Bulk Cargo- Other Than Grain

7/28/2019 Bulk Cargo- Other Than Grain

1/10

http://thenauticalsite.com/nauticalnotes/cargowork/mycargowk-lesson05-bulknotgrain.htm

Cargo Work

Bulk Cargo (Not Grain)

Bulk cargoes (other than grain)

The officer of the watch should know the pre-planned loading procedure regardingquantities to be loaded in each space, the order of deballasting tanks and shifting the

vessel under loading chutes. The procedure will have been worked out to keep stresses

within acceptable limits and to finish with a satisfactory weight distribution and trim.

The officer of the watch should see that the plan is followed, particularly at berths

with only one loading chute, to avoid over-stressing the ship.

Code of Safe Practice for Solid Bulk Cargoes BC Code is intended to set a standard for the safe

stowage and carriage of solid bulk cargoes.

This Code is a recommended guide for ship owners, shippers and masters and shall apply to all

shipments of bulk cargoes.

The list of products appearing in the Appendices of the BC Code, however, is by no means

exhaustive. Consequently, before any bulk cargo is loaded, it is essential to ascertain (normally

from the shipper) the current physical and chemical properties of the cargo, as required under

SOLAS Chapter VI.

General requirements

Before and during loading, transport and unloading of bulk cargoes, all necessary safety

precautions including any regulations or requirements should be observed, including the

following:

1. Dangerous Bulk Material Regulations

2. Safe Working Practices Regulations

3. International Maritime Dangerous Goods Code (IMDG Code)

4. Emergency Procedures For Ships Carrying Dangerous Goods

5. Medical First Aid Guide for Use in Accidents Involving Goods (MFAG)

7/28/2019 Bulk Cargo- Other Than Grain

2/10

6. IMO BC Code - Code of Safe Practice for Solid Bulk Cargoes

Poisoning and asphyxiation hazards

Certain bulk cargoes are liable to oxidation, which in t urn may result in oxygen depletion,

emission of toxic fumes and self-heating. Other bulk cargoes may not oxidize but may emit toxic

fumes.

It is important therefore that the shipper inform the master before loading of the existence of any

chemical hazards. The master should refer to Appendix B of the BC Code and take the necessary

precautions, especially those pertaining to ventilation.

Certain cargoes may emit toxic gases when wetted. In these cases the ship should be provided

with the appropriate gas detection equipment.

A flammable gas detector is only suitable for testing the explosive nature of gas mixtures.

Emergency entry into a cargo space should be undertaken only by trained personnel wearing

self-contained breathing apparatus, and protective clothing if considered necessary, always under

the supervision of a responsible officer.

In the event of emergency entry into a cargo space, in addition to the above requirement, spare

self-contained breathing apparatus, safety belts and safety lines should be readily available.

Health hazard from dust

To minimize the chronic risks from exposure to the dust of certain materials carried in bulk, a

high standard of personal hygiene for those exposed to the dust cannot be too strongly

emphasized. The precautions should include not only the use of appropriate protective clothing

and barrier creams when needed but also adequate personal washing especially before meals, and

laundering of outer clothing.

Flammable atmosphere

Dust created by certain cargoes may constitute an explosion hazard, especially, during loading,

unloading and cleaning. This risk can be minimized at such times by ensuring that ventilation is

sufficient to prevent the formation of a dustladen atmosphere and by hosing down rather than

sweeping.

CARGOES THAT MAY LIQUEFY (section 7 of the BC Code)

Properties, characteristics and hazards

Cargoes that may liquefy include concentrates, certain coals and other materials having similar

physical properties. Appendix A of the BC Code contains a list of such cargoes, which generallyconsist of a mixture of small particles in contrast with natural ores that include a considerable

percentage of large particles or lumps.

Section 5 of the BC Code - Trimming Procedures

At moisture content above that of the transportable moisture limit, shift of cargo may occur as a

result of liquefaction.

7/28/2019 Bulk Cargo- Other Than Grain

3/10

The major purpose of the sections of this Code dealing with these cargoes is to draw the attention

of masters and others to the latent risk of cargo shift, and to describe the precautions deemed

necessary to minimize this risk.

Such cargoes may appear to be relatively dry and granular when loaded, but may contain

sufficient moisture as to become fluid under the stimulus of compaction and the vibration that

occurs during a voyage.

In the resulting viscous fluid state, cargo may flow to one side of the ship when it rolls one way,

but not completely return when it rolls the other. Thus, the ship sways progressively until it

reaches a dangerous heel and capsizes.

To prevent subsequent shifting, and also to decrease the effects of oxidation of material with a

predisposition to oxidize, these cargoes should be trimmed reasonably level on completion of

loading, irrespective of the angle of repose.

7/28/2019 Bulk Cargo- Other Than Grain

4/10

Amended Extract from SOLAS Chapter VI

Part B

Special provisions for bulk cargoes other than grain

Regulation 6

Acceptability for shipment

Concentrates or other cargoes which may liquefy shall only be accepted for loading when the

actual moisture content of the cargo is less than its transportable moisture limit. However, such

concentrates and other cargoes may be accepted for loading even when their moisture content

exceeds the above limit, provided that safety arrangements to the satisfaction of the

Administration are made to ensure adequate stability in the case of cargo shifting and further

provided that the ship has adequate structural integrity.

Prior to loading a bulk cargo which is not a cargo classified but which has chemical properties

that may create a potential hazard, special precautions for its safe carriage shall be taken.

Regulation 7

Loading, unloading and stowage of bulk cargoes

To enable the master to prevent excessive stresses in the ships structure, the ship shall be

provided with a booklet, which shall be written in a language with which the ships officers

responsible for cargo operations are familiar. The booklet shall, as a minimum, include:

.1 stability data,

.2 ballasting and de-ballasting rates and capacities;

.3 maximum allowable load per unit surface area of the tank top plating;

.4 maximum allowable load per hold;

.5 general loading and unloading instructions with regard to the strength of the ships structure

including any limitations on the most adverse operating conditions during loading, unloading,

ballasting operations and the voyage;

.6 any special restrictions such as limitations on the most adverse operating conditions imposed

by the Administration or organization recognized by it, if applicable; and

.7 where strength calculations are required, maximum permissible forces and moments on the

ships hull during loading, unloading and the voyage.

Before a solid bulk cargo is loaded or unloaded, the master and the terminal representative shall

agree on a plan* which shall ensure that the permissible forces and moments on the ship are notexceeded during loading or unloading, and shall include the sequence, quantity and rate of

loading or unloading, taking into consideration the speed of loading or unloading, the number of

pours and the de-ballasting or ballasting capability of the ship. The plan and any subsequent

amendments thereto shall be lodged with the appropriate authority of the port State.

7/28/2019 Bulk Cargo- Other Than Grain

5/10

Bulk cargoes shall be loaded and trimmed reasonably level, as necessary, to the boundaries of

the cargo space so as to minimize the risk of shifting and to ensure that adequate stability will be

maintained throughout the voyage.

When bulk cargoes are carried in tween-decks, the hatchways of such tween-decks shall be

closed in those cases where the loading information indicates an unacceptable level of stress of

the bottom structure if the hatchways are left open. The cargo shall be trimmed reasonably leveland shall either extend from side to side or be secured by additional longitudinal divisions of

sufficient strength. The safe load-carrying capacity of the tween-decks shall be observed to

ensure that the deck-structure is not overloaded.

The master and terminal representative shall ensure that loading and unloading operations are

conducted in accordance with the agreed plan.

If during loading or unloading any of the limits of the ship are exceeded or are likely to become

so if the loading or unloading continues, the master has the right to suspend operation and the

obligation to notify accordingly the appropriate authority of the port State with which the plan

has been lodged. The master and the terminal representative shall ensure that corrective action is

taken. When unloading cargo, the master and terminal representative shall ensure that the

unloading method does not damage the ships structure.

The master shall ensure that ships personnel continuously monitor cargo operations. Where

possible, the ships draught shall be checked regularly during loading or unloading to confirm

the tonnage figures supplied. Each draught and tonnage observation shall be recorded in a cargo

logbook. If significant deviations from the agreed plan are detected, cargo or ballast operations

or both shall be adjusted to ensure that the deviations are corrected.

At a moisture content above that of the transportable moisture limit, shift of cargo may occur as a

result of liquefaction.

Many cargoes may appear to be relatively dry and granular when loaded, but may containsufficient moisture as to become fluid under the stimulus of compaction and the vibration that

occurs during a voyage.

In the resulting viscous fluid state, cargo may flow to one side of the ship when it rolls one way,

but not completely return when it rolls the other. Thus, the ship way progressively reaches a

dangerous heel and capsize.

Ships other than specialist suited ones shall carry only those cargoes having a moisture content

that is not in excess of the transportable moisture limit as defined in this Code.

Specially suited ships

Specially suited ships may carry concentrates having a moisture content in excess of thetransportable moisture limit if the ship possesses a valid document of approval from her

administration, accompanied by such stability information as her administration may require.

The document of approval must clearly state For carriage of concentrates having a moisture

content in excess of the transportable moisture limit.

When concentrates are loaded that have a moisture content in excess of the transportable

moisture limit, the whole surface area of each cargo space shall be trimmed level.

7/28/2019 Bulk Cargo- Other Than Grain

6/10

Cargoes having a moisture content in excess of the flow moisture point shall not be carried in

bulk.

Before loading, the shipper or his appointed agents shall provide to the master and the port

warden, if requested, details, as appropriate, of the characteristics and properties of any material

constituting bulk cargo, such as flow moisture point, stowage factor, moisture content, angle of

repose, chemical hazards, etc. so that any necessary safety precautions can be put into effect.

To do this the shipper shall arrange, possibly in consultation with the producers, for the cargo to

be properly sampled and tested. Furthermore, the shipper should provide the ships master and

the port warden, if requested, with the appropriate certificates of test, as applicable for a given

cargo.

Before and during loading, auxiliary check tests of the moisture content may be carried out using

instruments designed specifically for that purpose, such as the SPEEDY MOISTURE

TESTER. Tests conducted with this instrument indicate a precision of 1% compared with the

laboratory method, i.e., with a laboratory reading of 10%, the SPEEDY reading could range

from, 9% to 11%. If the readings obtained by this method are consistently higher than those

shown on the certificate, loading of the cargo should cease and a further laboratory test be

conducted.

If the master has doubts as regards the appearance of condition of the cargo for safe shipment,

the following auxiliary method may be used on board ship or at the dockside to perform a check

test for approximately determining the possibility of flow:

Half fill a cylindrical can or similar container (0.5-1 litre capacity) with a sample of cargo. Take

the can in one hand and bring it down sharply from a height of about 0.2m to strike a hard

surface such as a solid table. Repeat the procedure twenty-five times at one or two second

intervals. Examine the surface for free moisture or fluid conditions. If free moisture or a fluid

condition appears, make arrangements to have additional laboratory tests on the cargo conducted

before it is accepted for loading.

7/28/2019 Bulk Cargo- Other Than Grain

7/10

COAL is very liable to spontaneous heating. If there is sufficient oxygen available, combustion

is liable to take place. The amount of heating that takes place depends on the type of type coal

and how much heat can be dispersed by ventilating the coal. Ventilation can be a double-edged

weapon as although it takes heat from the coal it also allows unwanted oxygen into the coal. To

keep the coal as cool as possible it should be stowed away from hot bulkheads. To keep oxygen

away from the coal only surface ventilation should be allowed.All spar ceiling or cargo battening should be removed as besides the liability of it to damage, it

can give unwanted air pockets in the coal. Unwanted air may also get into a cargo through a

temporary wooden bulkhead. If such a bulkhead has been constructed all cracks should be

sealed, preferably by pasting paper over both sides of the bulkhead.

Freshly mined coal absorbs oxygen, which, with extrinsic moisture, forms peroxides. These in

turn breakdown to form carbon monoxide and carbon dioxide.

Heat is produced by this exothermic reaction causing further oxidation and further heat. If this

heat is not dissipated ignition will occur. This is called Spontaneous combustion.

As this is essentially a surface reaction the smaller the surface available for the absorption ofoxygen the better. Every attempt should be made to prevent undue breakage of the coal whilst it

is being loaded. It may be noted that 1 MT of coal in an unbroken cube has a surface area of

about 3.72m2, whereas if it is broken up to pass through a 1.5mm mesh screen its surface area is

nearly 4000m2. If a large amount of breakage occurs the small coal with the large surface area is

found in the centre of the hold, whilst the large coal will roll down the sides. This aggravates the

situation, as the large coal gives a good path for air to flow to the smaller coal where the

spontaneous heating is most liable to occur.

Most coal fires in cargo occur at about tween deck level and this is the area where the greatest

attention should be paid to temperature and the restriction of through ventilation.

7/28/2019 Bulk Cargo- Other Than Grain

8/10

The following are recommendations for the carriage of coal.

The ventilators to the lower holds should be so arranged that they might be opened or closed at

will during the voyage.

As the critical temperature at which the process of spontaneous heating in coal becomes greatly

accelerated is in some varieties of coal as low as 36C, and generally is not much higher, the

need of keeping the exteriors surface of the hull, and thereby the interior of the tween decks and

holds, as cool as possible is manifest.

The iron decks of ships carrying coal in the tropics can be covered with dunnage to

lessen heating.Suitable means should be provided for ascertaining from time to time the temperature of the

lower mass of coal, particularly below the hatchways, and this might be done by means of two

pipes leading down to the bottom of the coal at each hatchway.

The temperature tubes should have closed ends to prevent admission of air into the cargo. The

temperature of the coal at three heights should be taken daily.

7/28/2019 Bulk Cargo- Other Than Grain

9/10

Gas from the holds or tween decks space may find its way into shaft, peaks, chain lockers or

similar space unless the bulkheads and casings are maintained in gas tight conditions.

Naked lights should not be used in holds or other spaces in which gas may accumulate until the

spaces have been well ventilated.

Full use should, when necessary, be made of the breathing apparatus or smoke helmet and thesafety lamp, which form part of the ships statutory fire appliances.

The employment of the crew in chipping and painting below decks during the voyage should be

avoided. The danger from smoking should be realized and no oily waste, wood, old rope,

sacking etc. should be left below where it can become ignited by spontaneous heating

On arrival at the port of discharge the hold ventilators should be unplugged and the lower hold

well ventilated before commencing to work cargo.

Coal is frequently loaded from a single tip and earlier it was necessary to drift the vesselfore andaft so that all holds may be filled. To keep these shifts to a minimum No.2 was first put under

the tip.

After about one third the capacity of the hold was loaded the vessel was shifted so that No. 3 was

loaded to about one third of its capacity. Likewise the remaining after holds were loaded and

then the tip was shifted astern to reach No. 1, half the capacity was put in, before shifting to No.

2, which was then filled.

The other after holds were now filled in order excepting the aftermost. The aftermost hold and

the No.1 were now worked so that the vessel would complete loading in a good trim.

Coal is sometimes graded, when this in so, care should be taken to prevent undue breakage.

Lowering the first few truckloads into the hold helps as do control of the rate of tipping down

and chute.

Some ports have conveyor belts and an endless bucket system for loading; this is excellent for

graded coal and also keeps the dust down with the ordinary coal.

Fortunately it is mainly the better coals, which are graded, and in generally these are not so

friable.

Coal will need to be trimmed and its angle of repose is quite high, especially if large coal is

loaded.

There is no danger for coal shifting unless it is the very small stuff known as mud coal, slurry or

duff.

This is very fine coal, almost dust, and if the moisture content is high it behaves almost like aliquid.

7/28/2019 Bulk Cargo- Other Than Grain

10/10