View
0
Download
0
Category
Preview:
Citation preview
To see the complete KADO range go to www.reece.com.au/bathrooms
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 5
ASPECT
SPECIFICATIONSRecommended Use Domestic, Hotel and Commercial
Vanity Top Material White Matte Solid Surface (15mm)
Vanity Unit Material MDF MR E0 (Medium Density Fibreboard, Moisture Resistant, Rated Emission Level E0)
Vanity Colour Variations
(see page 2)
Textured Woodgrain:
Riven: Light grain texture.
Nuance: Deep wide grain texture.
Ravine: Deep wide grain texture.
Natural Woodgrain:
Matte smooth.
Gloss Silk:
Sheen gloss smooth.
Polyurethane:
White Gloss or Matte, Matte Milton Moon Grey, Black Matte. Smooth.
Interior Finish Graphite Grey on Polyurethane units / Exposed Interior on Woodgrain units.
Tap Hole Availability 0 or 1 Tap Hole
Waste Flexi-Dinger Pop-Up Waste Kit (supplied)
Fixing Bolted/Screwed to the wall by a licensed tradesperson- Fixings not included.
Drawers/Inclusions ADP Premium Soft-Close Drawers with LED.
*Optional Extra Grass Sensomatic Auto-Drawer Open (no handle required)
Concealed internal drawer.
Leatherette Tray Organiser and Tissue Box.
White Solid Surface Handle standard.
Ensembles Shaving Cabinets (900mm, 1200mm, 1500mm).
Mobile unit on castors.
Tall Boy wall hung.
Wall Cabinets (1400mm, 1800mm).
STANDARD SIZES 900mm
Offset
1200mm
Offset
1500mm
Offset
Width (mm) 900 1200 1500
Depth (mm) 500 500 500
Height (mm) 515 515 515
Number of Drawers 2 3 3
page 1 of 7
POLYURETHANE FINISH (Available on Plus Models only)
Smooth
Nuance: Deep wide grain texture
Ravine: Deep wide grain texture
WOODMATT FINISH Smooth matte
NATURAL FINISH Smooth matte
GLOSS SILK OR NATURAL FINISH Smooth glossy / matte
SILK FINISH Smooth & glossy
BlackBlackened Linewood
Raw Birch Ply Gloss White
Smoke ElmChalky Teak
Matte White
Antico Oak
Distressed Wood
Classic Oak
Notaio Walnut
Prime Oak
Cherry RiftwoodTawny Linewood
Polar White
Matte Milton Moon Grey
Domain Espresso Ligna
Riven: Light grain texture
Cherished WoodConcrete Formwood Rural OakSeasoned Oak Sublime TeakWashed Knotty Ash
Parchment
Matte Black
Chalk: Subtle linea texture
Delana Oak Aged Walnut
ASPECT
Gesso Lini Rocco Lini Truffle Lini
page 2 of 7
VANITY UNIT:
150
62268
700
811
005
890
900300
51
005
500216
350
622
110
68 90
621
497
005
500216
350
622
110
68 90
621
497
005
1190
120030051
482.5
150
622
316.5
622101
150
675.5
541
150
550 150
62268
365 900
621
005
1490
1500600
51
005
500216
350
622
110
68 90
621
497
150
550 150
62268
365 900
621
005
1490
1500600
51
005
500216
350
622
110
68 90
621
497
ASPECT
Dimensions are nominal measurements only.
page 3 of 7
SENSOMATIC DRAWER OPTION:(OPTIONAL EXTRA)
100
PLUMBING AREA450mm (W)350mm (H)FROM TOP.
PLUMBING AREA350mm (W)350mm (H)FROM TOP.
POWER AREA200mm (W)200mm (H)FROM BASE.
POWER AREA120mm (W)200mm (H)FROM BASE.
POWER AREA120mm (W)200mm (H)FROM BASE.
Recommended240V Power PointLocation.
Recommended240V Power PointLocation.
Recommended240V Power PointLocation.
OPEN SHELF
OPEN SHELF
100
100
70
660
100
100 100
PLUMBING AREA350mm (W)350mm (H)FROM TOP.
100 100
600 250
566 450 484
350
70
350
Power point240v (not supplied)
Power packand plug (supplied)
Hot and Cold water outlet (if applicable)
ASPECT
Dimensions are nominal measurements only.
page 4 of 7
SHAVING CABINET:
MOBILE: TALL BOY:
873
900
413 482
70
004
130
03263
8
004
150
873
1200
004
374 374 445
70130
03263
8
004
150
873
1500
004
521 451 521
70 70130
03263
8
004
150
285
400
120 120
405
285
407
400
036051
68
289
400
81
405
216252
511
289
407
402
350
28
USB-charge 10-light LED sensor light included.
ASPECT
Dimensions are nominal measurements only.
page 5 of 7
1400
400
1400
134
150
1800
600
1800
200
216
WALL CABINETS:
1400MM:
1800MM:
ASPECT
Dimensions are nominal measurements only.
page 6 of 7
INSTALLATION INSTRUCTIONS
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
INSTALLATION INSTRUCTIONS
Prior to installation it is important to unpack & inspect your products to ensure no damage has occurred in transit and that the product IS CORRECT. If damage has occurred, or a visible defect exists, do not proceed with installation and contact supplier IMMEDIATELY.
NO claims for damages / defects will be recognized after installation
1. Check that wall is level (fig 1 and 2) and plumb both vertically and horizontally. If your wall is out of plumb, or is not flat, you will need to pack your vanity so as not to follow the wall. Your vanity must be level, otherwise it will twist and your doors and drawers will be out of alignment.
2. Mark base and back of vanity for drilling to allow for plumbing pipes.
3. Drill holes for pipes with appropriate size hole saw.
4. Position vanity over pipes in correct position. It may be an idea to use a level support / noggin to assist in levelling a wall hung unit and help identify any un-plumb surfaces which may require packing prior to fixing the unit to the wall.
5. Check with spirit level that the vanity unit is completely level. (fig 3 and 4)
6. Fix vanity to wall through back of vanity ensuring the correct screw/dynabolt size is used by the installer to suit the installation situation.
Where studs cannot be located, it is recommended to use toggle bolts or appropriate hollow-wall fixings. Allow enough fixing points, evenly spaced at the top AND bottom of the back panel, to sufficiently hold the particular unit size onto the situation of the installation area. It may be handy to apply some silicone/adhesive to the rear of the unit prior to fixing, this may assist in levelling and fixing the unit to the wall.
7. Adjust doors and drawers if required as there may have been some movement during transportation and installation.
(refer instructions included in unit)
8. Vanity top is then to be siliconed to the top of the cabinet using non Acidic silicone. Apply an unbroken bead of silicone on
all four edges of the top of the vanity and at the back where the top meets the wall. Ensure to seal any visible gaps between
the cabinet and the top with an unbroken bead of silicone.
9. All edges where vanity top and cabinet meet wall and floor are to be sealed with silicone. Gap filler sealant can be used in place of silicone where unit meets tiled surfaces. All areas need to be sealed to prevent water penetration. Materials used for construction of this unit are water resistant NOT water proof. Care must be taken to dry any spillage or leakage of water which may gain access to cabinet. It is recommended that vanities are installed over 300mm from any wet areas such as baths, spas and showers.
10. Where a separate basin is to be fitted it is essential that the basin is fully sealed to the cabinet and top to prevent any water penetration.
11. Waste is not to be over tightened to avoid stress on basin or top. (recommendation for waste to be HAND tight only)
Fig.1 Fig.2 Fig.3 Fig.4
CLEANING RECOMMENDATIONSThis bathroom product should not be cleaned with abrasive materials eg. steel wool/scourers. Do not use any corrosive or abrasive cleaning agents containing acids or scouring agents. To maintain finish on your top, use only a soft cloth or weak solution of non-abrasive detergent. To restore accidental scratches, marks, etc. rub gently with car cutting compound, car polish or household brass/silver cleaner. Bleaches can discolour products and therefore should not be used. Damage caused by any improper treatment or excessive heat is not covered by the product warranty - refer to Warranty Conditions.
ASPECT
page 7 of 7
Recommended