View
2
Download
0
Category
Preview:
Citation preview
Assembly Manual
712570303
Building Dimensions
140.2524.756’ x 5’ 69.75” 62” 72” 66” 54” 71”
Storage AreaApproximate Size Interior DimensionsExterior Dimensions
Roof Edge to Roof Edge
1.8 m x 1.5 m 2.30 m2 3.97 m3 177.17 cm 157.48 cm 182.88 cm 167.64 cm 137.16 cm 180.34 cm
6x5
Wall to Wall
DepthSq. Ft. Width HeightWidth Depth Height Cu. Ft.
CAUTIONSharp Edges
PATENTS ARE PENDING
1
1. Before beginning construction, check local building codes regarding footings, location and otherrequirements. Study and understand this owner’s manual.
2. Follow all directions and dimensions carefully.3. Follow the step sequence carefully for correct results.4. Be sure all the parts fit together properly before proceeding.5. SAFETY FIRST: Care must be taken when handling various pieces of your kit since some contain sharp
edges. Wear work gloves, eye protection and long sleeves when assembling or performing anymaintenance on your building.
6. GROUND MUST BE LEVEL: Be sure Floor Frames lie flat on ground. To prepare earth bed, remove sod andother debris. Level the high spots with flat shovel and tamp the bed down. Refer to Page 24 for Parts List.
Site PreparationBefore You Begin
Foundation RecommendationsLocal building codes vary by region, refer to your local codes for specifications.
Concrete Slab1. Select level site for building.
2. Remove 6” of soil for slab.
3. Compact 4” gravel in hole.
4. Place 6 ml plastic over gravel.
5. Construct 2 x 4 form.
6. Pour concrete and level.
Wood Platform1. Construct with 2 x 4 treated lumber and 5/8” minimum exterior grade
plywood using galvanized nails.
2. Level platform.
68 1/2” (174cm)
56 1
/2”
(14
3,5c
m)
Slab Dimensions
Door Opening
16” Centers
68 1/2” (174cm)
56 1
/2”
(14
3,5c
m)
Door Opening
CAUTIONSharp Edges
BASIC TOOLS
No. 2 PhillipsScrewdriver Pliers Work
Gloves
TapeMeasure
Level
Shovel
RubberMallet
2
Do Not store swimming pool chemicals in your building.Combustibles and corrosives must be stored in air tight
containers.
Care & Maintenance
Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch up scratches as soonas you notice them on your building. Immediately clean the area with a wire brush; wash it and applytouch up paint per manufacturer’s recommendation.
Roof: Keep roof clean of leaves and snow with long handled, soft bristled broom. Heavy amounts ofsnow on roof can damage the building making it unsafe to enter.
Doors: Keep doors closed to prevent wind damage.
Fasteners: Regularly check you building for loose screws, bolts, nuts, etc. and retighten them as necessary.
Moisture: With changing temperatures, condensation will accumulate inside the building.
Other Tips: A noncorrosive caulking is helpful to seal the building.
A
B
Raise Panel at Angle
Overlap Panels and align endsHook edge of top Panel
to bottom Panel
C
3
Step 1 Pre-Assembly Side WallsPart No Name Quantity
10307 Wall Panel 810268 Corner Panel 2
ASSEMBLY COMMON FOR ALL PANELS
CAUTIONSharp Edges
ARROW TO TOP
21
NOTE: ALWAYS COVER THE ARROW!
MAKE TWO (2) SIDE WALL SECTIONS4 Panels & 1 Corner - Each
IMPORTANT
MUST USE FLAT SOLID SURFACEDO NOT SNAP ON GROUND OR GRASS!
Bring Top Panel down flat while maintainingpressure in the middle to keep edge hooked
Push down to snap Panels together workingfrom the center outward in both directions
D E
F G
Start in middle ofassembly to snap panels
together
Push down to snap end ofpanels together
Pre-Assembly Side Walls . . . .cont
4
Apply pressure inarea shown
CAUTIONSharp Edges
IMPORTANT
MUST USE FLAT SOLID SURFACEDO NOT SNAP ON GROUND OR GRASS!
5
Pre-Assembly Side Walls. . . . cont
Install Corner PanelH
CAUTIONSharp Edges
ARROW TO TOP
Push down to snapPanels together
working from thecenter in each direction
3
Cover Arrow onCorner Panel
1
Use edge of surface toallow Corner Panel
to hang down
2
I
J K
Align Channel to PanelRibs and pop intoplace at corner
Continue aligningChannel
and popping into place
6
Pre-Assembly Side Walls. . . . contPart No Name Quantity
10261 Upper Channel (painted) 2
Upper Channel(painted)
2
CAUTIONSharp Edges
ARROW TO TOP
Attach Upper Channel(painted)
Channel
CornerPanel
Corner must be against45° cut on Channel
-IMPORTANT-START ASSEMBLY AT CORNER PANEL
7
L
MAKE TWO (2) SIDE WALL SECTIONS
Floor Channel is Unpainted
Attach Floor Channelin the same sequence
as Upper Channel.
Pre-Assembly Side Walls . . . .contPart No Name Quantity
10255 Floor Channel (unpainted) 210280 Corner Clip 4
M
M Insert Corner Clip
Insert Corner Clip
CAUTIONSharp Edges
Channel
CornerPanel
START ASSEMBLY AT CORNER PANEL
Corner must be against45° cut on Channel
-IMPORTANT-
8
Step 2 Pre-Assembly Rear Wall
A
B
Part No Name Quantity
10307 Wall Panel 510268 Corner Panel 1
Install Corner Panel
5 Panels and 1 Corner
2 CAUTIONSharp Edges
ARROW TO TOP
MAKE ONE (1) REAR WALL SECTION
ARROW TO TOP
IMPORTANT
MUST USE FLAT SOLID SURFACEDO NOT SNAP ON GROUND OR GRASS!
9
Attach Upper Channel (Painted)
Pre-Assembly Rear Wall . . . .cont
C
Part No Name Quantity
10262 Upper Channel (painted) 110256 Floor Channel (unpainted) 110280 Corner Clip 2
Attach Floor Channel (unpainted) in the same sequence as Upper Channel.
Insert Corner Clip
Insert Corner Clip
D
D
CAUTIONSharp Edges
2
Channel
CornerPanel
Corner must be against 45° cut onChannel
START ASSEMBLY AT CORNER PANEL-IMPORTANT-
Channel
CornerPanel
START ASSEMBLY AT CORNER PANEL
Corner must be against45° cut on Channel
-IMPORTANT-
E
10316
10317
10
Step 3 Pre-Assembly Front Wall
A Assemble Door Jambs to Wall PanelsInstall Bolt, Washer & Nut in each Door Jamb
Door Jambs always on top of Panel
BInstall Corner Panel
Wall Panel on topof Corner Panel
CAUTIONSharp Edges
Part No Name Quantity
10316 Wall Panel -Right 110317 Wall Panel - Left 110373 Door Jamb 210268 Corner Panel 1
2
ARROW TO TOP
2
11
Attach Floor Channel (Unpainted)
Pre-Assembly Front Wall . . . .cont
Attach Upper Channel(Painted)C
DAttach Header Trim (Painted)
Part No Name Quantity
10262 Upper Channel 110263 Header Trim 110256 Floor Channel 110280 Corner Clip 2
8
E
FInsert Corner Clip
FInsert Corner Clip
CAUTIONSharp Edges
2
Channel
CornerPanel
Corner must be against 45° cuton Channel
START ASSEMBLY AT CORNER-IMPORTANT-
Channel
CornerPanel
Corner must be against45° cut on Channel
START ASSEMBLY AT CORNER-IMPORTANT-
12
Step 4 Wall AssemblyPart No Name Quantity
Side Wall Assembly 1Rear Wall Assembly 1
1
2
3
Install Corner ClipLower
A
Make SureEngaged
1
2
3
Install Corner ClipUpper
B
Make SureEngaged
CornerPanel
Side Panel
Corner Clip
CORNER PANELON TOP OF WALL PANEL
CAUTIONSharp Edges
2
13
Wall Assembly . . . .contPart No Name Quantity
Side Wall Assembly 1Front Wall Assembly 1
C
CornerPanel
Side Panel
Corner Clip
CORNER PANELON TOP OF WALL PANEL
Snap Corner Panels to Wall Panel
E
JoinCorner
Inside assembler applies pressureto hold wall firm
Outside assembler snaps cornerpanel to side panel top to bottom
INSIDE INSIDE
1
2
3
Install Corner ClipLower
C
Make SureEngaged
1
2
3
Install Corner ClipUpper
D
Make SureEngaged
DD
D
C
C
CAUTIONSharp Edges
2
14
Step 5 Gable & Ridge Beam Assembly
Install GableBraces onto Gables
C
Part No Name Quantity
10265 Left Gable 210266 Right Gable 210258 Header Angle 110278 Gable Brace 2
8 4
CAUTIONSharp Edges
Snap Gablesonto
Upper Channel
A
1
2
2
Assemble Header AngleB
Gable
HeaderAngle
UpperChannel
HeaderTrim
15
D
E
Assemble Ridge Beam Angleto Ridge Beam
Install Ridge Beam Assembly toGables
Gable & Ridge Beam Assembly . . . .contPart No Name Quantity
10269 Ridge Beam 110312 Ridge Beam Angle 1
6 4
CAUTIONSharp Edges
2
Frame Must Be Square
Align Roof Panels and snap panel ribstogether
16
Step 6 Pre-assembly - Roof
A
BAssemble Roof Channel
onto top and bottom
MAKE TWO (2) ROOF SECTIONS
HOLES
HOLES
Part No Name Quantity
10252 Roof Panel 610250 Roof Panel-Right 210251 Roof Panel-Left 210267 Roof Channel 410320 Roof Fascia 4
8
CAUTIONSharp Edges
10251
10250
2
ARROW TO TOP
Assemble Fascia Trimonto each side
C
10252
1025210252
NOTELarge Holes on
ChannelsFACE DOWN
10251
10251
10250
10250
17
Step 7 Roof Assembly
D
E Install Ridge Cap onRight Roof Section
Assemble Left Roof Sectionto building
Part No Name Quantity
10270 Ridge Cap 1
10
CAUTIONSharp Edges
2
NOTEHOLE POSITIONS
Assemble Right Roof Section,Peak Caps, & Corner Caps
18
Roof Assembly. . . .cont
F
Part No Name Quantity
Peak Cap 2Corner Cap 4 25
Install screws throughRidge Beam and Roof Angle
into Roof Channel
13
Fold Peak Caps
FOLD FOLD
FOLD
CAUTIONSharp Edges
HELPFUL HINT
Gently tap Channel to alignholes with Main Ridge Beam
2
G
Gray Paint
Part No Name Quantity
Padlock Eyelet 1Clip 4
Attach Door Handle& Padlock Eyelet
to Vertical Door Brace
19
Step 8 Door Assembly
A Slide Clips ontoVerticle Door Brace
B
Part No Name Quantity
10361 Vertical Door Brace 110369 Vertical Door Brace 1
Handle 14
10369
10361
CAUTIONSharp Edges
2
INCORRECT! CORRECT!
Installing Clips
1
2
Align Door Panels & snap PanelRibs together
Hole totop
Attach HorizontalDoor Braces
20
Door Assembly . . . .cont
D
EAttach Vertical Door Braces
Part No Name Quantity
10276 Door Panel (1/2) 110308 Door Panel 110309 Door Panel 110275 Door Brace (Horz) 2
4
CAUTIONSharp Edges
2
C
103081030910276
10369
10361
HOLES
HOLES
ARROW TO TOP
21
Door Assembly . . . . cont
Attach DiagonalBraces & install Screws for
Horizontal Braces
G
F Turn Door OVER
H
IInstall Screws
for Diagonal Braces
Part No Name Quantity
10288 Diagonal Door Brace 2
CAUTIONSharp Edges
2 114
Turn Door OVER
22
Door Assembly . . . .cont
JInstall Door Hinges& Padlock Eyelet
KHang Door
Part No Name Quantity
Padlock Eyelet 166718 Hinge 210264 Ramp 1 6
M
Install Ramp
L
Anchor Building(See Step 9)
CAUTIONSharp Edges
122
23
Anchor Kit Model No AK100, SAK100 or 68383
Recommended for usewith concrete foundation.Contains corner gussets,perimeter clips, hardware,1/4” masonry drill bit andinstallation instructions.
It is important that building beanchored after construction.
These are recommended ways of anchoring.
Anchor Kit Model No AK4, SAK4 or 60298
Recommended for use with anysuggested base. Contains 4Anchors with Cable, clamps andinstallation instructions.
Feed Cable through holein Ridge Beam & Ridge
Beam AngleInsert Cable
Step 9 Anchor Building
Turn Anchors into groundclose to building and
attach Cable.
2
Anchor into Wood or ConcreteFor wood platform. Use Decking Screws.For concrete slab. Use Lag Screws.
13”(33.02 cm)
Parts List 6x5
If you find any parts missingduring construction call:
1-800-851-1085
or write:CUSTOMER SERVICE1101 North Fourth Street
Breese, Illinois 62230
www.sheds.com
Keep this Assembly Manual for further reference.24
Dia. No. Part Name Qty Part No.
1 Wall Panel 13 103072 Wall Panel - Right 1 103163 Wall Panel - Left 1 103174 Corner Panel 4 102685 Upper Channel (painted) 2 102616 Floor Channel (unpainted) 2 102557 Upper Channel (painted) 2 102628 Floor Channel (unpainted) 2 102569 Door Jamb 2 10373
10 Header Trim 1 1026311 Ramp 1 1026412 Corner Clip 8 1028013 Left Gable 2 1026514 Right Gable 2 1026615 Header Angle 1 1025816 Gable Braces 2 1027817 Ridge Beam 1 1026918 Ridge Beam Angle 1 1031219 Roof Panel 6 10252
Dia. No. Part Name Qty Part No.
20 Roof Panel (left) 2 1025121 Roof Panel (right) 2 1025022 Roof Channel 4 1026723 Roof Fascia 4 1032024 Ridge Cap 1 1027025 Peak Cap 226 Corner Cap 427 Door Panel (1/2) 1 1027628 Door Panel 1 1030829 Door Panel 1 1030930 Vertical Door Brace 1 1036131 Vertical Door Brace 1 1036932 Horizontal Door Brace 2 1027533 Diagonal Door Brace 2 10288
Please include your Model Number, Part Number,and Part Name
Separate contents of the carton by the part number while reviewing parts list.Check to be sure that you have all the necessary parts for your building.
25
11
1
1 1
11 1 1
1
1
1
1
2
3
4
4
4
4
5
6
5
6
7
8
7
8
9
9
10
11
12
12
12
12
12
12
12
12
1314
1314
15
16
16
17
18
22
222222
23
23
2425
2526
26
26
26
27
2829
31 30
32
32
33
33
2019
1919
2121
2019
1919
6x523
23
Recommended