View
250
Download
4
Category
Tags:
Preview:
DESCRIPTION
ccnn
Citation preview
CCNA Advance
Chapter 2Hot Standby Routing Protocol
Configuring Layer 3 Redundancy with HSRP
3
Routing Issues: Using Default Gateways
4
Routing Issues: Using Proxy ARP
5
Identifying the Router Redundancy Process
6
Identifying the Router Redundancy Process
7
Describing HSRP
8
The Active Router
The active router responds to ARP requests with the well-known MAC address ofthe virtual router.
9
The Virtual Router MAC Address
10
The Standby Router
The standby router listens for periodic hello messages on 224.0.0.2
11
Active and Standby Router Interaction
12
Describing HSRP States
An HSRP router can be in one of six different states: Initial Learn Listen Speak Standby Active
13
HSRP State Transition
14
HSRP Standby State
A router in the standby state: Is a candidate for active router Sends hello messages Knows the virtual router IP address
15
HSRP Active State
A router in the active state: Assumes the active forwarding of packets for the virtual router Sends hello messages Knows the virtual router IP address
16
HSRP Configuration Commands
17
Configuring an HSRP Standby Interface
Enabling HSRP on a Cisco router interface automaticallydisables ICMP redirects.
Optimizing HSRP
19
HSRP Optimization Options
These options can be configured to optimize HSRP: HSRP standby priority HSRP standby preempt Hello message timers HSRP interface tracking
20
Configuring HSRP Standby Priority
The router with the highest priority in an HSRP groupbecomes the active router. The default priority is 100. In the case of a tie, the router with the highestconfigured IP address will become active.
21
Configuring HSRP Standby Preempt
Preempt enables a router to resume the forwarding router role.
22
Configuring the Hello Message Timer
The holdtime parameter value should be at least threetimes the value of the hellotime parameter.
23
HSRP Interface Tracking
24
HSRP Interface Tracking (Cont.)
25
Configuring HSRP Tracking
Configures HSRP tracking
Example of HSRP tracking
26
Tuning HSRP
- Configure hellotime and holdtime to millisecond values.- Configure preempt delay timer so that preempt occurs only after the distribution switch has fully rebooted and established full connectivityto the rest of the network.
27
Multiple HSRP Groups
To load balance routers, assign them to multiple groups on the same subnet.
28
Addressing HSRP GroupsAcross Trunk Links
To loadbalance routersand links: Per VLAN,configurethe HSRPactiverouter andthespanningtree root tobe thesamemultilayerswitch.
29
About the HSRP Debug Command
30
Debugging HSRP
31
Debugging HSRP (Cont.)
32
Summary
Router redundancy allows two or more routers to work as a group to maintain forwarding of IP packets. A single default gateway or proxy ARP does not provide the redundancy required in a campus network. HSRP provides router redundancy to end devices. HSRP operates to provide nonstop path redundancy for IP. An HSRP-enabled router will exist in a specific state or transition through a series ofstates. HSRP is configured using the standby command. HSRP is enabled per interface. Preempt, timers, and interface tracking are options that can beconfigured to optimizeHSRP.
33
Summary
HSRP preempt can be tuned by adjusting timers that can thereby reduce failover time. To facilitate load sharing, a single interface on a router can be a member of multiple HSRP groups. Specific debug commands are used to view HSRP state changes. Debug can be used to discover the virtual IP address and the priority of the active and standby routers.
Question ?
Thank you !
CCNA AdvanceConfiguring Layer 3 Redundancy with HSRPRouting Issues: Using Default GatewaysRouting Issues: Using Proxy ARPIdentifying the Router Redundancy ProcessIdentifying the Router Redundancy ProcessDescribing HSRPThe Active RouterThe Virtual Router MAC AddressThe Standby RouterActive and Standby Router InteractionDescribing HSRP StatesHSRP State TransitionHSRP Standby StateHSRP Active StateHSRP Configuration CommandsConfiguring an HSRP Standby InterfaceOptimizing HSRPHSRP Optimization OptionsConfiguring HSRP Standby PriorityConfiguring HSRP Standby PreemptConfiguring the Hello Message TimerHSRP Interface TrackingHSRP Interface Tracking (Cont.)Configuring HSRP TrackingTuning HSRPMultiple HSRP GroupsAddressing HSRP GroupsAcross Trunk LinksAbout the HSRP Debug CommandDebugging HSRPDebugging HSRP (Cont.)SummarySummaryQuestion ?Recommended