ANSYS ACT guide - simutechgroup.com · 1 © 2015 ANSYS, Inc. May 29, 2018 ANSYS Confidential ANSYS...

ANSYS ACT guide

Most interesting ACT to complete Workbench’s solutions

Bolt and weld

• Bolt Toolkit• Weld Strength

Codes assessment

• ASME Local Strain Assessment• Pressure Vessels Automatic Paths Creation• ASME Pipe Check• Beam End Release• Wind Load• Spreadsheet Based Load Case Combination• Stress Envelop• Linearized Stresses

Fatigue

• Weld Fatigue• Fatigue Scanning• Fatigue Crossland

Miscellaneous Simulations

• Convection• Acoustics• Hydrostatic Fluid exposure • Exposure of MAPDL Offshore features

General preprocessing

• Analysis Settings Importer• Multi Step Parametric• LoadsBodies/Instances Converter• Mesh Settings

General postprocessing

• Modal Mass• Report Generator• Extended Probe

Bolt and weld

Bolt Toolkit 1200 $

DESCRIPTION

The Bolt Toolkit app simplifies and speeds up the creation and post processing of bolts. Features includes:

• Pretension on groups of existing bolts (CAD bolts).• Creation of groups of simplified bolts (NVH-bolts)

with pretension• Creation of groups of advanced bolts (brick mesh)

with contacts, thread interaction and pretension• Post processing of the bolt types including

Eurocode 3 and VDI 2230

TargetEnergy, construction, Automotive, Consumer Products

Weld Strength

DESCRIPTION

Post processing tool to evaluate weld strength according to Eurocode 3 for fillet and butt welds. All types of FE-models can be used; shell/solid, contact/multi-body, with or without weld geometry

The Weld Strength app can create weld stresses and forces for one or all load steps (maximum over time)

The app can calculate minimum required weld section thickness based on one or all load steps.

1200 $

TargetEnergy, construction, Automotive

Codes assessment

ASME Local Strain Assessment FREE

DESCRIPTION

Perform local strain assessments according to ASMESection VIII division 2 part-5 for pressure vessels bycalculating the local strain limit and a usage factor

The calculation will display the Local Strain Limit results asa contour plot and also give the parameter values

The ACT does not calculate results for shellThis limitation was put there on purpose as the ASME localstrain assessments meant to be used on a well refinedsolid mesh in order to capture the true 3D behavior of themodel

TargetPressure vassels, energy, construction

Pressure Vessels Automatic Paths Creation

DESCRIPTION

Automate the creation of paths & linearized stress results to meet pressure vessels standards

TargetPressure vassels, energy, construction

ASME Pipe Check FREE

TargetPipeline, subsea manifolds, Offshore, energy, construction

DESCRIPTION

Check stress against established industry codes, such as ASME B31.8 Gas Transmission & Distribution Piping Systems

Beam End Release

Target

DESCRIPTION

Expose the end release feature for beam elements and enable advanced graphicpost-processing for beam results

The pre-processing focuses on the end release definition which is available with theelement BEAM 44.

Wind Load

DESCRIPTION

This extension expose the capability of apply wind loading on beam/shell/solid structures per API 4F guideline

Applicable to different geometry types. Either solid, shell or beam structures can utilize this extension

Wind front faces(windward) detection is programmed

TargetPipeline, subsea manifolds, Offshore, energy, construction

Spreadsheet Based Load Case Combination

DESCRIPTION

This extension expose the capability of doing load case combination based on spreadsheet in ANSYS Mechanical

TargetSubsea manifolds, Offshore, energy, construction

Stress Envelop

DESCRIPTION

This App allows user to create an Envelope of Max/MinStresses over all the time steps (substeps).

User is allowed an option to select any of the six stresscomponents along with Equivalent and Principal Stresses

This app would help user to identify the Max tensile andcompressive stresses in a multi step Static/Transient analysisplot.

TargetSubsea manifolds, Offshore, energy, construction

Linearized Stresses

Target

DESCRIPTION

Create Linearized Stresses results for Static and Transient Structural analyses and export them to MS Excel

Fatigue

Weld Fatigue

DESCRIPTION

Post processing tool based on IIW recommendations toevaluate weld fatigue according to Nominal, Hot-Spotand Effective Notch method

The Weld Fatigue app can create results for life,damage, safety factor and stress range along all theweld sections in the model

The cumulative damage for multiple load cases can becalculated.

2200 $

Fatigue Scanning

DESCRIPTION

Post processing tool to evaluate maximum stress or strain range from a selected range of solution steps. Results are saved in a csv file for external fatigue analysis and plotting using “CSV Plot”

With the Fatigue Scanning app you select the geometry ofinterest (typically a number of faces of a body) and let theapp run all possible load case combinations from theselected steps.

The result is the highest stress or strain range from theselected range in the time history

Fatigue Crossland

DESCRIPTION

Fatigue post-processing tool based on the Crossland criterion for Static and Transient simulations

The computation of the Crossland criterion is based on two stress fields:

• The stress fields have to come from the same model (same mesh)

• The stress fields can come from steps of different analyses, or from two different steps of the same analysis

• The second stress field can be null

5000 $

Miscellaneous Simulations

Convection

Target

DESCRIPTION

Expose convection with pilot node capability in steady-state and transient thermal analyses

The Convection ACT extension permits to define aconvection boundary condition connected to an extranode, its temperature becomes the bulk temperature

This allows to consider the temperature variation of thefluid

Acoustics

DESCRIPTION

Expose 3Dacoustic features in Mechanical withoutthe need for APDL

• Define acoustics properties• Apply acoustic boundary conditions & loads• Postprocess acoustic results• Create customized Results• Ability to connect a third party solver in a

standard Workbench process

TargetConstruction, Automotive, Consumer Products

Hydrostatic Fluid exposure

DESCRIPTION

ACT Hydrostatic Fluid extension is a customization made with ACT to integrate ANSYS hydrostatic fluid element capabilities in Mechanical

• 2D & 3D analyses • Create hydrostatic elements and assign fluid material

model Apply boundary conditions & loads: temperature, pressure, mass flow rate

• Plot hydrostatic results: pressure, volume, mass, mass flow

TargetEnergy, construction

Exposure of MAPDL Offshore features

TargetOffshore

DESCRIPTION

ACT Offshore extension is a customization made with ACT tointegrate MAPDL offshore capabilities in Mechanical

Ability to input the basic environment through OCTYPE,BASIC alongwith the ability to adjust and graphically view the mean water leveland sea bed level from the global origin

Ability to input ocean current both as a simple and tabular form ofinput as handled under OCTYPE, CURR commands at any load step

Ability to control the flooding and the input of local variation of dragand inertia coefficients based on Z level, Component based ashandled under OCZONE, ZLOC/COMP commands

General preprocessing

Analysis Settings Importer

TargetAll

DESCRIPTION

Allows the user to use a .csv file to import analysis time stepping

Step,End Time,Time Stepping,Define By,Initial Step/Time,Min Step/Time,Max Step/Time

1,3600,On,SubSteps,1,1,10

2,7200,On,SubSteps,1,1,10

3,10800,On,SubSteps,1,1,10

4,14400,On,SubSteps,1,1,10

5,18000,On,SubSteps,1,1,10

6,21600,On,SubSteps,1,1,10

7,25200,On,SubSteps,1,1,10

8,28800,On,SubSteps,1,1,10

9,32400,On,SubSteps,1,1,10

10,36000,On,SubSteps,1,1,10

11,39600,On,SubSteps,1,1,10

12,43200,On,SubSteps,1,1,10

13,46800,On,SubSteps,1,1,10

14,50400,On,SubSteps,1,1,10

15,54000,On,SubSteps,1,1,10

16,57600,On,SubSteps,1,1,10

17,61200,On,SubSteps,1,1,10

18,64800,On,SubSteps,1,1,10

19,68400,On,SubSteps,1,1,10

20,72000,On,SubSteps,1,1,10

Multi Step Parametric Loads

TargetAll

DESCRIPTION

To make parametric a structural load in a multistepanalysis, including transient ones. The loads taken intoconsideration are: force, pressure, moment anddisplacement

Bodies/Instances Converter

TargetAll repetitive bodies

DESCRIPTION

Simplify repetitive multi-body adjustments by easily defining group and layer instances of similar yet independent solid bodies (e.g., bolts, screws, washers, ...)

You only need to modify one to change all same bodies

Mesh Settings

TargetAll

DESCRIPTION

Mesh utility tool to export/import all global meshsettings in Mechanical meshing for re-use indifferent Workbench projects

General postprocessing

Modal Mass

TargetAll

DESCRIPTION

Allow users to easily view a modal analysis’ effectivemass data without searching through the Solver Outputfile

Report Generator

TargetAll

DESCRIPTION

Create Word report direct from a Mechanical model

The Word template can be modified by the userCustomer tailored versions can be made to includedadditional Mechanical features, section headingsand text objects etc.

1200 $

Extended Probe

DESCRIPTION

A simple app to measure deformed nodal positions, distances and angles

The extension consists of a single button, which will beloaded along with Mechanical GUI when model is opened

This button displays three different behaviors, based on the number of nodes selected when it is clicked

TargetAll

ANSYS ACT guide - simutechgroup.com · 1 © 2015 ANSYS, Inc. May 29, 2018 ANSYS Confidential ANSYS...

Documents

Caea Ansys Ls-dyna Customization Act

ANSYS 17.2 Capabilities - mesco.com.pl · ANSYS ANSYS ANSYS ANSYS ANSYSl ANSYS ANSYS AIM Mechanical Mechanical Mechanical Pro DesignSpace Autodyn LS-DYNA EnterprisePremium = Fully

ANSYS KURULUMU - IbrahimCayiroglu.Com · ANSYS KURULUMU . Inc. 14.0 Product Installation "Windows x64" Browse... Help ANSYS Realize Your ... ANSYS Offshore ANsys AQWA ANSYS Additional

Ansys 10.0 Distributed Ansys Guide

Customization of ANSYS Mechanical: ACT - fluidcodes.com · 1 © 2014 ANSYS, Inc. June 20, 2014 ANSYS Confidential Customization of ANSYS Mechanical: ACT

ANSYS 19.2 Capabilities...1 = ANSYS nCode DesignLife Products 2 = ANSYS Fluent 3 = ANSYS DesignXplorer 4 = ANSYS SpaceClaim 5 = ANSYS Customization Suite (ACS) 6 = ANSYS HPC, ANSYS

ANSYS 18 Capabilities Chart...ANSYS ANSYS ANSYS ANSYS ANSYS ANSYS ANSYS AIM Mechanical Mechanical Mechanical Pro DesignSpace Autodyn LS-DYNA EnterprisePremium l= Fully Supported p=

ANSYS 15.0 Capabilities Brochure - CADFEM · Floquet excitations ... Explicit STR™ ANSYS Autodyn® ANSYS LS-DYNA® ANSYS Fluent® ANSYS CFX® ANSYS CFD-Flo™ ANSYS Polyﬂ ow®

Additive Manufacturing, Topology Optimization and ANSYS ... · • R17 ANSYS Topology Optimization is a free ACT Extension that can be used with any workbench based ANSYS Mechanical

EXCELLENCE IN ENGINEERING SIMULATION - Ansys · EXCELLENCE IN ENGINEERING SIMULATION ... Knowledge Manager, ANSYS Explicit STR, ANSYS Fatigue, ANSYS Fluent, ANSYS Full-Wave SPICE,

ANSYS 19 Capabilities - Mallett Technology, Inc.1 = ANSYS nCode DesignLife Products 2 = ANSYS Fluent 3 = ANSYS DesignXplorer 4 = ANSYS SpaceClaim 5 = ANSYS Customization Suite (ACS)

Ansys contact Ansys contact Ansys contact

ANSYS 2019 R1 Capabilities - inas.ro · 1 = ANSYS nCode DesignLife Products 2 = ANSYS Fluent 3 = ANSYS DesignXplorer 4 = ANSYS SpaceClaim 5 = ANSYS Customization Suite (ACS) 6 = ANSYS

ANSYS 17.2 Capabilities - CADFEM · ANSYS ANSYS ANSYS ANSYS ANSYS ANSYS ANSYS AIM Mechanical Mechanical Mechanical Pro DesignSpace Autodyn LS-DYNA EnterprisePremium l= Fully Supported

10673282 Ansys Tips and Ansys Tricks

ANSYS DESIGN MODELER ANSYS ICEM CFD ANSYS CFX …

ANSYS 2019 R1 Capabilities...2 = ANSYS Fluent 3 = ANSYS DesignXplorer 4 = ANSYS SpaceClaim 5 = ANSYS Customization Suite (ACS) 6 = ANSYS HPC, ANSYS HPC Pack or ANSYS HPC Workgroup

ANSYS ACT Developers Guide

HP Z Workstations For ANSYS · hp z workstations for ansys ... for ansys mechanical, ansys fluent and ... workstation recommendations for gpu usage with ansys

Ansys contactvAnsys contact Ansys contact