Actuators & Valves PIstonPIston SurfaceSurface AreaArea F = P x A Force Where: F = Force in Lbs....

View
216
Download
0
Category

Documents

Tags:

actuators valves t
inches torque
torque output
old slide
square inches
operating pressure
racks pistons
area of piston

Preview:

Citation preview

Actuators & Valves

PIston

Surface

Area

F = P x A

Force

Where:F = Force in Lbs.P = Operating Pressure in lbs. per square inchA = Area of Piston in square inches

OperatingPressure

So, by using two pistons...

Why 2 Racks & Pistons?Why 2 Racks & Pistons?Force is Doubled

Actuators & Valves

If Force is Doubled…If Force is Doubled…Torque Output

Is alsoDoubled!!!

Torque OutputIs also

Doubled!!!

Actuators & Valves

So, it wasout with the old…

Actuators & Valves

And…In with the New!!!

Actuators & Valves

T = F x M.A.Where:T = Torque in Lb.In.F = Force in Lbs.M.A. = Moment Arm in inches

TorqueTorque

Actuators & Valves PIstonPIston SurfaceSurface AreaArea F = P x A Force Where: F = Force in Lbs....

Documents

Thrust Restraint CA-NV Section AWWA Annual Fall …Bearing Thrust Block Bearing Area (ft2) = Safety Factor • Thrust Force (lbs) Bearing Capacity of Undisturbed Soil (lbs/ft2) Undisturbed

Main Advantages - MELTRIC · PART PF PFQ Inlet 15 lbs 9 lbs Receptacle 25 lbs 12 lbs Angled Handle 15 lbs 12 lbs Straight Handle 10 lbs 10 lbs Junction Box 45 lbs 45 lbs Cap 3 lbs

Work Lesson 7.5. Work Definition The product of The force exerted on an object The distance the object is moved by the force When a force of 50 lbs

D-Series High Reliability Circular Connectors · integraMate® D-Series Circular Connectors ... Connector Retention Force 20.0 lbs. min. EIA-364, TP 90 Contact Retention Force 5.0

MC 12 - Drilltal · Feed force Fuerza de empuje 6.000 daN / 13,488 lbs Retract force Fuerza de tiro 6.000 daN / 13,488 lbs Rotary head Cabeza de rotación R1300 R2400 Gears Velocidades

SILVERADO BY THE NUMBERS - chevrolet.com · 14100 lbs 15000 lbs 13700 lbs 20000 lbs 5TH WHEEL/ GOOSENECK TOWING 14400 lbs 15400 lbs 14200 lbs 17500 lbs 13700 lbs 23100 lbs SILVERADO

FA4TM ALIGNING FORCE: 50ft/lbs (33Nm) = 4 T (40 kN) …petracarbon.com.sg/wp-content/uploads/2014/09/FA4TM-Datasheet.pdf · 1 x FA4TM Tool 1 x 50ft/lbs Torque Wrench ... - NEEDLE

Measurement of Work, Power and Energy. Definitions Force = mass x acceleration Work = force x distance –units - kpm, kgm, kcal, J, ft-lbs Power = work

USER INSTRUCTION MANUAL DBI-SALA · Maximum arresting force must not exceed 4 kN (900 lbs) for Class E4 energy absorbing lanyards or 6 kN (1,300 lbs) for Class E6 energy absorbing

CRANES 6% %4#0'5€¦ · (otm = overturning moment) 12 80.0 200000 200000 45 51.7 95100 142650 maximum otm = 15,916,642 ft. lbs. corresponding axial force = 551,950 lbs. maximum axial

00 Ranch 8 V1 01.14€¦ · 2015 142,400 lbs. 4,315 lbs. (5th Leaf) 2016 118,300 lbs. 3,585 lbs. (6th Leaf) 2017 130,020 lbs. 3,940 lbs. (7th Leaf) 2018 232,760 lbs ... Sequoia National

Gas Pressure Pressure = Force/Area Eg: lbs/in2, kg/m2, g/cm2 Force applied to a reduced area will INCREASE Pressure Increased Force applied to same Area

SUMMARY LEVEL RESULTS Total Body Composition · 2020. 9. 15. · Mass (lbs) Fat Tissue (lbs) Lean Tissue (lbs) Bone Mineral Content (BMC) #### 13.5% 191.22 lbs 24.65 lbs 157.85 lbs

1998KAB - imgix...Pleated Shades -20 lbs. 8 lbs. 25 lbs. 10 lbs. 50 lbs. 2 lbs. 2 lbs. 75 lbs. 35 lbs. 5 lbs. Mode Approx. Overall Length Overall Width Approx. Overall Hei ht Interior

STANDARD CAB 22 19,500/25,500 lbs. 12,294-12,875 lbs. 7,275 lbs. 13,660 lbs. 7,275 lbs. 14,550 lbs. 5.571 Tapered/Multi-Leaf 8,440/14,550 lbs. 7.20 in.3 316,800 lb.-in

Operator Manual Manuel Utilisateur Manual del Usuariotuotteet.ramirent.fi/sites/tuotteet.ramirent/files...The maximum allowable manual force is limited to 200 N (45 lbs.) of force

High Force and Long Strokes - HYSON · High Force and Long Strokes • High force in short heights with contact forces to 15,400 lbs. • Stroke lengths to 225 mm • Dynamic lubrication

Certa-Lok vs. Bulldog - CertainTeed vs. Bulldog ... Pipe Size DR Maximum Allowable Pull Force Straight Alignment (lbs.)3 Load at Failure (lbs.)2

UTAH GEOLOGICAL SURVEY a division of Plate 1 · lbm lbm lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs lbs es lbs lbs lbs lbs/QTaf QTaf QTaf QTaf QTaf QTaf QTaf QTaf QTaf QTaf QTaf

Power = Pressure * Pipe Size Area. Pneumatics Pushing Force Force = Surface Area * Pounds Per Square Inch =PiR 2 60 lbs/inch 2 = 3.141 2 inch 2