View
44
Download
2
Category
Tags:
Preview:
DESCRIPTION
ds
Citation preview
SOLID-STATE MEMORY CAMCORDER
PMW-EX3
SERVICE MANUAL1st Edition (Revised 2)
PMW-EX3
! WARNINGThis manual is intended for qualified service personnel only.To reduce the risk of electric shock, fire or injury, do not perform any servicing other than thatcontained in the operating instructions unless you are qualified to do so. Refer all servicing toqualified service personnel.
! WARNUNGDie Anleitung ist nur fr qualifiziertes Fachpersonal bestimmt.Alle Wartungsarbeiten drfen nur von qualifiziertem Fachpersonal ausgefhrt werden. Um dieGefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind beiWartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegebenWartungsarbeiten drfen nur von Personen ausgefhrt werden, die eine spezielle Befhigungdazu besitzen.
! AVERTISSEMENTCe manual est destin uniquement aux personnes comptentes en charge de lentretien. Afinde rduire les risques de dcharge lectrique, dincendie ou de blessure neffectuer que lesrparations indiques dans le mode demploi moins dtre qualifi pour en effectuer dautres.Pour toute rparation faire appel une personne comptente uniquement.
PMW-EX3
Vorsicht!
Explosionsgefahr bei unsachgemem Austauschder Batterie.
Ersatz nur durch denselben oder einen vomHersteller empfohlenen hnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben desHerstellers.
ATTENTION
Il y a danger dexplosion sil y a remplacementincorrect de la batterie.
Remplacer uniquement avec une batterie du mmetype ou dun type quivalent recommand par le
constructeur.Mettre au rebut les batteries usages conformment
aux instructions du fabricant.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent typerecommended by the manufacturer.Dispose of used batteries according to themanufacturers instructions.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtighndtering.
Udskiftning m kun ske med batteriaf samme fabrikat og type.
Levr det brugte batteri tilbage til leverandren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.Brukt batteri returneresapparatleverandren.
VARNING
Explosionsfara vid felaktigt batteribyte.Anvnd samma batterityp eller en likvrdig typsom rekommenderas av apparattillverkaren.
Kassera anvnt batteri enligt gllandefreskrifter.
VAROITUS
Paristo voi rjht jos se on virheellisestiasennettu.
Vaihda paristo ainoastaan laitevalmistajansuosittelemaan tyyppiin.
Hvit kytetty paristo valmistajan ohjeidenmukaisesti.
1 (P)
1PMW-EX3
Table of Contents
2-2-12. SWC-49 Board .................................................... 2-142-2-13. Inside Panel Assembly ........................................ 2-152-2-14. CN-3050 Board ................................................... 2-162-2-15. Connector Rear Assembly ................................... 2-172-2-16. ASW-66 Board, SW-1412 Board ........................ 2-182-2-17. SW-1410 Board ................................................... 2-192-2-18. HN-344 Board ..................................................... 2-202-2-19. HN-343 Board, SWC-48 Board .......................... 2-212-2-20. SW-1411 Board ................................................... 2-232-2-21. Outside Panel Sub Assembly .............................. 2-232-2-22. SW-1389 Board ................................................... 2-242-2-23. Battery Case Assembly ....................................... 2-252-2-24. EX-DD Assembly ............................................... 2-262-2-25. CN-3023 Board ................................................... 2-282-2-26. RE-260 Board ...................................................... 2-292-2-27. EC-63 Board ........................................................ 2-302-2-28. PS-747 Board ...................................................... 2-312-2-29. TX-129 Board ..................................................... 2-322-2-30. Outside Connector Assembly .............................. 2-352-2-31. DPR-289A Board ................................................ 2-362-2-32. Lens Mount Block ............................................... 2-372-2-33. Prism Block Unit ................................................. 2-372-2-34. SE-923 Board ...................................................... 2-382-2-35. AU-318 Board ..................................................... 2-392-2-36. IR-42 Board ......................................................... 2-402-2-37. Replacing the Parts in the Lens Grip ................... 2-41
2-3. Attaching the EMI-Prevention Componentsfor UC Model ................................................................ 2-42
2-3-1. Inside Panel ......................................................... 2-422-3-2. Outside Panel ....................................................... 2-432-3-3. Front Frame ......................................................... 2-442-3-4. Handle ................................................................. 2-452-3-5. Flexible Flat Cable .............................................. 2-472-3-6. Harness (HN337-CN3050) .................................. 2-482-3-7. Main Frame ......................................................... 2-49
2-4. Attaching the EMI-Prevention Componentsfor CE7, CN, E Model .................................................. 2-50
2-4-1. Outside Panel ....................................................... 2-502-4-2. Front Frame ......................................................... 2-512-4-3. Flexible Flat Cable .............................................. 2-522-4-4. Main Frame ......................................................... 2-53
Manual Structure
Purpose of this manual ................................................................. 4Related manuals ........................................................................... 4
1. Service Overview
1-1. External Connectors ........................................................ 1-11-1-1. Signal Inputs and Outputs ..................................... 1-1
1-2. Location of the Printed Wiring Boards ........................... 1-41-3. Circuit Description .......................................................... 1-51-4. Service Tools/Measuring Equipment List .................... 1-11
1-4-1. Service Tools ....................................................... 1-111-4-2. Measuring Equipment ......................................... 1-11
1-5. Firmware Upgrade ........................................................ 1-121-6. Recommended Replacement Parts ............................... 1-131-7. Note on Service ............................................................. 1-14
1-7-1. Requirements on Replacement ofBoards or Parts .................................................... 1-14
1-7-2. Note on Replacement of Parts on the Board ....... 1-141-7-3. Description of Number Seal on the Prism ........... 1-141-7-4. Memory Backup Battery ..................................... 1-141-7-5. Unleaded Solder .................................................. 1-14
1-8. Connector Location Diagram on Board ........................ 1-151-9. Replacing the Flexible Card Wires ............................... 1-161-10. Replacing the Coaxial Cable with Connector
(Fine Pitch Coaxial Cable) ............................................ 1-161-11. List of Error Numbers on the LCD Display ................. 1-18
2. Replacement of Main Parts
2-1. Outline of Replacement Procedures ............................... 2-12-2. Replacement Procedures ................................................. 2-2
2-2-1. Lithium Battery ..................................................... 2-22-2-2. Bottom Panel ......................................................... 2-22-2-3. Pad Sub Assembly, Pad Cover .............................. 2-32-2-4. LCD Assembly, CT-251 Board ............................. 2-42-2-5. Handle Top Cover Assembly ................................ 2-52-2-6. KSW-54 Board, Control Switch Block ................. 2-62-2-7. IF-1069 Board, LED-469 Board ........................... 2-72-2-8. AXM-36 Board, HN-349 Board ............................ 2-82-2-9. Handle Assembly .................................................. 2-92-2-10. Microphone Assembly ........................................ 2-112-2-11. Microphone Unit, MA-164 Board,
RM-214 Board ..................................................... 2-13
2 PMW-EX3
3. SERVICE Menu
3-1. SERVICE Menu List ...................................................... 3-13-2. SERVICE Menu Description .......................................... 3-3
3-2-1. Basic Menu Operations .........................................3-33-2-2. SERVICE Menu Structure .................................... 3-33-2-3. Displaying the SERVICE Menu ........................... 3-3
3-3. SERVICE Menu Description .......................................... 3-33-3-1. MAINTENANCE Menu ....................................... 3-33-3-2. RPN CORRECT Menu .........................................3-73-3-3. INFORMATION Menu .........................................3-8
4. Alignment
4-1. Electrical Alignment ....................................................... 4-1
5. Spare Parts
5-1. Notes on Repair Parts .....................................................5-15-2. Exploded Views .............................................................. 5-25-3. Electrical Parts List ....................................................... 5-245-4. Supplied Accessories .................................................... 5-76
6. Semiconductor Pin Assignments
7. Block Diagrams
Overall ............................................................................ 7-2ASW-66 .......................................................................... 7-3HN-337 ....................................................................... 7-3, 6HP-144 ............................................................................ 7-3LED-469 .........................................................................7-3SW-1412 .........................................................................7-3AU-318 ..................................................................... 7-4, 10AXM-36 ...................................................................... 7-4, 9HN-326 ..................................................................... 7-4, 10HN-328 ........................................................................... 7-4HN-343 ........................................................................... 7-4HN-344 ..................................................................... 7-4, 10HN-349 ....................................................................... 7-4, 9KSW-54 ...................................................................... 7-4, 9MA-164 ........................................................................... 7-4SWC-48 .................................................................... 7-4, 10
BI-202 ............................................................................. 7-5BI-203 ............................................................................. 7-5BI-204 ............................................................................. 7-5DPR-289A .......................................................... 7-5, 6, 7, 8CN-3050 ......................................................................... 7-6EC-63 .............................................................................. 7-6HN-347 ....................................................................... 7-7, 8JK-81 ........................................................................... 7-7, 8JK-84 ........................................................................... 7-7, 8CT-251 ............................................................................ 7-9HN-348 ........................................................................... 7-9IF-1069 ........................................................................... 7-9RM-214 ........................................................................... 7-9SWC-49 .......................................................................... 7-9BP-42 ............................................................................ 7-10HN-345 .........................................................................7-10HN-346 .........................................................................7-10IR-42 .............................................................................7-10SE-923 .......................................................................... 7-10SW-1389 ....................................................................... 7-10SW-1410 ....................................................................... 7-10SW-1411 ....................................................................... 7-10CN-3024 ....................................................................... 7-11TX-129 .......................................................................... 7-11CN-3022 ....................................................................... 7-12DC-146 .........................................................................7-12PS-747 ........................................................................... 7-12RE-260 .......................................................................... 7-12CN-3023 ....................................................................... 7-13RE-261 .......................................................................... 7-13
8. Schematic Diagrams
ASW-66 .......................................................................... 8-2AU-318 ........................................................................... 8-5AXM-36 .......................................................................... 8-8BI-202 ............................................................................. 8-9BI-203 ........................................................................... 8-10BI-204 ........................................................................... 8-11BP-42 ............................................................................ 8-12CN-3022 ....................................................................... 8-12CN-3023 ....................................................................... 8-13CN-3024 ....................................................................... 8-14
3PMW-EX3
CN-3050 ....................................................................... 8-14CT-251 .......................................................................... 8-15DC-146 ......................................................................... 8-15DPR-289A .................................................................... 8-16
SUFFIX: -13 ........................................................ 8-16SUFFIX: -14 .................................................. 8-16 (a)
EC-63 ............................................................................ 8-46HN-328 ......................................................................... 8-46HN-343 ......................................................................... 8-46HN-326 ......................................................................... 8-47HN-337 ......................................................................... 8-47HN-344 ......................................................................... 8-48HN-345 ......................................................................... 8-48HN-346 ......................................................................... 8-48HN-347 ......................................................................... 8-49HN-348 ......................................................................... 8-49HN-349 ......................................................................... 8-49HP-144 .......................................................................... 8-50IF-1069 ......................................................................... 8-50IR-42 ............................................................................. 8-51JK-81 ............................................................................. 8-52JK-84 ............................................................................. 8-53KSW-54 ........................................................................ 8-54LED-469 ....................................................................... 8-55PS-747 ........................................................................... 8-55MA-164 ......................................................................... 8-56RE-260 .......................................................................... 8-57RE-261 .......................................................................... 8-61RM-214 ......................................................................... 8-64SE-923 .......................................................................... 8-64SW-1411 ....................................................................... 8-64SW-1389 ....................................................................... 8-65SW-1410 ....................................................................... 8-65SW-1412 ....................................................................... 8-65SWC-48 ........................................................................ 8-66SWC-49 ........................................................................ 8-68TX-129 .......................................................................... 8-69Frame Wiring ................................................................ 8-77
9. Board Layouts
ASW-66 .......................................................................... 9-2AU-318 ........................................................................... 9-2AXM-36 .......................................................................... 9-3
BI-202 ............................................................................. 9-3BI-203 ............................................................................. 9-3BI-204 ............................................................................. 9-4BP-42 .............................................................................. 9-4CN-3022 ......................................................................... 9-4CN-3023 ......................................................................... 9-4CN-3024 ......................................................................... 9-4CN-3050 ......................................................................... 9-4CT-251 ............................................................................ 9-5DC-146 ........................................................................... 9-5DPR-289A ...................................................................... 9-5
SUFFIX: -13 .......................................................... 9-5SUFFIX: -14 .................................................... 9-5 (a)
EC-63 .............................................................................. 9-7HN-326 ........................................................................... 9-7HN-328 ........................................................................... 9-7HN-337 ........................................................................... 9-8HN-343 ........................................................................... 9-8HN-344 ........................................................................... 9-8HN-345 ........................................................................... 9-8HN-346 ........................................................................... 9-8HN-347 ........................................................................... 9-8HN-348 ........................................................................... 9-8HN-349 ........................................................................... 9-9HP-144 ............................................................................ 9-9IF-1069 ........................................................................... 9-9IR-42 ............................................................................... 9-9JK-81 ............................................................................... 9-9JK-84 ............................................................................... 9-9KSW-54 ........................................................................ 9-10LED-469 ....................................................................... 9-10MA-164 ......................................................................... 9-10PS-747 ........................................................................... 9-10RE-260 .......................................................................... 9-11RE-261 .......................................................................... 9-11RM-214 ......................................................................... 9-12SE-923 .......................................................................... 9-12SW-1389 ....................................................................... 9-12SW-1410 ....................................................................... 9-12SW-1411 ....................................................................... 9-12SW-1412 ....................................................................... 9-12SWC-48 ........................................................................ 9-13SWC-49 ........................................................................ 9-13TX-129 .......................................................................... 9-14
4 PMW-EX3
Manual Structure
Purpose of this manualThe service manual is intended for use by trained system and service engineers, andprovides the information of maintenance and detailed service.
Related manualsThe following manuals are available in this model.If this manual is required, please contact your local Sony Sales Office/ServiceCenter.
..... Operating Instructions (Supplied with the unit)This manual is necessary for application and operation (and installation) of thisunit.
..... Semiconductor Pin Assignments CD-ROMThis Semiconductor Pin Assignments CD-ROM allows you to search forsemiconductors used in Broadcast and Professional equipment.This manual contains a complete list of semiconductors and their ID Nos., andthus should be used together with the CD-ROM.Part number: 9-968-546-06
PMW-EX3 1-1
Section 1Service Overview
1-1. External Connectors
1-1-1. Signal Inputs and Outputs
1 SDI OUT : BNC typeSDI output signal
2 MONITOR OUT : BNC type1.0 V p-p, 75 Z
3 TC IN : BNC type0.5V to 18V, 10 kZ
4 TC OUT : BNC type1.0 V p-p, 75 Z
5 GENLOCK IN : BNC type1.0 V p-p, 75 Z
6 (HEADPHONES) : Stereo mini jackSound monitor, monaural/stereo selectable_20.5 dBu (Reference level 16 Z loaded)
7 AUDIO IN CH-1, CH-2 : XLR (3P, Female)
_____ EXT VIEW _____(0 dBu = 0.775 V rms)
No. Signal I/O Specifications
1 MIC/LINE (G) _ _60 dBu/_50 dBu/_40 dBu/2 MIC/LINE (H) IN +4 dBu, selectable3 MIC/LINE (C) IN High impedance, Balanced
8 S-VIDEO OUT : S-video connector (4P)
_____ EXT VIEW _____
No. Signal I/O Specifications
1 Y/C_GND _ GND
2 Y/C_GND _ GND3 S-Y O S OUT (Y)4 S-C O S OUT (C)
12
3
9 0 !=
76
!\
43
1
5
![2
8
!-
!] !;
SIDE VIEW
FRONT VIEW
REAR VIEW
12
34
1-2 PMW-EX3
9 AUDIO OUT : RCA PIN
_____ EXT VIEW _____
No. Signal I/O Specifications
1 AUDIO CH-1 O _10 dBu
2 AUDIO CH-2 O
0 COMPONENT OUT : Mini D connector (10P)
_____ EXT VIEW _____
No. Signal I/O Specifications
1 Y O COMPONENT (Y)2 Y_GND _ Y GND3 PB O COMPONENT (Pb)4 PBPR_GND _ PBPR GND5 PR O COMPONENT (Pr)6 NC _
7 NC _
8 NC _9 SW_GND _10 SW I
!- HDV : i.LINK connector (IEEE1394, S400) (4P)
_____ EXT VIEW _____
No. Signal I/O Specifications
1 TPB_ I/O Strobe on receive, data ontransmit B (_)
2 TPB+ I/O Strobe on receive, data ontransmit B (+)
3 TPA_ I/O Data on receive, strobe ontransmit A (_)
4 TPA+ I/O Data on receive, strobe ontransmit A (+)
19
210
14
!= (USB) : Mini-B connector (5P)
_____ EXT VIEW _____
No. Signal I/O Specifications
1 VCC _ USB Vcc
2 D _ I/O USB_3 D + I/O USB+
4 ID _ NC5 GND _ Ground
![ DC IN : 2P (DC JACK TYPE 4)
_____ EXT VIEW _____
!] REMOTE : (8P Female)
_____ EXT VIEW _____
No. Signal I/O Specifications
1 TX RCP DATA (X) O SERIAL DATA OUT2 TX RCP DATA (Y) O SERIAL DATA OUT3 RX RCP DATA (X) I SERIAL DATA IN4 RX RCP DATA (Y) I SERIAL DATA IN5 DATA GND _ GND for VIDEO and DATA6 UNREG +12 V O +11 V to 17 V7 UNREG (GND) _ GND for UNREG8 VIDEO (X) O 1.0 V p-p, Zo = 75 Z
CHASSIS GND _ CHASSIS GND
GNDEXT DC
18
2 73 645
1 21 5
PMW-EX3 1-3
1 82 73 6
4 5
1 2 3 4 5
!\ LENS REMOTE : (8P Female)
_____ EXT VIEW _____
No. Signal I/O Specifications
1 COMMON_V O GND2 ZOOM I GND: WIDE 1.66V: STOP
3.33V: TELE
3 COMMON+V O 3.33V4 COMMON I 1.66V5 REC I GND: ON OPEN: OFF
6 RET I GND: ON OPEN: OFF7 SW COMMON O GND
8 FRAME GND _
!; Battery : (5P)
_____ EXT VIEW _____
No. Signal I/O Specifications
1 BATT (+) _ +11 to +17 V dc2 BAT_SCL O
3 BAT_SDA I/O
4 BATT_ID_DATA I
5 BATT (_) _
1-4 PMW-EX3
1-2. Location of the Printed Wiring Boards
1
$[
$=
!]
$;
7
!;
4
8
9
0
!-
!'@\ !.
@]
!,
#\
@= $]
@;#-
@[
6
5
2
@.
@/$/
3
#]
#=
#.
#,
@,
#; #'
$\
@'
!\
$-
#[
@- !=
![
#/
1 ASW-66 board2 AU-318 board3 AXM-36 board4 BI-202 board5 BI-203 board6 BI-204 board7 BP-42 board8 CN-3022 board9 CN-3023 board0 CN-3024 board!- CN-3050board!= CT-251 board
@\ HN-349 board@; HP-144 board@' IF-1069 board@, IF-1072 board@. IR-42 board#/ JK-81 board#- JK-84 board#= KSW-54 board#[ LED-469 board#] MA-164 board#\ PS-747 board#; RE-260 board
![ DC-146 board!] DPR-289A board!\ EC-63 board!; HN-326 board!' HN-328 board!, HN-337 board!. HN-343 board@/ HN-344 board@- HN-345 board@= HN-346 board@[ HN-347 board@] HN-348 board
#' RE-261 board#, RM-214 board#. SE-923 board$/ SW-1389 board$- SW-1410 board$= SW-1411 board$[ SW-1412 board$] SWC-48 board$\ SWC-49 board$; TX-129 board
PMW-EX3 1-5
1-3. Circuit Description
1. CMOS Block System
BI-202/203/204 BoardThe BI-202, BI-203 and BI-204 boards are the rigidflexible boards connecting the CMOS image sensors (IC1)to the DPR-289A board.
The CMOS image sensor receives the three primary colorsof R, G and B that are separated from the incoming lightby the prism. The CMOS image sensor converts theincoming primary color to electric signal. The built-in 12-bit column A/D converters then convert the R, G and Banalog video signals to the digital video signals respective-ly.The electronic shutter, analog gain amplifier and blacklevel clamp functions are also provided in the aboveboards.
The BI-202 board is for the R-channel signal, the BI -203board is for the G-channel signal and the BI -204 board isfor the B-channel signal.The CMOS image sensor receives the sync signal and theserial communication signal from the DPR-289A board.The 12-bit digital video signals that are supplied from theCMOS image sensors pass through the EMI filters (FL1 toFL4) and are input to the DPR-289A board.Various decoupling capacitors and the damping resistorsare also mounted in the above boards.IC3 of the BI-203 board is a temperature sensor that sendsthe temperature data to the CAMERA MICON (camera u-processor: IC314) on the DPR-289A board via I2C bus.
2. Camera Block System
DPR-289A BoardThe DPR-289A board consists of the Camera SignalProcessor IC (IC100) and the CAMERA MICON (camerau-processor: IC314) whereas the Camera Signal ProcessorIC (IC100) performs various processing on the digitalvideo signal supplied from the CMOS image sensor, andthe CAMERA MICON (IC314) performs control of IC100and other various controls such as control of the CMOSimage sensor and of lens. The output digital video (Y/C)signal is sent to the next circuit the video (baseband video)signal processing circuit.
The 12-bit digital video (RGB) signals supplied from theCMOS block (BI-202, BI-203 and BI-204 boards) firstenter the camera signal processor IC (IC100). In thecamera signal processor IC (IC100), average value, peakvalue of the RGB digital video signals that are required for
the following AUTO operations of the camera are detected.The detected signals are sent to the CAMERA MICON(camera u-processor: IC314).. Auto white balance. Auto black balance. Auto focus. Auto iris. Auto knee
The digital video signal from the CMOS image sensorenters first the selector circuit selecting either the digitalvideo signal from the CMOS image sensor or the internalTEST signal. The output video signal from the selectorenters the compensation circuits consisting of the CMOSimager-related compensation circuit and the lens-relatedcompensation circuit. The video signal then receives thewhite balance processing, and the matrix signal and thedetail signal are added to the video signal. The video signalthen receives the pedestal control, knee compensation,gamma correction and white/black clip processing. Thevideo signal finally enters the baseband processing IC(IC400).The pixel number conversion processing from 1920/1080to 1440/1080 or 1280/720 is also performed inside IC100.
The CAMERA MICON (camera u-processor: IC314)performs the overall control over the entire camera systemand is controlled by the camera system controller(IC1600).Peripheral ICs of the CAMERA MICON (camera u-processor: IC314) are FLAH ROM (IC312) and SRAM(IC313). The CAMERA MICON (camera processor:IC314) confirms the iris control and lens setup when theanalog I/F lens is installed.
3. Video Signal System
DPR-289A BoardThe digital video (Y/C) signal output from the camerasignal processor IC (IC100) enters the baseband processingIC (IC400).The baseband processing IC (IC400) performs the overallbaseband processing of video and audio signals with asingle chip IC containing the various scaler functions(supporting the multiple format outputs), various OSDfunctions, PLL function (54 MHz 74 MHz) and CPU.The baseband processing IC (IC400) provides the follow-ing outputs:. HD/SD-SDI (digital): To TX-129 board. HD/SD Component (analog): To JK-81 board. Composite (analog): To JK-84 board. S-Video (analog): To JK-84 board. LCD signal (digital): To IF-1072 board
1-6 PMW-EX3
The input/output signals of the baseband processing IC(IC400) are the following signals:. MPEG encoder/decoder I/F signal (digital): To IC901. Audio I/F signal (digital): To IC804PAM memory (IC700, IC701).Peripheral circuits of the built-in CPU are FLASH ROM(IC603) and SDRAM (IC607).The baseband processing IC (IC400) is controlled by thesystem controller (IC1600). The LCD driver IC, SDI Co-pro, the audio system and the power save control of theoutput systems are controlled by the built-in CPU insideIC400.
4. Media Recording and Playback
DPR-289A boardOutput from the baseband processing IC (IC400) is inputinto the MPEG encoder/decoder (IC901).The MPEG encoder/decoder (IC901) is the single-chipMPEG Codec IC that encodes and decodes both the high-quality HD video signal and audio signal in real-time. Ithas various interfaces with signals such as MPEG video,video input/output, MPEG audio, audio input/output, bitstream input/output, and interface with the host.IC901 output is then input into LSI (IC900) for AVITsignal processing.LSI (IC900) for AVIT signal processing contains the built-in CPU and has interfaces for DDR2 SDRAM memory(IC1000, IC1001), PCI bus, PCI-Express bus, I/O forIC901, and serial communication with system controller(IC1600).IC900 is also connected to the NOR-type Flash ROM(IC1100) to read the CPU program in the IC900 duringinitial startup.LSI (IC900) for AVIT signal processing is controlled bythe system controller (IC1600), in the same way as othermain devices, and provides the following types of func-tions: video/audio stream control, access to the SxSmemory card, mass storage operations when connected toUSB and HDV device controls when connected to i-LINK.
Explanation of peripheral devices
Two memory card slot boards (EC-63) are connected to thedual channel PCI-Express signals coming from IC900through a 0.5 mm pitch, 30-pin fine coaxial cables con-nected to CN1300 and CN1301.Furthermore, dual channel USB host signals output fromUSB host controller (IC1302) are connect to the EC-63board through fine coaxial cables just as with the PCI-Express signals.IC1302 is controlled by PCI bus from IC900.
USB device signal output from USB device controller(IC1101) is connected to output board (JK-81) through theboth-sided flexible board (HN-347) from CN1805 connec-tor, and then it is connected to USB Mini-B connector(CN6) on the JK-81 board.IC1101 is controlled by the dedicated bus from IC900.If there is no USB connection, the power supply forIC1101 drops off.
The i-Link signal output from the i-Link controller(IC1200) passes through the both-sided flexible board(HN-337) from the CN1803 connector. Then, the signal issent from CN3 on HN-337 to the i-Link connector board(CN-3050) through the shielded wire, and connected to the4 Pin i-Link connector (CN3) on the CN-3050 board.IC1200 is controlled by the PCI bus from IC900.
5. Audio system
This overview explains the audio system according to theaudio block diagram shown in Fig. 1.
MA-164 boardThe MA-164 board contains a built-in microphone unit.The MA-164 board amplifies the audio signal with themicrophone bias power supply and head amplifier (Q5,Q7, and Q9, and Q6, Q8, and Q10). It provides the bal-anced output for the audio signal.
AXM-36 boardThe AXM-36 board is a connector board on which XLR(3-pin) connector for external LINE/MIC input and the[LINE/MIC/MIC +48V] input selection switch for twochannels are mounted on this connector board.
KSW-54 boardThis board performs the read and tally controls for theswitch on the handle. The audio signal block relays theaudio signal between the MA-164 board and AXM-36board.
HN-328/HN-343/SWC-48/HN-344 flexible boardThis board relays the audio signal between the KSW-54board and the AU-318 board.
AU-318 board (Audio block)This board controls the analog audio input signal process-ing, as well as microphone +48 V power supply and serialsignal.(RTC is also built on this board, but the explanation hasbeen omitted here.)
PMW-EX3 1-7
MIC/LINE1(XLR)
MIXAMP
MUTE
MIC/LINE 2(XLR)
SPEAKER
MUTE
HP OUT(PHONE
MINI)
MUTE
MUTE AMPAV Monitor
Out1(Line Out1) AV Monitor
Out2(Line Out2)
AMP
AMP
AMP
AMP
+
MONITOR LEVEL
SEL/AMP1
GPIO
+48V /MIC / LINE -2
-24
+48V
-24
+48V
A/D
D/A
I2SAUDIO IFFIL AGC LVL
PGAGAIN
PGAGAIN
INT MIC1with
HEAD AMP+12dB
INT MIC2with
HEAD AMP+12dB
SEL/AMP2
SEL/MIX1
SEL/MIX2
BALAMP
BALAMP
I2C
MONI1-1,2-1,MONI2-2,2-1,BEEP,MUTE
+48V /MIC / LINE -1
PWR or DET MUTE
BALAMP
(GAIN SELCH1)
BALAMP
Linked/Separated
LINE 3/4
Digital AudioOUT 1
CLOCK DIV(1fs,64fs,256fs)
Digital AudioIN 1 or 3
GAIN MAKEOUT 2
Digital AudioIN 2 or 4
CLOCK DIV(1fs,64fs,256fs)
MONI CH2-2MONI CH2-2 BEEP
BEEP(Base band)
AUX IN( L)
AUX IN( R)
DisplayBlock
(Base band)
IC800(2/2)
IC800
IIC toGPIO
DisplayBlock(T-on)I2C
INT/EXT1,INT/EXT2MIC/LINE/+48V-1,MIC/LINE/+48V-2,
COPY1to2, LINK2to1, LINK1to2
A/D
D/A
I2SAUDIO IFFIL AGC LVL
PGAGAIN
PGAGAIN
Q5,Q7,Q9
IC101
IC201
INT/EXT 1
INT/EXT 2
CH1 CH1/CH2 Linked/Separated
IC102
IC202
Q110,Q111
(GAIN SELCH2)
Q210,Q211
Q103 to Q105, Q301,Q302
Q203 to Q205, Q321,Q322
IC105,IC205
IC103,IC104
IC203,IC204
Q6,Q8,Q10
I2C
MONI CH-1MONI CH2-1
CLOCK DIV(1fs,64fs,256fs)
DP_O_CAM_AU_DT12O
(DP_O_CAM_AU_DT34O)
DP_I_CAM_AU_DT34O
DP_I_CAM_AU_DT12O
Q103
Q104IC100,
IC102(1/2)
IC101,IC102(2/2)
Q1
Q2CN2
Q100 to Q102
IC803
IC401 toIC404
IC104, IC105 I2C MPX(DEVICE CONTROL)
MA-164 AU-318
JK-84 DPR
-289
A(2/
2)
HP-144
ASW-66
DPR-289A(1/2)
HN
-337
(1/2)
HN
-347
JK-8
1
LED
-469
HN
-337
(2/2)
KSW
-54
SWC-
48
HN
-344
HN
-328
HN
-343
AXM-36
IC800(1/2)
IC801
IC804C-PLD
Recording signal
Playback signal
Fig. 1. Audio block diagram
. Audio signal from the built-in microphone on the MA-164 board is input to the balanced input amplifier IC101and IC201 of this board. Output of the balanced amplifi-er is connected to the analog switch (IC105, IC205) forswitching between [INT/EXT].
. The DC-DC converter (IC1, Q1) for microphone power+48 V is built-in, and when EXT MIC +48 V is going tobe supplied, the EXT MIC +48 V is supplied by theswitch (Q301, Q302, Q321 and Q322).
. The audio input signals from MIC and LINE are input toa common circuit that receives both of the MIC inputlevel (_8 dBu to _65 dBu) and the LINE input level (+4dBu). The input attenuator is inserted in the circuitswitch (Q103 to Q105, Q203 to Q205) as required. Thisaudio input signal is received by the balanced inputamplifier (IC102, IC202) that performs amplification of0/+12 dB and switching (Q110, Q111, Q210, Q211) inaccordance with the level that is set by INPUT TRIM.After that, the audio signal is connected to the [INT/EXT] switch (IC105, IC205).
. The [INT/EXT] switch (IC105, IC205) performs not onlythe INT/EXT switching but also performs the inputchannel mode selection [CH1/ (CH1/CH2)].
. SEL/AMP (1, 2) is a signal selector and buffer amplifierto perform AGC link.
. Serial controlThe I2C control signal from Display Block (Base band)is converted into GPI, and performs switching such as[INT/EXT], [LINE/MIC/MIC+48], [CH1/ (CH/CH)],and AGC [Linked/Separated] for CH1 and CH2.
DPR-289A board (Audio block)The AU-318 board is comprised of two pieces of theAudio Codec IC and the C-PLD.
. Audio Codec (IC800, IC801)The analog audio signal from the AU-318 board isconnected to IC800 and IC801 that are the Audio Codec(PGA, ADC, DSP, Digital IF, headphones amplifier,speaker amplifier are built on one chip and the parame-ters are set with I2C).The Input TRIM (PGA) functions in the [MANUAL]mode, and AGC functions in the [AUTO] mode tocontrol the audio signal level. The analog signal after
1-8 PMW-EX3
level adjustment is converted to the digital signal withthe ADC.The digital signal receives the audio level controlprocessing from the DSP. After the audio signal receivesthe [Wind Filter] (on/off) processing, the digital signal isoutput for audio recording.Playback output (including EE) is the digital signal thatis connected to Audio Codec where it is converted to theanalog signal with DAC and output to the ASW-66board.Furthermore, the audio signal that is processed for audiomonitoring in the ASW-66 board is connected to theheadphones amplifier and speaker amplifier through themonitor level control from the AUX input of IC800.
. C-PLD (IC804)After the digital signal output signal from the AudioCodec is amplified by +12 dB, it is supplied to theDisplay Block (Base band). C-PLD (IC804) also re-ceives the playback output signal from the DisplayBlock.The playback system selects CH1/CH2 or CH3/CH4,connects EE, and connects TEST TONE from theDisplay Block depending on the data.Furthermore, C-PLD divides the clock signal that issupplied from the Display Block to Audio Codec.
. Serial controlThe I2C control from Display Block (Base band) selectseither IC800 or IC801 for the target with I2C MPX andsets the register of IC800 or IC801.
HN-337 flexible boardIt relays the audio signal from the DPR-289A board to theASW-66 board.
ASW-66 board (Audio block). Analog output from the DPR-289A board Audio Codec
is buffered by IC103 and is output to the A/V connectorafter passing through the audio MUTE control.
. Analog output from DAC on the DPR-289A board re-enters into the AUX input of the DPR-289A boardAUDIO CODEC after passing through the monitorselector/mixer (IC100, IC101, IC102), and becomes themonitor signal.
. Serial controlI2C control signal from Display Block (Base band) isoutput at GPI, and performs the switching betweenMONITOR [CH1/CH2] / [CH1+CH2] / [CH1] / [CH2]for CH1 and CH2 respectively, and at the same timecontrols the BEEP on/off.
JK-84 board (Audio block)This is the connector board. The audio output from theASW-66 board is connected to RCA PIN connector.
HP-144 board (Audio block)The headphones output signal is connected to the head-phones jack of the DPR-289A board.The headphones output is muted by the MUTE (Q1, Q2).
Switch/Volume control/Menu panel (Audiocontroller block)Operation panel functions relating to audio signal are builtinto the following blocks.
ASW-66 board (Audio block)For CH1 and CH2, the switches [INT/EXT] and [AUTO/MANUAL] are connected to PIO of CPU (IC106), and thevolume control [AUDIO LEVEL] is connected to ADC ofCPU (ICl06).
KSW-54 board (Audio block)The switch [LINE/MIC/MIC+48] on the AXM-36 board isconnected to PIO of CPU (IC100) for CH1 and CH2respectively. The switch [MONITOR (AUDIO) +/_] thatis common to CH1 and CH2 is connected to PIO of CPU(IC100).
MENU processing(1) Audio Input
. CH1, CH2 [INPUT TRIM]: _8 dBu to _65 dBu
. CH1, CH2 common [AGC Link]: Linked/Separated
. CH1, CH2 [WIND FILTER]: ON/OFF
. CH1, CH2 common [EXT CH Select]: [CH1] /[CH1/CH2] selection
(2) Audio Output. [MONITOR CH]: [CH1/CH2] / [CH1+CH2] /
[CH1] / [CH2] selection. [Alarm Level]: 0 to 10. [Beep]: ON/OFF. [BARS]: TEST TONE (DPR-289A board Display
Block internal processing)
6. System Control
DPR-289A boardThe 32-bit RISC CPU (ARM) with ARM core is built-in asthe system controller (IC1600).It has the peripheral interface functions of SDRAM, USB,SCI, and I2C. It operates on a 27 MHz clock (X1600).FLASH ROM (IC1603), SDRAM (IC1604), and EE-PROM (IC1703) are mounted as the peripheral ICs.It performs the system control through serial communica-tion with IC314 of the camera block system, IC400 of thevideo signal system, and IC900 of the media recording/playback system.
PMW-EX3 1-9
Main functions of the system controller andperipherals(1) Reading operation switch information
Reading the switch information and the LED controlare performed by I2C bus communication with eachsub-microprocessor.. Handle switch: IC100 on the KSW-54 board. Inside panel front switch: IC601 on the SWC-48
board. Rear panel switch: IC106 on the ASW-66 board. Power supply switch: IC1001 on the RE-261 board
(2) Watch IC (RTC) controlThe watch IC (IC50) is built onto the AU-318 board.The watch IC (IC50) is backed up by a lithium coinbattery, and the current time is read or set via IC601 on theSWC-48 board.
(3) Infrared remote control demodulationThe RM-214 board has an IC (IC1) for infrared remotecontrol signal demodulation, and it receives the commandcodes via IC100 on the KSW-54 board.
(4) Info-Battery communicationThe Info-Battery of SM bus specifications is supported.The serial terminal of the battery connector is connected toIC1001 on the RE-261 board. This IC1001 reads thebattery authentication, battery type, remaining power, andother information and send them to the system controllervia I2C bus communication.
(5) Power supply voltage detectionThe power supply voltage at the DC IN connector ismeasured by the A/D port on IC1001 on the RE-261 board,and it is posted to the system controller as the input voltagevalue.
(6) Power system controlIC1001 on the RE-261 board checks that the power switchon the PMW-EX3 is turned ON, and turns on the systemcontroller of IC1600. After that, it controls the power foreach circuit block according to the system controller.The system controller controls the respective power supplysystems in the RE-260 and RE-261 boards according to theoperation mode of the device, via the power supply u-processor on the RE-261 board.By turning off the power systems to unnecessary circuitsblocks, power can be saved.
(7) 700P communicationThe serial communication driver (IC803) is mounted onthe TX-129 board.Serial communication with the remote control unit con-nected to the REMOTE connector is performed.
7. SDI/GENLOCK/TC IN/TC OUT
TX-129 board(1) SDI outputThis board receives the parallel video signal with FPGA(IC100) and IC500 and outputs the SDI signal.Furthermore, it performs audio or timecode embedding.The video and audio signals are supplied from CN400 onthe DPR-289A board to CN100 on the TX-129 board witha 0.4 mm pitch, 40-pin fine coaxial cable.The power voltages are supplied from CN401 on the DPR-289A board to CN700 on the TX-129 board with a 15-pinharness.Output SDI signals are supplied to CN500.Output SDI signals are then supplied from CN500 to thecoaxial connector via the mini coaxial connector and minicoaxial cable.The PLL circuit is used to reduce jitter of the HD-SDIclock signal.The FPGA (IC100) is controlled by IC400 on the DPR-289A board through 4-line serial communication.The FPGA program is stored in the IC203 ROM, andJTAG can be used to overwrite the data from IC1600 onthe DPR-289A board.When not using SDI, the power to cable driver insideIC500 is turned off.
(2) GENLOCKIn IC902, sync signal separation is performed for GNE-LOCK. The separated sync signal enters IC400 on theDPR-289A board where phase is compared by the internalcounter of IC400 and by IC521 to control the VCXO(X500).
(3) TC IN/TC OUTIC900, IC901, and IC907 reshape the waveform of thetime code connected to the TC IN connector and input it toIC100.IC903 is the external output circuit for the time code OUTsignal, which outputs the signal to the TC OUT connector.They communicate with the FPGA (IC100) through the 4-line serial interface on the DPR-289A board.
1-10 PMW-EX3
. Power supply reverse connection protectionIf the input power has reverse voltage, Q301 on the RE-260 board is immediately turned off and UNREG poweris stopped on the GND side, and the protection functionworks.
(2) DC/DC converter functionThe power supply output is divided into 25 systems, whichare separated into four blocks as seen below.
. CMOS/camera block system, 7 systems(+4.6 V, +3.1 V, UNREG, etc.)
. Audio/video signal system, 7 systems(+13.5 V, _4.6 V, +4.6 V, etc.)
. System controller system, 5 systems(+4.6 V, +3.1 V, +2.5 V, etc.)
. Media recording/playback system, 6 systems(+3.1 V, +2.5 V, +1.8 V, etc.)
The sequence control (powering up and powering down)for the power supply system is controlled by the POW-ER SUPPLY MICON (power supply u-processor:IC1001) for the respective power supply blocks of eachblock.By turning off the power for each block according to theoperation mode (camera mode or media mode), theoptimal power consumption for each operation isachieved.
. Short-circuit protection for each power supply systemThe circuit settings monitor each output voltage orcurrent for each power supply system and operate theprotection circuits per block.Even after the protection circuit is cleared, automaticrecovery is not performed and the power must be turnedon again.Even after short-circuit is cleared, the protection circuitdoes not recover automatically and the power must beturned on again.
Battery information functions. Battery authentication function
The authentication function checks whether the battery isof the specified type. This helps prevent one cause ofmajor accidents when using batteries as a power supply.If the attached batter is not the specified type of batter,the camera immediately turns off.
. Battery Info functionIn an intelligent (specified) battery, the battery canmonitor information, such as how many times the batteryhas been recycled or the internal temperature for thebattery. This helps provide detailed information aboutthe battery, including whether the battery is damaged orhow long the life is, in order to provide optimal operations.
8. Power supply system
RE-260/261 boardThis board is comprised of the power supply circuit andthe POWER SUPPLY MICON (power supply u-processor:IC1001 on the RE-261 board).However, part of the low-voltage power supply is mountedon the DPR-289A board.
(1) Input power supply (UNREG) system operationsWhen the UNREG power is input, the EVER power stateis established.In this state, the ON/OFF state of the Power switch can berecognized.If the POWER SUPPLY MICON (power supply u-processor: IC1001) recognizes that Power switch is ON,the power is turned on for the system control system andthe POWER SUPPLY MICON (power supply u-processor:IC1001) controls the power supply for each block accord-ing to the system controller (DPR-289A board: IC1600).The normal value for the input power supply (UNREG) isin the range of about +10.5 V to +18 V.
. Battery/EXT-DC selectInput power comes in two systems: Battery and EXT-DC. This switch monitors the input voltage for eachinput and automatically switches the circuit settings withpriority given to EXT-DC.
. Input overvoltage protectionIf the voltage is too high in the UNREG power supply,the overvoltage protection circuit starts operating aroundthe set value of +17.9 V, and the camera shuts down.When the input power supply voltage to this circuitbecomes less than +17.9 V, the power supply immedi-ately switches on with automatic recovery.
. Input low-voltage protectionIf the voltage is too low in the UNREG power supply,the low-voltage protection circuit starts operating aroundthe set value of +10.5 V according to the control by thePOWER SUPPLY MICON (power supply u-processor:IC1001), and the camera shuts down. When the inputpower supply voltage becomes higher than +10.5 V, thepower supply immediately switches on with automaticrecovery according to the control by the POWERSUPPLY MICON (power supply u-processor: IC1001).
. Overcurrent detectionThe overcurrent detection circuit is comprised of IC308on the RE-260 board. The setting value is approximately4.3 (A). Even after clearing IC308 after overcurrentdetection, automatic recovery is not performed and thepower must be turned on again.
PMW-EX3 1-11
1-4. Service Tools/Measuring Equipment List
1-4-1. Service Tools
Part No. Name Usage/Note
1 Commercially available Grayscale chart Reflective type (16 : 9), Camera adjustment on market2 Commercially available Star chart Reflective type, camera adjustment on market3 J-6394-080-A Grayscale chart Transparent type (16 : 9), Camera adjustment on market4 J-6029-140-B Pattern box PTB-500 Camera adjustment5 * Mini USB cable For firmware version-upgrade6 3-292-755-01 XLR JIGU For removing the mounted circuit board7 J-6325-110-A Bit for torque driver (M1.4) For tightening screw
J-6325-380-A Bit for torque driver (M2) For tightening screwJ-6323-430-A Bit for torque driver (M3) For tightening screw
8 J-6326-120-A Hexagon bit (For torque screwdriver) For tightening screw(size 1.5)
9 J-6325-400-A Torque driver (3 kg.cm)(0.3N.m) For tightening screwJ-6252-510-A Torque driver (6 kg.cm)(0.6N.m) For tightening screwJ-6252-520-A Torque driver (10 kg.cm)(1.0N.m) For tightening screw
!/ 7-432-114-11 Locking compound For preventing screw from being loosened!- 7-651-000-10 Sony (SGL-601) 50 g grease Lubricant
* : This cable is supplied with PMW-EX3.
1-4-2. Measuring Equipment
Use the calibrated equipment or equivalent as listed below for the adjustments.Equipment Model name
Oscilloscope Tektronix TDS3054 or equivalent (150 MHz or more)HD waveform monitor LEADER ELECTRONICS CORP.LV5152DA or equivalentFrequency counter Advantest TR5821AK or equivalent
Digital voltmeter Advantest TR6845 or equivalentColor monitor Sony HDM-20E1U/14E1U/14E5U or equivalent
Luminance meter Konica Minolta LS-110 or equivalent
1, 3 2 4 5 6
7 8 9 0 !-
1-12 PMW-EX3
1-5. Firmware Upgrade
Upgrade the firmware for the PMW-EX3 through a USB connection to a computer.For detailed information about the upgrade procedure, check the readme file that comes with the upgradesoftware.For inquiry or comments about the firmware upgrade, please contact your local Sony Sales Office/ServiceCenter.
Firmware Upgrade ProcedureDownload the software for the new firmware upgrade onto the computer before starting these operations.
1. Check that the power switch on the PMW-EX3 is turned OFF.2. Remove the pad sub assembly and pad center cover. (Refer to Section 2-2-3.)
3. Use the USB connector that comes with the PMW-EX3 to connect the computer and the USBmaintenance connector.
4. Switch the power switch to CAMERA and turn the power ON.5. Run the software for the firmware upgrade on the computer.6. When the upgrade is complete, turn OFF the power and remove the USB cable.7. Attach the pad sub assembly and pad center cover.
When the PMW-EX3 is connected to the computer for the first time, the driver software will need to beinstalled into the computer. For more details, check the readme file that comes with the upgrade software.
USB maintenance connector
PMW-EX3 1-13
1-6. Recommended Replacement Parts
This section describes the recommended replacement parts and recommended replacement time.
ID Part name Sony part No. Recommended replacement timing
1 Lens hood 4-110-064-01
2 Eye cup 3-878-208-02
1
2
Check for deformation and deterioration from time to time.Replace it as necessary.
1-14 PMW-EX3
1-7. Note on Service
1-7-1. Requirements on Replacement ofBoards or Parts
This section explains the necessary setups required whenreplacing boards or parts.
1. When any of the following boards is replaced, upgradethe firmware version.All data are written at once when upgrading thefirmware version. (Refer to Section 1-5.)
Board name Ref. No.
DPR-289A IC312, IC603, IC1100, IC1603
KSW-54 IC100SWC-48 IC601ASW-66 IC106
RE-261 IC1001
TX-129 IC203
2. Adjusted values are stored in the following boards andparts. The values need to be readjusted when they arereplaced.
Board/part name Ref. No.
DPR-289A*1
CMOS block IC312/DPR-289A boardLCD module*2 IC202/IF-1072 board, IC603/DPR-
289A board*1: The adjusted values for the CMOS block and the LCD module are
stored in the DPR-289A board.*2: The adjusted values for the LCD module are stored in the LCD module,
but the adjusted values need to be copied to the DPR-289A board.
3. The user setting values are stored in IC1703 on theDPR-289A board. The user data must be stored(Restore) in SxS before replacing the board and it mustbe read (Recall) after replacing the board.
1-7-2. Note on Replacement of Parts on theBoard
1. The BI-202, BI-203 and BI-204 boards cannot bereplaced on the board-level service or part-level service.If parts become defective, replace the entire CMOSblock.
2. Parts labels also cannot be replaced in the DPR-289Aboard.If parts become defective, replace the entire mountedboard.
1-7-3. Description of Number Seal on thePrism
The number seal is put in the prism unit, the serial numberof prism unit.Every prism unit has its own number called prism serialnumber.
1-7-4. Memory Backup Battery
For replacing the battery, refer to Backup Battery of theAppendixes in the Operating Instructions.When the backup battery is replaced, the date and time inthe internal clock need to be set. Refer to Setting theClock of the Preparations in the Operating Instructions.
1-7-5. Unleaded Solder
Boards requiring use of unleaded solder are printed with alead free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not comeprinted with the lead free mark due to their particular size.)
: LEAD FREE MARK
m. Be sure to use the unleaded solder for the printed circuit
board printed with the lead free mark.. The unleaded solder melts at a temperature about 40 dC
higher than the ordinary solder, therefore, it is recom-mended to use the soldering iron having a temperatureregulator.
. The ordinary soldering iron can be used but the iron tiphas to be applied to the solder joint for a slightly longertime. The printed pattern (copper foil) may peel away ifthe heated tip is applied for too long, so be careful.
PMW-EX3 1-15
1-8. Connector Location Diagram onBoard
The PMW-EX3 uses flexible card wires and coaxial cableswith connector. The following diagrams indicate thelocation of each connector. The location of flexible cardcables are indicated by the circle number 1 and 2, whilethe coaxial cables with connector are not indicated by thecircle number.
ASW-66 board (A side) AU-318 board (A side)
AXM-36 board (A side)
DPR-289A board (A side) DPR-289A board (B side)
IF-1069 board (A side )
CN1001
CN1 CN22 2
CN31
CN1
CN400CN402
CN601
CN1804CN1301
CN1300
1
EC-63 board (B side)
CN51
CN4
1
KSW-54 board (A side) KSW-54 board (B side)
SW-1389 board (B side) SW-1410 board (B side)
SWC-48 board (A side)
SWC-49 board (B side) TX-129 board (A side)
CN51
CN41
CN5001
CN7001
CN3001
CN1001
CN100
CN800
IR-42 board (A side )
CN102
CN1032
1
1-16 PMW-EX3
1-10. Replacing the Coaxial Cable withConnector (Fine Pitch Coaxial Cable)
The PMW-EX3 uses coaxial cables with connector.nThe life of the coaxial cable with connector will be signifi-cantly shortened if it is pulled or bent. Be very careful inhandling.
The following precautions must be observed when remov-ing or connecting the coaxial cable with connector.
Note on Disconnecting
The coaxial cable with connector uses fine pitch coaxialcables. Be careful when arranging the cable. When discon-necting the coaxial cable with connector, do not attempt toremove by pulling the cable. Be sure to hold the connectorto remove.
Hold the connector to remove.OK
Do not attempt to remove by pullingthe cables.
NG
A
A
Connector : 1 Connector : 2
Isolation surface(blue)
Isolation surface(blue)
1-9. Replacing the Flexible Card Wires
nThe flat cables, flexible card wires and boards are used toconnect between the following boards. Life of flexible cardwire will be significantly shortened if it is folded. Be verycareful not to fold the flat cables, flexible card wires andboards.The two types of different shape connectors are used inthis unit.Because the direction of the flat cables, flexible card wiresand boards are different depending on the shape of theconnector, be careful when connecting the flat cables,flexible card wires and boards.
Disconnecting
1. Turn off the power.2. Slide or lift up the portion A in the direction of the
arrow to unlock and pull out the flexible card wire.
Connecting
m. Do not insert the coaxial cable with connector sideways.. Confirm that there is no stain or dust on the contact
surface of the coaxial cable with connector.
1. Slide or lift up the portion A in the direction of thearrow and securely insert the flexible card wire intothe deep end of the connector.
2. Return the portion A to its original position and lockthe connector.
nWhen connecting the flexible card wire, check the connec-tor shape, and great care should be taken for the directionof the contact surface or isolation surface (blue).
PMW-EX3 1-17
Hold the connector to connect.OK
Not to bend the cable.NG
Polarity marks
Yellow
Terminal side
Note on Connecting
When connecting the coaxial cable with connector, holdthe connector matching the polarity marks and insert thecoaxial cable straight into the corresponding connector.
1-18 PMW-EX3
1-11. List of Error Numbers on the LCD Display
Error numbers are displayed as E-XXXXX (X indicates a number).
Error No. Description Service action
15030 System error Repair the DPR-289A board or replace it.17001 Abnormality in the Media ID data in Rewrite the media ID data in the EEPROM.*
the EEPROM17002 The image processor block does not start up. Repair the DPR-289A board or replace it.17003 The display block does not start up
17004 The media block does not start up
17005 Abnormality in the start-up process ofthe image processor block
17006 Abnormality in the start-up process ofthe display block
17007 Abnormality in the start-up process ofthe media block
17014 Abnormality in lens communication Check the connection with the lens unit. If there isno defect, replace the lens unit.
17015 Abnormality in the media block Repair the DPR-289A or replace it.
17016 Abnormality in obtaining the lens switch Check the connection with the lens unit. If there isno condition defect, replace the lens unit.
17017 Internal error in the media block Repair the DPR-289A board or replace it.or4XXXX
*: For how to rewrite the media ID data in the EEPROM, contact your local Sony Sales Office/Service Center.
PMW-EX3 2-1
2-1. Outline of Replacement Procedures
. The following figures show the flow for removing the main parts. Refer to Section 2-2 for details of thereplacement procedures.
Section 2Replacement of Main Parts
START
Bottom panel
Bracket(tripod)
Battery
Button battery lid
Pad sub assembly
Pad center cover
Pad cover Handel top coverassembly
Accessory shoe
Spring
Microphone holder assembly
Lens
Connector rear assembly
Front cover handle
HN-337 board
Handle assemblyInside panel assembly
Outside panelsub assembly
TX block
EX-DDassembly
Out side connector assembly
DPR-289A board
Main frameblock
Lens mountblock
Prism blockunit
2-2 PMW-EX3
2-2-2. Bottom Panel
1. Remove the button battery lid. (Refer toSection 2-2-1.)
2. Remove the four screws (M2 x 6), andremove the bracket (tripod).
3. Remove the four screws (M2 x 4), andremove bottom panel.
3. Reinstall the lithium battery by reversing thesteps of removal.
Battery holderLithium battery
Button battery lid
Lithium battery removal
Lithium battery
M2 x 4(Black)
Bottom panel
Bracket (tripod)
M2 x 4(Black)
M2 x 6(Black)
2-2. Replacement Procedures
n. When tightening screw, be sure to tighten it with the specified tightening torque.. When reinstalling the removed tapping screw again, tighten it with slightly loose torque not to damage the threads of the
component side.. If the tightening torque is not specified in a specific item, use the tightening torque as specified below.
M2 (+) screw: 18 x 10-2 0.02 N.m (1.8 0.2 kgf.cm)M2.6 (+) screw: 53 x 10-2 0.07 N.m (5.3 0.7 kgf.cm)M3 (+) screw: 80 x 10-2 0.01 N.m (8.0 0.1 kgf.cm)
2-2-1. Lithium Battery
1. Loosen the screw, and remove the buttonbattery lid.
2. Remove the lithium battery.
4. Reinstall the removed parts by reversing thesteps of removal.
PMW-EX3 2-3
2-2-3. Pad Sub Assembly, Pad Cover
1. Press the pad stopper in the direction of thearrow A, while the pad stopper is beingunlocked, lift up the pad sub assembly in thedirection of the arrow B.
2. Remove the screw, and remove the padcenter cover.
3. Press the pad stopper in the direction of thearrow A, while the pad stopper is beingunlocked, remove the pad sub assembly inthe direction of arrow B.
A
B
Pad stopper
Pad sub assembly
Pad center cover
B2.6 x 6(Black)
Pad cover
M2 x 4(Black)
4. Remove the four screws, and remove the padcover.
5. Reinstall the removed parts by reversing thesteps of removal.
2-4 PMW-EX3
2-2-4. LCD Assembly, CT-251 Board
1. Remove the four screws (black), and removethe display plate and the LCD cover.
2. Remove the four screws (silver) of the LCDassembly.
3. Disconnect the coaxial cable with connectorfrom the connector, and remove the LCDassembly.nThe coaxial cable with connector uses thefine pitch coaxial cable. Be careful whenarranging the harness. When disconnectingthe coaxial cable with connector, neverremove it by pulling the harness. Be sure tohold the connector to remove.
Connector
Coaxial cable with connectorM2 x 4
(Silver)
M2 x 4(Silver)
M2 x 4(Black)
M2 x 4(Black)
Display plate
LCD coverLCD assembly
CN1
CT-251 board
M2 x 4(Silver)
M2 x 4(Silver)
Harness4. Remove the three screws from the CT-251board.
5. Disconnect the harness from the connector(CN1), and remove the CT-251 board.
7. Reinstall each part by reversing steps 1 to 3.mWhen connecting the coaxial cable withconnector, be careful of the following points:. Do not insert the connector at a slant angle.. Check to see that the contacting surface is
free from stain and dust.. Hold the connector with its contacting
surface facing upward, and check that thepolarity marks are aligned.
Insert the cable by holding the connector.
Do not bend the cable.
NGOK
Contacting surface
Polarity marks ( )
Knob(MIRROR IMAGE)
CN1S3
CT-251 board
M2 x 4(Silver)
M2 x 4(Silver)
Harness
6. Reinstall the removed parts by reversingsteps 4 to 5.nCheck that the switch (S3) on the CT-251board engages with the knob (MIRRORIMAGE).
PMW-EX3 2-5
2-2-5. Handle Top Cover Assembly
1. Open the microphone holder assembly.2. Remove the two screws, and remove the
microphone holder assembly.
Microphone holder assembly
B2.6 x 6 (Black)
SpringClaws
Accessoryshoe
M2 x 4 (Black)
M2 x 6(Black)
Handle top cover assembly
3. Remove the spring and the four screws (M2x 6), and remove the accessory shoe.
4. Remove the five screws (M2 x 4). Whiledisengaging the two claws, remove thehandle top cover assembly.
5. Reinstall the removed parts by reversing thesteps of removal.
2-6 PMW-EX3
2-2-6. KSW-54 Board, Control SwitchBlock
1. Refer to Section 2-2-5 and remove theHandle Top Cover Assembly.
2. Remove the rubber switch key.3. Disconnect the HN-349 board from the
connector (CN5).4. Disconnect the three harnesses from the three
connectors (CN2, CN7 and CN301).
Harness Harness
Harness
HN-349 board
Rubber switch key
KSW-54 board
CN301 CN5 CN7 CN2
Control switch block
Harness
HN-328 board
PSW2 x 5(Silver)
M2 x 4 (Silver)CN300CN4
CN1
M2 x 4(Silver)
PSW2 x 5(Silver)
KSW-54 board
5. Remove the three screws (PSW2 x 5)securing the control switch block.
6. Remove the four screws (M2 x 4) securingthe KSW-54 board.
7. Disconnect the harness from the connector(CN300) on side-B of the KSW-54 board.
8. Disconnect the control switch block from theconnector (CN4) on side-B of the KSW-54board.
9. Disconnect the HN-328 board from theconnector (CN1) on side-B of the KSW-54board.
10. Reinstall the removed parts by reversing thesteps of removal.
PMW-EX3 2-7
2-2-7. IF-1069 Board, LED-469 Board
1. Refer to Section 2-2-5 and remove theHandle Top Cover Assembly.
2. Disconnect the flexible flat cable from theconnector (CN4) on the IF-1069 board.
3. Disconnect the HN-348 board from theconnector (CN5) on the IF-1069 board.
4. Disconnect the harness from the connector(CN3) on the IF-1069 board.
5. Remove the two screws, and remove the IF-1069 board.
6. Disconnect the three harnesses from the threeconnectors (CN1, CN2 and CN3) on theLED-469 board.
7. Remove the screw, and remove the LED-469board.
S1
KnobIF-1069 board
10. Reinstall the removed parts by reversingsteps 1 to 5.nCheck that the switch (S1) on the IF-1069board engages with the knob.
Harness
Knob
HN-348 board
Flexible flat cable
LED-469 board
HP-144 board
M2 x 4(Silver)
M2 x 4(Silver)
S1 CN3
CN4
CN5
CN1 CN3
CN2
M2 x 4(Silver)IF-1069 board
CN2 Arrange the extra length of the harness so that it is completely housed inside the space in the deep end and should not come outside the space.
Extra length of harness
8. Reinstall the removed parts by reversingsteps 6 to 7.
9. Arrange the extra length of the harnesscoming from the connector (CN2) as de-scribed in the illustration.
2-8 PMW-EX3
2-2-8. AXM-36 Board, HN-349 Board
1. Refer to Section 2-2-5 and remove theHandle Top Cover Assembly.
2. Remove the rubber switch key.3. Remove the two screws (B2.6 x 6 : Silver),
and remove the out microphone bracket.4. Disconnect the HN-349 board from the
connector (CN5) on the KSW-54 board.5. Remove the four screws (P2.6 x 6 : Black),
and remove the AXM-36 board in thedirection of the arrow.
6. Disconnect the HN-349 board from theconnector (CN3) on the AXM-36 board.
AXM-36 board
KSW-54 board
CN5
CN3
HN-349 board
Out microphone bracket
P2.6 x 6(Black)
B2.6 x 6(Silver)
P2.6 x 6(Black)
Rubber switch key
7. Reinstall the removed parts by reversing thesteps of removal.nWhen installing the screws that were re-moved in step 5, tighten them with thespecified tightening torque.Tapping P2.6 x 6 tightening torque:80 x 10-2 0.15 N.m (8.0 1.5 kgf.cm)
PMW-EX3 2-9
2-2-9. Handle Assembly
1. Refer to Section 2-2-5 and remove theHandle Top Cover Assembly.
2. Remove the two screws (B2.6 x 6), andremove the rear shoe bracket.
3. Disconnect the harness from the connector(CN1) on the HP-144 board.
4. Remove the connector cover (HP) and thetwo screws (M2 x 4), and remove the HP-144 board.
5 Remove the lens from the main unit.
Lens
HP-144 board
CN1
M2 x 4 (Silver)
B2.6 x 6(Silver)
Rear shoe bracket
Connector cover (HP)
Main unit
Front cover handle
Handle assembly
HN-343 board CN800
Flexible flat cable
Coaxial cable with connector
DPR-289A board connector
HN-328 board CN2
IF-1069 board CN4
LED-469 board CN2
M2 x 4(Black)
B2.6 x 6(Silver)
B2.6 x 6(Silver)
6. Disconnect the flexible flat cable from theconnector (CN4) on the IF-1069 board.
7. Disconnect the harness from the connector(CN2) on the LED-469 board.
8. Remove the two screws (M2 x 4), andremove the front cover handle.
9. Disconnect the connector (CN2) of the HN-328 board from the connector (CN800) on theHN-343 board.
10. Remove the three screws (B2.6 x 6). Lift upthe handle assembly gently and disconnectthe coaxial cable with connector from theDPR-289A board connector.nThe handle assembly is connected to theDPR-289A board by the coaxial cable withconnector.When disconnecting the coaxial cable withconnector, be very careful not to applyphysical load to the coaxial cable withconnector.
2-10 PMW-EX3
11. Reinstall the removed parts by reversingsteps 7 to 10.nArrange the extra length of the harnesscoming from the connector (CN2) of theLED-469 board as described in the illustra-tion.
CN2 Arrange the extra length of the harness so that it is completely housed inside the space in the deep end and should not come outside the space.
Extra length of harness
12. Reinstall each part by reversing steps 2 to 6.13. Connect the harness to the connector (CN1)
on the HP-144 board, and route the harnessbetween the rear shoe bracket and the HPjack. Then route the harness along theunderside of the HP jack.
HP-144 boardCN1
HP jack
Rear shoe bracket
14. Refer to Section 2-2-5 and reinstall theHandle Top Cover Assembly.
PMW-EX3 2-11
2-2-10. Microphone Assembly
1. Refer to Sections 2-2-5, 2-2-6 and 2-2-9, andremove the Handle Assembly removal.
2. Turn the lock lever in the direction of arrowA, loosen the two screws of a, and removethe lock lever.
3. Remove the two screws securing the frontbottom cover.
4. While pushing the front bottom cover in thedirection of arrow B paying attention not todamage the three claws, remove the frontbottom cover in the direction of arrow C.
5. Remove the two screws, and pull out themicrophone assembly in the direction ofarrow D.
A
C
B
D
Microphone assembly
Claws
Lock lover
Loosen screws of a.
a : Double-point set screw
Front bottom cover
M2 x 4 (Black)
M2 x 4 (Black)
M2 x 4 (Black)
Harness
Harness should not run on top of this area. 6. Reinstall the removed parts by reversing
steps 1 to 5.nArrange the extra length of the harnesscoming from the VF slide arm in the direc-tion shown by the arrow. Confirm that theharness does not run on top of the area shownin the illustration.
2-12 PMW-EX3
7. Tighten the lock screw with specified torque.Lock screw tightening torque:95 x 10-2 0.02 N.m (9.5 0.2 kgf.cm)
8. Install the lock lever to the lock screw so thatprotrusion of the lock lever is positioned nextto protrusion of the arm case.
Lock screw
Protrusions are next to each other.
Protrusions are next to each other.
9. Apply a small amount of the thread lockingadhesive agent to the screw tip of the twoscrews a.
10. While the state established by step 8 ismaintained, attach the two screws a.Screw a tightening torque:50 x 10-2 0.05 N.m (5.0 0.5 kgf.cm)nTurn the lock lever fully counterclockwiseand confirm that the VF assembly can movesmoothly in the directions of A and B asshown by the arrow.
[A]
[B]
Lock lever
Screws a
VF assembly
11. Reinstall each part by reversing step 1.
PMW-EX3 2-13
2-2-11. Microphone Unit, MA-164Board, RM-214 Board
1. Refer to Sections 2-2-5, 2-2-6, 2-2-9 and 2-2-10, and disassemble the unit up to Micro-phone Assembly removal.
2. Remove the shield sheet.3. Remove the three screws of a, and remove
the microphone case.4. Remove the screw of b, and remove the
microphone unit.
Microphone case
Microphone unit
Microphone cover
Shield sheets
a
b
a : P2 tapping 2 x 5b : P2 tapping 2 x 5
Harness
MA-164 board
CN3
CN2
CN1
CN1 Microphone unit
Harnesses
RM-214 board Harness
c
d
c : P2 tapping 2 x 5d : P2 tapping 2 x 5
5. Disconnect the three harnesses from the threeconnectors (CN1, CN2 and CN3) on the MA-164 board.
6. Remove the two screws of c, and removethe MA-164 board.
7. Disconnect the harness from the connector(CN1) on the RM-214 board.
8. Remove the screw of d, and remove theRM-214 board.
9. Reinstall the removed parts by reversing thesteps of removal.nWhen reinstalling the removed tapping screwagain, refer to note of section 2-2. Replace-ment Procedures.
2-14 PMW-EX3
2-2-12. SWC-49 Board
1. Refer to Sections 2-2-5, and 2-2-9, anddisassemble the unit up to Handle Assem-bly removal.
2. Disconnect the HN-348 board from theconnector (CN100) on the SWC-49 board.
3. Remove the two screws, and remove the toppanel cover.
HN-348 board
Top panel cover
SWC-49 board CN100 M2 x 4 (Silver)
Top panel cover
Key top assembly(top panel)
SWC-49 board
Top panel earth bracket
Tapping2 x 5 (Black)
4. Remove the two screws. Remove the toppanel earth bracket, the SWC-49 board andthe key top assembly (top panel).
5. Reinstall the removed parts by reversing thesteps of removal.nWhen reinstalling the removed tapping screwagain, refer to note of section 2-2. Replace-ment Procedures.
PMW-EX3 2-15
2-2-13. Inside Panel Assembly
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5and 2-2-9, and disassemble the unit up toHandle Assembly removal.
2. Remove the two connector covers from theconnectors.
3. Disconnect the HN-344 board connector(CN100) from the AU-318 board connector(CN4) that is located in the bottom of the unitby skewer.
4. Remove the five screws (silver) and thescrew (black). Disengage the six protrusionsof the inside panel from the corresponding sixdowels.
Connector covers
M2 x 4(Silver)
M2 x 4 (Black)
M2 x 4(Silver)
Dowel
Inside panel assembly
Protrusion of inside panel Connector
HN-344 boardCN100
AU-318 boardCN4
Inside panel assembly
B
A Inside panel assembly
Holes of inside panel assembly
Connectors
HN-337 board CN2
ASW-66 board CN101
8 Reinstall the removed parts by reversing thesteps of removal.
5. Remove the inside panel assembly slightly inthe direction of arrow A.
6. Disconnect the six connectors and removethem through the six holes, and remove theinside panel assembly in the direction ofarrow B.
7. Disconnect the connector (CN2) of the HN-337 board from the connector (CN101) of theASW-66 board, and remove the inside panelassembly.
2-16 PMW-EX3
2-2-14. CN-3050 Board
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5,2-2-9 and 2-2-13, and disassemble the unit upto Inside Panel Assembly removal.
2. Disconnect the harness from the connector(CN1) on the CN-3050 board.
3. Remove the two screws (tapping 2 x 5) andthe screw (M2 x 4), and remove the EMCbracket (rear top) and the CN-3050 board.
CN-3050 board
Tapping2 x 5(Black)
M2 x 4(Silver)
CN1
Frame notch
EMC bracket(rear top)
4. Reinstall the removed parts by reversing thesteps of removal.m. When connecting the harness to the
connector (CN1) on the CN-3050 board,arrange the harness so that it is routedinside the notch of the frame and inside thehatched portion.
. When reinstalling the removed tappingscrew again, refer to note of section 2-2.Replacement Procedures.
PMW-EX3 2-17
2-2-15. Connector Rear Assembly
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5,2-2-9, 2-2-13 and 2-2-14 and disassemble theunit up to CN-3050 board removal.
2. Disconnect the power supply harness fromthe connector (CN2) on the RE-260 board.
3. Remove the screw a (B2.6 x 6) and disen-gage the two claws. Then remove the EMCbracket (main).
4. Remove the three screws b (B2.6 x 6), andremove the Connector rear assembly.
5. Disconnect the harness from the connector(CN6) on the CN-3024 board.
6. Disconnect the coaxial cable assembly fromthe coaxial connector, and remove theconnector rear assembly.
CN-3024 boardCN6
RE-260 boardCN2
Power supply harness
Coaxial cable assembly
Coaxial connectorClaws
Connector rear assembly
EMC bracket(main)
Screws b
Screw a
Screws b(Silver)
Screws a(Silver)
7. Reinstall the removed parts by reversing thesteps of removal.
2-18 PMW-EX3
2-2-16. ASW-66 Board, SW-1412Board
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5,2-2-9 and 2-2-13, and disassemble the unit upto Inside Panel Assembly removal.
2. Disconnect the harnesses and the AU volumeblock from the three connectors (CN100,CN102 and CN103) on the ASW-66 board.
3. Release the harness from the two claws of theinside panel assembly. (Refer to Fig. 2.)
4. Remove the four screws, and remove theASW-66 board in the direction of the arrow.(Refer to Fig. 1.)
5. Remove two pieces of the AU slide switch(1) and two pieces of the AU slide switch (2)of the ASW-66 board from the correspondingAU slide levers. (Refer to Fig. 1.)nBe careful not drop the AU slide switches soas not to lose them.
6. Remove the AU slide switch guide from theASW-66 board. (Refer to Fig. 1.)
7. Disconnect the harness from the connector(CN100) on the SW-1412 board.
8. Remove the two screws, and remove the SW-1412 board.nBe careful not to make mistake the AU slideswitch (1) for the AU slide switch (2)because they are different in size.
ASW-66 board
ASW-66 board
Harness
SW-1412 boardAU volume block
Inside panel assembly
SW-1412 board
CN103
CN102
CN100
CN100Tapping2 x 5(Black)
Tapping2 x 5(Black)
(Fig. 2)
Claws of inside panel assembly
AU slide switch lever
Knob of AU slide switch (Fig. 1)
ASW-66 board
S100
S102
S103
S101
AU slide switches (1)
AU slide switches (2) AU slide switch guide
9. Reinstall the removed parts by reversing thesteps of removal.m. Check that the four knobs of the AU slide
switch are normally engaged with the fourcorresponding switches (S100 throughS103) on the ASW-66 board.
. When reinstalling the removed tappingscrew again, refer to note of section 2-2.Replacement Procedures.
PMW-EX3 2-19
2-2-17. SW-1410 Board
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5,2-2-9 and 2-2-13, and disassemble the unit upto Inside Panel Assembly removal.
2. Disconnect the SWC-48 board from theconnector (CN300) on the SW-1410 board.
3. Remove the three screws, and remove theSW-1410 board.
4. Remove the power switch from the powerswitch lever of the SW-1410 board.
5. Remove the power switch slide rail from theSW-1410 board.
nBe careful not to drop and lose the power switch.
SW-1410 board
SW-1410 boardPower switch
Power switch lever
Knob of power switchPower switch slide rail
SWC-48 board
Inside panel assembly
CN300
Tapping2 x 5(Black)
S301
S301
6. Reinstall the removed parts by reversing thesteps of removal.m. Check that the knob of the power switch is
normally engaged with the switch (S301)on the SW-1410 board.
. When reinstalling the removed tappingscrew again, refer to note of section 2-2.Replacement Procedures.
2-20 PMW-EX3
2-2-18. HN-344 Board
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5,2-2-9 and 2-2-13, and disassemble the unit upto Inside Panel Assembly removal.
2. Disconnect the SWC-48 board from theconnector (CN300) on the SW-1410 board.
3. Remove the four screws, and remove theinside panel assembly (1).
4. Disengage the two claws, and remove the CNholder.
5. Disconnect the HN-344 board connector(CN101) from the SWC-48 board connector(CN100).
SW-1410 boardCN300
HN-344 boardCN101
SWC-48 boardCN100
CN holder
Claws
SWC-48 board
Tapping2 x 5(Black)
Inside panel assembly (2)
Inside panel assembly (1)
6. Reinstall the removed parts by reversing thesteps of removal.nWhen reinstalling the removed tapping screwagain, refer to note of section 2-2. Replace-ment Procedures.
PMW-EX3 2-21
2-2-19. HN-343 Board, SWC-48 Board
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5,2-2-9, 2-2-13 and 2-2-18, and disassemblethe unit up to HN-344 Board removal.
2. Remove the tape (LED) fixing the ferritecore.
3. Remove the two screws (M2 x 4) of a, anddisconnect the HN-343 board from theconnector (CN700) on the SWC-48 board.
4. Remove the tape (SWC48) and ferrite corefrom the HN-343 board.
5. Disconnect the harness from the connector(CN600) on the SWC-48 board. Disconnectthe harness from the bracket (frame/full autobracket) in the direction of the arrow.
6. Remove the three tapping screws (2 x 5) ofb and the three screws (M2 x 4) of c, andremove the SWC-48 board. a
b
c
HN-343 board
SWC-48 board
CN700Ferrite core
Tape (LED)
Tape(SWC48)
Harness
Bracket (Frame/full auto bracket)
CN600
M2 x 4(Silver)
M2 x 4 (Silver)
Inside panel assembly (1)
Inside panel assembly (1)
Tapping2 x 5(Black)
Screws c
2-22 PMW-EX3
7. Remove the top key (frame) and the lightinterception cushion from the SWC-48 board.
8. Remove the tape (SWC48) from the SWC-48board.
9. Remove the three screws, and remove theSWC-48 board from the bracket (frame/fullauto bracket).
Fold
SWC-48 board
Hole of SWC-48 board
Volume10. Reinstall the removed parts by reversing the
steps of removal.m. Do not re-use the tape on which adhesive
agent is coated.. When reinstalling the removed tapping
screw again, refer to note of section 2-2.Replacement Procedures.
Bracket (Frame/full auto bracket)
SWC-48 board
Top key (frame)
Light interception cushion
M2 x 4(Silver)
M2 x 4(Silver)
SWC-48 board
Tape (SWC48)
Bracket (Frame/full auto bracket)
PMW-EX3 2-23
Tapping2 x 5(Black)
SW-1411 board
CN400
Harness Light interception spacers
Inside panel assembly (1)
M2 x 4(Silver)
M2 x 4(Silver)
M2 x 4(Black)
Dowel
Main unitProtrusion of outside panel sub assembly
Outside panel subassembly
3. Reinstall the removed parts by reversing thesteps of removal.nWhen installing the outside panel subassembly (to be abbreviated as O-assemblyhereafter), stand the unit and the O-assemblyvertically. Then, move the O-assemblytoward the unit in parallel with the unit, andinstall the O-assembly.Do not install the O-assembly at an angle.
5. Reinstall the removed parts by reversing thesteps of removal.nWhen reinstalling the removed tapping screwagain, refer to note of section 2-2. Replace-ment Procedures.
2-2-20. SW-1411 Board
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5,2-2-9, 2-2-13, 2-2-18 and 2-2-19, anddisassemble the unit up to SWC-48 Boardremoval.
2. Disconnect the harness from the connector(CN400) on the SW-1411 board.
3. Remove the four screws, and remove theSW-1411 board.
4. Remove the two light interception spacersfrom the inside panel assembly (1).
2-2-21. Outside Panel Sub Assembly
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5and 2-2-9, and disassemble the unit up toHandle Assembly removal.
2. Remove the five screws (silver) and thescrew (black). Disengage the six protrusionsof the outside panel sub assembly from thecorresponding six dowels, and remove theoutside panel sub assembly in the direction ofthe arrow.
2-24 PMW-EX3
2-2-22. SW-1389 Board
1. Refer to Sections from 2-2-1 to 2-2-3, 2-2-5,2-2-9, 2-2-13 and 2-2-21, and disassemblethe unit up to Outside Panel Sub Assemblyremoval.
2. Disengage the claw and the two dowels of thefront panel from the SW board bracket.
3. Disconnect the HN-345 board from theconnector (CN2) on the AU-318 board.
4. Remove the two screws, and remove the SW-1389 board.
5. Disconnect the HN-345 board from theconnector (CN500) on the SW-1389 board.
Claw of SW board bracket
SW-1389 board
Front panel assembly
M2 x 4(Silver) AU-318 board CN2
Claws
HN-345 b
Recommended