Chapter 6Based on Design & Analysis of Experiments 7E 2009 Montgomery 1 Design and Analysis of...

Chapter 6 Based on Design & Analysis of Experiments 7E 2009 Montgomery

Design and Analysis of Engineering Experiments

Ali Ahmad, PhD

Chapter 6 Design & Analysis of Experiments 7E 2009 Montgomery

Design of Engineering Experiments Two-Level Factorial Designs

• Special case of the general factorial design; k factors, all at two levels

• The two levels are usually called low and high (they could be either quantitative or qualitative)

• Very widely used in industrial experimentation• Form a basic “building block” for other very useful

experimental designs (DNA)• Special (short-cut) methods for analysis• We will make use of Minitab

The Simplest Case: The 22

“-” and “+” denote the low and high levels of a factor, respectively

• Low and high are arbitrary terms

• Geometrically, the four runs form the corners of a square

• Factors can be quantitative or qualitative, although their treatment in the final model will be different

Chemical Process Example

A = reactant concentration, B = catalyst amount, y = recovery

Analysis Procedure for a Factorial Design

• Estimate factor effects• Formulate model

– With replication, use full model– With an unreplicated design, use normal probability

plots• Statistical testing (ANOVA)• Refine the model• Analyze residuals (graphical)• Interpret results

Estimation of Factor Effects

2 2[ (1)]

2 2[ (1) ]

ab a b

n nab a b

ab b a

n nab b a

ab a bAB

n nab a b

See textbook, pg. 209-210 For manual calculations

The effect estimates are: A = 8.33, B = -5.00, AB = 1.67

Practical interpretation?

Design-Expert analysis

Estimation of Factor EffectsForm Tentative Model

Term Effect SumSqr % ContributionModel InterceptModel A 8.33333 208.333 64.4995Model B -5 75 23.2198Model AB 1.66667 8.33333 2.57998Error Lack Of Fit 0 0Error P Error 31.3333 9.70072

Lenth's ME 6.15809 Lenth's SME 7.95671

Statistical Testing - ANOVA

The F-test for the “model” source is testing the significance of the overall model; that is, is either A, B, or AB or some combination of these effects important?

Design-Expert output, full model

Design-Expert output, edited or reduced model

Residuals and Diagnostic Checking

The Response Surface

The 23 Factorial Design

Effects in The 23 Factorial Design

etc, etc, ...

Analysis done via computer

An Example of a 23 Factorial Design

A = gap, B = Flow, C = Power, y = Etch Rate

Table of – and + Signs for the 23 Factorial Design (pg. 218)

Properties of the Table

• Except for column I, every column has an equal number of + and – signs

• The sum of the product of signs in any two columns is zero• Multiplying any column by I leaves that column unchanged (identity

element)• The product of any two columns yields a column in the table:

• Orthogonal design• Orthogonality is an important property shared by all factorial designs

A B AB

AB BC AB C AC

Estimation of Factor Effects

ANOVA Summary – Full Model

Model Coefficients – Full Model

Refine Model – Remove Nonsignificant Factors

Model Coefficients – Reduced Model

Model Summary Statistics for Reduced Model

• R2 and adjusted R2

• R2 for prediction (based on PRESS)

5.106 100.9608

5.314 10

/ 20857.75 /121 1 0.9509

/ 5.314 10 /15

E EAdj

SS dfR

2Pred 5

37080.441 1 0.9302

5.314 10T

PRESSR

Model Summary Statistics

• Standard error of model coefficients (full model)

• Confidence interval on model coefficients

2 2252.56ˆ ˆ( ) ( ) 11.872 2 2(8)

MSse V

/ 2, / 2,ˆ ˆ ˆ ˆ( ) ( )

E Edf dft se t se

The Regression Model

Model Interpretation

Cube plots are often useful visual displays of experimental results

Cube Plot of Ranges

What do the large ranges

when gap and power are at the high level tell

The General 2k Factorial Design• Section 6-4, pg. 227, Table 6-9, pg. 228• There will be k main effects, and

two-factor interactions2

three-factor interactions3

1 factor interaction

6.5 Unreplicated 2k Factorial Designs

• These are 2k factorial designs with one observation at each corner of the “cube”

• An unreplicated 2k factorial design is also sometimes called a “single replicate” of the 2k

• These designs are very widely used• Risks…if there is only one observation at each

corner, is there a chance of unusual response observations spoiling the results?

• Modeling “noise”?

Spacing of Factor Levels in the Unreplicated 2k Factorial Designs

If the factors are spaced too closely, it increases the chances that the noise will overwhelm the signal in the data

More aggressive spacing is usually best

Unreplicated 2k Factorial Designs

• Lack of replication causes potential problems in statistical testing– Replication admits an estimate of “pure error” (a better

phrase is an internal estimate of error)– With no replication, fitting the full model results in zero

degrees of freedom for error• Potential solutions to this problem

– Pooling high-order interactions to estimate error– Normal probability plotting of effects (Daniels, 1959)– Other methods…see text

Example of an Unreplicated 2k Design

• A 24 factorial was used to investigate the effects of four factors on the filtration rate of a resin

• The factors are A = temperature, B = pressure, C = mole ratio, D= stirring rate

• Experiment was performed in a pilot plant

The Resin Plant Experiment

Estimates of the Effects

The Half-Normal Probability Plot of Effects

Design Projection: ANOVA Summary for the Model as a 23 in Factors A, C, and D

The Regression Model

Model Residuals are Satisfactory

Model Interpretation – Main Effects and Interactions

Model Interpretation – Response Surface Plots

With concentration at either the low or high level, high temperature and high stirring rate results in high filtration rates

Outliers: suppose that cd = 375 (instead of 75)

Dealing with Outliers

• Replace with an estimate• Make the highest-order interaction zero• In this case, estimate cd such that ABCD =

0• Analyze only the data you have• Now the design isn’t orthogonal• Consequences?

The Drilling Experiment Example 6.3

A = drill load, B = flow, C = speed, D = type of mud, y = advance rate of the drill

Normal Probability Plot of Effects –The Drilling Experiment

Residual Plots

DESIGN-EXPERT Plotadv._rate

Predicted

Residuals vs. Predicted

-1.96375

-0.82625

0.31125

1.44875

2.58625

1.69 4.70 7.70 10.71 13.71

• The residual plots indicate that there are problems with the equality of variance assumption

• The usual approach to this problem is to employ a transformation on the response

• Power family transformations are widely used

• Transformations are typically performed to – Stabilize variance– Induce at least approximate normality– Simplify the model

Residual Plots

Selecting a Transformation

• Empirical selection of lambda• Prior (theoretical) knowledge or experience can

often suggest the form of a transformation• Analytical selection of lambda…the Box-Cox

(1964) method (simultaneously estimates the model parameters and the transformation parameter lambda)

• Box-Cox method implemented in Design-Expert

(15.1)

The Box-Cox MethodDESIGN-EXPERT Plotadv._rate

LambdaCurrent = 1Best = -0.23Low C.I. = -0.79High C.I. = 0.32

Recommend transform:Log (Lambda = 0)

Lambda

Box-Cox Plot for Power Transforms

-3 -2 -1 0 1 2 3

A log transformation is recommended

The procedure provides a confidence interval on the transformation parameter lambda

If unity is included in the confidence interval, no transformation would be needed

Effect Estimates Following the Log Transformation

Three main effects are large

No indication of large interaction effects

What happened to the interactions?

ANOVA Following the Log Transformation

Following the Log Transformation

The Log Advance Rate Model

• Is the log model “better”?• We would generally prefer a simpler model

in a transformed scale to a more complicated model in the original metric

• What happened to the interactions?• Sometimes transformations provide insight

into the underlying mechanism

Other Examples of Unreplicated 2k Designs

• The sidewall panel experiment (Example 6.4, pg. 245)– Two factors affect the mean number of defects– A third factor affects variability– Residual plots were useful in identifying the dispersion

effect

• The oxidation furnace experiment (Example 6.5, pg. 245)– Replicates versus repeat (or duplicate) observations?– Modeling within-run variability

Other Analysis Methods for Unreplicated 2k Designs

• Lenth’s method (see text, pg. 235)– Analytical method for testing effects, uses an estimate

of error formed by pooling small contrasts– Some adjustment to the critical values in the original

method can be helpful– Probably most useful as a supplement to the normal

probability plot

• Conditional inference charts (pg. 236)

Optimal Designs

• These results give us some assurance that these designs are “good” designs in some general ways

• Factorial designs typically share some (most) of these properties

• There are excellent computer routines for finding optimal designs (JMP is outstanding)

Addition of Center Points to a 2k Designs

• Based on the idea of replicating some of the runs in a factorial design

• Runs at the center provide an estimate of error and allow the experimenter to distinguish between two possible models:

First-order model (interaction)

Second-order model

i i ij i ji i j i

k k k k

i i ij i j ii ii i j i i

y x x x

y x x x x

no "curvature"F Cy y

The hypotheses are:

Pure Quad

( )F C F C

n n y ySS

This sum of squares has a single degree of freedom

Example 6.6, Pg. 248

Usually between 3 and 6 center points will work well

Design-Expert provides the analysis, including the F-test for pure quadratic curvature

Refer to the original experiment shown in Table 6.10. Suppose that four center points are added to this experiment, and at the points x1=x2 =x3=x4=0 the four observed filtration rates were 73, 75, 66, and 69. The average of these four center points is 70.75, and the average of the 16 factorial runs is 70.06. Since are very similar, we suspect that there is no strong curvature present.

ANOVA for Example 6.6 (A Portion of Table 6.22)

If curvature is significant, augment the design with axial runs to create a central composite design. The CCD is a very effective design

for fitting a second-order response surface model

Practical Use of Center Points (pg. 260)

• Use current operating conditions as the center point

• Check for “abnormal” conditions during the time the experiment was conducted

• Check for time trends• Use center points as the first few runs when there

is little or no information available about the magnitude of error

• Center points and qualitative factors?

Chapter 6Based on Design & Analysis of Experiments 7E 2009 Montgomery 1 Design and Analysis of...

Documents

Analysis of QUENCH-ACM Experiments using SCDAP…€¦ · Analysis of QUENCH-ACM Experiments using ... investigates heat-up and ... interim post-test analysis of the QUENCH-ACM experiments,

DESIGN AND ANALYSIS OF EXPERIMENTS: NONPARAMETRIC METHODS ...€¦ · design and analysis of experiments: nonparametric methods with ... of experiments: nonparametric methods with

Statistical Analysis of Experimental Datariener.vwl.uni-mannheim.de/uploads/media/ExpEconEconometrics.pdf · Data Analysis and Experiments Data Analysis and Experiments IGood experimental

Excursions in Modern Mathematics, 7e: 15.5 - 2Copyright © 2010 Pearson Education, Inc. 15 Chances, Probabilities, and Odds 15.1Random Experiments and

Chapter 13Design & Analysis of Experiments 7E 2009 Montgomery 1 Design of Engineering Experiments - Experiments with Random Factors Text reference, Chapter

Excursions in Modern Mathematics, 7e: 15.6 - 2Copyright © 2010 Pearson Education, Inc. 15 Chances, Probabilities, and Odds 15.1Random Experiments and

Laboratory Experiments Qualitative Analysis

Excursions in Modern Mathematics, 7e: 15.2 - 2Copyright © 2010 Pearson Education, Inc. 15 Chances, Probabilities, and Odds 15.1Random Experiments and

Design of Engineering Experiments The 2k-p Fractional Factorial Designnoordin/s/aqe ch08 rev.pdf · Chapter 8 Design and Analysis of Experiments 7E 2009 Montgomery 1 Chapter 8 Design

Chapter 11 Design & Analysis of Experiments 1 7E 2009 …noordin/s/ch11 rev [Compatibility... · 2011. 3. 13. · Chapter 11 Design & Analysis of Experiments 7E 2009 Montgomery 2

Student Experiments for Quantitative Chemical Analysis · Quantitative Chemical Analysis Experiment List-1 Student Experiments for Quantitative Chemical Analysis This list of experiments,

HCCI Combustion: Analysis and Experiments

Exercises in the Design and Analysis of Experiments Henrik ... · PDF fileDesign and Analysis of Experiments Henrik Spliid ... Regular exercises in the design and analysis of experiments:

Quantitative Chemical Analysis 7e

Excursions in Modern Mathematics, 7e: 15.3 - 2Copyright © 2010 Pearson Education, Inc. 15 Chances, Probabilities, and Odds 15.1Random Experiments and

Excursions in Modern Mathematics, 7e: 15.4 - 2Copyright © 2010 Pearson Education, Inc. 15 Chances, Probabilities, and Odds 15.1Random Experiments and

Analysis of Optimization Experiments

Analysis of Reliability Experiments with Random …...Analysis of Reliability Experiments with Random Blocks and Subsampling Jennifer L. K. Kensler (ABSTRACT) Reliability experiments

Chapter 3 Design & Analysis of Experiments 1 7E 2009 Montgomerynoordin/s/aqe ch03 rev.pdf · Chapter 3 Design & Analysis of Experiments 7E 2009 Montgomery 2 An Example (See pg. 61)An

Project Management Systems Analysis and Design, 7e Kendall & Kendall 3