View
223
Download
0
Category
Preview:
Citation preview
Chlorination / DeChlorinationProcedures
-A New Twist to an Old Technology-
Robert Gordhamer
Measurement Technologies, Inc.
Redmond, Washington
Chlorination / Dechlorination
• Field Chlorination– Forms of chlorine– Reducing the amount of chlorine– Methods of chlorination
• Field Dechlorination– Discharge requirements– Dechlorination chemicals– Methods of dechlorination
FIELD CHLORINATION
• AWWA/ANSI C651-05– Disinfecting Water Mains
• First standard approved Sept. 30, 1947• Latest revision June 1, 2005
– Standards are reviewed every five years.– AWWA standards describe minimum
requirements AND is not a SPECIFICATION.
Forms of Chlorine
*It is recommended that you follow the current AWWA C651 specification with the following modifications.
Sodium hypochlorite (NaOCl) solution...
Liquid chlorine (Cl2)...
Calcium hypochlorite (Ca(OCl)2) granules or tablets...
FIELD CHLORINATION
• Liquid Chlorine– Least expensive with the highest danger.– Requires specially trained treatment crews.– Requires safety equipment for the operator
and all other personnel at the site.– Requires containment container for cylinder.
FIELD CHLORINATION
• Calcium Hypochlorite (HTH)– Available in two forms
• Tablets• Granular
– Contains approximately 65% available chlorine.
– Placed in pipeline during construction.– Recommended to be used in pipe sizes to 24”
diameter.
FIELD CHLORINATION
• Sodium Hypochlorite– Contains between 5% to 15% available
chlorine. (12.5% typical)– Available in 1 qt. to 55 gallon containers.– Must be stored properly to prevent
deterioration.– Must be NSF 60, household bleach is not an
acceptable chlorine.
What determines how hot you cook the line …
• Chlorine Residual Level…– The specifier determines the chlorine
residual level the line should be targeted for?
– Did your crews let dirt get into the pipeline during the installation?
– Did you not seal the pipeline at night? Could there be animals inside the line?
Disinfecting Water MainsBasic Disinfection Procedure
1. Inspect materials to insure their integrity.2. Preventing contaminating materials from
entering the watermain.3. Remove, by flushing those materials that
may have entered the line.4. Pressure test new installation.5. Chlorinating the new installation
cont.
Disinfecting Water MainsBasic Disinfection Procedure
6. Document that an adequate level of chlorine contacted each pipe.
7. Flushing the highly chlorinated water from the main.
8. Determining the bacteriological quality by laboratory test after disinfection.
9. Final connection of the approved new water main to the active distribution system.
By using aModified Continuous-Feed
method.
• Mixes the chlorine solution with every gallon of water that is filling your new system. This will insure total contact at the desired chlorine residual level.
The lateral by-pass venturi works by combining two principles together…
• 2” Mainline orifice.
Plus three additional orifice insert…
And,
Side view -Showing the mainline orifice ring.
By inserting the smaller orifices you can control your discharge rate OR increase by-pass pressure to insure a full vacuum is achieved.
This orifice directs part of the water flow into the lateral by-pass venturi.Flow direction
The Pros & Cons ofVenturi / Orifice designs…
• The smaller the opening , the quicker you get a vacuum, HOWEVER, you take away high flow performance.
• The larger the opening, the higher the flow must be before a vacuum is achieved. This takes away low end performance.
Lateral By-Pass VenturiDesign with Mainline Orifice…
• FEATURES:– Full vacuum throughout entire flow
range.– Wide range of FLOW.– Controllability of feed solution.
Lateral By-Pass VenturiDesign with Mainline Orifice…
• CONSISTENT FEED RATE:– ONE GALLON per minute, FROM
START TO FINISH.– Feed control valve allows for proper
balancing of feed solution.– Gives operator the ability to make feed
solution strength based on flow.
Chlorinating Set-Up
Source Hydrant
No outside power required when you use a venturi style device.
Enter point
Testing for CRL
• Locate sampling points, having the first point within ten feet of the entry point.
• Number of sampling points to be determined by the size of the project.
Set-up Discharge area
• You will need to discharge water from the system during the chlorinating operation.
• Some of this water will have a chlorine residual level that needs to be neutralized.
Procedure for chlorinating the system
• Adjust feed control valve to full open position.• Turn on the water supply to start filling.• Test chlorine residual level at a sample point
within ten feet of the entry point.• Follow Engineer’s specifications on the chlorine
residual level.• Take test samples at selected sites throughout
the project.• Adjust the control valve to increase or decrease
the amount of chlorine entering the system.
LiabilityIf you allow chlorinated water to be discharge into the environment and you have not enforced your state regulations, YOU will share in the responsibility. OR, in other words the fine.This will be true for the consulting engineer, the owner and the person or company that discharges the chlorinated water.
EPA has set guidelines…
• The US-EPA has a recommended set of guidelines.– Each state has adapted there own standards.– Some states, have even broken it down into
regions.• However, all states have discharge limits
on chlorine or chloraminated water.• AWWA is developing a new dechlorination
standard.
And, it’s good for the Environment…
• Even a trace of chlorine will kill fish.
• Your discharge water effects the beginning of the food chain.
Washington, Oregon and Idaho’sRequirements
• Regulation Standard:– State Controlled
• DISCHARGE LIMITS:– Fresh Water CMC (Acute)
• 19 ug/L– Fresh Water CCC (Chronic)
• 11 ug/L
mg/L vs. ug/L
• mg/L means milligrams per liter or parts per million (PPM).
1 mg/L = 1 PPM
• ug/L means micrograms per liter or parts per billion (PPB).
1 ug/L = 1 PPB
Convertug/L (PPB) to mg/L (PPM)
• To convert micrograms per liter to milligrams per liter, divide by 1000.
• 11 ug/L divided by 1000 = 0.011 mg/L• 19 ug/L divided by 1000 = 0.019 mg/L
• .8 mg/L multiplied by 1000 = 800 ug/L PPB
What you should know…
So, you are going to specify DECHLORINATION.
There are many different styles of dechlorination devices, so be sure, that if you specify a device that it works at the chlorine residual levels that
will be encountered.
LiabilityConsideration should be given to specifying
only the performance that is needed and let the contractor determine what
equipment to use to achieve the chlorine residual level specified for the discharge.
This way you do not assume liability on what equipment was used.
Dechlorination
• Two major methods of Dechlorination– Non-Chemical Dechlorination
• Only to be used for low chlorinated water.• Chloraminated water can take 3 – 4 times longer to
decay the chlorine residual.– Chemical Dechlorination
• Faster and more predictable method.• Available in solid, liquid and gaseous forms.• Works well with chloraminated water.
Non-Chemical Methodsfor Dechlorination
• Holding Tanks or Ponds• Land Applications• Groundwater recharge• Releases though hay bales• Discharge into Strom Sewers• Discharges into Sanitary Sewers
Chemical methodsfor Dechlorination
Types of Chemical Dechlorination
• Drip – style devices• Injection Pumps• Passive device• Vacuum - Induced
Forms of Dechlorination Equipment
• Passive– A device which requires that the water
discharge to make contact with the dechlorination chemical.
• Vacuum-induced– Any device that produces a vacuum and
provides a means of controlling the flow of dechlorination chemical.
Dechlorination Chemicals
Common chemicals used in field dechlorinationSodium Sulfite
Sodium ThiosulfateSodium Bisulfite
Ascorbic acidSodium Ascorbate
Calcium Thiosulfate
Why should you use only environmentally safe chemicals
• We are neutralizing the chlorine to protect aquatic life.
• We have to be aware of pH.• NO effect dissolved oxygen in the water.• Safe for humans to handle.• Easier shipping and handling of freight.
What chemicals are safe for aquatic life?
• Calcium Thiosulfate (Domestic)– Liquid solution
• Ascorbic acid (Imported)– Granular or tablet form
• Sodium Ascorbate (Imported)– Granular form only
Cost comparison of chemicals that are safe for aquatic life?
• Calcium Thiosulfate (Domestic)– Low cost
• Ascorbic acid (Imported)– Granular – three times the cost– Tablet – five times the cost
• Sodium Ascorbate (Imported)– Granular – over 6 times the cost
Basic Dechlorination Procedure
• The selected dechlorination process must be able to neutralize the chlorine to levels below 0.01 mg/l.
• Testing needs to be done at the point of discharge, the point you lose control of the water flow.
• Spread dechlorination chemical in the path of the discharge water to insure that the initial water will make contact with the chemical.
Basic Dechlorination Procedure
• Make sure that either your feed solution or your tablet chamber has the proper amount of chemical to handle the chlorine residual to be neutralized.
• Start your discharge and check your chlorine residual at the discharge point.
• Make any adjustments that may require proper neutralization of chlorine.
Basic Dechlorination Procedure
• If using a manufactured device follow the manufacturers directions.
• Monitor chlorine residual at per determine times during the discharge and record in log book.
• When you achieve the desired chlorine residual level in your discharge water, stop flushing.
Required Equipment
• Proper dechlorination device that will neutralize the chlorine residual.
• The proper amount of dechlorination chemical.
• Proper chlorine test equipment that will measure to 0.01 mg/l this means TEN PARTS PER BILLION.
Set-up Discharge area
• You will need to discharge water from the system during the flushing operation.
• Make sure that the area will handle the amount of the discharge.
• Store chemicals properly.• Set-up additional
monitoringequipment.
Set-up• Determine where the device will be located in
relationship to the discharge point from the outlet of the system.
• It is preferred to have the discharge point away from the device.
Testing your discharge
• If your test shows no chlorine, turn feed solution control valve down until you show a sign of chlorine in your discharge.
• Then open feed solution control valve a slight amount to balance feed solution strength to chlorine residual discharge.
• As you are flushing you may test your incoming residual level of chlorine by drawing a sample from the make-up water valve.
Recommended