View
213
Download
0
Category
Preview:
Citation preview
At DANIEL COMPANY we are uniquely equipped to offer our customers
a “turnkey” product, utilizing over 20 years of experience as a manufacturer
of air pollution control systems built from corrosion-resistant materials.
Our wealth of engineering strengths is applied primarily to solving odor
control and fume exhaust problems that exist in the private and municipal
markets. Focus is on building system components made of fiberglass
reinforced plastic products with high structural integrity, durable
corrosion resistance, and increased fire safety. In
addition to striving for the highest level of
excellence in performance, DANIEL COMPANY
maintains premium quality manufacturing
standards along with an ardent commitment
to design innovation.
DANIEL COMPANY serves:
• Wastewater Treatment Plants
• Power Generation Plants
• Military Installations
• University Laboratories
• Pharmaceuticals
• Pulp and Paper Mills
• Printed Circuit Board Industries
• Semi Conductor Industries
• Metal Plating Industries
Product Line
Air Scrubber
Engineering and Design
AIR SCRUBBERS – DANIEL COMPANY provides
three types of air scrubbing systems:
• Wet Packed Towers with chemical recirculation
systems designed for higher hydrogen sulfide removal
efficiency.
• Dry Carbon Absorbers used as stand-alone, primary
scrubbers or as secondary polishers.
• Bioreactor Towers utilized as a lower chemical
consumption odor control scrubber.
All of the scrubber vessels are custom-constructed at
Daniel Company’s state-of-the-art specialty fiberglass
reinforced plastic manufacturing plant. The interior
linings are made of premium grade vinyl-ester corrosion
layers. Each scrubber is provided as a monolithic unit
with all appurtenances attached and/or included. Multi-
stage, skid mounted systems are also provided to
facilitate quick and simple installation. Flanged inlets,
stacks, mist eliminators, access ports, lifting and tie-down
lugs, packing, recirculation pumps, nozzles, PVC piping,
pressure gauges, flow meters, pH/ORP sensors and
analyzers, and chemical metering pumps are but a few
of the specialty components included. A one year
manufacturer’s warranty accompanies Daniel
Company’s scrubber systems.
ENGINEERING AND DESIGN –
DANIEL COMPANY has over 150 years of
combined in-house experience in designing odor
control systems. Our professional engineering staff
is expert at:
• Determining the conditions and needs at the
user’s facility by identifying the sources of fugitive
emissions and performing fence line
measurements along with laboratory analysis of
sample contaminants.
• Engineering complete air scrubber systems that
are most suitable for the application at hand.
• Providing ongoing technical support throughout
critical stages of construction and manufacturing
of air pollution conveyance and scrubber systems.
• Providing experienced startup and training
services to facility managers and plant operators
complemented by comprehensive, user-friendly
operation and maintenance manuals.
Daniel Company’s extensive engineering team has
been involved in the successful design of hundred’s
of air scrubbing systems currently in operation.
Ductwork
Dampers
DUCTWORK – DANIEL COMPANY offers process
air ductwork and liquid conveyance pipe fabricated
from flame retardant and corrosion-resistant fiberglass
reinforced plastic, using contact-molded hand lay-up
and filament wound methods. Applications range from
above grade low pressure ductwork to filament wound
buried pipe designed to H-20 live load calculations.
Round sizes range from 4” to 168” in diameter.
Custom-sized rectangular duct and related fittings may
be manufactured using core materials and composite
stiffeners to achieve required structural integrity.
Fittings include round and rectangular elbows with long
and short radii, transitions, flanges, end caps, tees, wyes,
and laterals. Strict adherence to the accepted ASTM,
RTP-1, NBS PS 15-69 dimensional and quality control
standards guarantee the end user a superior product.
Also, as a licensed mechanical contractor, DANIEL
COMPANY is uniquely equipped to install, balance,
and test the performance of complete exhaust and
supply air systems. Certified technicians are proficient
in training installation crews on the jobsite in FRP field
joining and installing techniques.
DAMPERS –
DANIEL COMPANY
offers precision
engineered FRP
butterfly and multi-blade
dampers utilizing only highly
corrosion-resistant parts. Stainless steel or FRP blade
shafts with seals made up of Viton, Hypalon or EPDM
are incorporated for less leakage. Leakage rates are
tested using AMCA 500-D procedures. Worm gear
operators of the pneumatic, electric or hand operated
types are offered, depending on the application.
Opposed blade and Backdraft Dampers are available in
round and rectangular shapes. A complete line of
Zero-Leakage DanELAST isolation dampers are also
available for greater isolation of process air during
shutdown, and particularly for confined space entry
conditions. Long-life non-metallic bearings and custom
designed bushings require minimal maintenance and
ensure continued free movement of the blade. Zero-
leakage DanELAST isolation dampers require far less
maintenance, are more durable, and outperform
conventional butterfly dampers. Dampers range from
sizes 4” diameter to 120” diameter.
Hoods
Decarbonator
CHEMICAL STORAGE TANKS –
DANIEL COMPANY provides filament-wound
fiberglass reinforced plastic corrosion-resistant
tanks typically used for NaOCl and NaOH
solution storage. All tanks are designed to be
installed either above or below grade, and are
built per RTP-1 and ASTM D 3299 industry-
accepted standards. Access ports and fill/drain
nozzles are standard features included in our tanks.
ADDITIONAL APPLICATIONS –
DANIEL COMPANY also manufactures other
equipment and components used in corrosive
environments typically found at water and
wastewater treatment facilities. These include
Decarbonators, Hoods, Launder Covers,Weirs
and Baffles, Ladders, Platforms, Fan Inlet Boxes,
and a myriad of other customized products
requested by our most valued clients.
FLEXIBLE
CONNECTORS –
DANIEL COMPANY
features heavy-duty flexible connectors featuring
polyester tire cord reinforced EPDM, neoprene,
or Hypalon materials with 316 stainless steel
retaining bands. The flexible connectors are
seamless and constructed of one continuous
piece of elastomer, having an integrally molded
hollow-arched volute permitting contraction and
expansion movements. These are designed for
minimal maintenance and easy removal, and are
ideally suited for isolating vibrations of moving
components such as fans from the duct system.
Heavy duty “U”Type expansion joints with
extruded flanges and mating steel retaining rings
are also provided for piping applications.
Daniel Company – www.danielmechanical.comCorporate Office: 1939 West 11th Street – Suite E – Upland, CA 91786 – (909) 982-1555
Manufacturing Facility: 9972 Rancho Road – Adelanto, CA 92301 – (760) 246-1100
Daniel Company Specializes in the design and manufacture of air pollution controlsystems and is a leader in providing a full range of biological odor control systems formunicipal and industrial odor control.
Daniel is uniquely equipped to supply ourcustomers with complete solutions with over 25years as a manufacturer of systems and ourexpertise in designing and engineeringbiological treatment technology.
Orange County – Huntington Beach California
Biological Odor Treatment Solutions
We are a single sourcemanufacturer for complete systemshaving our own manufacturingfacilities for all FRP components –vessels, ductwork, AMCA certifiedDanELAST dampers andaccessories. We can guarantee thebest system and optimumoperational performance since wecontrol the entire productionprocess for all equipment.
Daniel Company – www.danielmechanical.comCorporate Office: 1939 West 11th Street – Suite E – Upland, CA 91786 – (909) 982-1555
Manufacturing Facility: 9972 Rancho Road – Adelanto, CA 92301 – (760) 246-1100
Leading Technology Solutions
Daniel bio-trickling filters and bio-scrubbers provide cost effective odor control solutionsfor hydrogen sulfide, reduced sulfur compounds and volatile organic compounds (VOCs).Employing naturally occurring microorganisms (bacteria) to treat the odorous airconstituents, the microorganisms consume the odorous contaminants as food for energyand cleanse the air as a result.
The media provides a substrate for the biomass to attach and grow on. The media bed isintermittently irrigated with water while the media bed porosity allows the odorous air toup-flow through the bed and make contact with the microorganisms which consume thecontaminants. The vessel size is calculated by the amount of odorous air flow (CFM) tobe treated and the required empty bed residence time (EBRT – time the microorganismsneed to digest the contaminants) for adequate removal. Generally, the expected removalcan be up to 99.9% of the hydrogen sulfide, up to 95% of odors and more than 70% oforganic sulfur compounds.
Through continuous research and development and working with our customers, Danielhas developed a knowledgebase of technical information that enables us to provide acustom solution to any odor control problem employing a proven approach forsuccessfully solving the problem.
Advantages to our customers are.:
Lower cost due to lower power and chemical consumptionLong media life for maximum service and reduced maintenanceMedia selection based on specific odor component problemsNon-proprietary media and componentsNo dangerous chemical storage for treatment – personnel safetyDanELAST dampers – Life time warrantyZero leak dampers provide personnel safety during maintenance
Daniel Company – www.danielmechanical.comCorporate Office: 1939 West 11th Street – Suite E – Upland, CA 91786 – (909) 982-1555
Manufacturing Facility: 9972 Rancho Road – Adelanto, CA 92301 – (760) 246-1100
System Manufacturing
Total System Design Engineering
Daniel Company has over 150 years ofcombined in-house experience in designingodor control systems. Our staff is fullyequipped to provide all the services required tosolve our customer’s odor problems.:
Field investigation analysis & air samplingOdor contaminant determinationComplete system design engineeringInstallation assistanceStartup and training of operators
Our engineering staff will provide complete 3Dsystems design drawings that facilitateconstruction installation work. Upon systemcommissioning, we provide comprehensive,user-friendly operation and maintenancemanuals.
Daniel Company is a unique odor controlsystems manufacturer being verticallyintegrated and with full capability to produceall the required fiberglass reinforced plastic(FRP) vessels, tanks, ductwork, dampers andaccessories. Our FRP manufacturing facility isthe largest on the US West Coast andproduction is certified for ASME, AMCA,AWWA, NBS, SMACNA standards andmethods.
Daniel Company – www.danielmechanical.comCorporate Office: 1939 West 11th Street – Suite E – Upland, CA 91786 – (909) 982-1555
Manufacturing Facility: 9972 Rancho Road – Adelanto, CA 92301 – (760) 246-1100
Total Odor Control Solutions
Daniel Company is THE Complete Odor Control System Solutions Manufacturer who can provide the most cost effective approach to solving our customers’ problems -
We look forward to working with you on your next project!
Bio-Treatment - 123011
Daniel Company – www.danielmechanical.comCorporate Office: 1939 West 11th Street – Suite E – Upland, CA 91786 – (909) 982-1555
Manufacturing Facility: 9972 Rancho Road – Adelanto, CA 92301 – (760) 246-1100
Daniel Company Specializes in the design and manufacture of air pollution controlsystems and is a leader in providing a full range of odor control systems for municipal andindustrial odor control. Biological treatment systems are known by different names;bioscrubbers, bio-trickling filters and bio-towers, but they all employ the same principal ofbacterial microorganisms that metabolize the odor constituents in the air to be treated.
Daniel biological treatment systems provide cost effective odor control solutions forhydrogen sulfide, reduced sulfur compounds and volatile organic compounds (VOCs).Employing naturally occurring microorganisms (acidithiobacillus thiooxidans bacteria) totreat the odorous air constituents, the microorganisms consume the odorous contaminantsas food for energy and cleanse the air as a result.
The media provides a substrate for the biomass to attach and grow on. The media bed isintermittently irrigated with water while the media bed porosity allows the odorous air toup-flow through the bed and make contact with the microorganisms which consume thecontaminants. The vessel size is calculated by the amount of odorous air flow (CFM) to betreated and the required empty bed residence time (EBRT – time the microorganisms needto digest the contaminants) for adequate removal. Generally, the expected removal can beup to 99.9% of the hydrogen sulfide, up to 95% of odors and more than 70% of organicsulfur compounds.
Biological Odor Treatment Medias
Daniel Company – www.danielmechanical.comCorporate Office: 1939 West 11th Street – Suite E – Upland, CA 91786 – (909) 982-1555
Manufacturing Facility: 9972 Rancho Road – Adelanto, CA 92301 – (760) 246-1100
Leading Technology Solutions
Through continuous research and development with media manufacturers and workingwith our customers, Daniel has developed a knowledgebase of technical informationthat enables us to provide a custom solution to any odor control problem employing aproven approach for successfully solving the problem.
Advantages of Biological Treatment Technology to our customers are.:
Lower cost due to lower power and chemical consumptionLong media life for maximum service and reduced maintenanceMedia selection based on specific odor component problemsNon-proprietary media and componentsNo dangerous chemical storage for treatment – personnel safetyDanELAST dampers – Life time warrantyZero leak dampers provide personnel safety during maintenance
The following is a brief explanation of the different medias we employ in our systems.
Crater MaxThe porous Crater-Max™ media can used in the Bio-Scrubber serves as part of theecosystem for the growth of acidithiobacillus thiooxidans microorganisms. The porousCrater-Max™ media also contains the necessary iron content that in a low pHenvironment will create a chemistry of iron ions to support a colony of acidithiobacillusferroxidans microorganisms. The media is of the type that the surface openings are notthrough-and-through, therefore eliminating any increase in static pressure over time dueto sulfur fouling or compaction of the pore structure. The porous media has a provenreliability record for biological growth with a minimum of 500,000 cubic feet installedover a five year period, based on actual installations in a low pH sulfuric applicationswithout degradation. The natural mined lava rock, inorganic media is selected, crushedand screened using no aggregate larger than 3” in diameter, averaging ¾”-1” indiameter, insuring a uniform surface area of a minimum 10,000 square feet per cubicfoot of media.
Daniel Company – www.danielmechanical.comCorporate Office: 1939 West 11th Street – Suite E – Upland, CA 91786 – (909) 982-1555
Manufacturing Facility: 9972 Rancho Road – Adelanto, CA 92301 – (760) 246-1100
Biotrickling Filter Foam
EDT Filtren is an inert polyurethane foam carrier for microorganisms in bio-tricklingfilter applications for H2S and VOC removal. This is a specially engineered media thatguarantees stability (will not crush or compress over time) and homogenous pore sizedistribution for the very good ecosystem support of the microorganisms.
Important advantages are.: low consistent pressure drop for reduced operating cost,excellent water storage capacity, perfect media for settling microorganisms, good waterand nutrient distribution, chemically inert, adaptable to any treatment vesselconfiguration.
Sheet Polypropylene Media
This rigid polypropylene media ismanufactured in sheets that are cut to fit theconfiguration of the odorous air treatmentvessel. The sheets provide very high surfacearea and porosity for microorganism growthwith tremendous passageways for water andnutrient distribution throughout the depth ofthe media.
Sheet Polypropylene Media
The sheet media is available if 4 different densities each with increasing pore size fromlarge (free volume 92%) to larger (free volume 94%).
Important advantages are.: thermo-polypropylene is not-toxic to the environment, lowpressure drop for reduced operating cost, good water storage capacity, excellentmicroorganism growth media, very good water and nutrient distribution, chemically inert,the media’s rigidity insures no compression or distortion during the life of the media,typical life expectancy is 10 years or more.
Daniel Company has many years experience with various media types and knowswhich will work best for each unique application. We are not married to a particularproprietary media and thus are free to make the best selection depending on thetreatment requirements.
Daniel Company is THE Complete Odor Control System Solutions Manufacturerwho can provide the most cost effective approach to solving our customers’ problems -We look forward to working with you on your next project!
Daniel Company – www.danielmechanical.comCorporate Office: 1939 West 11th Street – Suite E – Upland, CA 91786 – (909) 982-1555
Manufacturing Facility: 9972 Rancho Road – Adelanto, CA 92301 – (760) 246-1100
V 1.5.4 Daniel Mechanical Company February 2006
DDaanniieell MMeecchhaanniiccaall CCoommppaannyy Phone: (909) 982-1555Fax: (909) 982-1855
1939 West 11th Street Ste. E danmech@sbcglobal.netUpland, CA 91786 www.danielmechanical.com
DDaannEELLAASSTT**ZERO-LEAKAGE AIR ISOLATION FRP DAMPER
*Patent Pending
Our Sales Representative..: AMDSolutions, Inc. Matthews, NC 28105 Al Derr 704.996.0222alderr@amdsolutionsinc.com
V 1.5.4 Daniel Mechanical Company February 2006
DDaannEELLAASSTT RROOUUNNDD FFRRPP ZZEERROO--LLEEAAKKAAGGEE AAIIRR IISSOOLLAATTIIOONN DDAAMMPPEERR
DANIEL MECHANICAL COMPANY offers precision-engineered fiberglass reinforced plastic zero-leakage DanELAST isolation dampers utilizing only high corrosion resistant parts for air movement and controls. Zero-leakage DanELAST dampers are fire retardant, corrosion resistant, and UV protected. All components are designed with replaceable parts that are easily disassembled for maintenance. The blade shafts are constructed of custom-milled, solid 316SST metal. Daniel Mechanical Company’s zero-leakage DanELAST damper utilizes a specially formulated elastomer with corrosion resistance equal to and/or superior to EPDM, Hypalon, and even Viton.
No circumferential blade seals are required to achieve a full shutoff of the zero-leakage DanELASTisolation damper. This is largely due to the innovative design and expert hand craftsmanship of each key part. By constructing the unitary FRP blade to exact tolerances and without a commonly used circumferential blade seal, the weakest part of the damper is eliminated, thus improving its reliability. No blade stops are utilized, decreasing the pressure loss across the damper when in the full open position. Each zero-leakage DanELAST damper is factory tested to operating pressures exceeding 30 inches w.g. Leakage rates are tested using AMCA 500-D
procedures, and the certified ratings are authorized by AMCA.
The zero-leakage DanELAST damper blade is operated using a hand-wheel driven worm gear operator. Pneumatic, electric, or chain-wheel type operators are optional. Long life Teflon bearings and extensively tested molded plastic bushings accessible from the exterior of the damper require minimal maintenance and ensure unrestricted movement of the rotating shaft. All metal parts in contact with process air stream are at a minimum 316 stainless steel and may be manufactured of more exotic metals such as Hastelloy-C and Titanium.
Zero-leakage DanELAST dampers enhance safety by providing greater isolation of process air during shutdown of low pressure exhaust system duct lines conveying hazardous air streams. When dealing with confined space entry conditions, use of zero-leakage DanELAST isolation dampers may reduce safety risks caused by contaminant air leaks.
Zero-leakage DanELAST isolation dampers require far less maintenance, are more durable, and outperform conventional butterfly dampers.
Zero-leakage DanELAST dampers range in sizes from 4-inch diameter to 120-inch diameter.
SSTTAANNDDAARRDD CCOONNSSTTRRUUCCTTIIOONN
FRAME—Vinyl ester resin fabricated to ASME/ANSI RTP-1 FLANGE—NBS PS 15-69-3.4.7 ¾” thick, hand lay-up integral to body per ASME RTP-1-2000
Standard Fig. 4-7. BLADE—Vinyl ester resin similar to damper frame. Unitary construction with no circumferential seal or
backstop, having a calculated percent deflection of L/360 STIFFENERS—Same material as frame and integrally molded to bladeSHAFT—316 SST with nuts, bolts, and washers (FRP encapsulated if required) SHAFT SEAL—Externally adjustable compression type with FRP housing and Viton O-ringBEARING—Teflon OPERATOR—Worm gear with hand wheel, chain wheel, pneumatic, or electric actuation GEL COAT—Paraffinated, with ultraviolet inhibitorCOLOR—White unless specified otherwise MAXIMUM TEMPERATURE—200 FMAXIMUM PRESSURE—30” w.g. MAXIMUM LEAKAGE—Zero cubic feet per minute per square-foot of cross sectional areaLUBRICANT—None required
V 1.5.4 Daniel Mechanical Company February 2006
DDaannEELLAASSTT RROOUUNNDD FFRRPP ZZEERROO--LLEEAAKKAAGGEE AAIIRR IISSOOLLAATTIIOONN DDAAMMPPEERR
DDEETTAAIILL DDRRAAWWIINNGG
DDaannEELLAASSTT RROOUUNNDD FFRRPP ZZEERROO--LLEEAAKKAAGGEE AAIIRR IISSOOLLAATTIIOONN DDAAMMPPEERR
DDIIMMEENNSSIIOONNSS SIZE FLANGE
THICKNESSFLANGE
O.D. BOLT
CIRCLEDIA.
BOLTHOLEDIA.
# OF BOLT
HOLES
BLADETHICKNESS
AXLEDIA.
“A” “B” DAMPER WIDTH
4” ¾” 8 3/8” 7” 7/16” 4 3/8” ¾” 5” 6” 6”6” ¾” 10 3/8” 9” 7/16” 8 3/8” ¾” 6” 8” 6”8” ¾” 12 3/8” 11” 7/16” 8 3/8” ¾” 6” 8” 6”
10” ¾” 14 3/8” 13” 7/16” 12 3/8” ¾” 6” 8” 12”12” ¾” 16 3/8” 15” 7/16” 12 3/8” 1” 6” 8” 12”14” ¾” 18 3/8” 17” 7/16” 12 3/8” 1” 6” 8” 12”16” ¾” 20 3/8” 19” 7/16” 16 3/8” 1” 6” 8” 12”18” ¾” 22 3/8” 21” 7/16” 16 3/8” 1 ¼” 6” 8” 12”20” ¾” 24 3/8” 23” 7/16” 20 3/8” 1 ¼” 6” 8” 12”24” ¾” 28 3/8” 27” 7/16” 20 3/8” 1 ¼” 7.5” 8” 12”30” ¾” 34 3/8” 33” 7/16” 28 3/8” 1 ¼” 7.5” 8” 12”36” ¾” 40 3/8” 39” 7/16” 32 ½” 1 ¼” 7.5” 8” 12”42” ¾” 46 3/8” 45” 7/16” 36 ½” 1 7/8” 7.5” 8” 12”48” ¾” 54 3/8” 52” 9/16” 44 ½” 1 7/8” 7.5” 8” 12”54” ¾” 60 3/8” 58” 9/16” 44 ½” 1 7/8” 10” 8” 12”60” ¾” 66 3/8” 64” 9/16” 52 ½” 1 7/8” 10” 8” 12”72” ¾” 79” 76” 9/16” 64 ½” 1 7/8” 12” 12” 18”
“A”
SEALESS PRECISION-SHAPED ELIPTICAL FRP BLADE WITH MOLDED STIFFENERS AS REQUIRED
“B”
EXTERNALLY ACCESSIBLE ADJUSTABLE COMPRESSION SEAL MADE OF FRP WITH VITON O-RING & TEFLON BEARING
FRP STANDOFF PLATE
HANDWHEEL WITH WORM GEAR OPERATOR
ZERO LEAKAGE DAMPER BODYWITH EMBEDDED CORROSION-RESISTANT
DanELASTTM ELASTOMER SEALING SEAT
FLANGE DIMENSIONS & BOLT HOLEPATTERN PER NBS PS 15-69
TABLE II
FRP FLANGE INTEGRALTO BODY PER RTP1 STANDARD
NOTES:
1. ALL KEY PARTS ARE DETACHABLE AND EASILY REPLACED WITH SPARE PARTS. 2. DAMPER SHALL BE FULLY OPERATIONAL AT TEMPERATURES UP TO 200º F. 3. DAMPER HAS A LEAKAGE RATING OF ZERO CFM @ 30” W.C. 4. ALL METAL PARTS IN CONTACT WITH PROCESS AIR STREAM ARE 316 SST. MORE EXOTIC METALS SUCH AS HASTELLOY-C
AND TITANIUM ARE OPTIONAL.
LEAK PROOFENCAPSULATING FRP HUB
WITH TEFLON BEARING
TOP VIEW
PATENT PENDING
316 SST CUSTOM MILLED CENTEREDSOLID SHAFT WITH 316 SST HARDWARE
V 1.5.4 Daniel Mechanical Company February 2006
Daniel Mechanical Company certifies that the Model 303 dampers shown herein are licensed to bear the AMCA Seal. The ratings shown are based ontests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certified RatingsProgram. The AMCA Certified Ratings Seal applies to air performance and air leakage ratings. Test method is per AMCA Standard 500-D-98 Figures 5.3, 5.4 Alternate-6.3, 5.5, & 5.6, 6.5. Data are based on a seating torque of chart listed in-lbsapplied to hold the damper in the closed position. Air leakage is based on operation between 50 F - 104 F.
SSUUGGGGEESSTTEEDD SSPPEECCIIFFIICCAATTIIOONNSS FFOORR RROOUUNNDD FFRRPP AAIIRR CCOONNTTRROOLL DDAAMMPPEERRSS
Operator shall be sized according to required operating torque. Operator shall be coated with corrosion resistant epoxy. All metal parts exposed to the air stream shall be 316 SST. All zero-leakage dampers located at elevations exceeding 6’-6” above finished floor shall, in addition to the hand wheel, be equipped with chain wheel sprockets and appropriately sized chain lengths, as manufactured by:
Dampers are installed as shown on plans and per specifications. Damper frame shall be of one-piece construction with a resin rich interior corrosion barrier having a minimum thickness of 100 mils. A structural wall shall consist of alternate layers of chopped strand mat and woven roving to conform to ASME/ANSI RTP-1 and NBS PS 15-69. The overall glass and resin content shall be 40% and 60% by weight, respectively.
1. Babbitt, or equal The fiberglass flange dimensions shall be per NBS PS 15-69 Table 2 for dimensions and bolthole drilling pattern. The flanges shall have a minimum thickness of 3/4 inch and shall be constructed integral to the cylindrical body of the damper, using the hand lay-up technique per ASME RTP-1-2000 standard Fig 4-7. The distance between the faces of the flanges shall be 6 inches for dampers having a diameter size of 8 inches or less. For all other damper sizes, this distance shall be 12 inches long. The damper blade and stiffeners shall be fabricated using the same resin as the damper frame. The damper blade shall be of unitary construction having no detachable parts or circumferential or wiper blade seals. Damper blade shall be designed to prevent over-rotation without the use of backstops located anywhere in the air stream. 316 SST blade shaft shall be continuous, centered, and custom-milled to fit the operator. Both the damper blade and shaft shall be fully detachable from each other and readily disassembled from the damper body for easy repair or maintenance.
Chain wheel sprockets shall have integral chain guides to prevent “gagging”.
Annular DanELAST corrosion resistant elastomer sealing seat shall be embedded in the damper body to achieve zero leakage.
Exterior surface of damper shall contain UV inhibitor, and be gel coated or painted with color to match existing ducting.
FRP dampers shall be tested for pressure drop and leakage in accordance with AMCA Standard 500-D. AMCA 500-D leakage tests shall be performed by AMCA certified testing facilities. The leakage rate shall be a maximum of 0 C.F.M per square-foot of cross-sectional area at 30-inches w.g. pressure. The test results shall be submitted for review and approval by the Engineer. The zero-leakage damper shall bear the AMCA seal.
Damper shall have an FRP structural stand-off bracket integrally laminated to the exterior of the body for mounting a worm gear operator.
Approved manufacturer of zero-leakage isolation damper shall be:
1. Daniel Mechanical – Model: DanELAST 303Damper shall be provided with a self-lubricated hand-wheel driven worm gear operator, as manufactured by:
2. Or equal
1. Dynatorque, or equal
CCEERRTTIIFFIIEEDD RRAATTIINNGGSS AAUUTTHHOORRIIZZEEDD BBYY AAMMCCAA
Blade Fixed Open Damper Diameter
Torqueinch lbs.
LeakageClass P (in. wg) CFM
4” 66 1A - -12” 891 1A 0.11 1,98324” 486 1A 0.04 6,58536” 360 1A 0.03 14,07248” 464 1A - -54” 630 1A - -60” 866 1A - -72” 360 1A - -
V 1.2 Daniel Company May 2009
DANIEL COMPANY1939 West 11th Street, Ste. E Upland, CA 91786
Phone: (909) 982-1555 Fax: (909) 982-1855
danmech@sbcglobal.netwww.danielmechanical.com
HEAVY DUTYFLEXIBLE CONNECTOR/EXPANSION JOINT
DanFLEXDanFLEX
Our Sales Representative..: AMDSolutions, Inc. Matthews, NC 28105 Al Derr 704.996.0222alderr@amdsolutionsinc.com
V 1.2 Daniel Company May 2009
DanFLEX OUTSTANDING FEATURES AND BENEFITS
DanFLEX STANDARD DESIGN AND CONSTRUCTION
FLEXIBLE SLEEVE — Single volute elastomer impregnated fabric or tire-cordELASTOMER MATERIAL — Neoprene, EPDM, or HypalonDUROMETER — 60 to 70 shoreELASTOMER PRESSURE RATING — 5 psiFLANGE — NBS PS 15-69-3.4.7BAND — 316 stainless steel (SST) with screw seal fastenersMAXIMUM TEMPERATURE RATING — 225ºFEXPANSION AND CONTRACTION — Up to a total of 4 inchesOPTIONAL ACCESSORIES — 316 SST control rod assemblies; custom flange bolt-hole patterns and ratings
Simpler and Easier to ReplaceThe elastomer portion of the DanFLEX fl exible connector is an off-the-shelf commodity item. All parts of DanFLEX are pre-engineered, made to standard sizes, and are interchangeable. As a result, replacement lead time is reduced. Furthermore, in the event that the mating equipment is modifi ed and requires a different bolt-hole pattern, the fl ange can easily be replaced without having to change out the entire fl exible connector.
Withstands Extreme Torsional ForcesDanFLEX fl exible connector is designed to absorb extreme and sudden torsional forces without wrinkling and (eventually) cracking of the molded elastomer volute. As an intended fail-safe feature, if excessive twisting forces are applied to the fl ex connector, the fl anges will slip inside the tubular elastomer sleeve instead of tearing it.
Facilitates Accurate InstallationDanFLEX has an adjustable overall length, facilitating a more accurate fi t and fi nish when installing in parent duct/pipe spools which have fi nite length measurements. This is easily achieved by extending the length of either of the FRP fl anged stubs located at each end of the fl exible connector.
Longer Warranty PeriodDaniel Company’s DanFLEX fl exible connector comes with double the warranty period offered by other manufacturers.
Made of High Quality ConstructionDanFLEX is constructed of vulcanized layers of polyester tire-cord fabric reinforcement, sanwiched between a 60 to 70 durometer elastomeric inner liner and exterior cover. Tire-cord fabric is layered at an optimal bias angle with Resorcinol Formaldehyde Latex for superior rubber-to-fabric bonding. The elastomer is built as one continuous piece with an integrally molded, hollow-arched volute. 316 stainless steel retainer bands are used with adjustable screw seal type fasteners.DanFLEX is suitable for use in H2S-laden, corrosive environments, and is resistant to ultra violet rays.
Features Superior FlexibilityDanFLEX fl exible connectors provide superior absorption of lateral, torsional, angular, and axial movement experienced in rigid ducting/piping systems due to thermal expansion and contraction, installation misalignment, and vibration.
Eliminates High Stress PointsThe weakest point of a traditional fl exible connector design is located annularly – where the back of the integrally molded elastomer fl ange meets the tubular section. DanFLEX relieves this high stress area by overlapping the tubular elastomer onto the hubs of the FRP fl anges.
Infi nite Bolt Hole Alignment CapabilityDanFLEX fl exible connector is designed to allow for infi nite adjustment capability to accommodate any degree of axial misalignment of bolt holes.
V 1.2 Daniel Company May 2009
SIZE(I.D.)
FLANGETHICKNESS
(MIN.)
FLANGEO.D.
BOLTCIRCLE
DIA.
BOLT HOLEDIA.
# OF BOLT HOLES
FLANGED FLEX CONNECTOR
LENGTH (NOM.)
4” ¾” 8 3/8” 7” 7/16” 4 12”6” ¾” 10 3/8” 9” 7/16” 8 12”8” ¾” 12 3/8” 11” 7/16” 8 12”10” ¾” 14 3/8” 13” 7/16” 12 12”12” ¾” 16 3/8” 15” 7/16” 12 12”14” ¾” 18 3/8” 17” 7/16” 12 12”16” ¾” 20 3/8” 19” 7/16” 16 12”18” ¾” 22 3/8” 21” 7/16” 16 12”20” ¾” 24 3/8” 23” 7/16” 20 12”24” ¾” 28 3/8” 27” 7/16” 20 12”30” ¾” 34 3/8” 33” 7/16” 28 12”36” ¾” 40 3/8” 39” 7/16” 32 18”42” ¾” 46 3/8” 45” 7/16” 36 18”48” ¾” 54 3/8” 52” 9/16” 44 18”54” ¾” 60 3/8” 58” 9/16” 44 18”60” ¾” 66 3/8” 64” 9/16” 52 18”72” ¾” 79” 76” 9/16” 64 18”
DanFLEX ROUND FLEXIBLE CONNECTOR DETAIL DRAWING
DanFLEX ROUND FLEXIBLE CONNECTOR DIMENSIONS
DETAIL C
TWO NUTS,ONE WASHERON EACH ENDOF ROD
TYP. OF 4
316 SST BAND1/2" WIDEWITH CLAMP
3.
2.
OPTIONAL.CONTROL RODS AND RELATED ACCESSORIES ARE DUCTWORK.TABLE II 3/4" THICK OR TO MATCH MATING FRP
NOTES:
ALL CONTROL RODS, NUTS, BOLTS & WASHERS ARE 1.MADE OF 316 SST.FLANGE BOLT-HOLE PATTERNS ARE PER NBS PS 15-69
3/16" THICKSINGLE ARCHELASTOMER
D
DUCT/PIPEFRP MATING
TYP. OF 3ALL-THREAD ROD
3/8"
TWO WASHERSNUT,
3/8" BOLT,
FRP MATINGDUCT/PIPE
C
DanFLEX MODEL 101 FLEXIBLE CONNECTORWITH CONTROL RODS
1/2" THICKFRP PLATE TYP. OF 3
GASKET
FRP STUB FLANGE3/4" MIN. THICKNESS
DETAIL D FRP MATINGDUCT/PIPE FLANGE
V 1.2 Daniel Company May 2009
DanFLEX SUGGESTED SPECIFICATIONS FOR ROUND FLEXIBLE CONNECTORS
DANIEL COMPANYFiberglass Air Pollution Control Systems
Corporate Offi ce1939 West 11th Street, Ste E • Upland, CA 91786
Ph: (909) 982-1555 • Fax: (909) 982-1855
Manufacturing Facility9972 Rancho Road • Adelanto, CA 92301Ph: (760) 246-1100 • Fax: (760) 246-1161
Website: www.danielmechanical.comEmail: Danmech@sbcglobal.net
Flexible connectors shall be provided wherever indi-cated. To maintain overall system responsibility by a singular source, all fl exible connections shall be sup-plied by the MANUFACTURER of the FRP duct/pipe. Acceptable fl exible connector is DanFLEX Model 101 as manufactured by Daniel Company, or equal.
Flexible connectors are intended to be used in rigid duct/pipe systems for lateral, torsional, angular and axial movement due to expansion, contraction, and vibration. Product may be utilized to compensate for minimal misalignment.
Construction shall be of multiple layers (2 minimum) of vulcanized polyester tire-cord fabric reinforcement, sandwiched between 60 to 70 durometer elastomer inner liner and exterior cover. Use of reprocessed/reclaimed rubber is not acceptable. Tire-cord fabric will be layered at an optimal bias angle with Resorci-nol Formaldehyde Latex for superior rubber-to-fabric bonding.
Seamless construction, built as one continuous piece with integral molded hollow arched volutes, shall permit up to a total of 4” of axial contraction and expansion.
Flexible connectors shall be designed to allow for a minimum of 1” of offset movement in any direction. No wrap, seamed or spliced type fl exible connectors will be allowed
Flanges shall be of FRP construction per NBS PS 15-69-3.4.7. Bolt-hole pattern shall fi t that of mating duct/pipe or equipment.
316 SST retainer bands shall be used with adjustable screw seal type fasteners. All hardware and materials of construction shall be suitable for H2S laden corrosive environment and able to resist UV rays.
Approved manufacturer of fl exible connectors shall be:
1. Daniel Company – DanFLEX Model 101
Our Sales Representative..: AMDSolutions, Inc. Matthews, NC 28105 Al Derr 704.996.0222alderr@amdsolutionsinc.com
DANIEL COMPANY Fiberglass Air Pollution Control Systems
(Rev. 1) REFERENCE LIST
Biological Odor Control Systems: The following is a partial list of BioTrickling Filter odor control systems manufactured and system-integrated by Daniel Company with associated references. All of these systems are currently in operation with the exception of the P2-66 project, which should be in operation by Fall 2011. More references are available upon request. 1. Owner City of Los Angeles, CA Project Name La Cienega and Jefferson Air Treatment Facility (Installed ~ 2009) Contact Tim Haug
Wastewater Conveyance Construction Division Bureau of Engineering – Department of Public Works Phone: (213) 485-4906
System Description a. 20,000 CFM air flow rate b. Inlet H2S Loading: 150 ppm
2. Owner City of Los Angeles, CA Project Name North Central Outfall Sewer Air Treatment Facility (Installed ~
2009) Contact Tim Haug
Wastewater Conveyance Construction Division Bureau of Engineering – Department of Public Works Phone: (213) 485-4906
System Description c. 10,000 CFM air flow rate d. Inlet H2S Loading: 150 ppm
3. Owner City of Los Angeles, CA Project Name Hyperion Treatment Plant Study (Installed ~ 2009) Contact Cyrous Gilani
Environmental Engineering Division City of Los Angeles, CA Phone: (310) 648-6124
System Description System A: City of Los Angeles Hyperion Treatment Plant Experimental Biological Scrubber at Battery B
a. Media Type – Zander Cube b. Pressure drop is less then 3 inches, even at 2 second retention
time. c. 2 second to 15 seconds retention time. d. 500 CFM air flow rate
System B: City of Los Angeles Hyperion Treatment Plant Experimental Biological Scrubber at Battery B
a. Media Type – Lava Rock
b. Pressure drop is less then 3 inches, even at 2 second retention time. c. 2 second to 15 seconds retention time. d. 500 CFM air flow rate
System C City of Los Angeles Hyperion Treatment Plant Experimental Biological Scrubber at Battery B a. Media Type – Matella SM360 b. Pressure drop is less then 3 inches, even at 2 second retention time. c. 2 seconds to 15 seconds retention time. d. 500 CFM air flow rate
System D City of Los Angeles Hyperion Treatment Plant Experimental Biological
Scrubber at Battery B a. Media Type – Lignite Activated Carbon b. Pressure drop is about 6 inches at 4 second retention time c. 4 seconds to 15 seconds retention time d. 500 CFM air flow rate
4. Owner Orange County Sanitation District Project Name P2-66 – Plant 2 Headworks Replacement 2010 Contact Khalil Kairouz Carollo Engineers Phone: (714) 540-4300
System Description System #1: Headworks System a. 188,300 CFM air flow rate (max.) b. Pressure drop: 6-8 inches water column c. 2 seconds retention time d. Bed depth: 9 feet e. Media material: Juergen Loy’s foam f. Biotower is humidified through a recirculation pump with makeup water
System #2: Trunkline System a. 40,000 CFM air flow rate (max.) b. Pressure drop: 6-8 inches water column c. 2 seconds retention time d. Bed depth: 9 feet e. Media material: Juergen Loy’s foam f. Biotower is humidified through a recirculation pump with makeup water
5. Owner Los Angeles County Sanitation District Project Name Valencia Water Reclamation Plant
(Installed ~ 2002) Contact Robert Morton
Page 2 of 3
Page 3 of 3
Sr. Engineer 24501 S. Figueroa Carson, CA 90745 Phone: (310) 830-2400
System Description a. 12,000 CFM air flow rate b. Average inlet H2S concentration: 20 ppm c. Over 5 years in operation
6. Owner Los Angeles County Sanitation District Project Name Saugus Water Reclamation Plant (Installed ~ 2003) Contact Robert Morton
Sr. Engineer 24501 S. Figueroa Carson, CA 90745 Phone: (310) 830-2400
System Description a. 16,000 CFM air flow rate b. Average inlet H2S concentration: 30 ppm c. Over 5 years in operation
7. Owner Los Angeles County Sanitation District Project Name L.A. County Joint Water Pollution Control Plant (Installed ~ 1995) Contact Robert Morton
Sr. Engineer 24501 S. Figueroa Carson, CA 90745 Phone: (310) 830-2400
System Description Test unit. 1,500 CFM full scale system 8. Owner Delta Diablo Sanitation District Project Description Headworks, Antioch Pump Station, & Pittsburg Pump Station
(Installed ~ 2006) Contact Scott Cowden
CH2M HILL Engineering Corvallis, OR Phone: (541) 758-0235 x3456
System Description 16,000 CFM total air flow rate 9. Owner City of Livermore, CA Project Name Livermore Water Reclamation Plant (Installed ~ 2000) Contact Ralph Olson and Kevin Kepler
Sr. Engineer and Sr. Operation Manager 101 W. Jack London Blvd Livermore, CA 94559 Phone: (925) 960-8100
System Description a. 7,000 CFM air flow rate b. Average inlet H2S concentration: 40 ppm c. Over 9 years in operation
Additional references are available upon request.
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: MDL 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
RICHMONDODOR CONTROL FACILITY
BIOTRICKLING FILTERTOP VIEW - BTF-1DATE: 12/22/09
DWG. NO. BTF-1
SCALE: 1/2" = 1'
4' 0"0°
45°
90°
110°
135°
180°
202.5°
225°
247.5°270°
315°
190°
MH-1
N-1
N-2
N-3
N-4
N-5
MH-2MH-2
L-1
L-2
L-1
L-1 L-2
L-1
L-1
L-2
L-2
L-1
L-1
L-1
NO. QTY. SIZE PROJECTION SERVICE ELEVATION FLANGE
N-1 1 42" x 24" 6"FOUL AIR
INLET
NBS PS 15-69
N-2 1 30" 6"FOUL AIR
OUTLET
NBS PS 15-69
N-3 2 8" 6"SPRAY WATER INLET
ANSI 150 POUND
N-4 1 4" 6" DRAIN OUTLET
ANSI 150 POUND
N-5 6 1/2" 2" DPI TAP NPT FEMALE
MH-1 1 30" 6"TOP
ACCESS PORT
NBS PS 15-69
MH-2 2 24" 6"SIDE
ACCESS PORT
NBS PS 15-69
L-1 8 IIA 4" ANCHOR LUG N/A
L-2 4 PER CALCS
PER CALCS
GUIDE LUG N/A
ELEVATION
1"
3' - 0"
1' - 0"
A: N-5 SHALL BE AT ELEVATIONS OF: 5' - 0", 16' - 3", 19' - 9", 31' - 0", 34' - 6", 36' - 0"
A
38' - 0"
18' - 4"33' - 2"
37' - 10"
18' - 4"33' - 2"
33' - 5"
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: MDL 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
RICHMONDODOR CONTROL FACILITY
BIOTRICKLING FILTERTOP VIEW - BTF-2DATE: 12/22/09
DWG. NO. BTF-2
SCALE: 1/2" = 1'
4' 0"0°
45°
90°
70°
135°
180°
337.5°
225°
297.5°270°
315°
350°
MH-1
N-1
N-2
N-3
N-4
N-5
MH-2
MH-2
L-1
L-2
L-1
L-1L-2
L-1
L-1 L-2
L-2
L-1
L-1
L-1
NO. QTY. SIZE PROJECTION SERVICE ELEVATION FLANGE
N-1 1 42" x 24" 6"FOUL AIR
INLET
NBS PS 15-69
N-2 1 30" 6"FOUL AIR
OUTLET
NBS PS 15-69
N-3 2 8" 6"SPRAY WATER INLET
ANSI 150 POUND
N-4 1 4" 6" DRAIN OUTLET
ANSI 150 POUND
N-5 6 1/2" 2" DPI TAP NPT FEMALE
MH-1 1 30" 6"TOP
ACCESS PORT
NBS PS 15-69
MH-2 2 24" 6"SIDE
ACCESS PORT
NBS PS 15-69
L-1 8 IIA 4" ANCHOR LUG N/A
L-2 4 PER CALCS
PER CALCS
GUIDE LUG N/A
ELEVATION
1"
3' - 0"
1' - 0"
A: N-5 SHALL BE AT ELEVATIONS OF: 5' - 0", 16' - 3", 19' - 9", 31' - 0", 34' - 6", 36' - 0"
A
38' - 0"
18' - 4"33' - 2"
37' - 10"
18' - 4"33' - 2"
33' - 5"
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: MDL 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
2" INTERNAL CPVCSPRAY HEADER
2"
4' 8"
1' 0"
5' 0"
1' 2"
4' 0"
3' 5 7/8"4' 8"
6' 3"7' 2"
1' 10"
RICHMONDODOR CONTROL FACILITY
BIOTRICKLING FILTERBTF-1 FRONT VIEWDATE: 12/22/09
DWG. NO. BTF-1 FRONT
SCALE: 3/16" = 1'
1' 0"
3' 0"4' 6"
5' 6"
10" x 10" BOX BEAMS
4' 0"
1' 2"
5' 2"
ELEVATION VIEW
TYP, SEE TOP VIEWS FOR ACTUAL ORIENTATION
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: MDL 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
RICHMONDODOR CONTROL FACILITY
BIOTRICKLING FILTERFRONT VIEW - BTF-2DATE: 12/22/09
DWG. NO. BTF-2 ELEV
SCALE: 3/16" = 1'
NO. QTY. SIZE PROJECTION SERVICE ELEVATION FLANGE
N-1 1 42" x 24" 6"FOUL AIR
INLET
NBS PS 15-69
N-2 1 30" 6"FOUL AIR
OUTLET
NBS PS 15-69
N-3 2 8" 6"SPRAY WATER INLET
ANSI 150 POUND
N-4 1 4" 6" DRAIN OUTLET
ANSI 150 POUND
N-5 6 1/2" 2" DPI TAP NPT FEMALE
MH-1 1 30" 6"TOP
ACCESS PORT
NBS PS 15-69
MH-2 2 24" 6"SIDE
ACCESS PORT
NBS PS 15-69
L-1 8 IIA 4" ANCHOR LUG N/A
L-2 4 PER CALCS
PER CALCS
GUIDE LUG N/A
1"
3' - 0"
1' - 0"
A: N-5 SHALL BE AT ELEVATIONS OF: 5' - 0", 16' - 3", 19' - 9", 31' - 0", 34' - 6", 36' - 3"
A
38' - 0"
18' - 4"33' - 2"
37' - 10"
18' - 4"33' - 2"
35' - 5"
N-2MH-1
L-2
L-1
L-1
N-4
N-3
N-3
N-5
N-5
N-5
N-5
N-5
MH-2
MH-2
0'-1"0'-0"
1'-0"
0'-0"
3'-0" N-1
N-55'-0"
18'-4"
16'-3"
19'-9"
31'-0"
34'-6"
36'-3"
33'-2"
35'-5"L-2
33'-2"
18'-4"
BTF - 2 FRONT VIEW 3/16" = 1'
BTF - 2 BACK VIEW3/16" = 1'
BTF - 1 IS MIRROR IMAGESEE TOP VIEW FOR ACTUAL ORIENTATIONELEVATIONS ARE THE SAME FOR BTF - 1
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: MDL 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
RICHMONDODOR CONTROL FACILITY
BTF SYSTEMOVERALL VIEWDATE: 12/22/09
DWG. NO. OVERALL
SCALE: 3/4" = 1'
BTF - 1 BTF - 2
WATER PANEL(COVER REMOVEDFOR CLARITY)
WATER PANEL
RECIRC PUMP
SPRAY PIPING
RECIRC TANK
P - TRAP
SAFETY DRAIN
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: BH 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
CITY OF RICHMOND, VASCUM CONTROL UPGRADES
NEW CONCENTRATOR BUILDINGFIRST FLOOR PLANDATE: 09/10/09
DWG. NO. BM1
SCALE: 3/16"=1'-0"
18"Ø OBD
30"Ø DAMPER(TYP)
30"Ø FLEXCON (TYP)
BTF-2
BTF-1CF-1
CF-2
127
127
123
123
116
116
115
114
113
112
113
114
115
103
102126
104
N
FJ
FJ
FJFJ
FJ
FJ
NOTES:1. CONTRACTOR TO VERIFY ALLDIMENSIONS AND TIE-IN CONNECTIONSAND EQUIPMENT CONNECTIONS.2. CONTRACTOR TO VERIFY TYPE OFCONNECTION TO EQUIPMENT.
7' 3"
22.5°
8' 10"
42"ØSLIP ON STYLE FLEXCON
14' 1
0"
6' 2"
18' 1"
6' 10"
3' 6"
4' 4"
30"Ø FLEXCON (TYP)
124
124
6' 7"
FJFJ
203203
1
1
1
1
1
1
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: BH 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
135 BEHIND
125
CITY OF RICHMOND, VASCUM CONTROL UPGRADES
NEW CONCENTRATOR BUILDINGSECTIONDATE: 09/09/09
DWG. NO. BM4
SCALE: 3/16"=1'-0"
BTF-2
CF-2
30"Ø FLEX CON(TYP)
30"Ø DAMPER(TYP)
OCF-2
42"Ø DAMPER
42"Ø SLIP ON FLEX CON
30"Ø BYPASSSTACK
2-24"Ø EXHAUSTSTACKS
FJ
FJ
FJ
FJFJ
FJ
FJ
FJ
FJ
125
124
122
123127
121
111
110
109
129
134
120
108
119
128
117
131
130
105A
102112114115116
NOTES:1. CONTRACTOR TO VERIFY ALLDIMENSIONS AND TIE-IN CONNECTIONSAND EQUIPMENT CONNECTIONS.2. CONTRACTOR TO VERIFY TYPE OFCONNECTION TO EQUIPMENT.
107
30"Ø SLIP ON STYLE FLEXIBLE CONNECTOR (TYP 3 WALL PENETRATIONS)
WALL SLEVE BY GC(NOT SHOWN FOR CLARITY)(TYP ALL WALL PENETRATIONS)
126
137
TO 138 (SEE BM6)
30x30 BACKDRAFT DAMPERWITH TRANSITIONS (SEE DETAIL)
3' 6"
4' 4"
4' 4"
4' 0"
3' 6"
10' 6"
19' 10"
4' 10"
FJ105
17' 1"
7' 6"
21' 6"
28' 3"
3' 8"
9' 3"
38"Ø x 42"ØOBD (SEE DETAIL)
130A
136
FJFJ
FJ
FJ
FJFJ
203
202
201
204
1
1
1
1
1
1
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: BH 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
CITY OF RICHMOND, VASCUM CONTROL UPGRADES
NEW CONCENTRATOR BUILDINGSECTIONDATE: 09/09/09
DWG. NO. BM6
SCALE: 3/16"=1'-0"
OCF-1 OCF-2 OCF-3
30"Ø DAMPER(TYP)
42"Ø DAMPER
42"Ø x 30"ØCON RED
(TYP)
30"Ø FLEX CON(TYP)
NOTES:1. CONTRACTOR TO VERIFY ALLDIMENSIONS AND TIE-IN CONNECTIONSAND EQUIPMENT CONNECTIONS.2. CONTRACTOR TO VERIFY TYPE OFCONNECTION TO EQUIPMENT.
110
FJ
109
FJ
110
109
FJ
118
119
120
FJ
134
106 106
132 133
FJ
FJ
119
120
FJFJ
102
103104 114113
105
134
42"Ø BLINDFLANGE
3' 6"18' 1"
14' 10"
16' 6"
10' 0"10' 0" 7' 3"9' 11"
7' 11"
TO 7SEE BH1 FORCONTINUATION
18x18 OBDSEE DETAIL
126
137 138
FJ
TO 139SEE SECTION VIEW ABOVE
FOR CONTINUATION
18"Ø SLIP ONSTYLE FLEX
CONNECTOR
6' 3"
8' 6"
70' 0"
139 138
BELOW GRADE RUN1" = 20'
BG1
18"Ø SLIP ON STYLE FLEX CONNECTOR OUTSIDE
CONCRETE WALL
FJ
FJ
201
202
1 1
1 1 1
1
1 1
1
1
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: MSD 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
40' 6"
40' 6"
9' 8"
7' 7"
2' 0"
1
1
1
1
3
CITY OF RICHMOND, VASCUM CONTROL UPGRADES
NEW CONCENTRATOR BUILDINGFIRST AND SECOND FLOORSDATE: 09/18/09
DWG. NO. BH1
SCALE: 1/4"=1'-0"
38"Ø x 26"ØCON RED
26"Ø 90°LR ELL
26"Ø x 24"ØCON RED
24"Ø x 22"ØCON RED
22"Ø x 18"ØCON RED
18"Ø x 14"ØCON RED
30"Ø x 28"ØCON RED
28"Ø x 26"ØCON RED
26"Ø x 24"ØCON RED
24"Ø x 20"ØCON RED
20"Ø x 14"ØCON RED
14"Ø END CAP
14"Ø END CAP
18" x 10"REGISTER
(TYP)
18" x 12"REGISTER
(TYP)
TO 38"Ø x 42"Ø OBDSEE DWG. BM6FOR CONTINUATION
FJ
1
FJ FJ FJ2 4
FJ
5
FJ
6
FJFJFJFJFJFJ
7
8
910111213
1"DRAWING IS ONLY TO SCALE ONLYIF THIS LINE MEASURES 1" LONG
SIZE: B
FILE DIR: 1588
DRAWN BY: MSD 9972 RANCHO ROADADELANTO, CA 92301TEL: (760) 246-1100FAX: (760) 246-1161
DANIEL COMPANYFIBERGLASS AIR POLUTION CONTROL SYSTEMS
8' 11"
4' 9"
40' 6"
27' 2" 9' 2"
1' 3"
1
1
1
1
CITY OF RICHMOND, VASCUM CONTROL UPGRADES
NEW CONCENTRATOR BUILDINGFIRST AND SECOND FLOORSDATE: 09/18/09
DWG. NO. BH2
SCALE: 1/4"=1'-0"
30"Ø 90°LR ELL
32"Ø x 30"CON RED
34"Ø x 32"ØCON RED
36"Ø x 34"ØCON RED
30"Ø x 28"ØCON RED
28"Ø x 26"ØCON RED
26"Ø x 24"ØCON RED
24"Ø x 20"ØCON RED
20"Ø x 14"ØCON RED
14"Ø END CAP
18" x 12"REGISTER(TYP)
18" x 12"REGISTER(TYP)
36"Ø x 16ØCON RED
16"Ø END CAPFJ
FJ FJ
FJ
FJFJFJ
FJFJFJFJ
14
FJ
FJ FJ
FJ
1516
17
18192021
22
23
24 2526 27 28 29
30"Ø 90°LR ELL
Recommended