View
234
Download
0
Category
Preview:
Citation preview
8/14/2019 Chapter 4heat Student's Copy
1/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
4.1 : UNDERSTANDING THERMAL EQUILIBRIUM
By the end of this subtopic, you will be able to
Explain thermal equilibrium
Explain how a liquid-in glass thermometer works
1. The net heat will flow from A to B until the temperature of A is the ( same, zero as the
temperature of B. In this situation, the two bodies are said to have reached thermal
equilibrium.
2. When thermal equilibrium is reached, the net rate of heat flow between the two bodies is
(zero, equal)
3. There is no net flow of heat between two objects that are in thermal equilibrium. Two objects
in thermal equilibrium have the temperature.
4. The liquid used in glass thermometer should
(a) Be easily seen
(b) Expand and contract rapidly over a wide range of temperature
(c) Not stick to the glass wall of the capillary tube
5. List the characteristic of mercury
(a) Opaque liquid
(b) Does not stick to the glass
(c) Expands uniformly when heated
(d) Freezing point -390C
(e) Boiling point 3570C
1
Thermal equilibrium:Keseimbangan terma
CHAPTER 4: HEAT
..
.
..
..
.
.
.
.
.. rate of energy transfer
Hot
object
Cold
object
.. rate of energy transfer
Equivalent to Equivalent to
No net heat transfer
A B
8/14/2019 Chapter 4heat Student's Copy
2/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
6. ( Heat, Temperature ) is a form of energy. It flows from a hot body to a cold body.
7. The SI unit for( heat , temperature) is Joule, J.
8. ( Heat , Temperature ) is the degree of hotness of a body
9. The SI unit for (heat , temperature) is Kelvin, K.
10. Lower fixed point (l0 )/ ice point : the temperature of pure melting ice/00C
11. Upper fixed point( l 100)/steam point: the temperature of steam from water that is boiling
under standard atmospheric pressure /1000C
Exercise 4.1
Section A: Choose the best answer
1. The figure shows two metal blocks.
Which the following statement is false?
A. P and Q are in thermal contact
B. P and Q are in thermal equilibriumC. Energy is transferred from P to Q
D. Energy is transferred from Q to P
2. When does the energy go when a cup of
hot tea cools?
A. It warms the surroundings
B. It warms the water of the tea
C. It turns into heat energy anddisappears.
3. Which of the following temperature
corresponds to zero on the Kelvin scale?A. 2730 C
B. 00C
C. -2730 CD. 1000 C
4. How can the sensitivity of a liquid- in glass thermometer be increased?
A. Using a liquid which is a better
conductor of heat
2
..
l0
: length of mercury at ice point
l100
: length of mercury at steam point
Temperature, =l
- l0
l
x 1000C
8/14/2019 Chapter 4heat Student's Copy
3/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
B. Using a capillary tube with anarrower bore.
C. Using a longer capillary tubeD. Using a thinner-walked bulb
5. Which instrument is most suitable formeasuring a rapidly changing
temperature?
A. Alcohol-in glass thermometerB. Thermocouple
C. Mercury-in-glass thermometer
D. Platinum resistance thermometer
6. When shaking hands with Anwar, Kent
Hui niticed that Anwars hand was cold.However, Anwar felt that Kent Hui hand
was warm. Why did Anwar and Kent
Hui not feel the same sensation?A. Both hands in contact are in
thermal equilibrium.B. Heat is flowing from Kent Huis
hand to Anawrs hand
C. Heat is following from Anwars
hand to Kent Hui hand.
Section B: Answer all the questions by showing the calculation
1. The length of the mercury column at the ice point and steam point are 5.0 cm and 40.0cmrespectively. When the thermometer is immersed in the liquid P, the length of the mercury
column is 23.0 cm. What is the temperature of the liquid P?
2. The length of the mercury column at the steam point and ice point and are 65.0 cm
and 5.0cm respectively. When the thermometer is immersed in the liquid Q, the length of the
mercury column is 27.0 cm. What is the temperature of the liquid Q?
Temperature, = l l0 x 1000C
l100 l0
= 27 5 x 1000C
65 - 5
= 36.670C
3
8/14/2019 Chapter 4heat Student's Copy
4/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
3. The distance between 00C and 1000C is 28.0 cm. When the thermometer is put into a beaker
of water, the length of mercury column is 24.5cm above the lower fixed point. What is the
temperature of the water?
4. The distance between 00C and 1000C is 25 cm. When the thermometer is put into a beaker of
water, the length of mercury column is 16cm above the lower fixed point. What is the
temperature of the water? What is the length of mercury column from the bulb at
temperatures i) 300C
4
8/14/2019 Chapter 4heat Student's Copy
5/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
SECTION C: Structured Questions
1. Luqman uses an aluminium can, a drinking straw and some plasticine to make a simple
thermometer as shown in figure below. He pours a liquid with linear expansion into the can.
(a) Suggest a kind of liquid that expands linearly. (1m)
.
(b) He chooses two fixed points of Celsius scale to calibrate his thermometer. State them
(2m)
(c) If the measurement length of the liquid inside the straw at the temperature of the lower
fixed point and the upper fixed point are 5cm and 16 cm respectively, find the length of
the liquid at 82.50C.
(d) Why should he use a drinking straw of small diameter?
(e) What kind of action should he take if he wants to increase the sensitivity of his
thermometer?
5
8/14/2019 Chapter 4heat Student's Copy
6/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
2. What do you mean by heat and temperature?
....
4.2 : UNDERSTANDING SPECIFIC HEAT CAPACITY
By the end of this subtopic, you will be able to
Define specific heat capacity
State that c = Q/MC
Determine the specific heat capacity of a liquid
Determine the specific heat capacity of a solid
Describe applications of specific heat capacity
Solve problems involving specific heat capacity
1. The .. of a body is the .. that must be supplied to the body
to increase its temperature by 10C.
2. The heat capacity of an object depends on the
(a) .
(b) .
(c)
3. The of a substance is the amount of heat that must be supplied to
increase the temperature by 1 0C for a mass of 1 kg of the substance. UnitJkg-1K-1
4. The heat energy absorbed or given out by an object is given by Q = mcO.
6
Heat capacityMuatan haba
Specific heat capacityMuatan haba tentu
Specific heat capacity , c =Q__
8/14/2019 Chapter 4heat Student's Copy
7/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
5. High specific heat capacity absorb a large amount of heat with only a
temperature increase such as plastics.
6. Conversion of energy
7. Applications of Specific Heat Capacity
Explain the meaning of above application of specific heat capacity:
(a) Water as a coolant in a car engine
(i) ...................................................................................................................................
...................................................................................................................................
...................................................................................................................................
7
Electrical energy Heat energy
Pt = mc
Heater
Power = Penergy
..energy
..energy
Object falls from
A hi h osition
Moving object stopped
due to friction
Heat energy
m h= mc
Heat energy
mv2= mc
Small value of c Big value of cTwo object of
equal mass
Equal rate ofheat supplied
.
increase intem erature
.
increase intem erature
8/14/2019 Chapter 4heat Student's Copy
8/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
...................................................................................................................................
...................................................................................................................................
.....
(b) Household apparatus and utensils
...
...
...
...
(c) Sea breeze
(d) Land breeze
8
8/14/2019 Chapter 4heat Student's Copy
9/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
Exercise 4.2
SECTION A : Choose the best answer
1. The change in the temperature of an
object does not depend onA. the mass of the object
B. the type of substance the object ismade of
C. the shape of the object
D. the quantity of heat received
2. Which of the following defines thespecific heat capacity of a substance
correctly?
A. The amount of heat energy requiredto raise the temperature of 1kg of the
substance
B. The amount of heat energy requiredto raise 1kg of the substance by 10C.
C. The amount of heat energy required
to change 1kg of the substance from
the solid state to the liquid state.
3. Heat energy is supplied at the same rate
to 250g of water and 250g of ethanol.The temperature of the ethanol rises
faster. This is because the ethanol..A. is denser than water
B. is less dense than water
C. has a larger specific heat capacity
than waterD. has a smaller specific heat capacity
than water
4. In the experiment to determine the
specific heat capacity of a metal block,
some oil is poured into the holecontaining thermometer. Why is this
done?
A. To ensure a better conduction of heatB. To reduce the consumption of
electrical energy
C. To ensure the thermometer is in an
upright position.D. To reduce the friction between the
thermometer and the wall of the
block.
SECTION B: Answer all questions by showing the calculation
9
8/14/2019 Chapter 4heat Student's Copy
10/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
1. How much heat energy is required to raise the temperature of a 4kg iron bar from 320C to
520C? (Specific heat capacity of iron = 452 Jkg-1 0C-1).
2. Calculate the amount of heat required to raise the temperature of 0.8 kg of copper from 350C
to 600C. (Specific heat capacity of copper = 400 J kg -1 C-1).
3. Calculate the amount of heat required to raise the temperature of 2.5 kg of water from 320C
to 820C. (Specific heat capacity of water = 4200 J kg -1 C-1).
4. 750g block of a aluminium at 1200C is cooled until 450C. Find the amount of heat is
released. . (Specific heat capacity of aluminium = 900 J kg -1 C-1).
5. 0.2 kg of water at 700C is mixed with 0.6 kg of water at 300C. Assuming that no heat is lost,
find the final temperature of the mixture. (Specific heat capacity of water = 4200 J kg-1 C-1)
10
8/14/2019 Chapter 4heat Student's Copy
11/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
SECTION C: Structured questions
1. In figure below, block A of mass 5kg at temperature 1000C is in contact with another block B
of mass 2.25kg at temperature 200C.
Assume that there is no energy loss to the surroundings.
(a) Find the final temperature of A and B if they are in thermal equilibrium. Given the
specific heat capacity of A and B are 900 Jkg-1 C-1 and 400 Jkg-1 C-1 respectively.
(b) Find the energy given by A during the process.
(c) Suggest one method to reduce the energy loss to the surroundings.
..
11
AB
1000C 200C
5kg
2.25kg
8/14/2019 Chapter 4heat Student's Copy
12/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
4.3 UNDERSTANDING SPECIFIC LATENT HEAT
By the of this subtopic, you will be able to
State that transfer of heat during a change of phase does not cause a change in temperature
Define specific latent heat
State that l = Q/m
Determine the specific latent heat of fusion and specific latent heat of vaporisation
Solve problem involving specific latent heat.
1. Four main changes of phase.
2. The heat absorbed or the heat released at constant temperature during a change of
phase is known as latent heat. Q= ml
3. Complete the diagrams below and summarized.
(a) Melting
12
SolidSolidification
Latent heat
Boiling
Latent heat . Condensation
Latent heat
Li uid
Gas
8/14/2019 Chapter 4heat Student's Copy
13/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
(b) Boiling
(c) Solidification
(d) Condensation
13
Tem erature
Time
.
Tem erature
Time
.
Tem erature
Time
.
Tem erature
Time
.
8/14/2019 Chapter 4heat Student's Copy
14/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
4. is the heat absorbed by a melting solid. The specific latent
heat of fusion is the quantity of the heat needed to change 1kg of solid to a liquid at its
melting point without any increase in .. The S.I unit of the specific
latent heat of fusion is Jkg-1.
5. ... is heat of vaporisation is heat absorbed during boiling.
The specific latent heat of vaporisation is the quantity of heat needed to change 1kg ofliquid
into gas or vapour of its boiling point without any change in .. The S.I
unit is Jkg-1.
14
waterice
watergas
8/14/2019 Chapter 4heat Student's Copy
15/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
6. Explain the application of Specific Latent Heat above:
:
(d) Cooling of beverage
(e) Preservation of Food
15
8/14/2019 Chapter 4heat Student's Copy
16/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
(f) Steaming Food
(g) Killing of Germs and Bacteria
EXERCISE 4.3
Section A:
1. The graph in figure below shows how
the temperature of some wax changes asit cools from liquid to solid. Which
section of the graph would the wax be a
mixture of solid and liquid?
16
8/14/2019 Chapter 4heat Student's Copy
17/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
A. PQ
B. QR C. RS
D. ST
2. Figure show a joulemeter used formeasuring the electrical energy to melt
some ice in an experiment. To find the
specific latent heat of fusion of ice, what
must be measured?
A. The time taken for the ice to meltB. The voltage of the electricity supply
C. The mass of water produced by
melting iceD. The temperature change of the ice.
3. It is possible to cook food much faster
with a pressure cooker as shown above.
Why is it easier to cook food using apressure cooker?
A. More heat energy can be supplied to
the pressure cooker
B. Heat loss from the pressure cookercan be reduced.
C. Boiling point of water in the pressure
cooker is raisedD. Food absorbs more heat energy from
the high pressure steam
4. Which of the following is not a
characteristics of water that makes it
widely used as a cooling agent?
A. Water is readily availableB. Water does not react with many other
substanceC. Water has a large specific heat
capacity
D. Water has a large density
5. Figure below shows the experiment set
up to determine the specific latent heat
of fusion of ice. A control of theexperiment is set up as shown in Figure
(a) with the aim of
17
8/14/2019 Chapter 4heat Student's Copy
18/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
A. determining the rate of melting of ice
B. ensuring that the ice does not melttoo fast.
C. determining the average value of the
specific latent heat of fusion of ice.
D. determining the mass of ice thatmelts as a result of heat from the
surroundings
6. Scalding of the skin by boiling water is
less serious then by steam. This isbecause
A. the boiling point of water is less than
the temperature of steamB. the heat of boiling water is quickly
lost to the surroundings
C. steam has a high specific latent heat.
D. Steam has a high specific heatcapacity.
SECTION B: Answer the question by showing the calculation
1. 300g of ice at 00C melts. How much energy is required for this
Question 2-7 are based on the following information
Specific heat capacity of water = 4 200 J kg-1 C-1
Specific heat capacity of ice = 2 100 J kg-1 C-1
Specific latent heat of fusion of ice = 3.34 X 105J kg-1
Specific latent heat of vaporization of water = 2.26 X 106 J kg-1
2. An immersion heater rated at 500 W is fitted into a large block of ice at 00C. How long does
it take to melt 1.5kg of ice?
3. 300 g of water at 400C is mixed with x g of water at 800C. The final temperature of the
mixture is 700C. Find the value of x
18
8/14/2019 Chapter 4heat Student's Copy
19/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
4. Calculate the amount of heat released when 2 kg of ice at 00C is changed into water at 00C.
5. Calculate the amount of heat needed to convert 3 kg of ice at 00C to water at 300C.
6. Find the amount of heat needed to convert 0.5 kg of ice at 150C into steam at 1000C
7. Calculate the amount of heat needed to convert 100 g of ice at 00C into steam at 1000C.
8. The specific latent heat of vaporization of water is 2300 kJ kg-1. How much heat will be
absorbed when 3.2 kg of water is boiled off at its boiling point.
4.4 UNDERSTANDING THE GAS LAW
By the end of this subtopic; you will be able to :
Explain gas pressure, temperature and volume in terms of the behaviour of gas molecules.
Determine the relationship between
19
8/14/2019 Chapter 4heat Student's Copy
20/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
(i) pressure and volume
(ii) volume and temperature
(iii) pressure and temperature
Explain absolute zero and the absolute/Kelvin scale of temperature
Solve problems involving pressure, temperature and volume of a fixed mass of gas
1. Complete the table below.
Property of gas ExplanationVolume,V
m3
Temperature,T
K (Kelvin)
Pressure,P
Pa(Pascal)
2. The kinetic theory of gas is based on the following assumptions:
...............................................................................................................................................
...............................................................................................................................................
...............................................................................................................................................
...............................................................................................................................................
....
4.4.1 Boyles Law
20
Small volume
molecules hit wall
more often, greater
pressure
P 1
V
That is PV = constant
Or P V = P V
Relationshi between ressure and volume
8/14/2019 Chapter 4heat Student's Copy
21/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
1. Boyles law states that...
............................................................................
2. Boyles law can be shown graphically as in Figure above
3. The volume of an air bubble at the base of a sea of 50 m deep is 250cm3. If the atmospheric
pressure is 10m of water, find the volume of the air bubble when it reaches the surface of the
sea.
21
P
V
(a) P inversely proportional to V
P
1/V
(b) P directly proportional to 1/V
PI=50m + 10m
V1=250cm3
P2= 10m
8/14/2019 Chapter 4heat Student's Copy
22/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
4.4.2 Charless Law
1. Charles law states .
The temperature -2730C is the lowest possible temperature and is known as the absolutezero of
temperature.
2. Fill the table below.
Temperature Celsius scale (0C) Kelvin Scale(K)
Absolute zero
Ice point
Steam point
22
Relationship between
volume and temperature
Lower temperature
Higher temperature,
faster molecules,
larger volume to keep
the pressure constant
V T
that is V = constant
T
8/14/2019 Chapter 4heat Student's Copy
23/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
Unknown point
3. Complete the diagram below.
4.4.3 Pressures Law
1. The pressure law states ....
..
EXERSICE 4.4:Gas Law
1. A mixture of air and petrol vapour is injected into the cylinder of a car engine when the
cylinder volume is 100 cm3. Its pressure is then 1.0 atm. The valve closes and the mixture is
compressed to 20 cm3. Find the pressure now.
23
/0C100-273
P T
That is P = constant T
Relationship between pressure
and temperature
Higher temperature
molecules move
faster, greater
pressure
8/14/2019 Chapter 4heat Student's Copy
24/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
2. The volume of an air bubble at the base of a sea of 50 in deep is 200 cm3. If the atmospheric
pressure is 10 in of water, find the volume of the air bubble when it reaches the surface of
the sea.
3. The volume of an air bubble is 5 mm3 when it is at a depth of h in below the water surface.
Given that its volume is 15 mm3 when it is at a depth of 2 in, find the value of h.
(Atmospheric pressure = 10 m of water)
4. An air bubble has a volume of V cm3 when it is released at a depth of 45m from the water
surface. Find its volume (V) when it reaches the water surface. (Atmospheric pressure = 10
m of water)
24
8/14/2019 Chapter 4heat Student's Copy
25/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
5. A gas of volume 20m3 at 370C is heated until its temperature becomes 870C at constant
pressure. What is the increase in volume?
6. The air pressure in a container at 330C is 1.4 X 1O5 N m2. The container is heated until the
temperature is 550C. What is the final air pressure if the volume of the container is fixed?
7. The volume of a gas is 1 cm3 at 150C. The gas is heated at fixed pressure until the volume
becomes triple the initial volume. Calculate the final temperature of the gas.
8. An enclosed container contains a fixed mass of gas at 250C and at the atmospheric pressure.
The container is heated and temperature of the gas increases to 980C. Find the new pressure
of the gas if the volume of the container is constant.(Atmospheric pressure = 1.0 X 105N
rn2)
25
8/14/2019 Chapter 4heat Student's Copy
26/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
9. The pressure of a gas decreases from 1.2 x 105 Pa to 9 x 105 Pa at 400C. If the volume of the
gas is constant, find the initial temperature of the gas.
PART A: CHAPTER 4
1. A 5kg iron sphere of temperature 500C is
put in contact with a 1kg copper sphereof temperature 273K and they are put
inside an insulated box. Which of the
following statements is correct whenthey reach thermal equilibrium?
D. A iron sphere will have a
temperature of 273K
E. The copper sphere will have a
temperature of 500
C.F. Both the sphere have the same
temperature.
G. The temperature of the ironsphere will be lower than 500C
2. In the process to transfer heat from oneobject to another object, which of the
26
8/14/2019 Chapter 4heat Student's Copy
27/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
following processes does not involve a
transfer to material?
A. ConvectionB. Vaporisation
C. Radiation
D. Evaporation
3. When we use a microwave oven to heat
up some food in a lunch box, we shouldopen the lid slightly. Which of the
following explanations is correct?
A. To allow microwave to go inside
the lunch boxB. To allow the water vapors to go
out, otherwise the box will
explode
C. To allow microwave to reflectmore times inside the lunch box
D. To allow microwave to penetratedeeper into the lunch box.
4. Water is generally used to put out fire.
Which of the following explanation is
not correct?
A. Water has a high specific heat
capacityB. Steam can cut off the supply of
oxygen
C. Water is easily availableD. Water can react with some
material
5. Given that the heat capacity of a certainsample is 5000 J0C-1. Which of the
following is correct?
A. The mass of this sample is 1kg.B. The energy needed to increase
the temperature of 1 kg of this
sample is 5000 J.C. The energy needed to increase
the temperature of 0.5kg of this
sample is 2500J.
D. The temperature of this sample
will increase 10C when 5 000 J
energy is absorbed by thissample.
6. Which of the following statement iscorrect?
A. The total mass of the object is
kept constant when fusionoccurs.
B. The internal energy of the object
is increased when condensation
occursC. Energy is absorbed when
condensation occurs.
D. Energy is absorbed when
vaporization occurs.
7. Water molecules change their statesbetween the liquid and gaseous states
A. only when water vapour is
saturatedB. at all times because evaporation
and condensation occur any time
C. only when the vapour moleculesproduce a pressure as the same as
the atmospheric pressure
D. only when the water is boiling
8. Based on the kinetic theory of gas which
one of the following does not explain the
behaviour of gas molecules in acontainer?
A. Gas molecules move randomly
B. Gas molecules collide elasticallywith the walls of the container
C. Gas molecules move faster as
temperature increasesD. Gas molecules collide
inelastically with each other
27
8/14/2019 Chapter 4heat Student's Copy
28/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
9. A cylinder which contains gas is
compressed at constant temperature of
the gas increase becauseA. the average speed of gas
molecules increases
B. the number of gas moleculesincreases
C. the average distance between the
gas molecules increasesD. the rate of collision between the
gas molecules and the walls
increases
10. A plastic bag is filled with air. It is
immersed in the boiling water as shown
in diagram below.
Which of the following statements isfalse?
A. The volume of the plastic bag
increases.B. The pressure of air molecules
increases
C. The air molecules in the bag
move fasterD. The repulsive force of boiling
water slows down the movement
of air molecule
PART B;
1. A research student wishes to carry out an investigation on the temperature change of the
substance in the temperature range -500C to 500C. The instrument used to measure the
temperature is a liquid in glass thermometer.
28
8/14/2019 Chapter 4heat Student's Copy
29/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
Table 1
(a) (i) State the principle used in a liquid- in glass thermometer.(1m)
........................................................................................................................................
(ii) Briefly explain the principle stated in (a)(i) (3m)
.
.
.
(b) Table 1 shows the characteristic of 4 types of thermometer: A,B C and D. On the basis
of the information given in Table 1, explain the characteristics of, and suggest a suitable
thermometer for the experiment.(5 m)
Thermometer A B C D
Liquid Mercury Mercury Alcohol Alcohol
Freezing point of liquid (0C) -39 -39 -112 -112
Boiling point of liquid (0C) 360 360 360 360
Diameter of capillary tube Large Small Large Small
Cross section
29
8/14/2019 Chapter 4heat Student's Copy
30/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
..
(c) The length of the mercury column in uncalibrated thermometer is 6.0cm and 18.5 cm at
00C and 1000C. respectively. When the thermometer is placed in a liquid, the length of
the mercury column is 14.0cm
(i) Calculate the temperature of the liquid
(ii) State two thermometric properties which can be used to calibrate a thermometer. (6m)
2. A metal block P of mass 500 g is heated is boiling water at a temperature of 1000C. Block P
is then transferred into the water at a temperature of 300C in a polystyrene cup. The mass of
water in the polystyrene cup is 250 g. After 2 minutes, the water temperature rises to 420C.
Assuming that the heat absorbed by the polystyrene cup and heat loss to the
surroundings are negligible.{Specific heat capacity of water 4 200 j kg -1 C-1)
Calculate
(a) the quantity of heat gained by water the polystyrene cup
30
Figure 2
8/14/2019 Chapter 4heat Student's Copy
31/34
8/14/2019 Chapter 4heat Student's Copy
32/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
(c) Calculate the time taken by the lead shot to fall from the top to the bottom of the tube.
(d) After inverting the tube 100 times, the temperature of the lead shot is found to have
increased by 30C.
i. Calculate the work done on the lead shot.
ii. Calculate the specific heat capacity of lead.
iii. State the assumption used in your calculation in (d)ii.
...
.
PART C: EXPERIMENT
1. Before travelling on a long journey, Luqman measured the air pressure the tyre of his car as
shown in Figure (a) He found that the air pressure of the tyre was 200 kPa. After the journey,
Luqman measured again the air pressure of the tyre as shown in Figure (b) He found that the
air pressure had increase to 245 kPa. Luqman also found that the tyre was hotter after the
journey although the size of the tyre did not change.
Using the information provided by Luqman and his observations on air pressure in the
tyre of his car:
32
Figure (a) Figure (b)
8/14/2019 Chapter 4heat Student's Copy
33/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
Choose suitable apparatus
such as pressure gauge, a
round-bottomed flask and
any other apparatus that may he necessary. In your description, state clearly the
following:
i. Aim of the experiment,
ii. Variables in the experiment,
iii. List of apparatus and materials,
iv. Arrangement of the apparatus,
v. The procedure of the experiment including the method of controlling the
manipulated variable and the method of measuring the responding variable,
vi. The way you would tabulate the data,
vii. The way you would analyse the data. [10 marks]
33
(a) State one suitable inference that can be
made. [1 mark]
(b) State appropriate hypothesis for an
investigation. [1 mark]
(c) Design an experiment to investigate the
hypothesis stated in (b).
8/14/2019 Chapter 4heat Student's Copy
34/34
JPN Pahang Physics Module Form 4Students Copy Chapter 4: Heat
Recommended