View
2
Download
0
Category
Preview:
Citation preview
BeoVision 10 Guide
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not ope rate normally, or has been dropped.
The mains plug of the power supply cord shall remain readily operable.
Do not expose batteries or battery packs to excessive heat such as sunshine, fire or the like.
Follow instructions to ensure correct and safe installation and interconnection of equipment in multimedia systems.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Do not expose this equip ment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment.
To completely disconnect this equipment from the AC Mains, disconnect the mains plug from the wall socket. The disconnect device shall remain readily operable.
The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of un insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and main tenance (servicing) instructions in the literature accompanying the product.
This guide contains information about the daily use of your Bang & Olufsen product
and connected equipment. We expect your retailer to deliver, install and set up
your product.
On www.bang-olufsen.com you can find further information and relevant FAQs
about your product.
Your Bang & Olufsen retailer is your first stop for all your service queries.
To find your nearest retailer or contact Bang & Olufsen Customer Service, visit our website …
www.bang-olufsen.com
or write to: Bang & Olufsen a/s
BeoCare
Peter Bangs Vej 15
DK–7600 Struer
Dear Customer
3510529 1002
Technical specifications, features and the use thereof are subject to change without notice.
Cautions – Ensure that the television is positioned, set up
and connected in accordance with the instructions in this guide.
– Place your television on a firm, stable surface. To prevent injury, use Bang & Olufsen approved stands and wall brackets only!
– Do not place any items on top of your television. – Do not subject the television to rain, high
humidity or sources of heat. – The television is developed for indoor use in dry,
domestic environments only. Use within a temperature range of 10–35°C (50–95°F), and at an altitude of no more than 1,500 m (5,000 ft).
– Do not place the television in direct sunlight, as this may reduce the sensitivity of the remote control receiver.
– Leave enough space around the television for adequate ventilation.
– Connect all cables before connecting or reconnecting any of the products in your system to the mains.
– No naked flame sources, such as lighted candles should be placed on the apparatus.
– Do not attempt to open the television. Leave such operations to qualified service personnel.
– Do not strike the glass with hard or pointed items.
– The television can only be switched off completely by disconnecting it from the wall socket.
– The supplied mains cord and plug are specially designed for the television. If you change the plug or in any way damage the mains cord, it can affect the TV performance.
Dai
ly u
se
Contents
Daily use
6 How to use your remote control
8 Introduction
10 Operate equipment with Beo4 and Beo5
12 BeoLink system
14 Surround Sound
15 Adjust picture and sound settings
16 Game mode and picture format
17 Sleep Timer and Play Timer
18 Turn the television
Installation and setting up
20 Connect and set up an audio system
22 Connect and set up a BeoLink System
23 Your television in a link room
24 Two televisions in the same room
26 Set up your television
28 Expand your setup
30 Set up additional equipment
32 Connection panels
34 First-time setup of your television
36 Loudspeaker setup
38 Additional settings
39 On-screen menus
39 Cleaning
TV LIGHT RADIO
DTV DVD CD
V MEM RECORD A MEM
7 8 9
4 5 6
TEXT 0 MENU
1 2 3
LIST EXIT
STOP
GO
How to use your remote control
Information 1*Some buttons can be configured during the setup process. See p. 29. NOTE! For general information about remote control operation, see the guide enclosed with your remote control.
Beo4 operation The instructions in this guide are mainly based on Beo4.
In the ‘OPTIONS’ menu, you can bring up the ‘BEO4 SETTING’ menu. This menu is only relevant if you have a Beo4 remote control with a navigation button. See the Beo4 guide or contact your Bang & Olufsen retailer for further information.
BEO4 SETTING menu
Select colour specific functions
Adjust volume To mute, press the middle of the button
The Beo4 display shows you the activated source or function
Accept or store settings
Search backwards or forwards or move in menus
Back up through menus
Standby
Select channels and enter information in on-screen menus
Step through channels or move in menus
Display extra ‘buttons’ on the Beo4 Press repeatedly to change ‘buttons’
Switch on the TV*1
Switch on a connected set-top box
Bring up the main menu of the active source
Exit menus completely
TV
GO
STOP
TV
0 – 9
LIST
MENU
EXIT
DTV
6
STOP PLAY
BACK
Living Room
TV V.MEM RADIO
DTV N.MUSIC N.RADIO
PC DVD CD
Dai
ly u
se
2*About buttons
3*Coloured buttons Actual zone
Soft buttons on Beo5
Light grey buttons indicate that you have to press a text in the display. Dark grey buttons indicate that you have to press a hard button. Press the wheel next to the colour to activate a coloured button. Indicates the actual zone on Beo5 as it was named during the Beo5 configuration process. Depending on the activated source, different soft buttons appear on the screen. Touch the screen to activate the function.
Start playback
Step through channels
Search backwards or forwards or move in menus
Standby
Search backwards or forwards or move in menus
Back up through menus
Soft button, touch screen to select*2
Switch on a source or select a function
Press centre button to accept or store settings
Turn to adjust volume To mute, turn quickly counter-clockwise
Bring up SCENE buttons, such as Zones or Speaker Press again to return
Select colour specific functions*3
Press volume wheel next to the colour
Bring up digits to select channel Press again to return
Back up through Beo5 displays
Exit menus completely
Beo5 operation You can also operate your TV with a Beo5. Where relevant Beo5
operations have been mentioned.
PLAY
STOP
TV
GO
+
BACK
7
Navigate in menus and select settings using your remote control. On page 39 you
will find an overview of the menus in your TV.
Information about the selected source is shown at the top of the screen. On-screen menus allow you to adjust settings.
Display and menus
Introduction
Show menu Switch on TV Switch on connected set-top box
or
Important – for more information: www.bang-olufsen.com Remote control The instructions in this guide are mainly based on the Beo4 remote control, but you can also operate the TV with Beo5.
On the first pages in this guide, you will find an overview of the buttons on Beo4 and Beo5. For general information about remote control operation, see the guide enclosed with your remote control.
TV SETUP
SLEEP TIMER
PLAY TIMER
OPTIONS
select
TV DTV MENU
8
Menu name
Menu options
Information field
Example of on-screen menu
Dai
ly u
se
When a menu is on the screen, you can move between menu options, reveal settings or enter data.
Navigate in menus Select option/setting
Enter data Bring up sub-menu/store setting
Select option Exit menus
or
Move backwards through menus
GO0 – 9 EXIT STOP
9
Operate equipment with Beo4 or Beo5
The built-in Peripheral Unit Controller acts as an interpreter between connected
video equipment, such as a set-top box, recorder or DVD player, and your Bang &
Olufsen remote control.
1*Menu overlay You cannot bring up the overlay in link rooms. Instead, press a
desired coloured button or GO followed by a number.
Using the Beo4 you get quick access to selected function via the menu overlay.
Show menu overlay*1 Select connected equipment Select function
Activate a function without the menu overlay. The connected equipment must be switched on.
Direct Beo4 operation Select function
NOTE! Which source button activates your peripheral unit depends on the settings in the ‘CONNECTIONS’ menu. See p. 32.
Useful hints
Bring up menu overlay or
or
Activate function
GUIDE
MENU
TEXT
INFO
WIDE
1
2
3
4
5
MENU
1–9
10
The Beo4 menu overlay
Dai
ly u
se
Operate a connected equipment’s own menu via the remote control. On Beo4 you may have to press EXIT instead of STOP to return to a previous menu.
Use equipment menus Bring up equipment menu Navigate in
menus
or
Select function Step in pages/channel lists
Enter information
Switch on or off
TV menu
On some connected equipment you have to press GO then 0 to switch the equipment on and off if you have a Beo4. On Beo4 press MENU twice to bring up the TV’s main menu, whene.g. DVD is selected as source.
Use the Bang & Olufsen remote control to gain access to the functions offered
by your non-Bang & Olufsen equipment.
NOTE! See also the guide enclosed with the connected equipment. For further information about supported equipment, contact your Bang & Olufsen retailer.
The main functions of your equipment can be operated via the Beo5 display. Not all functions may be supported.
Beo5 operation Select source Select function
0–9
11
BeoLink system
Useful hints Main room source Link room source
1*Beo4 list of functions
2*Link tuner
This is the central source from which you can distribute sound and pictures to link room sources. This source is placed in the link room and through the source you can receive sound and pictures from connected main room sources. Without a link tuner you can only receive sound, see p. 22. In order to display AV and LINK on Beo4, you must first add it to the Beo4 list of functions. See the guide enclosed with your Beo4. In order to receive picture and sound you need to connect a link tuner to your link room television.
If you have a BeoLink system, you can operate all connected sources from both the
main room and link rooms.
Listen to sound from a TV source on your audio system speakers.
TV sound on the audio speakers
Select audio speaker zone Select video source
Select AV*1 Select video source
Listen to audio sound on the speakers connected to the TV. Only relevant for Option 1-1, see p. 21.
Audio sound on the TV speakers
Select TV speaker zone Select audio source
Select AV*1
Select audio source
Activate a main or link room source from a link room. The source type, for example an audio product, is only present in one of the rooms.
Use a source present in one room*2
Select source Operate source as usual
Select source Operate source as usual
…
LIST TV
TV
…
LIST CD
CD
RADIO
RADIO
12
Dai
ly u
se
Options Changes in link room setup
Audio system
To use all functions properly, the products must be set to the correct Options. See p. 20. If you move your link room products to other rooms, remember to have your Beo5 remote control reconfigured by your Bang & Olufsen retailer. Only Bang & Olufsen audio systems with Master Link support integration with the TV.
Activate a link room source, for example, a TV in a link room when you also have, for example, a TV in the main room.
Use a link room source
Select source Operate source as usual
Select source Operate source as usual
Activate a main room source from a link room even if you have the same source, for example, a TV in the link room.
Use a main room source
Press Select source
Select LINK*1
Select source Operate source as usual
Operate source as usual
TV
TV
LIST TV
TV LINK
13
Link room
Main room
NOTE! If you have added only two front speakers to the TV, you will only be able to choose Speaker 1–3. You can also add a BeoLab sub-woofer to your TV.
1*LIST menu
2*Optimise
In order to display SPEAKER on Beo4, you must first add it to the Beo4 list of functions. The speaker combination is optimised if you press GO on Beo4. On Beo5 press Optimise.
Surround sound
You can select a speaker combination that suits the source you are using.
Select speakers for movie sound The TV automatically selects the optimal sound when you select a source, but you can adjust this setting yourself, using any of the available speaker combinations.
Bring up SPEAKER in your Beo4 display*
1Select speaker combination*
2
Useful hints
1–5
14
Speaker 5 Speaker 1 Speaker 2 Speaker 3 Speaker 4
Dai
ly u
se
Adjust picture and sound settings
Picture and sound settings are preset from the factory to neutral values which suit
most viewing and listening situations. However, if you wish, you can adjust these
settings to your liking.
Temporary settings ‘DEFAULT VIDEO’
‘DEFAULT AUDIO‘
To only store picture and sound settings until you switch off the TV, press EXIT instead of GO when you accept the settings. The speaker combination chosen in the ‘DEFAULT VIDEO’ submenu is activated automatically when you switch on a video source via the TV. The speaker combination chosen in the ‘DEFAULT AUDIO’ submenu is activated automatically when you switch on an audio source via the TV.
Preset volume, bass, treble or loudness, a connected BeoLab subwoofer and two default loud speaker combinations. The contents of the ‘SOUND’ menu vary according to what you have connected to the TV. See also p. 14 about speaker combinations.
Adjust sound
Adjust brightness, colour and contrast. For information on picture format, see p. 16. Adjustments made to the ‘TINT’ setting only apply to the current source.
Enter and accept settings
Press MENU to bring up ‘TV SETUP’ menu
Enter and accept settings
Press MENU to bring up ‘TV SETUP’ menu
Select ‘SOUND ADJUSTMENT’ menu
Remove the picture from the screen temporarily.
Mute the picture Press LIST repeatedly to display P.MUTE on Beo4 and accept
Adjust picture Select ‘OPTIONS’ to bring up ‘PICTURE’ menu
Select ‘OPTIONS’ to bring up ‘SOUND’ menu
PICTURE
BRIGHTNESS ...............CONTRAST ...............COLOUR ...............TINT ...............SIZE ...............HOR. SIZE ...............VERT. SIZE ...............HOR. POSITION ...............VERT. POSITION ...............GAME MODE
select
SOUND ADJUSTMENT
VOLUME ...............BASS ...............TREBLE ...............SUBWOOFER ...............LOUDNESS ON
DEFAULT VIDEO SPEAKER3
DEFAULT AUDIO SPEAKER2
store
15
NTSC signal only 1080p/i signal only
VGA signal only
Game mode and picture format
1*LIST menu
2*Optimise
3*Variation
In order to display FORMAT on Beo4, you must first add it to the Beo4 list of functions. See your Beo4 guide. The picture format is optimised if you press GO on Beo4. On Beo5 press Optimise. Use or to select other options than the standard option. On Beo5 press Variation.
Select picture format The TV automatically adapts the picture to fill out as much of the screen as possible, when you select a source, but you can select a format yourself.
Adjust picture up or down with arrow buttons if possible
Bring up FORMAT in your Beo4 display*
1
Select format*2
You can minimise delays in signals while playing games or select a picture format to
customise the viewing experience.
Useful hints
Set the TV to minimise delays while playing games.
Activate game mode
You can deactivate game mode at any time. If you switch source or switch the TV to standby, game mode is deactivated automatically.
Deactivate game mode
Select ‘GAME MODE’ menu and select GAME MODE ON
Select ‘OPTIONS’ to bring up ‘PICTURE’ menu Bring up ‘TV SETUP’ menu
Select ‘GAME MODE’ menu and select GAME MODE OFF
Select ‘OPTIONS’ to bring up ‘PICTURE’ menu Bring up ‘TV SETUP’ menu
The picture is adjusted vertically
Zoom For a genuine 16:9 widescreen picture
Wide For panoramic view or 4:3
Standard*3
The bars can be removed and the picture is shown in a 16:9 format
Extended
FORMAT 1 FORMAT 2 FORMAT 3 FORMAT 4
1–4
16
Dai
ly u
se
Sleep Timer and Play Timer
You can set a Sleep Timer which will switch off your TV after a specific period of
time. You can also make your TV switch on and off automatically by setting a
Play Timer in your main room system.
1*LIST menu
Safety
In order to display SLEEP on Beo4, you must first add it to the Beo4 list of functions, if available. For safety reasons, the stand will not turn if the TV is switched on by a Play Timer.
To include the TV in the Play Timer, set the Timer to ‘ON’.*
2
Switch on the Play Timer Select ‘ON’ and accept Select ‘PLAY TIMER’
menu Press MENU to bring up ‘TV SETUP’ menu
Select ‘TIMER ON/OFF’ menu
Set the TV to switch to standby after a specific period of time. You can also access Sleep Timer via the ‘TV SETUP’ menu.
Activate a Sleep Timer Press GO repeatedly to make your selection Bring up SLEEP in your Beo4 display*
1
If you change your mind you can always deactivate the Sleep Timer.
Deactivate a Sleep Timer Bring up SLEEP in your Beo4 display
2*NOTE! To set a Play Timer you must have
another Bang & Olufsen product with a clock function connected to the TV.
Press GO until OFF is displayed
17
You can turn your TV while watching a TV programme.
Turn the television
Press Turn TV
Select STAND Turn TV
Turn the television
You can turn your TV using your remote control if you have a motorised stand.
1*TV positions Position 1 is the far left position and Position 9 is the far right.
Useful hints NOTE! To use the stand function, you have to calibrate the stand first, see p. 35. To preset positions for the TV to turn to, see p. 38.
or
Select position*1
Select position*1
or
LIST 1–9
Stand Turn Position
1…9
18
Inst
alla
tion
and
sett
ing
up
20 Connect and set up an audio system
22 Connect and set up a BeoLink system
23 Your television in a link room
24 Two televisions in the same room
26 Set up your television
28 Expand your setup
30 Set up additional equipment
32 Connection panels
34 First-time setup of your television
36 Loudspeaker setup
38 Additional settings
39 On-screen menus
39 Cleaning
Contents – Installation and setting up 19
Useful hints TV and audio speakers
Choice of Options
Play a CD on your audio system using speakers connected to the TV, or select a TV channel and send the sound to your audio system speakers. If you have a Beo4 remote control, Options for the TV can be 1, 2, or 4 in a main room and 5 or 6 in a link room. Options for the audio system can be 0, 1, 2, 4, 5, 6.
Connect and set up an audio system
To obtain the benefits of an integrated audio/video system, connect a compatible
Bang & Olufsen audio system to the TV using a Master Link cable.
If your TV has been set up in an audio/video system, set it to the correct Option. First, switch the entire system to standby and then stand in front of the TV.
2. Set Option for TV
Connect the sockets marked MASTER LINK on the TV and the audio system using a Master Link cable.
1. Connect the audio system
Set the audio system to the correct Option. First, switch the entire system to standby and stand in front of the audio system.
3. Set Option for audio system
Press Select zone in which TV is placed
Select OPTION? and accept
Select V.OPT Select Option
Hold
and
Press
and
Hold Press
Press Select zone in which audio system is placed
Select OPTION? and accept
Select A.OPT Select Option
Hold
and
Press
and
Hold Press
LIST
…
LIST LIST 0–6
LIST
…
LIST LIST 0–6
Option pgm
Option pgm
MASTER LINKMASTER LINK
20
Inst
alla
tion
and
sett
ing
up
NOTE! Not all Bang & Olufsen audio systems support integration with the TV. For more information, contact your Bang & Olufsen retailer.
Options For information about Option 4, 5 and 6, see pp. 23–24.
Your audio/video system can be placed together in one room or in two rooms with
the TV in one and the audio system with a set of speakers in another.
Select Options This page provides an overview of the Options available when using the Beo4 remote control. To set the correct Options with Beo5, select the zone in which your product is placed, see p. 25.
The TV with or without additional speakers and an audio system with a connected set of speakers are set up in one room. Set the TV to Option 1 and the audio system to Option 1.
The TV and audio system are set up in one room with all speakers connected to the TV. Set the TV to Option 2 and the audio system to Option 0.
The audio system is set up in one room and the TV with or without additional speakers in another. Set the TV to Option 2 and the audio system to Option 2.
Option 0Option 2
Option 1Option 1
Option 2Option 2
21
Useful hints NOTE! HDMI signals cannot be distributed from a main room TV to the link room system.
1*Connected equipment If an audio system is already connected to the MASTER LINK socket
and you wish to connect more equipment, the Master Link cable must be split in two and joined with the cable from the link room using a special junction box. Contact your Bang & Olufsen retailer for assistance.
Connect and set up a BeoLink system
Connect and set up a BeoLink system to see pictures and hear sound in link rooms.
You can, for example, connect the living room TV to another video system or to a
set of speakers in another room.
To distribute video signals to link rooms, it is necessary to connect a non-Bang & Olufsen link tuner to the link room TV.*
1
Connect a link tuner
MASTERLINK
AV2MASTERLINK
RF OUT
Option 6*
22
Main room Link room
Link tuner
Inst
alla
tion
and
sett
ing
up
1*NOTE! If you have a Beo4 and you connect the TV for use in a link room where other link systems are already connected, such as speakers, you must set the TV to Option 5 instead.
Your television in a link room
If you have a BeoLink system, operate all connected systems through the TV in a
link room.
Follow the procedure described here when you connect your TV for use in a link room.
Connect link room TV
For your entire system to function properly, it is essential that the TV in the link room is set to the correct Option before you connect it to the system in the main room. Stand in front of the link room TV.
Set Option for a link room TV
Press Select zone in which TV is placed
Select OPTION? and accept
Select V.OPT Select Option 6*
1
Hold
and
Press
and
Hold Press
Option pgm
LIST
…
LIST LIST 6
23
1 Connect the link room TV to the mains supply.
2 Use your remote control to program the link room TV to the correct Option.
3 Disconnect the link room TV from the mains.
4 Make the necessary connections. 5 Reconnect the link room TV to the mains
supply.
Useful hints
Two televisions in the same room
If you have two TVs in the same room and one remote control for both TVs, it is
essential that the TVs are set to the correct Options for them to function properly.
If you place a second TV in a main room where you already have a Bang & Olufsen TV and commands from your remote control can be received by both TVs, you must change the Option of the secondary TV to prevent simultaneous activation of both TVs. Stand in front of the secondary TV.
Select the correct Option
Select LINK Select source Activate a source simply by pressing the relevant source button. However, if your TV is set to Option 4 and you are using a Beo4, follow the instructions to activate a source. If you wish to dedicate a remote control to your secondary TV, contact your Bang & Olufsen retailer.
Beo4 – operate TV in Option 4
LINK on Beo4 In order to display LINK on Beo4, you must first add it to the Beo4 list of functions. See your Beo4 guide for more information.
Press Select zone in which TV is placed*1
Select OPTION? and accept
Select V.OPT Select Option 4
Hold
and
Press
and
Hold Press
LIST TV
LIST
…
LIST LIST 4
BeoVision 10Option 4
TV
LIST
LINK
TV
Option pgm
24
Inst
alla
tion
and
sett
ing
up
1*NOTE! For information about choice of zone, contact your Bang & Olufsen retailer.
Select zone for the TV you wish to use
Select source Normally, if you have a Beo5, you can activate a source simply by pressing the relevant source button. But if you have two TVs in the same room, you must remember first to select the zone of the TV you wish to use.
Beo5 – operate the TVs … BeoVision 10Zone ‘A’
Zone ‘B’TV
Zone ‘A’TV
BeoVision 10Zone ‘B’
TV
25
Set up your television
Important Ventilation
Follow the guidelines for placement and connection described on this and the
following pages.
Handling We recommend that you place the TV in the packaging while you fasten the hinges for the wall bracket or the bracket for the stand.
Wall bracket and motorised stand Set the maximum angle the TV will turn on the stand. See p. 35. The wall bracket can manually be turned 45˚ left or right depending on your setup. Remember to leave enough space around the TV to allow it to turn and tilt freely.
Placement options The TV can be placed on a motorised stand or mounted on a wall bracket.
To ensure proper ventilation, allow enough space around the screen. Do not cover the fans. At over heating (flashing standby indicator and an on-screen warning), switch the TV to standby, not off, in order for the TV to cool down. You cannot operate the TV during this time.
Due to the heavy weight of the TV, any moving orlifting of the TV should be performed by qualifiedpersonnel – using the proper equipment.
Three protection profiles have been enclosed with the TV. Use these when moving the TV to avoid scratching the frame.
26
Inst
alla
tion
and
sett
ing
up
Run cablesYou can fasten the cables to either side or in the middle, depending on wall bracket or stand placement.
Overview
If you have a motorised stand make sure that there is enough slack in the cables to allow the TV to turn to either side before you fasten the cables with cable strips to make a neat bundle.
Fasten the front cloth cover
NOTE! If the front screen glass should crack or chip, or if it should be damaged in any way, it must be replaced immediately, as it could otherwise cause injury. You can order replacement front screen glass from your Bang & Olufsen retailer.
Locate the connection panel and other important items.
When the TV is placed on a wall bracket or stand you can attach the front cloth cover.Hold the front cover with both hands and attach it at the bottom first. Then carefully attach it to the top and adjust its position before letting go.
During cleaning it is recommended to remove the front cover. Avoid spraying liquid directly on the screen as this may damage the speakers, use a soft cloth instead. See p. 39 also. Carefully remove the front cover by supporting it in the side and at the bottom.
1 Mounting bracket for wall bracket. 2 Mounting bracket for stand. 3 Cover for the connection panel. Here you also
find the mains supply connection. Pull out at the bottom to remove the cover.
4 Depending on your setup, lead the cables through one of the three holes. Remove the part of the cover using a pair of tongs.
27
Expand your setup
Information
Your TV supports a wide range of additional equipment.
‘STANDBY OPTIONS’ Set the set-top box to switch off when you change source or when you switch off the TV. You can also choose that the set-top box should always be switched on or that it should be switched on and off manually by means of the remote control.
Disconnect from the mains While expanding your setup, the TV must be disconnected from the mains.
Disconnect TV from mains Switch off TV
Connect additional equipment To operate non-Bang & Olufsen products with Beo4, attach a Bang & Olufsen IR-transmitter to each product. See also p. 31.
Select settings in the ‘CONNECTIONS’ menu Make the connections
Switch on the TV Always attach covers before you connect the TV to the mains.
Connect TV to mains supply Attach all connection covers Switch on TV
Connect external set-top box To get access to any channels you must connect an external set-top box. Make sure you have a 21-pin cable, an adaptor and other required equipment.
Select settings in the ‘CONNECTIONS’ menuConnect set-top box
28
Inst
alla
tion
and
sett
ing
up
Register additional equipment If not detected automatically by the TV, register the equipment you have connected to the TV. Repeat the procedure for each socket group.
Select ‘OPTIONS’ to bring up ‘CONNECTIONS’ menu
Bring up ‘TV SETUP’ menu
Select sockets in a socket group and register
VGA Y – Pb – Pr
HDMI
Equipment connected via VGA socket (AV3). Equipment connected via Y – Pb – Pr socket (AV2–AV4 and AV6). Equipment connected via an HDMI socket. If you have set the ‘HDMI EXPANDER’ in the ‘CONNECTIONS’ menu to ‘YES’, the ‘C’ option in the ‘AV’ menus is replaced with ‘C1’, ‘C2’, ‘C3’, and ‘C4’. Then the ‘A6’ menu also becomes available.
Follow on-screen instructions
Source options in the ‘AV1–AV4’
and ‘AV6’ menus
Contents of the ‘CONNECTIONS’
menu
The above are only examples of registrations; you can register available equipment to any source option. You may also have to register additional equipment in the Master Link system.
Select ‘STANDBY OPTIONS’ menu
29
NONE V.MEM DVDDVD2DTV2 (V.AUX) DTV V.AUX2 TV PC LINK
Nothing connected Connected set-top box (only AV2-4 and AV6)Connected DVD player or recorder Connected DVD player or recorderEquipment, such as a set-top box Equipment, such as a set-top box Equipment, such as a video game console Equipment, such as a set-top box Connected PC or BeoMaster (only AV3) Connected link tuner (AV2)
AV1–AV6 HDMI EXPANDER
Register connected equipment Enable or disable an HDMI Expander connected to the HDMI C socket
Set up the TV with video sources and loudspeakers.
Loudspeakers Use Bang & Olufsen Power Link speakers. Use the cables enclosed with the speakers. Cables are available from your Bang & Olufsen retailer.
Equipment with HDMI output Equipment with HDMI output such as a set-top box can be connected to any available HDMI socket in the TV, regardless of the particular AV socket group to which you have connected the equipment. To distribute the source to another room you must also connect the equipment to a 21-pin socket or AV3 video input socket on the connection panel. For more information on how to set up connected equipment for use, see p. 32.
Useful hints
Set up additional equipment
Additional video equipment Connect many different types of video equip ment at the same time. Here you can see examples of source names you can select for the equipment in the ‘CONNECTIONS’ menu.
Note: If an HDMI Expander is connected the ‘AV6’ menu is also available.
HDMI CHDMI Expander
AV 1–5
PUC 1–4
PUC 1–4
STB
AV 1–5DVD
AV 2Link TunerPOWER LINK
SUB
POWER LINK
REAR
POWER LINK
FRONT
30
Inst
alla
tion
and
sett
ing
up
Audio system Connect a Bang & Olufsen audio system with a Master Link socket to your TV. Connect it to the Master Link socket on the main connection panel.
Mains cord and plug The supplied plug and mains cord are specially designed for the product. Do not change the plug and if the mains cord is damaged, you must buy a new one from your Bang & Olufsen retailer. Connect the ~ socket on the main connection panel of your TV to the wall outlet. The IR-receiver lights up in red and the TV is in standby mode and ready to be used.
IR-transmitters: To operate non-Bang & Olufsen products with a Bang & Olufsen remote control, attach a Bang & Olufsen IR-transmitter to each of the products. Connect each transmitter to the corresponding socket marked PUC on the main connection panel.
IR typeIn the AV menus you can select how a PUC controlled product is connected. You can choose between ‘PLUG’ (cable) and ‘IR’ (IR Blaster). Only accessible if you have selected an IR socket.
ML
STB
STBPLUG
IR
31
Connection panels
Any equipment you connect to the main connection panel must be registered in
the ‘CONNECTIONS’ menu. See p. 29.
Useful hints
~ – Mains supply Connection to the mains supply.
Connect stereo headphones.
Note: Prolonged listening at high volume levels can cause hearing damage!
AV (1–2 and 4) 21-pin sockets for connection of additional videoequipment, such as a DVD player or set-top box.
AV3 (video, L, R) For audio connection (right and left sound channel respectively) and video signals from an external source.
Headphones To mute speakers press the middle of the volume button. Press the volume up or down to adjust volume in headphones. To restore sound in speakers, press the middle of the volume button.
CAMERA5
32
Mains supply
Inst
alla
tion
and
sett
ing
up
Y – Pb – Pr For video signals from an external source, e.g. HDTV source. You can use the socket in conjunction with an AV socket or a digital audio socket.
SPDIF (1–2) Digital audio input socket, e.g. DVD player. You can use the socket in conjunction with an AV socket.
PUC (1–4) For IR control signals to external equipment connected to an AV socket.
HDMI IN (A–C) For High Definition Multimedia Interface video source or PC. The sources can be registered to any of the AV socket groups. To expand the number of HDMI sockets, connect an HDMI Expander to the HDMI C socket.*
1
VGA (AV3) For connection of a PC to receive analogue graphics.
MASTER LINK For a compatible Bang & Olufsen audio or video system.
POWER LINK (SUB) Use for connection of a Bang & Olufsen subwoofer.
POWER LINK (FRONT – REAR) Use for connection of external loudspeakers in a surround sound setup. See also pp. 36–37.
STAND For connection of a motorised stand.
CAMERA (R, L, video, AV5) For audio connection (right and left sound channel respectively) and video signals from an external source.
1*The ‘AV6’ menu The ‘AV6’ menu becomes available in the ‘CONNECTIONS’ menu when an HDMI Expander is
connected. See p. 30.
33
First-time setup of your television
Connections Select the type of equipment connected to each socket, the sockets used, the product name, and the source name.
Information
This first-time setup procedure is activated when the TV is connected to the mains
and switched on for the first time. If you want to change your setup at a later date,
you can access the same menus and update your settings.
Switch on the TV
Select settings You are led through the following settings only when you switch on the TV for the first time.*
1
It takes the TV approx. 20 seconds to start up and become ready for use.
Switch on
Select setting Accept and go to next menu item
Set the on-screen menu language Calibrate the stand, see p. 35 Set stand positions, see pp. 35 and 38 Register connected equipment, see p. 29
1*NOTE! When you have selected the preferred settings in a menu, you may have to press the green button to continue to the next menu in the first-time setup procedure. Follow on-screen instructions.
TV
MENU LANGUAGE STAND ADJUSTMENTSTAND POSITIONSCONNECTIONS
34
Inst
alla
tion
and
sett
ing
up
Calibrate the speakers Set up the speakers to optimise sound from your listening position.
Calibrate the stand Set the maximum angle the TV will turn – left and right. The motorised movement of the TV will not work until the calibration process has been completed. You can only tilt the TV manually.
First-time setup of loudspeakers applies only to speakers for TV viewing. See also ‘Loudspeaker setup’ on pp. 36–37 and ‘Surround sound’ on p. 14.
Adjust volume, bass, treble and loudness and preset two default speaker combinations. Select a different speaker combination at any time. See pp. 14–15.
At ‘SET LEFTMOST POSITION’ turn left to the point you wish to restrict the movement to
At ‘SET RIGHTMOST POSITION’ turn right to the point you wish to restrict the movement to
Accept
Set preferred preset position for the TV to turn to, when it is switched on and off. See p. 38.
NOTE! You need to calibrate the stand before you can use the motorised movement of the stand.
STAND POSITIONS
SPEAKER TYPE SPEAKER DISTANCE SPEAKER LEVEL
SOUND ADJUSTMENT
STAND ADJUSTMENT
35
Switch on the TV to adjust speaker settings.
Select speaker setup Select ‘OPTIONS’ to bring up ‘SOUND’ menu
Switch on TV and bring up ‘TV SETUP’ menu
Sound during setup During the setup process, a sound is sometimes produced by a speaker. Check if the highlighted speaker matches the name of the speaker making the sound.
Set speaker type Register the type of each speaker in the menu.
Loudspeaker setup
Enter the straight-line distances in metres between your favourite viewing position and the individual speakers.
Set speaker distance
Select speaker and reveal speaker type Select ‘SPEAKER TYPE’ menu
Add Power Link speakers and a BeoLab subwoofer to your TV and you have a
surround sound system.
Select speaker and select distance
Select ‘SPEAKER DISTANCE’ menu
Accept
Accept
Select menu
Information
Set speaker distance
CENTRELEFT
FRONTRIGHT FRONT
RIGHT REAR
LEFT REAR
36
Inst
alla
tion
and
sett
ing
up
Calibrate the sound level A calibration sound is produced alternately in each speaker. Adjust the speakers to match the centre speaker’s sound level. This will ensure an optimal surround sound. .
NOTE! Once you have performed the speaker calibration, you will only need to re-calibrate the speaker sound if you make changes to the setup.
Select ‘AUTOMATIC’ or ‘MANUAL’ in ‘SEQUENCE’
Select ‘SPEAKER LEVEL’ menu Accept
See active sound system See the name of the active sound system for a source or programme on the screen.
Select ‘SOUND SYSTEM’ menu
If ‘MANUAL’ is selected, select speaker and adjust level
Select ‘OPTIONS’ to bring up ‘SOUND’ menu
Bring up ‘TV SETUP’ menu
37
Additional settings
Set a position for when you watch TV, listen to music, and when the TV is switched off. See p. 35 about first-time installation of the stand.
Positions of the TV Select ‘VIDEO‘, ‘AUDIO‘, ‘STANDBY’ or ‘STAND ADJUSTMENT’
Bring up ‘TV SETUP‘ menu and select ‘OPTIONS’ menu
Accept*1
Turn TV as desired
Useful hints
You can make the TV switch off after a specific period of time. It is set to four hours
from the factory. You can also set positions for the TV to turn to.
1*First-time setup During first-time setup, when you have set the TV positions, press the green button to continue first-
time setup.
Set the TV to switch off after a specific period of time without operation. Only in video mode.
Activate auto standby
You can deactivate the auto standby at any time.
Deactivate auto standby
Select ‘OPTIONS’ menu
Bring up ‘TV SETUP‘ menu
Select ‘AUTO STANDBY‘ and then ‘OFF’Bring up ‘TV SETUP‘ menu
Select ‘AUTO STANDBY‘ and make your selection
Select ‘OPTIONS’ menu
Select ‘STAND POSITIONS’ menu
STAND POSITIONS
VIDEO
AUDIO
STANDBY
STAND ADJUSTMENT
select
38
On-screen menus
General settings: Select TV and MENU.
Maintenance Screen
Cabinet and controls
Never alcohol
Regular maintenance, such as cleaning, is the responsibility of the user. Use a mild window cleaning fluid and lightly clean the screen without leaving streaks or traces. Some micro-fibre cloths may harm the optical coating due to their strong abrasive effect. See also p. 27. Wipe dust off the surfaces using a dry, soft cloth. To remove stains or dirt, use a soft, damp cloth and a solution of water and mild detergent, such as washing-up liquid. Never use alcohol or other solvents to clean any parts of the TV.
Cleaning
SLEEP TIMER p. 17 PLAY TIMER
OPTIONS
TIMER p. 17
CONNECTIONS
SOUND
PICTURE
STAND POSITIONS
AUTO STANDBY p. 38BEO4 SETTING p. 6
MENU LANGUAGE
AV1–AV6 p. 29HDMI EXPANDER p. 29
SOUND ADJUSTMENT p. 15SPEAKER TYPE p. 36SPEAKER DISTANCE p. 36SPEAKER LEVEL p. 37SOUND SYSTEM p. 37
BRIGHTNESS p. 15CONTRAST p. 15COLOUR p. 15TINT p. 15SIZE p. 15HOR. SIZE p. 15VERT. SIZE p. 15HOR. POSITION p. 15VERT. POSITION p. 15GAME MODE p. 16
VIDEO p. 38AUDIO p. 38 STANDBY p. 38 STAND ADJUSTMENT p. 38
NAVIGATION BUTTONNO NAVIGATION BUTTON
1. 2. Select settings 3.
39
This product is in conformity with the provisions of the Directives 2004/108/EC and 2006/95/EC.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copy-right protection technology must be authorized by Rovi, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi. Reverse engineering or disassembly is prohibited.
HDMI, the HDMI logo and High-Definition Multi-media Interface are trademarks or registered trade marks of HDMI Licensing LLC.
For the US-market only! NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harm ful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equip ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment
and receiver. – Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected.
– Consult the retailer or an experienced radio/TV technician for help.
For the Canadian market only! This class B digital apparatus meets all require-ments of the Canadian Interference-Causing Equipment Regulations.
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the
double-D symbol are registered trademarks of Dolby Laboratories.
Confidential unpublished works. Copyright 1992–2003 Dolby Laboratories.
All rights reserved.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,487,535; 7,003,467; 7,212,872 & other U.S. and worldwide patents issued & pending.
DTS, DTS Digital Surround, ES, and Neo:6 are registered trademarks and the DTS logos, and
Symbol are trademarks of DTS, Inc. © 1996-2008 DTS, Inc.
All Rights Reserved.
40
Electrical and electronic equipment, parts and batteries marked with this symbol must not be disposed of with normal household wastage; all electrical and electronic equipment, parts and batteries must be collected and disposed of separately. When disposing of electrical and electronic equipment and batteries by use of the collection systems available in your country, you protect the environment, human health and contribute to the prudent and rational use of natural resources. Collecting electrical and electronic equipment, batteries and waste prevents the potential
contamination of nature with the hazardous substances which may be present in electrical and electronic products and equipment.Your Bang & Olufsen retailer will advise you of the correct way of disposal in your country.
If a product is too small to be marked with the symbol, it will appear in the User Guide, on the Guarantee certificate, or on the packaging.
Waste Electrical and Electronic Equipment (WEEE) – Environmental protection
All Bang & Olufsen products comply with applicable environmental legislation throughout the world.
41
Recommended