View
13
Download
0
Category
Tags:
Preview:
Citation preview
0
Procelerant CE3100 BIOS Setup Utility Specification
www.radisys.com 002-06875-0000
Copyright © 2007 by RadiSys Technology (Ireland) Ltd. All rights reserved. RadiSys is a registered trademark and Procelerant is a trademark of RadiSys Corporation. All other trademarks, registered trademarks, service marks, and trade names are the property of their respective owners.
Revision History
Revision History
Revision Date Description
-0000 September, 2007 First release.
Page 2 of 39
Table of Contents
Table of Contents
1. BIOS Setup Utility Overview ----------------------------------------------------------------------------------------------------4
1.1 Menu map ------------------------------------------------------------------------------------------------------------------4 1.2 Keyboard commands ----------------------------------------------------------------------------------------------------5
1.2.1 General Help ------------------------------------------------------------------------------------------------------------5 1.3 User interface design ----------------------------------------------------------------------------------------------------6
1.3.1 Definitions of BIOS item types--------------------------------------------------------------------------------------6 1.3.2 Sorting orders of BIOS items and available options ----------------------------------------------------------6 1.3.3 Active fields--------------------------------------------------------------------------------------------------------------6 1.3.4 Read-only settings-----------------------------------------------------------------------------------------------------6 1.3.5 Invisible settings--------------------------------------------------------------------------------------------------------6 1.3.6 Symbolic indicators----------------------------------------------------------------------------------------------------6
2. Main Menu---------------------------------------------------------------------------------------------------------------------------7 3. Information Menu ------------------------------------------------------------------------------------------------------------------8
3.1 Version Information ------------------------------------------------------------------------------------------------------9 3.2 System Monitors -------------------------------------------------------------------------------------------------------- 10
4. Configuration Menu ------------------------------------------------------------------------------------------------------------- 11 4.1 SATA Configuration ---------------------------------------------------------------------------------------------------- 13 4.2 USB Configuration------------------------------------------------------------------------------------------------------ 15 4.3 LAN Configuration ------------------------------------------------------------------------------------------------------ 16 4.4 PCI Expansion Slot Configuration ---------------------------------------------------------------------------------- 17 4.5 Power Control Configuration----------------------------------------------------------------------------------------- 19 4.6 Security Configuration ------------------------------------------------------------------------------------------------- 21 4.7 CPU Configuration ----------------------------------------------------------------------------------------------------- 22 4.8 Advanced Configuration ---------------------------------------------------------------------------------------------- 24
4.8.1 DMI Event Logging -------------------------------------------------------------------------------------------------- 27 4.8.2 Legacy Device Configuration ------------------------------------------------------------------------------------- 29
5. Boot Menu ------------------------------------------------------------------------------------------------------------------------- 33 5.1 Boot Order---------------------------------------------------------------------------------------------------------------- 35
6. Exit menu -------------------------------------------------------------------------------------------------------------------------- 36 6.1 Exit menu for Standard BIOS and Full BIOS -------------------------------------------------------------------- 36 6.2 Exit menu for SCM BIOS --------------------------------------------------------------------------------------------- 38
Page 3 of 39
BIOS Setup Utility Overview
1. BIOS Setup Utility Overview This specification introduces the three BIOS definitions for the Procelerant CE3100 COM Express module:
▪ Standard BIOS. This BIOS supports the functions of CE3100 COM Express modules, and can boot from any custom carrier board that uses COM Express type 3 pinouts. This BIOS may not support all features of the custom carrier board, especially if it contains legacy interfaces.
▪ Full BIOS. This BIOS supports all available features when a CE3100 COM Express module is used with the CR200-VGA ATX carrier board.
▪ SCM BIOS. This BIOS supports the operation when a CE3100 COM Express module is used with the Promentum ATCA-2210 Switch And Control Module (SCM).
The three BIOS definitions are based on the standard Phoenix® TrustedCore™ with RadiSys extensions. A BIOS setup utility is included to display and modify system configuration. The BIOS configuration information is stored in nonvolatile CMOS RAM and is used to initialize the system.
To access to the BIOS setup utility, press F2 during POST when the system boots up. This provides consistency of operation across all supported operating systems, and forces a direct correspondence between the hardware and BIOS settings.
1.1 Menu map Figure 1 shows the menu map of the BIOS setup utility. Each menu is equivalent to a functional group and comprises of all correlated BIOS settings.
Note: The CE3100 BIOS provides an interface to detect carrier board configuration serial EEPROM based on CE3100’s supported features. When the carrier board serial EEPROM is also supported on the carrier board, menu options in the BIOS setup utility may vary depending on EEPROM contents.
Figure 1. Menu map
c M a in I n f o r m a t io n B o o t E x i t
M a in M e n u
I n f o r m a t io n M e n u
B o o t M e n u
E x i t M e n u
U S B C o n f ig u ra t io n
L A N C o n f ig u r a t io n
V e r s io n I n f o r m a t io n
b
C o n f ig u r a t io n M e n u
C o n f ig u r a t io n
S y s t e m M o n i t o r s I n f o r m a t io n
P C I E x p a n s io n S lo t C o n f ig u r a t io n
P o w e r C o n t r o l C o n f ig u r a t io n
S e c u r i t y C o n f ig u r a t io n
C P U C o n f ig u r a t io n
A d v a n c e d C o n f ig u r a t io n
S A T A C o n f ig u r a t io n
Page 4 of 39
BIOS Setup Utility Overview
1.2 Keyboard commands In the BIOS setup utility, a legend at the bottom of each screen provides instructions for manipulating setup options, as shown in Table 1.
Table 1. Keyboard commands
Keyboard Commands Function Design
F1 Help Press F1 to view help information.
← → Select Menu Press ← and → keys to navigate to a specific menu.
↑↓ Select Item Press ↑ and ↓ keys to navigate to a specific field within a menu.
–/+ Change Values Press – and + keys to step through available options.
Enter Select Entry Press Enter to display a submenu or select an option.
Esc Exit Press Esc to exit the BIOS setup utility.
F9 Setup Defaults Press F9 to revert all BIOS fields to setup defaults.
F10 Save and Exit Press F10 to save your changes and exit the BIOS setup utility.
1.2.1 General Help
When pressing F1 or Alt + H in the BIOS setup utility, the General Help should display the following literal texts:
Different BIOS configurations can change the system behavior. If incorrect values cause the system boot failure, load the defaults to recover.
<Up/Down> arrows select fields in the current menu.
<PgUp/PgDn> moves to previous/next page on a scrollable menu.
<Home/End>moves to top/bottom item in the current menu.
Within an item, <F5> or <-> selects the preceding option and <F6>, <+>, or <Space> selects the next option.
<Left/Right> arrows select menus on the menu bar.
<Enter> displays sub-items for the item marked with ►.
<F9> loads setup defaults.
<F10> saves current settings and exits.
<Esc> or <Alt-X> exits a submenu and returns to the parent menu.
<F1> or <Alt-H> displays General Help (this screen).
Page 5 of 39
BIOS Setup Utility Overview
1.3 User interface design 1.3.1 Definitions of BIOS item types
According to function design considerations, each BIOS item should be addressed with one of the following types:
▪ User entry
▪ Read-only
▪ Executable command
▪ Submenu
1.3.2 Sorting orders of BIOS items and available options
▪ The sorting order of all BIOS settings on each setup screen shall match the screen mockups in the sections that follow. It may follow a logical order, or alphabetical order where the logical order of grouped settings is not important.
▪ The sorting order of all available options under each BIOS item shall always follow an alphabetical order.
1.3.3 Active fields
▪ An active field exists only when a BIOS item comprises of more than one available option. A read-only setting will never preserve active fields.
▪ The currently selected option in an active field should be highlighted.
▪ When a setup screen is displayed, the cursor always pauses at the first selectable field.
▪ When the user returns to a previously visited menu by pressing any of the up, down, left, and right arrow keys, the active field is always the first selectable field.
1.3.4 Read-only settings
The read-only settings include:
▪ A setting that is used to display the system output.
▪ A setting that identifies the input information for the system, but there is only one available option. This occurs when this information is important and must be made visible to users.
Read-only BIOS settings cannot be selected in the BIOS setup utility. When the user navigates through BIOS settings by pressing any of the up, down, left, and right arrow keys, the BIOS will leap over read-only settings.
1.3.5 Invisible settings
The invisible settings include:
▪ A setting that is designed for test purpose only. This type of invisible settings should be generally limited.
▪ A setting that is essential to the product and the user’s knowledge base, and does not need any user interference.
1.3.6 Symbolic indicators
1.3.6.1 I/O resource conflicts
In most cases the BIOS can automatically detect all possible conflicts. Once a BIOS setting being specified causes an I/O resource conflict, a yellow star appears to the left of the device name as seen under the operating system.
Such resource conflicts will be manually intervened and resolved under the operating system according to operating environment and system requirements.
Page 6 of 39
Main Menu
2. Main Menu
Figure 2. Main menu
Phoenix B IO S Setup U tility
M ain Inform ation Configuration Boot Exit
F1 Help ↑↓ Select Item +/– Change Value F9 Setup DefaultsESC Exit ←→ Select M enu Enter Select Entry F10 Save and Exit
Item Specific Help
System T im e: [00:00:00] System Date: [01/01/2007] CPU Type: Intel (R ) Pentium (R) M CPU Speed: 1733M Hz System M em ory: 640 KB Extended M em ory: 1014 M B
The fields in each menu and submenu are explained below. Additional help information is available in the help area on the Setup screen.
BIOS Item Function Design Item Specific Help
System Time User entry. The default is 00:00:00. Specify the current time (HH: MM: SS, 24-hour clock notation). Press Tab, Shift+Tab, or Enter to select fields.
System Date User entry. The default is 01-01-2007.
Specify the current date (mm/dd/yyyy). Press Tab, Shift+Tab, or Enter to select fields.
CPU Type Read-only. Displays the CPU vendor and type.
N/A
CPU Speed Read-only. Displays the CPU speed in MHz.
N/A
System Memory Read-only. Displays the amount of conventional memory (below 1MB).
N/A
Extended Memory Read-only. Displays the amount of extended memory (above 1MB).
N/A
Page 7 of 39
Information Menu
3. Information Menu
Figure 3. Information menu
Phoenix BIOS Setup Utility
Main Information Configuration Boot Exit
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help 4Version Information 4System Monitors
BIOS Item Function Design Item Specific Help
Version Information A submenu that includes a varied list of basic BIOS information. The basic BIOS information shown is read-only and depends on the version of BIOS releases. See 3.1.
Display the BIOS version information.
System Monitors A submenu that includes a list of system temperatures and fan speeds. The information shown is read-only.
Display the system temperature readings and fan speeds.
Page 8 of 39
Information Menu
3.1 Version Information
Figure 4. Version Information
Phoenix BIOS Setup Utility
Information
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
Version Information Main BIOS: 0.7.00.00 BIOS Build Stamp: 04/11/07 16:45:40 Boot Block: 07.00.00
BIOS Item Function Design Item Specific Help
Main BIOS BIOS Build Stamp Boot Block
Read-only. The three version numbers specify the build of the BIOS. The versions do not reflect any customized features: - The Main BIOS field shows the principle revision of the main BIOS. - The BIOS Build Stamp field shows the date and time when the BIOS image was built. - The Boot Block field shows the version of the BIOS boot block. It is updated less frequently than the main BIOS.
Consult your system supervisor if changes are required.
Page 9 of 39
Information Menu
3.2 System Monitors
Figure 5. System Monitors
Phoenix BIOS Setup Utility
Information
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
System Monitors Processor Fan Speed 6398 RPM System Fan 1 Speed Not Detected System Fan 2 Speed Not Detected Processor Temperature (DTS) 39ºC COM-E Board Temperature 35ºC Carrier Board Temperature 30ºC
BIOS Item Function Design Item Specific Help
Processor Fan Speed
Read-only. This item is visible only in the Full BIOS. This number identifies the speed of the processor fan in revolutions per minute. When no processor fan is detected, “Not Detected” is displayed.
System Fan 1 Speed
Read-only. This item is visible only in the Full BIOS. This number identifies the speed of the system fan 1 in revolutions per minute. When no processor fan is detected, “Not Detected” is displayed.
System Fan 2 Speed
Read-only. This item is visible only in the Full BIOS. This number identifies the speed of the system fan 2 in revolutions per minute. When no processor fan is detected, “Not Detected” is displayed.
Consult your system supervisor if changes are required.
Page 10 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
Processor Temperature
Read-only. The temperature of the processor is detected by the CPU digital thermal sensor (DTS).
COM-E Board Temperature
Read-only. The temperature of the COM Express module is detected by the onboard thermal sensor.
Carrier Board Temperature
Read-only. This item is visible only in the Full BIOS. The temperature of the COM Express carrier board is detected by the onboard thermal sensor.
4. Configuration Menu Figure 6. Configuration menu
Phoenix BIOS Setup Utility
Main Information Configuration Boot Exit
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
4SATA Configuration 4USB Configuration 4LAN Configuration 4PCI Expansion Slot Configuration 4Power Control Configuration 4Security Configuration 4CPU Configuration 4Advanced Configuration
BIOS Item Function Design Item Specific Help
SATA Configuration A submenu that includes a list of items to configure SATA devices. This item and its sub-items will be hidden when the SAS controller is on the module. Note: If the SAS controller is present on the module, to configure SAS function, the user will need to press Ctrl + C to enter the SAS Option ROM during system POST
Configure SATA devices.
Page 11 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
USB Configuration A submenu that includes a list of items to configure USB controllers, UHCI and EHCI.
Configure USB controllers.
LAN Configuration A submenu that includes a list of items to configure an onboard dual-port LAN device. The LAN signals come from one x4 PCI Express bridge.
Configure onboard LAN devices.
PCI Expansion Slot Configuration
A submenu that includes a list of items to configure the IICH’s PCI expansion slot.
Configure PCI expansion slots.
Power Control Configuration
A submenu that includes a list of items to configure system power options.
Configure the system power.
Security Configuration
A submenu that includes a list of items to configure system security options.
Configure the system security.
CPU Configuration A submenu that includes a list of items to configure CPU control options.
Configure the CPU control.
Advanced Configuration
A submenu that includes a list of items to configure advanced system options.
Configure the advanced system settings.
Page 12 of 39
Configuration Menu
4.1 SATA Configuration The SATA Configuration menu and all items included are hidden when the SAS controller is present on the module.
Figure 7. SATA Configuration
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help .
SATA Configuration
Serial ATA: [Enabled] SATA Controller Mode: [Compatible] AHCI Configuration: [Disabled]
BIOS Item Function Design Item Specific Help
Serial ATA Available options are: - Disabled: If selected, all items below will be hidden. - Enabled (default)
Select Enabled to support SATA devices.
SATA Operation Mode
Available options are: - Compatible: SATA and PATA drives are automatically detected and placed in legacy mode. - Enhanced (non-AHCI): SATA and PATA drives are automatically detected and placed in native IDE mode.
Current disk drives typically operate better in Enhanced mode. Select Compatible if using a legacy disk drive.
AHCI Configuration This item is available only when SATA Controller Mode is set to Enhanced. Available options are: - Disabled (default) - Enabled
Select Enabled to support the native PCI AHCI controller using Intel Matrix Storage Manager for improved ATA data transfer performance. When disabled, the native PCI IDE controller is supported with standard IDE drivers.
Page 13 of 39
Configuration Menu
Page 14 of 39
Configuration Menu
4.2 USB Configuration
Figure 8. USB Configuration
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
USB Configuration USB Functions: [Enabled]
USB 2.0 Support: [Enabled] Legacy USB Support: [Enabled]
BIOS Item Function Design Item Specific Help
USB Functions Available options are: - Disabled Two Ports: Enable UHCI controller 0, ports 0 through 1 Four Ports (default): Enable UHCI controllers 0 and 1, ports 0 through 3
For locations of each USB port, refer to the Product Manual.
USB 2.0 Support This item is visible only when USB Functions is not set to Disabled. Available options are: - Disabled - Enabled (default)
Select Enabled to support USB 2.0 functionality for all USB ports.
Legacy USB Support
Available options are: - Disabled - Enabled (default)
Select Enabled to support a USB keyboard and mouse under DOS.
Page 15 of 39
Configuration Menu
4.3 LAN Configuration
Figure 9. LAN Configuration
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
LAN Configuration Onboard LAN Port 0: [Enabled] MAC Address: Onboard LAN Port 1: [Enabled] MAC Address: PXE Option ROM: [Enabled] Power Saving When S5: [Disabled]
BIOS Item Function Design Item Specific Help
Onboard LAN Port 0
Available options are: - Disabled - Enabled (default): If selected, the MAC address of this port will be displayed below.
Enable or disable LAN port 0. Note: When disabled, LAN port 1 will use the MAC address of port 0.
MAC Address Read-only. Displays the Ethernet node address assigned to port 0 by the dual Gigabit Ethernet controller.
N/A
Onboard LAN Port 1
Available options are: - Disabled - Enabled (default): If selected, the MAC address of this port will be displayed below.
Enable or disable LAN port 1.
MAC Address Read-only. Displays the Ethernet node address assigned to port 1 by the dual Gigabit Ethernet controller.
N/A
PXE Option ROM Available options are: - Disabled: The option ROM will not be loaded during system boot. - Enabled (default): The option ROM will be loaded during system boot.
Select Enabled to load the onboard LAN Option ROM during system boot for PXE support.
Page 16 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
Power Saving When S5
Available options are: - Disabled (default) - Enabled: If selected, the system allows the Ethernet controller chip to power off the LAN in the S5 (Soft Off) state. Consequently, the Wake On LAN is unavailable.
Select Enabled to power off the LAN in the S5 (Soft Off) state. This will make Wake On LAN unavailable.
4.4 PCI Expansion Slot Configuration
Figure 10. PCI Expansion Slot Configuration
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
PCI Expansion Slot Configuration PCI Express – Root Port B0: [Enabled] PCI Express – Root Port B1: [Enabled] PCI Express – Root Port B2: [Enabled] PCI Express – Root Port B3: [Enabled]
Page 17 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
PCI Express –Root Port B
This item is visible only when the x4 PCI Express slot is configured as one x4 PCI Express interface, instead of the four x1 PCI Express interfaces. In this case, all BIOS items beneath this item are invisible. The Intel 3100 chipset IICH supports one x4 PCI Express interface (PEB). Available options are: - Disabled - Enabled (default)
Select Disabled if the PCI Express x4 (PEB) interface functionality is not required.
PCI Express - Root Port B0 PCI Express - Root Port B1 PCI Express - Root Port B2 PCI Express - Root Port B3
This item is visible only when the x4 PCI Express slot is configured as the four x1 PCI Express interfaces. The CE3100 module provides a switch to configure the interface as either one x4 PCI Express interface or four x1 PCI Express interfaces. When the PEB functions as a single x4 PCI Express interface, all root ports cannot be disabled, otherwise the functionality will fail. This item is designed to configure x1 PCI Express devices when the PEB is configured as four x1 PCI Express interfaces. Available options are: - Disabled - Enabled (default)
When the x4 PCI Express slot (PEB) is configured as four x1 PCI Express interfaces, enable or disable each of them. When Root Port 0 is disabled, all other ports will also be disabled.
Page 18 of 39
Configuration Menu
4.5 Power Control Configuration
Figure 11. Power Control Configuration
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
Power Control Configuration RTC Wake-Up: [Off] Wake-Up Time: [00:00:00] After Power Failure: [Power On] PME Wake from S5: [Disabled]
BIOS Item Function Design Item Specific Help
RTC Wake-Up Available options are: - Off (default) - On
Select On to wake up the system at the time specified in the Wake-Up Time setting.
Wake-Up Time User entry. The default is 00:00:00.Note: This setting will function only when RTC Wake-Up is set to On.
Specify the time (HH:MM:SS, 24-hour clock notation) when the system is to wake up. Press Tab, Shift + Tab, or Enter to select fields.
Page 19 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
After Power Failure In the Standard BIOS and Full BIOS, this item is visible with these available options: - Last State: The system reverts to the previous power state before AC power is lost. - Power On: The system powers up immediately after AC power is restored. - Stay Off: The system remains powered-off until the power switch is pressed. In the SCM BIOS, this item is invisible. But the system will always power up immediately after AC power is restored.
Specify the action when power is restored after AC power loss.
PME Wake from S5 Available options are: - Disabled (default): The system cannot be woken using the PME signal. - Enabled: The system may be woken from S5 state (Soft Off) using the PME signal.
Select Enabled to allow the PCI power management event signal to wake up the system from the S5 (Soft Off) state.
Page 20 of 39
Configuration Menu
4.6 Security Configuration
Figure 12. Security Configuration
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
Security Configuration Set Supervisor Password: [Enter] Set User Password: [Enter] Password on Boot: [Disabled]
BIOS Item Function Design Item Specific Help
Set Supervisor Password
User entry. The supervisor password controls full access to both fundamental and advanced configuration items.
Press Enter to specify a supervisor password for full control. The password is not case-sensitive and permits a maximum of 8 numbers, letters, special characters (including \ [ ] ; ‘ , . /), and spaces.
Set User Password User entry. This item will be available to enter a normal user password only when the supervisor password is not blank, otherwise, it will be grayed out. A normal user password allows users to log in the BIOS setup utility and configure fundamental configurations. Without in-depth knowledge of the system, changes to advanced configuration items may cause serious hardware problems and fatal system errors. This password will restrict access to advanced configuration items.
Press Enter to specify a password for normal users to configure fundamental configuration items. The password is not case-sensitive and permits a maximum of 8 numbers, letters, special characters (including \ [ ] ; ‘ , . /), and spaces.
Page 21 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
Password on Boot Available options are: - Disabled (default): A password is not required to complete the boot. - Enabled: Ether the supervisor or the user password, where configured, is required to complete the boot process.
Specify whether a password is required to complete the boot process. If enabled, either the supervisor or user password can be used.
4.7 CPU Configuration
Figure 13. CPU Configuration
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
CPU Configuration
Core Multi-Processing: [Enabled] Processor Power Management: [Disabled] VT Feature: [Enabled]
BIOS Item Function Design Item Specific Help
Core Multi-Processing
This item is visible only when the module’s processor is dual core. Available options are: - Disabled: This option will disable one execution core of the processor. - Enabled (default)
Select Disabled if dual core processing is not required.
Page 22 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
Processor Power Management
Available options are: - C States Only: The processor power will be controlled through CPU power states in the ACPI setting. - GV1/GV3 Only: This enhanced Intel(R) SpeedStep(TM) (known as GV3) will dynamically adjust the clock speed and automatically switch between maximum performance mode and battery-optimized mode depending on the needs of application operation. - Disabled: No processor power management will be performed. - Enabled (default): Both C States and GV1/GV3 will be enabled.
Processor power management deserves special attention to conserve battery power, extend processor life and reduce noises from cooling apparatus, especially on a mobile system. Select Enabled to support both C states and GV1/GV3.
VT Feature This item may be invisible depending on the processor support. The Intel(R) Virtualization Technology is formerly known as Vanderpool Technology. Functionality, performance and other benefits will vary depending on hardware and software configurations. Available options are: - Disabled (default) - Enabled
Select Enabled to support the Intel(R) Virtualization Technology. Using the Virtual Machine Monitor (VMM) or corresponding software, a CPU will act as if it were several CPUs working in parallel, in order to enable several operating systems to run at the same time in the same machine.
Page 23 of 39
Configuration Menu
4.8 Advanced Configuration
Figure 14. Advanced Configuration
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
Advanced Configuration Reset Configuration Data: [No] HPET Support: [Disabled] Clock Spread Spectrum: [Disabled] Route Port 80h Cycles to: [LPC] Onboard Serial Port: [Enabled] Base I/O Address: [3F8] Interrupt: [IRQ 10] Console Redirection [Disabled] Baud Rate [115200]
Console Type [PC ANSI] Continue C.R. after POST [Off]
4DMI Event Logging 4Legacy Device Configuration
BIOS Item Function Design Item Specific Help
Reset Configuration Data
Available options are: - Yes: Reset the configuration data. The operating system should load normally after system reboot. The selection reverts to [No] in the next boot cycle. - No (default): Do not reset the configuration data.
Select Yes to clear the Extended System Configuration Data (ESCD) held in the flash ROM and to reconfigure the settings. If the BIOS cannot detect hardware changes, this setting helps solve resource conflicts. This setting always reverts to No after system reboot.
HPET Support Available options are: - Disabled - Enabled (default): The RSDT (Root System Description Table) will point to the HPET (High Precision Event Timer), and the appropriate enable bits will be set.
Enable or disable the support for the High Precision Event Timer.
Page 24 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
Clock Spread Spectrum
Available options are: - Off (default) - On
Select On to enable the system’s spread spectrum to reduce EMI.
Route Port 80H Cycles to
Available options are: - LPC (default) - PCI
Select where the Port 80h cycles are sent.
Onboard Serial Port This item, together with all the related settings beneath this item, is visible only in the Standard BIOS. The serial port controlled by this item is the RS-232 port on the module, which is on the header for BIOS recovery, clearing CMOS, and RS-232 port. Available options are: - Disabled - Enabled (default)
Configure the onboard serial port. The header for BIOS recovery, clearing CMOS, and RS-232 port provide 3 pins to support RS-232 serial port.
Base I/O Address Read-only. This item is visible only when the onboard serial port is enabled. The fixed value of this base I/O address is 3F8.
N/A
Interrupt Read-only. This item is visible only when the onboard serial port is enabled. The fixed value of this interrupt is IRQ 10.
N/A
Console Redirection
This item, together with all the related settings beneath this item is visible only in the Standard BIOS. This item is used to configure the console redirection for this onboard serial port. Note: When this item is disabled, all the related settings beneath this item invisible. Available options are: - Disabled - Enabled (default)
Enable or disable the console redirection for this onboard serial port,
Page 25 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
Baud Rate Available options are: - 300 - 1200 - 2400 - 9600 - 19.2K - 38.4K - 57.6K - 115.2K (default)
Check the baud rate supported by your device, and select the same or compliant baud rate here.
Console Type Available options are: - VT100 - VT100 8Bit - PC ANSI 7Bit - PC ANSI - VT100+ (default) - VT-UTF8 - ASCII
Check the console protocol supported by your device, and select the same console protocol Here.
Continue C.R. after POST
Available options are: - Off - On (default)
Select On to enable console redirection after entering the operating system.
DMI Event Logging A submenu that includes a list of items used to view and manage the DMI event logs. See 4.8.1.
View and manage DMI (Desktop Management Interface) event logs.
Legacy Device Configuration
A submenu that includes a list of items used to configure legacy Super I/O devices. This item is visible only in the Full BIOS and/or SCM BIOS. See 4.8.2.
Configure legacy devices in Super I/O mode.
Page 26 of 39
Configuration Menu
4.8.1 DMI Event Logging
Figure 15. DMI Event Logging
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
DMI Event Logging Event Log Validity Event Log Capacity Event Logging: [Enabled] View DMI Event Log: [Enter] Mark DMI Events as Read: [Enter] Clear all DMI Event Logs: [No]
BIOS Item Function Design Item Specific Help
Event Log Validity Read-only. The system will detect whether the DMI event logging completes successfully. The default depends on the results of the system detection. Possible results are: - Not Valid - Valid
N/A
Event Log Capacity Read-only. The DMI event logs are stored in the ESCD. The default depends on whether the allocated ESCD space is full of DMI event logs. Possible results are: - Full - Space Available
N/A
Page 27 of 39
Configuration Menu
BIOS Item Function Design Item Specific Help
View DMI Event Log
A prompt window will display all the DMI events. One of the following three possible scenarios may be displayed in this window: - No event log records found - No unread events - The information of unread event logs is displayed. This window provides a Continue button. Press Enter to close the window and to go back to the DMI Event Logging screen.
Press Enter to view all the current unread DMI event logs.
Event Logging Available options are: - Disabled - Enabled (default)
Select Enabled to allow logging of DMI events.
Mark DMI Events as Read
When there are no DMI event logs or all logs have been marked as read, this item will be grayed out.
Press Enter to mark all DMI events in the event log as read.
Clear All DMI Event Logs
Available options are: - No (default) - Yes
Select Yes to clear all DMI event logs after reboot.
Page 28 of 39
Configuration Menu
4.8.2 Legacy Device Configuration
Note: This submenu, together with all the following BIOS items, is visible only in the Full BIOS and/or SCM BIOS.
PhoenixBIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
Legacy Device Configuration
Serial Port A [Enabled] Base IO Address [3F8]
Interrupt [IRQ 4] Serial Port B [Enabled] Base IO Address [2F8]
Interrupt [IRQ 3] Parallel Port [Enabled] Mode [ECP] Floppy Disk Controller [Enabled]
Console Redirection [Disabled] Baud Rate [19.2K] Console Type [PC ANSI] Flow Control [None] Console Connection [Direct] Continue C.R. after POST [Off]
Item Description Item Specific Help
Serial Port A This item is used to configure the Super I/O-based serial port A. In the Standard BIOS and Full BIOS, available options are: - Disabled - Enabled (default) In the SCM BIOS, this option is always set to Enabled. It is grayed out and does not allow user interaction.
Enable or disable the legacy serial port A.
Page 29 of 39
Configuration Menu
Item Description Item Specific Help
Base I/O Address Read-only. This item is visible only when the Serial Port A is enabled. The fixed value of this base I/O address is 3F8.
N/A
Interrupt Read-only. This item is visible only when the Serial Port A is enabled. The fixed value of this base I/O address is IRQ 4.
N/A
Serial Port B This item is used to configure the Super I/O-based serial port B. In the Standard BIOS and Full BIOS, available options are: - Disabled - Enabled (default) In the SCM BIOS, this option is always set to Enabled. It is grayed out and does not allow user interaction.
Enable or disable the legacy serial port B.
Base I/O Address Read-only. This item is visible only when the Serial Port A is enabled. The fixed value of this base I/O address is 2F8.
N/A
Interrupt Read-only. This item is visible only when the Serial Port A is enabled. The fixed value of this base I/O address is IRQ 3.
N/A
Parallel Port This item is visible only in the Full BIOS. Available options are: - Disabled - Enabled (default)
Enable or disable the legacy parallel port on the carrier board.
Page 30 of 39
Configuration Menu
Item Description Item Specific Help
Mode This item is visible only when Parallel Port set to Enabled. Available options are: - Output Only - Bi-directional - EPP: The Enhanced Parallel Port mode is compatible with IEEE 1284 specification. It is a half-duplex bi-directional interface designed to allow devices like printers, scanners, or storage devices to transmit large amounts of data. - ECP (default): The Extended Capabilities Port mode is compatible with IEEE1284. It is a half-duplex bi-directional interface similar to EPP, except that the system uses DMA to provide even faster data transfer than EPP.
Select the operation mode of this legacy parallel port.
Floppy Disk Controller This item is visible in the Full BIOS. Available options are: - Disabled - Enabled (default)
Enable or disable the legacy FDC port on the carrier board.
Page 31 of 39
Configuration Menu
Item Description Item Specific Help
Console Redirection This item is used to configure the console redirection with the available Super I/O-based serial ports. When this item is disabled, all settings beneath this item become invisible. In the Standard BIOS and Full BIOS, available options are: - Disabled - Serial Port A (default) - Serial Port B In the SCM BIOS, this option is always set to Serial Port A. It is grayed out and does not allow user interaction.
Select one legacy serial port for console redirection.
Baud Rate Available options are: - 300 - 1200 - 2400 - 9600 - 19.2K - 38.4K - 57.6K - 115.2K (default)
Check the baud rate supported by your device, and select the same or compliant baud rate here.
Console Type Available options are: - VT100 - VT100 8Bit - PC ANSI 7Bit - PC ANSI - VT100+ (default) - VT-UTF8 - ASCII
Check the console protocol supported by your device, and select the same console protocol Here.
Page 32 of 39
Boot Menu
Item Description Item Specific Help
Flow Control Available options are: - None (default) - CTS/RTS: This option is a standard method of hardware flow control between DTEs. CTS (Clear To Send) and RTS (Request To Send) are common RS-232 serial port control lines. - XON/XOFF: This option is a standard method of software flow control between modem and DTEs.
Select the type of transmit flow control used to control the data transmission between the network and data terminal equipments (DTE).
Console Connection Available options are: - Direct (default) - Via Modem
Specify whether the console is connected to the system directly or via a model.
Continue C.R. after POST Available options are: - Off - On (default)
Select On to enable console redirection after entering the operating system.
5. Boot Menu Figure 16. Boot menu
Phoenix BIOS Setup Utility
Main Information Configuration Boot Exit
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help 4Boot Order Summary Screen: [Disabled] Quick Boot Mode: [Enabled] POST Errors [Enabled]
Page 33 of 39
Boot Menu
BIOS Item Function Design Item Specific Help
Boot Order A submenu that includes the settings for boot priority orders and available boot order options.
Select the order of boot devices.
Summary Screen Available options are: - Disabled - Enabled (default)
Select Enabled to display the system configuration prior to loading the OS. Disabling this setting speeds up the boot process.
Boot-Time Diagnostic Screen
This item is visible only in the Standard BIOS and Full BIOS. Available options are: - Disabled (default) - Enabled For the SCM BIOS, though it is invisible, the system will display the diagnostic screen by default.
Select Enabled to display the diagnostic screen and customized boot logo during POST. When disabled, pressing ESC during POST displays the diagnostic screen.
Quick Boot Mode Available options are: - Disabled - Enabled (default)
Select Enabled to skip in-depth tests during system boot.
POST Errors Available options are: - Disabled (default) - Enabled
Select Enabled to pause the boot process and display the BIOS setup utility if system boot errors occur. When disabled, the system continues attempting to boot.
Page 34 of 39
Boot Menu
5.1 Boot Order
Figure 17. Boot Order
Phoenix BIOS Setup Utility
Configuration
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select Menu Enter Select Entry F10 Save and Exit
Item Specific Help
Boot Order
Boot Priority Order: 1: USB CD-ROM: 2: IDE: 3: PCI SCSI: 4: PCI LAN: Available Boot Devices: : USB KEY: : USB HDD: : USB ZIP: : USB LS120: : Other USB: : PCI: : Legacy LAN:
BIOS Item Function Design Item Specific Help
Boot Priority Order This item displays a list of the devices that are used to boot the system. The listed devices are selected from the Available Boot Devices list. Function keys are used to adjust the boot priority order.
<↑>and <↓>: Select a device. <+> and <->: Move a device up or down. <f> and <r>: Make a device fixed or removable. <x>: Exclude or include a device to boot. <Shift+1>: Enable or disable a device. <1-4>: Load default boot sequence.
Page 35 of 39
Exit menu
BIOS Item Function Design Item Specific Help
Available Boot Devices
This item displays all devices available to boot the system is displayed. Function keys are used to exclude or include a device to the boot priority order.
<↑>and <↓>: Select a device. <+> and <->: Move a device up or down. <f> and <r>: Make a device fixed or removable. <x>: Exclude or include a device for booting the system. <Shift+1>: Enable or disable a device. <1-4>: Load default boot sequence.
6. Exit menu
6.1 Exit menu for Standard BIOS and Full BIOS
Figure 18. Exit menu
Phoenix B IO S Setup U tility
M ain Inform ation Configuration Boot Exit
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select M enu Enter Select Entry F10 Save and Exit
Item Specific Help Exit Saving Changes Exit D iscarding Changes Load Defaults D iscard Changes Save Changes
CM O S Restore Condition: [Never] Save CM O S to F lash Erase CM O S from F lash Restore CM O S from F lash
BIOS Item Function Design Item Specific Help
Exit Saving Changes
Executable command. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Exit the BIOS setup utility and save changes to CMOS.
Page 36 of 39
Exit menu
BIOS Item Function Design Item Specific Help
Exit Discarding Changes
Executable command. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Exit the BIOS setup utility without saving changes to CMOS.
Load Setup Defaults
Executable command. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Before loading standard defaults, it is recommended that you first save your current configuration settings and then save CMOS into flash memory for future restoration. The Save CMOS to Flash command can perform this operation.
Discard Changes Executable command. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Discard all current changes before continuing.
Save Changes Executable command. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Save all current changes to CMOS.
CMOS Restore Condition
This item is invisible in the SCM BIOS. Changes to this item must be saved with the CMOS settings to flash memory before taking effect. Available options are: - Always: This option is usually useful when there is no CMOS battery on the carrier board. - Never (default) - CMOS Corruption
Specify the condition under which BIOS settings saved in the BIOS ROM flash memory will be automatically restored to CMOS in the BIOS RAM. Warning: If you select Always or CMOS Corruption, be sure to save CMOS settings to flash memory.
Save CMOS to Flash
Executable command. Performing this command will prompt a successful message window. This window provides a “Press any key to continue” button.
Take a moment to save current CMOS settings to nonvolatile flash memory. It takes effect after system reboot and allows you to restore the BIOS configuration settings saved in the flash memory.
Page 37 of 39
Exit menu
BIOS Item Function Design Item Specific Help
Erase CMOS from Flash
Executable command. Performing this command will prompt a successful message window. This window provides a “Press any key to continue” button.
Erase all previously-stored CMOS data from flash memory. It may take several seconds to complete the process.
Restore CMOS from Flash
Executable command. Performing this command will prompt a successful message window. This window provides a “Press any key to continue” button.
Restore CMOS settings from flash memory manually.
6.2 Exit menu for SCM BIOS
Figure 19. Exit menu
Phoenix B IO S Setup U tility
M ain Inform ation Configuration Boot Exit
F1 Help ↑↓ Select Item +/– Change Values F9 Setup Defaults ESC Exit ←→ Select M enu Enter Select Entry F10 Save and Exit
Item Specific Help Exit Saving Changes Exit D iscarding Changes Load Defaults D iscard Changes Save Changes
BIOS Item Function Design Item Specific Help
Exit Saving Changes
Executable command. The BIOS configuration will be saved into the BIOS RAM CMOS and BIOS ROM flash memory at the same time. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Exit the BIOS setup utility and save changes to BIOS RAM CMOS and BIOS ROM flash memory.
Page 38 of 39
BIOS Item Function Design Item Specific Help
Exit Discarding Changes
Executable command. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Exit the BIOS setup utility without saving changes.
Load Setup Defaults
Executable command. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Load default values for all BIOS configuration items.
Discard Changes Executable command. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Discard all current changes before continuing.
Save Changes Executable command. The BIOS configuration will be saved into the BIOS RAM CMOS and BIOS ROM flash memory at the same time. A confirmation message window prompts with two interactive buttons: - Yes (default) - No
Save all current changes to BIOS RAM CMOS and BIOS ROM flash memory.
Page 39 of 39
Recommended