3B ES GCS Applications 1__ Menu System12-4

C en tr ilift

1Centrilift

The GCS Menu systemThe GCS Menu system

GCSModules

AnalogSetup &Display

SCADA &Security

& System

CustomUser

Screen

ProgLogicFunct

Faults&

Undld

Datalog&

History

GCSDriveSetup

StatusAnalog Setup

Screens used to calibrateand display measured analog

signals including Volts andAmps

GCS ModulesScreens used to enable,calibrate or scale built-ininputs, outputs & optional

external I/O modulesincluding Tracker

GCS Drive SetupMenu group contains most ofthe parameters that need tobe set and maintained for a

basic VSC installation

Datalog & HistorySection provides screens toaccess the historical data

and graphs that are recordedwithin the GCS controller

Faults & UnderloadMenus used to enable ordisable & adjust timing of

most conditions that causemotor shutdowns

SCADA, Security& System

Menus to enable securitypasswords, set real-timeclock & adjust telemetry

parameters

ProgrammableLogic FunctionsMenus used to access

standard control algorithmsand create customized

functions based on availableinputs and outputs

Custom UserScreen

Provides access tocustomized user display

screens

C en tr ilift

2Centrilift

GCS DRIVE SETUPGCS DRIVE SETUP

• The Contrast Adjust screen is accessed by pressing the left and right arrows at the same time.

C en tr ilift

3Centrilift

GCS DRIVE SETUPGCS DRIVE SETUP

• The Utility menu screen is accessed by pressing the up and down arrows at the same time.

Utility Menu

Set Frequency , 310

Add to Custom User 01Screen Capture 00Rename this Parameter

Replaces one of the two STATUSmenu parameters with the parameterabove

Add parm to status 01

C en tr ilift

4Centrilift

GCS DRIVE SETUPGCS DRIVE SETUP

• This screen allows you to rename any parameter

C en tr ilift

5Centrilift

GCS DRIVE SETUPGCS DRIVE SETUP

• The GCS Setup menus provide access to most of the parameters that need adjustment during routine setup and maintenance

C en tr ilift

6Centrilift

GCS DRIVE SETUP 1GCS DRIVE SETUP 1

GCS Setup 1• Most of the

application specific setpoints are found within these menus

• Factory default values based on drive model number

C en tr ilift

7Centrilift

GCS DRIVE SETUP 2GCS DRIVE SETUP 2

GCS Setup 2• Second setup

screen is accessed by the left or right arrow keys from GCS setup 1

C en tr ilift

8Centrilift

GCS DRIVE SETUP 2GCS DRIVE SETUP 2

GCS Setup 2• Scroll down when

more parameters than can be shown at one time.• User password

setpoint located here

C en tr ilift

9Centrilift

GCS DRIVE SETUP 2GCS DRIVE SETUP 2

GCS Setup 2• Frequency

Avoidance Submenu

• Any frequencies entered are active

C en tr ilift

10Centrilift

GCS DRIVE SETUP 3GCS DRIVE SETUP 3

GCS Setup 3• Torque Control

Setup Parameters• Only visible with

PCM8.xx and higher• Nameplate current &

Magnetizing current must be set

C en tr ilift

11Centrilift

GCS DRIVE SETUP 3GCS DRIVE SETUP 3

30 % of Nameplate30 % of Nameplate

Ft-Lbs= HP X 5252 3500

For ESP and ESPCP Motors

C en tr ilift

12Centrilift

GCS DRIVE SETUPGCS DRIVE SETUP

STARTS• Fourth screen of

GCS Drive Setup menu group

• Automatic restart parameters and time delays

C en tr ilift

13Centrilift

Datalog and History

• Accesses the recorded history stored within the GCS controller

• Includes screens for SHUTDOWN , RUNNING, EVENT HISTORY AND GRAPHING

C en tr ilift

14Centrilift

Datalog and History

Shutdown History• Records the

cause, date and time of last 99 shutdowns.

C en tr ilift

15Centrilift

Datalog and History

Shutdown Detail• Records a

“snapshot” of the volt, amp and analog measurements at shutdown

C en tr ilift

16Centrilift

Datalog and History

EVENT RECORDS

• Records all “events” that occur

• Events include: Start UpsSetpoint ChangesShutdowns

C en tr ilift

17Centrilift

Datalog and HistoryBFC BIT FIELD CHANGE (ONE BIT OF A STATUS WORD)

CFN CHANGE FROM NORMAL (POTENTIAL FAULT)

CNL CITIBUS NODE LOSS (SERIAL COMMUNICATION FAILURE)

CNR CITIBUS NODE RECOVERY (SERIAL COMMUNICATION RESTARTED)

EXC EXPONENT CHANGE

FDC FACTOR DEFAULT CHANGE (CHANGE OF INITIAL FACTORY SETTING)

IPL INITIAL PROGRAM LOAD (POWER UP)

MNC MINIMUM CHANGE

MXC MAXIMUM CHANGE

C en tr ilift

18Centrilift

Datalog and HistoryRTC REAL TIME CLOCK CHANGE

RTN RETURN TO NORMAL

SDE SHUT DOWN EVENT (STOP)

SPC SETPOINT CHANGE

SPR SETPOINT RELOAD (POWER UP)

SUE START UP EVENT

UNC UNITS CHANGE

UNE UNKNOWN ERROR

C en tr ilift

19Centrilift

Datalog and History

Running History• Accumulates

and records runtime statistics

C en tr ilift

20Centrilift

Datalog and History

Datalogging Setup

• Enables / Disables logging data to PC Card

• Entry to data log configuration screens

C en tr ilift

21Centrilift

Datalog and History

Graphing• GCS controller records

motor current for seven day period

• Minimum, Maximum and average current recorded every 1 min.

• Stored every week on memory card

C en tr ilift

22Centrilift

Datalog and History

Graphing• Graph time from 3hr

to 1 week• Choice of Graph

End, Graph Beginning, or Crsr for reference

C en tr ilift

23Centrilift

Datalog and HistoryPhase B amp

chart24 hrB Ampchart

0

80

Strt00/02/01

Crsr00/02/01

Min: 40Max: 45

][...................................................

C en tr ilift

24Centrilift

Datalog and History

Graphing (VORTEX GCS ONLY)

• Vortex GCS records 3 current and voltages at 600 samples/sec. for two seconds after startup

C en tr ilift

25Centrilift

Faults and AlarmsFaults and Alarms

• Access to system protection setpoints, thresholds and time delays

• Contents of menus vary depending on type of GCS controller

C en tr ilift

26Centrilift

Faults and AlarmsFaults and Alarms

Overload• Setpoint represents

the maximum amount of current allowed

• Highest amps is the maximum current on any phase

C en tr ilift

27Centrilift

Faults and AlarmsFaults and Alarms

1.5 2 2.5 3 3.5 40

1

2

3

4

P.U

. Tim

e

P.U. Current

Overload Trip Characteristics

C en tr ilift

28Centrilift

Faults and AlarmsFaults and Alarms

Aux Restart Parms• Use Instead of Global

Settings• Number of Restarts• Restart Delay

C en tr ilift

29Centrilift

Faults and AlarmsFaults and Alarms

Underload• Setpoint

represents the least amount of current allowed

C en tr ilift

30Centrilift

Faults and AlarmsFaults and Alarms

Input Over Voltage• Monitors maximum input

voltage• Customer scaleable input

voltages

C en tr ilift

31Centrilift

Faults and AlarmsFaults and Alarms

Input Under Voltage• Monitors minimum input

voltage• Customer scaleable input

voltages

C en tr ilift

32Centrilift

Faults and AlarmsFaults and Alarms

Input Voltage Unbal.• Monitors input voltage for

unbalance• Setpoint 0-100%

C en tr ilift

33Centrilift

Faults and AlarmsFaults and Alarms

Low Speed Trip• Protects against

operating the motor & pumping system below a safe running frequency

C en tr ilift

34Centrilift

Faults and AlarmsFaults and Alarms

Temperature Sensors

• The GCS Electrospeed has seven sensor inputs

• Shutdown thresholds are all factory set, except “auxiliary”

C en tr ilift

35Centrilift

Faults and AlarmsFaults and Alarms

Temperature Sensors• The auxiliary sensor

input can be used to measure the temperature of a users selected location

C en tr ilift

36Centrilift

Faults and AlarmsFaults and Alarms

Telemetry Fail• When enabled,

monitors loss of serial communication

C en tr ilift

37Centrilift

Faults and Alarms and Alarms

Alarm Setup• Provides a

convenient way to determine which alarms are enabled

• Use individual alarm screens to edit other parameters

C en tr ilift

38Centrilift

Programmable Logic Functions

• This menu group provides access to any available programmable functions

C en tr ilift

39Centrilift

Programmable Logic Functions

Programmable Function Setup

• Two programmable functions are included in basic drive

C en tr ilift

40Centrilift

Programmable Logic Functions

PID controller setup

• Proportional-Integral-Derivative closed loop control is a commonly used industrial algorithm

C en tr ilift

41Centrilift

Custom User Screen

Customer enters up to eleven parameters of particular interest

C en tr ilift

42Centrilift

Custom User Screen

Example of Custom User Screen

C en tr ilift

43Centrilift

SCADA & SECURITY & SCADA & SECURITY & SYSTEMSYSTEM

• Provides access to a variety of system maintenance, security, communications and time keeping functions

C en tr ilift

44Centrilift

SCADA & SECURITY & SCADA & SECURITY & SYSTEMSYSTEM

System• Reset setpoints &

prepares controller for re-deployment

• Some setpoints are not accessible in the field

C en tr ilift

45Centrilift

SCADA & SECURITY & SCADA & SECURITY & SYSTEMSYSTEM

SCADA Setup• This menu

screen allows the user to adjust the parameters controlling serial communications

C en tr ilift

46Centrilift

SCADA & SECURITY & SCADA & SECURITY & SYSTEMSYSTEM

Serial Com Diagnostic Screen• Receive Buffer• Transmit Buffer• Com stats

C en tr ilift

47Centrilift

SCADA & SECURITY & SCADA & SECURITY & SYSTEMSYSTEM

Provisions for three levels of password protection and security time out setting

C en tr ilift

48Centrilift

SCADA & SECURITY & SCADA & SECURITY & SYSTEMSYSTEM

Level 1: Start Stop Set Frequency Data Logging En. Resetable Run Time

Level 2:

Most Others

Code Enable:

Reset History Database

RTClock Alarm Enable

Security Level Access

C en tr ilift

49Centrilift

SCADA & SECURITY & SCADA & SECURITY & SYSTEMSYSTEM

Current Time• Menu displays the

present value of the onboard, real time, battery backed clock

C en tr ilift

50Centrilift

SCADA & SECURITY & SCADA & SECURITY & SYSTEMSYSTEM

Set Time• This screen is

used to edit and correct the setting of the real time clock

C en tr ilift

51Centrilift

Analog Setup & DisplayAnalog Setup & Display

• Access to the parameters related to the default analog measurements:

CurrentVoltagePower Factor

C en tr ilift

52Centrilift

Analog Setup & DisplayAnalog Setup & Display

Analog Setup• Electrospeed GCS is

factory calibrated for finite model ranges

• Vortex GCS allows the flexibility to accommodate a wide variety of load sizes

C en tr ilift

53Centrilift

GCS ModulesGCS Modules

• Access to calibration and setup of built-in general purpose analog & digital i/o

• Expansion modules are calibrated via these menus

C en tr ilift

54Centrilift

GCS ModulesGCS Modules• Onboard I/O is

built-in general purpose analog and digital inputs

• Expansion I/O cards will provide a simple method to expand any system

C en tr ilift

55Centrilift

GCS ModulesGCS Modules

• Status screen shows all detected slaves on CITIBus

C en tr ilift

56Centrilift

GCS ModulesGCS Modules

• Trident status screen if present

C en tr ilift

57Centrilift

GCS ModulesGCS Modules

Onboard I/O• Electrospeed and

Vortex GCS both provide two general purpose analog input channels

C en tr ilift

58Centrilift

GCS ModulesGCS Modules

Hi Threshold Setup• Similar to Fault Setup• Aux Restart Params

available

C en tr ilift

59Centrilift

GCS ModulesGCS Modules

Lo Threshold Setup• Similar to Fault Setup• Aux Restart Params

available

C en tr ilift

60Centrilift

GCS ModulesGCS Modules

Onboard I/O• Electrospeed GCS

has three general purpose digital (status) inputs

• Vortex GCS has two status inputs