View
2
Download
0
Category
Preview:
Citation preview
APPLICATIONS PCD CBN
HARD CAST IRON NO YES
SOFT CAST IRON NO YES
HARDENED STEEL NO YES
SUPER ALLOYS NO YES
ABRASIVE NONMETALLIC YES NO
NONFERROUS MATERIALS YES NO
BASIC APPLICATION GUIDELINES
Cubic Boron Nitride (CBN) CBN tipped tools and inserts are excellent for the
continuous cutting of a wide range of hardened steels, powdered metals, cast irons and super alloys. The
products are precision ground with hones for machining to sub-micron finishes with maximum tool life. CBN tipped
tools can take the place of grinding.
Polycrystalline Diamond (PCD) PCD tipped boring bars and inserts are excellent
for continuous cutting of a wide range of non-ferrous and non-metal materials. The products are precision ground for machining to sub-micron finishes with maximum tool
life. PCD tipped tools allow for higher cutting speedswith longer tool life.
Guidelines for PCDHigher speeds minimze tool buildup.Depth of cut should not exceed 70% of PCD tip length.Use of coolant will reduce heat and improve surface finish.Do not stop the machine with the tool in cut - this will result in tool breakage.Make sure the machine and setup is rigid and solid; chatter will cause chipping.Tool height when boring should be slightly above center; tool deflection will put the tool on center.Do not contact the tool to a hard surface prior to the machining process - this will cause chipping.
(Ideal for non-ferrous materials)
Guidelines for CBNDepth of cut should not exceed 30% of CBN tip length.Coolant use is not advised as it could cause thermal crackingDo not stop the machine with the tool in cut - this will result in tool breakage.Make sure the machine and setup is rigid and solid; chatter will cause chipping.Tool height when boring should be slightly above center; tool deflection will put the tool on center.Do not contact the tool to a hard surface prior to the machining process - this will cause chipping.
(Ideal for hard ferrous metal -45 Rc plus)
CBN and PCD tipped solid carbide boring bar minimum bore options starting at 0.120"
CBN and PCD tipped indexable boring bar minimum bore options starting at 0.220"
All CBN and PCD tipped boring bars have premium submicron carbide bodies and a precision ground flat
CBN and PCD tipped indexable inserts are sold separately
CBN and PCD indexable inserts are available for triangle or diamond shaped left or right-hand bars
Scientific Cutting Tools, Inc. (800) 383-2244(805) 584-9495
Fax: (888) 728-3295www.sct-usa.comFax: (805) 584-9629
sales@sct-usa.com2
Min bore 0.220 ...................p.4Min bore 0.286 ...................p.4Min bore 0.300 ...................p.6Min bore 0.350 ...................p.4Min bore 0.363 ...................p.6Min bore 0.421 ...................p.5Min bore 0.430 ...................p.7Min bore 0.545 ...................p.5Min bore 0.560 ...................p.7
Min bore 0.120 ...................p.8Min bore 0.140 ...................p.8Min bore 0.160 ...................p.8Min bore 0.180 ...................p.8Min bore 0.200 ...................p.8Min bore 0.230 ...................p.8Min bore 0.290 ...................p.9Min bore 0.320 ...................p.9Min bore 0.360 ...................p.9
View the technical information for CBN products on page 10.
PCD tipped tools and inserts are located on pages 12-17.
CBN Tipped Tools & Inserts
INDEXABLE BAR WITH INSERT CBN Tipped Inserts
SINGLE POINT CARBIDE BODYCBN Tipped Boring Bars
CBN Tipped Tools and Inserts
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH3/16” BAR ORDER #
NO COOLANT HOLE
5° 0.220 0.112 NONE ACD5 RIGHT ACBC187R5R
5° 0.220 0.112 FLAT ACD5 RIGHT ACBC187F5R
0° 0.220 0.112 NONE ACD5 RIGHT ACBC187R0R
0° 0.220 0.112 FLAT ACD5 RIGHT ACBC187F0R
5° 0.220 0.112 NONE ACD5 LEFT ACBC187R5L
5° 0.220 0.112 FLAT ACD5 LEFT ACBC187F5L
0° 0.220 0.112 NONE ACD5 LEFT ACBC187R0L
0° 0.220 0.112 FLAT ACD5 LEFT ACBC187F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH1/4” BAR ORDER #
NO COOLANT HOLE
5° 0.286 0.146 NONE ACD5 RIGHT ACBC250R5R
5° 0.286 0.146 FLAT ACD5 RIGHT ACBC250F5R
0° 0.286 0.146 NONE ACD5 RIGHT ACBC250R0R
0° 0.286 0.146 FLAT ACD5 RIGHT ACBC250F0R
5° 0.286 0.146 NONE ACD5 LEFT ACBC250R5L
5° 0.286 0.146 FLAT ACD5 LEFT ACBC250F5L
0° 0.286 0.146 NONE ACD5 LEFT ACBC250R0L
0° 0.286 0.146 FLAT ACD5 LEFT ACBC250F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH5/16” BAR ORDER #
NO COOLANT HOLE
5° 0.350 0.179 NONE ACD5 RIGHT ACBC312R5R
5° 0.350 0.179 FLAT ACD5 RIGHT ACBC312F5R
0° 0.350 0.179 NONE ACD5 RIGHT ACBC312R0R
0° 0.350 0.179 FLAT ACD5 RIGHT ACBC312F0R
5° 0.350 0.179 NONE ACD5 LEFT ACBC312R5L
5° 0.350 0.179 FLAT ACD5 LEFT ACBC312F5L
0° 0.350 0.179 NONE ACD5 LEFT ACBC312R0L
0° 0.350 0.179 FLAT ACD5 LEFT ACBC312F0L
“L” ANGLE
“A”MIN
BORE“F”
FLATON
STEP
INSERTTYPE
RH/LHSTEP BAR ORDER #
NO COOLANT HOLE
0° 0.220 0.112 YES ACD5 RIGHT ACBC187S4F0R
ONESCREW
“R” CORNER RADIUS
ORDER #
ONE CBNINSERT
AT6+ 0.007 ACD5071CBN2
AT6+ 0.015 ACD5151CBN2
80° DIAMOND CBN TIPPED
.156
R .040
15°
INDEXABLE BORING BARS AND CBN INSERTS3/16”, 1/4”, AND 5/16” CBN DIAMOND SHAPED INSERTS
EACH BAR COMES WITH ONE SCREW AND ONE KEY. INSERTS SOLD SEPARATELY.
3/16” Bar (0.1875 Shank Dia.) 3.0 OAL 1/4” Bar (0.250 Shank Dia.) 4.0 OAL
5/16” Bar (0.3125 Shank Dia.) 4.0 OAL
1/2” Step Bar (0.500 Shank Diameter)
All 3/16", 1/4", and 5/16" bars use AT6+ screws (for triangle or diamond-shaped inserts)
AT6+ screws are the same right or left handed bars
For use in adjustable boring heads Eliminates the need for a bushing or sleeve in most lathes
Coolant use is not advised as it could cause thermal cracking CBN is excellent for continuous cutting of a wide range of
hardened steels, cast irons, powdered metals, and super alloys CBN tipped inserts can take the place of grinding Honed for machining to sub-micron finishes with max tool life
S A
OAL
L
F
Carbide ShankSteel Head
One Tipped Cutting Edge
.500
2.8 1.310
.220 .112
R
0º Carbide SteelSteel
One Tipped Cutting Edge
ACCESSORY REPLACEMENT PACKSITEM SIZE ORDER #
FLAG KEY (2 PACK ) AT6+ A6KEY
SCREWS (10 PACK) AT6+ A6SCREWS
4 CBN Tipped Indexable Inserts
INDEXABLE BORING BARS AND CBN INSERTS3/8” AND 1/2” CBN DIAMOND SHAPED INSERTS
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH3/8” BAR ORDER #
NO COOLANT HOLE
5° 0.421 0.218 NONE ACP2 RIGHT ACBC375R5R
5° 0.421 0.218 FLAT ACP2 RIGHT ACBC375F5R
0° 0.421 0.218 NONE ACP2 RIGHT ACBC375R0R
0° 0.421 0.218 FLAT ACP2 RIGHT ACBC375F0R
5° 0.421 0.218 NONE ACP2 LEFT ACBC375R5L
5° 0.421 0.218 FLAT ACP2 LEFT ACBC375F5L
0° 0.421 0.218 NONE ACP2 LEFT ACBC375R0L
0° 0.421 0.218 FLAT ACP2 LEFT ACBC375F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH1/2” BAR ORDER #
NO COOLANT HOLE
5° 0.545 0.280 NONE ACP2 RIGHT ACBC500R5R
5° 0.545 0.280 FLAT ACP2 RIGHT ACBC500F5R
0° 0.545 0.280 NONE ACP2 RIGHT ACBC500R0R
0° 0.545 0.280 FLAT ACP2 RIGHT ACBC500F0R
5° 0.545 0.280 NONE ACP2 LEFT ACBC500R5L
5° 0.545 0.280 FLAT ACP2 LEFT ACBC500F5L
0° 0.545 0.280 NONE ACP2 LEFT ACBC500R0L
0° 0.545 0.280 FLAT ACP2 LEFT ACBC500F0L
EACH BAR COMES WITH ONE SCREW AND ONE KEY. INSERTS SOLD SEPARATELY.
3/8” Bar (0.375 Shank Dia.) 5.5 OAL
1/2” Bar (0.500 Shank Dia.) 6.6 OAL
ONESCREW
“R” CORNER RADIUS
ORDER #
ONE CBNINSERT
AT6+ 0.007 ACP2071CBN2
AT6+ 0.015 ACP2151CBN2
80° DIAMOND CBN TIPPED
All 3/8 and 1/2" bars use AT8+ screws (for triangle or diamond-shaped inserts)
AT8+ screws are the same right or left handed bars
ACCESSORY REPLACEMENT PACKSITEM SIZE ORDER #
FLAG KEY (2 PACK ) AT8+ A8KEY
SCREWS (10 PACK) AT8+ A8SCREWS
Coolant use is not advised as it could cause thermal cracking CBN is excellent for continuous cutting of a wide range of
hardened steels, cast irons, powdered metals, and super alloys CBN tipped inserts can take the place of grinding Honed for machining to sub-micron finishes with max tool life
S A
OAL
L
F
Carbide ShankSteel Head
One Tipped Cutting Edge
5CBN Tipped Indexable Inserts
.250
R .075
11°
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH1/4” BAR ORDER #
NO COOLANT HOLE
5° 0.300 0.160 NONE ATD5 RIGHT ACBT250R5R
5° 0.300 0.160 FLAT ATD5 RIGHT ACBT250F5R
0° 0.300 0.160 NONE ATD5 RIGHT ACBT250R0R
0° 0.300 0.160 FLAT ATD5 RIGHT ACBT250F0R
5° 0.300 0.160 NONE ATD5 LEFT ACBT250R5L
5° 0.300 0.160 FLAT ATD5 LEFT ACBT250F5L
0° 0.300 0.160 NONE ATD5 LEFT ACBT250R0L
0° 0.300 0.160 FLAT ATD5 LEFT ACBT250F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH5/16” BAR ORDER #
NO COOLANT HOLE
5° 0.363 0.192 NONE ATD5 RIGHT ACBT312R5R
5° 0.363 0.192 FLAT ATD5 RIGHT ACBT312F5R
0° 0.363 0.192 NONE ATD5 RIGHT ACBT312R0R
0° 0.363 0.192 FLAT ATD5 RIGHT ACBT312F0R
5° 0.363 0.192 NONE ATD5 LEFT ACBT312R5L
5° 0.363 0.192 FLAT ATD5 LEFT ACBT312F5L
0° 0.363 0.192 NONE ATD5 LEFT ACBT312R0L
0° 0.363 0.192 FLAT ATD5 LEFT ACBT312F0L
“L” ANGLE
“A”MIN
BORE“F”
FLATON
STEP
INSERTTYPE
RH/LHSTEP BAR ORDER #
NO COOLANT HOLE
0° 0.300 0.160 YES ATD5 RIGHT ACBC250S4F0R
“L” ANGLE
“A”MIN
BORE“F”
FLATON
STEP
INSERTTYPE
RH/LHSTEP BAR ORDER #
NO COOLANT HOLE
0° 0.363 0.192 YES ATD5 RIGHT ACBT312S4F0R
ONESCREW
“R” CORNER RADIUS
ORDER #
ONE CBNINSERT
AT6+ 0.007 ATD5071CBN2
AT6+ 0.015 ATD5151CBN2
60° TRIANGLE CBN TIPPED
INDEXABLE BORING BARS AND CBN INSERTS1/4” AND 5/16” CBN TRIANGLE SHAPED INSERTS
EACH BAR COMES WITH ONE SCREW AND ONE KEY. INSERTS SOLD SEPARATELY.
1/4” Bar (0.250 Shank Dia.) 4.0 OAL 5/16” Bar (0.3125 Shank Dia.) 4.0 OAL
1/2” Step Bar (0.500 Shank Diameter) 1/2” Step Bar (0.500 Shank Diameter)
ACCESSORY REPLACEMENT PACKSITEM SIZE ORDER #
FLAG KEY (2 PACK ) AT6+ A6KEY
SCREWS (10 PACK) AT6+ A6SCREWS
All 3/16", 1/4", and 5/16" bars use AT6+ screws (for triangle or diamond-shaped inserts)
AT6+ screws are the same right or left handed bars
.160
R .047
15°
Coolant use is not advised as it could cause thermal cracking CBN is excellent for continuous cutting of a wide range of
hardened steels, cast irons, powdered metals, and super alloys CBN tipped inserts can take the place of grinding Honed for machining to sub-micron finishes with max tool life
A
OAL
S F
L Carbide ShankSteel Head
One Tipped Cutting Edge
For use in adjustable boring heads Eliminates the need for a bushing or sleeve in most lathes
3.2
.500.300
1.750
.160
R
0º CarbideSteel Steel
One Tipped Cutting Edge
3.6
.500.363
2.190
.192
R
0º CarbideSteel Steel
One Tipped Cutting Edge
6 CBN Tipped Indexable Inserts
INDEXABLE BORING BARS AND CBN INSERTS3/8” AND 1/2” CBN TRIANGLE SHAPED INSERTS
EACH BAR COMES WITH ONE SCREW AND ONE KEY. INSERTS SOLD SEPARATELY.
3/8” Bar (0.375 Shank Dia.) 5.5 OAL
1/2” Bar (0.500 Shank Dia.) 6.6 OAL
ONESCREW
“R” CORNER RADIUS
ORDER #
ONE CBNINSERT
AT6+ 0.007 ATP2071CBN2
AT6+ 0.015 ATP2151CBN2
60° TRIANGLE CBN TIPPED
All 3/8 and 1/2" bars use AT8+ screws (for triangle or diamond-shaped inserts)
AT8+ screws are the same right or left handed bars
.250
R .096
11°
Coolant use is not advised as it could cause thermal cracking CBN is excellent for continuous cutting of a wide range of
hardened steels, cast irons, powdered metals, and super alloys CBN tipped inserts can take the place of grinding Honed for machining to sub-micron finishes with max tool life
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH3/8” BAR ORDER #
NO COOLANT HOLE
5° 0.430 0.229 NONE ATP2 RIGHT ACBT375R5R
5° 0.430 0.229 FLAT ATP2 RIGHT ACBT375F5R
0° 0.430 0.229 NONE ATP2 RIGHT ACBT375R0R
0° 0.430 0.229 FLAT ATP2 RIGHT ACBT375F0R
5° 0.430 0.229 NONE ATP2 LEFT ACBT375R5L
5° 0.430 0.229 FLAT ATP2 LEFT ACBT375F5L
0° 0.430 0.229 NONE ATP2 LEFT ACBT375R0L
0° 0.430 0.229 FLAT ATP2 LEFT ACBT375F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH1/2” BAR ORDER #
NO COOLANT HOLE
5° 0.560 0.295 NONE ATP2 RIGHT ACBT500R5R
5° 0.560 0.295 FLAT ATP2 RIGHT ACBT500F5R
0° 0.560 0.295 NONE ATP2 RIGHT ACBT500R0R
0° 0.560 0.295 FLAT ATP2 RIGHT ACBT500F0R
5° 0.560 0.295 NONE ATP2 LEFT ACBT500R5L
5° 0.560 0.295 FLAT ATP2 LEFT ACBT500F5L
0° 0.560 0.295 NONE ATP2 LEFT ACBT500R0L
0° 0.560 0.295 FLAT ATP2 LEFT ACBT500F0L
A
OAL
S F
L Carbide ShankSteel Head
One Tipped Cutting Edge
ACCESSORY REPLACEMENT PACKSITEM SIZE ORDER #
FLAG KEY (2 PACK ) AT8+ A8KEY
SCREWS (10 PACK) AT8+ A8SCREWS
7CBN Tipped Indexable Inserts
BORING BARS - CBN TIPPED
Application: For hard cast iron applications such as pumps, impellers, and shafts. For soft cast iron applications such as enginge blocks, brake rotors, and transer housings. For hardened steel applications such as pinion
gears, shafts, and bearings. For super alloy applications such as turbine disk/blade and enginge shafts.
CBN for hard ferrous metal - 45Rc plus
Excellent for continuous cutting of a wide range of materials (see below)
Maintains tighter tolerances
Solid carbide body for maximum rigidity
“A”MIN
BORE
“B”MAX
DEPTH
“S”SHANK
DIA.OAL
ORDER #
CBN
0.120 0.250 0.1875 2.00 CBN-B120250
0.120 0.350 0.1875 2.00 CBN-B120350
0.120 0.500 0.1875 2.00 CBN-B120500
0.120 0.600 0.1875 2.00 CBN-B120600
0.120 0.700 0.1875 2.00 CBN-B120700
0.120 0.800 0.1875 2.00 CBN-B120800
0.140 0.250 0.1875 2.00 CBN-B140250
0.140 0.400 0.1875 2.00 CBN-B140400
0.140 0.500 0.1875 2.00 CBN-B140500
0.140 0.600 0.1875 2.00 CBN-B140600
0.140 0.700 0.1875 2.00 CBN-B140700
0.140 0.750 0.1875 2.00 CBN-B140750
0.140 0.800 0.1875 2.00 CBN-B140800
0.160 0.250 0.1875 2.00 CBN-B160250
0.160 0.400 0.1875 2.00 CBN-B160400
0.160 0.500 0.1875 2.00 CBN-B160500
0.160 0.600 0.1875 2.00 CBN-B160600
0.160 0.750 0.1875 2.00 CBN-B160750
0.160 0.900 0.1875 2.00 CBN-B160900
0.160 1.000 0.1875 2.00 CBN-B1601000
0.180 0.350 0.250 2.50 CBN-B180350
0.180 0.500 0.250 2.50 CBN-B180500
0.180 0.600 0.250 2.50 CBN-B180600
0.180 0.750 0.250 2.50 CBN-B180750
0.180 0.900 0.250 2.50 CBN-B180900
0.180 1.000 0.250 2.50 CBN-B1801000
0.180 1.100 0.250 2.50 CBN-B1801100
B
S A
2°
6° OAL
R.004
“A”MIN
BORE
“B”MAX
DEPTH
“S”SHANK
DIA.OAL
ORDER #
CBN
0.200 0.400 0.250 2.50 CBN-B200400
0.200 0.500 0.250 2.50 CBN-B200500
0.200 0.600 0.250 2.50 CBN-B200600
0.200 0.700 0.250 2.50 CBN-B200700
0.200 0.800 0.250 2.50 CBN-B200800
0.200 0.900 0.250 2.50 CBN-B200900
0.200 1.000 0.250 2.50 CBN-B2001000
0.200 1.100 0.250 2.50 CBN-B2001100
0.200 1.200 0.250 2.50 CBN-B2001200
0.200 1.300 0.250 2.50 CBN-B2001300
0.230 0.400 0.3125 2.50 CBN-B230400
0.230 0.500 0.3125 2.50 CBN-B230500
0.230 0.600 0.3125 2.50 CBN-B230600
0.230 0.700 0.3125 2.50 CBN-B230700
0.230 0.800 0.3125 2.50 CBN-B230800
0.230 0.900 0.3125 2.50 CBN-B230900
0.230 1.000 0.3125 2.50 CBN-B2301000
0.230 1.150 0.3125 2.50 CBN-B2301150
0.230 1.200 0.3125 2.50 CBN-B2301200
0.230 1.250 0.3125 2.50 CBN-B2301250
0.230 1.400 0.3125 2.50 CBN-B2301400
0.230 1.500 0.3125 2.50 CBN-B2301500
0.230 1.600 0.3125 2.50 CBN-B2301600
8 CBN Tipped Boring Bars
Application: For hard cast iron applications such as pumps, impellers, and shafts. For soft cast iron applications such as enginge blocks, brake rotors, and transer housings. For hardened steel applications such as pinion
gears, shafts, and bearings. For super alloy applications such as turbine disk/blade and enginge shafts.
“A”MIN
BORE
“B”MAX
DEPTH
“S”SHANK
DIA.OAL
ORDER #
CBN
0.290 0.500 0.3125 2.50 CBN-B2905000.290 0.600 0.3125 2.50 CBN-B2906000.290 0.750 0.3125 2.50 CBN-B2907500.290 0.900 0.3125 2.50 CBN-B2909000.290 1.000 0.3125 2.50 CBN-B29010000.290 1.100 0.3125 2.50 CBN-B29011000.290 1.250 0.3125 2.50 CBN-B29012500.290 1.350 0.3125 2.50 CBN-B29013500.290 1.500 0.3125 2.50 CBN-B29015000.290 1.600 0.3125 2.50 CBN-B29016000.290 1.750 0.3125 2.50 CBN-B29017500.320 0.500 0.375 2.50 CBN-B3205000.320 0.600 0.375 2.50 CBN-B3206000.320 0.750 0.375 2.50 CBN-B3207500.320 0.900 0.375 2.50 CBN-B3209000.320 1.000 0.375 2.50 CBN-B32010000.320 1.100 0.375 2.50 CBN-B32011000.320 1.250 0.375 2.50 CBN-B32012500.320 1.500 0.375 2.50 CBN-B32015000.320 1.600 0.375 2.50 CBN-B32016000.320 1.800 0.375 2.50 CBN-B32018000.320 2.000 0.375 4.00 CBN-B32020000.320 2.500 0.375 4.00 CBN-B32025000.320 3.000 0.375 4.00 CBN-B32030000.360 0.500 0.375 2.50 CBN-B3605000.360 0.600 0.375 2.50 CBN-B3606000.360 0.750 0.375 2.50 CBN-B3607500.360 0.900 0.375 2.50 CBN-B3609000.360 1.000 0.375 2.50 CBN-B36010000.360 1.150 0.375 2.50 CBN-B36011500.360 1.250 0.375 2.50 CBN-B36012500.360 1.500 0.375 2.50 CBN-B36015000.360 1.600 0.375 2.50 CBN-B36016000.360 1.800 0.375 2.50 CBN-B36018000.360 2.000 0.375 4.00 CBN-B36020000.360 2.500 0.375 4.00 CBN-B36025000.360 3.000 0.375 4.00 CBN-B3603000
BORING BARS - CBN TIPPED
Faster speeds and feeds
Coolant use not advised as it may cause
thermal cracking
Depth of cut should not exceed 30% of tip length
Can take the place of grindingB
S A
2°
6° OAL
R.004
9CBN Tipped Boring Bars
APPLICATIONS
HARD CASTIRON
Pumps
Impellers
Shafts
SOFT CASTIRON
Engine Blocks
Brake Rotors
Transfer Housings
HARDENED STEEL
Pinion Gears
Shafts
Bearings
SUPER ALLOYS
Turbine Disk
Turbine Blade
Engine Shafts
APPLICATION GUIDELINES
Make sure the machine and setup is rigid and solid.Chatter will cause chipping
Tool height when boring should be slightly above center. Tool deflection will put the tool on center.
Do not stop the machine with the tool in cut.This will result in tool breakage.
Coolant use is not advised as it could cause thermal cracking.
Do not contact the tool to a hard surface prior to themachining process. This will cause chipping.
Depth of cut should not exceed 30% of CBN tip length.
MATERIAL BHN/RcSPEED RANGE (SFM)
FEEDIPR
INDEXABLE BORING CBN TIPPED
INSERTS
SINGLE POINT CBN TIPPED BARS
TOOL DIAMETER
MAX DOCACD & ATD
MAX DOC ACP & ATP
.120-160 .180-.230 .290-.320 .360+MAX DOC MAX DOC MAX DOC MAX DOC
HEAT TREATED ALLOY 45-60Rc 200-600 .001-.005 0.01 0.04 0.003 0.004 0.006 0.009
TOOL STEEL 45-60Rc 200-600 .001-.005 0.01 0.04 0.003 0.004 0.006 0.009
NODULAR IRON N/A 600-1500 .001-.005 0.009 0.035 0.006 0.01 0.02 0.03
PEARLITIC IRON220-
240BHN600-2500 .001-.007 0.009 0.035 0.006 0.01 0.02 0.03
WHITE/CHILLED IRON 54-60Rc 200-500 .001-.005 0.008 0.035 0.005 0.008 0.012 0.015
SUPER ALLOY Ni BASE240-475
BHN200-800 001-.005 0.008 0.035 0.003 0.004 0.006 0.025
COBOLT BASED ALLOY, STELLITE
45-55Rc 200-500 .001-.005 0.008 0.035 0.003 0.004 0.006 0.009
INCONELS 45-55Rc 200-500 .001-.005 0.008 0.035 0.003 0.004 0.006 0.009
CBN APPLICATIONS
CBN TIPPED TOOLS SPEEDS AND FEEDS
SFM = Surface Feet per Minute DOC = Depth of Cut
AS THE DOC DECREASES THE FEED RATE CAN INCREASE
SCT CBN tools and inserts are excellent for continuous cutting of a wide range of hardened steels, powdered metals, cast irons and super alloys. The products are precision ground with hones for machining to sub-micron finishes with maximum tool life. CBN tipped tools and inserts can take the place of grinding.
10
PCD Tipped Tools & Inserts
Min bore 0.220 ...................p.12Min bore 0.286 ...................p.12Min bore 0.300 ...................p.14Min bore 0.350 ...................p.12Min bore 0.363 ...................p.14Min bore 0.421 ...................p.13Min bore 0.430 ...................p.15Min bore 0.545 ...................p.13Min bore 0.560 ...................p.15
Min bore 0.120 ...................p.16Min bore 0.140 ...................p.16Min bore 0.160 ...................p.16Min bore 0.180 ...................p.16Min bore 0.200 ...................p.16Min bore 0.230 ...................p.16Min bore 0.290 ...................p.17Min bore 0.320 ...................p.17Min bore 0.360 ...................p.17
PCD Tipped Tools and Inserts
View the technical information for PCD products on page 18.
INDEXABLE BAR WITH INSERT PCD Tipped Inserts
SINGLE POINT CARBIDE BODYPCD Tipped Boring Bars
CBN tipped tools and inserts are located on pages 4-9.
“L” ANGLE
“A”MIN
BORE“F”
FLATON
STEP
INSERTTYPE
RH/LHSTEP BAR ORDER #
NO COOLANT HOLE
0° 0.220 0.112 YES ACD5 RIGHT ACBC187S4F0R
ONESCREW
“R” CORNER RADIUS
ORDER #
ONE PCDINSERT
AT6+ 0.007 ACD5071PCD
AT6+ 0.015 ACD5151PCD
80° DIAMOND PCD TIPPED
.156
R .040
15°
INDEXABLE BORING BARS AND PCD INSERTS3/16”, 1/4”, AND 5/16” PCD DIAMOND SHAPED INSERTS
EACH BAR COMES WITH ONE SCREW AND ONE KEY. INSERTS SOLD SEPARATELY.
3/16” Bar (0.1875 Shank Dia.) 3.0 OAL 1/4” Bar (0.250 Shank Dia.) 4.0 OAL
5/16” Bar (0.3125 Shank Dia.) 4.0 OAL
1/2” Step Bar (0.500 Shank Diameter)
All 3/16", 1/4", and 5/16" bars use AT6+ screws (for triangle or diamond-shaped inserts)
AT6+ screws are the same right or left handed bars
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH3/16” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.220 0.112 NONE ACD5 RIGHT ACBC187R5R ADBC187R5R
5° 0.220 0.112 FLAT ACD5 RIGHT ACBC187F5R ADBC187F5R
0° 0.220 0.112 NONE ACD5 RIGHT ACBC187R0R ADBC187R0R
0° 0.220 0.112 FLAT ACD5 RIGHT ACBC187F0R ADBC187F0R
5° 0.220 0.112 NONE ACD5 LEFT ACBC187R5L ADBC187R5L
5° 0.220 0.112 FLAT ACD5 LEFT ACBC187F5L ADBC187F5L
0° 0.220 0.112 NONE ACD5 LEFT ACBC187R0L ADBC187R0L
0° 0.220 0.112 FLAT ACD5 LEFT ACBC187F0L ADBC187F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH1/4” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.286 0.146 NONE ACD5 RIGHT ACBC250R5R ADBC250R5R
5° 0.286 0.146 FLAT ACD5 RIGHT ACBC250F5R ADBC250F5R
0° 0.286 0.146 NONE ACD5 RIGHT ACBC250R0R ADBC250R0R
0° 0.286 0.146 FLAT ACD5 RIGHT ACBC250F0R ADBC250F0R
5° 0.286 0.146 NONE ACD5 LEFT ACBC250R5L ADBC250R5L
5° 0.286 0.146 FLAT ACD5 LEFT ACBC250F5L ADBC250F5L
0° 0.286 0.146 NONE ACD5 LEFT ACBC250R0L ADBC250R0L
0° 0.286 0.146 FLAT ACD5 LEFT ACBC250F0L ADBC250F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH5/16” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.350 0.179 NONE ACD5 RIGHT ACBC312R5R ADBC312R5R
5° 0.350 0.179 FLAT ACD5 RIGHT ACBC312F5R ADBC312F5R
0° 0.350 0.179 NONE ACD5 RIGHT ACBC312R0R ADBC312R0R
0° 0.350 0.179 FLAT ACD5 RIGHT ACBC312F0R ADBC312F0R
5° 0.350 0.179 NONE ACD5 LEFT ACBC312R5L ADBC312R5L
5° 0.350 0.179 FLAT ACD5 LEFT ACBC312F5L ADBC312F5L
0° 0.350 0.179 NONE ACD5 LEFT ACBC312R0L ADBC312R0L
0° 0.350 0.179 FLAT ACD5 LEFT ACBC312F0L ADBC312F0L
PCD is excellent for continuous cutting of a wide range of abrasive non-metallics and non-ferrous materials
Inserts are precision ground for machining to sub-micron finishes with maximum tool life
PCD tipped inserts allow for higher cutting speeds with longer tool life.
S A
OAL
L
F
Carbide ShankSteel Head
One Tipped Cutting Edge
.500
2.8 1.310
.220 .112
R
0º Carbide SteelSteel
One Tipped Cutting Edge
For use in adjustable boring heads Eliminates the need for a bushing or sleeve in most lathes
ACCESSORY REPLACEMENT PACKSITEM SIZE ORDER #
FLAG KEY (2 PACK ) AT6+ A6KEY
SCREWS (10 PACK) AT6+ A6SCREWS
12 PCD Tipped Indexable Inserts
INDEXABLE BORING BARS AND PCD INSERTS3/8” AND 1/2” PCD DIAMOND SHAPED INSERTS
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH3/8” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.421 0.218 NONE ACP2 RIGHT ACBC375R5R ADBC375R5R
5° 0.421 0.218 FLAT ACP2 RIGHT ACBC375F5R ADBC375F5R
0° 0.421 0.218 NONE ACP2 RIGHT ACBC375R0R ADBC375R0R
0° 0.421 0.218 FLAT ACP2 RIGHT ACBC375F0R ADBC375F0R
5° 0.421 0.218 NONE ACP2 LEFT ACBC375R5L ADBC375R5L
5° 0.421 0.218 FLAT ACP2 LEFT ACBC375F5L ADBC375F5L
0° 0.421 0.218 NONE ACP2 LEFT ACBC375R0L ADBC375R0L
0° 0.421 0.218 FLAT ACP2 LEFT ACBC375F0L ADBC375F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH1/2” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.545 0.280 NONE ACP2 RIGHT ACBC500R5R ADBC500R5R
5° 0.545 0.280 FLAT ACP2 RIGHT ACBC500F5R ADBC500F5R
0° 0.545 0.280 NONE ACP2 RIGHT ACBC500R0R ADBC500R0R
0° 0.545 0.280 FLAT ACP2 RIGHT ACBC500F0R ADBC500F0R
5° 0.545 0.280 NONE ACP2 LEFT ACBC500R5L ADBC500R5L
5° 0.545 0.280 FLAT ACP2 LEFT ACBC500F5L ADBC500F5L
0° 0.545 0.280 NONE ACP2 LEFT ACBC500R0L ADBC500R0L
0° 0.545 0.280 FLAT ACP2 LEFT ACBC500F0L ADBC500F0L
EACH BAR COMES WITH ONE SCREW AND ONE KEY. INSERTS SOLD SEPARATELY.
3/8” Bar (0.375 Shank Dia.) 5.5 OAL
1/2” Bar (0.500 Shank Dia.) 6.6 OAL
ONESCREW
“R” CORNER RADIUS
ORDER #
ONE PCDINSERT
AT6+ 0.007 ACP2071PCD
AT6+ 0.015 ACP2151PCD
80° DIAMOND PCD TIPPED
All 3/8 and 1/2" bars use AT8+ screws (for triangle or diamond-shaped inserts)
AT8+ screws are the same right or left handed bars
PCD is excellent for continuous cutting of a wide range of abrasive non-metallics and non-ferrous materials
Inserts are precision ground for machining to sub-micron finishes with maximum tool life
PCD tipped inserts allow for higher cutting speeds with longer tool life.
S A
OAL
L
F
Carbide ShankSteel Head
One Tipped Cutting Edge
ACCESSORY REPLACEMENT PACKSITEM SIZE ORDER #
FLAG KEY (2 PACK ) AT8+ A8KEY
SCREWS (10 PACK) AT8+ A8SCREWS
13PCD Tipped Indexable Inserts
.250
R .075
11°
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH1/4” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.300 0.160 NONE ATD5 RIGHT ACBT250R5R ADBT250R5R
5° 0.300 0.160 FLAT ATD5 RIGHT ACBT250F5R ADBT250F5R
0° 0.300 0.160 NONE ATD5 RIGHT ACBT250R0R ADBT250R0R
0° 0.300 0.160 FLAT ATD5 RIGHT ACBT250F0R ADBT250F0R
5° 0.300 0.160 NONE ATD5 LEFT ACBT250R5L ADBT250R5L
5° 0.300 0.160 FLAT ATD5 LEFT ACBT250F5L ADBT250F5L
0° 0.300 0.160 NONE ATD5 LEFT ACBT250R0L ADBT250R0L
0° 0.300 0.160 FLAT ATD5 LEFT ACBT250F0L ADBT250F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH5/16” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.363 0.192 NONE ATD5 RIGHT ACBT312R5R ADBT312R5R
5° 0.363 0.192 FLAT ATD5 RIGHT ACBT312F5R ADBT312F5R
0° 0.363 0.192 NONE ATD5 RIGHT ACBT312R0R ADBT312R0R
0° 0.363 0.192 FLAT ATD5 RIGHT ACBT312F0R ADBT312F0R
5° 0.363 0.192 NONE ATD5 LEFT ACBT312R5L ADBT312R5L
5° 0.363 0.192 FLAT ATD5 LEFT ACBT312F5L ADBT312F5L
0° 0.363 0.192 NONE ATD5 LEFT ACBT312R0L ADBT312R0L
0° 0.363 0.192 FLAT ATD5 LEFT ACBT312F0L ADBT312F0L
ONESCREW
“R” CORNER RADIUS
ORDER #
ONE PCDINSERT
AT6+ 0.007 ATD5071PCD
AT6+ 0.015 ATD5151PCD
60° TRIANGLE PCD TIPPED
INDEXABLE BORING BARS AND PCD INSERTS1/4” AND 5/16” PCD TRIANGLE SHAPED INSERTS
EACH BAR COMES WITH ONE SCREW AND ONE KEY. INSERTS SOLD SEPARATELY.
1/4” Bar (0.250 Shank Dia.) 4.0 OAL 5/16” Bar (0.3125 Shank Dia.) 4.0 OAL
All 3/16", 1/4", and 5/16" bars use AT6+ screws (for triangle or diamond-shaped inserts)
AT6+ screws are the same right or left handed bars
PCD is excellent for continuous cutting of a wide range of abrasive non-metallics and non-ferrous materials
Inserts are precision ground for machining to sub-micron finishes with maximum tool life
PCD tipped inserts allow for higher cutting speeds with longer tool life.
A
OAL
S F
L Carbide ShankSteel Head
One Tipped Cutting Edge
“L” ANGLE
“A”MIN
BORE“F”
FLATON
STEP
INSERTTYPE
RH/LHSTEP BAR ORDER #
NO COOLANT HOLE
0° 0.300 0.160 YES ATD5 RIGHT ACBC250S4F0R
“L” ANGLE
“A”MIN
BORE“F”
FLATON
STEP
INSERTTYPE
RH/LHSTEP BAR ORDER #
NO COOLANT HOLE
0° 0.363 0.192 YES ATD5 RIGHT ACBT312S4F0R
1/2” Step Bar (0.500 Shank Diameter) 1/2” Step Bar (0.500 Shank Diameter)
For use in adjustable boring heads Eliminates the need for a bushing or sleeve in most lathes
3.2
.500.300
1.750
.160
R
0º CarbideSteel Steel
One Tipped Cutting Edge
3.6
.500.363
2.190
.192
R
0º CarbideSteel Steel
One Tipped Cutting Edge
ACCESSORY REPLACEMENT PACKSITEM SIZE ORDER #
FLAG KEY (2 PACK ) AT6+ A6KEY
SCREWS (10 PACK) AT6+ A6SCREWS
14 PCD Tipped Indexable Inserts
.160
R .047
15°
INDEXABLE BORING BARS AND PCD INSERTS3/8” AND 1/2” PCD TRIANGLE SHAPED INSERTS
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH3/8” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.430 0.229 NONE ATP2 RIGHT ACBT375R5R ADBT375R5R
5° 0.430 0.229 FLAT ATP2 RIGHT ACBT375F5R ADBT375F5R
0° 0.430 0.229 NONE ATP2 RIGHT ACBT375R0R ADBT375R0R
0° 0.430 0.229 FLAT ATP2 RIGHT ACBT375F0R ADBT375F0R
5° 0.430 0.229 NONE ATP2 LEFT ACBT375R5L ADBT375R5L
5° 0.430 0.229 FLAT ATP2 LEFT ACBT375F5L ADBT375F5L
0° 0.430 0.229 NONE ATP2 LEFT ACBT375R0L ADBT375R0L
0° 0.430 0.229 FLAT ATP2 LEFT ACBT375F0L ADBT375F0L
“L” ANGLE
“A”MIN
BORE“F”
BAR FLAT
INSERTTYPE
RH/LH1/2” BAR ORDER #
NO COOLANT HOLE
COOLANT THROUGH
5° 0.560 0.295 NONE ATP2 RIGHT ACBT500R5R ADBT500R5R
5° 0.560 0.295 FLAT ATP2 RIGHT ACBT500F5R ADBT500F5R
0° 0.560 0.295 NONE ATP2 RIGHT ACBT500R0R ADBT500R0R
0° 0.560 0.295 FLAT ATP2 RIGHT ACBT500F0R ADBT500F0R
5° 0.560 0.295 NONE ATP2 LEFT ACBT500R5L ADBT500R5L
5° 0.560 0.295 FLAT ATP2 LEFT ACBT500F5L ADBT500F5L
0° 0.560 0.295 NONE ATP2 LEFT ACBT500R0L ADBT500R0L
0° 0.560 0.295 FLAT ATP2 LEFT ACBT500F0L ADBT500F0L
EACH BAR COMES WITH ONE SCREW AND ONE KEY. INSERTS SOLD SEPARATELY.
3/8” Bar (0.375 Shank Dia.) 5.5 OAL
1/2” Bar (0.500 Shank Dia.) 6.6 OAL
ONESCREW
“R” CORNER RADIUS
ORDER #
ONE PCDINSERT
AT6+ 0.007 ATP2071PCD
AT6+ 0.015 ATP2151PCD
60° TRIANGLE PCD TIPPED
All 3/8 and 1/2" bars use AT8+ screws (for triangle or diamond-shaped inserts)
AT8+ screws are the same right or left handed bars
.250
R .096
11°
PCD is excellent for continuous cutting of a wide range of abrasive non-metallics and non-ferrous materials
Inserts are precision ground for machining to sub-micron finishes with maximum tool life
PCD tipped inserts allow for higher cutting speeds with longer tool life.
A
OAL
S F
L Carbide ShankSteel Head
One Tipped Cutting Edge
ACCESSORY REPLACEMENT PACKSITEM SIZE ORDER #
FLAG KEY (2 PACK ) AT8+ A8KEY
SCREWS (10 PACK) AT8+ A8SCREWS
15PCD Tipped Indexable Inserts
BORING BARS - PCD TIPPED
Solid carbide body for maximum rigidity
Depth of cut should not exceed 70% of PCD tip length
Excellent for continuous cutting of a wide range of non-ferrous and non-metal materials
B
S A
2°
6° OAL
R.004
“A”MIN
BORE
“B”MAX
DEPTH
“S”SHANK
DIA.OAL
ORDER #
PCD
0.120 0.250 0.1875 2.00 PCD-B120250
0.120 0.350 0.1875 2.00 PCD-B120350
0.120 0.500 0.1875 2.00 PCD-B120500
0.120 0.600 0.1875 2.00 PCD-B120600
0.120 0.700 0.1875 2.00 PCD-B120700
0.120 0.800 0.1875 2.00 PCD-B120800
0.140 0.250 0.1875 2.00 PCD-B140250
0.140 0.400 0.1875 2.00 PCD-B140400
0.140 0.500 0.1875 2.00 PCD-B140500
0.140 0.600 0.1875 2.00 PCD-B140600
0.140 0.700 0.1875 2.00 PCD-B140700
0.140 0.750 0.1875 2.00 PCD-B140750
0.140 0.800 0.1875 2.00 PCD-B140800
0.160 0.250 0.1875 2.00 PCD-B160250
0.160 0.400 0.1875 2.00 PCD-B160400
0.160 0.500 0.1875 2.00 PCD-B160500
0.160 0.600 0.1875 2.00 PCD-B160600
0.160 0.750 0.1875 2.00 PCD-B160750
0.160 0.900 0.1875 2.00 PCD-B160900
0.160 1.000 0.1875 2.00 PCD-B1601000
0.180 0.350 0.250 2.50 PCD-B180350
0.180 0.500 0.250 2.50 PCD-B180500
0.180 0.600 0.250 2.50 PCD-B180600
0.180 0.750 0.250 2.50 PCD-B180750
0.180 0.900 0.250 2.50 PCD-B180900
0.180 1.000 0.250 2.50 PCD-B1801000
0.180 1.100 0.250 2.50 PCD-B1801100
“A”MIN
BORE
“B”MAX
DEPTH
“S”SHANK
DIA.OAL
ORDER #
PCD
0.200 0.400 0.250 2.50 PCD-B200400
0.200 0.500 0.250 2.50 PCD-B200500
0.200 0.600 0.250 2.50 PCD-B200600
0.200 0.700 0.250 2.50 PCD-B200700
0.200 0.800 0.250 2.50 PCD-B200800
0.200 0.900 0.250 2.50 PCD-B200900
0.200 1.000 0.250 2.50 PCD-B2001000
0.200 1.100 0.250 2.50 PCD-B2001100
0.200 1.200 0.250 2.50 PCD-B2001200
0.200 1.300 0.250 2.50 PCD-B2001300
0.230 0.400 0.3125 2.50 PCD-B230400
0.230 0.500 0.3125 2.50 PCD-B230500
0.230 0.600 0.3125 2.50 PCD-B230600
0.230 0.700 0.3125 2.50 PCD-B230700
0.230 0.800 0.3125 2.50 PCD-B230800
0.230 0.900 0.3125 2.50 PCD-B230900
0.230 1.000 0.3125 2.50 PCD-B2301000
0.230 1.150 0.3125 2.50 PCD-B2301150
0.230 1.200 0.3125 2.50 PCD-B2301200
0.230 1.250 0.3125 2.50 PCD-B2301250
0.230 1.400 0.3125 2.50 PCD-B2301400
0.230 1.500 0.3125 2.50 PCD-B2301500
0.230 1.600 0.3125 2.50 PCD-B2301600
16 PCD Tipped Boring Bars
Application: For abrasive non-metallic applications such as carbon fiber bicycles and car parts, ceramic gas turbine parts, and bearings, and fiberglass bodies for cars/boats. For non-ferrous material applications such as
aluminum rims and spools, brass fittings, precious metals, and presintered tungsten carbide.
“A”MIN
BORE
“B”MAX
DEPTH
“S”SHANK
DIA.OAL
ORDER #
PCD
0.290 0.500 0.3125 2.50 PCD-B2905000.290 0.600 0.3125 2.50 PCD-B2906000.290 0.750 0.3125 2.50 PCD-B2907500.290 0.900 0.3125 2.50 PCD-B2909000.290 1.000 0.3125 2.50 PCD-B29010000.290 1.100 0.3125 2.50 PCD-B29011000.290 1.250 0.3125 2.50 PCD-B29012500.290 1.350 0.3125 2.50 PCD-B29013500.290 1.500 0.3125 2.50 PCD-B29015000.290 1.600 0.3125 2.50 PCD-B29016000.290 1.750 0.3125 2.50 PCD-B29017500.320 0.500 0.375 2.50 PCD-B3205000.320 0.600 0.375 2.50 PCD-B3206000.320 0.750 0.375 2.50 PCD-B3207500.320 0.900 0.375 2.50 PCD-B3209000.320 1.000 0.375 2.50 PCD-B32010000.320 1.100 0.375 2.50 PCD-B32011000.320 1.250 0.375 2.50 PCD-B32012500.320 1.500 0.375 2.50 PCD-B32015000.320 1.600 0.375 2.50 PCD-B32016000.320 1.800 0.375 2.50 PCD-B32018000.320 2.000 0.375 4.00 PCD-B32020000.320 2.500 0.375 4.00 PCD-B32025000.320 3.000 0.375 4.00 PCD-B32030000.360 0.500 0.375 2.50 PCD-B3605000.360 0.600 0.375 2.50 PCD-B3606000.360 0.750 0.375 2.50 PCD-B3607500.360 0.900 0.375 2.50 PCD-B3609000.360 1.000 0.375 2.50 PCD-B36010000.360 1.150 0.375 2.50 PCD-B36011500.360 1.250 0.375 2.50 PCD-B36012500.360 1.500 0.375 2.50 PCD-B36015000.360 1.600 0.375 2.50 PCD-B36016000.360 1.800 0.375 2.50 PCD-B36018000.360 2.000 0.375 4.00 PCD-B36020000.360 2.500 0.375 4.00 PCD-B36025000.360 3.000 0.375 4.00 PCD-B3603000
BORING BARS - PCD TIPPED
Use of coolant will reduce heat and improve surface finish
Allow for higher cutting speeds with longer tool life
Maintains tighter tolerancesB
S A
2°
6° OAL
R.004
17PCD Tipped Boring Bars
Application: For abrasive non-metallic applications such as carbon fiber bicycles and car parts, ceramic gas turbine parts, and bearings, and fiberglass bodies for cars/boats. For non-ferrous material applications such as
aluminum rims and spools, brass fittings, precious metals, and presintered tungsten carbide.
MATERIAL BHN/RcSPEED RANGE (SFM)
FEEDIPR
INDEXABLE BORING PCD TIPPED
INSERTS
SINGLE POINT PCD TIPPED BARS
TOOL DIAMETER
MAX DOCACD & ATD
MAX DOC ACP & ATP
.120-160 .180-.230 .290-.320 .360+MAX DOC MAX DOC MAX DOC MAX DOC
LOW SILICONALUMINUM
225-350 BHN
1000-5000 .001-.007 0.025 0.08 0.015 0.021 0.03 0.045
HIGH SILICONALUMINUM
270-425 BHN
600-3000 .001-.007 0.025 0.08 0.015 0.021 0.03 0.045
METAL MATRIXCOMPOSITIES
N/A 500-2000 .001-.007 0.015 0.035 0.008 0.012 0.02 0.03
COPPER ALLOYS, BRASS, BRONZE
80-120 BHN
750-3500 .001-.007 0.025 0.08 0.015 0.021 0.03 0.045
PRESINTERED TUNGSTEN CARBIDE
140-300 BHN
100-350 .001-.005 0.007 0.012 0.003 0.005 0.007 0.012
ACRYLICS N/A 700-1500 .001-.007 0.025 0.08 0.015 0.021 0.03 0.045
FIBERGLASS N/A 600-1000 .001-.007 0.02 0.06 0.012 0.02 0.03 0.045
GRAPHITES N/A 600-1000 .001-.007 0.025 0.08 0.015 0.021 0.03 0.045
NYLON, PLASTIC N/A 700-1500 .001-.007 0.025 0.08 0.015 0.021 0.03 0.045
HARD RUBBER N/A 500-2500 .001-.007 0.025 0.08 0.015 0.021 0.03 0.045
SFM = Surface Feet per Minute DOC= Depth of Cut
APPLICATIONS
ABRASIVENONMETALLIC
Carbon Fiber Bicycles
Carbon Fiber Car Parts
Ceramic Gas Turbine Parts
Ceramic Bearings
Fiberglass Bodiesfor Cars and Boats
NONFERROUSMATERIALS
Aluminum Rims
Aluminum Spools
Brass Fittings
Precious Metals
Presintered Tungsten Carbide
APPLICATION GUIDELINES
Make sure the machine and setup is rigid and solid.Chatter will cause chipping.
Tool height when boring should be slightly above center.Tool deflection will put the tool on center.
Do not stop the machine with the tool in cut.This will result in tool breakage.
Use of coolant will reduce heat and improve surface finish.
Do not contact the tool to a hard surface prior to themachining process- this will cause chipping.
Higher speeds minimize tool buildup.
Depth of cut should not exceed 70% of PCD tip length.
PCD APPLICATIONS
PCD TIPPED TOOLS SPEEDS AND FEEDS
AS THE DOC DECREASES THE FEED RATE CAN INCREASE SCT PCD tools and inserts are excellent for continuous cutting of a wide range of non-ferrous and non-metal materials. The products are precision ground for machining to sub-micron finishes with maximum tool life. PCD allows for higher cutting speeds with longer tool life.
18
19
A Legacy of ExcellenceScientific Cutting Tools, Inc. was established as an innovative cutting tool manufacturer based upon the simple marketing concept of providing customers with superior products, competitive prices, and uncompromising customer service. SCT entered the cutting tool manufacturing field with one drivinggoal—to deliver unprecedented value to our customers.
Over the years, SCT has developed new tool lines and refined existing product groups. Through aggressive research and development, SCT has the capability of developing specialized tools for specific customer projects, as well as the ability to modify existing stock tools to meet individual customer needs.
Although 53 years have passed since SCT first opened its doors, our fundamental reasons for being in business have remained the same as those originally established by company founder Stan Christopher. Our commitment to quality control, unparalleled craftsmanship, and customer satisfaction continue to set us above the competition.
Adopting a company philosophy of “pride in our people means pride in workmanship,” has proven to be the spark to ignite our ability to provide the best value in the industry. SCT’s team of specially trained machinists, operators, engineers, and our customer service team all take pride in dedication to their craft and producing the highest quality goods for our customers.
SCT has an excellent reputation as a manufacturer of an extensive line of cutting tools including thread mills, port tools, cavity tools, indexable and solid carbide boring bars, threading tools, coolant through tools, and more. We stock coated (AlTiN) and uncoated versions of our products and all carbide used in our processes must pass stringent quality tests.
SCT’s commitment to only working with the latest CNC tool and cutter grinders, and turning centers as well as dedicated employees using forward-thinking technology has allowed us to produce top-end cutting tools using quality materials at competitive market prices.
New Addition: The CRT HolderOur CRT holders are made from high quality heat-treated steel, come with a black oxide coating and are engineered to allow for better coolant penetration deep into the bore, reducing temperature at the cutting edge. The adjustable back stop is infinitely adjustable rather than fixed. This allows all of our single point tools to be set at their ideal maximum bore length, allowing for superior performance without chatter or other performance related issues. The CRT holder delivers a 360° flow of coolant to all of SCT’s single point tools. Use with our qualified boring bars and/or qualified threading tools for quick change machining.
Scientific Cutting Tools, Inc. (800) 383-2244(805) 584-9495
Fax: (888) 728-3295www.sct-usa.comFax: (805) 584-9629
sales@sct-usa.com
Distributed By:Manufactured By:
MORE TOOLS AND OPTIONSUse this chart to find out more about our tool collection and locate each tool in our print or online catalog.
To view our catalog online go to: www.sct-usa.com or request a catalog: www.sct-usa.com/catalog-request
External - UNJ
SPTM - UN TMLR - UN Straight Flute - UN
30º Helical Flute - UN
SPTM - METRIC
15º Helical Flute - METRIC
Staggered Tooth - UN
NPT / NPTF
TMLR - METRIC
30º Helical Flute - METRIC
15º Helical Flute - UN
BSPP / BSPT
Straight Flute - METRIC
SPTM - ACME / STUB ACME
THREAD MILLS SINGLE POINT TOOLS
Single Point Holders Radial Relief Boring BarsMini Boring Bars
Boring Bars Left-Hand Boring Bars Radius Boring Bars
Profile Boring Bars
Thread Tools Qualified
Groove Tools Full Radius
PCD/CBN TippedBoring Bars
Back Chamfer Boring Bars
Thread Tools
O-Ring Groove Tools
Helical Boring Bars
Acme Threading Tools
Groove Tool Retaining Ring
Face Groove Tools Undercut Groove Tools
INDEXABLE CARBIDE BORING BARS
SPECIALTY END MILLS
Corner Rounding End Mills Engraving Tools
Scientific Cutting Tools110 W. Easy Street
Simi Valley, CA 93065www.sct-usa.com
Tapered Pipe Reamer BSPP – Pipe Reamer
MS16142-S
MS16142-R
ISO6149-1 ISO6149-1 (ID)
MS33649-S MS33649-R
AND10050-S
AND10050-R
HydraforceBACD2036 Sun Hydraulic
Hard To Find Port Tools
Parker Common Cavity
MS33651
PORT & CAVITY TOOLS
MS33514 MS21921RPT – Rosan Cavity
Triangle Insert Indexable Bars
SOLID OR COOLANT THROUGH
Diamond Insert Indexable Bars
SOLID OR COOLANT THROUGH
Triangle Insert Step BarsDiamond Insert Step Bars
Flat Top Inserts Chip Control Inserts PCD/CBN Inserts
Several of our tools now have coolant through options. Please call or view our catalog to find out more.
SCT TOOL SPOTLIGHT: CRT HOLDER
Our newest addition to the tool holder line uses Coolant Ring Technology. It surrounds the tool
in 360° of coolant. Read more on page 19.
Recommended