1 At-Grade Intersection Design. 2 Objectives Define general intersection design objectives Describe...

1

At-Grade Intersection Design

2

Objectives

Define general intersection design objectives

Describe factors that influence curb return design

For a nice overview of intersection design, see http://www.fhwa.dot.gov/environment/flex/ch08.htm

3

Intersections

Grade-separated without ramps Interchanges (grade separated with

ramps) At-grade

4

Intersection – Design Controls• Primary controls:

• Functional class of roadways

• Topography and environment (manmade and natural)

• Secondary controls:• Design speed

• Design vehicles

• Traffic Characteristics (design volumes, level of service)

5

Intersection Design Elements/Considerations

4 or fewer legs (within functional area) As close to 90 degrees as possible Approach (flat and straight as possible)

• Avoid > 6% on low speed (< 40 mph) and > 3% on high speed (≥ 50 mph)

Provide min. grades and max. vertical curve lengths

6

Intersection Design Elements/Considerations

Continue grade throughout the intersection Make adjustments away from intersection Traffic lanes should be visible and obvious to

motorists Motorists should understand the path they are

supposed to take Horizontal and vertical alignment should facilitate

frequent braking

7

Types of Intersection 4-leg T-intersection 5 or more legs Traffic circles

• Rotaries: large diameter > 300 ft, allows speeds > 30 mph with minimum horizontal deflection of the path of through traffic

• Neighborhood traffic circle: small diameter, for local streets, traffic calming

• Roundabout• Yield control at each approach

• Separation of conflicting movements

• Speed < 30 mph (typically)

8

Basic Principles

Minimize severity of potential conflicts Provide for smooth flow of traffic Consider both vehicles and pedestrians

9

Elements of Design

Design of alignment Design of channeling system Determination of minimum required

widths of turning roadways • Speeds > 15 mph

Intersection sight distance Determination of number of lanes

• Provision of turning lanes

10

Alignment Horizontal

90° intersection of approaches

Skewed• Visibility

• Longer crossing times in some cases

11

Profile (Vertical)

Should facilitate driver’s control of vehicle

Avoid significant changes in grade Typically ≤ 3% Continue major street grade through

intersection

12

Curb Radius

Factors of influence:

• Design vehicle

• Intersection angle

• Approach width and parking

• Channelization

• Pedestrians

• Allowable speed reduction

13

Curb Radius Green Book Minimums assume:

• Turning Speed LTE 10 mph

• Vehicle properly positioned beginning and end

• Vehicle doesn’t cross inner edge of pavement

14

Design Vehicle

Source: www\fhwa\Flexibility in Highway Design - Chapter 8 - FHWA.htm

15

Radius Design

• Simple curve

•Low speed collector, local streets

• Simple circle with taper• 3-centered compound curve

16

Minimize lane encroachment

R = 15 feet

17

Simple Curve (passenger car template)

18

Simple Curve with Taper (passenger car template)

19

Compound curves (passenger car template)

20

21

22

Curb Radius

General Guidance

•10 to 25 ft. local

•25 to 30 ft. collectors

•30 to 35 ft. unchannelized intersections with arterials

23

Source: www\fhwa\Flexibility in Highway Design - Chapter 8 - FHWA.htm

24

High Speed Turns

25

Channelization

Separates conflicting movements into definite paths of travel

Uses pavement markings or traffic islands Directs vehicle paths so no more than 2

paths cross at one point Controls merging, diverging, and crossing

angle of vehicles Decreases vehicle wander

26

Channelization

Provides clear path for different movements

Gives priority to dominant movements Provides pedestrian refuge Provides storage area for turning vehicles Controls prohibited turns Restricts speed

27

Types of Channelization

Raised islands• Urban

• Provides refuge for pedestrians

• <= 50 ft2 in urban areas

• <= 75 ft2 in rural areas Pavement markings

• Low pedestrian volume, low approach speeds

28

Types of Channelization

Pavement edge• Rural – painted if high speed• Formed by diverging through and right turn

lanes

29

Delineation With Pavement Marking

30

Left & Right Turn Lane Warrants

Turning movement volumes

Accident experience

Capacity

Source: www\fhwa\Flexibility in Highway Design - Chapter 8 - FHWA.htm

31

Left & Right Turn Lane Design Number of likely queued vehicles

• Type of control

• Number of turning vehicles

• Length of vehicles

32

Deceleration Lanes

Provides distance for turning vehicles to decelerate away without interfering with through traffic

Deceleration lane length depends on:• Speed

• number of queued vehicles

• vehicle length

33

Median Openings …(see GB for Design specs)

34

Intersection Design Considerations for

Pedestrians

35

36

Provide median refuge to provide crossing in stages

37

Provision of crosswalks

38

Intersections on High Speed Rural Divided Expressways

39

40

41