View
0
Download
0
Category
Preview:
Citation preview
DELTA MEMBRANE SYSTEMS LTD
DETAILING Date: July 2020
01992 523 523 | info@deltamembranes.com | www.deltamembranes.com
DETAILING02
CONTENTS
DELTA MEMBRANE SYSTEMS
A DELTA SOLUTION
SERVICES
TYPES AND GRADES OF WATERPROOFING
BRITISH STANDARDS
BS8102:2009 DESIGN PHILOSOPHY
EXAMPLES OF DEFECTS DUE TO POOR DETAILING
EXAMPLES OF GOOD DETAILING
DEFINITIONS OF DETAILING
ANTICIPATING DEFECTS
CONSTRUCTION JOINTS (INCLUDING MOVEMENT)
PIPE & SERVICE PENETRATIONS
CRACKS/HONEYCOMBING & CONCRETE DEFECTS
TIE BOLT HOLES
THRESHOLDS
UNDERPINNED DETAILS
FIXING THROUGH WATERPROOFING SYSTEMS
BEDDED STEEL BEAMS
ACTIVE LEAKS
ANCILLARY PRODUCTS TABLE
TECHNICAL DRAWINGS
03
04
05
06
07
08
010
011
012
014
016
022
024
028
030
032
034
036
038
041
042
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 03
DELTA MEMBRANE SYSTEMS
Delta Membrane Systems Limited is the leading Type C Cavity Drain Membrane manufacturer in the
United Kingdom. Our extensive range of waterproofing and damp proofing products are suitable for
basement drainage and structural waterproofing (both for new build and existing structures) and in flood
resilience.
Installing a Delta Membrane System offers complete protection to structures from ground water ingress
and contaminants. Our products comply with British Standard 8102:2009 and are BBA Certified. Our
dedicated technical team offer knowledge and experience in waterproofing design solutions, provide
on-site assistance and advice throughout a project.
• Type C Drainage Protection in accordance with BS 8102:2009
• BBA Approved
• Suitable for new, existing and retrofit basement projects
• Ability to easily deal with aggressive ground water conditions
• “Grade 3” performance level (no dampness or water penetration acceptable)
• “Air Gap” Technology
• A reversible system, which will not create damage to historical or heritage structures
• Flexibility to cope in structures where movement or vibration issues can be problematic
• Virgin high density polyethylene studded/moulded sheet (HDPE)
• Easily applied to a variety of different substrates
• An effective barrier to the transmission of salts, liquid water and water vapour
• Suitable for Flood Resilience
DETAILING04
A DELTA SOLUTION
BELOW GROUND WATERPROOFING SOLUTIONS FOR:
• Residential Buildings
• Commercial Buildings
• Retail Units and Warehouses
• Leisure Facilities
• Archives/Libraries/Vaults
• Hospitals
• Schools
• Underground Rail Stations and
Tunnelling
• Underground Car Parking areas
• Listed Buildings
• Heritage Buildings
• Insulated formwork Construction
BS 8102:2009 (Code of Practice for Protection of Below Ground Structures Against
Water from the Ground) recommends that every Design Team should incorporate a
Waterproofing Design Specialist.
Delta Membrane Systems Limited has a dedicated team of Waterproofing Design
Specialists. Our trusted Technical Team offer knowledge and experience and can provide
expertise in structural waterproofing. As a Waterproofing Specialist Manufacturer, we
work with architects, surveyors, contractors and engineers alike to provide a design
service which complies with BS 8102:2009 and offers the highest level of technical
expertise and assurance.
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 05
SERVICES
SERVICES
Delta Membrane Systems Limited provides a full range of waterproofing solutions suitable for all new, retrofit and refurbishment
construction. With over 125 years of manufacturing experience Delta is an impeccable partner on every project. Our skills have been
mastered through experience in the waterproofing industry. Delta’s trusted Technical Team will help from concept to completion.
Our hands-on approach and knowledge is what sets us apart.
DESIGN SUPPORT
• Architecture knowledge
• Concept and waterproofing
solutions
• Advice on design and best
practice
• Custom solutions, as each project
is unique in requirements
• Qualified CSSW staff (named on
the Waterproofing Design Reg-
ister)
SPECIFICATION SUPPORT
• Detailed drawings including CAD
• Watertight and locking down
structure concepts
• Specifications
• BIM
• NBS Plus
• RIBA Source
SITE SUPPORT
• Training and guidance offered at
every step
• Technical Team attendance at site
meetings
• Knowledge and experience
• Troubleshooting solutions
DETAILING06
TYPES AND GRADES OF WATERPROOFING
There are many different approaches to structural waterproofing. The construction methods will in part contribute to the specification
of types of waterproofing systems and may also determine the overall structural waterproofing strategy.
Structural waterproofing falls into 3 categories:
Type A – Barrier Protection
Type B - Structurally Integral Protection
Type C – Drained Protection
With 3 grades:
Grade 1 – Some water seepage and damp are tolerable depending on the intended use
Grade 2 – No water penetration is acceptable
Grade 3 – No dampness or water penetration is acceptable and dehumidification
Residential/Commercial Basements
Hospitals
Infrastructure Projects
Car Parks
Schools
Railway and Tunnelling
Museums and Heritage
Hotels
Libraries
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 07
BRITISH STANDARDS
BRITISH STANDARDS
Established in 1901 the BSI Group (formerly the Engineering Standards
Committee), sought to standardise the types of steel manufactured in
Great Britain in order to assist with competitiveness and efficiency.
Over decades these standards have been developed to cover numerous
aspects of the engineering/building sector including engineering
methodologies, quality, safety, systems and security.
BS 8102:2009
British Standard 8102 ‘Code of practice for protection of below ground
structures against water from the ground’ was first publicised in 1990
with the second edition being publicised in November 2009. BS
8102:2009 supersedes BS 8102:1990 and CP102.
BS 8102 is a standard designed to protect the consumer. BS 8102 has
been formulated to ensure the correct waterproofing solution has been
selected and adhered to during the build process.
BS 8102 covers (but is not limited to):
• Cavity drain
• Cut-off wall
• Damp area
• Embedded retainer wall
• Ground barrier
• Loading coat
• Perched water table
• Seepage
• Tanking
• Barrier protection
• Vapour
• Waterproofing
• Waterproofing barrier
• Waterproofing system
• Water resistance
• Waterstop
• Water vapour
• Water vapour resistance
NHBC CHAPTER 5.4 OFFERS A CHOICE OF STRATEGIES:• Design Standards
• Statutory Requirements
• Load-bearing Structure
• Principles of Design
• Structural Deck
• Thermal Insultation and Vapour Control Layers
• Waterproofing and surface finishes
• Rainwater Drainage
• Guarding to Balconies
• Access for Maintenance
• Provision of Information
DETAILING08
BS8102:2009 DESIGN PHILOSOPHY
BS8102:2009 Code of Practice for the protection of below ground structures against water from the ground, provides guidance on the
methods which should be adopted to deal with and prevent the entry of water from the ground into a structure that is below ground level.
It is widely referred to and used in basement waterproofing with reference to:
• Adoption of a design team
• Water table classification
• Defects and remedial measures
Our Design and Build Philosophy is quality driven, working with architects and trades alike, putting at the forefront construction considerations
to ensure buildability, functionality, and maintainability. The result of this single approach is a consistent, complete, and quality design that
is hard to equal.
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 09
BS8102:2009 DESIGN PHILOSOPHY
In a world of hasty construction that can at times neglect attention to detail, we take pride in our passion to improve standards within the
industry to develop solutions and successful installations which offer a life cycle to equal and beyond current expectations.
Delta’s designs focus on a life-cycle oriented design philosophy, addressing life-cycle concepts and methods, deterioration and damage
evaluation, life-cycle performance indicators, inspection and maintenance procedures all implemented in design practice. We work with our
customers to establish a robust functioning design, this fine-tuning during the design processes reduces project failure.
Whether designing a waterproofing solution for a new home or reviving and modernizing an existing space, our designs are built to last and
to be maintainable. By embracing the design-build model, we save our clients stress, time, and money; we can remove the bidding step from
the construction process and work with our own well-established team of Registered Installers.
Our design philosophy embraces innovation and creating solutions that minimize client risk, foster collaboration, and partnership, and
ultimately delivers the client with a waterproofing system which will be resist to the passage of water. Well compacted concrete is inherently
water resistant and with enough depth can effortlessly block water ingress from structures below ground. But why do so many concrete
structures leak? It is not the concrete, which is leaking but areas such as service penetrations, cracks/joints/ducts which are not adequately
waterproofed which allow for water ingress. Much of the failure associated with structural waterproofing is attributed to insufficient
consideration of details within the waterproofing design.
DETAILING010
EXAMPLES OF DEFECTS DUE TO POOR DETAILING
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 011
EXAMPLES OF GOOD DETAILING
DETAILING012
Active Leak
Water penetration through a structure/substrate at a current time.
Capillary break
A hydrophobic material or non-porous material (such as plastic, metal or glass) or gap between parallel layers of material (often
less than 1/16” or 1.5 mm) sufficient to stop capillary action.
Cold Joint
A cold joint is the boundary between concrete steps for example the wall/floor joint.
Construction Joint
A construction joint is a concrete joint formed in-situ that is used when a new section of concrete is poured adjacent to another
concrete section that has already set or interfacing between masonry or other building materials.
A construction joint is essentially a planned crack and a Crack is an unplanned joint.
Contraction Joint
A contraction joint is formed, sawed, or tooled groove in a concrete structure to create a weakened plane to regulate the location
of cracking resulting from the dimensional change of different parts of the structure.
Crack Repair
Methods for repairing cracked walls/floors and ensuring that they are watertight.
Dummy Joint
A dummy joint is a predetermined breaking point. Usually a groove cut into the top half of a concrete slab, sometimes packed
with filler, to form a line where the slab can crack with only minimum damage.
Expansion Joint
An expansion joint is a planned joint which is designed to allow two sections of concrete or masonry to expand and contract.
Floor/Wall Junction
An area where the wall meets the floor/slab in construction.
DEFINITIONS OF DETAILING
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 013
Firebreak
Products used to provide fire protection by the sealing of linear gaps, service penetrations, movement joints and other necessary
openings in fire separating wall and floors.
Load-Bearing Wall
A load-bearing wall or bearing wall is a wall that is an active structural element of a building, it bears the weight of the elements
above the wall. Load-bearing walls are one of the earliest forms of construction.
Kicker
A Kicker is a small (5-15cm) step/concrete up stand cast above the slab/foundation/floor to position the coordinates for a column
or wall formwork for the next construction level.
Movement Joint
A movement joint is a planned joint which is designed to permit relative movement caused by expansion due to changes of
temperature or moisture.
Pressed Joint
A pressed joint allows for the transfer of pressure, transverse displacement can be avoided with an interlocking geometry.
Reveals
Reveals are the distance or measurement from the face of a door/window out to the face of the frame on the push side.
Service Penetrations
Service penetrations are created using a cast-in-place sleeve, in a wall or floor assembly, for the purpose of accommodating the
passage of a mechanical, electrical or structural service.
Settlement Joint
Settlement joints are joint between adjacent parts of a building, structure, or concrete that permits the adjoining masses to settle
at slightly different rates.
Unplanned Movement Joint
An unplanned movement joint can be the cause of shrinkage, creep, thermal movement or to accommodate movement with
temperature changes.
DEFINITIONS OF DETAILING
DETAILING014
Consideration to how defects maybe created (from human error to design fault) and the subsequence’s of these defects in how they
effect a structure is a great starting block to focus on the positives of how to avoid the creation of defects.
A construction defect is generally a deficiency in the design or the construction. A small construction defect can be destructive and
lead to damage. However, it is not always possible to detect this defect until after construction. While some defects are obvious
from the onset, most are not detected until years after finishing the structure, in the case of waterproofing, when water ingress
occurs.
Many causes combined within a project may lead to defects. However, there are some common factors that are counted as the main
contributors to waterproofing defects on site. For example, inexperienced workmanship, inaccurate measurement, inferior materials
and ineffective communication.
Are zero defects achievable?
Is it impossible to factor out defects in construction?
We believe that the waterproofing sector can achieve near zero defects, by adopting successful waterproofing techniques along
with correct built philosophy and utilising best practices will influence the success of a project.
It is crucial that all involved in a project should care and that a structural waterproofing consultant should be appointed at the onset
of a project.
A structural waterproofing consultant is a specialist usually appointed in a project to provide information and guidance relating to
the design, installation and maintenance of a structure’s waterproofing system.
Risk management is a particularly important part of the structural waterproofing consultant’s role and the structural waterproofing
consultant will have a wealth of knowledge regarding anticipating defects.
The benefits of appointing a structural waterproofing consultant is that they are specially qualified and experienced in creating
solutions to prevent water ingress and can work within any constraints within a project.
With all types Delta waterproofing systems, it is recommended that contractors, such as Delta Registered Installers who are trained
and experienced in the Delta systems are used for installation.
ANTICIPATING DEFECTS
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 015
WHAT ARE COMMON DEFECTS IN BELOW GROUND STRUCTURES?
Common defects within structural waterproofing systems are
estimated to cost £25 million per annum in the United Kingdom.
Full site investigations are important when mitigating and reducing
risk in waterproofing design. The results will have a bearing not
only on the design but on the waterproofing system itself. Whilst
findings of a site investigation are often seen as conclusive, it
needs to be remembered that this is just a ‘snapshot in time’. It
should be assumed that water will come to bear against the full
height of the below ground structure at some time in its life.
The system designed maybe acceptable at the time of construction
meeting the ‘snapshot in time’ investigations, however this system
may not be adequate for environmental changes of the future.
Natural causes for waterproofing failure:
• Changes in water tables
• Changes in hydrostatic pressure
• Thermal changes
• Dynamic Movement
• Heave
• Subsidence
• Clay soils
• Changes in environment
• Stress
• Changes in ground drainage
• Structural stability
Human error causes for waterproofing failure:
• Lack of maintenance
• Poor installation
• Inappropriate materials installed
• Incorrect/wrong choice systems specified
• Bad placement of reinforcement
• Poorly compacted concrete/ Honeycombing of
concrete
• Poor detailing
• Poor design
• Damage to the waterproofing system
• Cracks to concrete
• Concrete defects at joints
ANTICIPATING DEFECTS
DETAILING016
Generally, a construction joint is where two placements of concrete meet, typically daywork joints in concrete, where one pour ends and
another begins. These joints are placed at regular intervals to prevent the future development of cracks. The design of the joint is important
for the overall design to function of a structure. Design and construction should be kept as simple as possible. When waterproofing joints,
an important consideration is that the material is suitable for the expected amount of movement within the structure.
Types of movement:
• Shrinkage – Initially rapid, less severe as the concrete ages
• Creep – A phenomenon which causes a redistribution of stress away from points of intensity
• Thermal movement – Expansion and contraction of the structure with temperature changes
The success of joint waterproofing starts at the conception stage. The product used to waterproof joints must offer a permanent and flexible
seal, allowing for movement without increasing damage in the event of movement. Construction Joint waterproofing can be incorporated at
the design stage or retrofitted for failed systems.
CONSTRUCTION JOINTS (including Movement)
QUELLBAND (Water Bar)
Koster Quellband is used as a waterstop in concrete construction
joints. The robust strip is simply nailed onto an existing joint face
before the consequent concrete pour. Any leakage through the joint
activates the Quellband.
• Alkalinity activated - stops premature swelling on contact with
water
• Easy application
• No special tools are needed
• Permanent seal of the joint after swelling - fills all voids and
cracks in the concrete
• Easy to use, non-sticky surface even at high temperatures
• No material fatigue - swells even after years
Associated Products:
• Koster Quellband (Water Bar)
• Koster IN 5
• Koster Flex Tape 20 & 30
• Koster KB Pox Adhesive
• Koster FS-H
• Koster FS-V
• Koster FS Primer 2C
• Koster PU 907
• Koster NB 1
• Koster Repair Mortar Plus
• Injection Tube (Hose)
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 017
CONSTRUCTION JOINTS
KOSTER IN 5
Koster IN 5 is a solvent-free, low viscosity, 2 Component polyurethane
for permanently and elastically injecting, filling, and sealing cracks
and construction joints. Koster IN 5 does not react aggressively when
coming into contact with steel or iron, enabling a corrosion protection
to be achieved. Due to its slow reaction, the material can be processed
for up to 4 hours.
• Permanently seals and bridges cracks, joints
• Does not react aggressively with steel or iron
• Easy, seamless application
• Fast curing
• Suitable for new construction and repair on existing structures
KOSTER JOINT TAPE 20 & 30
Koster Joint Tape 20 (Elastic sealing tape for waterproofing joints and
irregular cracks, (1 mm x 200 mm) and Joint Tape 30 (Elastic sealing
tape for waterproofing joints and irregular cracks, (1 mm x 300 mm) are
thermoplastic tapes for sealing and bridging expansion and dilation
joints (up to 12cm) and broad, irregular cracks.
• Thermoplastic tapes
• Suitable for sealing and bridging expansion and dilation joints
• Suitable for sealing irregular cracks
• UV resistant
• Highly elastic and can withstand extreme movements of joints
• Used in conjunction with Koster KB Pox adhesive
DETAILING018
CONSTRUCTION JOINTS
KOSTER KB POX ADHESIVE
Koster KB Pox Adhesive is a high performing, 2 component epoxy
adhesive specifically produced for securing Koster Joint Tape 20 and
Joint Tape 30.
• 100% solid and is solvent free
• Suitable for dry, moist or wet substrates
• Thixotropic material creates immense adhesive strength
• Suitable for concrete, mortar, metal, wood & a wide range of
other building materials
• Robust strength promptly
• Suitable for vertical and horizontal application
KOSTER FS-H
Koster Joint Sealant FS-H is a polysulphide-based elastic, pourable
joint sealant for sealing joints in horizontal areas. When fully cured, has
a high mechanical load capacity, good resistance to water, sea water,
salt solutions, benzenes and mineral oils. It is root resistant, does not
rot and it has exceptionally good retraction properties.
• Suitable for construction and movement joints
• High ability to cope with high mechanical stresses
• Permanently and elastically seal horizontal joints
• Pourable/self- levelling joint sealant
• Available on Delta “How To” Video Guides
• Good resistance to water
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 019
CONSTRUCTION JOINTS
KOSTER FS-V
Koster Joint Sealant FS-V is a flexible stiff/creamy polysulphide joint
sealant. When fully cured, is a rubbery elastic sealant with a high
mechanical load capacity, good resistance to water, sea water, salt
solutions, benzenes and mineral oils; it is root resistant, does not rot
and it has very good retraction capabilities.
• Can be used to permanently, and, elastically seal vertical joints
• High mechanical load capacity
• Easy application
• Available on Delta “How To” Video Guides
• Good resistance to water, salt solutions, benzenes & mineral oils
• Great retraction capabilities
KOSTER FS PRIMER 2C
Koster FS Primer 2C is a bonding agent for Koster Sealants FS-H &
FS-V. FS Primer 2C is a 2 component, brush applied transparent fast
curing primer.
• The two components are mixed, until homogenous consistency
is achieved
• This Primer is Brush applied to joint prior to the installation of
FS-H or FS-V
• If the substrate is highly porous a second coat of primer will be
required
• Joint should be free from grease, dirt and oils prior to use of FS
Primer 2C
• Curing time Approx. 30 minutes
• Application temperature 5 °C – + 30 °C
DETAILING020
CONSTRUCTION JOINTS
KOSTER PU 907
Koster PU 907 is designed for civil and industrial movement,
expansion, control and dilatation joints in architectural and heavy
construction. Koster PU 907 is a highly elastic, one component, low
modulus polyurethane joint sealant. This remarkable sealant can be
used for between concrete, mortar, brickwork, natural and synthetic
stone, metal, steel, aluminium, wood, ceramic tiles and rigid plastics.
.
• Cures with moisture to create a flexible sealant for overpainting
once cured
• Highly thixotropic with positive workability
• Excellent adhesion to typical construction materials
• Easy application using a silicone gun
• Seamless Application
• Non-Sagging
KOSTER NB 1
Koster NB 1 is a crystallizing mineral waterproofing slurry system for sealing
against pressurized water (> 13 bar). Containing crystallising and capillary-
plugging agents, protection of cementitious renders or concrete with cracks
due to shrinkage and against water infiltration. Whilst offering protection of
structures with an inadequate layer of concrete over the reinforcement rods
against the penetration of aggressive elements.
• Flexible material
• Protection of cementitious renders or concrete with cracks due
to shrinkage and against water infiltration
• Protection of concrete pillars and beams against the penetration
of carbon dioxide
• Flexible protection layer of new concrete structures or repaired
structures.
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 021
CONSTRUCTION JOINTS
INJECTION TUBE (HOSE) SYSTEM
Injection hoses are installed in the middle of the wall in lengths of
approximately 10 to 15 m. The minimum concrete cover must be 8
to 10 cm. The injection hoses must be in continuous contact with the
concrete substrate. The sealing caps of the holder boxes must be flush
with the surface of the formwork and remain accessible. No injection
should take place within the first 28 days of the concrete being cast.
The injection is carried out using customary low-pressure injection
systems in conjunction with suitable injection ports, (packers). When
using a single component pump, no moisture may meet the injection
material during the application. The injection hose is filled until material
comes out of the other hose end. That end of the hose is then sealed
and material is injected until the gauge pressure on the injection pump
remains constant. Make sure to protect the surrounding work area
from injection resin that may be discharged from the wall, packers, drill
holes, etc. Do not stand directly behind the packers during injection.
DETAILING022
Building services allow the structure to operate and do what it was mean to do, structures require pipes, ducts and cables to pass through it
in unseen voids through walls and floors. During the design stage, a Waterproofing Design Consultant should consider how these services
are going to enter the structure and creatively apply design principles to design a continuous waterproofing system.
From drainage pipes, gas mains to electrical wires all will need appropriate consideration to avoid dire consequences of waterproofing fail.
BS8102:2009 sets out many types of sealing solutions across all types (A, B & C) of waterproofing systems. The type of sealing system must
be suitable for the waterproofing solution. From new to retrofit design principles will include products which offer a failsafe continuous wa-
terproofing solution.
PIPE & SERVICE PENETRATIONS
KOSTER KB FLEX 200
Koster KB-Flex 200 is a permanent plastic sealing compound ideal
for sealing pipe and cable penetrations, cavities and for custom detail
waterproofing solutions against moisture and pressurized water.
• Waterproof sealing compound
• Watertight finish
• Ideal solution for sealing pipe and cable penetrations
• Does not dry out
• Can be applied to dry, moist or wet substrates
• Immediate functionality
• Can be used internally and externally on concrete, brickwork,
blockwork or masonry
• Non shrink
Associated Products:
• Koster Quellband (Water Bar)
• Koster KB Flex
• Puddle Flanges
• Koster Repair Mortar Plus
• Delta Cornerstrip
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 023
PIPE & SERVICE PENETRATIONS
DELTA PUDDLE FLANGES
A puddle flange offers an effective solution against water penetration
around service pipes. Incorporating a puddle flange into designs
ensures a watertight seal is offered where pipes pass through concrete
structures (i.e. the walls of any structure below groundwater level and
in flood resilience designs).
Pipes passing through concrete will not bond to the concrete and
water can pass long the external surface of the pipe, a puddle flange
will act as a barrier to this flow. The seal body within the puddle
flange is compressed during the concrete pouring process, should
the concrete shrink during curing the rubber relaxes and maintains
a seal against any flow path. A puddle flange is recommended for
use around any pipe penetration in a below ground structure. Puddle
flanges are available in various sizes from 32mm up to 160mm.
DETAILING024
Every waterproofing design should allow for defects owing to poor workmanship, inappropriate use of materials and defects owing to
specific properties within the materials used to create the structure. Waterproofing systems for below ground structures are opposed with
stringent requirements regarding durability, exposure and stress conditions.
To establish a waterproof structure when using concrete, its essential to follow good concrete practices. The importance in ensuring
concrete is fully compacted and cured should be a fundamental element.
Project failure can happen to any project. There are an infinite number of reasons for failure. In most cases, failure is controllable. There are
many common pitfalls when it comes to designing a robust waterproofing system. Products do not fail! When failures occur, it is due to the
design and build philosophy not being correct. The devil is in the detail – all waterproofing elements must be considered at the construction
design stage to be durable and effective.
CRACKS/HONEYCOMBING & CONCRETE DEFECTS
KOSTER POLYSIL TG 500
Koster Polysil TG 500 – is a deeply penetrating primer for damp, salt-
containing substrates and an anti-lime treatment for new concrete
which also acts as a liquid hardener for sealing slurries. Polysil TG 500
will not only reduce the amount of free lime leaching but will also
improve the water resistance of the basement structure by absorption
into the structure and locking in the free lime.
• ‘anti lime’ coating product specially blended with Polymers and
silicates
• Brush or Spray application
• Can be used to strengthen and to protect mineral substrates and
to reduce their absorbency, even of such problematic building
materials as sandstone
• Decreases the danger of new development of salt efflorescence,
free lime egress, and raises the resistance of mineral substrates
to freezing and thawing
• Can also be used to harden sealing slurries
• Can be used as a surface primer for Koster waterproof Coating
Associated Products:
• Koster Polysil TG 500
• Koster Repair Mortar Plus
• Koster Betomor Multi A
• Koster Z1 & Z2
• Koster Sewer & Shaft Mortar
• Koster Repair Mortar NC
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 025
CRACKS/HONEYCOMBING & CONCRETE DEFECTS
KOSTER BETOMOR MULTI A
Koster Betomor Multi A is a shrink free, waterproof, light mortar with
exceptionally low density for repairing and reprofiling concrete and
screed surfaces.
• For filling, repairing and reprofiling of fractured or broken
concrete areas
• Low Density
• Should be applied in 2 coats
• Shrink-free
• Easy application
• Allows for a continuous system
KOSTER Z1 & Z2
Koster Z1 and Z2 are polymer modified, mineral corrosion protection
coatings for reinforcement steel. Before use reinforcement steel must
be cleaned before this bonding agent is applied.
• Brush applied to cleaned steel
• Koster Z1 is grey in colour for visual control of application
• Koster Z2 is red in colour for visual control of the application
• Fast curing time
• Continuous system
• Works with Repair Mortar NC
DETAILING026
KOSTER SEWER & SHAFT MORTAR
Koster Sewer and Shaft Mortar is a watertight, fast curing and fast
setting restoration mortar for sewers and shafts. Sewer and Shaft
Mortar is fibre reinforced and develops a high compressive strength.
Sewer and Shaft Mortar can be applied below the waterline even under
flowing water. Sewer and Shaft Mortar can be used for the watertight
repair, renovation and touch ups of sewer and shaft systems, as well as
for levelling and filling of breakouts up to 3 cm per layer.
• Excellent Workability
• Suitable for relevant repair and touch up of sewers and shafts
• Easy, seamless application
• Useable on all stable, hard mineral substrates
• Substrate must be open pored
• High compressive strength
KOSTER REPAIR MORTAR NC
Koster Repair Mortar NC is a fibre reinforced repair, concrete replacement
and finishing mortar with high chemical and mechanical resilience. It has a
high adhesion to old and new mineral building material substrates. Koster
Repair Mortar NC can be used for structurally relevant repair and touch up
of voids, and for levelling of concrete defects.
• Can be applied to all concrete substrates
• High chemical and mechanical resistance
• High compressive strength
• Easy application
• Continuous application
CRACKS/HONEYCOMBING & CONCRETE DEFECTS
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 027
CRACKS/HONEYCOMBING & CONCRETE DEFECTS
DETAILING028
Casting concrete is a crucial task in construction and requires great planning and accuracy, in addition to a proper execution sequence.
Tie bolt holes (shutter bolt holes) are often forgotten when it comes to continuous waterproofing systems. Used when pouring reinforced
concrete these bolts, which keep shuttering in place, will often need waterproofing retrospectively once the concrete has cured.
It is fundamental that all waterproofing elements of a structure are communicated with all parties throughout the construction process. For
this reason, the waterproof design should take into consideration the construction stages and timing between them to ensure a continuous
waterproofing system is installed/applied during the correct stages.
TIE BOLT HOLES
Associated Products:
• Koster Repair Mortar Plus
• Koster KB Flex 200
REPAIR MORTAR PLUS
Koster Repair Mortar Plus is a watertight, fast setting, slightly expanding
repair mortar with excellent adhesion (even to old building material
substrates). With the addition of Koster SB Bonding Emulsion, it can be
used as a PCC (polymer-modified cement concrete) mortar.
• Watertight (Positive and negative side waterproofing)
• Fast Setting (Seamless, easy application)
• Slightly expanding
• Excellent adhesion
• Can be applied to all mineral substrates
• Suitable for watertight repairs and touch ups to substrates
• Can be used internally and externally on concrete, brickwork,
blockwork or masonry
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 029
TIE BOLT HOLES
KOSTER KB FLEX 200
Koster KB-Flex 200 is a permanent plastic sealing compound ideal
for sealing pipe and cable penetrations, cavities and for custom detail
waterproofing solutions against moisture and pressurized water.
• Waterproof sealing compound
• Watertight finish
• Ideal solution for sealing pipe and cable penetrations
• Does not dry out
• Can be applied to dry, moist or wet substrates
• Immediate functionality
• Can be used internally and externally on concrete, brickwork,
blockwork or masonry
DELTA HIGH PERFORMANCE DPC
Delta High Performance DPC is a high performance polymeric
material designed to suit all applications. Whether as a dpc at ground
level, or for use as a fully designed cavity tray system, Delta DPC is
designed to withstand the heaviest of loadings and is fully compatible
with all materials it is likely to come into contact with during the normal
course of construction and satisfies all the requirements as laid down
by current British Standards.
Delta High Performance DPC is available in various thicknesses either
for use in buildings up to four storeys or for use in buildings in excess
of four storeys.
• Suitable for use as a DPC in all types of building construction
• Can be used in vertical, horizontal, stepped and cavity tray
application
• Available in various thicknessess
• Excellent tear resistance under high compressive loads
• Low permeability to Radon
• Both faces feature a non-slip profile to ensure optimum mortar
adhesion
• Bitumen-compatible, rot-proof and UV-stabilized
• Highly flexible even at low temperatures, so that no cracks will
occur in the material
DETAILING030
BS8102:2009 ‘Code of Practice for the Protection of Below Ground Structures against Water from the Ground’, provides excellent guidance
on design principles to ensure waterproofing systems are adopted to deal with and prevent the entry of water from the ground into a
structure at below ground level. This guidance document is widely referred to and used throughout the waterproofing industry.
It should be assumed that water will come to bear against the full height of the below ground structure at some time in its life cycle. It is
important to carry the waterproofing system through beneath thresholds, rather than just terminating the waterproofing at the threshold.
Also, to ensure good seals between the waterproofing system and the threshold below the plate (or timber seal), particularly where fixings
are likely to penetrate the waterproof membrane.
THRESHOLDS
Associated Products:
• Delta High Performance DPC
• Koster NB 1
• Delta Cornerstrip
• Koster Repair Mortar Plus
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 031
THREHOLDS
DETAILING032
BS 8004:2015+A1:2020, gives recommendations for the design, construction, testing, monitoring and maintenance of foundations in
accordance with BS EN 1997. The foundation types covered include spread foundations, pile foundations (including helical pile foundations)
and underpinning.
The term “Underpinning” means a solid foundation laid below ground level to support or strengthen a building. This process can sometimes
be more economical, due to land prices or otherwise, to work on an existing structure’s foundation than it would be to build a new one.
There are several tried and tested methods to select from for how to achieve water tightness of these most critical of junctures below ground
levels, which are notorious passages for water ingress when not adequately, or robustly detailed.
UNDERPINNED DETAILS
KOSTER WATERSTOP
Koster Waterstop is a fast curing, expanding plug and repair mortar.
Waterstop can be used to seal water leakages in concrete, masonry
and natural stone structures quickly. The material can also be used
to form fillets which are subject to pressurised water, to seal slotted
walls, manholes, cable and pipe penetrations, and to subsequently
seal damaged pipe joints in canal construction even if they are
exposed to pressurised water.
• Repairs to concrete and screeds
• Construction joint detailing/leak stopping
• Filling tie bolt holes in concrete construction
• Detailing to dry pack joints
• Watertight
• Ability to stop active leaks
Associated Products:
• Koster Waterstop
• Koster Polysil TG 500
• Koster Repair Mortar Plus
• Koster SB Bonding Emulsion
• Koster NB 1
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 033
UNDERPINNED DETAILS
KOSTER SB BONDING EMULSION
Elasticizing synthetic-dispersion for universal use in mortars,
plasters, sealing slurries and concrete. Koster SB Bonding Emulsion
is a universally usable synthetic liquid for all cementitious mortars,
plasters and sealing slurries. Koster SB Bonding Emulsion is solvent,
plasticizer and filler-free. When added to mineral based systems, the
synthetic liquid increases elasticity and flexibility and reduces water
absorption. Koster SB Bonding Emulsion is waterproof which means
that after it is very cured it can neither be washed or rained off.
• Positive and negative side waterproofing against pressurized
water
• Can be used in all cases in which a good bond between
mortars, plasters, sealing slurries, concrete and existing mineral
substrates
• As an additive to mineral systems, the synthetic additive
causes a strong increase in flexibility and elasticity and at the
same time a reduction of the water absorption
• Improves the application properties and workability of fresh
mortars
• Suitable for new construction and repair on existing structures
DETAILING034
It is essential that care should be taken if fixing through waterproofing systems. Not using suitable fixings or fixing through waterproofing
systems without ensuring the fixings are waterproofed will compromise the continuous system and potentially could lead to a failed system.
Consideration must be made to ensure the continuity of fixings and repair of the same. They should be checked for compatibility with the
waterproofing layer.
When selecting the correct waterproofing solutions, ensure you choose your construction materials and supply chains carefully and opt for
one that will serve you well.
For a continuous solution ensure:
• A reliable waterproofing system is selected
• The system is maintainable post installation
• That the system is compatible with the type of construction
• Simple and safe application
FIXING THROUGH WATERPROOFING SYSTEMS
KOSTER KB FIX 5
Koster KB Fix 5 is an extremely fast setting waterproof and weatherproof
mortar for swift installations. KB Fix 5 swiftly fills holes and cracks in
plaster and masonry and can be used for anchoring wall anchors,
anchor fittings, brackets of roof gutters and down pipes, handrails,
grates, radiators as well as for swift repairs at home, for sealing pipe
penetrations in connection with Koster KB Flex 200.
• Fast setting
• Anchoring System
• Fast setting waterproof and weatherproof mortar
• Suitable for internal and external waterproofing
Associated Products:
• Koster KB Fix 5
• Koster Repair Mortar Plus
• Delta Fix Adhesive
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 035
FIXING THROUGH WATERPROOFING SYSTEMS
DELTA FIX ADHESIVE
Delta Fix Adhesive is formulated as an adhesive for bonding &
anchoring most building materials e.g. brick, stone, steel, mortar &
timber. Suitable for fixing bolts and penetrations through waterproof
coatings to provide a waterproof seal. Once cured Delta Fix Adhesive
creates a strong stress free joint regardless of the surrounding
environment.
• Delta Fix Adhesive is colour coded for visual assurance that the
two components are fully mixed
• Solvent free
• Thixotropic
• Cures in cold, damp conditions
• Resin anchor system for fixings into masonry and concrete
structures
DETAILING036
Steel beams or RSJ’s are normally used in mid to long span situations to support heavy structural elements such as podium decks or load
bearing walls. The waterproofing of steel beams is usually restricted to sealing the ends, where they may be embedded or supported within
basement retaining walls or upon structural piers or recessed pad stones, thereby potentially “piercing” the internal basement waterproofing
system.
The internal waterproofing of the recessed “pocket” upon which the beam end will rest can be achieved using Type A cementitious barrier
products such as NB1 Grey Repair Mortar Plus or KB Flex 200 will act to reduce the likelihood of leakage in this particular area. The
installation of the specially pre-formed rubber “boot” within the pocket will ensure watertight barrier around the beam and it will provide a
ready flange around the pocket edge to which the Type C internal cavity drainage membrane can be sealed, so providing continuity of the
internal waterproofing system around the beam.
BEDDED STEEL BEAMS
DELTA JOIST BOOTS (TOP HATS)
Delta Joist Boots (Top Hats) are manufactured from high performance
flexible dpc.
• Suitable for continuous waterproofing
• Suitable for new build and refurbishments
• Easy to install
• Available to suit any size
• Fast delivery
Associated Products:
• Delta Joist Boots (Top Hats)
• Koster Repair Mortar Plus
• Koster NB 1
• Delta Cornerstrip
• Koster Bitumen Primer
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 037
BEDDED STEEL BEAMS
DELTA CORNERSTRIP
Delta Corner Strip is a waterproof, firm and lasting single-sided sealing
tape applied to seal wall to floor junctions and internal penetrations
through the Delta membrane system. Delta Corner Strip creates a
vapour seal making it an ideal solution for patch repairs and detailing
around service penetrations (150mm x 20 m).
• Used for abutting joints
• For repairs or where membranes have been cut to enable them
to overlap
• Excellent for sealing and repair
• Creates a vapour seal
• Suitable for sealing service penetrations
• Suitable for fixing plugs to membranes
DETAILING038
Sources of external water such as a high or rising water table, river, extreme weather, tidal changes, poorly drained soil, defective drains can
all result in water penetration of a structure at below ground level.
This penetrating water may have enough pressure and strength to ingress a structure, even one which is presumed to have been adequately
waterproofed. Basements and other below ground structures can leak both during and after construction. Any construction below ground
will always be subject to groundwater. Groundwater will try and seep through cracks and joints in all construction. Joints (from movement to
floor/wall junctions) will always require attention when waterproofing and these are common pitfalls in project fails.
Remedial work to active leaks in construction, which is exposed, are relatively easy to find and fix. If the construction is not exposed and
finishing’s are in place, these leaks are difficult to find but not impossible. Use of a thermal imaging cameras/borescopes/moisture meters
or visual inspections are usually enough to locate these leaks.
ACTIVE LEAKS
KOSTER 2 IN 1
Koster 2 IN 1 stops active leaks and seals cracks and construction joints
permanently and elastically. It can be injected in dry and wet cracks.
The material can also be used for filling of voids. 2 IN 1 is a water
reactive elastic PU-injection resin for single and two stage injection of
dry and water bearing cracks and joints.
When Koster 2 IN 1 resin comes into contact with water, it reacts to
form a highly elastic foam. When 2 IN 1 resin is injected under dry
conditions, it reacts to form a solid body elastic resin. Koster 2 IN 1
remains permanently elastic after reacting.
• Used in conjunction with Type A & Type B Waterproofing systems
• Stops active leaks and seals crack and construction joints
permanently
• Easy application
• Seamless application
• Fast curing
• Applied on dry or water bearing cracks and joints
Associated Products:
• Koster 2 in 1
• Koster in 7
• Koster Waterstop
• Koster KD Blitz
• Koster Repair Mortar Plus
• Koster KB Fix 5
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 039
ACTIVE LEAKS
KOSTER IN 7
Koster IN 7 is a single component viscoplastic PU-injection foam for
waterproofing of cracks in concrete and masonry. It stops leakages
even under pressurized water. IN 7 is applied in a single step without
necessity of subsequent injection with a solid body resin.
• Permanently seals and bridges cracks, joints and restores
structural integrity
• Solvent-free
• Resistant to hydrolysis.
• Stops leakages even under pressurized water
• Easy, Seamless application
• Suitable for new construction and repair on existing structures
KOSTER KD BLITZ
Koster KD 2 Blitz powder instantly stops active leaks (from dripping
to flowing), whilst offering versatility in both non-pressurized and
pressurized waterproofing from positive and negative side substrates.
Koster KD 2 Blitz powder is a unique component of the Koster KD
System (KD 1 Base, KD 2 Blitz powder and KD 3 Sealer) which can be
used either as part of the KD System or standalone in sealing and/or
closing cracks prior to the use of injection resins.
• Fast Curing Time
• Highly Reactive
• Suitable for waterproofing positive and negative side of
substrates
• Suitable for active leaks (pressurized and non-pressurized)
• Suitable for sealing and closing cracks prior to use of injection
resins
• Instantly stops active leaks
DETAILING040
TABLE
Waterstop KD System KD Blitz Koster NB 1 DPC Joint Tape 20 Resin Injection Systems 2 IN 1
*With SB Bonding Emulsion
Construction Joint
* (if Leaking) *(if Leaking)
Contraction Joint * * (if Leaking)
Crack Repair
Dummy Joint
Expansion Joint * * (if Leaking)
Floor/Wall Junction *Honeycombed Concrete
* (if Leaking)
Kicker * *
Movement Joint * * (if Leaking)
Pressed Joint * * (if Leaking)
Reveals *Service Penetrations
Settlement Joint *(if Leaking) *(if Leaking)
Unplanned movement joint * *(if Leaking) *(if Leaking)
*
* *
* *
Active Leak
Capillary break
Cold Joint
* * *
Table 1
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 041
TABLE
FSV FSH PU 907 Repair Mortar Plus Betamour Multi A KB Fix 5 Puddle Flange KB Flex 200 Quellband
Construction Joint * * * * *
Contraction Joint * * *
Crack Repair * * *
Dummy Joint
Expansion Joint * * *Floor/Wall Junction *Honeycombed Concrete * * *
Kicker
Movement Joint * * *
Pressed Joint * * *
Reveals
Service Penetrations * * *
Settlement Joint * * * *Unplanned movement joint * *
Active Leak
Capillary break
Cold Joint
Table 2
DETAILING042
TECHNICAL DRAWINGS
To view our full range of technical drawings, please visit our website on www.deltamembranes.com/technical-categories/tech-
nical-drawings/or contact our technical department on 01992 523 523.
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 043
TECHNICAL DRAWINGS
DETAILING044
TECHNICAL DRAWINGS
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 045
TECHNICAL DRAWINGS
DETAILING046
TECHNICAL DRAWINGS
0101992 523 523 | info@deltamembranes.com | www.deltamembranes.com 047
TECHNICAL DRAWINGS
Registered Offices:
Delta House, Merlin Way, North Weald, Epping, Essex, CM16 6HR
01992 523 523 | info@deltamembranes.com | www.deltamembranes.com DMS/D/1/2020/1
© 2020 - Deltamembranes - All Rights Reserved
Recommended