View
24
Download
0
Category
Tags:
Preview:
Citation preview
www.taconic-add.com © Taconic 2012
The Influence of
RF Substrate Materials
on
Passive Intermodulation
(PIM)
Manfred Huschka, HKPCA 2012
www.taconic-add.com
2
What is Passive IM ?
• Passive Intermodulation Distortion
Created when two or more signals combine
to generate new frequency products
© Taconic 2012
www.taconic-add.com
3
Why do we care ?
• Nonlinearity of passive components
causes power at transmit frequencies to
mix into the system's receive band
Channels are blocked
Phone calls can be dropped
Reduced Capacity = Reduced Revenue !
© Taconic 2012
www.taconic-add.com
4
How is Passive IM Specified ?
• Absolute Power (dBm)
The Absolute IM Power (in dBm) of the
Intermodulation Signal
• Relative Power (dBc)
IM Signal Power relative to the Standard
Signal Carrier
Example : -110dBm IM signal generated by
two +43dBm tones is a –153dBc IM level
© Taconic 2012
www.taconic-add.com
5
How Is Passive IM Measured
• Multiple signals are injected to device
• High Power Amplifiers
• Highly Sensitive Receiver (LNA)
• Significant Filtering
+43dBm Tx Power
-140dBm Rx Noise Floor
…………….means 183dB Isolation !
© Taconic 2012
www.taconic-add.com
6
Putting it in Perspective
• Typically looking to measure
-110dBm or better with two +43dBm
carriers (-153dBc)
• In Linear Terms…
Distance to sun = 150,000,000 km
-153dBc equates to approx 0.07mm
© Taconic 2012
www.taconic-add.com
7
Typical PIM Causes
• Degradation Due to Environment
Contaminated conductors & Interfaces
(Dirt, Dust, Moisture)
Wind induced vibrations
Temperature cycles
• Semiconductor Junctions (Assembly)
Poor alignment of parts
Inadequately torqued screws & fasteners
Bad solder joints
© Taconic 2012
www.taconic-add.com
8
Typical PIM Causes
• Printed Circuits Boards
Processing issues
Laminate issues
© Taconic 2012
www.taconic-add.com
9
Typical PIM Causes
There are so many causes for PIM issues …
It is never related to one issue; it is usually a stacking of smaller issues …
Let us look at the influence of LAMINATES
© Taconic 2012
www.taconic-add.com
10
Laminates
• Not every laminate is suitable for antenna pcbs!
Tightly-controlled DK tolerance
Dissipation factor < Df 0.0025 for most grades @ 2GHz
Mature manufacturing technology
Lowest moisture absorption (<0.02%)
Bromine-free & RoHS compliant
Withstand >280°C assembly conditions; lead-free compatibility
© Taconic 2012
www.taconic-add.com © Taconic 2012
Low PIM Material Solutions
… for Base Station Antenna pcbs (phase shifter, power splitter, power combiner, filter)
Grade DK Df @ 2GHz
TLC-32 3.20 ± 0.05 0.0018
RF-30 3.00 ± 0.10 0.0013
RF-301 2.97 ± 0.05 0.0012
TLA-6 2.62 ± 0.05 0.0012
TLX-8 2.55 ± 0.04 0.0009
TLP-5 2.20 ± 0.02 0.0006
www.taconic-add.com
Copper Foil
© Taconic 2012
Copper foil is of huge influence on PIM
Copper foil
Copper Foil
PTFE Film
PTFE Film
Prepreg
Prepreg
Prepreg
Typical Laminate Construction:
www.taconic-add.com
Standard ED Foil
Additional plating process applied to “grow”
microcrystalline copper structure to
increase effective surface area.
“Drum” or “shiny” side
“Matte” or “treatment” side
Very Low Profile ED Copper Foil
© Taconic 2012
www.taconic-add.com
Copper treatment topography
(dendritic structure)
Rz DIN [micron]
C1 5 m-12 m
CL1 3-4 m
Rz is a measure of the roughness (or profile)
© Taconic 2012
Very Low Profile ED Copper Foil
www.taconic-add.com
VLP copper increases opportunity for
complete copper dendrite removal
Etching process is isotropic
“Cleaner/straighter” conductor side-walls
© Taconic 2012
Incomplete
etching
Very Low Profile ED Copper Foil
www.taconic-add.com
copper debris left in at the
bottom of the etched track
SEM Photo of Microstrip (C1 copper)
© Taconic 2012
www.taconic-add.com © Taconic 2007
Reverse Treatment Copper Foil
www.taconic-add.com © Taconic 2007
Reverse Treatment Copper Foil
www.taconic-add.com
CL1 copper shows
a lower surface
topography over the
plastic than C1
copper.
Note the “cleaner”
interface
Reverse Treatment Copper Foil
www.taconic-add.com © Taconic 2012
Attack from air and chemicals leading to underetching and discoloration (85°C/85% rh/200 h)
Surface Protection
www.taconic-add.com © Taconic 2012
Solder Mask leads to protection of side wall from air and chemicals
Surface Protection
www.taconic-add.com
Influence of protective coating
Source: Powerwave
f1 f2 IM frequency
960 MHz 927.5 MHz 895 MHz
960 MHz 932.5 MHz 905 MHz
960 MHz 937.5 MHz 915 MHz
Frequency for measurements
© Taconic 2012
PIM [dBm]
Surface Protection
Max (fwd)
Min (fwd)
Max (bwd)
Min (bwd)
Immersion Tin 1.0 micron -114 -126.5 -113.5 -124.5
OSP 0.3 micron -92.2 -96.5 -99.5 -112.6
Immersion Silver
0.2 - 0.8 micron
-81.5 -92.5 -94.5 -108.6
ENIG 0.05 - 0.1 micron Au/ 3-5 micron Ni
-50.5 -53.5 -58.5 -61.5
HASL 3-25 micron -103.9 -123 -112.3 -123.8
www.taconic-add.com
Low PIM Laminate Solutions
Selecting the most suitable laminate
together with the most suitable copper foil
ensures that the most critical variables of
influence upon Passive Intermodulation are
met.
During pcb manufacturing process many more
critical variables have to get addressed …
© Taconic 2012
Taconic is here to support your needs!!
Recommended