, Ni-Co)
4.6.1.4 Iridium alloys (excluding spark plug electrodes)
4.6.1.5 Rhenium alloys
4.6.1.6 Alloys containing more than 5% Beryllium
© Supercars – 2020 Division “G” Page G9 of G54 ISSUED JANUARY 2020
4.6.1.7 Ceramic components and ceramic coatings – (excluding spark plugs, Bodywork
insulation coatings, exhaust coatings, piston coatings, front bumper bar under
trays, brake duct coatings).
G4.7 Manufacturing and Measuring Tolerances
4.7.1 When a Car is being examined, all measurements and tolerances will be those stated in the
Rules, Design, the relevant VSD and ESD.
4.7.2 Where a measurement is specified as a maximum or a minimum value, this represents the
limit of the permitted variation and no further tolerance will be applied.
4.7.3 All measurements will be taken at ambient temperature except where specified.
4.7.4 Any dispute regarding the compliance of a Car with any measurements in the Rules will be
assessed, where appropriate, by the inspection of samples either physical or electronic held
by Supercars or the Rules.
G4.8 Vehicle Datums
4.8.1 The Supercars Zero datum is located between the two (2) front Chassis rails inline with the
rear pivot point of the front lower control arm.
4.8.2 The Z-axis represents the vertical axis with the lower horizontal surface of the Chassis sill
being Z=0mm.
4.8.3 The X-axis represents the longitudinal axis with its positive element pointing to the rear of
the Car.
4.8.4 The Y-axis represents the lateral axis with its positive element pointing to the left if facing
the Car from the front.
4.8.5 All dimensions relating to the construction and or modification of a Car will be taken in race
condition without the Driver on board and will be expressed, where appropriate, in terms of
a distance from the fixed datum origins.
4.8.6 For all items that are duplicated symmetrically about the Car centreline, only the positive
value has been stated.
© Supercars – 2020 Division “G” Page G10 of G54 ISSUED JANUARY 2020
G5. SAFETY EQUIPMENT
G5.1 Seats
5.1.1 The Driver’s seat must be of a type homologated by the FIA to the 8862/2009 standard.
5.1.2 The LH mounting face of the Driver’s seat must be mounted between Y= 50mm and
Y= 60mm.
5.1.3 The inner face of the seat (padding removed) at the lower edge of the shoulder belt holes
must be no further rearward than X= 2020mm.
5.1.4 Each seat must be mounted to the seat mounting structures designed for the purpose within
the Chassis.
5.1.5 Each Competitor must have a Car which can be fitted with the required safety equipment
to undertake passenger rides when required.
G5.2 Leg Brace
5.2.1 Each Car must be fitted with a leg brace manufactured in accordance with the list of material
present in Schedule G8 and approved by the CTM.
5.2.2 The method of fixing if free.
5.2.3 The minimum weight of the leg brace complete assembly including mounting is 3.5kg.
5.2.4 The fitment of the leg brace is mandatory.
G5.3 Safety Harness
5.3.1 A Car must be fitted with a safety harness that complies with the requirements of FIA
Standard 8853/98 or 8853-2016, for each seat fitted in the Car, and must be fitted and worn
as required by the Rules.
5.3.2 The safety harness must be installed and used in compliance with Articles 6.2 and 6.3:
Safety Belts - Article 253 of Appendix J to the ISC of the FIA.
5.3.3 It is not permitted to attach any type of elastic or other springing medium/device to the
shoulder elements of the approved safety harness.
5.3.4 The safety harness of any Car involved in any accident must be inspected by the CTM at
the relevant Event. If appropriate, the Motorsport Australia Log Book will be endorsed with
a requirement by the CTM that the safety harness be replaced.
G5.4 Window/Racing Nets
5.4.1 Each Car is required to have fitted a Driver’s side window net, and where any Car is used
to carry a passenger while on the Circuit, the Car must also be fitted with a passenger’s
side window net. All window nets must comply with the requirements of Article 11:
Window/Nets - Article 253 of Appendix J to the ISC of the FIA in addition to the following:
5.4.1.1 They must be permanently attached to the ROPS along the lower edge of the
net;
5.4.1.2 They must be affixed to the ROPS above the relevant window by means of a
rapid release system so that, even when the Car is inverted, it must be possible
to detach the window net with 1 hand;
5.4.1.3 The window net when released from its operational position must retract so as
not to impinge on the door opening when the Car is inverted;
5.4.1.4 It is highly recommended that FIA 8863 2013 Racing Net/s (FIA Technical List
N° 48) be fitted to both the left and right hand sides of the Driver’s seat. These
© Supercars – 2020 Division “G” Page G11 of G54 ISSUED JANUARY 2020
nets must be fitted in accordance with the FIA and manufacturer instructions. In
the case of a Car fitted with a right hand racing net, it is not required to fit a
Driver’s side window net, however, the fitment of this window net is
recommended.
G5.5 Roll Over Protection Structure “ROPS”
5.5.1 Each Car must be fitted with a ROPS that is constructed in accordance with the Design and
the Motorsport Australia Issued Safety Cage Certificate Number 61-00528 which complies
with the requirements of Article 8: Rollover Structures - Article 253 of Appendix J to the ISC
of the FIA.
5.5.2 In accordance to Appendix J Article 253 of the ISC, all tubes of the cage identified by
drawing 253-68 and all roof reinforcements must be fitted with padding compliant with FIA
standard 8857-2001, type A (see technical list n°23 "Roll Cage Padding Homologated by
the FIA"). Each padding must be fixed in such a way that it is not moveable from the tube.
Padding is compulsory only on the Driver’s side, except for a passenger session, where it
must also be fitted to the passenger side.
G5.6 Fire Extinguisher Systems
5.6.1 Each Car must be fitted with a Lifeline 104-225-002 or 105-001-006 fire extinguisher
system, which complies with the requirements of Extinguisher Systems - Article 253 of
Appendix J to the ISC of the FIA in addition to the following:
5.6.1.1 All fire extinguisher systems must be fitted as per the manufacturer’s instructions.
5.6.1.2 The canister must be mounted on the front passenger side floor between the
following position:
X= +850mm and X= +1420mm; and
Y= -200mm and Y= -665mm.
G5.7 Tethers
5.7.1 At all times when on the Race Track, Cars must be fitted with four (4) approved tethers from
Amick-PWR, one (1) tether at each suspension corner.
5.7.1.1 The rear tethers must be as per the Design (PN: 1V8-101HMT2H).
5.7.1.2 Teams are responsible for the length of the front tethers.
5.7.2 All tethers must be attached to the Chassis and the upright to points that exceed the
breaking strain of the approved tether.
© Supercars – 2020 Division “G” Page G12 of G54 ISSUED JANUARY 2020
G6. BODY REQUIREMENTS
G6.1 Bodywork
6.1.1 All Bodywork must be identical to the samples both physical and/or electronic submitted by
each Homologation Team and/or recorded by Supercars during the homologation process
and must be:
6.1.1.1 used exclusively and in their entirety; and
6.1.1.2 used only for authorised Supercars activities.
6.1.2 In all cases where an area is designated or mounting points defined within the Design or
the Rules, these areas or mounting points must be used exclusively for the designated
purpose.
6.1.3 Windscreen wiper motors, their position and the blades and mechanism are free subject to
there being at least one (1) windscreen wiper which clears the windscreen in the Driver’s
line of vision. The windscreen washer device, the washer bottle and their location is free. It
will be permitted to locally modify the polycarbonate windscreen to allow fitment of the
windscreen wiper mechanism.
6.1.4 All external air line fittings must be located in or rearward of the “B” pillar (but in the general
vicinity of the “B” pillar) and must be recessed so they are not likely to cause injury.
6.1.5 The bonnet and boot lid must be secured, by at least two (2) separate fasteners for the
bonnet and two (2) separate fasteners for the boot lid, notwithstanding the hinging
arrangements.
6.1.6 The fasteners for the bonnet and boot must comply with the following:
6.1.6.1 The bonnet fasteners used must be of the design under British Patent 2089877
and all bonnet pins must be made of steel.
6.1.6.2 The boot fasteners used must be of the design under British Patent 2089877 and
may be modified to suit the application subject to the locking pin being retained
on the boot lid catch whilst not engaged.
6.1.7 The front bumper bar retaining bolts on the exposed face of the front bumper bar must be
either button heads or recessed into a retaining washer and all fixings must be able to be
removed with a 5mm allen key only.
6.1.8 The minimum weight for any front bumper bar with freestanding headlights, excluding its
mounting system, is 13.5kg.
6.1.8.1 The minimum weight for any front bumper bar and headlights moulded as a
unitary item, excluding its mounting system, is 16.5kg.
6.1.8.2 It is permitted to apply ballast to a front bumper bar to achieve the minimum
weight in accordance with Rule G6.1.8 and Rule G6.1.8.1. The ballast must be
securely attached to the bar at a location suitable to the Teams and with the
approval of the CTM.
6.1.9 It is permitted to support the rear of the undertray from the Chassis or crossmember.
6.1.10 Each Car that utilises wing end plate mounting is permitted to brace between the edge of
the boot gutter and the Chassis rail to support wing loadings. The use of any such brace is
subject to the prior approval of the CTM.
© Supercars – 2020 Division “G” Page G13 of G54 ISSUED JANUARY 2020
G6.2 Front Bumper Bar Air Intakes
6.2.1 It is permitted for air intakes in the front bumper bar to be partially or completely blanked
provided that any blanking complies with the following:
6.2.1.1 Radiator intake and brake ducts:
Blanking must only be fitted behind the homologated trim line of the radiator
intake or brake ducts and must be either flat sheet or tape.
No part on any component may protrude forward past the homologated trim
line of the radiator or brake ducts.
It is permitted to have adjustable blanking provided that any adjustment is
made while the Car is stationary. Such change is not permitted to be made
by the Driver.
6.2.1.2 Front bumper bar grille/s must be as homologated and as specified in the
relevant VSD.
G6.3 Windscreens
6.3.1 The front and rear windscreens must be of polycarbonate material with a thickness of 6mm
± 5% (the measurement does not include any tear offs or base coat) and must conform to
the shape of the make and model of Automobile the Car is based on.
6.3.2 The front and rear windscreens must be connected to the Chassis by a minimum of:
6.3.2.1 Bonding using a suitable bonding agent; and
6.3.2.2 Four (4) M6 bolts, one in each corner of the windscreen; and
6.3.2.3 A vertical brace in the centre of the front screen with tensioning capability.
6.3.3 If, as a result of damage, it is necessary to remove the front windscreen a replacement front
windscreen must be fitted. The fitment and retention of the replacement windscreen must
be inspected by the CTM prior to that Car being allowed to re-join the Circuit.
6.3.4 It is permitted to fit tear offs to the front windscreen.
6.3.5 It is permitted to fit a brace as detailed in the relevant VSD to the rear screen.
G6.4 Doors
6.4.1 Each door must be constructed as specified in the relevant VSD.
6.4.2 Each Car must be fitted with a side impact protection device in both the front and the rear
doors located on the Driver’s side as detailed in Schedule G3.
6.4.3 In addition to the above a carbon honeycomb panel as detailed in the relevant VSD must
be affixed to the ROPS and fitted to the front door aperture on the Driver’s side.
6.4.4 The windows in each door must be:
6.4.4.1 a clear polycarbonate insert with a minimum thickness of 4.00 mm.
6.4.4.2 the polycarbonate insert fitted to the front doors and rear doors must conform to
the shape of the make and model of Automobile the Car is based on.
6.4.4.3 the Driver’s and/or passenger’s side polycarbonate insert may be removed.
6.4.4.4 the polycarbonate inserts are permitted to be fitted with “NACA” ducts or
ventilation holes.
6.4.4.5 window mounted “NACA” duct must only be used for cooling the Driver and must
therefore only have the effect of circulating air within or extracting air from the
cockpit.
6.4.4.6 the front door window polycarbonate inserts must only be retained with the
© Supercars – 2020 Division “G” Page G14 of G54 ISSUED JANUARY 2020
specified “christmas tree” clip as detailed in the Schedule G7 and also must have
a handle hole located in the polycarbonate insert that complies with Schedule
G7.
6.4.4.7 the front door window polycarbonate inserts must be able to be removed by an
Official at any time if so required.
6.4.5 The inner door panels may be removed from all doors and the Driver’s door may be modified
to accommodate the fitment of a side impact protection structure as detailed in Rule G6.4.2
6.4.6 The original interior door trim may be replaced with an alternative panel.
6.4.7 If fitment is specified by the relevant VSD it will be permitted to substitute the standard
manufacturer supplied Chassis mounted door sealing rubber for an alternative aftermarket
sealing rubber provided it is visually similar and performs the same function as the standard
sealing rubber.
G6.5 Rear Vision Mirrors
6.5.1 A Car must be fitted with an internal rear vision mirror which has a reflecting surface of at
least 5000mm2, and the mirror must provide an unobstructed view to the rear of the Car.
6.5.2 A Car must be fitted with both a left and right hand side external rear vision mirror.
6.5.3 Unless otherwise permitted by the Rules, all external mirrors must remain as homologated.
It is permitted to remove the standard adjustment mechanism and replace with a fixed
support for the glass.
G6.6 Tow Hooks and Vehicle Recovery
6.6.1 All tools necessary for the removal of the front and rear bumper bars must be securely attached to the passenger side anti intrusion bar and be clearly identifiable to any Official.
6.6.2 A Car must be equipped with at least one (1) front and one (1) rear external towing strap which must conform to the following: 6.6.2.1 be constructed of suitable webbing material with a minimum width of 50mm; 6.6.2.2 permit the insertion of a round bar of 40mm diameter; 6.6.2.3 be fitted forward of the front axle and rearwards of the rear axle; 6.6.2.4 be clearly visible, including being of a colour in contrast to the colour of the
Bodywork immediately adjacent to the towing straps; 6.6.2.5 be constructed and fitted in such a way that they will not damage other Cars; 6.6.2.6 are capable of withstanding the loads applied during a recovery.
6.6.3 In addition to the requirements of Rule G6.6.2 above, a Car must be fitted with secondary internal tow straps, located inside the boot and under the bonnet, which will be used in more difficult recoveries. These secondary internal tow straps must: 6.6.3.1 be located in the boot and be securely attached to the defined points in the
Design, and form a ‘V’ or ‘Y’ configuration with a single connection point which extends past the extremities of the rear bumper bar and has an 80 mm diameter end loop.
6.6.3.2 be located under the bonnet with two (2) individual straps that are securely attached with a minimum length of 200mm with an 80 mm diameter end loop.
6.6.3.3 have adequate clearance around all components located in the boot and under the bonnet when being used.
6.6.3.4 be rated to a minimum load rating of 1.5 ton. 6.6.3.5 have gas struts to hold the boot lid open or similar must be fitted and be fully
operational. 6.6.4 The welded tags for the front tow hooks Part No: V8SC-1-048 are optional.
© Supercars – 2020 Division “G” Page G15 of G54 ISSUED JANUARY 2020
G6.7 Accessories
6.7.1 Any Driver cooling systems that contain a cooling medium in race ready condition must be:
6.7.1.1 mounted within the cockpit utilising the mounting points designated in the Design
for the passenger seat; and
6.7.1.2 constructed in a manner which to the satisfaction of the CTM, has been designed
to ensure the safe containment of the whole system during reasonably
foreseeable loading condition.
6.7.2 Any other components or accessories, regardless of weight, which are mounted within the
cockpit, must also be designed to ensure safe containment.
G6.8 Aerodynamics
6.8.1 Other than the Bodywork, no part of a Car is permitted which actually or potentially
increases downforce or reduces drag.
6.8.2 The CTM may at any time require:
6.8.2.1 any sensor/s to be fitted to a Car to measure the aerodynamic performance of a
Car; and
6.8.2.2 any Car to be tested for aerodynamic performance by any means and at any
location to ensure aerodynamic parity.
G6.9 Roof Duct
6.9.1 The fitment of the roof duct if fitted it may be blanked off on the roof surface.
6.9.2 The aperture in the roof must respect the internal shape of the roof duct.
6.9.3 The leading edge of the aperture in the roof must be 100mm ±10mm from the upper edge
of the windscreen aperture and in accordance with any instructions advised by the CTM.
6.9.4 The roof duct must be constructed in accordance with the Design and not be modified in
any way.
6.9.5 The attachment of additional ducting to the roof duct is permitted. The design of the
additional ducting is free provided its sole purpose is for Driver cooling.
© Supercars – 2020 Division “G” Page G16 of G54 ISSUED JANUARY 2020
G7. SUSPENSION
G7.1 Springing Medium
7.1.1 The springing medium on each corner of a Car must be ferrous of type coil-spring over damper.
7.1.2 The springing medium must consist of one (1) spring on each corner of a Car. 7.1.3 The spring must be of linear rate with a tolerance of +10% on its nominal rate. 7.1.4 The spring must have closed and ground ends. 7.1.5 The pitch of the spring past the first coil turn at either end must be consistent across the
length of the spring and be within 1mm. 7.1.6 The wire diameter of the spring past the first turn at either end must be consistent across
the length of the spring and be -within 1mm. 7.1.7 Bump rubber, bump rubber packer(s) and spring rubber need to be approved for use by the
HoM. 7.1.8 It is permitted to use one (1) bump rubber on each corner of a Car. The bump rubber must
be mounted on the damper shaft and not exceed 20mm in height. 7.1.9 The use of bump rubber packer(s) is permitted on each corner of a Car and the combined
height is free. The approved material are aluminium, Nylon and Acetal. 7.1.10 It is permitted to use one (1) spring rubber on each corner of a Car. 7.1.11 The spring rubber can only be engaged one turn. 7.1.12 The overall spring rate of all springing mediums in the system is free. 7.1.13 It is not permitted to fit any springing mediums which react the displacement of the damper
shaft inside the damper. G7.2 Front Suspension
7.2.1 The front suspension is free except that: 7.2.1.1 The type of suspension must be double wishbone. 7.2.1.2 The number and position of the suspension pivot points, as detailed in the
relevant VSD, must be used in their entirety and exclusively. 7.2.2 The damper mounts on the Chassis may be relocated within a 20mm radius of the approved
point. The dampers will be deemed to pivot and mount to the Chassis at the same point. 7.2.3 The coilover damper assembly fitted to the front suspension must be mounted to the
Chassis as detailed in the relevant VSD and must attach directly to the lower wishbone. 7.2.4 It is not permitted to use devices which vary the motion ratio on any suspension links unless
specifically permitted by the Rules. 7.2.5 The detachable front suspension crossmember is free, on the condition that:
7.2.5.1 it is possible to remove it from the Car (no attachment by welding); and 7.2.5.2 it utilises the mounting points as defined for this purpose in the Design; and 7.2.5.3 must not be constructed or modified in any way that in the opinion of the CTM
improves its aerodynamic effect on the Car. 7.2.6 The area defined in the Design for mounting the top wishbones may be modified with the
prior approval of the CTM in the following ways: 7.2.6.1 It will be permitted to affix within the defined area, mounting points to allow the
fitment of the various design of top wishbones. No part of the mounting system may protrude outside the area defined by the mounting boxes with the following exception:
The fixation for the wishbone mounting points may extend outside the
defined area provided the only purpose is to retain the wishbone mounting
points. (e.g.: bolt heads, weld fillets, etc.)
7.2.6.2 It will be permitted to locally modify the front upper wishbone mounting boxes as
defined in the Design solely to allow access to the wishbone mounting points.
© Supercars – 2020 Division “G” Page G17 of G54 ISSUED JANUARY 2020
7.2.7 The front suspension pivot points on the Chassis and detachable cross member may only
be at the approved point. This point must be used as the pivot point for the suspension.
G7.3 Front Upright
7.3.1 The minimum weight of each front upright must be 10.5 kg.
7.3.2 The weight of each front upright will be determined after:
7.3.2.1 disconnecting the front upright from the outer joints of the upper and lower
wishbones and steering arm; and
7.3.2.2 removing the brake rotor, brake hat and brake caliper; and
7.3.2.3 disconnecting all of the ducting and electrics at the closest joint to the front
upright.
7.3.3 The front upright weight will include all mounting bolts, nuts, washers and spacers removed
during disassembly of the front upright from the Car.
7.3.4 It must at all times be possible for the following components to be fitted to a Car:
7.3.4.1 Alcon CAR9529ZG51NSLT/RT front caliper;
7.3.4.2 Alcon DIV 2211X252A36 L/R front rotor and suitable mounting hat;
7.3.4.3 Supercars Control 17” Wheel with the 17” Dunlop Control tyre;
7.3.4.4 The caliper studs may be changed to suit.
7.3.5 It must be possible for the Car to be driven at racing speed on any Circuit in this
configuration.
7.3.6 The CTM will retain the appropriate sample parts.
7.3.7 Each drive peg for the front wheels must be affixed to the upright spindles as with the control
rear upright. Under no circumstances is a drive peg permitted to be retained in the Control
Wheel.
G7.4 Rear Suspension
7.4.1 The rear suspension must be constructed and utilised as defined in the Design.
7.4.2 Each pickup and mounting point must be used in their entirety and exclusively for their
intended purpose.
7.4.3 The clevises which mount the wishbones to the Chassis are free and may utilise a system
to allow for adjustment within the limits defined in the relevant VSD.
7.4.3.1 Structural interconnection between any or all of the clevises is not permitted.
7.4.4 The coilover damper assembly fitted to the rear suspension must be mounted to the Chassis
as detailed in the relevant VSD and must attach directly to the lower wishbone damper
mount as per the Design.
7.4.5 The damper mounts on the Chassis may be relocated within a 20mm radius of the approved
point. The dampers will be deemed to pivot and mount to the Chassis at the same point.
G7.5 Rear Spindle
7.5.1 The following modifications are permitted to the component detailed in AR-3020:
7.5.1.1 Thread direction and length are free, however all other thread detail must be
maintained; and
7.5.1.2 It will be permitted to modify the rear spindle to house individual design rear
wheel safety clips.
© Supercars – 2020 Division “G” Page G18 of G54 ISSUED JANUARY 2020
G7.6 Anti-Roll Bars
7.6.1 Both the front anti-roll bars (FARB) and the rear anti-roll bars (RARB) must comply with the
provisions of Rule G7.6.
7.6.2 Anti-roll bars must be constructed of one (1) torsion tube/bar for each axle.
7.6.3 Anti-roll bars must be mounted parallel to the Y axis of the Car.
7.6.4 A rocker, which varies the motion ratio between the anti-roll bar rigidly connected to the
Chassis and the respective lower wishbone is permitted.
7.6.5 Adjustment of the stiffness of the anti-roll bars from within the cockpit by the Driver is
permitted. The adjustment of stiffness must only be achieved by the rotation of either one
(1) or two (2) spring steel blades or by telescopic arms attached directly to either end of the
torsional tube/bar of the anti-roll bar mechanism.
7.6.6 The FARB must only be mounted to the underside of the front Chassis rails, which includes
the angled face.
7.6.7 Modification of the Chassis rail to allow fitment of a FARB rocker is permitted. Any such
modification:
7.6.7.1 must only support the rocker; and
7.6.7.2 will be permitted to extend no further than 50mm from the centreline of the rocker;
7.6.7.3 and no lower than the lower face of the Chassis rail;
7.6.7.4 and no further inboard than the inner face of the Chassis rail.
7.6.8 The RARB must only be mounted to the rear Chassis rails.
7.6.9 The centre line of the RARB must be:
7.6.9.1 no lower than Z = 280mm; and
7.6.9.2 no further rearward than X = 3095mm.
7.6.10 The torsion tube for the RARB must not exceed 50mm in outside diameter.
7.6.11 Unless otherwise specified, each link in the anti-roll bar system must be of a fixed length.
7.6.12 The link which attaches to the rear lower wishbone must use the unused damper mount on
each side, or connect to either the front or rear leg of the bottom wishbone exclusively via
a clamped or welded clevis.
7.6.13 No modification is permitted to any Chassis tubing to fit any part of any anti-roll bar system.
7.6.14 It is permitted to locally modify the rear sheet metal to allow fitment of the RARB.
7.6.15 The RARB rocker must only be fitted to the rear Chassis rail and modification of the rear
Chassis rail to allow fitment of the RARB rocker will be permitted. Any such modification
must only support the RARB rocker. Any modification within the rear Chassis rail will be
permitted to extend no further than 50mm from the centreline of the rocker spindle and must
not extend externally of the rear Chassis rail save for in the direction of the rocker spindle.
7.6.16 Each modification must have the prior written approval of the CTM.
G7.7 Suspension Adjustment
7.7.1 Where the Rules permit the adjustment of the suspension of a Car, the force required to make such an adjustment must only be generated and controlled as follows: 7.7.1.1 By a member of the Team permitted to work on the Car, while the Car is
stationary; or 7.7.1.2 By the Driver, seated normally in the Car with the safety harness correctly
fastened, when the Rules permit such an adjustment by the Driver from within the cockpit.
© Supercars – 2020 Division “G” Page G19 of G54 ISSUED JANUARY 2020
G7.8 Dampers
7.8.1 A Car must only be fitted with any of the dampers designated in Schedule G1.2.
7.8.2 Each damper listed in Schedule G1.2. must only be fitted with the corresponding piston
designated in the same table.
7.8.3 The dampers and their internal components as available and supplied by the manufacturer
must be equally available to each Team. No modification is permitted to any catalogue part
that may affect the passage of oil within the damper.
7.8.4 These will be identified by the means of detailed drawings, photographs, specifications and
samples held by Supercars.
7.8.5 The dampers must comply with the following requirements:
7.8.5.1 adjustment of any damper from the cockpit is prohibited;
7.8.5.2 each damper unit must function independently of each other, i.e. no connections
are permitted between damper units;
7.8.5.3 the use of electronically adjustable dampers is prohibited;
7.8.5.4 only one (1) damper per wheel is permitted; and
7.8.5.5 only four (4) damper characteristics that can be adjusted from the outside of each
damper are permitted, this number does not include gas pressure adjustment by
the adding or removal of gas.
7.8.6 The only form of droop control permitted is a solid spacer located internally in the damper
controlling the open length.
© Supercars – 2020 Division “G” Page G20 of G54 ISSUED JANUARY 2020
G8. ENGINE
G8.1 General
8.1.1 An ESD will detail an engine specification permitted for use in the Category. 8.1.2 Cars must only be fitted with an engine as detailed in an ESD relevant to that make of Car. 8.1.3 The maximum engine capacity will be 5000cc + 25cc.
8.1.3.1 With prior express permission in writing and with all restrictions applied by the CTM a cylinder block may be bored to achieve a total capacity of 5025cc. All other engine dimensions will still apply.
8.1.4 Each engine must have suitable provision for the cylinder heads, sump and rocker/cam covers to be sealed to the cylinder block so that the cylinder heads, sump and rocker/cam covers are not able to be removed. There must also be provision to affix seals to the water pump and/or timing cover to prevent the camshaft(s) from being removed from the engine. It is the Team’s responsibility to ensure any engine installed in a Car is sealed prior to the commencement of qualifying at any Event. Once an engine has been sealed, the seals must remain intact and legible at all times. These seals must only be removed by the CTM or with the express prior approval of, and subject to the conditions of, the CTM.
G8.2 Other Engine Components
8.2.1 Subject to the provisions of the Rules and the relevant ESD, all of the other components necessary for the functioning of the engine are free.
8.2.2 Unless specified in the relevant ESD the engine oil pressure/scavenge pump assembly must be mounted to the engine (to either side) and be belt driven, via an adaptor, off the nose of the crankshaft.
8.2.3 The oil tank must be positioned in the left rear of engine bay in the area between the firewall and left top damper mounting point. 8.2.3.1 The fill point of the oil tank must be located under the bonnet or in the scuttle
panel in the vicinity of the bottom left corner of the windscreen. If located in the
scuttle panel it must be fitted with a suitable dry break fitting.
8.2.4 Each Car must be fitted with crankcase/oil tank breather/s discharging to the atmosphere and have fitted to such breather/s an oil-trap container (which must be empty at the start of Competition) of at least three (3) litres capacity.
G8.3 Cooling System
8.3.1 The water radiator must be mounted as follows: 8.3.1.1 The front top edge of the water radiator core must be located at:
X = -470mm ± 5mm Z = 380mm ± 5mm
8.3.1.2 The water radiator must be installed such that the bottom of the water radiator sits closer to the front of the Car than the top of the water radiator.
The front face of the water radiator core must be at an angle of 5.0°± 0.5 degrees.
8.3.2 The size permitted for the water radiator core is: 8.3.2.1 Width = 730mm ± 5mm 8.3.2.2 Height = 355mm ± 5mm
8.3.3 Unless specified in the relevant ESD the cooling system must be arranged so the general direction of flow of engine coolant is from the water radiator to the cylinder block and then to the cylinder heads.
8.3.4 The airflow through the water radiator core must be at an angle of 90 degrees to the front face of the water radiator core.
8.3.5 Ducting to the front face of any engine radiator must be from the central orifice in the front
© Supercars – 2020 Division “G” Page G21 of G54 ISSUED JANUARY 2020
bumper bar.
8.3.6 Ducting of air from the rear of any radiator is prohibited. 8.3.7 Engine oil heat exchangers, be they oil/air or oil/water are free and ducting to them is
permitted however ducting from the rear is not permitted, subject to the heat exchangers and associated ducting being located within the perimeter of the Bodywork and not lower than the lower edge of the front bumper bar.
8.3.8 If an oil/air heat exchanger is used in the same plane, in a unitary assembly with the water radiator, the combined core dimensions must respect those dimensions and restrictions applied to the water radiator core.
8.3.9 No part of any ducting is permitted forward of a line drawn between the upper and lower edges of the rear opening in the front bumper bar.
8.3.10 Unless otherwise specified in the ESD: 8.3.10.1 All other components of the cooling system, including fans, screens and catch
tanks are free. 8.3.10.2 The water pump must be driven directly by the crankshaft via a belt and must be
mounted above the crankshaft on the front of the engine. G8.4 Exhaust System
8.4.1 Each Car must be fitted with an exhaust system. 8.4.2 The outlet pipe/s of the exhaust system must utilise the cut-out provided in the left-hand sill
for the purpose. 8.4.3 The outlet pipe orifices must not:
8.4.3.1 project in any way beyond the maximum width of the Bodywork; and 8.4.3.2 terminate at a point more than 20mm outside the adjacent Bodywork.
8.4.4 Each exhaust pipe must be adequately protected in order to prevent burns. 8.4.5 The exhaust system must be a complete and continuous unit and exhaust gas may exit only
at the end of the system. 8.4.6 Each Car must be fitted with effective mufflers which diminish the sound of the engine
exhaust noise so that the maximum exhaust noise does not exceed 95dB(A) measured at 30 metres from the side of the Circuit by approved measuring equipment.
8.4.7 The exhaust primary headers on a Car must have a nominal thickness of at least 1.2mm (18 gauge).
G8.5 Inlet System
8.5.1 The inlet/induction system for pushrod engines is detailed in the relevant ESD. 8.5.2 The inlet /induction system for overhead cam engines is detailed in the relevant ESD. 8.5.3 The following applies to all inlet/induction systems:
8.5.3.1 The engine must be naturally aspirated; and 8.5.3.2 With the exception of ambient atmospheric air and the specified control fuel, no
other substance may be added to the intake charge of the engine; 8.5.3.3 The inlet must be of a fixed length; 8.5.3.4 Throttle actuation for a Car must be exclusively by “butterfly”.
8.5.4 With the exception of the full throttle stop and idle adjuster, any device which allows the throttle to be artificially positioned by resisting the force of either the Driver’s foot or the throttle return mechanism is prohibited.
8.5.5 The throttle linkages must be fitted with suitable return springs which, in the event of a failure in the throttle linkage will return each throttle bank to the closed position.
8.5.6 Only one (1) fuel injector per cylinder is permitted which must only inject fuel directly into the side or the top of the manifold or trumpet.
8.5.7 Air for the engine must only be ducted from the large centre orifice in the front bumper bar.
© Supercars – 2020 Division “G” Page G22 of G54 ISSUED JANUARY 2020
G8.6 Engine Mounting
8.6.1 Engine mounting systems must only mount the engine to the removable front suspension crossmember as defined in Rule G7.2.5.
8.6.2 The engine must be mounted in either of the following manners: 8.6.2.1 by the mounting points intended for that purpose on the approved cylinder block;
or 8.6.2.2 by the sump with two (2) mounting points with a maximum of M10 thread located
in the area between: X= 0mm and X= -105mm; and Y= ±105mm and Y= ±130mm.
G8.7 Engine Weight
8.7.1 The total minimum engine weight is 200 kg dry. 8.7.1.1 Ballast to comply with the minimum weight and/or centre of gravity regulations
must be affixed to the engine unless specifically authorised in writing by the CTM. 8.7.1.2 All engine ballast either affixed to the engine or Chassis as authorised by the
CTM must have provision to be sealed. It is the Team’s responsibility to ensure the seals are fitted and intact during any Competition.
8.7.2 Any time the engine is weighed for compliance with Rule G8.7.1 and Rule G8.7.1.1 it must be in the configuration as detailed in the ESD nominated for that Car.
8.7.3 Any connectors from the engine to the Car must be disconnected at the joint closest to the engine.
8.7.4 The wiring loom must be disconnected at the firewall. G8.8 Flywheel
8.8.1 Each Car must be fitted with a steel flywheel. 8.8.2 The minimum weight of the flywheel including clutch cushioning buttons and crank trigger
teeth will be 2.0kg. 8.8.3 The flywheel ring-gear must be an integral part of the flywheel. 8.8.4 The flywheel must mount directly to the crankshaft. G8.9 Clutch
8.9.1 A Car must only be fitted with a clutch as designated in Schedule G1.3. 8.9.2 Each clutch listed in Schedule G1.3 will be identified by the means of detailed drawings,
photographs, specifications and samples held by Supercars. 8.9.3 The clutch must comply with the following requirements:
8.9.3.1 mount directly to the flywheel;
8.9.3.2 only have three (3) driven plates that transmit torque directly to the tailshaft; 8.9.3.3 be controlled exclusively by the Driver’s foot via an actuation system as part of
the Control Pedal Box. Systems other than this may be approved by Supercars under exceptional circumstances;
8.9.3.4 with the exception of the fixed pedal stops, any device which allows the clutch to be artificially positioned, or its speed of engagement to be varied by resisting the force of either the Driver’s foot or the diaphragm spring is prohibited;
8.9.3.5 the use of carbon fibre components within the clutch is permitted; 8.9.3.6 the machining of surfaces for the purpose of achieving clutch plate pre-load is
permitted.
© Supercars – 2020 Division “G” Page G23 of G54 ISSUED JANUARY 2020
G9. FUEL SYSTEM
G9.1 Fuel Tank Requirements - General
9.1.1 Each Car must be fitted with an ethanol compatible fuel tank conforming to the FIA FT3 specification as specified in Schedule D1 Table 6. 9.1.1.1 The fuel Cell is to be inspected in compliance with the following requirements:
Inspection of a fuel cell shall become due on the FIA expiry date of 5 years after manufacture;
Inspection of a fuel cell shall be carried out by the Manufacturer every 2 years;
Maximum life of a fuel cell shall be 15 years from the date of manufacture; A damaged fuel cell shall not be repaired; Proof of inspection must be supplied to The CTM on request; and
Test details are to be recorded by the CTM in the Log Book change of details section.
9.1.2 All parts of the fuel system rearward of the front fire wall must comply with the Design and the provisions of the Rules.
9.1.3 The fuel cell and its housing must be: 9.1.3.1 Housing Part # V8SC-8-10035 9.1.3.2 Fuel Cell (Large bladder) Part # COF-8-10027A 9.1.3.3 Fill pipes/Flanges Part # COF-8-10020A,0023A and 0024A. 9.1.3.4 Restrictors Part # COF-8-10043A
9.1.4 The following modifications are permitted to the fuel system: 9.1.4.1 Fitment of up to five (5) lift pumps;
The clearance between the lowest part of all lift pump assemblies (pump and filter as specified in the Design) and the floor of the fuel bladder must not exceed 5mm.
The location of the 5th lift pump (if used) can be suited to a Circuit direction providing it is affixed in one of the locations provided by the control bladder.
9.1.4.2 Fitment of an internal collector pot with three (3) high pressure pumps installed in accordance with the Design.
9.1.4.3 Amend the fuel hose layout detailed in the Design between the rear firewall and the fuel housing subject to the following conditions:
The specifications of all fittings, and hoses to suit, must be as detailed in COF-8-10012-C;
Both fuel filters must be located on the right hand side of the fuel tank housing;
The fuel pressure regulator position must be above the fuel tank housing and under the sheet metal;
It is permissible to use a drybreak in the line between the fuel pressure regulator and the rear firewall;
The rear firewall bulkhead fitting must be located on the right hand side of the Car centreline;
A maximum of two (2), fill/drain lines must be located through the right hand side access panel of the fuel bladder. The fuel lines connected to these inside the fuel bladder are optional.
9.1.4.4 Amend the fuel hose layout detailed in the Design between the rear firewall and
the FIA Siamese fitting subject to the following conditions:
It is permitted to add a drybreak fitting in the vent and filler line for the
purpose of refuelling the Car.
© Supercars – 2020 Division “G” Page G24 of G54 ISSUED JANUARY 2020
G9.2 Fuel Pressure
9.2.1 At all times when the throttle position exceeds 94.9% the maximum permitted fuel pressure is 5.5 bar.
9.2.2 The fuel pressure regulator must be as per 0 and must be fitted in accordance with the Design.
G9.3 Fuel Lines
9.3.1 Any fuel line that carries fuel through the cockpit must: 9.3.1.1 be flexible; and 9.3.1.2 be Dash 8 in size; and 9.3.1.3 have threaded, crimped or self-sealing connectors; and 9.3.1.4 an outer braid resistant to abrasion and flame (will not sustain combustion); and 9.3.1.5 have minimum burst pressure of 70bar (1000 psi) measured at a minimum
operating temperature of 135°C (250°F), excluding the connections to the injectors.
9.3.2 In addition to the provisions of Rule G9.3.1, the routing of the fuel lines through the cockpit must be located to the right hand side of the Car centreline.
9.3.3 The fuel flow sensor if fitted must be above the fuel cell between the fuel pressure regulator and the bulkhead fitting for the engine feed.
G9.4 Capacity
9.4.1 The total capacity of the entire fuel system must not exceed the marked volume of the Supercars fuel tank capacity checking vessel which is approximately 111 litres.
9.4.2 The total capacity of the entire fuel system may be adjusted to ensure compliance with Rule G9.4.1. 9.4.2.1 It is permitted to externally access the fuel capacity adjustment. 9.4.2.2 Should externally adjusted fuel capacity be used it must:
be located in the access panel of the right hand side; and be cylindrical in shape with a maximum diameter of 60mm; and be open to the atmosphere on its top surface; have the approval of the CTM.
G9.5 Fuel Tank Vent
9.5.1 The fuel tank must be vented externally of the Bodywork and include a suitable roll over valve.
G9.6 Fuel Fillers
9.6.1 No part of the FIA Siamese fitting assembly may be positioned further inboard than Y = ± 525mm.
9.6.2 The fuel and vent hoses in the boot must be Premier flexible boot hose 2.25”. 9.6.2.1 The minimum total flexible length for the front hose is 460mm. 9.6.2.2 The minimum total flexible length for the rear hose is 610mm. 9.6.2.3 The front and rear hoses may include one (1) aluminium bend each. 9.6.2.4 The minimum length of hose engagement for each and every connection is
35mm. 9.6.3 For Events where there is no refuelling during all races, it is left to the discretion of the
Teams to comply with Rule G9.6 in its entirety, or 9.6.3.1 Remove the FIA Siamese fitting. (A blanking plate will be approved) 9.6.3.2 And remove the fuel and vent Premier hose and aluminium bend. 9.6.3.3 And cap the fuel and vent at the firewall. It is permitted to use a drybreak on the
vent and filler cap for the purpose of filling up the Car.
© Supercars – 2020 Division “G” Page G25 of G54 ISSUED JANUARY 2020
G10. DRIVETRAIN
G10.1 General
10.1.1 The list of components approved for use in the drivetrain are designated in table 3 of
Schedule G1.3.
10.1.1.1 Teams and/or suppliers are able to submit a written request to Supercars to place
an alternate part onto the list. This request must be accompanied by detailed
designs, cost and evidence of validation on a Car. Where evidence of validation
is required, the CTM may permit the components to be used on a Car.
10.1.2 The list of Control Parts approved for use in the drivetrain are designated in table 3 of
Schedule G1.3.
10.1.3 The Design details for the location and retention of the bearing necessary for the Bell
Housing Shaft is contained in drawing V8SC-4-060-C.
G10.2 Transaxle
10.2.1 Each Car must only be fitted with an Albins ST6 transaxle.
10.2.2 All replacement parts will be required to be purchased through Albins and conform to the
parts listed in the transaxle drawing titled ST6 which are held by the CTM.
10.2.3 Reverse gear must be able to be selected by the Driver when seated in the Car in ready to
race conditions.
10.2.4 It is permitted to substitute the Dash 4 feed line to the Ring and Pinion oiler with an alternate
type of hose and fittings. Each fitting on the transaxle must remain as supplied by Albins
and the alternate hose must remain Dash 4.
10.2.5 It is permitted to mount a permanent line with a drybreak coupler at each end for the purpose
of filling the transaxle with oil. The drybreak at the transaxle end must replace an inspection
plug. Except for within the cabin, the location of this line is free.
G10.3 Gear Lever
10.3.1 The gear lever must respect the design of the Albins drawing titled ‘Shift Assembly - 14471’.
10.3.2 It will be permitted to vary the ratio and overall length of the gear lever.
10.3.3 If the ratio as stipulated in the Albins drawing is not respected, Teams will not have any
recourse with any Control Part supplier.
© Supercars – 2020 Division “G” Page G26 of G54 ISSUED JANUARY 2020
G10.4 Drop Gear Ratios
10.4.1 Only the drop gear ratios designated in the following table will be permitted to be used at
the following Circuits unless otherwise advised by Supercars:
Circuit Drop Gear Ratio Teeth
Adelaide Parklands 2 Circuit 1.13 23/26
Albert Park Grand Prix Circuit 1.07 27/29
Barbagallo Raceway 1.07 27/29
Hidden Valley Raceway 1.042 24/25
Mount Panorama Circuit 0.931 29/27
Newcastle East Street Circuit 1.13 23/26
Phillip Island Grand Prix Circuit 1.00 23/23
Pukekohe Park Raceway 1.07 27/29
Queensland Raceway 1.07 27/29
Sandown International Raceway 1.042 24/25
Surfers Paradise Street Circuit 1.07 27/29
Sydney Motorsport Park 1.00 23/23
Symmons Plains International Raceway 1.07 27/29
The Bend Motorsport Park 1.00 23/23
Townsville Street Circuit 1.07 27/29
Winton Motor Raceway 1.13 23/26
G10.5 Transaxle Cooling
10.5.1 Each Car must be fitted with a Transaxle cooling system which complies with the Design
drawing number V8SC-7-001 or V8SC-7-002.
10.5.2 It is permitted to add a screen to the front of each transaxle oil radiator and include a dry
break fitting to aid in its removal.
10.5.3 It will be permitted to modify the transaxle cooler upper and lower mounting points to include
anti vibration mounts. No such modification may change the angle or position of each cooler
as specified by the Design.
G10.6 Gear Shift Cut
10.6.1 Parameters for gear shift cuts will be as follows:
10.6.1.1 Transmission shift timing torque reversal: minimum 80ms
10.6.1.2 Transmission shift timing recovery: minimum 15ms
10.6.1.3 Transmission gearbox position sensor tolerance: 75mV
10.6.1.4 Transmission shift torque: maximum 15%
G10.7 Tailshaft Hoops
10.7.1 The fitment of tailshaft hoops, as detailed in the Design, to the Car is optional.
© Supercars – 2020 Division “G” Page G27 of G54 ISSUED JANUARY 2020
G11. BRAKES
G11.1 General
11.1.1 Each Car must be fitted with a dual circuit braking system operated by the same pedal. The
pedal shall normally control braking to all four (4) wheels. In the case of leakage at any point
of the brake system, its pipes or any kind of failure in the brake system, the pedal must still
control at least two (2) wheels.
11.1.2 Each Car must use the Control Parts designated in the table in Schedule G1.5.
11.1.3 It is permitted to:
11.1.3.1 use the brake pressure sensors to activate the brake lights; and
11.1.3.2 fit a brake light switch.
11.1.4 Only one (1) brake caliper and two (2) brake pads per wheel are permitted.
11.1.5 During a brake pad change, all displaced fluid must return to the master cylinder reservoir
through the master cylinder.
11.1.6 Machining of the brake rotor surface to extend the usable life of the brake rotor is permitted
provided that the disc groove design remains identical to the original brake rotor as supplied
by the manufacturer.
11.1.7 The only modifications permitted to the control calipers listed in Schedule G1.5 are:
11.1.7.1 Anti-knock back springs may be deleted; and
11.1.7.2 Drilling and tapping to fit the brake duct. Any such drilling must have the prior
approval of the Control Part supplier and the CTM.
11.1.8 The control brake rotors and calipers will be identified by the means of detailed drawings,
photographs and specifications retained by the CTM.
G11.2 Pedal Box
11.2.1 Pedal box mounting frame and bobbins must remain as specified in the following drawings
or assemblies:
11.2.1.1 Option 1:
V8SC-MSTR-24-01; and
COF-1-0012 x3; and
COF-1-0013 x1; and
COF-1-0014 x2.
11.2.1.2 Option 2:
V8SC-MSTR-38-01.
11.2.2 Either Option 1 or Option 2 as described in Rule G11.2.1.1 or Rule G11.2.1.2 must only be
used in their entirety with the exception of modification of the pedal rails COF–1–0012–
0014 inclusive is permitted.
11.2.2.1 The permitted modification of these parts is limited to a maximum of 10mm of
material removal from the top surface only.
11.2.2.2 The holes in the pedal rails COF–1–0012–0014 may be filled and rethreaded to
allow finer adjustment of the control pedal box.
11.2.3 The mounting location of the pedal box is free subject to the following:
11.2.3.1 The brake master cylinders must be able to achieve full stroke; and
11.2.3.2 Local modification of the firewall/tunnel sheet metal is permitted; and
11.2.3.3 No part of the pedal box is permitted inboard of Y= 125mm.
© Supercars – 2020 Division “G” Page G28 of G54 ISSUED JANUARY 2020
11.2.4 A Car specific adaptor plate is permitted for mounting the control pedal box.
11.2.4.1 Each Team must ensure the design, material and fitment of this adaptor plate is
fit for purpose.
11.2.5 An alternate brake pedal, with part number AS 3118 is permitted.
11.2.6 The throttle pedal is free but must conform to any requirements in the relevant ESD.
11.2.7 The interface between the Driver’s feet and the control clutch, brake and throttle pedals (i.e.
the pedal pads) is free.
G11.3 Brake Pads
11.3.1 At an Event, a Car must be fitted only with the brake pads designated in Schedule G1.5.
G11.4 Other Brake System Requirements
11.4.1 The fitment of a brake lock valve is optional, however the operation of the brake lock valve
if located on the steering wheel must only be operated by an on/off switch. If a cable or
hydraulic system is in operation it must only be located and operated by a lever located on
either side of the Driver’s seat.
11.4.2 The brake lock mechanism is only permitted to be used to stop the Car rolling from a
standing start.
11.4.2.1 The brake lock mechanism if fitted, may be engaged during a pit stop for the sole
purpose of stopping the rear wheels from turning during that stop.
11.4.2.2 Use of the brake lock mechanism in any situation/environment other than Rule
G11.4.2 and Rule G11.4.2.1 is not permitted.
11.4.3 The braking system pressure in both front calipers must remain equal at all times.
11.4.4 The control pedal box provides a system, which allows the brake balance of a Car to be
adjusted manually by the Driver. The force required to make such an adjustment must be
generated and controlled by the Driver, seated normally in the Car with the safety harness
correctly fastened.
G11.5 Brake Ducting
11.5.1 It is permitted to fit a duct to each front upright which must comply with the following:
11.5.1.1 The intake for the front brake ducts must only be from the two (2) outer orifices
in the front bumper bar.
11.5.1.2 No part of any such ducting will be permitted to extend outward past the inner
face of the rotor with the exception of a duct to feed air into the caliper. Any such
duct must not protrude past the edge of the caliper.
11.5.1.3 It will be permitted to vary the air flow through vanes of the rear brake rotors by
blanking or partially blanking the inner circumference of the rear brake rotor.
11.5.1.4 No device other than a simple duct is permitted.
11.5.1.5 Only cooling by channelling ambient air to the brakes is permitted.
© Supercars – 2020 Division “G” Page G29 of G54 ISSUED JANUARY 2020
G12. STEERING
G12.1 General
12.1.1 The mechanical principal must be rack and pinion.
12.1.2 The components of the steering are free with the exception of the control collapsible
steering column as detailed in Schedule G1.2.
12.1.2.1 It is permitted to include more than one column clamp.
12.1.3 The secondary shaft of the control collapsible steering column must pass through the
firewall between the upper and lower members of the ROPS cross.
12.1.4 A structure to house the lower column bearing is permitted.
12.1.5 It is mandatory to utilise a quick release system for the steering wheel.
12.1.5.1 The type of quick release system is free.
12.1.5.2 The control collapsible steering column bolt-on spline may be modified and/or
replaced.
12.1.6 Power steering is permitted, but must only be hydraulic in its operation and control.
12.1.7 No system which varies the output pressure and/or volume of the power steering hydraulic
pump whilst the Car is in motion is permitted.
12.1.8 The power steering hydraulic pump must be directly driven by the engine.
12.1.9 It is permitted to fit a cooler to cool the power steering fluid.
12.1.10 The steering wheel is permitted to house switches and/or the control dash display.
© Supercars – 2020 Division “G” Page G30 of G54 ISSUED JANUARY 2020
G13. WHEELS
G13.1 Control Wheel
13.1.1 A Car must only use the Supercars control wheel as detailed in the Design.
13.1.2 All Cars are required to have a minimum of twelve (12) wheels, four (4) for permanently
mounted wet control tyres and eight (8) for dry control tyres.
G13.2 Centre Lock Spindles and Wheel Nuts
13.2.1 Centre-lock spindles must be fitted with a safety clip/spring which must effectively prevent
the wheel nut from coming loose at any time. This safety clip/spring must:
13.2.1.1 be in place on the wheel nut at all times while a Car is on the Circuit; and
13.2.1.2 be replaced/reset after each wheel change; and
13.2.1.3 the safety clip/spring must be coloured red or orange where appropriate;
13.2.1.4 not protrude past the sidewall of the tyre in the horizontal plane in ready to race
condition.
13.2.2 A Car that participates in a race at an Event must only be fitted with wheel nuts that conform
to all of the requirements of the Supercars wheel nut specification as contained in Schedule
G2.
G13.3 Wheel Coatings
13.3.1 It will be permitted to paint and/or powder coat the Supercars control wheel.
13.3.2 Any markings on the Supercars control wheel must remain legible regardless of any
coatings.
© Supercars – 2020 Division “G” Page G31 of G54 ISSUED JANUARY 2020
G14. ELECTRICAL SYSTEM
G14.1 General
14.1.1 Each Car must be wired only in accordance with the Supercars control pinout document. 14.1.2 No part or component, however described, is permitted to influence the operation of the
electrical system unless specifically permitted by the Rules. 14.1.3 The wiring loom must be visible along its entire length when mounted in a Car. 14.1.4 The wiring loom must be easily removable from a Car within a reasonable time period at
the request of the CTM. 14.1.5 Any wiring that is required to go through the engine and/or rear firewalls, unless specified
otherwise, must use a pin to pin connector or use a wiring grommet for sealing. 14.1.6 All control wiring connectors must have a red heatshrink band within 100mm of the back of
the connector for ease of identification. 14.1.7 Switches to operate the electrical system may be fitted to a Car. Where permitted by the
Rules, these switches must be mounted in a location able to be operated by the Driver seated normally in the Car with the safety harness correctly fastened. 14.1.7.1 these switches may either be electromechanical or electronic in operation.
G14.2 Master Isolation Switch
14.2.1 A battery master isolation switch is mandatory and must: 14.2.1.1 disconnect the battery from the alternator and all electrical circuits; and 14.2.1.2 stop the engine; and 14.2.1.3 be spark proof; and 14.2.1.4 be able to be triggered from inside and outside a Car.
14.2.2 The external trigger must be: 14.2.2.1 situated near the lower part of the windscreen, on the Driver’s side; and 14.2.2.2 marked by a red spark in a white edged blue triangle with a base of at least
120mm.
G14.3 Battery
14.3.1 The battery fitted to a Car must be either detailed in Rule G14.3.1.1 or Rule G14.3.1.2: 14.3.1.1 ‘dry cell’ lead acid technology. 14.3.1.2 Lithium technology with the approval of the CTM.
14.3.2 Each battery must be mounted in the Car: 14.3.2.1 with the largest sides (in surface area) of the battery parallel to the YZ reference
plane; and 14.3.2.2 with the longest edges of the battery horizontal; and 14.3.2.3 with the terminals positioned either at the top of the battery or on the side which
faces the front of the Car; and 14.3.2.4 so it sits against the front vertical face of V8SC-RPNL-01L-01; and 14.3.2.5 seated in a tray constructed of 2.0mm steel with three (3) vertical sides of
minimum 20mm height; and 14.3.2.6 so that V8SC-RPNL-01L-01 forms a 4th vertical side; and 14.3.2.7 so the tray is firmly fixed to the metal work of the Chassis it is in contact with.
14.3.3 Each battery is to be held to the Chassis by means of two (2) steel clamps or straps that must: 14.3.3.1 be electrically insulated; and 14.3.3.2 be a minimum of 3mm thick; and 14.3.3.3 be a minimum of 20mm wide; and 14.3.3.4 be attached to the Chassis with four (4) bolts/studs at least 10mm in diameter;
and 14.3.3.5 have counterplates of at least 3mm thick with a surface area of at least 20cm2
© Supercars – 2020 Division “G” Page G32 of G54 ISSUED JANUARY 2020
beneath each bolt. 14.3.4 The entire battery installation must be completely covered by an electrically insulated cover.
14.3.4.1 If the control battery is used, only the electrical terminals need to be electrically insulated.
G14.4 Alternator
14.4.1 The alternator is free except that it must be mounted at the front of the engine, to either side, and be belt driven.
G14.5 Lights
14.5.1 The following lights must be from the production Automobile unless specified in the relevant VSD. These lights must be functional: 14.5.1.1 Headlamps either main beam or high beam or LED running lights; and 14.5.1.2 tail lights; and 14.5.1.3 brake lights; and 14.5.1.4 rear turn indicators.
14.5.2 A high level interior brake light must be fitted. 14.5.3 The globe type for the lights listed in Rule G14.5.1 and Rule G14.5.2 are free. 14.5.4 Headlamps, either main beam, high beam or LED running lights may be manually flashed
by the Driver on the Circuit. They may only flash simultaneously and must be controlled only by the Driver. 14.5.4.1 It will be permitted to automatically flash the headlights in any pattern when the
pit speed limiter is engaged. 14.5.5 Coloured or sign written headlights are permitted, except for any shade of the colour red,
unless otherwise approved by the CTM. 14.5.6 For a Car with a freestanding headlight, it is permitted to seal the head light to the front bar.
This sealing must be only where the headlight touches the Front bar and not be visible from the front. It is not permitted to externally tape the headlight to the bar.
G14.6 Starter Motor
14.6.1 The starter motor is free except that it must: 14.6.1.1 be exclusively electrically powered; and 14.6.1.2 engage directly with the flywheel; and 14.6.1.3 be capable of starting the engine at all times.
14.6.2 The starter motor may be mounted in front of, or behind the flywheel. 14.6.3 At all times the Driver, when seated and secured in the Car as for Competition, must be
able to activate the starter motor without outside or external assistance.
G14.7 Fuel Pump Power Supply
14.7.1 Each Car must be fitted with a system that cuts off the power supply to all fuel pumps after a maximum of two (2) seconds absence of crankshaft rotation.
14.7.2 It is permitted to fit an override system for the sole purpose of pumping fuel out of the Car. 14.7.3 The voltage supplied to each fuel pump must not be intentionally varied by any means.
G14.8 Identification Lights
14.8.1 A Car must be fitted with high intensity identification lights which must be Britax XT3. Other similar types of lights may be used with the prior approval of the CTM.
14.8.2 The identification lights will be required to be fitted so they both can be seen through the lower left hand corner of the windscreen and the top front corner of the rear passenger windows.
14.8.3 The Driver must be able to turn the identification lights on or off while driving.
© Supercars – 2020 Division “G” Page G33 of G54 ISSUED JANUARY 2020
G14.9 In Car Camera System 14.9.1 A Car must have the ability to be fitted with an in Car camera system for use by the
broadcaster. 14.9.2 The in Car camera system must be located in the position detailed in the Design. 14.9.3 The in Car camera system must be mounted securely and to the satisfaction of the CTM.
© Supercars – 2020 Division “G” Page G34 of G54 ISSUED JANUARY 2020
G15. ECU & DATA SYSTEMS
G15.1 Control Electrical Package
15.1.1 Except for that permitted in Rule G4.4.2, a Car must only be fitted with the control electrical package components designated in the table in 0.
15.1.2 It is only permitted to use the quantity of the components listed in the table in 0 in a Car. If no quantity is listed the amount is free.
15.1.3 The components which form part of the control electrical package must be installed in a Car in the location listed in the following table:
15.1.4 The control condition, as set in the PDM configuration, must be such that the equipment linked to output 19 (TPMS, TV Cameras, VCS Cameras, CPS Lights) must be switched on and supply a 12 volt nominal at all times the master switch is on.
15.1.5 The GPS antenna must be positioned on the outer surface of the boot on the centreline and near the top edge closest to the rear windscreen. The GPS antenna should be affixed with a suitable double sided tape.
15.1.6 A Car may be fitted with a Centre Console. 15.1.6.1 The location of this Centre Console must be such that Driver activated controls
are easily accessible by the Driver seated normally in the seat with the belts tight. 15.1.6.2 The size of this Centre Console must be such that the wiring and electrical items
housed within it take up the majority of its volume. 15.1.7 The components which form part of the control electrical package located on the passenger
floor or the Centre Console must be anti-vibration mounted, either individually or collectively via a mounting tray.
15.1.8 The specific locations in a Car where the mounting of the components in the control electrical package must be installed are as follows: 15.1.8.1 ADR (P12): Any part of the ADR, on the floor to the right hand side of the Driver’s
seat rear lower mounting bolt. 200mm ±5mm inboard from V8SC-MSTR-19RA and 8mm +/-5mm in front of V8SC-MSTR-15RF with the plug orientated to the right.
15.1.8.2 MSE/TV Comms (P13, P16, P17): At the bottom of the Centre Roll Hoop on the
Component Location Note
MoTeC M190 ECU Passenger Floor
MoTeC PDM32 Passenger Floor or Centre Console
MoTeC Lambda Passenger Floor To CAN module
MoTeC EDL3 or L180 Passenger Floor or Centre Console If used
Engine MAP Sensor Passenger Floor or front firewall (cabin side)
Crankcase Pressure Sensor Passenger Floor or front firewall (cabin side)
MoTeC ADL3 or C185 In front of the Driver above the steering column If used
MoTeC Display On the steering wheel or in front of the Driver above the steering column
If used
MoTeC SLM On the steering wheel or in front of the Driver above the steering column
MoTeC Beacon LH or RH side rear window attached to the ROPS LH or RH side depending on the Circuit
MoTeC VCS Passenger Floor Only one system (VCS or V2) is to be installed at any time.
MoTeC VCS Camera LH A pillar
MoTeC V2 LH A pillar
bf1 systems DigiTyre Lite TPMS ECU
Passenger Floor extending to left hand side Tunnel
© Supercars – 2020 Division “G” Page G35 of G54 ISSUED JANUARY 2020
passenger side. 15.1.8.3 Engine Loom Interface 1 (P6): On the Firewall, LHS of the transmission tunnel. 15.1.8.4 Engine Loom Interface 2 (P7): On the Firewall, LHS of the transmission tunnel. 15.1.8.5 Switch Panel (P11): On top of the transmission tunnel between the gear lever
and the engine firewall. This connector is not required if the PDM32 and the EDL3 are located in the Centre Console.
15.1.8.6 Torque Sensor (P57): LHS of the transmission tunnel in the vicinity of the gear lever and marked with a red heatshrink band.
G15.2 Engine Control
15.2.1 A Car must only be fitted with one (1) control ECU at all times while participating in any Event, ride day or Supercars Test day. Access to the control ECU must be provided to the CTM at any time upon request.
15.2.2 The control ECU must, at all times: 15.2.2.1 Not be disassembled or modified in any way and seals and markings must
remain intact and legible; and 15.2.2.2 Run only the approved DS2 version firmware and software as loaded into the
control ECU when supplied by Supercars; and 15.2.2.3 Exclusively control the spark and fuel settings of the engine; and 15.2.2.4 Only be connected to the loom as specified in the Supercars control wiring pinout
document. 15.2.3 The control ECU always remains the property of Supercars and must be returned to
Supercars upon the request of the CTM. 15.2.4 The control ECU must only be used for Supercars authorised activities. 15.2.5 The ignition timing of any engine must not vary by more than six (6) degrees while the
engine is above 4,000 rpm and above ten (10) percent throttle opening. G15.3 Control Actuators and Sensors
15.3.1 The table in Schedule G1.8 lists the sensors and actuators permitted to be connected to the control ECU and/or the data logging system.
15.3.2 The component required to perform each function must be as designated in the table. If the table does not specify a component for a particular function, then that component is free so long as its sole purpose is to perform the required function.
15.3.3 The Jacobs Design 3 force sensor is a CAN based sensor and if used replaces the three (3) analogue G force sensors listed in the table in Schedule G1.8.
15.3.4 A sensor must be connected as denoted in the “Destination” column in the table in Schedule G1.8. Each sensor that connects to the control ECU is a mandatory sensor. A sensor can be connected to the A/EDL using the method as stated in the “Destination” column.
15.3.5 Any sensors connected to the control ECU must correctly represent the measured parameter.
15.3.6 All permitted actuators and sensors must remain identifiable and unmodified, except as required to solely facilitate mounting. 15.3.6.1 It is permitted to enlarge the mounting hole of a coil unit for the sole purpose of
mounting using a proprietary anti-vibration mount. 15.3.7 All permitted actuators and sensors may be subjected to destructive testing. 15.3.8 The fuel pressure sensor must be located forward of the front firewall. 15.3.9 It is permitted to permanently attach wiring (pot) to the sensors listed in the table in Schedule
G1.8. All wiring connectors must respect the requirements of the control wiring pin out and connector specifications.
© Supercars – 2020 Division “G” Page G36 of G54 ISSUED JANUARY 2020
G15.4 Pit Lane Speed Limiter
15.4.1 The control ECU has an in-built Pit Lane speed limiter (“Limiter”), which must only operate
as follows:
15.4.1.1 must only be activated by a switch operated by the Driver.
15.4.1.2 The switch that is used to activate the Limiter must be connected exclusively to
the Limiter switch input of the control ECU and a fixed zero volt reference.
15.4.2 The Limiter must be activated at all times while a Car is moving in Pit Lane.
NOTE: Regardless of the Limiter, each Team always remains responsible for ensuring that
the Pit Lane speed limit is respected.
G15.5 Rain Light/Stall Light
15.5.1 The rain light/stall light must be fitted into the highest part of the rearward face of the boot
lid so that its face is at 90 degrees to the road surface.
15.5.2 The stall light which is amber in colour must flash if a Car stalls on the grid.
G15.6 Electronic Data – Logging, Display & Telemetry
15.6.1 Each Car must only be fitted with a control data recording unit.
15.6.2 Only the sensors indicated by a tick in the column A/EDL in the table in Schedule G1.8 are
permitted to be connected to the data logging system.
15.6.3 It is permitted to log the following functions of the systems listed below:
System Functionality permitted to be logged
Power Distribution Modules (see Note below)
Voltage, current draw temperature and diagnostics
NOTE: It is not permitted to use any of this information other than for diagnostic and
protection functions.
15.6.4 The sensors listed in the table in Schedule G1.8 are in addition to any switches, carrier
detect signal for telemetry or any sensors specifically required or approved by the CTM.
15.6.5 The data gathered from the sensors listed in Rule G15.3 and from the control ECU in the
Teams logging section may then be recorded, displayed or transmitted by any means
permitted by the Rules.
15.6.6 Data and system configurations may be requested by the CTM at any time and this request
will not be subject to protest or Appeal.
15.6.6.1 If MoTeC Display Creator is being used, the display project must be retrievable
from the device.
G15.7 Signals to/from Cars
15.7.1 At any time only the following signals may be sent to or from a Car:
Signal Send to Car Send from Car
Any signal exclusively for television Yes Yes
Telemetry (transmission of data) No Yes
Driver voice communication Yes Yes
Driver visual communication Yes Yes
Lap Beacon Yes No
© Supercars – 2020 Division “G” Page G37 of G54 ISSUED JANUARY 2020
G16. CAR EQUIPMENT
G16.1 Airjack
16.1.1 It is permitted to use a spacer of free design the sole purpose of which is to aid in the
securing of the airjack into the Chassis.
16.1.2 It is permitted to replace the airjack lower nut with a nut of an alternate design provided that
its sole purpose is to secure the airjack and/or protect the airjack thread.
© Supercars – 2020 Division “G” Page G38 of G54 ISSUED JANUARY 2020
SCHEDULE G1. CONTROL PARTS
The following list of Control Parts are as defined in the Rules. 1. Chassis
Part Name Part No or Drawing No Manufacturer Supplier
Airjacks CP3985 230EV CP3945-230EV
AP Racing Competition Friction
ROPS* SC Design Team
Machined Parts SC Design Team
Sheet Metal SC Design Team
*NOTE: It is permitted to alter the angle of the steering column mount bar V8SC-SM-02-A from
13 degrees stipulated in the Design to a minimum of 9 degrees.
The steering column mount support tube V8SC-SM-01-A may be extended or trimmed to
suit the angle of the steering column mount bar.
2. Suspension and Steering
Part Name Part No or Drawing No Manufacturer Supplier
Steering Column Clamp SBC 80-1 SBC 80-3*
Woodward Racer Industries
Steering Firewall Bearing SBC 6-2 Woodward Racer Industries
Steering Mounting Brackets MB178-40 Woodward Racer Industries
Steering Safety Column SCA700- Series Woodward Racer Industries
Suspension Tripod AR-3029 Modena Engineering Modena Engineering
Dampers TTX40 (ST design) Ohlins SCP
Dampers TTX40 MkII (ST design) Ohlins SCP
Damper Piston 06113-01 MkI & MkII Ohlins SCP
Damper Piston 06128-02 Blow off MkII w Bleed Ohlins SCP
Damper Piston 06234-01 HF MkII Ohlins SCP
Damper Piston 06234-10 Blow off MkII Ohlins SCP
Damper Piston 06234-11 HF+ Blow off.MkII Ohlins SCP
Dampers Formula Matrix Sachs** Triple Eight RE
Dampers Formula Matrix TRD Sachs** Triple Eight RE
Damper Piston 001706-999015 Dig/Dig Sachs Triple Eight RE
Damper Piston 001706-999016 Lin/Dig Sachs Triple Eight RE
Damper Piston 001706-999027 Lin/Dig Sachs Triple Eight RE
Damper Piston 001706-999056 Lin/Lin Sachs Triple Eight RE
Damper Piston 001706-999057 Lin/Lin w B Sachs Triple Eight RE
Damper Piston 001706-999073 Blow Off Sachs Triple Eight RE
Dampers S002-010 F/R Supashock Supashock
Damper Piston S002-001-226-0 Lin/Lin Supashock Supashock
Damper Piston S002-001-225-0 Lin/Dig Supashock Supashock
Damper Piston S002-001-224-0 Dig/Dig Supashock Supashock
© Supercars – 2020 Division “G” Page G39 of G54 ISSUED JANUARY 2020
NOTE: * For the SBC 80 – 3 if other than the top mounting hole is used, the material containing the
unused mounting holes may be removed.
** Teams using the Formula Matrix must utilise the adjuster block with Part No.
001706999019 or Part No. 001706000309.
3. Transaxle and Drivetrain
Part Name Part No or Drawing No Manufacturer Supplier
Transaxle Albins ST6 Albins Albins
Bellhousing Input Shaft V8SC-4-066 Albins Albins
Axle V8SC-4-065 Race Products
Modena Engineering Race Products
Modena Engineering
Axle Thrust Bearing V8SC-4-067 Race Products
Modena Engineering Race Products
Modena Engineering
Transaxle Cooler V8SC-7-001 (28028358) Team
Coupler 21138 Albins Albins
Centre Bearing 61908 Series 61909 Series
SKF
Centre Bearing Adaptor 14800 Albins Albins
Centre Bearing Mount* V8SC-4-058 Teams
Propshaft 19677 28067
Albins Albins
Centre Bearing 6908 Series NSK
Centre Bearing Adaptor AG-3168/69/70 Triple Eight RE Triple Eight RE
Centre Bearing Mount AG-3196 & AG-3315 Triple Eight RE Triple Eight RE
Propshaft AG-3031-A Triple Eight RE Triple Eight RE
Centre Bearing Adaptor** GRM-D-236-00 GRM GRM
Centre Bearing mount GRM-C-410-01 GRM GRM
Clutch CP8503 AP Racing Competition Friction
Clutch CP8033 AP Racing Competition Friction
Clutch OT II 7.25 Tilton Racer Industries
Clutch KKC 1803 Alcon Namsport
Clutch KKC 1843 Alcon Namsport
Clutch 883082001376 Sachs Triple Eight RE
Clutch 883082002297 Sachs Triple Eight RE
NOTE: * This is supplied as a Design.
** This utilises part of the Albins bearing adaptor 14800.
© Supercars – 2020 Division “G” Page G40 of G54 ISSUED JANUARY 2020
4. Wheels and Tyres
Part Name Part No or Drawing No Manufacturer Supplier
18” V8 Supercar Wheel Y063 81152-CL3 Rimstock Racer Industries
18” Tyre – Hard Dunlop Dunlop
18” Tyre – Soft Dunlop Dunlop
Wheel Nut V8SC-5-001 Team
5. Brake System
Part Name Part No or Drawing No Manufacturer Supplier
Brake Caliper-Front Right CP6268-2S7L:V8SC AP Racing Competition Friction
Brake Caliper-Front Left CP6268-3S7L:V8SC AP Racing Competition Friction
Brake Caliper-Rear Right CP6267-2S0L:V8SC AP Racing Competition Friction
Brake Caliper-Rear Left CP6267-3S0L:V8SC AP Racing Competition Friction
Brake Disc-Front Right CP8184-108GC:V8SC AP Racing Competition Friction
Brake Disc-Front Left CP8184-109GC:V8SC AP Racing Competition Friction
Brake Disc-Rear Right CP6372-102GE:V8SC AP Racing Competition Friction
Brake Disc-Rear Left CP6372-103GE:V8SC AP Racing Competition Friction
Brake Mounting Bell Rear CP2494-2547:V8SC AP Racing Competition Friction
Brake Bobbins CP4135-107FR AP Racing Competition Friction
Brake Pad Front CP6268D62 AP Racing Competition Friction
Brake Pad Rear CP6267D50 AP Racing Competition Friction
Pedal Box AS-3056 Triple Eight RE Triple Eight RE
Pedal Box-Alternate pedal AS 3112 Triple Eight RE Triple Eight RE
Master Cylinder- Front MAR 5200 Series* Alcon Namsport
CP7855 Series* AP Racing Competition Friction
Master Cylinder-Rear MAR 5200 Series* Alcon Namsport
CP7855 Series* AP Racing Competition Friction
Dry Brake Bleed Nipple (opt) CP6300-21 AP Racing AP Racing
Front Pad Option 1** PFC01 PFC Competition Friction
Front Pad Option 2** Project Mu H16-03 Project Mu Competition Friction
Front Pad Option 3** Circo MB2632-28-SCF Winmax Competition Friction
Rear Pad Option 1** PFC97 PFC Competition Friction
Rear Pad Option 2** Pagid RS4-4 Pagid Competition Friction
Rear Pad Option 3** Circo MB1648-25-SCR Winmax Competition Friction
NOTE: * Approved bore sizes only.
** It will be only permitted to modify the brake pad backing plate for ease of extraction and
replacement. Care should be taken not to remove the Supercars identification.
© Supercars – 2020 Division “G” Page G41 of G54 ISSUED JANUARY 2020
6. Fuel System
Part Name Part No or Drawing No Manufacturer Supplier
Fuel System V8SC CAD Team
Fuel Housing Assembly V8SC-8-10035 Premier Racer Industries
Fuel Bladder Housing V8SC-8-10030 Premier Racer Industries
Fuel Bladder Housing-Top Plate
V8SC-8-10031 Premier Racer Industries
Clamp Ring-LH V8SC-8-10040 Premier Racer Industries
Clamp Ring-RH V8SC-8-10039 Premier Racer Industries
Fuel Filler Pipes & Flanges COF-8-10020C COF-8-10023D COF-8-10024C
Team
Fuel & Vent Hoses 2.25” Bladder Material Hose Premier Racer Industries
Fuel Filter
F5003 WZ373
230606ERL & 230605ERL 601-010-06-08 602-010-06-08
Bosch Wesfill / Cooper
Earls Speedflow Speedflow
Fuel Regulator KFI 12-106
1729 Kinsler
Edelbrock
© Supercars – 2020 Division “G” Page G42 of G54 ISSUED JANUARY 2020
7. Electrical System
Part Name Part No Manufacturer Supplier Qty.
ECU 13190V – M190 Supercars ECU MoTeC Supercars 1
Data Logger*
18015V – Advanced Dash Logger 3 18016V – Enclosed Dash Logger 3 18033V & 18063V – C185 Colour Display Logger (max 250MB logging memory) 18035V – C187 Colour Display Logger (max 250MB logging memory) 18040V & 18047V – L180 Enclosed Logger (max 250MB logging memory)
MoTeC MoTeC
1 Or 1 Or 1
Or 1
Or 1
Display*
18015V – Advanced Data Logger 3 18027V – D153 Colour Mini Display 18028V – D175 Colour Display Module 18033V – C185 Colour Display Logger 18035V – C187 Colour Display Logger
MoTeC MoTeC
1 Or 1 Or 1 Or 1 Or 1
Power Distribution Module 14100V – PDM32 MoTeC MoTeC 1
Shift Light Module 18120V - SLM MoTeC MoTeC 2
LTCD 61301V – Bosch 61305V - NTK
MoTeC MoTeC 1
Or 1
Beacon Receiver 15512V MoTeC MoTeC 1
GPS Receiver 41304V – GPS 10Hz MoTeC MoTeC 1
Video Capture System 18207V – HD VCS 18210V – V2
MoTeC MoTeC 1
Or 1
Accident Data Recorder 18116V MoTeC MoTeC 1
Torque Sensor-Inner Housing
VESPER Magcanica Supercars 1
Wiring Pinout Document Control Wiring Pinout Supercars
Battery B128L MR-40
Braille MEGALife
Braille MEGALife
1
STC 61125 MoTeC MoTeC 1
TPMS ECU ** bf1systems DigiTyre Lite TPMS ECU bf1systems bf1systems 1
TPMS LF Trigger ** bf1systems DigiTyre LF Trigger bf1systems bf1systems 4
TPMS Antenna ** bf1systems DigiTyre Lite Antenna bf1systems bf1systems 2
TPMS Wheel Sensor ** bf1systems DigiTyre 14.7mbar/bit TPMS Wheel Sensor
bf1systems bf1systems 4
NOTE: * If the same model is used as a logger and a display, a second logger or display is not
permitted.
** The use of a Tyre Pressure Monitoring System is optional.
© Supercars – 2020 Division “G” Page G43 of G54 ISSUED JANUARY 2020
8. Sensors and Actuators
Sensor Qty Destination Manufacturer or
Restrictions Part #
Acceleration - Lateral 1 A/EDL
Acceleration - Longitudinal 1 A/EDL
Acceleration - Vertical 1 A/EDL
Coils 8 ECU
GM 12573190
GM 12611424
Delphi
A1569060400
(Mercedes-Benz)
GN10165-11B1
Denso 8687939 (Volvo)
Hanshan AIC-2402N
Fuel Flow 1 A/EDL
Floscan 200 series
Electronic
International Red Cube: FT-60
GPS - Data 1 ECU
A/EDL (via STC) Motec 41304V
Gyro/Compass/G force A/EDL Jacobs Design 3 Force
Injectors 8 ECU
Bosch 0 280 150 351 / 0
280 150 363
Siemens F111405
Bosch EV14 B280 436 748-01
(BOSCH)
Bosch 280158040 (Volvo)
Level - Engine Coolant 1 A/EDL
Level - Fuel 1 A/EDL Gill 1612-00-215-
275mm
Load - Gear Lever 1 ECU
A/EDL via CAN
Motorsport
Systems MS-GLC1
Motor - Drive by Wire Throttle ESD ECU
Position - Anti-Roll Bar 2 A/EDL
Position - Brake Balance Bar 1 A/EDL
Position - Camshaft 1 ECU
Honeywell 2AV Series
Honeywell 4AV Series
Siemens HKZ101 / HKZ121
Nanjing Huamin
Electronics HME101 / HME301
Bosch 0 232 103 079
0 232 103 111
Bosch
PG3.8
A0009050143
(AMG)
Omron E2E-X1R5E1
Motec 59110
Honeywell IGT101DC
Denso 30713370 (Volvo)
© Supercars – 2020 Division “G” Page G44 of G54 ISSUED JANUARY 2020
Sensor Qty Destination Manufacturer or
Restrictions Part #
Position - Crankshaft 1 ECU AB Electronic
A6429050000
(Mercedes-Benz)
Honeywell IGT101DC
Position – Crankshaft (con’t) 1 ECU
Delco 10456555
Denso 31331754 (Volvo)
Motec 59110
Position - Gear 1 ECU
A/EDL via CAN
Position - Throttle 1 ECU
A/EDL via CAN
Novatechnic RSC 2800-600
Series
Penny & Giles SRH 280P
Penny & Giles D46523/MK
Novatechnic SP2841S0002/SP2
8411002001
Variohm Euro X 28
Pressure - Brake Line 2 ECU
A/EDL via CAN
Pressure - Crankcase 1 ECU
A/EDL via CAN
Pressure - Engine Coolant 1 ECU
A/EDL via CAN
Pressure - Engine Oil 1 ECU
A/EDL via CAN
Pressure - Fuel 1 ECU
A/EDL via CAN
Bosch DS-K-TF A1561535028
(Mercedes-Benz)
Druck PWP4311
Honeywell MLH 100 - 250psi
Texas Instruments C63cp022 100 -
250psi
McLaren 0030330052002 -
10 Bar
Pressure - Manifold Air 1 ECU
A/EDL via CAN
Delphi 12219931
Fuji A0051535028
(Mercedes-Benz)
Pressure - Power Steering 1 ECU
A/EDL via CAN
Pressure - Transmission 1 A/EDL
Pump - Main Fuel 3 ECU Bosch 0 580 254 979
Pump - Lift Fuel 5 ECU Pierburg 7.21088.62
Rain Light 1-2 ECU GRME CK - LR - DC
Ratio – Oxygen 2 ECU via LTCD
Bosch LSU 4.9
Mercedes-Benz A0035427118
(Mercedes-Benz)
2 ECU via LTCD NTK LZA08
© Supercars – 2020 Division “G” Page G45 of G54 ISSUED JANUARY 2020
Sensor Qty Destination Manufacturer or
Restrictions Part #
Speed - Front Wheel 2 ECU
A/EDL via CAN
Speed - Rear Wheel 1 ECU
Temp – Front Brake Rotor* 2* A/EDL
Temp – Rear Brake Rotor 1 A/EDL
Temp - Cockpit 0-2 A/EDL
Temp - Driver Cooling System 0-2 A/EDL
Temp - Engine Air 1 ECU
A/EDL via CAN
Keystone
Thermetrics
2503 7388
2503 7334
Delco 2503 7388
Siemens NTC A6511530028
(Mercedes-Benz)
Bosch 0 280 130 039
0 280 130 085
Temp - Engine Coolant 1 ECU
A/EDL via CAN
Bosch 0 280 130 026
0 280 130 023
BERU NTC A0051532328
(Mercedes-Benz)
Denso 30646713 (Volvo)
Temp - Engine Oil 1 ECU
A/EDL via CAN
Temp - Fuel 1 ECU
A/EDL via CAN
Temp – Power Steering Oil 1 A/EDL
Temp - Transmission Oil 1 ECU
A/EDL via CAN Bosch 0 280 130 026
Torque - Engine 1 ECU
A/EDL via CAN
Magcanica
Supplied by
Supercars only
VESPER
Travel - Brake Master Cylinder 2 A/EDL External Linear
Travel - Steering 1 ECU
A/EDL via CAN
Travel - Suspension 4 A/EDL Linear or rotary
only
TPMS – Wheel Speed Trigger’s 4 Not applicable bf1systems DigiTyre LF Trigger
TPMS- Antenna 2 Not applicable bf1systems DigiTyre Lite
Antenna
TPMS- Tyre Pressure Sensors 4 ECU
A/EDL via CAN bf1systems
DigiTyre
14.7mbar/bit Wheel
Sensor
NOTE: * Only one (1) sensor is permitted per side.
© Supercars – 2020 Division “G” Page G46 of G54 ISSUED JANUARY 2020
9. Bodywork and General
Part Name Part No or Drawing No Manufacturer Supplier
Driver Side Impact Protection V8SC-11-022 (Schedule G3) Team
Driver Door Skin Layup V8SC-10-007 (Schedule G4) Team
Passenger, Rear Door Skin Layup & Front Guard Layup
V8SC-10-005 (Schedule G5) Team
Rear Quarter Panel Layup V8SC-10-003 (Schedule G6) Team
Front Door Window V8SC-10-006 (Schedule G7) Team
Rear Diffuser Absorber V8SC-11-020 Cellbond
CG Composites Cellbond
CG Composites
Fire Extinguisher System 104-225-002 105-001-004
Lifeline Racer Industries
10. Composites Components
Air conditioner mounts and covers Engine drive belt covers
Attachments to the ROPS for anti-side intrusion purposes
Engine management system mounting plate
BSi bootlid camera bracketry External fresh air duct
bf1systems TPMS trigger cover plate False floor (driver comfort)
Centre Console Foot rest
Coil mounts Fuel Injection trumpets
Cooling ducts Fuel tank covers (LHS & RHS)
Dashboard filler and airbag cover Identification light mount(s)
Data acquisition mounting plate Instrument fascia
Door trims Left hand mirror cover (where permitted)
Driver cooling systems Passenger floor (for Event rides only)
Dry break fuel fitting to Bodywork adaptor Rain light mount
Dry break fuel receiver/vent covers Rear window brake light housing
Electrical isolation switch mount Steering wheel switch mounts
Engine air box and inlet air ducting Wheel arch infill panel
Engine component heat shields Window bracing
© Supercars – 2020 Division “G” Page G47 of G54 ISSUED JANUARY 2020
SCHEDULE G2. CONTROL WHEEL NUT
NOTE: It will be permitted to remove 2 threads at the leading edge of the thread to reclaim the
wheel nut.
© Supercars – 2020 Division “G” Page G48 of G54 ISSUED JANUARY 2020
SCHEDULE G3. SIDE IMPACT PROTECTION STRUCTURE
© Supercars – 2020 Division “G” Page G49 of G54 ISSUED JANUARY 2020
SCHEDULE G4. DRIVER DOOR SKIN LAYUP
Composite Driver Door Skin Minimum Layup
1- Twaron T750/2 750gsm Plain weave 0/90deg 0.65mm thick all over 2- Twaron T750/2 750gsm Plain weave 45/45deg 0.65mm thick partial (central area) 3- Twaron T750/2 750gsm Plain weave 0/90deg 0.65mm thick all over
© Supercars – 2020 Division “G” Page G50 of G54 ISSUED JANUARY 2020
SCHEDULE G5. FRONT GUARD, LEFT FRONT DOOR SKIN, REAR DOOR SKIN LAYUP
© Supercars – 2020 Division “G” Page G51 of G54 ISSUED JANUARY 2020
SCHEDULE G6. REAR QUARTER PANEL LAYUP
© Supercars – 2020 Division “G” Page G52 of G54 ISSUED JANUARY 2020
SCHEDULE G7. FRONT DOOR WINDOW
© Supercars – 2020 Division “G” Page G53 of G54 ISSUED JANUARY 2020
SCHEDULE G8. LEG BRACE APPROVED MATERIAL LIST
• 80 GSM High Modulus Carbon
• 200 GSM 2x2 Carbon
• 180 GSM Hybrid Carbon / Kevlar
• 210 GSM Hybryd Carbon / Kevlar
• Core 3mm Rohacell
• Pet Core 6mm
• Using flame retardant Epoxy system The impact foam used must be:
• BSCI EIS W18 protected with a layer of Carbon-x fire protective cloth.
© Supercars – 2020 Division “G” Page G54 of G54 ISSUED JANUARY 2020
SCHEDULE G9. ENGINE LOG EXAMPLE
Engine Number Super Test
ESD Spec TEST KILOMETRES
EVENT KILOMETRES
CAR #
Ballast Positions
Total Ballast Mass
For any given part if there is more than one specification listed in the ESD please list
option used below.
Sealed Removed INSPECTED
Specified ESD Option
CHANGED KILOMETRES
Component Y INITIAL TOTAL
Cylinder Block 0
Crankshaft 0
Connecting Rods 0
Pistons 0
Gudgeon Pins 0
Camshaft Drive 0
Camshaft 0
Cylinder Heads 0
Roller Lifter 0
Pushrods 0
Rockers 0
Valve Springs 0
Valve Spring Retainers 0
Inlet Valves 0
Exhaust Valves 0
Inlet Manifold T/Body Assy 0
Oil pump 0
Harmonic Balancer 0
Sump 0
Flywheel 0
Cylinder Bore Coating
Comments Comments
Recommended