View
7
Download
0
Category
Preview:
Citation preview
Dell SonicWALL SOHO Quick Start Guide
Regulatory Model Number: APL31-0B9
1 Check package contents Verify your package has the following contents:
Dell SonicWALL SOHO appliance
Ethernet cable
Standard power adaptor
Standard power cord
Quick Start Guide NOTE: The included power cord is approved for use only in specific countries or regions. Before using a power cord, verify that it is rated and approved for use in your location.
o
SonicWALL SOHO Dr1011. II
1 Test Fast blinking is initializing Slow blinking is SafeMode
Bottom - 1 Gbps when lit
USB port
Power
IIIIMPUIIP11111
Console Port
XO LAN Port
X1 WAN Port
SOHO front and back panels Front Panel
Top - 10/100 Mbps when lit
Back Panel
SDHC Slot For future use
X2/X3/X4 Configurable ports
I Power
2 Power on Connect the power adaptor to the appliance and to the power cable. Plug the power cable into an appropriate outlet (100-240 volts).
lAlit..4,3v :0
The SOHO appliance powers on and the Test LED blinks during the boot sequence.
e 2 mmn
A CAUTION: Only use the included power adaptor with this appliance. Do not use a power adaptor that is damaged or from another appliance.
TIP: Your computer should be using DHCP IP addressing.
In the window that opens, click on the word here in the Une that says, "To launch the Dell SonicWALL Setup Wizard, click here."
1~.50 U NETVVORK SECURITY APPLIANCF
To launch the DELL SonicWALL Setup Wizard, dick here.
you wish to log directly into the DELL SonicWALL management interface, chdc here.
The SonicOS Startup Wizard opens.
SettiCWAU. Welcome to the SonicOS Setup Wizard
Die SontOS Setup Wired is clestned In eme ere 'That confltraten of yes Cal SorinedeLL sea applance. lime Setup %Mord ni Pulunallady siert the firSt tme tu comed to the SonicOS management interface
Clame Passnord the semp gozare' does nat sitie or mocIfy any system mtengs date berree te
Chute1St Zone PM step, so you an soft* restart dunng asy stop, tt toral seto conants oí
Configure 3Gingotedan fox stenslo secure Watt and LAN network cumectons.
WAK Neisverk Mude Someta help toolbox are avedable f each step in the Seto Vd. neo net
botos by hovenng your mouse over the rally field. Use the next buttn and le WAN Settings back botan to taverse ti-embale setn sequence.
tal Potro'
UN~ Setásas
Pala Ossignment
Summer"
Done
o
3 Connect the interfaces Connect the WAN interface (X1) to your Internet connection using a standard Ethernet cable.
Connect the LAN interface (XO) to your computer using a standard Ethernet cable.
Run the Setup Wizard Navigate to https://192.168.168.168 on your Web browser.
http://192.168.168.168/
Register product Point your browser to the appliance LAN IP address (default https://192.168.168.168) and log in using the administrator credentials.
Click Register on the System > Status page under Security Services.
Security Services
Nodes/Usere 5 Modes (O in use)
SSL VPN Nodes/Usere 2 Nades (OS, use)
Your DELL SonicWALL is not registered. Click here to Reoister your DE1L SonicWALL.
To manually register, remember the following informaban: Serial Numben CnFtiF44F3CEIC Authentication Code 95VC-57113
and go to the oaL SonicW/11 Web site.
YOU Mi be given a registraban code, which you shotid enter below:
Update
o TIP: Registering the appliance from SonicOS requires that DNS Server settings are configured on the WAN (X1) interface.
Log in using your MySonicWALL account name and password. If you do not have a MySonicWALL account, click the Create MySonicWALL account link to create an account.
SOnkWALL Change Administrator Password
Chane Password
Chame Tenle Zar<
Ccefilse 3G/C/Modem
WAN Nehvoá Mide
WAN Settngs
LAN Settngs
LAN DHCP Senna
Porto Assignmeit
Siannatv
l'eme selecta stcn2Pass~d. A stron9 Password shedd be a casebinaton of nimbas and letlers up to 32 diaracters long.
Cid Password:
New Pasman':
Conf.-N:
< Back Next > Cancel
Click Next and enter he administrator credentials to change the password, if you wish.
NOTE: The default administrator credentials are Username: admin Password: password
Click Next and follow the prompts on each screen to configure any of following screens:
Change Time Zone Configure Modular Device Type WAN Network Mode WAN Network Mode: NAT Enabled LAN Settings LAN DHCP Settings Ports Assigment Summary Setup Wizard Complete
o
Example—On the WAN Network Mode page, select the mode that you use to connect to your Internet Service Provider (ISP). All modes except Router-based offer automatic WAN IP addressing (DHCP).
WAN Network Mode
Select the method used to connect to your Ingsrnet Service Provider (ISP):
Note: When the firewali was powered oil, it did not detect a PPPoE or DHCP Server on the WAN.
Router-based Connections - Use a Static IP address or a range of IP addresses.
O C_able/Modem-based Connections - Use DliCP assigned dynamic IP addresses.
DSI Connections - Use PPPoE for ISP ckent authentication software.
VPN Connections - Use PPTP for encrypted connections.
Exarnple—To configure LAN DHCP Settings, setect Enable DHCP Server on LAN and enter the LAN address range in the appropriate fields.
LAN DHCP Settings Cenfigure yute OFICP seres-.
Enable Ele Server al LAN
Enter a rant of D'aclárese:e for yaz neenak devion on the LAN. lbs address rant met be It the sane subnet as the 013.15cricWALL Web Managerieht adEress.LOS SorkWAIIN defatt gateway ateas, current set to: 192.168.168.168/155255255.0.
The rangebebw a/ready erists. Yen may dwee ithere if yourrish.
Address Range: 192 168 1681 ti, 192168168 167
0 10
The Summary page displays your configuration. Click Apply, then close the Wizard.
DELL SonicWALL Configuration Summary
WAN Interface - NAT rrith DHCP Client Enabled VEAN settngs sil he set autornabab.
N'oh, NEWS; No Mogo [erg: No
3G/ 4Giliariem Device - Nene
LANInterface - Enabled IP Address: 192.168.168.158 SubnetMask: 255.255.255.0 [NEP Enabled: 192.160.168.1- 192.168.168.167
PerISX0:1ANAssignment )(1: WAN X2e(n: LAN
To use these SetbngS, chck APPIY.
Bac Ap p Cancel
Licensesji
License Management
MySonrcVVALL usernamejemail:
Passaord:
Subo*
FCMCIOt vour Username or Password?
Create MySonicWALL account.
MySonicWALL gets the necessary information directly from the SOHO appliance. When finished, you will see a message that registration has been completed.
ucensesi License Management
Thank you for regstenng las product. Relataban completed successfuliy.
Continue
01 NOTE: Your appliance must be registered to download the latest firmware.
6 Get the latest firmware In a Web browser, navigate to http://www.mysonicwall.com
Click Downloads and select SOHO Firmware from the Software Type drop-down list.
Click the link for the firmware you want and save the file to a location on your computer.
On the SOHO appliance, navigate to the System > Settings page and click the Upload New Firmware button.
Click the Browse button to navigate to and select the firmware you just downloaded.
O souowou Neboork Seanty Appkante
Upload nrniwa re
%etc UploatIng no,/ frmate va pomo-de ala eocl'Eng Uplooded Rine image.
You can get dic latest flrmware al wvoromvsorievatcon.Dovolload it lo yaz bcoi dsk, and ten upload te snxr Del SajCWAs usng lbs (febo.
Use the brome bulbo, to find lbe Serenare lie you %vont to wioacl.Fonnwe have a 0. exiorzion of sg, e.g•, svcfpromare.slo.
ofoo. tie (tomare o momea, you wa rekzea lo the syste. > setungs par .11.2re roo a set the mor Uploacled Frmware image. There you may select Ole fimmare paga from Mich to booL
Firmware Re: Brows e._ )
upiono Cancel
Click Upload and wait for the upload to complete.
In the Firmware Management Table, click the Boot icon for your new firmware.
Recommended