View
1
Download
0
Category
Preview:
Citation preview
49.2cc 2-cycle2.0HP 10 Inch TinesCULTIVATOR
MODEL NO.536.292510536.292520
Caution:Read and follow all SafetyRules and Operatingnstructions before first use_f this product.
SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A.
712452 12/09198
Table of Contents 2Warranty 2Safety Rules 2-4Contents of Shipping Carton 4Assembly 4Operation 5-8Maintenance 9-10
Service and Adjustments 11-12Storage 12-13Troubleshooting 13Cultivator Repair Parts 14-16Engine Repair Parts 17-20Spanish (Espa5ol) 21-34Parts Ordering/Service Back Cover
LIMITED ONE-YEAR WARRANTY ON CRAFTSMAN CULTIVATOR
For one year from the date of purchase, when this Craftsman cultivator is maintained,lubricated, and tuned up according to the operating and maintenance instructions inthe owner's manual, Craftsman will repair, free of charge, any defect in material orworkmanship.
This warranty excludes tine(s), spark plug, and air cleaner which are expendable partsand become worn during normal use.
If this Craftsman cultivator is used for commercial or rental purposes, this warranty ap-plies for only 30 days from the date of purchase. This warranty applies only while thisproduct is in use in the United States. WARRANTY SERVICE IS AVAILABLE BY RE-TURNING THE CULTIVATOR TO THE NEAREST CRAFTSMAN SERVICE CENTERIN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights whichvary from state to state.
SEARS, ROEBUCK AND CO., D817WA, Hoffman Estates, IL 60179
,_ Look for this symbol to point out important safety precautions. It means --ATFENTIONI!! Become alertlll Your safety is involved,
Z_ CAUTION: Always disconnect sparkplug wire and place wire where it cannotcontact spark plug to prevent accidentalstarting when setting-up, transporting,adjusting or making repairs.
IMPORTANT: Safety standards requireoperator presence controls to minimize therisk of injury. Your cultivator is equippedwith such controls. Do not attempt to defeatthe function of the operator presencecontrol under any circumstances.BEFORE USE
• Read the owner's manual carefully. Bethoroughly familiar with the controls andthe proper use of the cultivator. Know
how to stop the cultivator and disengagethe controls quickly.
• Do not operate the cultivator without
wearing adequate outer garments. Wearfootwear that will improve footing onslippery surfaces.
"o Keep the area of operation clear of all
persons, particularly small children andpets.
• Thoroughly inspect the area where thecultivator is to be used and remove all
foreign objects.
FUEL SAFETY .
• Handle fuel with care; it is highly flam-mable.
• Use an approved container.
• Check fuel supply before each use,allowing space for expansion as the heatof the engine and/or sun can cause fuel toexpand.
• Fill fuel tank outdoors with extreme care.
Never fill fuel tank indoors. Replace fueltank cap securely and wipe up spilledfuel.
• Never remove the fuel tank cap or addfuel to a running or hot engine.
• Never store fuel or cultivator with fuel inthe tank inside a building where fumesmay reach an open flame.
OPERATING SAFETY
• Never allow children or young teenagersto operate the cultivator. Keep themaway while it is operating. Never allowadults to operate the cultivator withoutproper instruction.
• Do not operate this machine if you aretaking drugs or other medication whichcan cause drowsiness or affect yourability to operate this machine.
,, Do not use this machine if you arementally or physically unable to operatethis machine safely.
• Always wear safety glasses or eyeshields during operation or while perform-ing an adjustment or repair to protectyour eyes from foreign objects that maybe thrown from the cultivator.
• Do not put hands or feet near or underrotating parts.
• Exercise extreme caution when operatingon or crossing gravel drives, walks, orroads. Stay alert for hidden hazards ortraffic.
• Exercise caution to avoid slipping orfalling.
• Never operate the cultivator withoutproper guards, plates, or other safetyprotective devices in place.
• Never operate the cultivator at hightransport speeds on slippery surfaces.Look behind and use care when backing.
• Never allow bystanders near the cultiva-tor.
• Keep children and pets away whileoperating.
• Never operate the cultivator without goodvisibility or light.
• Do not run the engine indoors. Theexhaust fumes are dangerous, containingCARBON MONOXIDE, an ODORLESSand DEADLY GAS.
• Take all possible precautions whenleaving the cultivator unattended. Stopthe engine.
• Do not overload the cultivator capacity byattempting to till too deep at too fast arate.
SAFE STORAGE
• Always refer to the owner's manualinstructions for important details if thecultivator is to be stored for an extended
period.• Never store the cultivator with fuel in the
fuel tank inside a building where ignitionsources are present such as water andspace heaters, clothes dryers, and thelike. Allow the engine to cool beforestoring in any enclosure.
• Keep the cultivator in safe workingcondition. Check all fasteners at frequentintervals for proper tightness.
REPAIPJADJUSTMENTS SAFETY
• After striking a foreign object, stop the
engine. Remove the wire from the sparkplug, and keep the wire away from theplug to prevent accidental starting.Thoroughly inspect the cultivator for anydamage, and repair the damage beforerestarting and operating it.
• If cultivator should start to vibrate
abnormally, stop engine and checkimmediately for the cause. Vibration isgenerally a warning of trouble.
• Stop the engine whenever you leave theoperating position. Also, disconnect thespark plug wire before unclogging thetines and when making any repairs,adjustments, or inspections.
• When cleaning, repairing, or inspecting,shut off the engine and make certain allmoving parts have stopped.
• Never attempt to make any adjustmentswhile the engine is running except whenspecifically recommended by the manu-facturer.
Z_ WARNING: The engine exhaustfrom this product contains chemicalsknown to the State of California to causecancer, birth defects or other reproductiveharm.
_ WARNING: This unit is equippedwith an internal combustion engine andshould not be used on or near any unim-proved forest-covered, brush-covered orgrass-covered land unless the engine's ex-haust system is equipped with a spark ar-rester meeting applicable local or state laws(if any). If a spark arrester is used, it shouldbe maintained in effective working order bythe operator.
In the state of California the spark arrester is on federal lands. A spark arrester/muffler isrequired by law (Section 4442 of the Califor- available through your nearest Craftsmannia Public Resources Code). Other states Authorized Service Center (See REPAIRmay have similar laws. Federal laws apply PARTS section in this manual).
Parts packed separately in carton (not shown full size)
1 - 5.3 Ounce 2-cycle Oil1 - Owner's Manual (not shown)
ACAUTION: Always wear safety
glasses or eye shields while assemblingthe Craftsman cultivator.
The figure to the right shows the cultivatorcompletely assembled.References to the right or left hand sideof the cultivator are from the viewpoint ofthe operator's position behind the unit.TO REMOVE CULTIVATOR FROMCARTON
• Remove packing insert from carton.• Lift the cultivator out of the carton and
place on a hard level surface.• Loosen tee knobs. Tilt the cultivator
forward and rotate upper handle to theupright position, making sure the throttleis not caught between the handles. Thentighten the tee knobs. See figure below.
• Tighten the handle hardware by holdingthe curved head carriage bolt against theoutside of the lower handle while
tightening the tee knobs securely.
ht LeftHandle
Control
DepthStake
Tine
,/ CHECKLIST
Before you operate and enjoy your newCRAFTSMAN CULTIVATOR, to ensurethat you receive the best performance andsatisfaction from this quality product, pleasereview the following checklist:
J All assembly instructions have beencompleted.
,I No loose parts in carton.
,/ All fasteners have been properlytightened.
While learning how to use your CRAFTS-MAN CULTIVATOR, pay extra attention tothe following important items:
,/,/ Fuel tank is filled with correct gasolineand oil mixture.
,/,/ Become familiar with the location and
function of all controls. Operatecontrols before starting engine.
KNOW YOUR CULTIVATORREAD THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOURCRAFTSMAN CULTIVATOR. Compare the illustrations with your cultivator to familiarizeyourself with the location of various controls and adjustments. Save this manual for futurereference.
Choke Off AHalf Choke
FoI, Choke I\1Right SideUpper Handle
Control
@Stop
Left SideUpper Handle
Left SideLower Handle
Choke
FuelTank
Right SideLower Handle
Depth Stake/Transport Wheels,Assembly
Depth Rc_/Transport
Assembly
Shield
Throttle Control - Controls the enginespeed and the tine rotation. This cultivator isequipped with a centrifugal clutch that en-gages the tine ddve system when the en-gine speed is increased.Choke Control Lever - Used to assist in
starting a cold engine.On-Off Switch - ON - Allows the unit to bestarted. OFF - Stops the engine and keepsthe unit from being started.
Recoil Starter Handle - The engine on thiscultivator is equil_ped with an easy pull re-coil starter.
Depth Stake or Depth Rod/TransportWheels Assembly - Used (with wheels up)when cultivating to adjust the depth of thecut. It also acts as a brake to help the op-erator control the direction and speed of theunit.
The depth stake or depth rod/transportwheel assembly (with wheels down) can beused for transporting the unit.
HOW TO USE YOUR CULTIVATOR
/_ WARNING: The operation of this cul-
tivator can result in foreign objects beingthrown into the eyes, which can cause se-vere eye damage. Always wear safetyglasses or eye shields while operating theunit.
We recommend standard safety glasses orWide Vision Safety Mask for over yourglasses.
TO STOP CULTIVATOR
• Release the throttle control to stop thetines.
• Move the on-off switch on the engine tothe OFF position.
OPERATE CULTIVATOR
Set the depth stake or depth rod/transportwheels assembly to the desired tillingposition as follows:
• Remove the hairpin from the clevis pinsecuring the depth stake or depth red.Remove the clevis pin and adjust the
depth stake or depth red upward to digshallower or downward to dig deeper.Reinstall the clevis pin and hairpin.
Depth Stake/TransportWheelsAssembly \
Wheel Support RodAssembly
throttle control all the way up against thehand grip. The engine is govemorcontrolled and should be run at full throttle.
• Grasp the handles firmly and slowly tilt theunit forward to begin the tilling action.
• As the tines begin to make contact with theground, hold back on the handles so thatthe tines will dig and not ride forward over
the ground. Hold back until the tines diginto the soil.
• If the tilled depth is too deep or tooshallow, turn off the engine and reset thedepth stake or depth rod.
• If depth stake or depth rod is not control-ling forward action, lower the depth stakeor depth red. If the unit is not goingforward, raise the depth stake or depthrod.
/K CAUTION: Keep away from the ro-
tating tines. Rotating tines can cause in-jury.BEFORE STARTING ENGINE
FILL GAS
The two cycle engine used on this cultivatorrequires a mixture of gasoline and oil for lu-brication of the bearings and other movingparts. The correct fuel mixture ratio is 24:1(see Fuel Mixture Chart). Gasoline and oilmust be premixed in a clean gasoline con-tainer. Always use fresh, clean unleaded
Clevis Pin.X_ gasoline.Dep_ Stake_ /_. CAUTION: Gasoline is flammableurac_t _ and caution must be used when handling
_ __ or storing it. Do not fill fuel tank while culti-__ vator is running hot or when it is in an en-
Hairptn._. _ L--_ closed area. Keep fuel away from open"_ '_ '_'_ flame and electrical spark. DO NOT
I_ SMOKE while mixing fuel or filling the fuel
_J tank. Never fill fuel tank completely, but fillit to within 1/4 - 1/2 inch from the top to
Dep_ Round
• Start the engine, tilt the unit back on thedepth stake or depth red until the tinesare off the ground and squeeze the
provide space for expansion of fuel. Al-ways fill fuel tank outdoors and use a fun-nel or spout to prevent spilling; Make sureto wipe up 0ny spilled fuel before startingthe engine.
Store gasoline in a clean, approved con-tainer, and keep the cap in place on thecontainer. Keep gasoline in a cool, well-ventilated place, never indoors. To assurevolatility, never buy more than a 30 daysupply of gasoline. Gasoline is intended tobe used as a fuel for internal combustionengines; therefore, do not use gasoline forany other purpose. Since many children
like the smell of gasoline, keep it out oftheir reach because the fumes are dan-gerous to inhale, as well as being explo-sive.
Z_ WARNING: Experience indicatesthat alcohol blended fuels (called gasohol orusing ethanol or methanol) can attract mois-ture which leads to separation and forma-tion of acids during storage. Acidic gas candamage the fuel system of an engine whilein storage. To avoid engine problems, thefuel system should be emptied before stor-age for 30 days or longer. Drain the gastank, start the engine and let it run until thefuel lines and carburetor are empty. Usefresh fuel next season. See Storage Instruc-tions for additional information. Never useengine or carburetor cleaner products in thefuel tank or permanent damage may occur.GASOLINE AND OIL MIXTURE
Mix gasoline and oil 24:1 as follows:
• Pour 1 U.S. quart of fresh, clean,unleaded automotive gasoline into agallon gasoline container.
• Add 5.3 oz.(found in carton) of clean,high quality SAE 30 or SAE 40 two-cycleoil into the gasoline container.IMPORTANT: DO NOT use OutboardMotor Oil or Multi-Viscosity Oils, suchas 10W-30 or 10W-40.
• Reinstall the cap on the gasoline con-tainer and shake container vigorously sothe oil mixes with the gasoline.
• Add an additional 3 U.S. quarts ofgasoline to the gallon container andshake the container again.
• This completes the special gasolinemixing procedure. It can now be pouredinto the cultivator fuel tank.
IMPORTANT: DO NOT fill fuel tank withgasoline that does not have oil mixed init. Do not use gasoline additives becausethe engine may be damaged. Shake thegasoline container before each filling ofthe fuel tank.
Add More Gas(3 U.S. Quarts)
or 5.3 oz.
1 U.S. '_.Gallon Shake CanContainer
FUEL MIXTURE CHART (Mixture 24:1)
u.S. S.I. (METRIC)
GAS OIL GAS OIL
1 Gal. 5.3 oz. 4 Liters .167 L
2 Gal. 11 oz. 8 Liters .333 L
5 Gal. 27 oz. 20 Liters .833 L
TO START THE ENGINE
Before starting the engine, be sure youhave read and understood all the instruc-
tions on the preceding pages.• Fill the fuel tank to 1/2 inch below the
bottom of the fill neck with fresh fuel mix
and reinstall the fuel tank cap securely.Never use fuel that may be stale fromlong periods of storage.
• Move the on-off switch to the ON
position.• Move the choke control (see figure, page
5) to the FULL CHOKE position (all theway down).
NOTE: A warm engine should not requirechoking.
• Tilt the cultivator back on the depth stakeor transport wheels to raise the tines offthe ground.
• Grasp the upper handle firmly to stabilizethe cultivator.
• Move shut-off toggle switch to ON.• Move choke lever to FULL CHOKE
position.• Grasp starter handle and pull slowly until
you feel drag.• Return starter handle slowly to original
position.• Pull handle with rapid, full arm strokes
until engine starts.• When engine starts, move choke lever to
HALF CHOKE position.• When engine runs smoothly, move choke
lever to NO CHOKE position.NOTE: If the tines do not stop when thethrottle control is released, adjust thecarburetor idle speed as instructed inCarburetor Adjustment paragraph in theService/Adjustments section on page 11.
• To stop the engine, release the throttlecontrol and move the on-off switch to the
OFF position.
• If the engine becomes flooded, see theSpark Plug Maintenance paragraph in theMaintenance section of this manual.
Then pull the starter rope with the chokelever in the NO CHOKE position.
Z_ CAUTION: The muffler and sur-rounding areas become hot after runningthe engine. Avoid these areas.
CULTIVATING HINTS
• Tilling is digging in, turning over andbreaking up packed soil before planting.Loose unpacked soil helps root growth.Best tilling depth is 4 to 6 inches. A tillerwill also clear the soil of unwanted
vegetation. The decomposition of thisvegetation matter enriches the soil.Depending on the climate (rainfall andwind), it may be advisable to till the soil atthe end of the growing season to furthercondition the soil.
• Avoid tilling soil that is too dry as it willpulverize and produce a dust that will nothold water. Also, tilling soil that is too wetwill be hard on the machine and produceunsatisfactory clods.
• Better growth will be obtained in tilledground if a relatively small area is tilledproperly and the tilled ground is usedsoon after tilling to preserve the moisturecontent.
• The depth stake (on the back of thecultivator) serves a dual purpose (seefigure, page 6). It helps regulate thedepth of the cut to a uniform level andalso acts as a brake to help the operatorcontrol the speed of the cultivator.
• Lowering the depth stake will slow thecultivator and make it till deeper. Raisingthe depth bar will allow it to move fasterand till more shallow.
• If the cultivator stops forward motion andtries to dig deeper than necessary, movethe handles from side to side to startforward motion.
• Cultivating is loosening or digging aroundgrowing plants which allows the plants tofloudsh.
• When using the cultivator to removeweeds, it is best to cultivate no deeperthan 1-1/2 inches. Cultivating deeper willonly pull to the surface ungerminatedweed seeds. You may want to raise thedepth bar to lessen the braking action.
• When cultivating around plants or closeareas, you may want to remove theoutside tines (see Tine Replacementparagraph in the Service/Adjustmentssection of this manual).
/_ CAUTION:• Read the Owner's manual.• Know location and functions of all
controls.
• Keep all safety devices and shields inplace.
• Never allow children or uninstructed
adults to operate cultivator.• Shut off engine before unclogging tines or
making repairs.• Keep bystanders away from machine.• Keep away from rotating parts and tines.
They can cause injury.
PRODUCT SPECIFICATIONS
MODEL NO. 536.292510
536.292520
DATE CODE:
DATE OFPURCHASE:
HORSE POWER: 2 HP
DISPLACEMENT: 3.0 cu. in.(49.2 cc)
GASOLINE CAPACITY: 20 oz.
FUEL/OIL MIX RATIO: 24:1 Gas To Oil
(Use Unleaded Regular) 5.3 Oz. Oil/1 Gal. Gas
SPARK PLUG : Champion
(Gap .035 in.)RCJ -8Y
IDLE RPM: 1700-3000
8
CUSTOMER RESPONSIBILITIES
SERVICERECORDS
Fill in dates asyou completeregular service
TightenAll Screws and Nuts
LubricateTine Shaft
LubricateTransmission
Check Spark Plug
Clean end Re-Oil Air Cleaner Filter
CylinderExhaustPo_ls
DrainFuel
SCHEDULE
Before After Every Every Before BeforeEach first 2 25 75 Storage EachUse , Hours Hours Hours Season
_," v"_," v*ii j
v_
SERVICEDATES
GENERAL RECOMMENDATIONS
The warranty on this cultivator does notcover items that have been subjected to op-erator abuse or negligence. To receive fullvalue from the warranty, the operator mustmaintain the cultivator as instructed in thismanual. The above chart is provided to as-sist the operator in properly maintaining thecultivator.
LUBRICATION
Every 25 hours and/or at the beginning ofeach season, the gear box should be filledwith lubricant. Tubes of gear lubricant areavailable from most automotive supplystores. Use portable tool grease such asLubriplate 630AA (Product No. 06787, 1-3/4oz. tube) or Lubriplate GR-132 (Product No.15892, 10 oz. tube). The tine shaft shouldhave oil applied to it before storage and af-ter it is cleaned by flushing it with water.The illustration to the right is provided to as-sist the operator in propedy maintaining thecultivator.
Z_ CAUTION: Allow the transmission to
cool before filling with grease.• Remove both left side tines. See Service
and Adjustments section in this manual.• Remove the air vent screw from the top
left side of the transmission.
• Using a grease gun, fill the transmissionthrough the grease fitting until the newgrease begins to come out of the air ventscrew hole.
• Reinstall the air vent screw.• Check the condition of the felt washer in
the side of the transmission at the tine
shaft. Replace the felt washer if it isdamaged (see Repair Parts section inthis manual).
• Clean tine shaft and spread a few dropsof oil on shaft in tine replacement areas.Reinstall the tines.
• Remove the right side tines. Check thefelt washer for damage, clean and oil thetine shaft. Reinstall the tines.
Transmission
Air Vent Screw Tine Shaft(Oil the tineshaft beforestorage andafter cleaning,if the cultivatoris flushedwithwater)
Felt-
Grease fitting(Lubricatethe gearbox withLubriplate630AA orLubriplate GR-132
View of Left Side With Tines Removed
ENGINE
SPARK PLUG M_NTENANCE
If the engine is flooded, clean the areaaround the spark plug base to prevent for-eign material from entering the cylinderswhen the plug is removed. Remove and drythe spark plug. Regap the electrodes to.035" if necessary. If a new spark plug isneeded, refer to the Product Specificationschart in this manual for the proper replace-ment. Tighten the spark plug firmly. If atorque wrench is available, torque the sparkplug to 15 foot- pounds.
AIR CLEANER MAINTENANCE
The air cleaner filter should be cleaned andre-oiled after every 25 hours of use. Cleanmore often under dusty conditions.
IMPORTANT: The engine can be worn outin a very short period of time if dirt or grit isallowed to enter the engine.
To clean the air filter, do the following:• Loosen screws on air cleaner cover and
remove the cover.• Remove foam element from air cleaner.
Foam Element
bg Cover
• Wipe inside of air cleaner housing clean.• Clean foam element by washing in strong
solution of water and household deter-
gent. Rinse thoroughly in clean water.• Wrap foam element in clean cloth and
squeeze out (do not twist) all the liquiduntil dry.
• Cover the ends and side of the foamelement with same oil used in fuelmixture. Knead the foam element
between fingers to distribute oil andremove excess oil.
• Reinstall foam element in air cleanerhousing.
• Service foam element carefully. Inspectfor deterioration or damage. A defective,improperly serviced, or mistakenlyassembled air filter will allow dirt particlesto enter the engine.
• Reassemble the filter. Place the cover onthe air cleaner housing and tighten screwsto secure cover to the housing.
Z_ CAUTION: Never run engine withoutair cleaner element installed. A defective aircleaner can result in loss of engine powerand cause excessive wear or damage to en-gine components if dirt or dust is permittedto enter the engine through the carburetor.An air cleaner that is clogged with dust ordirt should be cleaned and re-oiled.
CYLINDER EXHAUST PORTS
The cylinder exhaust ports should becleaned after each seventy-five (75) to onehundred (100) hours of operation. For thisprocedure we recommend that you takeyour unit to a Craftsman Service Center,
CLEANING
Always remove the dirt and debris from thecultivator after each use. Remove anystring, wire or vegetation that may becomelodged in the mechanism and stop the linerotation. Proceed as follows:
• Release the throttle control and move theon-off switch to the OFF position, thendisconnect the spark plug wire.
• Remove the hairpin and clevis pinsecuring the tine(s) assembly to the shaftand remove the tine(s).
• Remove the lodged material. Reassemblethe tine(s) on the shaft and secure with aclevis pin and hairpin.
• Reconnect the spark plug wire and restartthe engine.
Front View
Clevis Pins Lodged Item Clevis ;'ins
10
Tines Hairpinsission Side
pins Tines
TINE REPLACEMENT
The cultivator is left hand or right hand asviewed from the operator's position behindthe unit,
All four tines on this unit are different andcannot be interchanged. The tines must beproperly installed as shown in figures to theright or the cultivator will not function prop-erly.
For working close around plants or in smallareas, the outside tines may be removed toreduce the tilling width to about 7 inches, Toreinstall the outside tines see below.
Z_ CAUTION: The tines are self sharp-ening and will become quite sharp fromuse. Handle carefully.
The tines will all wear fairly evenly. If thetines are being replaced because of wear,we recommend that all four tines be re-placed at the same time. To replace thetines, do the following:• Place the on-off switch to the OFF
position and disconnect the spark plugwire.
• While wearing gloves, remove thehairpins and the clevis pins from the tineson one side of the unit and then remove
the tines. See figure, previous page.• Clean the tine shaft and oil it at the tine
locations.• Place the inside tine on the tine shaft and
reinstall the clevis pin and hairpin.• When the tines are properly installed, the
letter R will be visible on the outside of
the right-hand tine (the letter L on the left-hand fine). The letter should appearopposite the small hole in the side of thetine.
• Place the outside tine on the tine shaft
and reinstall the clevis pin and hairpin.• The outside tine cutting tips will all bend
in toward the inside tine. The letter R on
the right side or L on the left side shouldbe visible from the outside of the unit.
• Repeat the above steps on the oppositeside of the unit.
• Check to make sure the tines areinstalled on correct side of the unit.
Properly Installed Right Side Tines
Right Side indicator
CARBURETOR ADJUSTMENT
A dirty air cleaner will cause the engine torun improperly and/or smoke excessively.Be sure the air cleaner is clean before ad-justing the carburetor. Never make unnec-essary adjustments to the carburetor. Thecarburetor was set at the factory to operateefficiently under most applications. How-ever, if adjustments are required, we recom-mend you contact your nearest CraftsmanService Center. If you feel that you are com-petent to make carburetor adjustment pro-ceed as follows:
m_a CAUTION: Use extreme whencare
ing adjustments that require the engineto be running. Keep hands, feet, hair andloose clothing away from any moving part.
• Turn the mixture adjustment screwclockwise to close.
IMPORTANT: Tighten the adjustingscrew with your fingers to prevent dam-age to the carburetor or adjusting screw.Turn the mixture screw counterclockwise
open one (1) turn.Start the engine and let it warm upapproximately 3 to 5 minutes. Do notadjust the c_rburetor when the engine iscold.
If the engine falters or stops after thechoke lever is moved to the CHOKE OFF
position, open the mixture adjusting screwan additional 1/8 turn counterclockwise.
With the engine running, release thethrottle control (idle position) to make themixture adjustments. Then perform thefollowing:
1t
•Tum the mixture adjusting screw slowlyclockwise until the engine falters. Notethis location.
•Tum the mixture adjusting screw slowlycounterclockwise until the engine starts
to sputter. Note this location.• Turn the mixture adjusting screw
clockwise until it is halfway between the
first position where the engine falteredand the second position where the
engine started to sputter.
Idler SpeWedAdjustingScrew
AdjustingScrew
Engine Shown With Air Cleaner Removed
The idle speed may need to be adjustedafter making the mixture adjustment. If"the tines do not turn when the engine isrunning and the throttle control isreleased, the idle speed will not needadjusting. If the tines turn when thethrottle control is released, do thefollowing:• Have someone tilt the cultivator back
on its depth stake so that the tines areoff the ground.
• Start the engine.• With the throttle in the released (idle)
position, turn the idle speed adjustingscrew countemlockwise until the tines
stop rotating.
,_ CAUTION: Never tamper with the en-
gine governor which is factory set for properengine speed. Over-speeding the engineabove the factory set high speed can bedangerous. If you think the engine-governedhigh speed needs adjusting, contact yournearest Craftsman Service Center.
AZ..._CAUTION: Never store engine withfuel in tank indoors or in enclosed, poorlyventilated areas where fuel fumes manyreach an open flame, spark or pilot light ason a furnace, water heater, clothes dryer,etc.
NOTE: The cultivator should be immedi-ately prepared for storage at the end of theseason or if the unit will not be used for 30
days or more.
CULTIVATOR
• Thoroughly clean the cultivator. Removeall dirt and debris from the engine andunit.
• Remove the tines, oil the tine shaft andreinstall the tines (see Service andAdjustments section in this manual).
• Loosen the tee knobs that secure the
upper handle to the lower handle.• Carefully fold the upper handle down,
making sure the throttle is not kinked.Tighten the tee knobs.
The cross piece of the upper handle(between the lower handles) can now beused as a carry handle or can be hookedover a wall hook to store the cultivator upoff the floor and out of the way.If possible, store your cultivator indoorsand cover it to give protection from dustand dirt.Cover the cultivator with a suitable
protective cover that does not retainmoisture. Do not use plastic.
IMPORTANT: Never cover the cultivator
while th_ engine and exhaust areas arestill warm.
NOTE: A yearly checkup or tune-up by aCraftsman Service Center is a good wayto ensure that your cultivator willprovide maximum performance for thenext season.
ENGINE
IMPORTANT: It is important to preventgum deposits from forming in essential fuelsystem parts such as the carburetor, fuel fil-ter, fuel hose or tank during storage. Also,experience indicates that alcohol blendedfuels (called gasohol or using ethanol ormethanol) can attract moisture which leadsto separation and formation of acids duringstorage. Acidic gas can damage the fuelsystem of an engine while in storage.
• Drain the fuel from the fuel tank into an
approved container outdoors, away fromopen flame.
Start and run the engine until it stops dueto lack of fuel.
Pull the starter hand!e slowly until youfeel resistance due to compressionpressure, then stop.Release the starter tension slowly toprevent the engine from reversing due tocompression pressure. This position willclose both the intake and exhaust ports toprevent corrosion of the piston andcylinder bore.
TROUBLE CAUSE CORRECTION
Difficult starting Stale fuel mixture Drain fuel tank. Fill with freshmixture.
or Too much oil in mixture Check fuel mix chart and mixfresh fuel.
Engine runs errati Dirt in fuel tank or out of fuel Clean fuel tank. Fuel tankshould be half full when start-
cally ing engine.
or Carburetor out of adjustment See Carburetor Adjustmentsection.
Engine will not Fouled spark plug Clean and re-gap plug.run at full speed
Plugged air cleaner Clean and re-oil air cleaner.
Engine speed Debris interfering with throttle link- Blow dirt and debris off top ofdoes not increase age carburetor.
properly
Engine smokes Plugged air cleaner Clean and re-oil air cleaner.
excessively Too much oil in fuel mixture Check fuel mix chart and mix
fresh fuel.
Tines continue to Carburetor out of adjustment Adjust carburetor idle speed.rotate when See Carburetor Adjustment
throttle control is in Service and Adjustmentsreleased section of this manual.
Tines will not turn Foreign object lodged in tine Remove lodged item. SeeCleaning in the Maintenancesection of this manual.
Unit does not till Incorrect tine installation Check the tines for properproperly installation. See the Tine
Replacement in the Ser-vice and Adjustments sec-tion of this manual.
CRAFTSMAN10" -2 H.P. CULTIVATOR 536.292510/536.292520
ENGINE ASSEMBLY
REF.NO. PART NO.10 ENGINE
111 5669412 33535013 120380
14 18004217 319306
712452
PART NAME2 HP 143.982070(Bee Engine pages)Flatwasher, .378xl .25x.06 HtRotorWasher, Regsptlk.263x.49x.0_Screw, 1/4-20xl .75Cable, ThrottleOwner's Manual
Ali unnumbered items ereinterchangeable with oppositeslde
SHIELD
323392C
Note: Always use original equipmentparts. Use of service/replacementpartsother than original parts may voidyour warranty.
TRANSMISSION ASSEMBLY
310
--300
REF.
NO. PART NO. PART NAME
300 740061 Transmission Assy.310 340550 Bracket, Assy Depth Flat Bar310 340549 i Bracket, Assy Depth Round Bar311 180024 Screw, 1/4-20xl.25
312 782585 Nut, 1/4-20 Reghexctrlk
318848C
14
CRAFTSMAN 10" - 2 H.P. CULTIVATOR 536.2925101536.292520
TINE SHIELD ASSEMBLY
48O
492
J,95
REFNO. PART NO. PART NAME480 !309073-848 Tine Shield481 273869 Screw, 1/4-20x5.00482 120392 Flatwasher.281x.63x.065
483 46931 Nut, 1/4-20 Wdfl Lock490 56158 Felt Washer .68xl .46x.12491 56157-853 Tine, Assy InnerLH
REF.NO" PART NO.492 ;56155-853
493 156156-853494 156154-853
495 56123496 56180
PART NAMETine, Assy Outer LHTine, Assy Inner RHTine, Assy Outer RHClevis Pin .31xl .38Hair Pin .091Diax1.62Lg
318849D
FLAT BAR ASSEMBLY
650
f-. 662/.
662 .LDf:-! " DEPTHeAR
661 _ii!'ii
ROUND BAR ASSEMBLY
650
661
662\
DEPTH BARASSEMBLY660
REF.NO,
85O660861562563
PART N O.330799-8533336355618033927773664
PART NAME
Wheel Supt Assy Drag StakeClevis Pin .321x.75
Hair Pin .091 Diax1.62LgTire & Rim
Nut, Push On 3/8"318852F
REF.NO. PARTNO.
650 331282
660 333635661 56180662 339277663 73664
PART NAMEWheel Suppt Assy RodClevis Pin .321x.75Hair Pin .091Diax1.62LgTire & RimNut, PushOn 3/8"
323396B
CRAFTSMAN10" - 2 H.P. CULTIVATOR 536.292510/536.252520
DECALS
DETHATCHERDEBRIS SHIELD
(REF)._\\
\\
820\
PART NO.
320711712457305828
PART NAMEReference OnlyDecal, CautionDecal, Tine ShieldCraftsmanDecal, Caution (Starting Inst)
320229C
,821/
_ / CULTIVATOR_ ,/ DEBRIS SHIELD
_ " (REF.)
824
C.
HANDLE ASSEMBLY
REF, ITEM
THROTTLE CONT_
\,.,.- \
PART NO.56237-853339398-853339399-853561997830001203931352712037656778426635712267
PART NAME
Upper HandleLower Handle, LH
Lower Handle, RHCarr. Bolt, 5116-18xl .63Formed WasherFlatwasher .344x.69x.065
T Knob, 2/Blade w/516/18Nut, 5/16-18 Reghex
Hand GripScrew, 10-16xl .50 TapCable Tie
319375C
16
CRAFTSMAN 2-CYCLE ENGINE MODEL NUMBER: 143.982070Carburetor No. 640901
REF. PARTNO. NO.
640901
12
33A3B456717
202127
2830313445
2
632954632928
632926632950632949632939A
632929A632930632931632946640908640904
632916632915632918632920632917632919
PART NAMECarburetor(Incl. 184 of Engine Parts List)Throttle Shaft & Lever Ass'y.
Throttle Return SpringDust Seal RetainerDust Seal Retainer Screw
SpacerDust Seal Washer
Dust SealThrottle ShutterThrottle Shutter Screw
Idle Speed ScrewIdle Mixture Screw
Idle Tension Spring
Hinge Pin• Metering Lever* Inlet Needle
Metering Lever SpringMetering Lever Pin Screw
• Fuel Inlet Screen
REF.
NO.
4850
51
525360
6162
63
6465
686970
17
PARTNO.
,632902632904
632903
632905632906632933
640909632908
632907
632988632945
640906640907632934
PART NAME
* Welch Plug* Diaphragm
(Included in 60 & 70)* Cover Gasket
(Included in 60 & 70)CoverCover Screw
Repair Kit(Incl. items marked * in notes)Module Clamp Screw
* Pump Diaphragm
(Included in 60 & 70)• Pump Gasket
(Included in 60 & 70)Pump CoverPump Cover Screw
Adjustment Umiter ModuleAdjustment Limiter CapDiaghragm/Gasket Set(Incl. 50_ 51_ 62 & 63)
CRAFTSMAN 2-CYCLE ENGINE MODEL NUMBER: 143.982070
[_ J 26"L
370-0 _'-298'-- '_"297
277
16E16C-
18423O
18
CRAFTSMAN 2-CYCLE ENGINE MODEL NUMBER: 143.982070
REF.NO. PART NO.1 250303
13
13A
16B
16C
19
2030
39
42
44
69
7778
79
89
9091
91 A
91 B
92
93
100
101103
1110
119
135
177
178
184
187187 A
2O0
203
204209
210
211216
23O
243243 A
245
650888
270288A
270298490324650986
570716
510328
290664310285A
310275530163
510348
530110
510319
650844
611054611180
590691
590692
650985
650848650849
611056
610118651007
611135510349
611049
650858
650580
510327B
570648A570698A
570700
570701
651042651042
27793
651047570712
570649A
650955650964
450252
PART NAME
Cylinder(Incl. 119,184,187&187._Screw, Torx T-30,4-20 x 43/84"Crankcase Ass'y.(Incl. 20 & 44)Crankcase Cover Ass'y.Air VaneScrew, Torx T-8,3-48 x 7/32"Governor SpringOil SealCrankshaftPiston & Rod Ass'y.(Incl. 42)Ring SetCartridge Bearing"O" RingBall BearingOil SealScrew, 1/4-20 x 3/4"Flywheel KeyFlywheelPawl SpringStarter PawlScrew, 12-24 x 11/64"BellevUleWasherFlywheel NutSolid State Ignition(Incl. 101)Spark Plug CoverScrew, Torx T-15,10-24 x 15/16"Ground WireCylinder Head GasketResistor Spark Plug(RCJ8Y)Carburetor MountingStudLock Nut, 10-24Carburetor GasketSpacerAir Baffle
Speed Control BodyCompression SpringScrew, T-15, 8-32 x 1"Screw, T-15, 8-32 x 1"Conduit ClipScrew,T-15 10-24x21/32'R.P.M. Adjusting Lever"O" RingScrew, 10-32 x 29/32"Thread InsertAir Cleaner Filter
REF.NO.
5209O0
900
PART NO.
450255
450253
650867
350435650850
650939
510347
390322
650938410246A
410253
27261
650954
410277A
410280
570659610650B
550228
35977
550239
550247640901
590690
PART NAME
Air Cleaner FilterAir Cleaner CoverScrew, 10-24 x 1/2"BlowerHousing BaseScrew, 8-32 x 1-9/16"StudExhaust GasketMuffler (Incl. 274 & 277)Screw, 1/4-20 x 2.409"Fuel LineFuel Line ClampWasher
Locknut,8-32Fuel Tank (Incl.290,292, 298,301&370C)Fuel CapBlowerHousing PlugToggle SwitchInstructionDecalCaution DecalChoke DecalEmissionsDecal
Carburetor (Incl. 184)Rewind Starter &HousingAss'y.
Clutch (Supplied by OEM)Replacement engine 710580, orderfrom 71-999
Replacement S/B 710542B, orderfrom 71-999
CRAFTSMAN 2-CYCLE ENGINE MODEL NUMBER: 143.982070Starter No. 590690
12 @
6 3
,J I Ill_1' -
REFNO,
134568912
13
PARTNO.
590690650987
650985
650147
590691
590692_590693
590562590639
590452
PART NAME
Rewind Starter & HousingAss'y.Retainer Screw, 10-24 x 1-3/8"Pawl Screw, 12-24 x 11/64"WasherPawl SpringPawlPulleyRewind SpringStarter Rope (#4 rope, 71" long)Starter Handle
2O
For the repair or replacement parts youneed delivered directly to your homeCall 7 am-7 pm, 7 days a week1-800-366-PART(1-800-366-7278)Para ordenar piezas con entregaa domicilio -1-800-659-7084
For in-house major brand repair serviceCall 24 hours a day, 7 days a week1-800-4-REPAIR(1-800-473-7247)Para pedir servicio de reparaci6n adomicilio - 1-800-676-5811
For the location of a Sears Parts and
Repair Center in your areaCall 24 hours a day, 7 days a week1-800-488-1222
For information on purchasing a SearsMaintenance Agreement or to inquireabout an existing AgreementCall 9 am -5pm, Monday-Saturday1-800-827-6655
When requesting service or orderingparts, always provide the followinginformation:
• Product Type • Part Number• Model Number • Part Description
8#/AR8_e_'s RepairSpecialists
Printed In U.S.A.
Recommended