View
6
Download
0
Category
Preview:
Citation preview
STEELPUMPS srl - Via Sicilia - Z. I. Perignano56035 Lari (PI) ITALY
+39 0587 466722 / +39 0587 466188+39 0587 466775 / +39 0587 466747
FAX +39 0587 365138
e-mail: info@steelpumps.it
venditeitalia@steelpumps.ittecnico@steelpumps.it
assistenza@steelpumps.it
www.steelpumps.it
Company headquarter Project Production Quality control
CG
LP02
- 02
018
- ED
GB
2018GENERAL CATALOGUE
P R I C E L I S T
ITALIAN PRODUCT
50Hz
GEN
ERA
L C
ATA
LOG
UE
2018
5
0H
z
To obtain this innovative, completely automatic
and self-contained electropump, Steelpumps
has adopted the clients’ point of view. The
achieved result is a range of pumps, capable
of satisfying different needs.
It is reliable, easy to install and use.
“The different pump”
www.steelpumps.it
GRAFICAFranco Ferrucci
STAMPATipografia Monteserra
COPYRIGHTSteelpumps srl
Printed in Italy
Steelpumps Srl reserves the right to make changes to its products without prior notice
Applications
2
Thanks to the technology UP-DOWN Water our pump is suitable for surface or submersed installation, with no other equipments.
Domestic irrigation and boosting
Surface pumpBoosting and domestic irrigation
Surface pump
Boosting and domestic irrigation
Pump installed in underground well
Feeding and emptying / boosting
Submersed pump
3
Plus control board
ELECTRONIC SYSTEM
Antiblocking system 72H
Dry running protection
Automatic restore after dry-run alarm
Fast ON-OFF switching
STOP
AUTO
Optional Configurations
ON-OFFA U T O
External capacitor systemPump with external capacitor, ON-OFF switch and electrical cable 9 m with Schuko plug
The automatic pumps Steelpumps can be supplied with different configurations. These different options make the product unique and very flexible, suitable and exclusive for each kind of installation.
Minimum level float switch systemPump with float ON-OFF switch to avoid the alarm for dry running
Integrated soft-startPump with SOFT-START electronic board for a modular starting and stopping .
4
ON-OFFA U T O
SOFT START
EXTCAPACITOR
Optional Configurations
Pump in surface, suction from tank
5
1 Isolation valve2 No return valve3 Pumps4 Expansion tank
Min 2,5 mt
Max
10
mt
1
4
2 3
Pump submersed in a tank
Priming of pump
For the first starting, in order to avoid the dry-running that could damage the pump, it is necessary to prime the pump. Start the pump only after having filled it totally with water (about 4l) through the upper hole.
1 Isolation valve2 No return valve3 Pump4 Expansion tank
Min 2,5 mt
Max
10
mt
12
1
4
3
Products identity
6
X A J E 1 2 0 B T C E
Identification code product
Series
Nominal power (HP)
A AutomaticSS Automatic with Soft-Start– Manual1 Booster set2 Booster set with 2 pumps3 Booster set with 3 pumps
JE Self-priming JETMO Horizontal multistageMV Vertical multistageMOV Vertical pre-assembled multistageJV Self-priming vertical JETMF Multistage for fountainsMN Centrifugal single-stage
CE External capacitorFLO FloaterHF High-flow
B Stainless steel hydraulic body
Techopolymer flange
P
Technopolymer hydraulic body and flange Stainless steel hydraulic body
– Brass flange
T Three-phase motor– Single-phase motor
7
Tests applied:- Pressure test and flow rate water (hydraulic characteristics)- Pressure switch test (calibration of the starting pressure / value bar)- Air sealed test (IP68)- Electrical test (motor / electronic board)
Tested products individually
CE External capacitorFLO FloaterHF High-flow
B Stainless steel hydraulic body
Techopolymer flange
P
Technopolymer hydraulic body and flange Stainless steel hydraulic body
– Brass flange
All the Steelpumps pumps are te-sted singularly before the packaging and the shipment. Inside the box the users can find the “Identity card” of the product that certifies the correct functioning.
Pump identification
Pump code
Electric data
Depth immersion
Hydraulic performances
Room temperature Serial number
Protection class
Electric insulation
Capacitor
DutyPower and consumptionOrigin of manufacturer
Model Main features Installation
Self-
prim
ing
Stan
dard
pr
imin
g
Auto
mat
ic
Subm
erge
d
Outd
oor
Gard
en
Unde
rgro
und
XAJE ● ● ● ● ● ●
XAJVP ● ● ● ● ●
XAJE24 ● ● ● ● ● ●
XMN ● ● ● ●
XAMO ● ● ● ● ● ●
XAMV ● ● ● ●
XAMOVB ● ● ● ● ●
XAMVHF ● ● ● ●
XAMOHF ● ● ● ●
XMF ●
KRJE ● ● ●
KRMO ● ● ●
KRSJE ● ● ●
X1AMO ● ● ● ●
X1AJE ● ● ●
X2-MO/MV ● ● ●
X3MV ● ● ●
XMARE ●
WP15 ●
XV4 ●
XV4X ●
The rangeApplications table
Legend
8
Water supply
Rainwater employment
Irrigation and water plays
Water supply from tank and well
Power boilers
Booster sets
Car wash
Industrial use
Sea water application
Well suction
Main applications
● ● ● ● ●
● ● ● ● ●
● ●
● ● ● ● ● ●
● ● ● ● ● ●
● ● ● ● ● ●
● ● ● ● ● ● ●
● ● ● ● ● ● ●
●
●
●
●
●
●
●
● ●
●
●
●
9
XAJE PSelf-priming Jet centrifugal pump with electronic system
DescriptionUp/Down technology for submersed, surface or underground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body: Stainless steel AISI 304• Technopolymer flange and pump body• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
10
MA
N 1
-PH XJE80P 0,60 0,8 - - 4,5 16 40 33 30 24 20 15 - 346,00 447 204 226 163 136 1"¼ 1" 11,5
XJE100P 0,75 1 - - 5,3 16 47 40 35 30 25 20 5 354,00 477 204 226 163 136 1"¼ 1" 12
XJE120P 0,90 1,2 - - 5,9 18 51 45 40 34 30 24 8 361,00 477 204 226 163 136 1"¼ 1" 13
MA
N 3
-PH XJE80PT 0,60 0,8 2,2 1,5 - - 40 33 30 24 20 15 - 348,00 447 204 226 163 136 1"¼ 1" 11,5
XJE100PT 0,75 1 3 1,9 - - 47 40 35 30 25 20 5 355,00 477 204 226 163 136 1"¼ 1" 12
XJE120PT 0,90 1,2 3,6 2,3 - - 51 45 40 34 30 24 8 361,00 477 204 226 163 136 1"¼ 1" 13
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAJE80P 0,60 0,8 - - 4,5 16 40 33 30 24 20 15 - 405,00 447 204 226 163 136 1"¼ 1" 11,5
XAJE100P 0,75 1 - - 5,3 16 47 40 35 30 25 20 5 407,00 477 204 226 163 136 1"¼ 1" 12
XAJE120P 0,90 1,2 - - 5,9 18 51 45 40 34 30 24 8 415,00 477 204 226 163 136 1"¼ 1" 13AU
TO 1
-PH
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
XAJE P
Self-priming Jet centrifugal pump with electronic system
Curves and performance η = 2900 1/min
Materials• Motor body: Stainless steel AISI 304• Technopolymer flange and pump body• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Technopolymer impeller
Cable fixing handle
Motor body with delivery mouth
Technopolymer motor support
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
11
12010080
XAJE BSelf-priming Jet centrifugal pump with electronic system
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body and pump body: Stainless steel AISI 304• echnopolymer flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
12
MA
N 1
-PH XJE80B 0,60 0,8 - - 4,5 16 40 33 30 24 20 15 - 382,00 447 200 226 163 136 1"¼ 1" 14,5
XJE100B 0,75 1 - - 5,3 16 47 40 35 30 25 20 5 391,00 477 200 226 163 136 1"¼ 1" 15
XJE120B 0,90 1,2 - - 5,9 18 51 45 40 34 30 24 8 398,00 477 200 226 163 136 1"¼ 1" 16
MA
N 3
-PH XJE80BT 0,60 0,8 2,2 1,5 - - 40 33 30 24 20 15 - 386,00 447 200 226 163 136 1"¼ 1" 14,5
XJE100BT 0,75 1 3 1,9 - - 47 40 35 30 25 20 5 395,00 477 200 226 163 136 1"¼ 1" 15
XJE120BT 0,90 1,2 3,6 2,3 - - 51 45 40 34 30 24 8 402,00 477 200 226 163 136 1"¼ 1" 16
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensionis mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAJE80B 0,60 0,8 - - 4,5 16 40 33 30 24 20 15 - 437,00 447 200 226 163 136 1"¼ 1" 14,5
XAJE100B 0,75 1 - - 5,3 16 47 40 35 30 25 20 5 440,00 477 200 226 163 136 1"¼ 1" 15
XAJE120B 0,90 1,2 - - 5,9 18 51 45 40 34 30 24 8 442,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
XAJE B
Self-priming Jet centrifugal pump with electronic system
Materials• Motor body and pump body: Stainless steel AISI 304• echnopolymer flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Technopolymer impeller
Cable fixing handle
Motor body with delivery mouth
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
13
12010080
Technopolymer motor support
Curves and performance η = 2900 1/min
XAJESelf-priming Jet centrifugal pump with electronic system
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Me chanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
14
MA
N 1
-PH XJE80 0,60 0,8 - - 4,5 16 40 33 30 24 20 15 - 560,00 447 200 226 163 136 1"¼ 1" 14,5
XJE100 0,75 1 - - 5,3 16 47 40 35 30 25 20 5 572,00 477 200 226 163 136 1"¼ 1" 15
XJE120 0,90 1,2 - - 5,9 18 51 45 40 34 30 24 8 590,00 477 200 226 163 136 1"¼ 1" 16
MA
N 3
-PH XJE80T 0,60 0,8 2,2 1,5 - - 40 33 30 24 20 15 - 568,00 447 200 226 163 136 1"¼ 1" 14,5
XJE100T 0,75 1 3 1,9 - - 47 40 35 30 25 20 5 582,00 477 200 226 163 136 1"¼ 1" 15
XJE120T 0,90 1,2 3,6 2,3 - - 51 45 40 34 30 24 8 596,00 477 200 226 163 136 1"¼ 1" 16
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAJE80 0,60 0,8 - - 4,5 16 40 33 30 24 20 15 - 599,00 447 200 226 163 136 1"¼ 1" 14,5
XAJE100 0,75 1 - - 5,3 16 47 40 35 30 25 20 5 636,00 477 200 226 163 136 1"¼ 1" 15
XAJE120 0,90 1,2 - - 5,9 18 51 45 40 34 30 24 8 640,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
Self-priming Jet centrifugal pump with electronic system
Technopolymer impeller
Front basis
Motor body with delivery mouth
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
15
12010080
Brass motor support
XAJE
Curves and performance η = 2900 1/min
XAJE 24
16
Code
P2Nom.
Low voltage 24 V Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60Volt Amp A N H H1 N1 DNM DNAkW Hp Total Hm in CA
XAJE10024 0,45 0,6 24 29 40 33 30 24 20 15 - 1.090,00 447 200 226 163 136 1"¼ 1" 15AU
TO 1
-PH
Self-priming Jet centrifugal pump with electronic system 24V
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Applications• Boat boosting• Temporary installations• Tank drainage • Hydraulic systems powered by solar energy• Pressurization station for electrically powered utilities with rechargeable batteries
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber • A2 Stainless steel bolts• NBR70 O-ring• H07RN-F Electric cable 2x6 mm ² 5 m• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors • Permanent magnet DC motors
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AIS I316 (standard equipment in automatic version)
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
XAJE 100 24
0 10 20 30 40 50 60 700
5
10
15
20
25
100
η %
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
100
Wat
t
Power
l/min
17
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber • A2 Stainless steel bolts• NBR70 O-ring• H07RN-F Electric cable 2x6 mm ² 5 m• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors • Permanent magnet DC motors
XAJE 24
Technopolymer impeller
Front basis
Motor body with delivery mouth
Brass motor support
Curves and performance η = 2900 1/min
XAJV PSelf-priming Jet centrifugal pump with electronic system Description
Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body: Stainless steel AISI 304• Technopolymer flange and pump body• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
18
MA
N 1
-PH XJV80P 0,60 0,8 - - 4,5 16 40 33 30 24 20 15 - 439,00 505 218 420 36 1"¼ 1" 12
XJV100P 0,75 1 - - 5,3 16 47 40 35 30 25 20 5 446,00 535 218 420 36 1"¼ 1" 12,5
XJV120P 0,90 1,2 - - 5,9 18 51 45 40 34 30 24 8 452,00 535 218 420 36 1"¼ 1" 13,5
MA
N 3
-PH XJV80PT 0,60 0,8 2,2 1,5 - - 40 33 30 24 20 15 - 440,00 505 218 420 46 1"¼ 1" 12
XJV100PT 0,75 1 3 1,9 - - 47 40 35 30 25 20 5 448,00 535 218 420 46 1"¼ 1" 12,5
XJV120PT 0,90 1,2 3,6 2,3 - - 51 45 40 34 30 24 8 454,00 535 218 420 46 1"¼ 1" 13,5
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAJV80P 0,60 0,8 - - 4,5 16 40 33 30 24 20 15 - 489,00 505 218 420 46 1"¼ 1" 12
XAJV100P 0,75 1 - - 5,3 16 47 40 35 30 25 20 5 494,00 535 218 420 46 1"¼ 1" 12,5
XAJV120P 0,90 1,2 - - 5,9 18 51 45 40 34 30 24 8 513,00 535 218 420 46 1"¼ 1" 13,5AU
TO 1
-PH
Technopolymer check valve with flow control disc and spring in AISI 316 assembled.
DNA
H1
DNM
A H
N
Self-priming Jet centrifugal pump with electronic system
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Technopolymer impeller
Motor body with delivery mouth
Technopolymer check valve assembled
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
19
12010080
Technopolymer motor support
XAJV P
Curves and performance η = 2900 1/min
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
XAMO BHorizontal multistage pump with electronic system
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
20
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAMO80B 0,60 0,8 - - 5,15 16 3 33 28 23 20 18 13 10 7 511,00 447 200 226 163 136 1"¼ 1" 14,5
XAMO100B 0,75 1 - - 6,0 18 4 42 35 30 28 24 18 15 10 536,00 477 200 226 163 136 1"¼ 1" 15
XAMO120B 0,90 1,2 - - 7,2 20 5 52 43 40 35 30 25 20 15 561,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
XMO80B 0,60 0,8 - - 5,15 16 3 33 28 23 20 18 13 10 7 456,00 447 200 226 163 136 1"¼ 1" 14,5
XMO100B 0,75 1 - - 6,0 18 4 42 35 30 28 24 18 15 10 477,00 477 200 226 163 136 1"¼ 1" 15
XMO120B 0,90 1,2 - - 7,2 20 5 52 43 40 35 30 25 20 15 504,00 477 200 226 163 136 1"¼ 1" 16MA
N 1
-PH
XMO80BT 0,60 0,8 2,4 1,6 - - 3 33 28 23 20 18 13 10 7 459,00 447 200 226 163 136 1"¼ 1" 14,5
XMO100BT 0,75 1 3 2 - - 4 42 35 30 28 24 18 15 10 482,00 477 200 226 163 136 1"¼ 1" 15
XMO120BT 0,90 1,2 3,3 2,5 - - 5 52 43 40 35 30 25 20 15 506,00 477 200 226 163 136 1"¼ 1" 16MA
N 3
-PH
DNM
DN
A H1 H
A N
N1
Horizontal multistage pump with electronic system
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Impeller Stainless steel AISI 304
Cable fixing handle
Motor body with delivery mouth
21
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
80
120
100
80
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
12010080
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Technopolymer motor support
XAMO B
Curves and performance η = 2900 1/min
XAMOHorizontal multistage pump with electronic system
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
22
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAMO80 0,60 0,8 - - 5,15 16 3 33 28 23 20 18 13 10 7 686,00 447 200 226 163 136 1"¼ 1" 15,5
XAMO100 0,75 1 - - 6,0 18 4 42 35 30 28 24 18 15 10 704,00 477 200 226 163 136 1"¼ 1" 16
XAMO120 0,90 1,2 - - 7,2 20 5 52 43 40 35 30 25 20 15 736,00 477 200 226 163 136 1"¼ 1" 17AU
TO 1
-PH
XMO80T 0,60 0,8 2,4 1,6 - - 3 33 28 23 20 18 13 10 7 628,00 447 200 226 163 136 1"¼ 1" 15,5
XMO100T 0,75 1 3 2 - - 4 42 35 30 28 24 18 15 10 640,00 477 200 226 163 136 1"¼ 1" 16
XMO120T 0,90 1,2 3,3 2,5 - - 5 52 43 40 35 30 25 20 15 686,00 477 200 226 163 136 1"¼ 1" 17MA
N 3
-PH
XMO80 0,60 0,8 - - 5,15 16 3 33 28 23 20 18 13 10 7 629,00 447 200 226 163 136 1"¼ 1" 15,5
XMO100 0,75 1 - - 6,0 18 4 42 35 30 28 24 18 15 10 645,00 477 200 226 163 136 1"¼ 1" 16
XMO120 0,90 1,2 - - 7,2 20 5 52 43 40 35 30 25 20 15 648,00 477 200 226 163 136 1"¼ 1" 17MA
N 1
-PH
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
Horizontal multistage pump with electronic system
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Front basis
Motor body with delivery mouth
23
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
80
120
100
80
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
12010080
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Brass motor support
XAMO
Curves and performance η = 2900 1/min
XAMO HF HIGH-FLOW
Horizontal multistage pump with electronic system HIGH-FLOW
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange / Brass flange for 2HP pump• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene / Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
24
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 50 70 100 120 145A H1 H N N1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAMO1204BHF 0,90 1,2 - - 6,4 25 4 43 38 34 30 24 16 6 648,00 560 165 226 200 136 1"¼ 1”¼ 19,5
XAMO1505BHF 1,10 1,5 - - 7,3 30 5 51 46 43 38 30 21 9 732,00 715 165 226 200 136 1"¼ 1”¼ 21,5
XAMO2006HF 1,50 2,0 - - 10,1 40 6 62 55 51 45 34 24 10 909,00 715 165 226 200 136 1"¼ 1”¼ 23AU
TO 1
-PH
MA
N 3
-PH XMO1204BTHF 0,90 1,2 3,1 2,2 - - 4 43 38 34 30 24 16 6 647,00 560 165 226 200 136 1"¼ 1”¼ 19,5
XMO1505BTHF 1,10 1,5 3,5 2,5 - - 5 51 46 43 38 30 21 9 714,00 715 165 226 200 136 1"¼ 1”¼ 21,5
XMO2006THF 1,50 2,0 4,2 3,0 - - 6 62 55 51 45 34 24 10 854,00 715 165 226 200 136 1"¼ 1”¼ 23
MA
N 1
-PH XMO1204BHF 0,90 1,2 - - 6,4 25 4 43 38 34 30 24 16 6 594,00 560 165 226 200 136 1"¼ 1”¼ 19,5
XMO1505BHF 1,10 1,5 - - 7,3 30 5 51 46 43 38 30 21 9 665,00 715 165 226 200 136 1"¼ 1”¼ 21,5
XMO2006HF 1,50 2,0 - - 10,1 40 6 62 55 51 45 34 24 10 840,00 715 165 226 200 136 1"¼ 1”¼ 23
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
Horizontal multistage pump with electronic system HIGH-FLOW
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Front basis
25
2006 1505 1204
0 20 40 60 80 100 120 140 1600
20
40
60
80
100
200615051204
η %
Efficiency
l/min
0 20 40 60 80 100 120 140 16000
500
1000
1500
2000
2500
Wat
t
Power
l/min
Apartments
Code n° meters
XAMO1204BHF 6 - 8 4
XAMO1505BHF 6 - 8 8
XAMO2006HF 6 - 8 11
Technopolymer motor support until 1,5HP version
2006
1505
1204
XAMO HF
Brass motor support for 2HP version
Curves and performance η = 2900 1/min
Technopolymer impeller
XAMOV BVertical multistage pump with electronic system
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
26
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 DNM DNAkW Hp 230 V Total Hm in CA
XAMOV100B 0,75 1 6,0 18 4 42 35 34 30 28 24 18 15 546,00 545 218 420 46 1"¼ 1” 13
XAMOV120B 0,9 1,2 7,2 20 5 52 43 43 40 35 30 25 20 588,00 545 218 420 46 1"¼ 1” 14AU
TO 1
-PH
DNA
H1
DNM
A
H
N
Vertical multistage pump with electronic system
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Flow sensor Woltmann
Coupling flange
27
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
120
100
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Technopolymer check valve assembled
XAMOV B
Technopolymer motor support
Curves and performance η = 2900 1/min
XAMV BVertical multistage pump with electronic system
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
28
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equi-pment in automatic version)
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAMV100B 0,75 1 - - 6 18 4 42 35 30 28 24 18 15 10 707,00 570 210 394 90 112 1"¼ 1" 13,5
XAMV120B 0,90 1,2 - - 7,2 20 5 52 43 40 35 30 25 20 15 733,00 570 210 394 90 116 1"¼ 1" 15AU
TO 1
-PH
XMV80B 0,60 0,8 - - 4,5 16 3 33 28 23 20 18 13 10 7 594,00 570 210 394 90 112 1"¼ 1" 13,5
XMV100B 0,75 1 - - 6 16 4 42 35 30 28 24 18 15 10 622,00 570 210 394 90 112 1"¼ 1" 14
XMV120B 0,90 1,2 - - 7,2 18 5 52 43 40 35 30 25 20 15 647,00 570 210 394 90 116 1"¼ 1" 15MA
N 1
-PH
XMV80BT 0,60 0,8 2,2 1,5 - - 3 33 28 23 20 18 13 10 7 599,00 570 210 394 90 112 1"¼ 1" 13,5
XMV100BT 0,75 1 3 2 - - 4 42 35 30 28 24 18 15 10 625,00 570 210 394 90 112 1"¼ 1" 14
XMV120BT 0,90 1,2 3,6 2,5 - - 5 52 43 40 35 30 25 20 15 650,00 570 210 394 90 116 1"¼ 1" 15MA
N 3
-PH
NN1
A
HH
1
DN
AD
NM
XAMV B
Vertical multistage pump with electronic system
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Flow sensor Woltmann
Coupling flange
29
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
80
120
100
80
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
12010080
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Technopolymer motor support
Curves and performance η = 2900 1/min
XAMVVertical multistage pump with electronic system
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange / Brass flange for 2HP pump• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene / Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
30
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAMV100 0,75 1 - - 6,0 18 4 42 35 30 28 24 18 15 10 846,00 570 210 394 90 112 1"¼ 1"¼ 17
XAMV120 0,90 1,2 - - 7,2 20 5 52 43 40 35 30 25 20 15 874,00 570 210 394 90 116 1"¼ 1"¼ 18
XAMV150 1,10 1,5 - - 8,4 20 6 63 48 45 41 36 31 25 12 896,00 570 210 394 90 116 1"¼ 1"¼ 19AU
TO 1
-PH
MA
N 1
-PH
MA
N 3
-PH
XMV80 0,60 0,8 - - 5,15 16 3 33 28 23 20 18 13 10 7 751,00 570 210 394 90 112 1"¼ 1"¼ 16,5
XMV100 0,75 1 - - 6,0 18 4 42 35 30 28 24 18 15 10 770,00 570 210 394 90 112 1"¼ 1"¼ 17
XMV120 0,90 1,2 - - 7,2 20 5 52 43 40 35 30 25 20 15 803,00 570 210 394 90 116 1"¼ 1"¼ 18
XMV150 1,10 1,5 - - 8,4 20 6 63 48 45 41 36 31 25 12 822,00 570 210 394 90 116 1"¼ 1"¼ 19
XMV80T 0,60 0,8 2,4 1,6 - - 3 33 28 23 20 18 13 10 7 750,00 570 210 394 90 112 1"¼ 1"¼ 16,5
XMV100T 0,75 1 3 2 - - 4 42 35 30 28 24 18 15 10 776,00 570 210 394 90 112 1"¼ 1"¼ 17
XMV120T 0,90 1,2 3,3 2,5 - - 5 52 43 40 35 30 25 20 15 810,00 570 210 394 90 116 1"¼ 1"¼ 18
XMV150T 1,10 1,5 3,6 2,7 - - 6 63 48 45 41 36 31 25 12 831,00 570 210 394 90 116 1"¼ 1"¼ 19
NN1
A
HH
1
DN
AD
NM
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equi-pment in automatic version)
Vertical multistage pump with electronic system
Flow sensor Woltmann
Coupling flange
31
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
210
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50
60
500
600
700
400
300
200
100
40
70
150120
10080
10
20
30
40
50
60
15012010080
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
150
120
100
80
600
800
1000
1200
1400
1600
1800
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Brass motor support
XAMV
Curves and performance η = 2900 1/min
XAMV HF HIGH-FLOW
Vertical multistage pump with electronic system HIGH-FLOW Description
Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange / Brass flange for 2HP pump• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene / Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
32
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equi-pment in automatic version)
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 50 70 100 120 145A H1 H N DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
XAMV1204BHF 0,90 1,2 - - 6,4 25 4 43 38 34 30 24 16 6 696,00 560 95 226 200 1"¼ 1"¼ 19,5
XAMV1505BHF 1,10 1,5 - - 7,3 30 5 51 46 43 38 30 21 9 779,00 715 95 226 200 1"¼ 1"¼ 21,5
XAMV2006HF 1,50 2,0 - - 10,1 40 6 62 55 51 45 34 24 10 963,00 715 95 226 200 1"¼ 1"¼ 23AU
TO 1
-PH
XMV1204BHF 0,90 1,2 - - 6,4 25 4 43 38 34 30 24 16 6 640,00 560 95 226 200 1"¼ 1"¼ 19,5
XMV1505BHF 1,10 1,5 - - 7,3 30 5 51 46 43 38 30 21 9 709,00 715 95 226 200 1"¼ 1"¼ 21,5
XMV2006HF 1,50 2,0 - - 10,1 40 6 62 55 51 45 34 24 10 894,00 715 95 226 200 1"¼ 1"¼ 23
XMV1204BTHF 0,90 1,2 3,1 2,2 - - 4 43 38 34 30 24 16 6 646,00 560 95 226 200 1"¼ 1"¼ 19,5
XMV1505BTHF 1,10 1,5 3,5 2,5 - - 5 51 46 43 38 30 21 9 713,00 715 95 226 200 1"¼ 1"¼ 21,5
XMV2006THF 1,50 2,0 4,2 3,0 - - 6 62 55 51 45 34 24 10 899,00 715 95 226 200 1"¼ 1"¼ 23
MA
N 1
-PH
MA
N 3
-PH
NN1
A
HH
1
DN
AD
NM
Vertical multistage pump with electronic system HIGH-FLOW
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Flow sensor Woltmann
33
Technopolymer motor support
Apartments
Code n° meters
XAMV1204BHF 6 - 8 4
XAMV1505BHF 6 - 8 8
XAMV2006HF 6 - 8 11
200 150
120
0 20 40 60 80 100 120 140 1600
20
40
60
80
100
200150120
η %
Efficiency
l/min
0 20 40 60 80 100 120 140 16000
500
1000
1500
2000
2500
Wat
t
Power
l/min
200
150
120
XAMV HF
Technopolymer motor support until 1,5HP version
Brass motor support for 2HP version
Curves and performance η = 2900 1/min
XMF BMultistage pump for fountains
DescriptionPump in Stainless Steel with a body with filter for fountains and water plays.
Applications• Fountains and water plays• Cascades for gardens• Oxygenation of water for fishing breeding• Protection rating IP 68 Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 m
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser and impellers (High Flow): Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
34
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H N1 DNMkW Hp 230 V 400 V 230 V Total Hm in CA
XMF80B 0,60 0,8 - - 5,15 16 3 33 28 23 20 18 13 10 7 590,00 557 210 394 136 1"¼ 14,5
XMF100B 0,75 1 - - 6,0 18 4 42 35 30 28 24 18 15 10 618,00 557 210 394 136 1"¼ 15
XMF120B 0,90 1,2 - - 7,2 20 5 52 43 40 35 30 25 20 15 645,00 557 210 394 136 1"¼ 16
XMF150B 1,1 1,5 - - 7,6 20 6 63 47 45 43 36 30 25 17 792,00 557 210 394 136 1"¼ 17
MA
N 1
-PH
XMF80BT 0,60 0,8 2,4 1,6 - - 3 33 28 23 20 18 13 10 7 593,00 557 210 394 136 1"¼ 14,5
XMF100BT 0,75 1 3 2 - - 4 42 35 30 28 24 18 15 10 621,00 557 210 394 136 1"¼ 15
XMF120BT 0,90 1,2 3,3 2,5 - - 5 52 43 40 35 30 25 20 15 647,00 557 210 394 136 1"¼ 16
XMF150BT 1,1 1,5 3,6 2,7 - - 6 63 47 45 43 36 30 25 17 796,00 557 210 394 136 1"¼ 17
MA
N 3
-PH
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 50 70 100 120 145A N H N1 DNMkW Hp 230 V 400 V 230 V Total Hm in CA
XMF1204BHF 0,90 1,2 - - 6,4 20 4 43 38 34 30 24 16 6 640,00 557 210 394 136 1"¼ 16
XMF1505BHF 1,10 1,5 - - 7,3 25 5 51 46 43 38 30 21 9 709,00 557 210 394 136 1"¼ 17
XMF2006HF 1,50 2,0 - - 10,1 30 6 62 55 51 45 34 24 10 893,00 557 210 394 136 1"¼ 19MA
N 1
-PH
XMF1204BTHF 0,90 1,2 3,1 2,2 - - 4 43 38 34 30 24 16 6 646,00 557 210 394 136 1"¼ 16
XMF1505BTHF 1,10 1,5 3,5 2,5 - - 5 51 46 43 38 30 21 9 713,00 557 210 394 136 1"¼ 17
XMF2006THF 1,50 2,0 4,2 3,0 - - 6 62 55 51 45 34 24 10 899,00 557 210 394 136 1"¼ 19MA
N 3
-PH
DNM
A
N
N1
H
LOW
FLO
WH
IGH
FLO
W
Multistage pump for fountains
Applications• Fountains and water plays• Cascades for gardens• Oxygenation of water for fishing breeding• Protection rating IP 68 Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 m
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser and impellers (High Flow): Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
Impeller Stainless steel AISI 304 (LOW FLOW pumps)
Ringbolt
Motor body with delivery mouth
35
Technopolymer motor support
Curves and performance η = 2900 1/min
XMF B
0 20 40 60 80 100 120 140 160
0 20 40 60 80 100 120 140 160
0 1,2 2,4 3,6 4,8 6 7,2 8,4 9,6
0
20
40
60
80
100
60
70
600
50500
40400
30300
20200
10100
040
200615051204
1204
1505
2006
η %
Efficiency
l/min
0 20 40 60 80 100 120 140 16000
500
1000
1500
2000
2500
Wat
t
Power
l/min
2006
1505
1204
15012010080
150
120
10080
15012010080
Technopolymer impeller (HIGH FLOW pumps)
XMN BSingle impeller centrifugal pump
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running pro-tectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 m
Materials• Motor body and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser and impeller: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
36
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 20 40 6 80 100A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XMN80B 0,60 0,8 4,8 16 21 16 14 15 8 3 345,00 396 200 226 163 136 1"¼ 1" 12MA
N 1
-PH
Code
P2Nom.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 20 40 6 80 100A N H H1 N1 DNM DNAkW Hp 230 V 400 V Total Hm in CA
XMN80BT 0,60 0,8 2,4 1,6 21 16 14 15 8 3 348,00 396 200 226 163 136 1"¼ 1" 12MA
N 3
-PH
DNM
DN
A H1 H
A N
N1
Single impeller centrifugal pump
Applications• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 m
Materials• Motor body and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser and impeller: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
Front foot
Motor body with delivery mouth
37
Technopolymer impeller
η %
Efficiency
l/min
0 2010 30 40 50 60 70 80 90 1000
10
20
30
40
50
60
0 2010 30 40 50 60 70 80 90 100400
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
Technopolymer motor support
Curves and performance η = 2900 1/min
XMN B
XMNSingle impeller centrifugal pump
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Medium sprinkling and surface irrigations• Tank drainage and transfersPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 m
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser and impeller: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
38
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 20 40 6 80 100A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XMN80 0,60 0,8 4,8 16 21 16 14 15 8 3 535,00 396 200 226 163 136 1"¼ 1" 12MA
N 1
-PH
Code
P2Nom.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 20 40 6 80 100A N H H1 N1 DNM DNAkW Hp 230 V 400 V Total Hm in CA
XMN80T 0,60 0,8 2,4 1,6 21 16 14 15 8 3 538,00 396 200 226 163 136 1"¼ 1" 12MA
N 3
-PH
DNM
DN
A H1 H
A N
N1
XMN
Single impeller centrifugal pump
Applications• Medium sprinkling and surface irrigations• Tank drainage and transfersPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 m
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser and impeller: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
Cable gland
Motor body with delivery mouth
39
Technopolymer impeller
η %
Efficiency
l/min
0 2010 30 40 50 60 70 80 90 1000
10
20
30
40
50
60
0 2010 30 40 50 60 70 80 90 100400
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
Brass motor support
Curves and performance η = 2900 1/min
XAJE B FLOSelf-priming Jet centrifugal pump with electronic system and float switch
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
40
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAJE80BFLO 0,60 0,8 4,5 16 40 33 30 24 20 15 - 535,00 447 200 226 163 136 1"¼ 1" 14,5
XAJE100BFLO 0,75 1 5,3 16 47 40 35 30 25 20 5 537,00 477 200 226 163 136 1"¼ 1" 15
XAJE120BFLO 0,90 1,2 5,9 18 51 45 40 34 30 24 8 540,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
ON-OFFA U T O
Power cable measures
2 mt
8 m
t
Tank installation
Power
Custom safety height
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
Self-priming Jet centrifugal pump with electronic system and float switch
Materials• Motor body and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Technopolymer impeller
Float switch
Motor body with delivery mouth
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
41
12010080
Technopolymer motor support
XAJE B FLO
Curves and performance η = 2900 1/min
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
XAJE FLO
42
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAJE80FLO 0,60 0,8 4,5 16 40 33 30 24 20 15 - 697,00 447 200 226 163 136 1"¼ 1" 14,5
XAJE100FLO 0,75 1 5,3 16 47 40 35 30 25 20 5 734,00 477 200 226 163 136 1"¼ 1" 15
XAJE120FLO 0,90 1,2 5,9 18 51 45 40 34 30 24 8 738,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
Self-priming Jet centrifugal pump with electronic system and float switch
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
ON-OFFA U T O
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
Power cable measures
2 mt
8 m
t
Tank installation
Power
Custom safety height
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivity Protection rating IP 68
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
43
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
12010080
XAJE FLO
Technopolymer impeller
Front basis
Motor body with delivery mouth
Brass motor support
Curves and performance η = 2900 1/min
XAJV P FLOSelf-priming Jet centrifugal pump with electronic system and float switch
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
44
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 DNM DNAkW Hp 230 V Total Hm in CA
XAJV80PFLO 0,60 0,8 4,5 16 40 33 30 24 20 15 - 587,00 505 218 420 46 1"¼ 1" 12
XAJV100PFLO 0,75 1 5,3 16 47 40 35 30 25 20 5 593,00 535 218 420 46 1"¼ 1" 12,5
XAJV120PFLO 0,90 1,2 5,9 18 51 45 40 34 30 24 8 612,00 535 218 420 46 1"¼ 1" 13,5AU
TO 1
-PH
ON-OFFA U T O
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body: Stainless steel AISI 304• Technopolymer flange and pump body• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Power cable measures
2 mt
8 m
t
Tank installation
Power
Custom safety height
DNA
H1
DNM
A
H
N
Technopolymer check valve with flow control disc and spring in AISI 316 assembled.
Self-priming Jet centrifugal pump with electronic system and float switch
Technopolymer impeller
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
45
12010080
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Technopolymer motor support
Technopolymer check valve assembled
XAJV P FLO
Float switch
Curves and performance η = 2900 1/min
XAMO B FLOHorizontal multistage pump with electronic system and float switch
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
46
ON-OFFA U T O
Power cable measures
2 mt
8 m
t
Tank installation
Power
Custom safety height
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAMO80BFLO 0,60 0,8 5,15 16 3 33 28 23 20 18 13 10 7 605,00 447 200 226 163 136 1"¼ 1" 14,5
XAMO100BFLO 0,75 1 6,0 18 4 42 35 30 28 24 18 15 10 633,00 477 200 226 163 136 1"¼ 1" 15
XAMO120BFLO 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 657,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 assembled
Horizontal multistage pump with electronic system and float switch
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Cable fixing handle
47
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
80
120
100
80
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
12010080
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Technopolymer motor support
XAMO B FLO
Float switch
Curves and performance η = 2900 1/min
XAMO FLO
48
Horizontal multistage pump with electronic system and float switch ON-OFF
A U T O
Power cable measures
2 mt
8 m
t
Tank installation
Power
Custom safety height
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAMO80FLO 0,60 0,8 5,15 16 3 33 28 23 20 18 13 10 7 801,00 447 200 226 163 136 1"¼ 1" 15,5
XAMO100FLO 0,75 1 6,0 18 4 42 35 30 28 24 18 15 10 822,00 477 200 226 163 136 1"¼ 1" 16
XAMO120FLO 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 833,00 477 200 226 163 136 1"¼ 1" 17AU
TO 1
-PH
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
XAMO FLO
Front basis
49
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
80
120
100
80
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
12010080
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Brass motor support
Float switch
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Curves and performance η = 2900 1/min
XAMV B FLOVertical multistage pump with electronic systemand float switch
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Float switch with double insulation• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
50
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAMV100BFLO 0,75 1 6 18 4 42 35 30 28 24 18 15 10 804,00 570 210 394 90 112 1"¼ 1" 14
XAMV120BFLO 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 829,00 570 210 394 90 116 1"¼ 1" 15AU
TO 1
-PH
ON-OFFA U T O
Tank installation Power cable measures
1 mt
8 m
t
Power
Custom safety height
NN1
A
HH
1
DN
AD
NM
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Vertical multistage pump with electronic systemand float switch
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Coupling flange
51
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
120
100
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Technopolymer motor support
XAMV B FLO
Float switch
Curves and performance η = 2900 1/min
XAJE P CE
External capacitor box
52
EXTCAPACITOR
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body: Stainless steel AISI 304• Technopolymer flange and pump body• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensionis mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAJE80PCE 0,60 0,8 4,5 16 40 33 30 24 20 15 - 463,00 447 204 226 163 136 1"¼ 1" 11,5
XAJE100PCE 0,75 1 5,3 16 47 40 35 30 25 20 5 466,00 477 204 226 163 136 1"¼ 1" 12
XAJE120PCE 0,90 1,2 5,9 18 51 45 40 34 30 24 8 473,00 477 204 226 163 136 1"¼ 1" 13AU
TO 1
-PH
Self-priming Jet centrifugal pump with electronic system and external capacitor
1 mt
9 m
t
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)External capacitor box
DNM
DN
A H1 H
A N
N1
XAJE P CE
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
Technopolymer impeller
Cable fixing handle
Motor body with delivery mouth
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
53
12010080
Technopolymer motor support
Curves and performance η = 2900 1/min
XAJE B CESelf-priming Jet centrifugal pump with electronic system and external capacitor
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body and pump body: Stainless steel AISI 304• Technopolymer flange• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
54
EXTCAPACITOR
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAJE80BCE 0,60 0,8 4,5 16 40 33 30 24 20 15 - 493,00 447 200 226 163 136 1"¼ 1" 11,5
XAJE100BCE 0,75 1 5,3 16 47 40 35 30 25 20 5 497,00 477 200 226 163 136 1"¼ 1" 12
XAJE120BCE 0,90 1,2 5,9 18 51 45 40 34 30 24 8 499,00 477 200 226 163 136 1"¼ 1" 13AU
TO 1
-PH
1 mt
9 m
t
DNM
DN
A H1 H
A N
N1
External capacitor box
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
Self-priming Jet centrifugal pump with electronic system and external capacitor
Materials• Motor body and pump body: Stainless steel AISI 304• Technopolymer flange• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
Technopolymer impeller
Capacitor box
Motor body with delivery mouth
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
55
12010080
XAJE B CE
Technopolymer motor support
Curves and performance η = 2900 1/min
XAJE CE
56
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
Self-priming Jet centrifugal pump with electronic system and external capacitor
EXTCAPACITOR
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAJE80CE 0,60 0,8 4,5 16 40 33 30 24 20 15 - 658,00 447 200 226 163 136 1"¼ 1" 14,5
XAJE100CE 0,75 1 5,3 16 47 40 35 30 25 20 5 692,00 477 200 226 163 136 1"¼ 1" 15
XAJE120CE 0,90 1,2 5,9 18 51 45 40 34 30 24 8 699,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
1 mt
9 m
t
DNM
DN
A H1 H
A NN1
External capacitor box
Technopolymer check valve with flow control disc and spring in AIS I316 (standard equipment in automatic version)
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
57
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
12010080
XAJE CE
Capacitor box
Technopolymer impeller
Front basis
Brass motor support
Curves and performance η = 2900 1/min
XAJV P CESelf-priming Jet centrifugal pump with electronic system and external capacitor
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
58
EXTCAPACITOR
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 DNM DNAkW Hp 230 V Total Hm in CA
XAJV80PCE 0,60 0,8 4,5 16 40 33 30 24 20 15 - 547,00 505 218 420 46 1"¼ 1" 12
XAJV100PCE 0,75 1 5,3 16 47 40 35 30 25 20 5 552,00 535 218 420 46 1"¼ 1" 12,5
XAJV120PCE 0,90 1,2 5,9 18 51 45 40 34 30 24 8 570,00 535 218 420 46 1"¼ 1" 13,5AU
TO 1
-PH
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body: Stainless steel AISI 304• Technopolymer flange and pump body• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
1 mt
9 m
t
DNA
H1
DNM
A H
N
External capacitor box
Technopolymer check valve with flow control disc and spring in AISI 316 assembled.
Self-priming Jet centrifugal pump with electronic system and external capacitor
Technopolymer impeller
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
59
12010080Applications
• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Technopolymer motor support
Technopolymer check valve assembled
XAJV P CE
Capacitor box
Curves and performance η = 2900 1/min
XAMO B CEHorizontal multistage pump with electronic system and external capacitor
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
60
EXTCAPACITOR
1 mt
9 m
t
Technopolymer check valve with flow control disc and spring in AISI 316 assembled
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAMO80BCE 0,60 0,8 5,15 16 3 33 28 23 20 18 13 10 7 567,00 447 200 226 163 136 1"¼ 1" 14,5
XAMO100BCE 0,75 1 6,0 18 4 42 35 30 28 24 18 15 10 593,00 477 200 226 163 136 1"¼ 1" 15
XAMO120BCE 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 617,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
DNM
DN
A H1 H
A N
N1
External box capacitor
Horizontal multistage pump with electronic system and external capacitor
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
Cable fixing handle
61
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
80
120
100
80
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
12010080
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Technopolymer motor support
XAMO B CE
Capacitor box
Curves and performance η = 2900 1/min
XAMO CE
62
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Horizontal multistage pump with electronic system and external capacitor
EXTCAPACITOR
1 mt
9 m
tApplications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Brass flange• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive • External capacitor box: protection rating IP55• Class F insulated motors
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAMO80CE 0,60 0,8 4,5 16 3 33 28 23 20 18 13 10 7 744,00 447 200 226 163 136 1"¼ 1" 15,5
XAMO100CE 0,75 1 5,3 16 4 42 35 30 28 24 18 15 10 762,00 477 200 226 163 136 1"¼ 1" 16
XAMO120CE 0,90 1,2 5,9 18 5 52 43 40 35 30 25 20 15 794,00 477 200 226 163 136 1"¼ 1" 17AU
TO 1
-PH
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
External capacitor box
XAMO CE
Front basis
63
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
80
120
100
80
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
12010080
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Brass motor support
Capacitor box
Curves and performance η = 2900 1/min
XAMOV B CEVertical multistage pump with electronic system and external capacitor Description
Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
64
EXTCAPACITOR
1 mt
9 m
t
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 DNM DNAkW Hp 230 V Total Hm in CA
XAMOV100BCE 0,75 1 6,0 18 4 42 35 34 30 28 24 18 15 642,00 545 218 420 46 1"¼ 1” 13
XAMOV120BCE 0,9 1,2 7,2 20 5 52 43 43 40 35 30 25 20 682,00 545 218 420 46 1"¼ 1” 14AU
TO 1
-PH
DNA
H1
DNM
A
H
N
External capacitor box
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
65
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
120
100
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
XAMOV B CE
Coupling flange
Impeller Stainless steel AISI 304
Technopolymer check valve assembled
Technopolymer motor support
Capacitor box
Curves and performance η = 2900 1/min
XAMV B CE
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
66
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAMV100BCE 0,75 1 6 18 4 42 35 30 28 24 18 15 10 764,00 570 210 394 90 112 1"¼ 1"¼ 14
XAMV120BCE 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 789,00 570 210 394 90 116 1"¼ 1"¼ 15AU
TO 1
-PH
Vertical multistage pump with electronic system and external capacitor
EXTCAPACITOR
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
NN1
A
HH
1
DN
AD
NM
External capacitor box
1 mt
9 m
t
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Coupling flange
67
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
120
100
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Technopolymer motor support
XAMV B CE
Capacitor box
Curves and performance η = 2900 1/min
XAMV CE
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP68
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange• Shaft: Stainless steel AISIi 420• Diffuser: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 9 m length pump/box• H07RN8-F Electric cable 1 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• External capacitor box: protection rating IP55• Class F insulated motors
68
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XAMV100CE 0,75 1 6,0 18 4 42 35 30 28 24 18 15 10 903,00 570 210 394 90 112 1"¼ 1"¼ 17
XAMV120CE 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 931,00 570 210 394 90 116 1"¼ 1"¼ 18
XAMV150CE 1,10 1,5 8,4 20 6 63 48 45 41 36 31 25 12 951,00 570 210 394 90 116 1"¼ 1"¼ 19AU
TO 1
-PH
Vertical multistage pump with electronic system and external capacitor
EXTCAPACITOR
External capacitor box
1 mt
9 m
t
NN1
A
HH
1
DN
AD
NM
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Coupling flange
69
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
210
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50
60
500
600
700
400
300
200
100
40
70
150120
100
10
20
30
40
50
60
150120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
150
120
100
600
800
1000
1200
1400
1600
1800
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Brass motor support
XAMV CE
Capacitor box
Curves and performance η = 2900 1/min
XSSJE BSelf-priming Jet centrifugal pump with electronic system with start and stop ramp
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
70
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensionis mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XSSJE80B 0,60 0,8 4,5 16 40 33 30 24 20 15 - 554,00 447 200 226 163 136 1"¼ 1" 14,5
XSSJE100B 0,75 1 5,3 16 47 40 35 30 25 20 5 558,00 477 200 226 163 136 1"¼ 1" 15
XSSJE120B 0,90 1,2 5,9 18 51 45 40 34 30 24 8 561,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
SOFT START
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316(standard equipment in automatic version)
XSSJE B
Materials• Motor body and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Technopolymer impeller
Cable fixing handle
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
71
12010080
Electronic control Soft-Start
Technopolymer motor support
Curves and performance η = 2900 1/min
XSSJE
72
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XSSJE80 0,60 0,8 4,5 16 40 33 30 24 20 15 - 718,00 447 200 226 163 136 1"¼ 1" 14,5
XSSJE100 0,75 1 5,3 16 47 40 35 30 25 20 5 754,00 477 200 226 163 136 1"¼ 1" 15
XSSJE120 0,90 1,2 5,9 18 51 45 40 34 30 24 8 758,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
Self-priming Jet centrifugal pump with electronic system with start and stop ramp
SOFT START
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
Technopolymer impeller
Front basis
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
73
Materials• Motor body and pump body: Stainless steel AISI 304• Brass flange • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
12010080
Electronic control Soft-Start
Brass motor support
XSSJE
Curves and performance η = 2900 1/min
XSSJV PSelf-priming Jet centrifugal pump with electronic system with start and stop ramp
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
74
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 DNM DNAkW Hp 230 V Total Hm in CA
XSSJV80P 0,60 0,8 4,5 16 40 33 30 24 20 15 - 606,00 505 218 420 46 1"¼ 1" 12
XSSJV100P 0,75 1 5,3 16 47 40 35 30 25 20 5 613,00 535 218 420 46 1"¼ 1" 12,5
XSSJV120P 0,90 1,2 5,9 18 51 45 40 34 30 24 8 631,00 535 218 420 46 1"¼ 1" 13,5AU
TO 1
-PH
SOFT START
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body: Stainless steel AISI 304• Technopolymer flange and body pump• Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors DNA
H1
DNM
A
H
N
Technopolymer check valve with flow control disc and spring in AISI 316 assembled.
Technopolymer impeller
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
0 10 20 30 40 50 60 700
5
10
15
20
25
12010080η
%
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
120100
80
Wat
t
Power
l/min
75
12010080
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Electronic control Soft-Start
Technopolymer motor support
Technopolymer check valve assembled
XSSJV P
Curves and performance η = 2900 1/min
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XSSMO100B 0,75 1 6,0 18 4 42 35 30 28 24 18 15 10 653,00 477 200 226 163 136 1"¼ 1" 15
XSSMO120B 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 679,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
XSSMO BHorizontal multistage pump with electronic system with start and stop ramp
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
76
SOFT START
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 (standard equipment in automatic version)
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Cable fixing handle
77
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
120
100
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Electronic control Soft-Start
Technopolymer motor support
XSSMO B
Curves and performance η = 2900 1/min
XSSMO
78
Horizontal multistage pump with electronic system with start and stop ramp
SOFT START
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface or under-ground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Brass flange for 2HP pump• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene / Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XSSMO100 0,75 1 6,0 18 4 42 35 30 28 24 18 15 10 822,00 477 200 226 163 136 1"¼ 1" 15
XSSMO120 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 854,00 477 200 226 163 136 1"¼ 1" 16AU
TO 1
-PH
DNM
DN
A H1 H
A N
N1
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Motor body with delivery mouth
79
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
120
100
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Electronic control Soft-Start
Brass motor support
XSSMO
Curves and performance η = 2900 1/min
XSSMO HF HIGH-FLOW
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange / Brass flange for 2HP pump• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene / Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10 m length with Schuko plug• Tropicalized circuit a in compliance with the RoHS directive• Class F insulated motors
80
Horizontal multistage pump with electronic system with start and stop ramp HIGH-FLOW
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface or under-ground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
SOFT START
DNM
DN
A H1 H
A N
N1
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 50 70 100 120 145A H1 H N N1 DNM DNAkW Hp 230 V Total Hm in CA
XSSMO1204BHF 0,90 1,2 6,4 25 4 43 38 34 30 24 16 6 765,00 560 165 226 200 136 1"¼ 1”¼ 19,5
XSSMO1505BHF 1,10 1,5 7,3 30 5 51 46 43 38 30 21 9 849,00 715 165 226 200 136 1"¼ 1”¼ 21,5
XSSMO2006HF 1,50 2,0 10,1 40 6 62 55 51 45 34 24 10 1.026,00 715 165 226 200 136 1"¼ 1”¼ 23AU
TO 1
-PH
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
81
2006 1505 1204
0 20 40 60 80 100 120 140 1600
20
40
60
80
100
200615051204η
%
Efficiency
l/min
0 20 40 60 80 100 120 140 16000
500
1000
1500
2000
2500
Wat
t
Power
l/min
2006
1505
1204
Electronic control Soft-Start
XSSMO HF
Apartments
Code n° meters
XSSMO1204BHF 6 - 8 4
XSSMO1505BHF 6 - 8 8
XSSMO2006HF 6 - 8 11
Technopolymer motor support until 1,5HP version
Brass motor support for 2HP version
Curves and performance η = 2900 1/min
Technopolymer impeller
XSSMOV BVertical multistage pump with electronic system with start and stop ramp
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
82
SOFT START
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 DNM DNAkW Hp 230 V HTotal Hm in CA
XSSMOV100B 0,75 1 6,0 18 4 42 35 34 30 28 24 18 15 664,00 545 218 420 46 1"¼ 1” 13
XSSMOV120B 0,9 1,2 7,2 20 5 52 43 43 40 35 30 25 20 705,00 545 218 420 46 1"¼ 1” 14AU
TO 1
-PH
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
DNA
H1
DNM
A
H
N
83
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
120
100
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Electronic control Soft-Start
Application• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
XSSMOV B
Flow sensor Woltmann
Coupling flange
Impeller Stainless steel AISI 304
Technopolymer motor support
Curves and performance η = 2900 1/min
XSSMV BVertical multistage pump with electronic system with start and stop ramp
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
84
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XSSMV100B 0,75 1 6 18 4 42 35 30 28 24 18 15 10 826,00 570 210 394 90 112 1"¼ 1" 14
XSSMV120B 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 852,00 570 210 394 90 116 1"¼ 1" 15AU
TO 1
-PH
SOFT START
NN1
A
HH
1
DN
AD
NM
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Stainless steel AISI 304• Basis: Inox AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics and oil chamber• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Vertical multistage pump with electronic system with start and stop ramp
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Tank drainage and transfers• Industrial washing and cooling• Systems for water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Flow sensor Woltmann
85
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
120
100
120
100
600
800
1000
1200
1400
1600
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
Electronic control Soft-Start
Technopolymer motor support
XSSMV B
Curves and performance η = 2900 1/min
XSSMV
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface or under-ground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
86
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
XSSMV100 0,75 1 6,0 18 4 42 35 30 28 24 18 15 10 964,00 570 210 394 90 112 1"¼ 1"¼ 17
XSSMV120 0,90 1,2 7,2 20 5 52 43 40 35 30 25 20 15 992,00 570 210 394 90 112 1"¼ 1"¼ 18
XSSMV150 1,10 1,5 8,4 20 6 63 48 45 41 36 31 25 12 1.014,00 570 210 394 90 112 1"¼ 1"¼ 19AU
TO 1
-PH
Vertical multistage pump with electronic system with start and stop ramp
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange / Brass flange for 2HP pump• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene / Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
NN1
A
HH
1
DN
AD
NM
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
SOFT START
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Flow sensor Woltmann
87
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
210
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50
60
500
600
700
400
300
200
100
40
70
150120
100
10
20
30
40
50
60
150120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
150
120
100
600
800
1000
1200
1400
1600
1800
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
Vertical multistage pump with electronic system with start and stop ramp
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatmentPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Brass motor support
Electronic control Soft-Start
XSSMV
Curves and performance η = 2900 1/min
XSSMV HF HIGH-FLOW
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
88
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 50 70 100 120 145A H1 H N DNM DNAkW Hp 230 V Total Hm in CA
XSSMV1204BHF 0,90 1,2 6,4 25 4 43 38 34 30 24 16 6 813,00 560 95 226 200 1"¼ 1"¼ 19,5
XSSMV1505BHF 1,10 1,5 7,3 30 5 51 46 43 38 30 21 9 898,00 715 95 226 200 1"¼ 1"¼ 21,5
XSSMV2006HF 1,50 2,0 10,1 40 6 62 55 51 45 34 24 10 1.081,00 715 95 226 200 1"¼ 1"¼ 23AU
TO 1
-PH
Vertical multistage pump with electronic system with start and stop ramp HIGH-FLOW
SOFT START
DescriptionThe pump with power ramp allows a slow starting and stopping of the motor, in order to avoid water hammer and current peaks with the consequent energy saving.Up/Down technology for submersed, surface or underground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
NN1
A
HH
1
DN
AD
NM
Materials• Motor body, impellers and pump body: Stainless steel AISI 304• Technopolymer flange / Brass flange for 2HP pump• Shaft: Stainless steel AISI 420• Diffuser: Noryl• Rear cap: Polypropilene / Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10 m length with Schuko plug• Tropicalized circuit board in compliance with the RoHS directive• Class F insulated motors
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Applications• Domestic boosting• Medium sprinkling and surface irrigations• Industrial washing and cooling• Systems for potable water treatment
Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
89
Technopolymer motor support
Apartments
Code n° meters
XSSMV1204BHF 6 - 8 4
XSSMV1505BHF 6 - 8 8
XSSMV2006HF 6 - 8 11
200 150
120
0 20 40 60 80 100 120 140 1600
20
40
60
80
100
200150120
η %
Efficiency
l/min
0 20 40 60 80 100 120 140 16000
500
1000
1500
2000
2500
Wat
t
Power
l/min
200
150
120
Vertical multistage pump with electronic system with start and stop ramp HIGH-FLOW
Electronic control Soft-Start
XSSMV HF
Technopolymer motor support until 1,5HP version
Brass motor support for 2HP version
Curves and performance η = 2900 1/min
WP15Self-priming pump with flexible impeller
DescriptionPumping of warm clean water and olive oil Pumping liquids from boilers and aquariums Emptying of oil tank Bilge pump on boats Easily transportable Protection rating IP 54
Applications• Emptying of water heaters and boilers • Emptying of fuel oil tank • Emptying of heating systems with hot water• Transfer of heated fuel oilPumped liquid: water, heated fuel oil, hot water
Materials• Brass pump body• Shaft: Inox AISI 304• Bolts: Inox AISI 304• Gasket: NBR• Electric cable 1,5 m• Class F insulated motors
90
Code
Absorbed powerNom.
1 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 2,5 5 7,5 10 12,5 15A B H DNM DNAW HP 230 V Total Hm in CA
WP15 120 0,16 1,6 12 10 8 6 4 2 0 486,00 230 170 150 3/4" (ø19) 3/4" (ø19) 5
A
H
DNA
B
Hydraulic body
Rubber impeller
O-Ring
O-Ring
Hydraulic closure
Self-priming pump with flexible impeller
Applications• Emptying of water heaters and boilers • Emptying of fuel oil tank • Emptying of heating systems with hot water• Transfer of heated fuel oilPumped liquid: water, heated fuel oil, hot water
Materials• Brass pump body• Shaft: Inox AISI 304• Bolts: Inox AISI 304• Gasket: NBR• Electric cable 1,5 m• Class F insulated motors
Brass pump body with hose holder
Handle
91
Rubber impeller
Curves and performance η = 2900 1/min
WP15
Pumping of warm clean water and olive oil
1 Liquid to be pumped2 Isolation valve3 No return valve4 Pump5 Liquid transferred tank
2
1
3
4
5
52 3
4
Emptying of heating systems with hot water
1 Circulating liquid in the installation2 Isolation valve3 No return valve4 Pump5 Delivery of discharge liquid
1
1
X-MAREPump with flexible impeller
DescriptionUsed on boat for pouring water, either sea water Pumps liquid with impurities Electric motor with thermic protectionBilge pumps Deck washing Protection rating IP 54
Application• Pumping of sea water • Pumping of clean water• Little boats cleaning
Pumped liquid: Fresh water Salt waterKinematic viscosity max. 5 cSt
Materials• Techno-polymer body pump totally Stainless steel AISI 303• Shaft: Stainless steel AISI 303 • Gaskets: NBR rubber • Impeller: NBR nitrile rubber • Electric cable 2 m• Class F insulated motors • Light switch: ON/OFF
92
Code
Absorbed powerNom.
1 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 5 10 15 20 25 30A N N1 H H1 DNM DNAW HP 230 V Total Hm in CA
XMARE 0,290 0,40 1,5 10 9,2 8,6 8,1 7,1 5,5 1 360,00 214 127 120 182 79 1/2" 1/2" 5,5
A N
N1
H1
H
Pump with flexible impeller
Application• Pumping of sea water • Pumping of clean water• Little boats cleaning
Pumped liquid: Fresh water Salt waterKinematic viscosity max. 5 cSt
Materials• Techno-polymer body pump totally Stainless steel AISI 303• Shaft: Stainless steel AISI 303 • Gaskets: NBR rubber • Impeller: NBR nitrile rubber • Electric cable 2 m• Class F insulated motors • Light switch: ON/OFF
Body pump
93
Impeller NBR rubber flexible
Hydraulic room in Stainless Steel
Light switch: ON/OFF
l/min
kW
0,1
0,2
0,3
0,4
Curves and performance η = 2900 1/min
X-MARE
X1AJEElectronic booster set with Stainless Steel tank and self-priming pump
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Industrial installation boostingPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
Materials• Tank: Stainless steel 24 l• Pump body and motor body: Stainless steel AISI 304• Brass flanges • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
94
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
X1AJE80 0,60 0,8 4,5 16 40 30 20 15 - - - 936,00 447 200 226 163 136 1" 1" 22
X1AJE100 0,75 1 5,3 16 47 35 25 20 5 - - 942,00 447 200 226 163 136 1" 1" 22,5
X1AJE120 0,90 1,2 6,3 18 49 40 30 24 8 - - 948,00 447 200 226 163 136 1" 1" 23,5
X1AJE
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Industrial installation boostingPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
Materials• Tank: Stainless steel 24 l• Pump body and motor body: Stainless steel AISI 304• Brass flanges • Shaft: Stainless steel AISI 420• Diffuser, impeller and venturi Jet: Noryl• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
Body pumpe
Stainless Steel tank 24 l
95
0 10 20 30 40 50 60 700
5
10
15
20
25
η %
Efficiency
l/min
0 10 20 30 40 50 60 70600
800
1000
1200
1400
1600
Wat
t
Power
l/min
H tkPa m 0 IMP. gal/min
0 US. gal/min
5
5
10
10
15
15
0 0
30
60
90
120
150
180
Htft
0l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4
10 20 30 40 50 60 70
10
20
30
40
50500
400
300
200
100
40
60
120 100 80
120100 80
Brass support
Curves and performance η = 2900 1/min
Technopolymer impeller
X1AMOElectronic booster set with Stainless Steel tank and multistage pump
96
Code
P2Nom.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 10 20 30 40 50 60A N H H1 N1 DNM DNAkW Hp 230 V Total Hm in CA
X1AMO100 0,75 1 5,3 18 4 42 37 30 28 24 15 - 971,00 447 200 226 163 136 1" 1" 22,5
X1AMO120 0,90 1,2 6,3 20 5 52 46 40 35 30 20 8 991,00 447 200 226 163 136 1" 1" 23,5
DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Tank: Stainless steel 24 l• Pump body and motor body: Stainless steel AISI 304• Brass flanges • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Impeller: Stainless steel AISI 304• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
Technopolymer check valve with flow control disc and spring in AISI 316 standard equipment
Body pump
Stainless Steel tank 24 l
97
Brass support
Impeller Stainless steel AISI 304
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
210
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50
60
500
600
700
400
300
200
100
40
70
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
120
100
600
800
1000
1200
1400
1600
1800
Wat
t
Power
l/min
10 20 30 40 50 60 70 80 90 100 1100
100
120DescriptionUp/Down technology for submersed, surface orunderground installationAutomatic system of water supply; dry-running protectionAntiblocking system every 72 hours of pump inactivityProtection rating IP 68
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CDepth max 5 mCalibrating pressure rate switch 1,5 bar
Materials• Tank: Stainless steel 24 l• Pump body and motor body: Stainless steel AISI 304• Brass flanges • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Impeller: Stainless steel AISI 304• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Dumping feet: rubber• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN8-F Electric cable 10m length with Schuko plug• Class F insulated motors
Curves and performance η = 2900 1/min
X1AMO
X2MO BElectronic booster set with 2 multistage horizontal pumps
DescriptionComputerized system with digital pressure switch for automatic water supply and pump protection against dry- running. Antiblocking system every 72 hours of pump inactivity. Protection rating IP 68
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
Materials• Pump body, impellers and motor body: Stainless steel AISI 304• Technopolymer flanges • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Impeller: Stainless steel AISI 304• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Inlet and outlet manifold: Stainless steel AISI 304• Support base: Stainless steel AISI 304• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• Tropicalized circuit boards in compliance with the RoHS directive• Digital pressure switch• Pressure control manometer• Class F insulated motors
98
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 60 80 100 120 140 160 180A B C H DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
X2MO100B 0,75+0,75 1+1 - - 6+6 18 4 42 35 30 28 24 18 15 10 2.098,00 447 200 620 226 2" 2" 60
X2MO120B 0,90+0,90 1,2+1,2 - - 7,2+7,2 20 5 52 43 40 35 30 25 20 15 2.147,00 447 200 620 226 2" 2" 60
X2MO100BT 0,75+0,75 1+1 3+3 2+2 - - 4 42 35 30 28 24 18 15 10 2.113,00 447 200 620 226 2" 2" 60
X2MO120BT 0,90+0,90 1,2+1,2 3,3+3,3 2,5+2,5 - - 5 52 43 40 35 30 25 20 15 2.159,00 447 200 620 226 2" 2" 603-PH
1-PH
A
C
X2MOB
DescriptionComputerized system with digital pressure switch for automatic water supply and pump protection against dry- running. Antiblocking system every 72 hours of pump inactivity. Protection rating IP 68
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
Materials• Pump body, impellers and motor body: Stainless steel AISI 304• Technopolymer flanges • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Impeller: Stainless steel AISI 304• Rear cap: Stainless steel AISI 304• Basis: Stainless steel AISI 304• Inlet and outlet manifold: Stainless steel AISI 304• Support base: Stainless steel AISI 304• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• Tropicalized circuit boards in compliance with the RoHS directive• Digital pressure switch• Pressure control manometer• Class F insulated motors
Coupling base
99
Impeller Stainless steel AISI 304
Apartments
Code n° Max flow l/min
X2MO100 2 ÷ 3 180
X2MO120 2 ÷ 4 200
X2MO100T 2 ÷ 4 180
X2MO120T 2 ÷ 5 200
10
20
30
40
50
60
120100
η %
Efficiency
l/min
10 20 30 40 50 60 70 80 90 100 1100
l/min
m³/h
500
400
300
200
100
40 0
10
20
30
40
50
60
0
0
40
2,4
80
4,8
120
7,2
160
9,6
200
12
260
15,6
120
100
Curves and performance η = 2900 1/min
120100
120T
100T
0
500
1000
1500
2000
2500
3000
3500
Wat
t
Power
l/min
20 40 60 80 120 140 160 180 2000 100
Technopolymer support
Apartments
Code n° Max flow l/m
X2MV100 2 ÷ 3 180
X2MV120 2 ÷ 4 200
X2MV150 3 ÷ 6 210
X2MV1204BHF 4 ÷ 6 290
X2MV1505BHF 6 ÷ 8 290
X2MV2006HF 8 ÷ 10 300
X2MV X2MVHFElectronic booster set with 2 multistage vertical pumps
100
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 60 100 120 140 180 220 260 290A B C D H DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
X2MV100B 0,75+0,75 1+1 - - 6+6 18 4 42 35 28 24 18 10 - - - 2.205,00 560 130 470 620 650 2" 2" 60
X2MV120B 0,90+0,90 1,2+1,2 - - 7,2+7,2 20 5 52 43 35 30 25 15 - - - 2.242,00 560 130 470 620 650 2" 2" 60
X2MV150 1,1+1,1 1,5+1,5 - - 8,8+8,8 20 6 63 51 42 36 25 18 - - - 2.501,00 560 130 470 620 650 2" 2" 66
X2MV100BT 0,75+0,75 1+1 3+3 2+2 - - 4 42 35 28 24 18 10 - - - 2.215,00 560 130 470 620 650 2" 2" 60
X2MV120BT 0,90+0,90 1,2+1,2 3,3+3,3 2,5+2,5 - - 5 52 43 35 30 25 15 - - - 2.259,00 560 130 470 620 650 2" 2" 60
X2MV150T 1,1+1,1 1,5+1,5 3,6+3,6 2,7+2,7 - - 6 63 51 42 36 25 18 - - - 2.513,00 560 130 470 620 650 2" 2" 66
DescriptionComputerized system with digital pressure switch for automatic water supply and pump protection against dry- running. Antiblocking system every 72 hours of pump inactivity. Protection rating IP 68.
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
Materials• Pump body and motor body: Stainless steel AISI 304• Technopolymer / Brass (only 2HP model) flanges • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Impeller: Stainless steel AISI 304 (low flow) / technopolymer (high flow)• Rear cap: Stainless steel AISI 304 / Techopolymer • Basis: Stainless steel AISI 304• Inlet and outlet manifold: Stainless steel AISI 304• Support base: Stainless steel AISI 304• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• Tropicalized circuit boards in compliance with the RoHS directive• Digital pressure switch• Pressure control manometer• Class F insulated motors
X2MV1204BHF 0,90+0,90 1,2+1,2 3,1+3,1 2,2+2,2 6,4+6,4 25 4 43 38 34 32 30 26 20 13 7 2.515,00 560 150 660 620 790 2" 2" 68
X2MV1505BHF 1,1+1,1 1,5+1,5 3,5+3,5 2,5+2,5 7,3+7,3 30 5 51 46 43 41 38 32 27 18 10 2.675,00 560 150 660 620 790 2" 2" 69
X2MV2006HF 1,5+1,5 2,0+2,0 4,2+4,2 3,0+3,0 10,1+10,1 40 6 62 55 52 48 45 36 30 22 12 3.045,00 560 150 660 620 790 2" 2" 72
X2MV1204BTHF 0,75+0,75 1+1 3+3 2+2 - - 4 43 38 34 32 30 26 20 13 7 2.704,00 560 150 660 620 790 2" 2" 68
X2MV1505BTHF 0,90+0,90 1,2+1,2 3,3+3,3 2,5+2,5 - - 5 51 46 43 41 38 32 27 18 10 2.835,00 560 150 660 620 790 2" 2" 69
X2MV2006THF 1,1+1,1 1,5+1,5 3,6+3,6 2,7+2,7 - - 6 62 55 52 48 45 36 30 22 12 3.166,00 560 150 660 620 790 2" 2" 72
3-PH
3-PH
1-PH
1-PH
LOW
FLO
WH
IGH
FLO
W
D
101
Brass support (2HP)
Impeller Stainless steel AISI 304
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
Materials• Pump body and motor body: Stainless steel AISI 304• Technopolymer / Brass (only 2HP model) flanges • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Impeller: Stainless steel AISI 304 (low flow) / technopolymer (high flow)• Rear cap: Stainless steel AISI 304 / Techopolymer • Basis: Stainless steel AISI 304• Inlet and outlet manifold: Stainless steel AISI 304• Support base: Stainless steel AISI 304• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• Tropicalized circuit boards in compliance with the RoHS directive• Digital pressure switch• Pressure control manometer• Class F insulated motors
Control panel
0
0
040
200
100
300
400
500
600
10
20
30
40
50
60
70
2,4
40
4,8
80
7,2
120
9,6
160
12
200
14,4
240
16,8
280
19,2
320
2006
1505
1204150
120
100
Curves and performance η = 2900 1/min
X2MV X2MVHF
10
20
30
40
50
60
100120150
120415052006
η %
Efficiency
l/min
20 40 60 80 100 120 140 1600
150 2006
1505
1204
120
100
3000
3500
2500
1500
2000
4000
4500
Wat
t
Power
l/min
50 250100 150 200 3000
Technopolymer impeller (high flow pump)
Technopolymer support
X3MV BElectronic booster set with 3 multistage vertical pumps
102
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp. Cap
µF Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 60 80 100 120 140 160 180A B C D H DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
X3MV100B 3x0,75 3x1 - - 3x6 18 4 42 35 30 28 24 18 15 10 on request 760 150 470 930 650 2" 2" 90
X3MV120B 3x0,9 3x1,2 - - 3x7,2 20 5 52 43 40 35 30 25 20 15 on request 760 150 470 930 650 2" 2" 90
X3MV150 3x1,1 3x1,5 - - 3x8,8 20 6 63 51 45 42 36 25 25 18 on request 760 150 470 930 650 2" 2" 102
X3MV100BT 3x0,75 3x1 3x3 3x2 - - 4 42 35 30 28 24 18 15 10 on request 760 150 470 930 650 2" 2" 90
X3MV120BT 3x0,9 3x1,2 3x3,3 3x2,5 - - 5 52 43 40 35 30 25 20 15 on request 760 150 470 930 650 2" 2" 90
X3MV150T 3x1,1 3x1,5 3x3,6 3x2,7 - - 6 63 51 45 42 36 25 25 18 on request 760 150 470 930 650 2" 2" 102
DescriptionComputerized system with digital pressure switch for automatic water supply and pump protection against dry- running. Antiblocking system every 72 hours of pump inactivity. Protection rating IP 68
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
3-PH
1-PH
D
Materials• Pump body and motor body: Stainless steel AISI 304• Technopolymer / Brass (only 1,5 and 2 HP model) flanges • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Impeller: Stainless steel AISI 304• Rear cap: Stainless steel AISI 304 / Techopolymer • Basis: Stainless steel AISI 304• Inlet and outlet manifold: Stainless steel AISI 304• Support base: Stainless steel AISI 304• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• Tropicalized circuit boards in compliance with the RoHS directive• Digital pressure switch• Pressure control manometer• Class F insulated motors
Manometer
103
Brass support (1,5 HP)
Impeller Stainless steel AISI 304
Apartments
Code n° Max flow l/min
X3MV100 2 ÷ 4 270
X3MV120 3 ÷ 6 300
X3MV150 4 ÷ 8 315
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
150
120
100
0
0
040
0100
0200
0300
0400
0500
0600
0
3,6
60
7,2
120
10,8
180
14,4
240
18
300
21,6
360
Curves and performance η = 2900 1/min
X3MV
10
20
30
40
50
60
100120150
η %
Efficiency
l/min
20 40 60 80 100 120 140 1600
150
120
1003000
4000
2000
0
1000
5000
6000
Wat
t
Power
l/min
50 250100 150 200 3000
Technopolymer support
Materials• Pump body and motor body: Stainless steel AISI 304• Technopolymer / Brass (only 1,5 and 2 HP model) flanges • Shaft: Stainless steel AISI 420• Diffuser: Noryl• Impeller: Stainless steel AISI 304• Rear cap: Stainless steel AISI 304 / Techopolymer • Basis: Stainless steel AISI 304• Inlet and outlet manifold: Stainless steel AISI 304• Support base: Stainless steel AISI 304• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• Tropicalized circuit boards in compliance with the RoHS directive• Digital pressure switch• Pressure control manometer• Class F insulated motors
X1MOI BMultistage pump with electronic system and inverter
104
DescriptionUp/Down technology for submersed, surface or underground installation.For submerged and underground installation, the inverter control must be disconnected to place it in a protected area from moisture.The automatic system with inverter is for water supply and dry-running protectionProtection rating IP 68 The inverter installed on the pipe regulates constantly the pump activity; this unit utilizes only the necessary power supply in order to satisfy the required performancesThe electronic start doesn't cause water-hammer both switching on and stopping the pumpEasy regulationAlarm signal display with problem descriptionControl and safety system against over-currentProtection rating IP 68 Motor choice flexibility
Code
P2Nom.
Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 50 70 90 100 125 145A B H DNM DNAkW Hp Total Hm in CA
X1MOI100B 0,75 1 4 42 35 28 18 10 - - - 1.396,00 477 200 550 1"¼ 1" 18
X1MOI120B 0,90 1,2 5 52 43 40 35 30 25 20 11 1.422,00 477 200 550 1"¼ 1" 19
X1MOI1204BHF 0,90 1,2 4 43 38 34 30 27 24 16 6 1.447,00 560 200 550 1"¼ 1"¼ 20
X1MOI1505BHF 1,10 1,5 5 51 46 43 38 35 30 21 9 1.509,00 715 200 550 1"¼ 1"¼ 22
X1MOI2006HF 1,50 2,0 6 62 55 51 45 39 34 24 10 1.693,00 715 200 550 1"¼ 1"¼ 26HIG
H F
LOW
H
A
B
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure: to be regulated
Materials• Pump body, impellers and motor body: Stainless steel AISI 304 (standard versions)• Technopolymer impeller: High flow pumps• Technopolymer / Brass (2 HP model) flanges • Shaft: Stainless steel AISI 420• No return valve: brass• Mechanical seal: Graphite ceramics• Oil chamber on the mechanical seal• A2 Stainless steel bolts• NBR70 O-ring• H07RN-F Electric cable 5m length with Schuko plug• Class F insulated motors
105
Technopolymer motor support (up to 1,5 HP pumps)
Technolymer impeller
Apartments
Code n° Max flow l/min
X1MOI100B 2 ÷ 3 80
X1MOI120B 2 ÷ 4 80
X1MOI1204BHF 3 ÷ 4 130
X1MOI1505BHF 3÷ 4 130
X1MOI2006HF 3 ÷ 5 130
2006HF 1505HF
1204HF
120100
Curves and performance η = 2900 1/min
X1MOI B
Impeller Stainless steel AISI 304
Brass motor support (2HP pump)
1 - Multifunctional LCD screen. It shows the pressure in working mode.2 - MANUAL START-STOP pushbutton3 - Pushbutton for ENTER or EXIT menu. 4 - With these pushbuttons we can change programming values showed in the LCD screen (1)5 - ENTER for saving programmed values. Every pulsation is succeeded by a new field of the CONFIGURATION MENU. Whenever we want to quit the configuration sequence press MENU (3)6 - LED lights index: • LINE green: Electric supply. ON when it is connected • FAILURE red: Bright or intermittent depending on type of failure. • PUMP yellow: When it is bright means pump working. It is lit with the pump stopped or when the device is not connected. • AUTOMATIC green: It is bright in AUTOMATIC mode. When it is intermittent in MASTER&SLAVE mode it means that this device will be auxiliary in the following cycle.7 - ON/OFF: It allows to change from AUTOMATIC to MANUAL mode or viceversa.
X2MOI BElectronic booster set with inverter
106
Code
P2Nom.
3 ~ 50HzAmp.
1 ~ 50HzAmp.
Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 60 80 100 120 140 160 180A B C H DNM DNAkW Hp 230 V 400 V 230 V Total Hm in CA
X2MOI100B 0,75+0,75 1+1 3+3 6,0+6,0 6+6 4 42 35 30 28 24 18 15 10 3.511,00 800 200 620 800 2" 2" 35
X2MOI120B 0,90+0,90 1,2+1,2 3,3+3,3 2,5+2,5 7,2+7,2 5 52 43 40 35 30 25 20 11 3.671,00 800 200 620 800 2" 2" 37
DescriptionThe automatic system with inverter is for water supply and dry-running protectionProtection rating IP 68 The inverter installed on the pipe regulates constantly the pump activity; this unit utilizes only the necessary power supply in order to satisfy the required performancesThe electronic start doesn't cause water-hammer both switching on and stopping the pumpEasy regulationAlarm signal display with problem descriptionControl and safety system against over-current
Materials• Pump body, impellers and motor body: Stainless steel AISI 304 • Technopolymer flanges • Shaft: Stainless steel AISI 420• H07RN8-F Electric cable 10m length with Schuko plug• Inlet and outlet manifold: Stainless steel AISI 304• Class F insulated motors
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure rate switch 1,5 bar
H
CA
B
107
Technopolymer motor support (up to 1,5 HP pumps)
l/min
m³/h
500
400
300
200
100
40 0
10
20
30
40
50
60
0
0
40
2,4
80
4,8
120
7,2
160
9,6
200
12
260
15,6
120
100
DescriptionThe automatic system with inverter is for water supply and dry-running protectionProtection rating IP 68 The inverter installed on the pipe regulates constantly the pump activity; this unit utilizes only the necessary power supply in order to satisfy the required performancesThe electronic start doesn't cause water-hammer both switching on and stopping the pumpEasy regulationAlarm signal display with problem descriptionControl and safety system against over-current
Apartments
Code n° Max flow l/min
X2MOI100B 2 ÷ 3 180
X2MOI120B 2 ÷ 4 200
Curves and performance η = 2900 1/min
X2MOI B
Impeller Stainless steel AISI 304
Body pump: Stainless steel AISI 304
1 - Multifunctional LCD screen. It shows the pressure in working mode.2 - MANUAL START-STOP pushbutton3 - Pushbutton for ENTER or EXIT menu. 4 - With these pushbuttons we can change programming values showed in the LCD screen (1)5 - ENTER for saving programmed values. Every pulsation is succeeded by a new field of the CONFIGURATION MENU. Whenever we want to quit the configuration sequence press MENU (3)6 - LED lights index: • LINE green: Electric supply. ON when it is connected • FAILURE red: Bright or intermittent depending on type of failure. • PUMP yellow: When it is bright means pump working. It is lit with the pump stopped or when the device is not connected. • AUTOMATIC green: It is bright in AUTOMATIC mode. When it is intermittent in MASTER&SLAVE mode it means that this device will be auxiliary in the following cycle.7 - ON/OFF: It allows to change from AUTOMATIC to MANUAL mode or viceversa.
X2MVI HFElectronic booster set with inverter
108
Code
P2Nom.
Stag
es
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 60 100 140 200 240 290A B C H DNM DNAkW Hp Total Hm in CA
X2MVI1204BHF 0,90+0,90 1,2+1,2 4 43 38 34 30 24 16 6 3.699,00 560 150 620 1030 2" 2" 68
X2MVI1505BHF 1,10+1,10 1,5+1,5 5 51 46 43 38 30 21 9 3.831,00 560 150 620 1030 2" 2" 69
X2MVI2006HF 1,50+1,50 2,0+2,0 6 62 55 51 45 34 24 10 4.163,00 560 150 620 1030 2" 2" 72
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure: to be regulated
Materials• Pump body and motor body: Stainless steel AISI 304 • Technopolymer impeller• Technopolymer / Brass (2 HP model) flanges • Shaft: Stainless steel AISI 420• No return valve: brass• Pressure control manometer• Inlet and outlet manifold: Stainless steel AISI 304• Support base: Stainless steel AISI 304• Class F insulated motors
DescriptionUp/Down technology for submersed, surface or underground installation.For submerged and underground installation, the inverter control must be disconnected to place it in a protected area from moisture.The automatic system with inverter is for water supply and dry-running protectionProtection rating IP 68 The inverter installed on the pipe regulates constantly the pump activity; this unit utilizes only the necessary power supply in order to satisfy the required performancesThe electronic start doesn't cause water-hammer both switching on and stopping the pumpEasy regulationAlarm signal display with problem descriptionControl and safety system against over-currentProtection rating IP 68 Motor choice flexibility
HIG
H F
LOW
H
A C
B
109
Apartments
Code n° Max flow l/min
X2MVI1204BHF 4 ÷ 6 290
X2MVI1505BHF 6 ÷ 8 300
X2MVI2006HF 8 ÷ 10 300
Applications• Domestic boosting• Industrial installation boosting• Fountains and water playsPumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°CCalibrating pressure: to be regulated
0
0
040
200
100
300
400
500
600
10
20
30
40
50
60
70
2,4
40
4,8
80
7,2
120
9,6
160
12
200
14,4
240
16,8
280
19,2
320
2006
1505
1204
Curves and performance η = 2900 1/min
X2MVI HF
Technopolymer motor support (up to 1,5 HP pumps)
Technopolymer impeller
Brass motor support (only 2 HP version)
1 - Multifunctional LCD screen. It shows the pressure in working mode.2 - MANUAL START-STOP pushbutton3 - Pushbutton for ENTER or EXIT menu. 4 - With these pushbuttons we can change programming values showed in the LCD screen (1)5 - ENTER for saving programmed values. Every pulsation is succeeded by a new field of the CONFIGURATION MENU. Whenever we want to quit the configuration sequence press MENU (3)6 - LED lights index: • LINE green: Electric supply. ON when it is connected • FAILURE red: Bright or intermittent depending on type of failure. • PUMP yellow: When it is bright means pump working. It is lit with the pump stopped or when the device is not connected. • AUTOMATIC green: It is bright in AUTOMATIC mode. When it is intermittent in MASTER&SLAVE mode it means that this device will be auxiliary in the following cycle.7 - ON/OFF: It allows to change from AUTOMATIC to MANUAL mode or viceversa.
IRRIBOX JE/MOAll-In-One underground irrigation system IP68
110
Code
P2Nom.
1 ~ 50HzAmp. Zone
N°Garden
hose
Q (lt/m) FlowPrice
e
Dimensions mmWgt.
kg0 30 40 50 60 70 80 90 100A B H H1kW Hp 230 V Total Hm in CA
IRRIBOX JE2 0,90 1,2 6,3 2 OK 49 32 30 24 8 - - - - 1.759,00 820 570 400 300 37
IRRIBOX JE3 0,90 1,2 6,3 3 OK 49 32 30 24 8 - - - - 1.838,00 820 570 400 300 37
IRRIBOX JE4 0,90 1,2 6,3 4 OK 49 32 30 24 8 - - - - 1.917,00 820 570 400 300 37
IRRIBOX MO2 0,90 1,2 7,2 2 OK 52 43 40 35 30 25 20 15 8 1.874,00 820 570 400 300 37
IRRIBOX MO3 0,90 1,2 7,2 3 OK 52 43 40 35 30 25 20 15 8 1.954,00 820 570 400 300 37
IRRIBOX MO4 0,90 1,2 7,2 4 OK 52 43 40 35 30 25 20 15 8 2.033,00 820 570 400 300 37
Materials• Piping: PVC-U, Gaskets: EPDM• Underground well: reinforced polypropylene
Application• Domestic self-contained irrigation system.Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°C
DescriptionAll-In-One underground irrigation system with self-priming Jet pump JE or multistage pump MO• IP68 standard configuration• Electronic control system IP68• Solenoid valves IP68• Internal piping system PN16• Outlet water connection Zone 1”• Inlet water connections 1”• Rainwater sensor connections• Electrical cable H07RN8-F 20 m• Outlet connection garden hose• Internal washing connection• Lifting ropes • Max working pressure 16 bar
Water supply from well or tank
111
Outlet zone
Electronic control system IP68
Materials• Piping: PVC-U, Gaskets: EPDM• Underground well: reinforced polypropylene
Water connection for free use
H tkPa m 0 IMP. gal/min
0 US. gal/min
5 10 15 20
5 10 15 20 25 30
0 0
30
60
90
120
150
180
Htft
10 20 30 40 50 60 70 80 90 100 1100l/min
0m³/h 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5 5,5 6 6,5
10
20
30
40
50500
400
300
200
100
40
60
MO
JE
Application• Domestic self-contained irrigation system.Pumped liquid: Clean water with no abrasive or suspended solidsLiquid temperature +2°C ÷ +40°CAir temperature max +45°C
DescriptionAll-In-One underground irrigation system with self-priming Jet pump JE or multistage pump MO• IP68 standard configuration• Electronic control system IP68• Solenoid valves IP68• Internal piping system PN16• Outlet water connection Zone 1”• Inlet water connections 1”• Rainwater sensor connections• Electrical cable H07RN8-F 20 m• Outlet connection garden hose• Internal washing connection• Lifting ropes • Max working pressure 16 bar
Curves and performance η = 2900 1/min
IRRIBOX JE/MO
180° R = 4,5 m
180° 180° R = 5,5 m
R =7,5 m
R = 3,0 m
Code Zone N° Flowl/1' ÷ 3 bar
Spray heads for zone
ugello 10
Spray heads for zone
ugello 15
Spray heads for zone
ugello 17
Dinamic spray heads for zone
ugello ½ "
IRRIBOX JE2 2 40 12 / 13 4 3 4
IRRIBOX JE3 3 40 12 / 13 4 3 4
IRRIBOX JE4 4 40 12 / 13 4 3 4
IRRIBOX MO2 2 60 20 6 4 6
IRRIBOX MO3 3 60 20 6 4 6
IRRIBOX MO4 4 60 20 6 4 6
Single sprinkler flow 3 l/1' 10 l/1' 15 l/1' 12 l/1'
When a rain water storage tank is installed, it is wise to have a submersible pump installed to pressurize reclaimed water, and feed all home appliances... (toilets, washing machine, water taps outside the home, domestic garden irrigation ...)If there is prolonged absence of rain, reclaimed water will run out so it is necessary to install a rain water harvesting system directly from the aqueduct to feed the domestic appliances. (Fig. A)In accordance to the European law it is prohibited to allow reclaimed rainwater to come into contact with the mains water system in order to exclude any possibility of contamination or infection to the public network.It is therefore necessary to install a special kit to avoid any contamination and it must be clearly visible for any examination by authorities. (Fig. C) This special system, called ‘refeeding Kit’, does not allow in any circumstances the possibility of contact between mains pipes and reclaimed rainwater.This kit there includes an electric valve to control the water flow coming from the mains. This controlled flow avoids turbulences from the water within the ‘refeeding kit’ preventing harmful leakages of water as these leakages may cause damages to the surrounding structures in the long run. In addition, this regular flow control helps prevent harmful “hammerings” to the mains system avoid noise and damages to the water system, specifically to the household appliances. The presence of a
probe system ensures a fine and continuous check of the minimum rainwater level to prevent the pump going into alarm function due to lack of water. In the case of lack of water, a signal will be given to the control panel to open the electric valve of the ‘refeeding kit’.This type of probe system is integrated to the pump by a stainless steel support (Fig. B), granting always a minimum water level into the tank (4 / 6 cm).The pump turns on automatically in the case of water demand. It includes an anti-blocking system which checks the pump status every 72 hours and turns the pump on for 1 sec. in order to keep the rotor from the diffuser unlocked and to lubricate the two seals protecting the oil chamber.The technical condition of system can be seen by the customer on the control panel (Fig. C), where there pumps activity is shown. The customer will never have problems due to lack of rainwater when using this high-technical solution.Having the pump is installed inside the tank avoids any annoying noises, obstructions due to other smaller tanks, ugly rubbish bins to be installed close to the drip tray .... etc.
KR - RAINWATER HARVESTING SYSTEM
Rainharvesting system, boosting, water lifting, distribution of rainwater to the users
112
Washing machine
Rain water
Flow rupture kit
Mains supply
230 V~
Garden
Pump with floater
Control panel
Toilet
Tank
113
Code Description P2 Nominal power (HP) H max (m) Q max (lt/m) Price
e
KRJV80P KR with self-priming vertical pump 0,8 40 50 1.200,00
KRJV100P KR with self-priming vertical pump 1,0 47 60 1.211,00
KRJV120P KR with self-priming vertical pump 1,2 49 60 1.228,00
KRJE80B KR with self-priming horizontal pump 0,8 40 50 1.163,00
KRJE100B KR with self-priming horizontal pump 1,0 47 60 1.171,00
KRJE120B KKR with self-priming horizontal pump 1,2 49 60 1.182,00
KRMO100B KR with self-priming horizontal pump 1,0 42 90 1.263,00
KRMO120B KR with multistage horizontal pump 1,2 52 90 1.296,00
KRMO1505BHF KR with multistage horizontal pump HF 1,5 51 145 1.369,00
KRMO2006HF KR with multistage horizontal pump HF 2,0 62 145 1.566,00
KRMOV100B KR with multistage vertical pump 1,0 42 90 1.383,00
KRMOV120B KR with multistage vertical pump 1,2 52 90 1.414,00
KRMV1505BHF KR with multistage vertical pump HF 1,5 51 145 1.432,00
KRMV2006HF KR with multistage vertical pump HF 2,0 62 145 1.633,00
Electric valveWater inlet
Control panel
Refeeding kit
Fastening panel
Support delivery pipe
Electrical power 230 V ~ 50 Hz
Technopolymer check valveincluded
Probes
fig. B fig.C
Toilet
Mains supply
Washing machine
Tank
Probes system Garden
Rain water
When a rain water storage tank is installed, it is wise to have a submersible pump installed to pressurize reclaimed water, and feed all home appliances... (toilets, washing machine, water taps outside the home, domestic garden irrigation ...).If there is prolonged absence of rain, reclaimed water will run out so it is necessary to install a rain water harvesting system directly from the aqueduct to feed the domestic appliances.The KRS system is the best solution to have a storage promptly available and without waiting to reefed the tank.The user will have a quick application continuity,In accordance to the European law it is prohibited to allow reclaimed rainwater to come into contact with the mains water system in order to exclude any possibility of contamination or infection to the public network.It is therefore necessary to install a special kit to avoid any contamination and it must be clearly visible for any examination by authorities. (Fig. C)This special system, called ‘refeeding Kit’, does not allow in any circumstances the possibility of contact between mains pipes and reclaimed rainwater.In addition to the tank valve that is checked by the floater, there is another electric valve that prevents contacts between main pipes and rainwater. The floater has a spring-lock. This allows to go through a full flow to a stop flow, avoiding middle passages that could damage the system.This system separates the water flow of the mains from the domestic installations and helps prevent harmful“hammerings” to the mains system avoid damages to the water system, specifically to the household appliances.The presence of a probe system ensures a fine and continuous check of the minimum rainwater level to
prevent the pump going into dry-run alarm function due to lack of water. In the case of lack of water a signal will be given to the control panel to open the electric valve of the ‘refeeding kit’.This type of probe system is installed on a calibrated pipe with a foot valve, granting always a minimum water level into the tank. It is only necessary to fix the probe system in vertical position on the ground of tank without calibrating or setting or work testing.The pump turns on automatically in the case of water demand. It includes an anti-blocking system which checks the pump status every 72 hours and turns the pump on for 1 sec. in order to keep the rotor from the diffuser unlocked and to lubricate the two seals.At the first start the pump is primed easily through the priming valve control 1 and 2 (fig. C) (open the valves, when water goes out from the pipe the pump is primed).The technical condition of system can be seen by the customer on the control panel (Fig. B), where the pump activity is shown.The customer will never have problems due to lack of rainwater when using this high-technical solution.Having the pump is installed inside the box avoids any annoying noises, obstructions due to other smaller tanks, ugly rubbish bins to be installed close to the drip tray ... etc.
KRS - RAINWATER HARVESTING SYSTEM SUPERIOR
Rainharvesting system, boosting, water lifting, distribution of rainwater to the users
114
KRS - RAINWATER HARVESTING SYSTEM SUPERIOR
115
Code Description P2 Nominal (HP)/ H max (m) Q max (lt/m) Price e
KRSJE120P KR with automatic self-priming pump 1,2 60 60 2.328,00
fig. B
The suction kit 01IXV820P includes 20m electrical cable of probes with rapid connection to be connected directly to the control board. Moreover, the kit has a stainless steel filter and check valve with an already calibrated spring to make easy the pump suction. The hydraulic connection with the suction pipe (to be provided by customer) is with a 1” F connection. This product grants easy installation and moreover avoids the operation to regulate the water level feeding.
Cable 20m with probes connection
Level Probes
Check valve Filter
Ove flow
Refeeding kit with floater
Auxiliary tank
Suction from auxiliary tank
Main water system supply
Suction from rainwater tank
Electric valve
Valve 1 Priming
Sound proof wall
Valve 2 Priming
fig. C
KRQERain-water level control system
116
DescriptionThe rain-water level control system is necessary whenever the user utilizes an automatic rain-harvesting system. In the case that, in absence of rainfall, the recovery tank is empty, it is necessary to recover the water in order to use all home appliances getting from this rain-harvesting system. The KRQE unit automates this operation simply connecting the solenoid valve to the external water supply and installing the 4 probes group inside the recovery tank. The system automatically informs about the tank level by means of a signal led. This gives information whether the level is sufficient or if it is almost necessary to recover, or if the solenoid valve controls the filling.In case of absence of power supply the solenoid valve Normally Closed prevents that the external water supply is wasted for the refeeding.
Toilet
Mains supply
Tank
230 V~
ElectrovalveKRQE
Garden
Rain water
Washing machine
FEEDING WATERELECTROVALVE
RAIN WATER
WATER RESERVOIR
KRQE
117
Code Absorbed power Power supply Probes Dimensions mm Price e
KRQE00401 13 W 230 V ~ 50 Hz 4 154 x 200 x 79 H 605,00
Features• Automatic recovery in case of absence of rain-water• Signalling of attention water• Signalling of rain-water level • Signalling of recovery in operation • Control panel protection IP 54 • Signalling of feeding system
Components• Solenoid Valve Normally Closed• Solenoid valve ½” F-F• Solenoid valve body in brass• Level probes in stainless steel• Power cable 2mt with Schuko plug• Solenoid valve cable 2mt• Probes unit cable 20mt
XV4-10
118
Submersible pumps 4”
0
0
0
50
100
150
200
0,6
10
1,2
20
1,8
30
2,4
40
3
50
3,6
60
Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
60
50
10 20 30 40 50 600
28
20141007
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 180 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 410• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Noryl
DescriptionSubmersible pumps 4” with motor – Ø 1” ¼ outlet connectors
XV4-10
119
Curves and performance η = 2900 1/min
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 15 25 35 45 50
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV41007 0,37 0,5 3,1 - 46 43 39 33 26 22 505,00 644 -
1"¼
98 10,5 -
XV41010 0,55 0,75 5,0 - 69 65 60 50 37 29 539,00 717 - 98 11,9 -
XV41014 0,55 0,75 6,2 - 92 86 79 67 52 42 555,00 817 - 98 13,8 -
XV41020 1,1 1,5 8,5 - 139 131 120 101 75 60 682,00 952 - 98 16,2 -
XV41028 1,5 2 10,8 - 189 178 164 140 108 90 761,00 1173 - 98 20 -
3-PH
XV41007T 0,37 0,5 - 1,2 46 43 39 33 26 22 499,00 - 644
1"¼
98 - 10
XV41010T 0,55 0,75 - 1,6 69 65 60 50 37 29 525,00 - 697 98 - 11,1
XV41014T 0,55 0,75 - 2,2 92 86 79 67 52 42 542,00 - 787 98 - 12,7
XV41020T 1,1 1,5 - 3,0 139 131 120 101 75 60 638,00 - 922 98 - 15
XV41028T 1,5 2 - 4,2 189 178 164 140 108 90 723,00 - 1133 98 - 18,3
XV4 - 10
1-PH
Components Materials
1 Difussers Noryl GFN3V
2 Impellers Noryl GFN3V
4 Motor shaft Stainless steel AISI 304
5 Shaft sleeve Stainless steel AISI 410
6 Coupling Stainless steel AISI 410
7 Motor fitting CF8
8 Suction body CF8
9 Bearings NBR
10 Filter Stainless steel AISI 304
11 Upper support Noryl GFN3V
12 NRV base ABS
13 "O" Ring NBR
C
B
A
XV4-18
120
0
0
0
50
100
150
200
250
1,2
20
2,4
40
3,6
60
4,8
80
6
100
7,2
120
Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
50
60
70
20 40 60 80 100 1200
35
27
18
14
09
0507
XV4-18
Submersible pumps 4”
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 180 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 410• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Noryl
DescriptionSubmersible pumps 4” with motor – Ø 1” ¼ outlet connectors
121
Curves and performance η = 2900 1/min
3-PH
XV41805T 0,37 0,5 - 1,2 33 29 26 21 13 3 452,00 - 630
1"¼
98 - 9,9
XV41807T 0,55 0,75 - 1,6 46 43 40 33 21 7 468,00 - 674 98 - 10,8
XV41809T 0,75 1,0 - 2,2 59 55 51 43 28 10 492,00 - 737 98 - 12,1
XV41814T 1,1 1,5 - 3,0 93 87 81 68 43 20 546,00 - 874 98 - 14,2
XV41818T 1,5 2,0 - 4,2 120 113 105 88 60 25 603,00 - 991 98 - 16,1
XV41827T 2,2 3,0 - 6,2 175 164 152 127 87 35 872,00 - 1260 98 - 19,4
XV41835T 2,2 3,0 - 6,2 231 217 202 170 120 50 1.201,00 - 1447 98 - 21,9
XV4 - 18
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 25 40 60 80 100
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV41805 0,37 0,5 3,1 - 33 29 26 21 13 3 452,00 630 -
1"¼
98 10,4 -
XV41807 0,55 0,75 5,0 - 46 43 40 33 21 7 474,00 694 - 98 11,6 -
XV41809 0,75 1,0 6,2 - 59 55 51 43 28 10 501,00 767 - 98 13,2 -
XV41814 1,1 1,5 8,5 - 93 87 81 68 43 20 560,00 904 - 98 15,4 -
XV41818 1,5 2,0 10,8 - 120 113 105 88 60 25 636,00 1031 - 98 17,8 -
XV41827 2,2 3,0 15,5 - 175 164 152 127 87 35 798,00 1310 - 98 21,6 -
XV41835 2,2 3,0 15,5 - 231 217 202 170 120 50 832,00 - - 98 - -
1-PH
C
B
A
Components Materials
1 Difussers Noryl GFN3V
2 Impellers Noryl GFN3V
4 Motor shaft Stainless steel AISI 304
5 Shaft sleeve Stainless steel AISI 410
6 Coupling Stainless steel AISI 410
7 Motor fitting CF8
8 Suction body CF8
9 Bearings NBR
10 Filter Stainless steel AISI 304
11 Upper support Noryl GFN3V
12 NRV base ABS
13 "O" Ring NBR
XV4-35
122
30
2014
10
07
0
0
0
50
100
150
200
250
1,2
20
2,4
40
3,6
60
4,8
80
6 8,47,2
100 140120
9,6
160
Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
50
60
70
20 40 60 80 100 120 140 1600
XV4-35
Submersible pumps 4”
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 180 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 410• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Noryl
DescriptionSubmersible pumps 4” with motor – Ø 2” outlet connectors
123
Curves and performance η = 2900 1/min
3-PH
XV43507T 0,75 1,0 - 2,0 42 36 32 28 19 11 486,00 - 783
2"
98 - 12,5
XV43510T 1,1 1,5 - 3,0 62 53 48 41 29 18 537,00 - 906 98 - 14,7
XV43514T 1,5 2,0 - 4,2 90 77 71 63 46 28 595,00 - 1060 98 - 17,1
XV43520T 2,2 3,0 - 6,2 125 107 97 86 62 40 710,00 - 1324 98 - 20,7
XV43534T 4,0 5,5 - 9,4 208 178 162 143 103 66 1.129,00 - 1861 98 - 28,5
XV4 - 35
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 50 70 90 120 140
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV43507 0,75 1,0 16,0 - 42 36 32 28 19 11 495,00 813 -
2"
98 13,6 -
XV43510 1,1 1,5 8,0 - 62 53 48 41 29 18 549,00 936 - 98 15,9 -
XV43514 1,5 2,0 10,8 - 90 77 71 63 46 28 626,00 1100 - 98 18,8 -
XV43520 2,2 3,0 15,5 - 125 107 97 86 62 40 771,00 1374 - 98 22,9 -
1-PH
C
B
A
Components Materials
1 Difussers Noryl GFN3V
2 Impellers Noryl GFN3V
4 Motor shaft Stainless steel AISI 304
5 Shaft sleeve Stainless steel AISI 410
6 Coupling Stainless steel AISI 410
7 Motor fitting CF8
8 Suction body CF8
9 Bearings NBR
10 Filter Stainless steel AISI 304
11 Upper support Noryl GFN3V
12 NRV base ABS
13 "O" Ring NBR
XV4-40
124
32
232117
13
08
0
0
0
50
100
150
200
250
3 6
50 100
9 12
150 200
15
250
Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
50
60
70
50 100 150 200 2500
XV4-40
Submersible pumps 4”
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 180 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 410• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Noryl
DescriptionSubmersible pumps 4” with motor – Ø 2” outlet connectors
125
Curves and performance η = 2900 1/min
3-PH
XV44008T 1,5 2,0 - 4,2 52 48 46 39 29 24 581,00 - 871
2"
98 - 15,4
XV44013T 2,2 3,0 - 6,2 82 75 71 59 40 30 685,00 - 1066 98 - 18,7
XV44017T 3,0 4,0 - 7,1 108 98 94 79 58 46 888,00 - 12010 98 - 20,6
XV44021T 4,0 5,5 - 9,4 132 117 111 93 68 52 1.144,00 - 1402 98 - 24,1
XV44023T 4,0 5,5 - 9,4 148 134 127 108 79 60 1.163,00 - 1646 98 - 24,7
XV44032T 5,5 7,5 - 13,3 202 182 172 143 105 80 1.541,00 - 1861 98 - 30,6
XV4 - 40
1-PH
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 80 100 140 180 200
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV44008 1,5 2,0 10,8 - 52 48 46 39 29 24 614,00 911 -2"
98 17,1 -
XV44013 2,2 3,0 15,5 - 82 75 71 59 40 30 747,00 1116 - 98 20,9 -
C
B
A
Components Materials
1 Difussers Noryl GFN3V
2 Impellers Noryl GFN3V
4 Motor shaft Stainless steel AISI 304
5 Shaft sleeve Stainless steel AISI 410
6 Coupling Stainless steel AISI 410
7 Motor fitting CF8
8 Suction body CF8
9 Bearings NBR
10 Filter Stainless steel AISI 304
11 Upper support Noryl GFN3V
12 NRV base ABS
13 "O" Ring NBR
XV4-10X
126
33X28X
23X
18X
13X
09X
0
0
0
50
100
150
200
250
03 1,20,6 0,9 1,8 2,4
5 2010 15 30 40
1,5 2,1
25 35
2,7
45
Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
50
60
5 10 15 20 25 30 35 40 450
XV4-10X
Submersible pumps 4”
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 50 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 316• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Stainless steel AISI 304
DescriptionSubmersible pumps 4” with motor – Ø 1” ¼ outlet connectors
C
B
A
127
Curves and performance η = 2900 1/min
3-PH
XV41009XT 0,37 0,5 - 1,2 53 50 42 38 33 26 519,00 - 729
1"¼
98 - 10,2
XV41013XT 0,55 0,75 - 1,6 77 71 61 56 48 38 563,00 - 813 98 - 11,6
XV41018XT 0,75 1,0 - 2,2 106 98 84 77 66 51 628,00 - 838 98 - 13,5
XV41023XT 1,1 1,5 - 3 136 124 108 98 84 67 713,00 - 1073 98 - 15,8
XV41028XT 1,5 2,0 - 4,2 166 155 134 120 103 82 803,00 - 1208 98 - 18
XV41033XT 1,5 2,0 - 4,2 195 181 157 141 120 97 878,00 - 1336 98 - 21,1
XV4 - 10X
1-PH
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 15 25 30 35 40
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV41009X 0,37 0,5 3,1 - 53 50 42 38 33 26 524,00 729 -
1"¼
98 10,7 -
XV41013X 0,55 0,75 5 - 77 71 61 56 48 38 570,00 833 - 98 12,4 -
XV41018X 0,75 1,0 6,2 - 106 98 84 77 66 51 639,00 868 - 98 14,6 -
XV41023X 1,1 1,5 8,5 - 136 124 108 98 84 67 727,00 1103 - 98 17 -
XV41028X 1,5 2,0 10,8 - 166 155 134 120 103 82 835,00 1248 - 98 19,7 -
XV41033X 1,5 2,0 10,8 - 195 181 157 141 120 97 909,00 1376 - 98 22,8 -
Components Materials
1 Difussers Stainless steel AISI 304
2 Impellers Stainless steel AISI 304
3 Neck ring NBR
4 Motor shaft Stainless steel AISI 316
5 Coupling Stainless steel AISI 316
6 Motor fitting Stainless steel AISI 304
7 Suction body Stainless steel AISI 304
8 Bearings Stainless steel AISI 304
9 Filter Stainless steel AISI 304
XV4-18X
128
0
0
0
50
75
25
100
125
150
175
200
0,6 1,2 1,8 2,4
10 20 30 40
3
50
3,6 4,2
60 70
4,8
80
Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
60
50
10 20 30 40 50 60 70 800
29X25X
22X18X
15X
12X
09X
06X
XV4-18X
Submersible pumps 4”
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 50 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 316• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Stainless steel AISI 304
DescriptionSubmersible pumps 4” with motor – Ø 1” ¼ outlet connectors
129
Curves and performance η = 2900 1/min
3-PH
XV41806XT 0,37 0,5 - 1,2 38 34 31 29 22 17 478,00 - 666
1"¼
98 - 9,6
XV41809XT 0,55 0,75 - 1,6 58 54 49 47 36 25 518,00 - 729 98 - 10,08
XV41812XT 0,75 1 - 2,2 78 67 62 56 42 28 564,00 - 812 98 - 12,4
XV41815XT 1,1 1,5 - 3 97 84 78 71 52 38 624,00 - 905 98 - 14,3
XV41818XT 1,1 1,5 - 3 117 101 93 83 64 42 660,00 - 968 98 - 14,8
XV41822XT 1,5 2 - 4,2 143 123 115 103 77 52 732,00 - 1082 98 - 16,9
XV41825XT 1,5 2 - 4,2 162 140 128 113 86 58 762,00 - 1145 98 - 17,5
XV41829XT 2,2 3 - 6,2 188 162 149 133 98 67 873,00 - 1269 98 - 20
XV4 - 18X
1-PH
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 25 35 45 60 70
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV41806X 0,37 0,5 3,1 - 38 34 31 29 22 17 486,00 666 -
1"¼
98 10,1 -
XV41809X 0,55 0,75 5 - 58 54 49 47 36 25 523,00 749 - 98 11,6 -
XV41812X 0,75 1 6,2 - 78 67 62 56 42 28 574,00 842 - 98 13,5 -
XV41815X 1,1 1,5 8,5 - 97 84 78 71 52 38 639,00 935 - 98 15,5 -
XV41818X 1,1 1,5 8,5 - 117 101 93 83 64 42 672,00 998 - 98 16 -
XV41822X 1,5 2 10,8 - 143 123 115 103 77 52 763,00 1122 - 98 18,6 -
XV41825X 1,5 2 10,8 - 162 140 128 113 86 58 795,00 1185 - 98 19,2 -
XV41829X 2,2 3 15,5 - 188 162 149 133 98 67 932,00 1319 - 98 22,2 -
C
B
A
Components Materials
1 Difussers Stainless steel AISI 304
2 Impellers Stainless steel AISI 304
3 Neck ring NBR
4 Motor shaft Stainless steel AISI 316
5 Coupling Stainless steel AISI 316
6 Motor fitting Stainless steel AISI 304
7 Suction body Stainless steel AISI 304
8 Bearings Stainless steel AISI 304
9 Filter Stainless steel AISI 304
XV4-25X
130
0
0
0
50
100
150
200
250
1,2
20
2,4
40
3,6
60
4,8
80
6
100
7,2
120
Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
50
60
70
20 40 60 80 100 1200
33X
25X21X17X12X
08X06X
04X
XV4-25X
Submersible pumps 4”
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 50 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 316• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Stainless steel AISI 304
DescriptionSubmersible pumps 4” with motor – Ø 1” ¼ outlet connectors
131
Curves and performance η = 2900 1/min
3-PH
XV42504XT 0,37 0,5 - 2,1 25 22 20 19 17 12 453,00 - 624
1"¼
98 - 9,2
XV42506XT 0,55 0,75 - 1,6 38 34 32 30 26 17 489,00 - 666 98 - 10,2
XV42508XT 0,75 1,0 - 2,2 57 44 42 40 35 22 520,00 - 728 98 - 11,6
XV42512XT 1,1 1,5 - 3 75 68 65 63 53 36 596,00 - 842 98 - 13,7
XV42517XT 1,5 2,0 - 4,2 106 95 90 85 73 50 680,00 - 977 98 - 15,9
XV42521XT 2,2 3,0 - 6,2 131 117 110 103 90 62 790,00 - 1101 98 - 18,5
XV42525XT 2,2 3,0 - 6,2 156 140 131 127 110 74 834,00 - 1185 98 - 19,2
XV42533XT 3,0 4,0 - 7,1 209 182 173 165 142 98 1.070,00 - 1381 98 - 23,6
XV4 - 25X
1-PH
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 30 40 50 70 100
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV42504X 0,37 0,5 3,1 - 25 22 20 19 17 12 461,00 624 -
1"¼
98 9,7 -
XV42506X 0,55 0,75 5 - 38 34 32 30 26 17 494,00 686 - 98 11 -
XV42508X 0,75 1,0 6,2 - 57 44 42 40 35 22 530,00 758 - 98 12,7 -
XV42512X 1,1 1,5 8,5 - 75 68 65 63 53 36 608,00 872 - 98 14,9 -
XV42517X 1,5 2,0 10,8 - 106 95 90 85 73 50 711,00 1017 - 98 17,6 -
XV42521X 2,2 3,0 15,5 - 131 117 110 103 90 62 850,00 1151 - 98 20,7 -
XV42525X 2,2 3,0 15,5 - 156 140 131 127 110 74 893,00 1235 - 98 21,4 -
C
B
A
Components Materials
1 Difussers Stainless steel AISI 304
2 Impellers Stainless steel AISI 304
3 Neck ring NBR
4 Motor shaft Stainless steel AISI 316
5 Coupling Stainless steel AISI 316
6 Motor fitting Stainless steel AISI 304
7 Suction body Stainless steel AISI 304
8 Bearings Stainless steel AISI 304
9 Filter Stainless steel AISI 304
XV4-40X
132
30X
21X
18X
0 1,2 2,4 3,6 4,8 6 7,2 8,4 9,6 10,8 12
0 20 40 60 80 100 120 140 160 180 200
0
50
100
150
200Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
50
60
70
20 40 60 80 100 120 140 160 180 2000
12X10X
07X05X
15X
XV4-40X
Submersible pumps 4”
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 50 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 316• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Stainless steel AISI 304
DescriptionSubmersible pumps 4” with motor – Ø 2” outlet connectors
133
Curves and performance η = 2900 1/min
3-PH
XV44005XT 0,75 1,0 - 2,2 30 26 24 23 19 10 583,00 - 805
2"
98 - 13,1
XV44007XT 1,1 1,5 - 3,0 41 36 33 32 25 15 668,00 - 919 98 - 15,4
XV44010XT 1,5 2,0 - 4,2 58 52 50 49 40 27 781,00 - 1075 98 - 18,2
XV44012XT 2,2 3,0 - 6,2 69 63 60 58 49 32 907,00 - 1199 98 - 21
XV44015XT 2,5 3,0 - 6,2 86 79 75 72 60 40 986,00 - 1325 98 - 22,5
XV44018XT 3,0 4,0 - 7,1 103 91 87 83 70 48 1.199,00 - 1471 98 - 24,8
XV44021XT 4,0 5,5 - 9,4 121 111 104 100 82 54 1.497,00 - 1627 98 - 28,6
XV44030XT 5,5 7,5 - 13,3 173 155 147 139 114 74 1.845,00 - 2085 98 - 36,4
XV4 - 40X
1-PH
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 40 70 90 140 180
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV44005X 0,75 1,0 6,21 - 30 26 24 23 19 10 594,00 835 -
2"
98 14,2 -
XV44007X 1,1 1,5 8,5 - 41 36 33 32 25 15 680,00 949 - 98 16,6 -
XV44010X 1,5 2,0 10,8 - 58 52 50 49 40 27 813,00 1115 - 98 19,9 -
XV44012X 2,2 3,0 15,5 - 69 63 60 58 49 32 967,00 1249 - 98 23,2 -
XV44015X 2,2 3,0 15,5 - 86 79 75 72 60 40 1.045,00 1375 - 98 24,7 -
C
B
A
Components Materials
1 Difussers Stainless steel AISI 304
2 Impellers Stainless steel AISI 304
3 Neck ring NBR
4 Motor shaft Stainless steel AISI 316
5 Coupling Stainless steel AISI 316
6 Motor fitting Stainless steel AISI 304
7 Suction body Stainless steel AISI 304
8 Bearings Stainless steel AISI 304
9 Filter Stainless steel AISI 304
XV4-70X
134
25X
13X
10X
07X05X
18X
0 3 6 9 12 15 18 21
0 50 100 150 200 250 300 350
0
20
40
60
80
100
120
140
160
180Ht (m)
η %
Efficiency
l/min
0
10
20
30
40
50
60
70
50 100 150 200 250 300 3500
XV4-70X
Submersible pumps 4”
Applications• Suitable for clean water• For agricultural installation • Irrigation• Industrial and domestic pressurizing systems• Sand content: Max 50 g/m³
Materials• Pump body, upper and lower closure: Stainless steel AISI 304• Motor body, lower closure: Stainless steel AISI 304• Upper motor body closure: Stainless steel AISI 304• Motor shaft: Stainless steel AISI 316• Mechanical seal: Graphite ceramics• Diffusers and Impellers: Stainless steel AISI 304
DescriptionSubmersible pumps 4” with motor – Ø 2” outlet connectors
135
Curves and performance η = 2900 1/min
3-PH
XV47005XT 1,5 2 - 4,02 32 29 27 26 23 13 703,00 - 958
2"
98 - 16,4
XV47007XT 2,2 3 - 6,02 45 40 37 36 32 18 847,00 - 1128 98 - 19,5
XV47010XT 3 4 - 7,01 65 58 54 52 46 26 1.097,00 - 1343 98 - 22,2
XV47013XT 4 5,5 - 9,04 85 75 70 67 60 34 1.431,00 - 1568 98 - 26,5
XV47018XT 5,5 7,5 - 13,03 117 104 97 93 83 46 1.730,00 - 1973 98 - 33
XV47025XT 7,5 10 - 18 163 145 135 130 115 65 2.194,00 - 2658 98 - 46,3
XV4 - 70X
1-PH
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm Weight kgA
B C0 100 140 160 200 300
1-PH 3-PHkW Hp 230 V 380 V 1-PH 3-PHTotal Hm in CA
XV47005X 1,5 2 10,08 - 32 29 27 26 23 13 734,00 998 -
2"
98 11,4 -
XV47007X 2,2 3 15,05 - 45 40 37 36 32 18 907,00 1178 - 98 13,2 -
C
B
A
Components Materials
1 Difussers Stainless steel AISI 304
2 Impellers Stainless steel AISI 304
3 Neck ring NBR
4 Motor shaft Stainless steel AISI 316
5 Coupling Stainless steel AISI 316
6 Motor fitting Stainless steel AISI 304
7 Suction body Stainless steel AISI 304
8 Bearings Stainless steel AISI 304
9 Filter Stainless steel AISI 304
ACCESSORIES FOR SUBMERSIBLE PUMPS
136
Box with capacitorControl panel with protected light switch with capacitor for submersible pump.Single-phase motor without capacitor on board.
• Single-phase electric supply 230V ± 10% 50 Hz• Ambient temperature -2°C + 40°C• Protection rating IP55• Seal cable glands • Internal block terminal
Code Descriptiuon Dimensions mm Pricee
KITCE6000416 Box with capacitor 0,5HP 16 μF 0,37 Kw 114 x 75 x 200 H 44,00
KITCE6000420 Box with capacitor 0,75HP 20 μF 0,55 Kw 114 x 75 x 200 H 45,00
KITCE6000430 Box with capacitor 1HP 30 μF 0,75 Kw 114 x 75 x 200 H 46,00
KITCE6000440 Box with capacitor 1,5HP 40 μF 1,1 Kw 114 x 75 x 200 H 49,00
KITCE6000450 Box with capacitor 2HP 50 μF 1,5 Kw 114 x 75 x 200 H 51,00
KITCE6000470 Box with capacitor 3HP 70 μF 2,2 Kw 114 x 75 x 200 H 55,00
BLAK
GREY
BROWN
CAPACITOR
POWER LINE
YELLOW / GREEN
Connection diagram for single-phase motor
ACCESSORIES FOR SUBMERSIBLE PUMPS
137
Box with capacitor
Part of flat cable with plug for submersible motors 4 "
Code Section Length m PPrice e
01CEP100C 4 x 1,5 mm2 10 79,00
01CEP200C 4 x 1,5 mm2 20 150,00
01CEP300C 4 x 1,5 mm2 30 210,00
01CEP500C 4 x 1,5 mm2 50 331,00
01CEP200C2 4 x 2 mm2 20 190,00
01CEP300C2 4 x 2 mm2 30 268,00
01CEP500C2 * 4 x 2 mm2 50 422,00
Electric cable for potable waterFor higher cable length, it is possible to add an electric connection.
Electrical cables with a circular section dimensioning table
Power230 V single-phase 50 Hz DIRECT STARTING Cables section 4 x … mm²
1,5 2,5 4 6 10 16 25 35 50
Cv / Hp kW Cable max length (mm)
0,5 0,37 91 151 241 362 - - - - -
0,75 0,55 72 121 193 290 483 - - - -
1 0,75 52 86 138 207 345 - - - -
1,5 1,1 36 60 97 145 241 340 - - -
2 1,5 30 50 80 121 201 298 - - -
3 2,2 - 37 60 90 151 230 398 - -
230 V Three-phase 50 Hz DIRECT OR STATOR STARTING No. 1 Cable – Section 4 x … mm²
0,5 0,37 181 302 - - - - - - -
0,75 0,55 155 258 412 - - - - - -
1 0,75 126 211 337 506 - - - - -
1,5 1,1 85 42 227 341 568 - - - -
2 1,5 68 114 182 274 456 - - - -
3 2,2 46 76 122 183 306 489 - - -
4 3 34 56 90 135 224 359 561 - -
5,5 4 - 43 70 104 174 278 435 - -
7,5 5,5 - 32 52 78 129 207 324 453 -
10 7,5 - - 38 57 94 151 236 330 472
400 V Three-phase 50 Hz DIRECT OR STATOR STARTING No. 1 Cable – Section 4 x … mm²
0,5 0,37 454 - - - - - - - -
0,75 0,55 346 576 - - - - - - -
1 0,75 302 504 806 - - - - - -
1,5 1,1 227 378 605 - - - - - -
2 1,5 165 242 388 581 - - - - -
3 2,2 123 205 328 492 - - - - -
4 3 89 148 236 354 590 - - - -
5,5 4 76 127 204 306 509 - - - -
7,5 5,5 58 97 155 232 387 619 - - -
10 7,5 - 71 114 171 285 455 - - -Cable lengths refer to 30°C ambient temperature; in air installation, cos Φ = 0,8 and admitted tension fall = 3%
* Not for 3HP pumps
I-DRENO
138
Submersible drainage pumps
DescriptionSingle-phase pump, submersible for drainage.Protection rating IP68.Free passage solid bodies: - 50 Ø 8 mm- 100 Ø 10 mm- 200 Ø 11 mm- 300 Ø 11 mmClass F insulated motors
Applications• Slushy water, waste water without solids• Drainage application, flood control• Dewatering of ponds and basements
Materials• Volute, impeller, upper cover and body pump in grey iron.• Motor body in Stainless Steel AISI 304• Motor shaft in Stainless Steel AISI 410• Double mechanical seal: Carbon/Ceramic-SIC/SIC• Class F insulated motors
1-PH
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm
DNM Wgt.kg100 150 200 300 400 500 600
L HkW Hp 230 V 230 V 400 V Total Hm in CA
I-DRENO50 0,37 0,50 3,5 - - 8,3 5,5 2,2 - - - - 272,00 230 355 50 15
I-DRENO100 0,75 1 6 - - 12,5 11 9,4 5,5 - - - 354,00 277 440 50 19
I-DRENO200 1,5 2 10 - - 19,9 18 17 14,8 12,2 9,2 6 874,00 412 569 80 44
I-DRENO300 2,2 3 15 - - 27 26 24,5 21,2 16,6 10,5 - 912,00 412 572 80 46
AU
TO 1
-PH
3-PH
I-DRENO50AUT 0,37 0,50 3,5 - - 8,3 5,5 2,2 - - - - 293,00 230 355 50 15
I-DRENO100AUT 0,75 1 6 - - 12,5 11 9,4 5,5 - - - 378,00 277 440 50 19
I-DRENO200AUT 1,5 2 10 - - 19,9 18 17 14,8 12,2 9,2 6 910,00 412 569 80 44
I-DRENO300AUT 2,2 3 15 - - 27 26 24,5 21,2 16,6 10,5 - 960,00 412 572 80 46
I-DRENO50T 0,37 0,50 - 1,8 1,2 8,3 5,5 2,2 - - - - 308,00 230 355 50 15
I-DRENO100T 0,75 1 - 3,0 2,2 12,5 11 9,4 5,5 - - - 435,00 277 440 50 19
I-DRENO200T 1,5 2 - 4,8 4,2 19,9 18 17 14,8 12,2 9,2 6 838,00 412 470 80 44
I-DRENO300T 2,2 3 - 7,0 6,2 27 26 24,5 21,2 16,6 10,5 - 872,00 412 493 80 46
Automatic single-phase version with float switch
139
Curves and performance η = 2900 1/min
Applications• Slushy water, waste water without solids• Drainage application, flood control• Dewatering of ponds and basements
0
0
0
3
6
9
12
15
18
21
24
27
30
100
6
200
12
300
18
500
30
400
24
600
36
700
42
I-DRENO
300
200100
50
Float switch
Thermal protection
Impeller
Handle
Cable
Cable base
Lower bearing
Lower bearing housing
Stator body
Lubrificant
Oil seal
Impeller
Strainer
Mechanical shaft seal
Mecahnical seal cover
Upper cover
Upper bearing
Shaft
Stator
Rotor
Outlet pipe
Flange
Volute
Automatic reset motor protector
I-VOR
140
Submersible pumps VORTEX
DescriziptionSingle-phase pump, submersible for drainage with impeller VORTEX.Protection rating IP68.
Applications• Civil and industrial sewage with suspended solids• Drainage waste or sump drainage water with or without solids (max 400 mm)
Materials• Volute, impeller and upper cover in Stainless steel AISI 304• Motor body and pump body in Stainless Steel AISI 304• Outlet in Stainless Steel AISI 304• Motor shaft in Stainless steel AISI 410• Mechanical seal: SIC/SIC• Class F insulated motors
Code
P2Nom.
1 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mmDNM Wgt.
kg50 100 150 200 250 300A B C D E F GkW Hp 230 V Total Hm in CA
I-VOR50AUT 0,37 0,50 3,5 6,4 5,4 4,3 3,1 1,7 - 288,00 430 123 235 241 55 550 290 50 9,5
I-VOR100AUT 0,75 1 6 7,6 6,5 5,3 3,9 2,5 1 308,00 430 123 235 241 55 550 290 50 9,5
141
Curves and performance η = 2900 1/min
Applications• Civil and industrial sewage with suspended solids• Drainage waste or sump drainage water with or without solids (max 400 mm)
Float switch
Suction
Vortex Impeller
Cable base
Handle
Upper cover
Body cover
Upper bearing housing
Float switch
Shaft
Rotor
Impeller
V-ring sand guard
Voluta
Lower bearing
Upper bearing
Lower bearing housing
Mechanical shaft seal
Outlet
Volute base cover
Stator
0
0
0
1
2
3
4
5
6
7
8
9
10
50
3
100
6
150
9
250
15
200
12
300
18
250
21
I-VOR
10050
1-PH
Code
P2Nom.
1 ~ 50HzAmp.
3 ~ 50HzAmp.
Q (lt/m) FlowPrice
e
Dimensions mm
Exha
ust
Inle
t
DNM Wgt.
kg100 150 200 300 400 500 600A B CkW Hp 230 V 230 V 400 V Total Hm in CA
DRENOBOX50 0,37 0,50 3,5 - - 8,3 5,5 2,2 - - - - 1.152,00 550 800 940 100 2" 28
DRENOBOX100 0,75 1 6 - - 12,5 11 9,4 5,5 - - - 1.244,00 550 800 940 100 2" 33
DRENOBOX200 1,5 2 10 - - 19,9 18 17 14,8 12,2 9,2 6 1.823,00 550 800 940 100 2" 57
DRENOBOX
142
Automatic pumping station with I-DRENO pumps
DescriptionDrainlift for fully assembled dirty water. Suitable for pumping untreated sewage that cannot be conveyed to the sewer system by gravity flow.Surface and underground installation. The system includes the I-DRENO pump with float switch and check valve on delivery.Rapid connection to the pump through the pipe. Polyethylene tank 170 lPower supply 220 V – 50 Hz
ApplicationsDrains coming from:• Showers, toilets, saunas• Toilets in basements• Drainage of cellars, buildings, etc.
Pump characteristic• Volute, impeller, upper cover and body pump in grey iron.• Motor body in Stainless steel AISI 304• Motor shaft in Stainless steel AISI 410• Double mechanical seal: Carbon/Ceramic-SIC/SIC• Class F insulated motors Free passage solid bodies: - 50 Ø 8 mm- 100 Ø 10 mm- 200 Ø 11 mm- 300 Ø 11 mm
143
Curves and performance η = 2900 1/min
ApplicationsDrains coming from:• Showers, toilets, saunas• Toilets in basements• Drainage of cellars, buildings, etc.
0
0
0
3
6
9
12
15
18
21
24
27
30
100
6
200
12
300
18
500
30
400
24
600
36
700
42
I-DRENO
300
200100
50
1 10 100
100
10
1
1000
Qr
(m3 /
h)
Persons (N°)
Max flow of drained domestic water during peak time
Residential Hospitals Industries Offices Flowat switch
I-DRENO pump into the station
Hg
Hm
t
ΔPc
Hmt - Max hydraulic headHg - Hydraulic head utilized from the pumpΔPc -Work pressure
ACCESSORIES
146
Code Description Pricee
01CEP005C Electric connections IP68 23,00
Code Description Pricee
01IXP372C Inox suction filter 1” 8,00
Code Description Pricee
N150 Suction kit with floating ball 55,00
Code Description Pricee
C150 Suction kit with floating ball and check valve 71,00
Code Description Pricee
01PCP045C Technopolymer check-valve 1” 21,00
01PCP107C Technopolymer check-valve 1” ¼ 43,00
147
Code Description Pricee
01VEP125C Stainless steel AISI 304 2 l ¾” 90,00
Code Description Pricee
02PLP584G Technopolymer transportation handle 15,00
Code Description Pricee
01VEP001C Stainless steel 24 l tank 416,00
Code Description Pricee
01PCP010C Pressure switch Square D ¼” M 9,00
Code Description Pricee
01PCP110C Inverter M/T 10AMP 485,00
01PCP121C Inverter M/M 12AMP 486,00
Code Description Pricee
01GEA992C Float switch with electric cable 2 m 22,00
01GEA993C Float switch with electric cable 3 m 23,00
01GEA995C Float switch with electric cable 5 m 28,00
01GEA910C Float switch with electric cable 10 m 38,00
01GEA915C Float switch with electric cable 15 m 54,00
01GEA920C Float switch with electric cable 20 m 66,00
148
Code Description Pricee
X-FC5 Filter 5” – Cartridge box 28,00
X-FC7 Filter 7” – Cartridge box 29,00
X-FC10 Filter 10” – Cartridge box 30,00
Code Description Pricee
X-IX5 Stainless Steel filtering cartridges INOX 5” 90,00
X-IX7 Stainless Steel filtering cartridges INOX 7” 96,00
X-IX10 Stainless Steel filtering cartridges INOX 10” 106,00
X-NY5 Nylon filtering cartridges 5” 20,00
X-NY7 Nylon filtering cartridges 7” 22,00
X-NY10 Nylon filtering cartridges 10” 23,00
X-FIL5 Wound wire filtering cartridges 5” 10,00
X-FIL7 Wound wire filtering cartridges 7” 11,00
X-FIL10 Wound wire filtering cartridges 10” 12,00
X-CA5 Active carbon filtering cartridges 5” 31,00
X-CA7 Active carbon filtering cartridges 7” 32,00
X-CA10 Active carbon filtering cartridges 10” 35,00
X-PL5 Polyphosphate filtering cartridges 5” 32,00
X-PL7 Polyphosphate filtering cartridges 7” 35,00
X-PL10 Polyphosphate filtering cartridges 10” 36,00
ACCESSORIES
PAYMENTS:Our invoices are payable in accordance with the methods established and accepted when ordering. Any delay or irregularity in payments as well as any irregularity in performing the contract on the part of the buyer constitute non-fulfilment with resultant default action. Any expenses are at buyer charge in case of non-payment.
SUPPLIES:Agreements or promises that are different from the standard supply conditions are not recognized unless approved in the order confirmation.
RETURNS:Goods returns are not accepted for any reason unless otherwise authorized by Steelpumps Srl through the original RMA module.
SHIPMENT:The goods are carried at the risk of the buyer even when sent carriage free. In the case of dispute, the buyer must immediately inform the carrier of the event by registered mail with a copy to us. However, once eight days have lapsed from receipt of the goods, claims are no longer permitted.
DELIVERY:Delays due to force majeure, or any other reason, do not justify the cancellation of the order, nor may any compensation requested. Partial deliveries, i.e. performed at different successive stages, are also authorized. The delivery date of the supply is never to be considered final or essential.
GUARANTEE:The general guarantee is valid for two years, starting from the date of dispatch of the material. Of course, the guarantee covers any manufacturing defect of the material that we ourselves produce. Our guarantee is limited to the replacement or repair, in our workshop and by us, of the pump or part that is identified as being faulty. In no case, however the guarantee involves the possibility of requesting compensation. Breakdowns caused by errors in electrical connection, by a lack of adequate protection, by defective assembly, by incorrect action or by a lack of care during the installation are excluded from the guarantee:The warranty is not recognized when the buyer is not up-to-date with payments.In particular, our guarantee is void in absence of documentation proving the date of shipment and overall without the test certification given together with the pump. Finally, material removed, repaired or tampered with by any person not expressly authorized by Steelpumps, it is excluded from our guarantee. The faulty material must be returned to our workshops carriage free and, once it is recognized that the fault comes under our responsibility, it will in turn be returned carriage free.
DISPUTES:There may be no exception to the conditions stated above unless expressed and accepted in writing. The resolution of any dispute falls within the jurisdiction of the Court of Pisa, even if the payment is agreed by means of a draft.
STEELPUMPS srl
GENERAL SALES CONDITIONS
150
To obtain this innovative, completely automatic
and self-contained electropump, Steelpumps
has adopted the clients’ point of view. The
achieved result is a range of pumps, capable
of satisfying different needs.
It is reliable, easy to install and use.
“The different pump”
www.steelpumps.it
GRAFICAFranco Ferrucci
STAMPATipografia Monteserra
COPYRIGHTSteelpumps srl
Printed in Italy
Steelpumps Srl reserves the right to make changes to its products without prior notice
STEELPUMPS srl - Via Sicilia - Z. I. Perignano56035 Lari (PI) ITALY
+39 0587 466722 / +39 0587 466188+39 0587 466775 / +39 0587 466747
FAX +39 0587 365138
e-mail: info@steelpumps.it
venditeitalia@steelpumps.ittecnico@steelpumps.it
assistenza@steelpumps.it
www.steelpumps.it
Company headquarter Project Production Quality control
CG
LP02
- 02
018
- ED
GB
2018GENERAL CATALOGUE
P R I C E L I S T
ITALIAN PRODUCT
50Hz
GEN
ERA
L C
ATA
LOG
UE
2018
5
0H
z
Recommended