View
0
Download
0
Category
Preview:
Citation preview
This system is installed to park only one car on the platform and the ground level is left clear for vehicular movements. The system has column arrangement only on one side, generally on the boundary side, leaving the entire driveway clear for passage.
TYPE
Single Column Cantilever
Stacker
MODELS
E2CS/E2CM/E2CB
NO. OF CAR PER UNIT
1 Car
LIFTING CAPACITY
2000 Kg [ Car Weight]
LIFTING TIME
2 m/min
OPERATION
Hydraulic Power Pack, One Cylinder
with Key/Push
button operation.
POWER SUPPLY
415 V, 3 phase, 50 Hz
POWER CONSUMPTION
Up to 0.03 units per operation (approx.)
Specification Table:
MODEL
SYSTEM
PLATFORM
PLATFORM
LOWER CAR
LIFTING
CAR
WIDTH (MM)
WIDTH (MM)
LENGTH (MM)
HEIGHT(MAX)
MECHANISM
CATEGORY
E2CS
2300
1900
4000
2200
Hydraulic
Small Cars
E2CM 2500 2100 4500 2200 Hydraulic
Mid Sized Sedans
E2CB 2500 2300 4500 2200 Hydraulic Large Sedans/
SUV’s
Standard Features:
• Vehicles can be driven across stacks. • One Platform per system.
• Lifting mechanism installed only on one side of the Stack.
• Color scheme for the System will be provided as per the client’s color theme.
• Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability.
•
Compact Power pack system with
enclosed motors and rubber bush fittings for reduced noise levels.
•
Optional Photo sensor for the bottom car to prevent accidental lowering of upper stack.
•
Electromagnetic locking mechanism to prevent unwanted lowering of upper stack.
•
Limit switches to restrict the travel height by auto cutting off the motor.
•
Remote switch box with Key/Push button for easy operation.
•
Emergency Shutdown switch
Requirements from Client:
•
Parking area allotted must be cleared with no obstructions.
•
Additional space to be provided for storing and installing the Power Pack system.
•
While erection of the system client should provide storage facilities for keeping our tools and other valuable parts
of the system.
•
Temporary Electrical connection must be provided at the time of erection and installation of the systems.
•
12 Amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the
Main Power supply to the parking systems with 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).
•
Incoming Cable Size should be at
least 4 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to
Control Panel.
•
Civil work as foundation for Cantilever
parking system must be done at allotted area prior to installation
as per our Foundation drawing.
•
Foundation Concrete shall be of RCC and minimum M25 strength.
•
In case of Parking Installed
in open to Sky location, it is recommended to have a weather covering over the installation to
prevent damage to the electronics / mechanism due to weathering.
CANTILEVER STACKER (E2CS/CM/CB)
Note: All Sizes can be varied as per client requirements and site conditions.
L TP A R K I N G S Y S T E M S
FOUR LEVEL STACK WITH TWO PIT LEVEL (E4BS(-2)/BM(-2)/BB(-2)) This system offer parking for Four cars with two above the ground level and Two cars in the Pit. For removing
the car parked on the first Pit level Ground level car must be removed
and for removing the
car in the second
Pit level both cars above the ground to be removed. Please Note
:-
Maximum height of the pit level depends upon the clear height above the ground level
Specification Table:
Standard Features:
•
Four
Platforms per system.
•
Color scheme for the System can
be provided as per the Client's requirement.
•
Hot dipped Galvanized Corrugated floor plates on platforms to reduce dead weight and increase durability.
•
Two sets of hydraulic cylinders will be provided.
•
Chain supported balancing and lifting Mechanism
•
Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels.
•
Optional Photo sensor for the middle car to prevent accidental lowering of upper stack or lifting of the lower stack.
•
Electromagnetic locking mechanism to prevent unwanted lowering of upper stacks.
•
Limit switches to restrict the travel height by Auto cutting off the motor.
•
Remote switch box with Key/Push button for easy operation.
•
Emergency Shutdown switch.
Requirements from Client:
•
Parking area allotted must be cleared with no obstructions.
•
Civil work in Pit to be completed with appropriate drainage system provided to prevent water accumulation.
•
Base area
of the parking space allotted shall be Concrete with minimum strength of M20.
•
Pit area provided should be clean and free of any accumulated water.
•
Appropriate lighting to be provided within the pit and working area.
•
Additional space to be provided for storing and installing the Power Pack system.
•
While erection of the system client should provide storage facilities for keeping our tools and other valuable parts of the system.
•
Temporary Electrical connection must be provided at the time of erection and
installation of the systems.
•
12 amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the
Main Power supply to the parking systems with 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).
• Incoming Cable Size should be at least 5 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch
to Control Panel.• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the
installation to prevent damage to the electronics / mechanism due to weathering.
TYPE
MODELS
NO. OF CAR PER UNIT
LIFTING CAPACITY
LIFTING TIME
OPERATION
POWER SUPPLY
POWER CONSUMPTION
Four level Stack with Two pit level
E4BS(-2)/E4BM(-2)/E4BB(-2)
4 Cars
2000 Kg [ Per Car Weight]
2 m/min
(each stack)
Hydraulic Power Pack, Two Cylinderwith Key/Push
button operation.
415 V, 3 phase, 50 Hz
Up to 0.03 units per stack operation
(approx.)
MODEL
E3BS
E3BM
E3BB
SYSTEM DIMENSION
(MM)
2300 X 4500
2500 X 5500
ALL LEVEL
1900mm
ALL LEVEL2100mm
PLATFORM
MAXIMUM LIFTING
CAR
LENGTH (MM)
TRAVEL (MM) MECHANISM
CATEGORY
MAX -
4100mm
ALL LEVEL2100mm
Hydraulic
Small Cars
MAX – 5100mm
Hydraulic ALL LEVEL
2100mmSmall Cars/
Mid Sized Sedans
2800 X 5600 ALL LEVEL
2400MM
MAX – 5200mm ALL LEVEL
2100mmHydraulic
Mid Sized Sedan/
Small Cars/Large Sedans/
SUV’s
Note: All Sizes can be varied as per client requirements and site conditions for appropriate parking Spaces and Pit Dimensions.
L TP A R K I N G S Y S T E M S
PLATFORM
WIDTH
L TP A R K I N G S Y S T E M S
PUZZLE PARKING SYSTEM WITH PIT (EXPS(-Y)/PM(-Y)/PB(-Y))
Note : X is the number of levels in the system above ground and Y is the levels in the Pit. Maximum usable length shall be total length minus 1400mm
TYPE Puzzle Parking with Pit
MODELS
NO. OF EMPTY SLOTS Number of Levels above ground Minus 1 (X-1)
LIFTING CAPACITY 2000 Kg [ Per Car Weight]
LIFTING TIME 1-2 minute per platform (variable)
SLIDING TIME 10 m/min per Platform
OPERATION
Upto 5 level Traction lifting, more than that Hydraulic Lifting, Lower Stack Sliding Eether Side With Motor Chain Mechanism. Integrated System with Touch Screen / Keyboard operation.
POWER SUPPLY 415 V, 3 phase, 50 Hz
POWER CONSUMPTION Up to 0.03 units per Stack Lifting and 0.01 units per sliding operation (approx).
Standard Features: • Fast and automatic retrieval of cars from the parking space without removing any cars parked on the ground level
of the system. • One slot left empty at each level to make way for the upper platform. • Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability. • Geared motor with minimum Safety factor of 2 with manual brake release. • Motor - Chain operated Sliding Mechanism. • Single Power Pack per system to reduce cost in case of hydraulic puzzle • Complete system monitored by PLC for smooth and error free automation. • Back up Limit switches provided for each slot for duplex safety. • Fabricated barriers provided on each platform to provide safety against unwanted lowering. • Fully automatic integrated operation. • Emergency Shut Down switch. • Optional Touch Screen/Numerical Keyboard operation Panel..
Requirement from Client: • Parking area allotted must be cleared with no obstructions.
• Civil work in Pit to be completed with appropriate drainage system provided to prevent water accumulation causing rusting of
the framing. • Pit area to be provided with adequate lighting.
• During erection of the system client should provide storage facilities for keeping our tools and other valuable parts
of the system. • Temporary Electrical connection must be provided at the time of erection and installation of the systems.
• 30 Amps ELCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided the from
Main Power supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E). • Incoming Cable Size should be at least 5 Core x 4sq. mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to Control Panel.
• Civil work as foundation for parking system must be done at stack parking allotted area prior to Installation as per our drawings. • Base area of the parking space allotted shall be Concrete with minimum strength of M20.
• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the installation to prevent damage to the electronics / mechanism due to weathering.
This is an automated system in which no car needs to be removed for removing other car parked on the system thus making each platform independent of the other. This system can be spread horizontally for upto 10 columns and vertically for upto 10 levels and upto Three levels in the pit. Number of slots that needs to be left empty = X-1 (where X is the number of levels).
EXPS(-Y)/EXPM(-Y)/EXPB(-Y)
L TP A R K I N G S Y S T E M S
PUZZLE PARKING SYSTEM (EXPS/PM/PB)
Note : X is the number of levels in the system. Maximum usable length shall be total length minus 1400mm
TYPE Multi Level Puzzle Parking
MODELS EXPS/EXPM/EXPB
NO. OF EMPTY SLOTS Total number of levels minus one (X-1)
LIFTING CAPACITY 2000 Kg [ Per Car Weight]
LIFTING TIME 1.2 minutes per platform (variable)
SLIDING TIME 15 - 25 Seconds per Platform
OPERATION Upto 5 level Traction lifting, more than that Hydraulic Lifting, Lower Stack Sliding Eether Side With Motor Chain Mechanism. Integrated System with Touch Screen/ Keyboard operation.
POWER SUPPLY 415 V, 3 phase, 50 Hz
POWER CONSUMPTION Up to 0.05 units per Stack Lifting and 0.01 units per sliding operation (approx).
Standard Features: • Fast and automatic retrieval of cars from the parking Space without removing any cars parked on the ground level
of the system. • One Slot left empty at each level to make way for the upper platform to pass through. • Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability. • Geared motor with minimum Safety factor of 2 with manual brake release. • Motor- Chain operated Sliding Mechanism. • Single Power Pack per system to reduce cost in case of hydraulic puzzle • Complete system monitored by PLC for smooth and error free automation. • Back up Limit switches provided for each slot for duplex safety. • Fabricated barriers provided on each platform to provide safety against unwanted lowering. • Fully automatic integrated operation. • Emergency Shut Down switch. • Optional Touch Screen/Numerical Keyboard operation Panel.
Requirements from Client: • Parking area allotted must be cleared with no obstructions.
• While erection of the system client should provide storage facilities for keeping our tools and other valuable
parts of the system. • Temporary Electrical connection must be provided at the time of erection and installation of the systems.
• MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the Main Power
supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth(3Ph+N+E) as per our specifications. • Civil work as foundation for parking system must be done at stack parking allotted area prior to installation as per the
foundation plan submitted by us. • Base area of the parking space allotted shall be Concrete with minimum strength of M20.
• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the installation to
prevent damage to the electronics / mechanism due to weathering.
This is an automated system in which no car needs to be removed for removing other car parked on the system thus making each platform independent of the other. This system can be spread horizontally for upto 10 columns and vertically for upto 10 levels. number of slots that needs to be left empty = X-1 (where X is the number of levels).
THREE LEVEL SIMPLE STACKER (E3SS/SM/SB) This is Parking System offers parking for 3 cars; one on the ground and two on the two upper levels. The car
on the ground level will need to be removed before lowering the first level platform; similarly the ground and
first level cars will need to be removed before lowering the second level platform.
TYPE Three Level above Ground Stacker
MODELS E3SS/E3SM/E3SB
NO. OF CAR PER UNIT 3 Cars
LIFTING CAPACITY 2000 Kg [ Per Car Weight]
LIFTING TIME 2 m/min each stack
OPERATION Hydraulic Power Pack, One/Two Cylinder with Key/Push button operation.
POWER SUPPLY
415 V, 3 phase, 50 Hz
POWER CONSUMPTION Up to 0.04 units per stack operation (approx).
Specification Table:
MODEL
SYSTEM
PLATFORM
PLATFORM
LOWER CAR
LIFTING
CAR
DIMENS (MM)
WIDTH (MM)
LENGTH (MM)
HEIGHT(MAX)
MECHANISM
CATEGORY
2300 X 4500
ALL LEVEL
MAX – 2100 Small Cars
Level 2 – 1700
Level 1 – 1900 Gr.level –2000
2500 x 5500
Level 2 – 1900 Small Cars/
Level 1 – 2100 ALL LEVEL
MAX - 2100 Mid Sized Sedans
Gr.level –2200
Hydraulic /
Motorized
Level 2 – 2000 Mid Sized Sedan/
E3SS
E3SM
E3SB Small Cars/
Level 1 – 2200
Level 2 – 3700 Level 1 – 4000
Level 2 – 4000 Level 1 – 4500
ALL LEVEL MAX - 2100 Large Sedans/
Standard Features: • Two platforms per system. • Colour scheme for the System can be provided as per the client’s colour theme. • Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability.
• Chain supported balancing and lifting Mechanism. • Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels.
• Optional Photo sensors for the middle and bottom car to prevent accidental lowering of upper stacks.
• Electromagnetic locking mechanism to prevent unwanted lowering of upper stacks.
• Limit switches to restrict the travel height by cutting of the motor.
• Remote switch box with Key/Push button for easy operation.
• Emergency Shutdown switch.
Requirements from Client: •
Parking area allotted must be cleared with no obstructions.
•
Additional space to be provided for storing and installing the Power Pack system.
•
One end of the stacker to be provided with a rigid support to prevent yawing of the stacker from top.
•
While erection of the system client should provide storage facilities for keeping our tools and other valuable parts of the system.
•
Temporary Electrical connection must be provided at the time of erection and installation of the systems.
•
12 amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the
Main Power supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).
•
Incoming Cable Size should be at
least 5 Core x
2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to
Control Panel.
•
Civil work as foundation for stack parking system must be done at stack parking allotted area prior to installation.
•
Base area of the parking space allotted shall be Concrete with minimum strength of M20.
•
In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the installation to
prevent damage to the electronics / mechanism due to weathering. L TP A R K I N G S Y S T E M S
2700 x 5500Hydraulic / Motorized
Gr.level –2400
SUV’s
Note: All Sizes can be varied as per client requirements and site conditions.
Hydraulic /
Motorized
Level 2 – 4000 Level 1 – 4500
THREE LEVEL STACK
WITH ONE PIT LEVEL (E3BS/BM/BB)
This system offer parking for three cars one on the ground level, one level above ground and one car in the
Pit. For removing the car parked on the first level or the Pit level, Ground level car must be removed.
Please Note
:-
Maximum height of the pit level depends upon the clear height above the ground level
Specification Table:
TYPE
Three level Stack
with one pit level
MODELS
E3BS/E3BM/E3BB
NO. OF CAR PER UNIT
3 Cars
LIFTING CAPACITY
2000 Kg [ Per Car Weight]
LIFTING TIME
2 m/min
(each stack)
OPERATION
Hydraulic Power Pack, Two Cylinder
with Key/Push
button operation.
POWER SUPPLY
415 V, 3 phase, 50 Hz
POWER CONSUMPTION
Up to 0.03 units per stack operation (approx.)
MODEL
SYSTEM DIMENSION
PLATFORM
PLATFORM
MAXIMUM
LIFTING
CAR
(MM) WIDTH (MM)
LENGTH (MM)
TRAVEL (MM)
MECHANISM CATEGORY
2300 X 4500
2500 X 5500
2700 X 5500
MAX - 4100
E3BS
Hydraulic
E3BM
MAX – 5100 Hydraulic
MAX – 5200 E3BB) Hydraulic
Note: All Sizes can be varied as per client requirements and site conditions for appropriate parking Spaces and Pit Dimension
Standard Features:
• Three Platforms per system.
• Color scheme for the System can
be provided as per the Client's requirement. • Hot dipped Galvanized Corrugated floor plates on platforms to reduce dead weight and increase durability.
• Two sets of hydraulic cylinders will be provided. • Chain supported balancing and lifting Mechanism
• Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels. • Optional Photo sensor for the middle car to prevent accidental lowering of upper stack or lifting of the lower stack.
• Electromagnetic locking mechanism to prevent unwanted lowering of upper stacks.
• Limit switches to restrict the travel height by Auto cutting off the motor.
• Remote switch box with Key/Push button for easy operation.
• Emergency Shutdown switch.
Requirements from Client:
• Parking area allotted must be cleared with no obstructions.
• Civil work in Pit to be completed with appropriate drainage system provided to prevent water accumulation.
• Base area of the parking space allotted shall be Concrete with minimum strength of M20.
• Pit area provided should be clean and free of any accumulated water.
• Appropriate lighting to be provided within the pit and working area.
• Additional space to be provided for storing and installing the Power Pack system.
• While erection of the system client
should provide storage facilities for keeping our tools and other valuable parts of the system.
• Temporary Electrical connection must be provided at the time of erection and installation of the systems.
• 12 amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the
Main Power supply to the parking systems with 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).
• Incoming Cable Size should be at
least 5 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to Control Panel.
• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the
installation to prevent damage to the electronics / mechanism due to weathering.
L TP A R K I N G S Y S T E M S
Small Cars
Small Cars/ Mid Sized Sedans
Mid Sized Sedan/
Small Cars/ Large Sedans/
SUV’s
ALL LEVEL 2000mm
ALL LEVEL2200mm
ALL LEVEL2400MM
ALL LEVEL2100mm
ALL LEVEL2100mm
ALL LEVEL2100mm
TOWER PARKING SYSTEM (ETPS-X/TM-X/TB-X)
Note : X is the number of Cars in the system.
Maximum usable length shall be total length minus 1700 mm
TYPE
Motorized Tower parking System
MODELS
ETPS-X, ETPM-X, ETPB-X
NO. OF EMPTY SLOTS
Entire Centre Column left Empty
LIFTING CAPACITY
2500 Kg [ Per Car Weight]
LIFTING TIME Upto 60m per minute max (variable)
SLIDING TIME 15 -
25
Seconds per Platform
OPERATION
Down collective lifting mechanism with counter weight,
Sliding either Side with Motor Chain
Mechanism. Integrated System with Touch Screen/ Keyboard operation.
POWER SUPPLY
415 V, 3 phase, 50 Hz
POWER CONSUMPTION
Up to 0.07
units per Operation
and 0.01 units per sliding operation (approx).
Standard Features:
Requirements from Client:
•
Parking area allotted must be cleared with no obstructions.
•
While erection of the system client
should provide storage facilities for keeping our tools and other valuable
parts of the system.
•
Temporary Electrical connection must be provided at the time of erection and installation of the systems.
•
MCB and Main Electrical Connection (or 4 Pole RCBO)
along with electrical cable fitting must be provided from the Main Power
supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth(3Ph+N+E)
as per our specifications.
•
Civil work as foundation for stack parking system must be done at stack parking allotted area prior to installation
as per the foundation plan submitted by us.
•
If the system to be installed in the RCC shaft, hooks to be provided on the top as per our drawings.
•
In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the installation to
prevent damage to the electronics / mechanism due to weathering.
L TP A R K I N G S Y S T E M S
Tower parking is a system wherein upto 60 cars can be parked in a space of 3 cars. Having a lift working up and down in the centre transporting the vehicles to their designated slots vertically. This system can have 5 columns Horizontally and can go upto 30 levels high.
• Fast and automatic retrieval of cars from the parking Space without removing any cars parked on the ground level of the system.
• High speed Geared motors with counter weight and Guides for smooth lift and lowering.
• Turntable on the ground level for getting the car in the Drive out position
• Motor- Chain operated Sliding Mechanism.
• Complete system monitored by PLC for smooth and error free automation.
• Back up Limit switches provided for each slot for duplex safety.
• Robust Steel structure.
• Fully automatic integrated operation.
• Emergency Shut Down switch.
• Optional Touch Screen/Numerical Keyboard / RFID Swipe card operation Panel.
TWO LEVEL SIMPLE STACKER (E2SS/SM/SB) This is a two level parking system, where one car is parked on the ground level and one on the platform. The car on the ground level will need to be removed for lowering and removing the car parked on the platform.
Specification Table:
Note: Sizes can be varied as per client requirements and site conditions.
Standard Features: • Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability. • Color scheme for the System will be provided as per the Client's requirement. • Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels.
• Optional Photo sensor for the bottom car to prevent accidental lowering of upper stack. • Electromagnetic locking mechanism to prevent unwanted lowering of upper stack. • Limit
switches to restrict the travel height by auto cutting off the motor.
• Remote switch box with Key/Push button for easy operation.
• Emergency Shutdown switch.
Requirements from Client:
• Parking area allotted must be cleared with no obstructions.
•
During the erection of the system client should provide storage facilities for keeping our tools and other valuable parts of the system.
• Additional space to be provided for storing and installing the Power Pack system
•
Temporary Electrical connection must be provided at the time of erection and installation of the systems.
•
12 Amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the
Main Power supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).
•
Incoming Cable Size should be at least
5 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to Control Panel.
•
Civil work as foundation for stack parking system must be done at stack parking allotted area prior to installation.
•
Base area of the parking space allotted shall be Concrete with minimum strength of M20.
•
In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the
Installation to prevent damage to the electronics / mechanism due to weathering.
TYPE
MODELS
NO. OF CAR PER UNIT
LIFTING CAPACITY
LIFTING TIME
OPERATION
POWER SUPPLY
POWER CONSUMPTION
Two Level Single Stacker
E2SS/E2SM/E2SB
2 Cars
2000 Kg [ Car Weight]
2 m/min
Hydraulic Power Pack, One Cylinder with Key/Push Button Operation
415 V, 3 phase, 50 Hz
Up to 0.03 units per operation (approx.)
MODEL SYSTEM PLATFORM PLATFORM LOWER CAR LIFTING CAR
WIDTH (MM) WIDTH (MM) LENGTH (MM) HEIGHT(MAX) MECHANISM CATEGORY
E2SS
E2SM
E2SB
2300
2500
2700
2000
2200
2400
4000
4000
4500
2100
2100
2100
Hydraulic
Hydraulic
Hydraulic
Small Cars
Mid Sized Sedans
Large Sedans/SUV's
L TP A R K I N G S Y S T E M S
THREE LEVEL STACK WITH TWO PIT LEVEL (E3BS(-2)/BM(-2)/BB(-2))
Specification Table:
Note: All Sizes can be varied as per client requirements and site conditions for appropriate parking Spaces and Pit Dimensions.
Standard Features:
• Three Platforms per system.
• Color scheme for the System can
be provided as per the Client's requirement.
• Hot dipped Galvanized Corrugated floor plates on platforms to reduce dead weight and increase durability.
• Two sets of hydraulic cylinders will be provided.
• Chain supported balancing and lifting Mechanism
• Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels.
• Optional Photo sensor for the middle car to prevent accidental lifting of or lowering stack.
• Electromagnetic locking mechanism to prevent unwanted lowering of upper stacks.
• Limit switches to restrict the travel height by Auto cutting off the motor.
• Remote switch box with Key/Push button for easy operation.
• Emergency Shutdown switch.
Requirements from Client:
• Parking area allotted must be cleared with no obstructions.
• Civil work in Pit to be completed with appropriate drainage system provided to prevent water accumulation.
• Base area of the parking space allotted shall be Concrete with minimum strength of M20.
• Pit area provided should be clean and free of any accumulated water.
• Appropriate lighting to be provided within the pit and working area.
• Additional space to be provided for storing and installing the Power Pack system.
• While erection of the system client should provide storage facilities for keeping our tools and other valuable parts of the system.
• Temporary Electrical connection must be provided at the time of erection and installation of the systems.
• 12 amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the
Main Power supply to the parking systems with 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).
• Incoming Cable Size should be at least 5 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch
to Control Panel.• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the
installation to prevent damage to the electronics / mechanism due to weathering.
MODEL
SYSTEM DIMENSION
PLATFORM
PLATFORM
MAXIMUM
LIFTING
CAR
(MM) WIDTH (MM)
LENGTH (MM)
TRAVEL (MM)
MECHANISM CATEGORY
2300 X 4500
2500 X 5500
2700 X 5500
MAX - 4100
E3BS
Hydraulic
E3BM
MAX – 51 00 Hydraulic
MAX – 5200 E3BB) Hydraulic
Small Cars
Small Cars/ Mid Sized Sedans
Mid Sized Sedan/
Small Cars/ Large Sedans/
SUV’s
ALL LEVEL 2000mm
ALL LEVEL2200mm
ALL LEVEL2400MM
ALL LEVEL2100mm
ALL LEVEL2100mm
ALL LEVEL2100mm
TYPE Three level Stack with Two pit level
MODELS E3BS(-2)/E3BM(-2)/E3BB(-2)
NO. OF CAR PER UNIT 3 Cars
LIFTING CAPACITY
2000 Kg [ Per Car Weight]
LIFTING TIME
2 m/min
(each stack)
Hydraulic Power Pack, Two Cylinderwith Key/Push
button operation.
POWER SUPPLY
415 V, 3 phase, 50 Hz
POWER CONSUMPTION
Up to 0.03 units per stack operation
(approx.)
OPERATION
L TP A R K I N G S Y S T E M S
This system offer parking for three cars with one on the ground level and Two cars in the Pit. For removing the car parked on the first Pit level Ground level car must be removed and for removing the car in the second Pit level all cars above to be removed. Please Note :- Maximum height of the pit level depends upon the clear height above the ground level
Recommended