View
227
Download
1
Category
Preview:
Citation preview
1 of 31 © Boardworks Ltd 2011
Current, Voltage and Resistance
2 of 31 © Boardworks Ltd 2011
3 of 31 © Boardworks Ltd 2011
How do different components affect the flow of current?
What obstacles affect the flow of current?
4 of 31 © Boardworks Ltd 2011
What affects the size of the current?
Current can be changed by increasing or decreasing
the voltage of the circuit.
Current is a measure of the rate of flow of electric charge
through a circuit. A large current means a faster rate of flow.
Components in a circuit may
reduce the size of the current.
This is called resistance.
All wires and components
resist current.
Resistance is a measure of
how hard it is for electrons to
move in an electrical circuit.
5 of 31 © Boardworks Ltd 2011
Resistance simulation
6 of 31 © Boardworks Ltd 2011
What is a resistor?
A resistor is a component designed to reduce the current.
A variable resistor has a resistance that can be changed.
A fixed resistor has a resistance that remains the same.
Many domestic appliances use
resistance to transfer electrical
energy to heat and light energy.
As current is passed through
the metal element in this kettle,
resistance causes the metal to
get hot and so boils the water.
Resistors are also used to control
the current in electric circuits.
7 of 31 © Boardworks Ltd 2011
8 of 31 © Boardworks Ltd 2011
Set up this circuit with a resistor and a variable resistor.
Slowly adjust the variable resistor,
increasing the voltage by 0.5V at a
time and record the current for
each setting.
Plot a current-voltage graph of the results.
V
A
How can resistance be investigated?
voltage (V)
0.0
0.6
1.1
1.8
2.5
3.0
3.5
4.2
0.0
0.5
1.0
1.5
2.5
2.0
3.0
3.5
current (A)
9 of 31 © Boardworks Ltd 2011
Investigating current and voltage
10 of 31 © Boardworks Ltd 2011
Current–voltage graphs
11 of 31 © Boardworks Ltd 2011
Plotting current–voltage
results for nichrome and
copper wires on the same
graph gives straight lines
with different gradients.
At the same voltage, a
copper wire allows a larger
current than a nichrome
wire of the same size.
nichrome
copper
This means that the copper wire has a lower resistance
than the nichrome wire. What does the gradient tell you
about resistance?
cu
rren
t (A
)
voltage (V)
The steeper the gradient of a current–voltage
graph, the lower the resistance of the wire.
Is resistance the same in all wires?
12 of 31 © Boardworks Ltd 2011
Current–voltage graphs
13 of 31 © Boardworks Ltd 2011
14 of 31 © Boardworks Ltd 2011
Resistance is a measure of
how hard it is for electrons to
move in an electrical circuit.
The connection between current,
voltage and resistance was
discovered in 1827 by Georg
Ohm, a German physics and
maths teacher.
The formula V = I × R is known as
Ohm’s Law. It was such an
important discovery that the unit
of resistance is called the ohm.
It is represented by the symbol W.
The irresistible Georg Ohm
15 of 31 © Boardworks Ltd 2011
What are the units of voltage, current and resistance?
Ohm’s law is usually written as:
Voltage is measured in volts (V).
Current is measured in amps (A).
Resistance is measured in ohms (W).
This formula can also be written as:
voltage = current × resistance
V = I × R
resistance =
R =
voltage
current
What is Ohm’s law?
V
I
16 of 31 © Boardworks Ltd 2011
What does Ohm’s law show?
What do the different arrangements of Ohm’s law show
about the links between current, voltage and resistance?
V = I × R
R = V / I
I = V / R
As voltage increases, the current increases.
Voltage and current are proportional, while
the resistance remains constant.
Voltage and current are proportional, so
the resistance of a material is constant, as
long as the temperature does not change.
If voltage is constant, then current
decreases as resistance increases.
17 of 31 © Boardworks Ltd 2011
A formula triangle helps you to rearrange a formula.
The formula triangle for V = IR is shown below.
Cover up the quantity that you have to work out.
This gives the formula needed.
So to find current (I),
cover up I……which gives
the formula…
I =V
R
×
Resistance formula triangle
18 of 31 © Boardworks Ltd 2011
A filament bulb has a current
of 0.2A running through it,
with a potential difference of
5V across it.
V = IR
Calculating the resistance of a bulb
What is the resistance of
the filament in the bulb?
= 5V
0.2A
V
I
= 25 W
In calculations like this one,
the resistance of the
connecting wires is usually
small enough to be ignored.
R =
19 of 31 © Boardworks Ltd 2011
Resistance calculations
20 of 31 © Boardworks Ltd 2011
Finding the resistance of a component
21 of 31 © Boardworks Ltd 2011
22 of 31 © Boardworks Ltd 2011
The resistance of a wire depends on several factors:
material
length
thickness
temperature
What experiments could be used to test how length
and thickness affect resistance?
What affects resistance?
23 of 31 © Boardworks Ltd 2011
Resistance and length
24 of 31 © Boardworks Ltd 2011
How does length affect resistance?
When the length of the wire increases, resistance increases.
The table shows the resistance of different lengths of wire.
What general pattern do these results show?
length (cm)
5
10
20
voltage (V)
current (A)
resistance (W)
2.6
2.9
3.0
5.0
4.3
2.1
0.52
0.67
1.48
Resistance is caused by electrons colliding with metal ions.
When the length of the wire is increased, the electrons
have to travel further, so more collisions will occur.
25 of 31 © Boardworks Ltd 2011
Resistance and thickness
26 of 31 © Boardworks Ltd 2011
How does thickness affect resistance?
When the thickness of wire increases, resistance decreases.
The table shows the resistance of different thicknesses
of wire. What general pattern do these results show?
thickness (mm)
1
2
4
voltage (V)
current (A)
resistance (W)
3.0
2.9
2.6
2.1
4.3
5.0
1.48
0.67
0.52
Increasing the thickness of a wire increases the surface
area that the electrons can flow through. This decreases
the chance of collisions with metal ions.
27 of 31 © Boardworks Ltd 2011
How does temperature affect resistance?
If a component obeys Ohm’s law, then decreasing the
temperature decreases the resistance of the material.
A superconductor is a
material that conducts
electricity with very little
resistance at very low
temperatures.
This is because the positively charged ions in the metal do
not vibrate as fast, and the electrons can flow more easily.
Superconductors can be
used to make very fast
circuits and to make
magnets levitate.
28 of 31 © Boardworks Ltd 2011
Resistance – true or false?
29 of 31 © Boardworks Ltd 2011
30 of 31 © Boardworks Ltd 2011
Glossary
31 of 31 © Boardworks Ltd 2011
Multiple-choice quiz
Recommended