View
2
Download
0
Category
Preview:
Citation preview
2PAGE
1
Shop online at www.bocedwards.com
Turbomolecular pumps
EXT turbomolecular pumpsEXT75DX turbomolecular pump 2-4EXT255DX turbomolecular pump 2-5EXT70 turbomolecular pump 2-6EXT70H compound molecular pump 2-7EXT255H compound molecular pump 2-8EXT556H compound molecular pump 2-9EXT performance graphs 2-10
Turbomolecular pump controllersEXC controllers 2-11TIC Turbo & instrument controller 2-13TIC Turbo controller 2-19
EXT accessories 2-25
EXPT combined outfits 2-27
STP magnetically levitated turbomolecular pumps and accessories
Data summary STP magnetically levitated turbomolecular pumps 2-30Optional accessories 2-33
Shop online at www.bocedwards.com
2PAGE
2
EXT TURBOMOLECULAR PUMPS AND EXC CONTROLLERS
EXT turbomolecular pumps
Our range of EXT turbomolecular and compound molecular pumps and EXC Controllers uses state-of-the-art technology to provide reliable, hydrocarbon-free, high and ultra high vacuum.
Key performance factorsA turbomolecular pump (TMP) is a multi-stage axial-flow turbine in which high speed rotating blades provide compression by increasing the probability of gas molecules moving in the pumping direction. The turbomolecular pump is optimized for molecular flow conditions and requires a suitably sized two stage rotary vane pump or an oil free scroll pump to exhaust to atmosphere.
A compound molecular pump (CMP) is based on the concept of combining bladed turbomolecular stages with molecular drag stages on the same rotor. This design allows:• High critical foreline pressures (typically up to 10 mbar)• Options to use smaller backing pumps or dry diaphragm backing pumps
Pumping speed (volume flow rate) is determined by the rotor diameter, inlet flange size and rotational speed. The pumping speed reduces at high inlet pressures to a value determined by the size of the backing pump.
As the inlet pressure rises, the motor power dissipation and pump temperature increase. Maximum continuous inlet pressure sets the maximum throughput limit for steady state pumping and depends on the cooling method used. Above this pressure, the rotational speed of the pump reduces as temperature sensors limit the pump power. With a water-cooled pump, the actual maximum throughput depends on the size of the backing pump.
Quiescent electrical power is the nominal power dissipated by a pump operating normally at full rotational speed and with low gas throughput (inlet pressure below the 10–3 mbar range). During the run-up time, or when operating at high gas throughput or above the critical backing pressure, the pump power dissipation will rise and approach the maximum power output for the EXC Controller used. Critical backing pressure for conventional turbomolecular pumps is approximately 0.1 to 0.2 mbar.
Compression ratio is determined by the rotational speed, the number of pump stages and the molecular weight of the pumped gas. It is higher for heavier gases which explains why the suppression of hydrocarbon backstreaming is so effective and why the ratio for hydrogen is important for ultra high vacuum applications.
Ultimate pressure measured according to Pneurop standards, is the lowest pressure achieved in the test system, 48 hours after bakeout. The system is backed only by a two-stage rotary vane pump. Fluoroelastomer inlet seals are used with ISO-flanged pumps and metal seals are used with CF-flanged pump models.
Bearing and suspension technologiesWe use two basic technologies: magnetic bearings and mechanical ceramic ball bearings.
Ceramic bearings, which are lubricated for life by either grease or oil, have replaced conventional steel bearings. The silicon nitride ceramic balls are lighter, harder and smoother than steel equivalents, leading to longer life and lower vibration characteristics. Reliability is increased because the ball and race materials are different, which prevents micro pitting.
Magnetic bearings further increase reliability. Our EXT turbomolecular pumps up to 540 l s-1 use a hybrid bearing arrangement with a permanent magnet upper bearing and an oil lubricated ceramic lower bearing.
Rotor technologiesWe use two basic technologies:• conventional full stack turbomolecular (typically 12 stages)• compound molecular (combining turbomolecular and drag stages)
In addition, EXT pumps up to 540 l s-1 use monobloc rotors machined from solid bar by computer controlled high speed milling machines. This technology produces stable, rigid rotors and allows virtually unlimited design flexibility for optimum vacuum performance.
Motor technologyEXT pumps use brushless d.c. motors and are available in 24 and 80 volt variants. For the 24 volt pumps the TIC line of controllers are available with the added benefit of integrated instrument controllers. For the 80 volt pumps you can choose from our EXC line of controllers to optimize the performance and cost options for your application.
The Controllers incorporate a regenerative back-up supply which provides power in the event of electrical supply failure to keep the vent-valve closed for several minutes.
Corrosive applicationsFor maximum life and reliability in the exacting process conditions encountered in semiconductor wafer processing applications, we recommend that you use turbomolecular pumps from our BOC Edwards STP-C and STPH-C series (see page 2-30). These Maglev pumps have magnetic bearings and are ideal for these harsh duty applications.
Purge portThe EXT pumps (with the exception of the EXT70 and EXT70H) all have purge-ports which can be used to purge the motor and bearing cavity with an inert gas (such as nitrogen). We recommend that you purge the pump when you pump corrosive and abrasive gas mixtures or those with an oxygen content over 20%. You can use our PRX10 purge-restrictor to set the purge gas flow rate. This typically adds up to 25 sccm to the total gas load and the backing pump must be sized accordingly.
Ceramic ball bearings
Shop online at www.bocedwards.com
2PAGE
3
TU
RB
OM
OL
EC
UL
AR
PU
MP
SVentingTo maintain the cleanliness of your vacuum system, we recommend that you vent a turbomolecular pump at or above half rotational speed, when the rotor is still spinning fast enough to suppress any backstreaming of hydrocarbons from the backing line.
The vent port on the EXT pump is part way up the rotor stack to ensure maximum cleanliness even with fluoroelastomer sealed vent-valves. Each pump is supplied with a manual vent-valve. If you use this manual valve care must be taken not to open it too quickly, especially if the system volume is small (typically less than the approximate volume of the turbomolecular pump), because if the rate of pressure rise is too high, the pump bearing life may be reduced.
In a small volume system, the rate of pressure rise will be greater than in a large volume for a given vent flow rate, and it may be necessary to restrict the vent gas flow. We offer the VRX range of vent restrictors which you can fit to your EXT pump, (see page 2-26).
Since the rate of pressure rise cannot be accurately controlled by the manual vent-valve, we recommend that, unless you fit a suitable VRX restrictor to the vent port, you must wait until the turbomolecular pump has slowed down to 50% speed, as indicated by the controller, before you open the manual vent-valve.
The maximum rate of pressure rise varies by pump model, and the Instruction Manual supplied with an EXT pump gives further guidance on this, and the size of vent restrictor needed to meet the fastest pressure rise allowed.
Control of the rate of venting is particularly important with pumps using fully magnetic bearings, otherwise the safety bearings may be damaged.
The manual vent-valve can be replaced with a TAV solenoid valve driven by the EXC Controller to allow venting after a 2 second delay on shut-off, or delaying vent until the rotational speed has dropped to 50%. The EXC Controller can also control the TAV vent-valve in the event of power or pump failure.
You can choose from two solenoid vent-valve options; the TAV5 which covers most auto-venting applications, and the TAV6 which has a higher conductance than the TAV5 and is designed either for use on larger chambers (typically with a volume greater than 10 liters), or when you want to use a two-stage venting procedure for the fastest possible vent times.
For two-stage venting you need two TAV valves. By using the appropriately restricted flow for the first stage vent-valve you can start venting when the EXT pump is still at full rotational speed. Once the pump has slowed to half rotational speed you can then introduce higher flow rates from the second stage vent-valve.
Inlet-screenAn inlet-screen is fitted as standard to all EXT pumps. The inlet-screen prevents debris from falling into the pump-inlet. In addition, the inlet-screen prevents you from coming into contact with the blades of the pump when it is disconnected from your vacuum system.
CoolingFor most applications, we recommend that you use forced-air cooling with the appropriate ACX air-cooler connected to your EXT pump. If the ambient temperature is below 30 °C, the EXT70 and EXT70H pumps can be cooled by free convection (dependent on gas load and backing pressure). NB: high gas load, high backing pressure and rapid cycling require more cooling.
However, if the ambient temperature is above 35 °C you must water-cool the EXT. The barbed connectors on the water-cooler are suitable for 6 mm internal diameter hose.
Water cooling reduces the running temperature of the pump motor and bearings and is particularly recommended when you operate the EXT with a continuous high throughput (that is, inlet pressure above 1 x 10-3 mbar) or when you bake the EXT pump to above 70 °C (measured at the inlet flange).
Scope of supplyFor end users desiring front panel controls and indications when using an 80 volt pump a minimum operating system requires you to order an EXT pump, an EXC controller and a pump to controller cable. For a 24 volt pump a minimum operating system requires you to order an EXT pump, a TIC controller and an EXDC controller. (The EXDC controller is not required when using an EXT75DX or EXT255DX).
Each EXT pump is supplied with an inlet-screen, elastomer inlet seal or copper gasket (as appropriate), manual vent valve and water-cooler. EXT75DX, EXT255DX and EXT555M require a water-cooler accessory in addition (if required).
Each EXC/TIC controller is supplied with a 2 m unterminated electrical supply cable.
Shop online at www.bocedwards.com
2PAGE
4
EXT75DX TURBOMOLECULAR PUMP
EXT75DX turbomolecular pumpEXT turbomolecular pumps
Features & benefits• Compatible with TIC Turbo and Instrument Controller• Multiple communication modes available
- Parallel mode allows traditional control signal interface- Serial mode allows RS-232 interface
• Numerous user configurable parameters via RS-232 interface- Vent valve control settings- Normal speed indication- Stand-by running speed- Programmable power settings- Power consumption- Pump temperature
• Enhanced monitoring capability including pump speed, power and temperature
TECHNICAL DATA
Inlet flange DN63ISO-K, DN63CF or DN40NW
Compression ratioN2 >1 × 1011
He 1 x 106
H2 5 x 104
Outlet flange DN16NWInterstage port (Hi variants) DN25NWRecommended backing pump1 E2M0.7Vent port !/8 inch BSPPurge port !/8 inch BSPMaximum continuous inlet pressure (light gas pumping) 2
water cooling (water at 15 °C, 2 × 10-2 mbarambient temp at 40 °C)forced air cooled, 35 °C ambient 1 × 10-2 mbar
Nominal rotational speed 90000 rpmStandby rotational speed Variable from 49500 to 90000
rpm(63000 rpm default)
Start time 90% speed3 110 sCooling method Forced air / waterAmbient air temperature for forcedair cooling 5-35 °CMinimum cooling water flow rate(water 15 °C) 15 l h-1
Water temperature range 10-20 °CMaximum inlet flange temperature 100 °COperating attitude Vertical and upright,
through to horizontalNoise level at 1 metre <50 dB(A)Maximum magnetic field 5 mTRecommended controller TIC100 turbo or turbo and
instrument controlledQuiescent electrical power 10 WInterstage pumping speed (Hi variants) 4 l s-1
INLET FLANGE ISO63 63CF DN40NW ISO100
Pumping speed (l s-1)3
N2 61 61 42 66He 57 57 49 59H2 53 53 48 54
Ultimate pressure (mbar)With rotary vane backing pump41 <5 × 10-9 <5 × 10-10 <5 × 10-9 <5 × 10-9
With diaphragm backing pump411 <5 × 10-8 <5 × 10-9 <5 × 10-8 <5 × 10-8
Weight (kg) 3.0 4.9 2.9 3.2
1 A larger backing pump may be required for maximum throughput. A suitable diaphragm pump with
ultimate <5 mbar may also be used.
2 Above this inlet pressure, rotational speed drops to below nominal.
3 Power limit set to 80 W.
41 Ultimate pressure 48 hours after bakeout with 2 stage rotary vane backing pump.
411 Ultimate pressure 48 hours after bakeout with Pb <5 mbar (500 Pa)
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Pump Inlet flangeEXT75DX ISO63 DN63ISO B72241000EXT75DX CF63 DN63CF B72242000EXT75DX NW40 DN40NW B72243000EXT75DX ISO100 DN100ISO B72245000EXT75iDX ISO63 DN63ISO (main)
DN16NW (interstage)B72237000
EXT75iDX ISO63 DN63ISO (main)DN25NW (interstage)
B72238000
EXT75iDX NW40 DN40NW (main)DN16NW (interstage)
B72235000
EXT75DX ISO100 DN25NW (backing) B72246000
ACCESSORIES ORDERING NUMBER
ACX75 air cooling accessory B58053075WCX500 water cooling accessory B73600121
A Manual vent valve in vent port E Purge Port (blanked off)
B Podule F Interstage port (EXT75iDX only)
C Logic interface connector G Podule connector socket
D Backing Port H Earth Connection
Shop online at www.bocedwards.com
2PAGE
5
TU
RB
OM
OL
EC
UL
AR
PU
MP
SEXT255DX TURBOMOLECULAR PUMP
EXT255DX turbomolecular pump
Features & benefits• Compatible with TIC Turbo and Instrument Controller• Multiple communication modes available
- Parallel mode allows traditional control signal interface- Serial mode allows RS-232 interface
• Numerous user configurable parameters via RS-232 interface- Vent valve control settings- Normal speed indication- Stand-by running speed- Programmable power settings- Power consumption- Pump temperature
• Enhanced monitoring capability including pump speed, power and temperature
TECHNICAL DATA
Inlet flange DN100ISO-K, DN100CFCompression ratio
N2 >1 × 108
He 4 x 105
H2 1.6 x 104
Outlet flange DN25NWInterstage port (Hi variants) DN25NWRecommended backing pump1 RV3Vent port !/8 inch BSP femalePurge port !/8 inch BSP femaleMaximum continuous inlet pressure (light gas pumping) 2
water cooling (water at 15 °C, 5 × 10-3 mbarambient temp at 40 °C)forced air cooled, 35 °C ambient 5 × 10-3 mbar
Nominal rotational speed 60000 rpmStandby rotational speed Variable from 33000 to 60000
rpm(42000 rpm default)
Start time 90% speed3 80 sCooling method Forced air / waterAmbient air temperature for forced air cooling 5-35 °CMinimum cooling water flow rate water 15 °C) 15 l h-1
Water temperature range 10-20 °CMaximum inlet flange temperature 100 °C (CF version)Operating attitude Vertical and upright,
through to horizontalNoise level at 1 metre <50 dB(A)Maximum magnetic field 5 mTRecommended controller TIC200 turbo or turbo and
instrument controlledQuiescent electrical power 25 WInterstage pumping speed (Hi variants) 10 l s-1
INLET FLANGE DN100ISO-K DN100CF
Pumping speed (l s-1)3
N2 220 220He 230 230H2 180 180
Ultimate pressure (mbar)With rotary vane backing pump41 <5 × 10-9 <5 × 10-10
With diaphragm backing pump411 <5 × 10-8 <5 × 10-9
Weight (kg) 6.25 8.6
1 A larger backing pump may be required for maximum throughput. A suitable diaphragm pump with
ultimate <5 mbar may also be used.
2 Above this inlet pressure, rotational speed drops to below nominal.
3 Power limit set to 160 W.
41 Ultimate pressure 48 hours after bakeout with 2 stage rotary vane backing pump.
411 Ultimate pressure 48 hours after bakeout with Pb <5 mbar (500 Pa)
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Pump Inlet flangeEXT2555DX ISO100 DN100ISO-K B75311000EXT255DX CF100 DN100CF B75312000EXT2555iDX ISO100 (interstage)
DN100ISO-K (main)DN25NW (interstage)
B75313000
ACCESSORIES ORDERING NUMBER
ACX250H air cooling accessory B58053160WCX500 water cooling accessory B73600121
A Manual vent valve in vent port E Podule connector socket
B Podule F Allowance for right-angle cable connector
C Logic interface connector G Earth bond point
D Backing Port
Shop online at www.bocedwards.com
2PAGE
6
EXT70 TURBOMOLECULAR PUMP
EXT70 turbomolecular pump
TECHNICAL DATA
Inlet flange DN40NW, DN50NW, DN63CF or DN63ISO-K
Compression ratioN2 >1 × 108
He 6000H2 500
Outlet flange DN16NWRecommended backing pump1 E2M0.7Vent-port !/8 inch BSP femaleMaximum continuous inlet pressure 2
water cooling at 15 °C, 40 °C ambient 3 × 10-2 mbarair cooling at 35 °C ambient 1 × 10-2 mbarfree convection at 30 °C ambient 6 × 10-3 mbar
Nominal rotational speed 90000 rpmStandby rotational speed 63000 rpmRun-up time 90% speed 90 sCooling method Free convection or forced air, or
waterMaximum inlet flange temperature 100 °CAmbient air temperature operating range
with free convection cooling 0-30 °Cwith forced air cooling 0-35 °C
Water temperature range(for water cooling) 10-20 °CMinimum water flow rate (at 15 °C) 15 l h-1
Operating attitude Vertical and upright,through to horizontal
Noise level at 1 metre <50 dB(A)Maximum magnetic field 5 mTRecommended Controller EXC100 or EXC120 Quiescent electrical power 10 W
EXT70 with DN63ISO-K, DN63CF, NW40 and NW50 inlet flanges
INLET FLANGE DN40NW DN50NW DN63CF DN63ISO-K
Pumping speed (l s-1)3
N2 52 60 65 65He 53 56 60 60H2 46 48 50 50
Ultimate pressure (mbar)4 <5 × 10-9 <5 × 10-9 <5 × 10-10 <5 × 10-9
Weight (kg) 1.4 1.4 3.4 1.5
1 A larger backing pump may be required for maximum throughput.
2 Above this inlet pressure, rotational speed drops to below nominal.
3 Pumping speeds are without an inlet screen. Inlet screens are supplied fitted and reduce speed by
about 10%.
4 Ultimate pressure 48 hours after bakeout with 2 stage rotary pump.
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Pump Inlet flangeEXT70 DN40NW B72203000EXT70 DN50NW B72204000EXT70 DN63CF B72202000EXT70 DN63ISO-K B72201000
157.
05
157.
05
F=
112
0.8
C
63
Ø50
106
4 x M4 x 6
Ø94
NW16A
45
E
A
32.6
DN63ISO-K
108
Ø113
DN63CF
Ø95
74D
109.
55
8 x Ø8.4
Ø92.1
164.
05
Ø55
NW40
Ø75
NW50
G
A Backing port (outlet flange) E Cooling-water connector
C Electrical supply connector F Allowance for right-angle cable connector
D Vent-valve G Earth bond point
Shop online at www.bocedwards.com
2PAGE
7
TU
RB
OM
OL
EC
UL
AR
PU
MP
SEXT70H COMPOUND MOLECULAR PUMP
EXT70H compound molecular pump
TECHNICAL DATA
Inlet flange DN40NW, DN63CF or DN63ISO-K
Outlet flange DN16NWRecommended backing pump1 E2M0.7Vent-port !/8 inch BSP femaleCompression ratio
N2 >1 × 108
He 4 × 105
H2 3 × 104
Maximum continuous inlet pressure2
water cooling at 15 °C 9 × 10-1 mbarair cooling at 35 °C 9 × 10-2 mbarfree convection at 30 °C 9 × 10-3 mbar
Nominal rotational speed 90000 rpmStandby rotational speed 63000 rpmRun-up time 90% speed 90 sCooling method Free convection or forced air,
or waterMaximum inlet flange temperature 100 °CAmbient air temperature operating range
with free convection cooling 0-30 °Cwith forced air cooling 0-35 °C
Water temperature range(for water cooling) 10-20 °CMinimum water flow rate (at 15 °C) 15 l h-1
Operating attitude Vertical and upright, through to horizontal
Noise level at 1 metre <50 dB(A)Maximum magnetic field 5 mTRecommended Controller
(80 V) EXC100 or EXC120
(24 V d.c.) EXDC80 & TICQuiescent electrical power 10 WInterstage pumping speed (Hi variants)
N2 6 l s-1
INLET FLANGE DN40NW DN63CF DN63ISO-K
Pumping speed (l s-1)3
N2 52 65 65He 53 60 60H2 46 50 50
Ultimate pressure (mbar)Rotary vane pump4 <5 × 10-9 <5 × 10-10 <5 × 10-9
Diaphragm pump5 <5 × 10-8 <5 × 10-8 <5 × 10-8
Weight (kg) 2.8 4.7 2.8
EXT70H with DN63ISO-K inlet flange
1 A larger backing pump may be required for maximum throughput. A suitable diaphragm backing pump
with ultimate <5 mbar may also be used.
2 With backing pressure <0.1 mbar. Above this inlet pressure, rotational speed drops to below nominal.
3 Pumping speeds are without an inlet screen. Inlet screens are supplied fitted and reduce speed by
about 10%.
4 Ultimate pressure 48 hours after bakeout with 2 stage rotary pump.
5 Using diaphragm pump with ultimate <5 mbar.
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Pump Inlet flangeEXT70H DN40NW B72223000EXT70H DN63CF B72222000EXT70H DN63ISO-K B72221000EXT70Hi DN63CF B72228000EXT70Hi DN63ISO-K B72229000TIC compatible packages* (24 V d.c.)EXT70H DN63-ISOK B72221991EXT70H DN63CF B72222991EXT70H DN40NW B72223991* EXDC-80 control module (P/N D39645000) also required See the entry for the TIC Turbo/Instrument controller at the end of this section for more information.
Ø92.1
F=
112
1.5
C
45
63
Ø50
106
4 x M4 x 6
Ø94
NW16A
E 33.5
DN63ISO-K
176
127
74
Ø113Ø95
76
A
G
D
128.
5
DN63CF
8 x Ø8.4
33.5
E
D
A
176
Ø55
NW40
135.
5
G
81
183
A Backing port (outlet flange)
C Electrical supply connector
D Vent-valve
E Cooling-water connector
F Allowance for right-angle cable connector
G Earth bond point
Shop online at www.bocedwards.com
2PAGE
8
EXT255H COMPOUND MOLECULAR PUMP
EXT255H compound molecular pump
TECHNICAL DATA
Inlet flange DN100ISO-K or DN100CFOutlet flange DN25NWVent-port !/8 inch BSP femalePurge-port !/8 inch BSP femalePumping speed1
N2 220 l s-1
He 230 l s-1
H2 180 l s-1
Compression ratioN2 >1 × 108
He 4 × 105
H2 1.6 × 104
Recommended backing pump2 RV3Maximum continuous inlet pressure3
water cooling at 15 °C, 40 °C ambient 5 × 10-3 mbarair cooling at 35 °C ambient 5 × 10-3 mbarfree convection at 40 °C ambient 4 × 10-4 mbar
Nominal rotational speed 60000 rpmStandby rotational speed 42000 rpmRun-up time to 90% speed
EXC100E 190 sEXC120 130 sEXC300 100 s
Cooling method Forced air or waterMaximum inlet flange temperature 100 °CAmbient air temperature operating range with forced air cooling 0-35 °CWater temperature range(for water cooling) 10-20 °CMinimum water flow rate (at 15 °C) 15 l h-1
Operating attitude Vertical and upright,through to horizontal
Noise level at 1 metre <50 dB(A)Maximum magnetic field 5 mTRecommended Controller
(80 V) EXC100, EXC120 or EXC300
(24 V d.c.) EXDC80 and EXDC160Other compatible Controller EXC300Quiescent electrical power 25 WInterstage pumping speed (Hi variant)
N2 10 l s-1
H2 10 l s-1
EXT255H with DN100ISO-K inlet flanges
INLET FLANGE DN100ISO-K DN100CF
Ultimate pressure (mbar)Rotary vane pump4 <5 × 10-9 <5 × 10-10
Diaphragm pump5 <5 × 10-8 <5 × 10-9
Weight (kg) 5.6 8.2
1 Pumping speeds are without an inlet screen. Inlet screens are supplied fitted and reduce speed by
about 10%.
2 A larger backing pump may be required for maximum throughput. A suitable diaphragm backing pump
with ultimate <5 mbar may also be used.
3 With backing pressure <0.1 mbar. Above this inlet pressure, rotational speed drops to below nominal.
4 Ultimate pressure 48 hours after bakeout with 2 stage rotary pump.
5 Using a diaphragm pump with ultimate <5 mbar.
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Pump Inlet flangeEXT255H DN100ISO-K B75301000EXT255H DN100CF B75302000EXT255Hi DN100ISO-K B75303000TIC compatible packages* (24 V d.c.)EXT255H DN100ISO-K B75301991EXT255H DN100CF B75302991EXT255Hi DN100ISO-K B75303991* EXDC 160 (P/N D39646000) or EXDC 80 (P/N D39645000) control module also required. See the TIC Turbo/Instrument controller entry at the end of this section for more information.
91
DN100ISO-K
190.
8
NW25
141F
1.5
A
45
C
A
131
190.
8
4 x M5 x 20
E
58.5
17
Ø152
NW10B
28
68
B
D
Ø130.2
Ø152Ø130
94
16 x Ø8.4
DN100CF
17
Ø86
G
A Backing port (outlet flange) E Cooling-water connector
B Purge-port (adaptor shown fitted) F Allowance for right-angle cable connector
C Electrical supply connector G Earth bond point
D Vent-valve
Shop online at www.bocedwards.com
2PAGE
9
TU
RB
OM
OL
EC
UL
AR
PU
MP
SEXT556H COMPOUND MOLECULAR PUMP
EXT556H compound molecular pumpEXT556H with DN160ISO-K and DN160CF inlet flange
TECHNICAL DATA
Main inlet flange DN160ISO-K / DN160CF
Outlet flange DN25NWVent port !/8 inch BSPPurge port !/8 inch BSPInlet pumping speed*
N2 540 l s-1
He 580 l s-1
H2 500 l s-1
Ar 510 l s-1
Compression ratio N2 >1010
He 108
H2 106
Ar >1010
Ultimate pressure (CF variant) <10-10 mbarRecommended backing pump RV12Maximum continuous inlet pressure (N2, He, H2)**
forced air cooled, 30 °C ambient 1x10-3 mbarforced air cooled, 35 °C ambient 5x10-4 mbarwater cooling at 15 °C 2x10-3 mbar
Nominal rotational speed 50000 rpmStart time to 90% speed
EXC250 5 minEXC300 6.5 minEXDC160 8 min
Cooling method forced air / waterAmbient air temperature for forced air cooling 0 °C – 35 °CRecommended cooling water flow rate (water at 15 °C) 15 l h-1
Water temperature 10 – 20 °C Maximum inlet flange temperature 80 °COperating attitude Vertical and upright,
through to horizontalNoise level at 1 metre <60 dBAMaximum magnetic field (standard envelopes)
Axial < 7 mTRadial < 3 mT
Maximum magnetic field (martensitic envelopes)Axial < 50 mTRadial < 50 mT
Recommended controllers EXC250, EXC300Quiescent power consumption 35 W
* Measured without inlet screen. Inlet screens are supplied fitted and may reduce speed by up to 20%
** With backing pressure < 0.3 mbar. Above this inlet pressure rotational speed drops.
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Pump Inlet flangeEXT556H ISO160 DN160ISO-K B77751000EXT556H CF160 DN160CF-K B77752000EXT556H ISO160(fine inlet screen)
DN160ISO-K B77761000
Martensitic envelopeEXT556H ISO160 DN160ISO-K B77757000EXT556H CF160 DN160ISO-K B77758000
ACCESSORIES ORDERING NUMBER
For safe and reliable operation, the EXT555H requires one of the following external cooling accessoriesACX555 Air cooling accessory B58053561WCX555 Water cooling accessory B58067003
A Inlet ISO100 E Purge port
B Inlet ISO160 F Backing port
C Vent port G Electrical connector
D Earth stud H Base mount holes (8)/Rubber feet (4)
A
H
E
B
D
F G
C
°45 °45
120.
521
9.1
246.
120
611
.75
240.
1
Ø210
NEW
Shop online at www.bocedwards.com
2PAGE
10
EXT PERFORMANCE GRAPHSEXT performance graphs
Pumping speed (pumping speed vs inlet pressure) Throughput (throughput vs inlet pressure)ls
-1
EXT70/70H/75DX
-610
200
100
0
400
300
-4-510 10
600
500
10-3
10
EXT250M/255H/255DX
-210
0-110
HeEXT556H
10-4
10-3
10 10-2 -1
10100 1
102
mbar
Pa
EXT250M/255H/255DX
-1ls
400
-60
100
10
200
300
EXT70/70H/75DX
-510 10
-4
500
600
1010-3
10-2 -1
100
2HEXT556H
10-3-4
10-2
10 10-1 0
101
102
10
mbar
Pa
EXT250M/255H/255DX
-1ls
EXT70/70H/75DX
0-6
10
100
200
300
400
-510 10
-4
500
600
1010-3
10-2 -1
100
2NEXT556H
10-4
10-3
10-2
1010-1 0
101
102
mbar
Pa
Nitrogen
Helium
Hydrogen
Helium
1010
10
10
10
-1m
bar
ls
10-4 -3
10
10
10
EXT556H
EXT70/70H/75DX
1010-2 -1 0
EXT250M/255H/255DX
-3
-2
-1
0
1
2
He
1010-2
10-1 0
101
102
mbar
Pa
1010-4
mba
r ls
-1
10-3
EXT556H
EXT70/70H/75DX
-210
-1 010
EXT250M/255H/255DX
10
10
10
10
10
10
-3
-2
-1
0
1
2
2N
10-2
10-1
100
101
102
mbar
Pa
Nitrogen
10
101010
0
EXT70
10-3 -2
10
110
102
10
3
CR
4
H2
2H
EXT70H
10-1 0
101
He
7
6
5
10
10
108
109
He
N2
N2
10 10-1 0
10101 2
103
mbar
Pa
CR
10
0
EXT556H
1010
0
-310
-1-210 10
10
101
102
10
3
4
110
7
610
5
10
108
109
H2
He
N2 Compression >10*12
10-1 0
101
10 102
103
mbar
Pa
10He
EXT250M
10-3
10
0
10
10
101
2
10
CR
3H
4
-210
-110
EXT255H/EXT255DX
010
110
2 2H
710
106
5
10
108
9
N2
N2
He
10-1 0
10 101
102
103
mbar
Pa
EXT75DX
N Compression >10212*
10
101010
0
10-3 -2
10
110
102
10
3
CR
4
10-1 0
101
7
6
5
10
10
108
109
10 10-1 0
10101 2
103
mbar
Pa
H2
He
Compression ratio (compression ration CR vs backing pressure)
Shop online at www.bocedwards.com
2PAGE
11
TU
RB
OM
OL
EC
UL
AR
PU
MP
SEXC CONTROLLERS
Turbomolecular pump controllersEXC controllersTurbomolecular pump controllersEXC100E, EXC100L, EXC120, EXC300M and EXC300 controllers
EXC controller rangeOur electronic drive EXC Controllers provide power and control for EXT pumps and accessories. There are seven Controllers: EXC100E, EXC100L, EXC250E, EXC250L, EXC120, EXC300 and EXC300M. All of these controllers, except the EXC300M, are compatible with our 80 V d.c. EXT turbomolecular pumps with brushless d.c. motors. The EXC300M is compatible with our magnetic bearing pump.
The EXC120 with a maximum power output of 120 W covers most pumping applications. The EXC300 is a high power version of the EXC120 and will run EXT pumps up to full speed faster than the EXC120 and will maintain pump performance at higher inlet pressures.
The EXC100 and EXC250 range of controllers have no front panel controls, and are intended for remote control only. The EXC100E and EXC250E have an external connector for use with the 1M, 3M and 5M pump-to-controller cables listed in the EXT accessories. The EXC100L and EXC250L are equipped with an integral 1M pump-to-controller cable.
Front panel controls and indicatorsWith the exception of the EXC100 and EXC250 range, all controllers have the following front panel controls and indicators:• Start/Stop – to switch the pump on and off• Standby – to switch the pump into standby mode, at 70% of full speed• Heater – to switch the bakeout band on and off• Fail indicator LED – is lit when the turbomolecular pump has tripped due
to over-temperature or overload.• Electrical supply indicator LED – is lit when the EXC is switched on.• Speed indicator bar graph – has a four segment display to show when
the turbomolecular pump is operating and has reached 25%, 50% and 75% of nominal speed.
Rear panel connectionsAll of the EXC Controllers have rear panel connectors for logic interface (for remote control), air-cooler, vent-valve and Active vacuum gauge. In addition, the EXC120, EXC300 and EXC300M have connectors for bakeout band electrical supply and rotary pump electrical supply switching.
The logic interface facilities are:• Remote control of Start, Stop and Standby.• Vacuum system interlocks to prevent incorrect operation of the
turbomolecular pump.• Normal and fault condition outputs• 0-5 V d.c. analog output proportional to turbomolecular pump speed
(0-10 V d.c. for EXC100 and EXC250 range)
The air-cooler and vent-valve electrical supplies are 24 V d.c. outputs which are suitable for use with BOC Edwards EXT accessories. The Active gauge connector is suitable for use with the BOC Edwards Active vacuum gauge heads, allowing the operation of the gauge head and the turbomolecular pump to be interlocked.
Features & benefits• Controllers can drive different pumps (except the EXC300M).• Switched-mode power supplies which automatically adjust to any
electrical supply.• Electromagnetic compatibility which exceeds the requirements of the
European generic immunity and emission standards.• Regenerative power supply which provides vent-valve control options.• Rear panel sockets for vent-valve, air-cooler and Active vacuum gauge.• Full remote control.• Standby and bakeout band control from front panel (except EXC100E,
EXC100L, EXC250E and EXC250L).• User selectable "normal" speed and time-out settings.• 0-5 V d.c. analog output proportional to turbomolecular pump
rotational speed. (0-10 V d.c. for EXC100E and EXC100L).
FEATURE EXC100E/L EXC250E/L EXC120 EXC300
Control functions available:Manual control ● ●
Remote control ● ● ● ●
Standby ● ● ● ●
Bakeout band front panel switch ● ●
Rotary pump switching relay ● ●
Hours counter ●
Display functions available:Electrical supply ● ●
Speed (4 segment bar graph) ● ●
Pump on ● ●
Pump awaiting interlock ● ●
Pump fail ●
Pump axial emergencyStandby on ● ●
Bakeout band on (pumpnormal)
● ●
Compatible turbomolecular pumps:EXT70, EXT70H ● ●
EXT255H ● ● ● ●
EXT555H series ● ●
Direct connection possible for:ACX air cooler ● ● ● ●
TAV vent-valve ● ● ● ●
BX bakeout band ● ●
Rotary pump switching ● ●
Active gauge ● ● ● ●
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
EXC100E D39620000EXC100L D39622000EXC250E D39635000EXC250L D39636000EXC120 D39616000EXC300 D39614000Electrical supply cables2 m no plug D400130202 m UK plug D400130252 m USA plug D400131202 m Northern European plug D40013030
Shop online at www.bocedwards.com
2PAGE
12
TECHNICAL DATA
EXC100E/L EXC250E/L EXC120 EXC300Electrical supply voltage (V) 90-264 90-264 90-264 90-132
and 180-264Electrical supply frequency (Hz) 47-63 47-63 47-63 47-63Maximum input power (VA)
Including bakeout band – – 410 700With no bakeout band 260 440 260 550
Maximum power output (W) 1003 250 110 290Ambient temperature range (°C) 0-40 0-40 0-40 0-40Enclosure protection rating IP20 IP20 IP20 IP20Electromagnetic emissions EN61326 class B EN61326 class B EN61326 class B EN61326 class BElectromagnetic immunity EN61326 EN61326 EN61326 EN61326Rotary pump contact rating1
Maximum current (A) – – 15 15Maximum voltage (V a.c.) – – 250 250
Weight (kg) 0.9 2.0 2.0 4.6Set-points
Timeout range on <50% speed (min) 1-30 1-30 1-30 1-30Factory set timeout (speed rising) (min) 8 8 8 8Timeout on speed falling (Y/N option) factory setting no no no noNormal speed set-point range (%)2 65-95 65-95 65-95 65-95Factory set normal speed (%)3 80 80 80 80
Vent options, factory settingsVent on Controller Stop, at 50% speed 50% speed 50% speed 50% speedVent on electrical supply fail, at 50% speed 50% speed 50% speed 50% speedVent on pump fail, at 50% speed 50% speed 50% speed 50% speedVent on axial emergency – – – –
Vent options, alternative selectable optionsVent on Controller Stop, after 2 s 2 s 2 s 2 sVent on pump fail, after 2 s 2 s 2 s 2 sVent on axial emergency – – – –
1 Inductive load with power factor of 0. 2 % of pump nominal rotational speed. 3 80 W pump + 20 W accessories
5215
115.5 F
EXC100E/L
F
A
6.85
M3
227.35
F
261.2
88.9C
75
13.4
15
G
E
1.6
122.
5
213
198.1
A
132.
5
Ø3.5
3 296
B
208.8
198.1
15
75
5.35
C
F
D
122.
5
112.
74.
9
Ø3.5
EXC300/EXC300M
EXC250E/L
7.6 246.65
261
M3
11575
1.6
15
100 88.9
13
15FF
F
F
F
C
E
G
A
A Front panel
B View from top
C Allowance for cable bend
D Panel cut-out
E View from side
F Clearance for ventilation
G Optional adaptor plate, to fit EXC100E in
place of EXC120E
142
127 Ø3.53 246
132.
5
122.
5
AB
137.7
75
5.35127
15
C
F
D 122.
5
112.
7
Ø3.5 4.9
EXC120
Shop online at www.bocedwards.com
2PAGE
13
TU
RB
OM
OL
EC
UL
AR
PU
MP
STIC TURBO & INSTRUMENT CONTROLLER
TIC Turbo & instrument controller
A compact turbo and instrument controller with a large clear graphical display, an intuitive user interface and serial communications providing full remote control and data logging functions via a new WindowsTM based PC program.
The controller automatically recognizes and supports up to three gauges from the BOC Edwards range (excluding IGC and Barocels), and one 24 V turbomolecular pump from the EXT range. Cooling and vent valve support is provided directly from the controller. Backing pump control is provided either for a compact 24 V diaphragm pump (on 200 W versions only), or where greater pumping speeds are required, mains backing pumps (up to E2M28) may be controlled via an optional relay box. The relay box also controls a mains heater band and backing line isolation valve and may include three 250 V a.c. 3 A changeover relays, which are activated by the gauge open collector set point outputs.
High pressure gauges may be used to initiate turbo pumps and low pressure gauges; alternatively, time delays and normal signals may be used to control events such as turbo and instrument start. There is a comprehensive selection of protection and safety interlock features.
The TIC turbo and instrument controller may be either rack or bench mounted and provides a useful hub for the flexible operation of a wide range of vacuum system configurations.
Features & benefitsUniversal turbo & instrument controller• TIC automatically recognizes and controls up to three active gauges and
one 24 V turbomolecular pump from either the DX or EXDC ranges. The 200 W version provides sufficient power to ensure optimum performance of larger 255 turbos. DX turbos have full serial communication with TIC and may be both configured and report status via TIC.
Backing pump support• Both mains and 24 V backing pumps may be controlled by TIC. The
200 W version supports the new XDD1 dry diaphragm pump. For larger vacuum systems both the 100 W and 200 W versions may control mains backing pumps, including XDS10 and up to RV12, via the optional relay box.
Relay options• Three optional relay boxes are available for use with TIC. These include
a version with three 250 V 3 A changeover relays, activated by the TIC internal open collector set point outputs. Another version controls a mains backing pump, turbo heater band and backing line isolation valve. The final relay box combines these features to provide 250 V changeover relays, backing pump and auxiliary controls.
• All relay boxes include a logic bypass facility for further system integration.
Simple system configuration• In most instances, TIC systems may be simply and quickly configured
using the range of standard cables on offer, there is therefore no need for the customer to prepare loom assemblies or relay boxes and special interfaces.
Direct pressure readout• TIC includes lookup tables for a range of commonly encountered
process gasses (N2, He, Ar, CO2, Kr & Ne). Selecting the appropriate gas enables direct readout of the correct pressure without the need to apply conversion factors.
Compact instrument• TIC is packaged in a compact case and may be panel or rack (¼ 19" rack
3U) mounted. With the addition of the bezel it becomes an attractive bench-top instrument.
Clear, easy to use graphical user interface• The large 128 x 64 pixel backlit graphics LCD and mobile phone style
menu system simplifies programing and with a choice of summary screens excellent visibility of displayed parameters is assured.
Universal power supply• TIC will operate from mains supplies with voltages between 90 and
264 V a.c., and frequencies between 47 and 63 Hz. No user intervention being required.
Serial communications• To enable complete integration into PC and PLC controlled processes,
all TIC variants include RS232 and RS485 interfaces as standard.
WindowsTM PC program• TIC is supplied with a new WindowsTM PC program which enables full
setup and control from a PC, using the RS232 interface.
Software upgrades• As new compatible products are released, TIC software may be simply
upgraded using the special utility supplied with the WindowsTM PC program.
TIC software upgrades will be made available via e-mail and the Internet.
TECHNICAL DATA
* Ramp speed is limited by the use of the EXDC80
** When configured to low power start
TURBO PUMP 24 V
TURBO PUMP OPTIONSTIC VARIANT
100 W 200 W
EXT75DX Fast FastEXT70H & EXDC80 Fast FastEXT255H & EXDC80* Slow SlowEXT255H & EXDC160 N/A FastEXT255DX Slow** Fast
Logic Interface The logic interface connector includes the functions listed below.It may be used either to link to system relays, a higher-level control system, or an optional relay box. By utilizing the relay box pass-through connector, a combination of a higher-level control system and relay box may be used.
Control inputsTurbo start/stop* Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.Turbo standby Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.Gauge enable 1, 2, 3 Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.Backing pump start/stop* Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.System interlock SYSI Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.
Shop online at www.bocedwards.com
2PAGE
14
Bench and rack mounting options (1/4 19" 3U sub rack)
External interfaces
Display – 128 x 64 pixel backlit graphics LCD
Front panel keypad control functions include:
Scroll up button
Scroll down button
Enter/Select button
Menu/Back button
Cycle button
Control outputsVent valve control O/C 24 V d.c. 100 mAHeater band control O/C 24 V d.c. 50 mABacking pump control O/C 24 V d.c. 100 mAAir cooler O/C 24 V d.c. 200 mA
Status outputsAnalog output 0-10 V d.c.
Set point A, B, C O/C 24 V d.c. 50 mATurbo normal speed O/C 24 V d.c. 50 mAAlarm O/C 24 V d.c. 50m ASerial interface The TIC has two built-in
communications protocols, RS232 and RS485.These may be used either to interface to a PLC or, using the WindowsTM PC software package supplied connected to a PC for full monitoring and control of a TIC system.
* Start/stop commands are "edge triggered".
TIC TURBO & INSTRUMENT CONTROLLER 100 W RS232
TIC TURBO & INSTRUMENT CONTROLLER200 W RS232
Mains inputElectrical supply 90 to 264 V a.c. 47 to 63 HzPower consumption (max)
215 VA 350 VA
Peak inrush current 10.3 A @ 110 V a.c.23.0 A @ 230 V a.c.
Fuse TIC is self-protecting and has no user replaceable fuse. The unit will recover when the overload is
removedEarth stud M4
Auxiliary terminalsAir cooling fan 24 V d.c. 3 W max, ACX70, ACX75
&ACX250H
Vent valve 24 V d.c. 2 W max, TAV5 & TAV6Interface cables Use cables as specified in "ordering
information"Dimensions
Electronics housing 110 mm high x 105 mm wide x 245 mm deep
Front panel 106 mm wide x 128 mm highWeight
Turbo & instrument controller 100 W RS232 2.75 kgTurbo & instrument controller 200 W RS232 3.5 kg
Operating temperature +0 ° to +40 °CStorage temperature -30 ° to +70 °CMaximum ambient operating humidity 90% RH non-condensing at 40 °CMaximum operating altitude 3000 mElectronic Design EN 61010-1Electromagnetic Compatibility EN 61326 Industrial Location,
Class B EmissionsEnclosure rating IP20
BOC EDWARDS
BOC EDWARDS
Shop online at www.bocedwards.com
2PAGE
15
TU
RB
OM
OL
EC
UL
AR
PU
MP
S
1 Gauge inputs FCC68 (RJ45)
2 Logic Interface 25-way 'D' socket
3 Backing pump 24 V 15-way 'D' socket *
4 Turbo pump 24 V 15-way 'D' socket
5 RS232/485 9-way 'D' socket
6 Earth stud M4
7 Mains input CEE/IEC 320 plug
8 Mains on/off switch
9 Auxiliary vent valve and fan terminals (24 V supply) 4 -way screw term
* Available on 200 W versions only
Display interface
TIC software is structured through a series of easily accessible screens, similar to a mobile telephone.
TIC automatically recognizes which gauges and turbo are connected and displays the appropriate information on the default summary screen. Scrolling and selecting accesses the control and set-up menus for that item.
Turbo speed is shown as a proportion of full speed by a bar graph. "Norm" indicates that the turbo has reached its Normal Speed, whilst forward or reverse facing chevrons indicate acceleration and deceleration.
Pump status is displayed, which combined with gauge outputs and relay status gives a clear indication of what is currently happening in the vacuum system.
There are a number of display options for maximum clarity. In addition, two levels of password protection may be applied, effectively restricting or preventing unauthorized intervention.
In the event of an error occurring, TIC will display either a WARNING or flash an ALARM. A warning advises of a condition outside normal parameters, requiring no action, but an alarm must be cleared before normal operation may resume.
Display units may be in mbar, Torr, Pa or Volts.
The three set point relays which are highlighted when tripped, may be linked to any gauge.
Gauge inputsInstrument supporting TIC variants recognize and control the following gauges:
APG, APGX, ATC, ASG, AIM, WRG & AIGX*
* No more than one AIGX gauge may be connected to TIC at a time.
Backing pump 24 V(For mains backing pump support, see below.)
200 W turbo supporting TIC variants recognize and control the following 24 V backing pumps:
XDD1
Relay box (optional)General description A range of relay boxes has been developed to allow TIC to operate three 250 V a.c. 3 A (non-inductive) changeover relays, mains backing pumps and accessories.
The changeover relays are activated by the TIC set point outputs. The mains backing pump relay controls a backing line isolation valve, such that when the backing pump is switched off the isolation valve closes.
The relay box is connected to the TIC via the logic interface connector, which is also provided with a bypass connector for interfacing with OEM equipment.
Relay box options
Compatible mains backing pumps and accessories
Small backing pumps: E2M0.7 & 1.5, RV3, 5, 8 & 12, XDS5C & 10C, XDS5 & 10 & ESDP12
Heater band: BX70 & BX250
Backing line isolation valve: LCPV16EKA & LCPV25EKA
1
2
5
8 67
3
4
9
Cha
ngeo
ver
rela
ys
(3 o
ff 25
0 V
a.c
. 3 A
)
Hea
ter
band
&
back
ing
line
isol
atio
n va
lve
Smal
l bac
king
pum
p
TIC Relay Box Instruments ✓
TIC Relay Box Small Backing pump ✓ ✓
TIC Relay Box Inst & Small Backing pump ✓ ✓ ✓
Shop online at www.bocedwards.com
2PAGE
16
1 Mains input CEE/IEC 320 plug ‡
2 Backing line isolation valve 3-way DIN socket ‡
3 250 V 3 A changeover relays 12-way Positronic plug *
4 Logic interface (from TIC) 25-way 'D' socket *‡
5 Logic bypass (to PC, PLC etc.) 25-way 'D' socket *‡
6 Earth stud M4 *‡
7 Heater band fuse ‡
8 Heater band CEE/IEC 320 socket ‡
9 Mains backing pump fuse ‡
10 Mains backing pump CEE/IEC 320 socket ‡
* Available on TIC Relay Box Instruments‡ Available on TIC Relay Box Small Backing
Note: Combined instrument and small backing pump variant shown.
WindowsTM PC programTIC is supplied with fully functional WindowsTM based PC software, which replicates and adds to the TIC control menus.
The PC software enables TIC systems to be configured, controlled and monitored from a single PC.
A useful data logging facility is also included, which saves user selectable parameters to file (in .csv format) for later analysis using suitable software..
TIC system configurations may be created and saved for use at a later date, thus saving programing time.
The PC software includes an upgrade utility, which enables the TIC software to be upgraded over the serial link from files supplied electronically.
8
9
7
10
1
6 5
2
4
3
Shop online at www.bocedwards.com
2PAGE
17
TU
RB
OM
OL
EC
UL
AR
PU
MP
SConfiguration examples
* When using an XDD1 pump, the turbo should be either controlled by a gauge or be subjected to a start
delay.
* For use with water cooled pumps only.
ITEM ORDERING NUMBER DESCRIPTION
A D39722000 TIC turbo/inst cont 200 W RS232*
B D40013025 2 m UK mains cable
C D14701000 WRG-S-NW25
D A74601991 XDD1 24 V d.c. diaphragm pump
E B72241000 EXT75DX ISO63
F B58053075 ACX75 air-cooler
G D39700836 XDD/DX/EXDC extension cable 2 m
H D39700836 XDD/DX/EXDC extension cable 2 m(optional)
J D40001005 0.5 m active gauge cable
ITEM ORDERING NUMBER DESCRIPTION
A D39721000 TIC turbo/inst cont 100 W RS232
B D40013025 2 m UK mains cable
C D39711805 TIC relay box small backing
D D02372000 APGX-M-NW25 STST
E D04850000 AIGX-S-NW25
F D14701000 WRG-S-NW25
G A65201903 RV3 pump 1-phase
H B72241000 EXT75DX ISO63
J B58052060 BX70 heater band 240 V 60 W*
K B58066010 TAV5 vent valve
L B58053075 ACX75 air-cooler
M D39700833 TIC logic interface cable 2 m
N D39700831 TIC mains cable IEC320 M/F 2 m
P D39700833 TIC logic interface cable 2 m
Q D39700836 XDD/DX/EXDC extension cable 2 m (optional)
R D39700834 TIC RS232 interface cable 2 m (optional
S D40001020 2 m active gauge cable
T N/A PC with RS232 interface (optional)
J
C
H
E
F
B
A
G
D
Q
S
T
F
E
S
D
R
H
L
K
J
B
A
C
B
N
P
G
M
Shop online at www.bocedwards.com
2PAGE
18
Configuration examples .
ITEM ORDERING NUMBER DESCRIPTION
A D39722000 TIC turbo/inst cont 200 W RS232
B D40013025 2 m UK mains cable
C D39711805 TIC relay box sml backing
D D02371000 APGX-M-NW16 AL
E D04850000 AIGX-S-NW25
F D14701000 WRG-S-NW25
G A72701903 XDS10
H D75301991 EXT255H DN100ISO-K 24 V
J D39646000 EXDC160 24 V
K B58066010 TAV5 vent valve
L B58053160 ACX250H air-cooler
M D39700831 TIC mains cable IEC320 M/F 2 m
N D39700833 TIC logic interface cable 2 m
P D39700836 XDD/DX/EXDC extension cable 2 m (optional)
Q D39700834 RS232 interface cable 2 m (optional)
R D40001010 1 m active gauge cable
S N/A PC with RS232 interface(optional)
QS
R
F
E
R
D
HJ
L
P
B
A
C
B
N
M
G
K
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Controllers (supplied with manuals and software)TIC turbo & instrument controller 100 W RS232 D39721000TIC turbo & instrument controller 200 W RS232 D39722000
Relay boxes (supplied with a set of mating connectors)
TIC relay box instruments (3 x 250 V a.c. 3 Achangeover relays)
D39700804
TIC relay box small backing pump D39711805TIC relay box instruments & small backing pump D39721806
CablesMains cables (TIC and relay box supply)
2 m UK plug D400130252 m USA plug D400131202 m Northern European plug D40013030
Mains cables (relay box to RV and XDS type pumps)2 m TIC mains cable IEC320 m/f D397008315 m TIC mains cable IEC320 m/f D39700832
Interface cables2 m TIC logic interface cable D397008332 m TIC RS232 interface cable D39700834
24 V pump extension cables (use with EXDC, DX & XDD1 type pumps)
1 m XDD/DX/EXDC extension cable D397008352 m XDD/DX/EXDC extension cable D397008365 m XDD/DX/EXDC extension cable D39700837
Active gauge cables (include FCC68 compatible connections at both ends)
0.5 m active gauge cable D400010051 m active gauge cable D400010103 m active gauge cable D400010305 m active gauge cable D4000105010 m active gauge cable D4000110015 m active gauge cable D4000115015 m active gauge cable (24 AWG) D4000515025 m active gauge cable D4000125030 m active gauge cable (24 AWG) D4000530050 m active gauge cable D40001500100 m active gauge cable D40001999
Other accessories and supporting productsTIC front bezel kit (spare) D39700803
Shop online at www.bocedwards.com
2PAGE
19
TU
RB
OM
OL
EC
UL
AR
PU
MP
STIC TURBO CONTROLLER
TIC Turbo controller
A compact turbo controller with a large clear graphical display, an intuitive user interface and serial communications providing full remote control and data logging functions via a new WindowsTM based PC program.
The controller automatically recognizes and supports one 24 V turbomolecular pump from the EXT range. Cooling and vent valve support is provided directly from the controller. Backing pump control is provided for a compact 24 V diaphragm pump (on 200 W versions only), or where greater pumping speeds are required, mains backing pumps (up to E2M28) may be controlled via an optional relay box. The relay box can also be used to control a mains heater band and backing line isolation valve.
Time delays and normal speed signals may be used to control events such as turbo start and there is a comprehensive selection of protection and safety interlock features.
The TIC turbo controller may be either rack or bench mounted and provides a useful hub for the flexible operation of a wide range of vacuum system configurations.
Features & benefitsUniversal turbo & instrument controller• TIC automatically recognizes and controls one 24 V turbomolecular
pump from either the DX or EXDC ranges. The 200 W version provides sufficient power to ensure optimum performance of larger 255 turbos. DX turbos have full serial communication with TIC and may be both configured and report status via TIC.
Backing pump support• Both mains and 24 V backing pumps may be controlled by TIC. The
200 W version supports the new XDD1 dry diaphragm pump. For larger vacuum systems both the 100 W and 200 W versions may control mains backing pumps, including XDS10 and up to RV12, via the optional relay box.
Relay options• The optional external relay box enables mains backing pumps to be
controlled and also provides interfaces for a turbo heater band, a backing line isolation valve and a logic bypass.
• All relay boxes include a logic bypass facility for further system integration.
Simple system configuration• In most instances, TIC systems may be simply and quickly configured
using the range of standard cables on offer, there is therefore no need for the customer to prepare loom assemblies or relay boxes and special interfaces.
Compact instrument• TIC is packaged in a compact case and may be panel or rack (¼ 19" rack
3U) mounted. With the addition of the bezel it becomes an attractive bench-top instrument.
Clear, easy to use graphical user interface• The large 128 x 64 pixel backlit graphics LCD and mobile phone style
menu system simplifies programing and with a choice of summary screens excellent visibility of displayed parameters is assured.
Universal power supply• TIC will operate from mains supplies with voltages between 90 and
264 V a.c., and frequencies between 47 and 63 Hz. No user intervention being required.
Serial communications• To enable complete integration into PC and PLC controlled processes,
all TIC variants include RS232 and RS485 interfaces as standard.
WindowsTM PC program• TIC is supplied with a new WindowsTM PC program which enables full
setup and control from a PC using the RS232 interface.
Software upgrades• As new compatible products are released, TIC software may be simply
upgraded using the special utility supplied with the WindowsTM PC program.
• TIC software upgrades will be made available via e-mail and the Internet.
TECHNICAL DATA
* Ramp speed is limited by the use of the EXDC80.
.
TURBO PUMP 24 V
TURBO PUMP OPTIONSTIC VARIANT
100 W 200 W
EXT75DX Fast FastEXT70H & EXDC80 Fast FastEXT255H & EXDC80* Slow SlowEXT255H & EXDC160 N/A Fast
Logic Interface The logic interface connector includes the functions listed below.It may be used either to link to system relays, a higher-level control system, or an optional relay box. By utilizing the relay box pass-through connector, a combination of a higher-level control system and relay box may be used.
Control inputsTurbo start/stop* Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.Turbo standby Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.Backing pump start/stop* Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.System interlock SYSI Closed when low: < 0.5 V d.c.
Open when High: 4 to 24 V d.c.Control outputs
Vent valve control O/C 24 V d.c. 100 mAHeater band control O/C 24 V d.c. 50 mABacking pump control O/C 24 V d.c. 100 mAAir cooler O/C 24 V d.c. 200 mA
Status outputsAnalog output 0-10 V d.c.Set point A, B, C O/C 24 V d.c. 50 mATurbo normal speed/alarm O/C 24 V d.c. 50m A
Serial interface The TIC has two built-in communications protocols, RS232 and RS485.These may be used either to interface to a PLC or, using the WindowsTM PC software package supplied connected to a PC for full monitoring and control of a TIC system.
* Start/stop commands are "edge triggered".
Shop online at www.bocedwards.com
2PAGE
20
Bench and rack mounting options (1/4 19" 3U sub rack)
External interfaces
Display – 128 x 64 pixel backlit graphics LCD
Front panel keypad control functions include:
Scroll up button
Scroll down button
Enter/Select button
Menu/Back button
Cycle button
TIC TURBO CONTROLLER100 W RS232
TIC TURBO CONTROLLER200 W RS232
Mains inputElectrical supply 90 to 264 V a.c. 47 to 63 HzPower consumption (max)
215 VA 350 VA
Peak inrush current 10.3 A @ 110 V a.c.23.0 A @ 230 V a.c.
Fuse TIC is self-protecting and has no user replaceable fuse. The unit will recover when the overload is
removedEarth stud M4
Auxiliary terminalsAir cooling fan 24 V d.c. 3 W max, ACX70, ACX75
&ACX250H
Vent Valve 24 V d.c. 2 W max, TAV5 & TAV6Interface cables Use cables as specified in "ordering
information"Dimensions
Electronics housing 110 mm high x 105 mm wide x 245 mm deep
Front panel 106 mm wide x 128 mm highWeight
TIC Turbo controller 100 W RS232
2.75 kg
TIC Turbo controller 200 W RS232
3.5 kg
Operating temperature +0 ° to +40 °CStorage temperature -30 ° to +70 °CMaximum ambient operating humidity 90% RH non-condensing at 40 °CMaximum operating altitude 3000 mElectronic design EN 61010-1Electromagnetic compatibility EN 61326 (Industrial Location,
Class B Emissions)Enclosure rating IP20
BOC EDWARDS
BOC EDWARDS
Shop online at www.bocedwards.com
2PAGE
21
TU
RB
OM
OL
EC
UL
AR
PU
MP
S
1 Backing pump 24 V 15-way 'D' socket *
2 Turbo pump 24 V 15-way 'D' socket
3 Logic Interface 25-way 'D' socket
4 RS232/485 9-way 'D' socket
5 Earth stud M4
6 Mains input CEE/IEC 320 plug
7 Mains on/off switch
8 Auxiliary vent valve and fan terminals (24 V supply) 4 -way screw term
* Available on 200 W versions only
Display interface
TIC software is structured through a series of easily accessible screens, similar to a mobile telephone.
TIC automatically recognizes which turbo connected and displays the appropriate information on the default summary screen. Scrolling and selecting accesses the control and set-up menus for that item.
Turbo speed is shown as a proportion of full speed by a bar graph. "Norm" indicates that the turbo has reached its Normal Speed, whilst forward or reverse facing chevrons indicate acceleration and deceleration.
Two levels of password protection are available, effectively restricting or preventing unauthorized intervention.
Pump status is displayed, giving a clear indication of what is currently happening in the vacuum system.
In the event of an error occurring, TIC will display either a WARNING or flash an ALARM. A warning advises of a condition outside normal parameters, requiring no action, but an alarm must be cleared before normal operation may resume
The three setpoint relays, which are highlighted when tripped, may be linked to turbo speed.
Backing pump 24 V(For mains backing pump support, see below.)
200 W turbo supporting TIC variants recognize and control the following 24 V backing pumps:
XDD1
Relay box (optional)General description A range of relay boxes has been developed to allow TIC to operate mains backing pumps and accessories.
The mains backing pump relay controls a backing line isolation valve, such that when the backing pump is switched off the isolation valve closes.
The relay box is connected to the TIC via the logic interface connector, which is also provided with a bypass connector for interfacing with OEM equipment.
Relay box options
Compatible mains backing pumps and accessories
Small backing pumps: E2M0.7 & 1.5, RV3, 5, 8 & 12, XDSC5 & 10, XDS5 & 10, ESDP12
Heater band: BX70 & BX250
Backing line isolation valve: LCPV16EKA & LCPV25EKA
1 Mains input CEE/IEC 320 plug
2 Backing line isolation valve 3-way DIN socket
3 Logic interface (from TIC) 25-way 'D' socket
4 Logic bypass (to PC, PLC etc.) 25-way 'D' socket
5 Earth stud M4
6 Heater band fuse
7 Heater band CEE/IEC 320 socket
8 Mains backing pump fuse
9 Mains backing pump CEE/IEC 320 socket
4
3
7 6 5
8
1 2
Cha
ngeo
ver
rela
ys(3
off
250
V a
.c. 3
A)
Hea
ter
band
&
back
ing
line
isol
atio
n va
lve
Smal
l bac
king
pum
p
TIC Relay Box Small Backing pump ✓ ✓
TIC Relay Box Inst & Small Backing pump ✓
ISOLATION
7
8
6
HEATER
BACKING PUMP
F2
F1
9
MAINS IN
1
30V
MA
X
TICUSER
5 4
LOG
IC IN
TE
RF
AC
E
VALVE
2
3
Shop online at www.bocedwards.com
2PAGE
22
WindowsTM PC programTIC is supplied with a fully functional WindowsTM based PC software, which replicates and adds to the TIC embedded control menus.
The PC software enables TIC systems to be configured, controlled and monitored from a single PC.
A useful data logging facility is also included, which saves user selectable parameters to file (in .csv format) for later analysis using suitable software.
TIC system configurations may be created and saved for use at a later date, thus saving programing time.
The PC software includes an upgrade utility, which enables the TIC embedded software to be upgraded over the serial link from files supplied electronically.
Shop online at www.bocedwards.com
2PAGE
23
TU
RB
OM
OL
EC
UL
AR
PU
MP
SConfiguration examples
* When using an XDD1 pump, the turbo should be subjected to a short delay.
* For use with water cooled pumps only.
ITEM ORDERING NUMBER DESCRIPTION
A D39712000 TIC turbo 200 W RS232*
B D40013025 2 m UK mains cable
C A74601991 XDD1 24 V d.c. diaphragm pump
D B72241000 EXT75DX ISO63
E B58053075 ACX75 air-cooler
F D39700836 XDD/DX/EXDC extension cable 2 m
G D39700836 XDD/DX/EXDC extension cable 2 m (optional)
ITEM ORDERING NUMBER DESCRIPTION
A D39712000 TIC turbo cont 200 W RS232
B D40013025 2 m UK mains cable
C D39711805 TIC relay box sml bkg
D A74601991 XDD1 24 V d.c. diaphragm pump
E B72241000 EXT75DX ISO63
F B58052060 BX70 heater band 240 V 60 W*
G B58066010 TAV5 vent valve
H B58053075 ACX75 air-cooler
J D39700833 TIC logic interface cable 2 m
K D39700836 XDD/DX/EXDC extension cable 2 m
L D39700836 XDD/DX/EXDC extension cable 2 m (optional)
M D39700834 TIC RS232 interface cable 2 m (optional)
N N/A PC with RS232 interface (optional)
G
D
E
A
B
F
C
L
N M
E
H
G
F
B
A
C
J
B
K
D
Shop online at www.bocedwards.com
2PAGE
24
Configuration examples .
ITEM ORDERING NUMBER DESCRIPTION
A D39711000 TIC turbo cont 100 W RS232
B D40013025 2 m UK mains cable
C D39711805 TIC relay box sml bkg
D A37122919 E2M1.5 pump 1-phase
E B72221991 EXT70H DN63ISO-K 24 V
F D39645000 EXDC80 24 V
G B58066010 TAV5 vent valve
H B58053075 ACX75 air-cooler
J D39700833 TIC logic interface cable 2 m
K D39700836 XDD/DX/EXDC extension cable 2 m (optional)
L D39700834 TIC RS232 interface cable 2 m (optional)
M N/A PC with RS232 Interface(optional)
J
M L
B
B
A
C
K
H
FE
D
G
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Controllers (supplied with manuals & software)TIC turbo controller 100 W RS232 D39711000TIC turbo controller 200 W RS232 D39712000
Relay boxes (supplied with a set of mating connectors)
TIC relay box small backing D39711805CablesMains cables (TIC and relay box supply)
2 m UK plug D400130252 m USA plug D400131202 m Northern European plug D40013030
Mains cables (relay box to RV and XDS type pumps)2 m TIC mains cable IEC320 m/f D397008315 m TIC mains cable IEC320 m/f D39700832
Interface cables2 m TIC logic interface cable D397008332 m TIC RS232 interface cable D39700834
24 V pump extension cables (use with EXDC, DX & XDD1 type pumps)
1 m XDD/DX/EXDC extension cable D397008352 m XDD/DX/EXDC extension cable D397008365 m XDD/DX/EXDC extension cable D39700837
Other accessories and supporting productsTIC front bezel kit (spare) D39700803
Shop online at www.bocedwards.com
2PAGE
25
TU
RB
OM
OL
EC
UL
AR
PU
MP
SEXT ACCESSORIES
EXT accessoriesEXT accessories
We offer a complete range of accessories and spares for the EXT pumps. A brief description of each of these items is given below.
1 Vibration isolator 8 Water-cooler (supplied with pump
2 BX Bakeout band 9 ACX air-cooler (design varies with pump)
3 Inlet-flange seal (supplied with pump) 10 NW10 vent-port adaptor
4 Inlet-screen (supplied with pump) 11 TAV vent-valve
5 EXT pump 12 Vent-port (pump supplied with manual
6 Purge port (NW10 adaptor fitted) vent-valve)
7 PRX10 purge-restrictor 13 Bakeout band position
PUMP-TO-CONTROLLER CABLE
A pump-to-controller cable must be ordered separately for EXC100E & EXC250E and is available in 1, 3 and 5 m lengths, to suit your installation, (other lengths are available on request).
ACX AIR-COOLER
An ACX air-cooler is used to cool an EXT pump when a suitable cooling-water supply is not available or for an EXT pump in a mobile pumping system. The ACX air-cooler is an enclosed electrical fan and fixing bracket assembly which is easily fitted to bolt holes in the base of the pump.
The ACX air-cooler has a 24 V d.c. motor which can be powered and controlled from a rear panel socket on the EXC/TIC Controller or DX pump. It is supplied with 3 m of electrical cable.
BX BAKEOUT BAND
Use a BX bakeout band to increase the rate of degassing of the pump body to achieve faster pump down and lower ultimate pressure. Bakeout bands are only fitted to CF flanged pumps and/or intended for use in ultra high vacuum systems.
Bakeout bands are available for use with 110-120 or 220-240 V a.c. electrical supplies and can be powered from a rear panel socket on the EXC/TIC Controller or DX pump. It is supplied with 3 m cable and mating CE22 connector.
PRX10 PURGE-RESTRICTOR
The PRX10 purge-restrictor is used to set the flow-rate of purge gas into the EXT pump. All of the EXT pumps (except the EXT70 and EXT70H) have a purge-port to allow you to purge the motor and bearing cavity with dry nitrogen or another inert gas. Fit a vent-port adaptor to the purge-port of the EXT255H or EXT255DX pumps to convert it from !/8 inch BSP to DN10NW, before you use the PRX10.
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
1 m cable D396180103 m cable D396180305 m cable D39618050
9
10
11
13
12
8
7
6
5
4
3
2
1
ORDERING INFORMATION
PRODUCT DESCRIPTION TO FIT PUMPS ORDERING NUMBER
ACX75 EXT70, EXT70H, EXT75DX B58053075ACX250H EXT255H, EXT255DX B58053160ACX555H EXT556H B58053561
ORDERING INFORMATION
PRODUCT DESCRIPTION TO FIT PUMPS ORDERING NUMBER
BX70, 110 V, 30 W EXT70, EXT70H, EXT75DX B58052040BX70, 240 V, 30 W EXT70, EXT70H, EXT75DX B58052060BX250, 110 V, 60 W EXT255H, EXT255DX B58052041BX250, 240 V, 60 W EXT255H, EXT255DX B58052061BX501, 110 V, 100 W EXT556H B58052044BX501, 240 V, 100 W EXT556H B58052064
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
PRX10 purge-restrictor B58065001
Shop online at www.bocedwards.com
2PAGE
26
TAV VENT-VALVE
The TAV vent-valves are 24 V d.c. solenoid operated valves which you can use to vent your vacuum system with atmospheric air or dry nitrogen when you switch off the EXT pump. The valves are supplied with a sintered bronze inlet-filter, a riffled hose connector, 3 m of electrical cable and a DN10NW adaptor. The vent-valves can be powered and controlled from a rear panel socket on the EXC Controller. You can either use your TAV vent-valve to replace the manual vent-valve supplied with the EXT pump, or adapt it to fit any other suitable port on the vacuum system upstream of the turbomolecular pump. For further advice about the choice of TAV vent-valve, see page 2-3.
VENT-PORT ADAPTOR
This !/8 inch BSP male to DN10NW adaptor can be used to replace the TAV5 vent-valve or the manual vent-valve fitted to the EXT pumps. It allows the threaded vent-port on the pump (and the threaded purge-port on the EXT255H and EXT556H) to be converted to a DN10NW flange.
The vent-port adaptor is supplied with a removable flow-restrictor and an "O" ring to seal the adaptor to the pump.
VIBRATION ISOLATOR
A vibration isolator can be fitted to the inlet-flange of the EXT pump to reduce the transmission of the small amount of vibration generated by the pump to your vacuum system. The vibration isolator has two flanges separated by a flexible stainless steel bellows and an outer rubber anti-vibration collar.
The vibration isolator is designed for use with vertically mounted pumps only.
VRX VENT-RESTRICTOR
Fit a VRX vent-restrictor to your EXT pump if you will vent the pump when the pump speed is above 50% of full rotational speed. The vent-restrictor restricts the flow-rate of the vent gas into the EXT pump. You can also use the VRX to replace the standard restrictor supplied with the PRX10 purge restrictor to obtain a different purge rate.
You can fit the vent-restrictor to the TAV vent-valve, to the vent-port adaptor or directly to the vent or purge port of the EXT255H and EXT255DX pumps.
EXT SPARES
Each EXT pump is supplied with an inlet seal, inlet screen and water cooler (with the exception of DX pumps). These items may also be ordered as spares.ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
TAV5 vent-valve B58066010TAV6 vent-valve B58066020
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
Vent-port adaptor B58066011
ORDERING INFORMATION
TO FIT PUMP INLET-FLANGE ORDERING NUMBER
DN63CF B58101000DN63ISO-K B58115000DN100ISO-K B58120000DN160ISO-K B58125000DN100CF B58105000DN160CF B58110000
44
46
ORDERING INFORMATION
VRX VENT-RESTRICTOR ORIFICE DIAMETER (MM) ORDERING NUMBER
VRX10 0.1 B58066021VRX20 0.2 B58066022VRX30 0.3 B58066023VRX50 0.5 B58066024VRX70 0.7 B58066025
ORDERING INFORMATION
PRODUCT DESCRIPTION PUMP TYPE
TO FIT INLET FLANGE SIZE ORDERING NUMBER
Inlet flange sealsDN40NW Co-Seal, fluoroelastomer B27158453DN50NW Co-Seal, fluoroelastomer B27158466ISO63 Trapped "O" ring, fluoroelastomer B27158170ISO100 Trapped "O" ring, fluoroelastomer B27158171ISO160 Co-Seal, fluoroelastomer B2715807463CF copper compression gasket (pack of 10) C10007490100CF copper compression gasket (pack of 10) C10009290160CF copper compression gasket (pack of 5) C10011290
ISX inlet-screen
ISX63/4 EXT70, EXT70H DN63ISO-K, DN63CF B58051005ISX100/6 EXT70, EXT70H,
EXT255H, EXT255DXDN100ISO-K, DN100CF
B58051001
ISDX63/4 EXT75DX DN63ISO-K, DN63CF B72240860ISHX160/8C EXT556H
(coarse)DN160ISO-K, DN160CF
B58051007
ISHX160/8F EXT556H(fine)
DN160ISO-K, DN160CF
B58051008
WCX water-cooler
WCX250M B73501164WCX500 EXT70, EXT70H,
EXT255H, EXT75DX, EXT255DX
B73600121
WCX555H EXT556H B58067003
Shop online at www.bocedwards.com
2PAGE
27
TU
RB
OM
OL
EC
UL
AR
PU
MP
SEXPT 1 AND 2 PUMPING STATIONS
EXPT combined outfitsEXPT combined outfits
Our new range of EXPT pumping outfits brings added flexibility with our successful TIC Turbo and Instrument Controllers. A large selection of backing and turbo pumps are available in combination with TICs and accessories to suit a wide variety of applications such as:• UHV systems• Beam lines• Load locks• Surface science• High energy physics
Features & benefits• Fully assembled and ready to use• System start/stop from control panel• Control of both the turbo pump and gauges* from the integrated TIC• Serial communication control available with RS232 and RS485• Dry pumping options with XDD1, XDS5 and XDS10
For North America and Brazil, see photos below. Contact our National Sales Centre at 1800-848-9800. Please note, these cart systems are available in North America & Brazil only. All other territories, see information above.
EXPT1 – Base plate with EXT70H turbo pump and XDD1 diaphragm pump with TIC.
EXPT2 – Base plate with EXT255H turbo pump and XDS10 scroll pump with TIC.
ORDERING INFORMATIONThis information applies to our UK-made turbo casts. For US-made turbo casts, please contact our national sales centre at 1-800-848-9800.
Turbomolecular pumpM EXT75DXN EXT255DXY EXT70HZ EXT255H
Flange type1 DN40NW2 DN63ISO-K3 DN63CF4 DN100ISO-K5 DN100CF
Backing pump1 E2M0.72 E2M1.53 RV34 RV55 RV86 RV12A XDD1B XDS5C XDS10
Mounting1 EXPT12 EXPT2
InstrumentationTurbo control only 100 W 1Turbo and instrument control 100 W 2Turbo control only 200 W 3Turbo and instrument control 200 W 4
Backing pump accessoriesNone 0EMF mist filter 1FL20K foreline trap 2Castors 31+2 41+3 52+3 61+2+3 7Castors + silencer 8
Turbomolecular pump accessoriesNone 0TAV5 vent valve 1LCPVEK backing isolation valve 31+3 5
Electrical supply220-240 V 50/60 Hz (Europe) 1110-120 V 50/60 Hz (USA) 2100 V 50/60 Hz (Japan) 3220-240 V 50/60 Hz (UK) 4
* Gauges and cables to be ordered separately.Not all combinations are permissible. Please consult your regional BOC Edwards centre.Units are supplied with integral air cooler.Please refer to working instructions or your regional BOC Edwards center for compatible gases.
T – –
Shop online at www.bocedwards.com
2PAGE
28
STP MAGNETICALLY LEVITATED TURBOMOLECULAR PUMPS
STP magnetically levitated turbomolecular pumps and accessories
In April 2002, BOC Edwards acquired the turbomolecular pump business of Seiko Instruments, Inc.• Distributed and supported globally by BOC Edwards for nearly twenty
years• Designed by continuous improvement on existing proven reliable
technology• Advanced materials and designs provide:
- Class leading performance- Low vibration- Guaranteed reliability- Low cost of ownership
• The broad product range covers all potential turbo pump applications.• Qualified by all major semiconductor OEM’s• Used in all major semiconductor fabrication plants• Installed base of over 70000 units, 85% in the semiconductor industry
Key features• Multi-axis magnetic bearing system• High Throughput versions for high flow processes• Low vibration characteristics• Advanced controller technology• Full interfacing capability
Features & benefits• Improved pumping performance
- Optimized for semiconductor process pressures- Maximized gas throughput for each flange size- Applications specific models
• New generation controllers• Compact (1/2 rack) controller
- Auto tune enabling "mix and match" pumps- Integrated TMS control- Improved diagnostics
• High power d.c. motor drive- Fast ramp-up time- Self regeneration upon power failure, eliminating the need for
batteries
BOC Edwards is a leader in clean and dry vacuum technology. The first STP pumps were sold in 1983 and there are now over 70000 installations worldwide. 85% are operating on semiconductor process tools where they demonstrate exceptional levels of reliability. STP pumps are the first choice for applications demanding high up-time, hydrocarbon-free pumping, minimal maintenance and low vibration.• Proven reliability.• Clean oil-free high vacuum.• Complete range from 300 to 3500 l s-1.• Application specific models.• Very low noise and vibration.• Low cost of ownership.• Virtually maintenance free.• Installation in any orientation.• Full remote control interface.• Supported globally by BOC Edwards
Proven magnetic bearing technologyThe rotor is entirely suspended by magnetic bearings so all contact between the rotor and the remainder of the pump is eliminated. As well as giving very low vibration, the elimination of contact means no bearing wear and no requirement for consequent pump maintenance.
STP rangeUHV series The Ultra High Vacuum series of magnetically levitated turbo molecular pumps are the products of choice for the semiconductor, surface science or high energy physics industries. They offer unrivalled reliability, performance, cleanliness and class leading low vibration levels. The pumps are all d.c. powered, eliminating the need for batteries, they use a half rack controller which features auto-tuning and advanced diagnostic features. The range contains pumps with speeds from 300 l s-1 to 1000 l s-1 all of which are available in ISO or CF flange variants.High throughput series The high throughput series of magnetically levitated turbo pumps generate the high gas flows required by the current generation of semiconductor etch, ion implant and LCD systems. All the pumps feature a five active axis magnetic bearing system and a d.c. drive for increased robustness and stability. They use a Holweck stage to provide advanced throughput performance. They operate via a half rack controller with auto-tuning, advanced diagnostics and an integrated temperature management system. The range operates with throughput speeds from 300 l s-1 to 450 l s-1.
Shop online at www.bocedwards.com
2PAGE
29
TU
RB
OM
OL
EC
UL
AR
PU
MP
SAdvantage series The new Advantage series of magnetically levitated turbo pumps have been designed to provide the highest levels of throughput required by the next generation of semiconductor etch and CVD processes. They have been developed, using continuous improvement techniques, from the ultra reliable, high performance H series of products. Their advanced rotor design combined with selection of the best materials has allowed the creation of the next generation of high throughput turbo pump inside the same footprint as many of the existing models. The range contains pumps with throughput speeds from 800 l s-1 to 3500 l s-1.
STP features
Oil free All STP turbomolecular pumps are oil free. The use of magnetic bearings eliminates all hydrocarbon lubricants ensuring no contamination of the vacuum process from the turbomolecular pump. This feature is vital in the semiconductor industry (where device densities are constantly increasing) and in surface science or high energy physics applications (where even minute degrees of contamination disrupt measurements).
Maintenance free Unlike conventional mechanical bearings, magnetic levitation means there is no frictional contact, eliminating sources of wear and vibration. This feature enables STP turbomolecular pumps to run for years with virtually no maintenance, reducing annual operating costs to a minimum and ensuring maximum up-time is achieved. This maintenance free feature can be particularly beneficial on processes producing chemical or radioactive contamination.
Vibration free Magnetic levitation of the rotor results in an extremely low level of noise and vibration. Peak-to-peak vibration level is less than 0.02 µm. This amplitude remains constant throughout the life of the pump and is free from troublesome sub-harmonics.
Automatic balancing system (ABS) ABS is a unique patented development of 5-axis technology. If any rotor imbalance is introduced (by deposition of process by-products, for example), sensors in the pump detect changes in the rotor motion and compensate the magnetic bearing fields to allow the rotor to spin on its natural inertial axis. This minimizes the vibration transmitted to the inlet flange. ABS works at all pump rotational speeds.
Safety backup bearings STP pumps have dry lubricated axial and radial mechanical bearings as safety backup bearings. These support the rotor and protect the pump in the event of a total disruption of magnetic suspension or a massive air inrush which overcomes the magnetic bearing stiffness. These high precision ball bearings are dry lubricated and are not in contact with the rotor during normal operation.
Optimized rotors The multistage pure bladed rotors in the UHV pumps provide the high vacuums required for clear beamlines on CD SEM machines, mass spectrometers and ion implanters. They provide optimum pumping performance with excellent light gas compression ratios.
Compound rotors The high throughput pumps incorporate a Holweck drag stage that increases the pumps throughput at low pressure.
Advanced series compound rotors The advanced series pumps have a redesigned compound rotor, the materials of manufacture have been improved to reduce the clearances within the pump, the rotors have an advanced 3D design and the Holweck stage has been redesigned to increase the throughput.
Corrosion resistant To ensure a high level of resistance to corrosion, the corrosion resistant (C) and high throughput (H-C) pumps have nickel coated rotors/stators and pump internals suitable for ion implantation and plasma etching. Further enhanced levels of protection are available on request.
Nitrogen purging The corrosion resistant (C) pumps and the high throughput (H-C) pumps have a nitrogen purge facility, a constant flow of nitrogen through the pump dilutes corrosive gases minimizing their damage to the pumps motor and sensor coils.
TMS system The BOC Edwards Temperature Management System is available on a wide range of turbo pumps. It is designed to optimize the temperature within the pump, dramatically reducing the particle condensation within. This will not only considerably enhance the performance of the pump under harsh process conditions, but also increase its operational life.
APPLICATIONS
Semiconductor fabrication STP turbomolecular pumps are the number one choice for the world's leading semiconductor etch and implant manufacturers. The pumps are installed on the harshest applications (for example, metal etch) and demonstrate exceptional levels of reliability.• Plasma etch (chlorine, fluorine and bromine chemistries) for metal
(aluminum), tungsten and dielectric (oxide) and polysilicon• Electron cyclotron resonance (ECR) etch• Film deposition CVD, PECVD, ECRCVD, MOCVD• Sputtering• Ion implantation source, beam line pumping end station• MBE• Diffusion• Photo resist stripping• Crystal/epitaxial growth• Wafer inspection• Load lock chambers
Scientific applications STP pumps are used extensively in the world’s foremost research and development institutes. The pumps satisfy stringent performance criteria and reliability expectations. They are also used in the following applications:• Scientific instruments: surface analysis, mass spectrometry, electron
microscopy• High energy physics: beam lines, accelerators• Radioactive applications: fusion systems, cyclotrons
1 50 100
18
28 44
2
10 amp/div-12
Residual gas analysis
0 200 400 600 800 1000Hz
5x10
μm
-3
Vibration analysis STP300 displacement/frequency
N2
TMSC
O
For further information contact BOC Edwards
2PAGE
30
DATA SUMMARY STP MAGNETICALLY LEVITATED TURBOMOLECULAR PUMPSSTP magnetically levitated turbomolecular pumps and accessoriesturbomolecular pumps
STP maglev turbomolecular pumps and accessories
Pump STP-iX455 STP301/STP301C STP-L301/STP-L301C
STP603/STP603C STP1003/STP1003C
STPH301C
Catalog page 2-32 2-34 2-36 2-38 2-40 2-42
Pumping speed l s-1
N2 300/450 300 260 650 1000 300H2 300/460 300 290 550 800 200
Inlet flange ISO100K/DN100CFISO160K/
DN1600CF
ISO100/DN100CF
ISO100/DN100CF
ISO160F/DN160CF
ISO200F/DN200CF
ISO100K/DN100CF
Ultimate pressure with bake out heating Pa (Torr)
ISO 10-8 DN Flange 6.5 x 10-6 (5 x 10-8) 10-6 (108) order 10-7 (10-9) order 10-7 (10-9) order 10-7 (10-9) orderCF (not C version) 10-6 ISO Flange 10-8 (10-10) order 10-8 (10-10) order 10-8 (10-10) orderCF (C version only) 10-7 (10-9) order 6.5 x 10-6 (5 x 10-8) 6.5 x 10-6 (5 x 10-8)
Rated speed 55,000 48,000 48,000 35,000 35,000 48,000Control unit – SCU-301/451 SCU-301/451 SCU-750 SCU-750 SCU-750
Pump STPH451C STPA803C STPA1303C STPA1603C" STPA2203C STP-XA2703C STP-XA3203C
Catalog page 2-44 2-46 2-48 2-50 2-52 2-54 2-56
Pumping speed l s-1
N2 450 800 1300 1600 2200 2650 3200H2 300 520 800 1200 1700 2050 2300
Inlet flange ISO160K/DN160CF
ISO160F/DN160CF
ISO200F/DN200CF
ISO200F/DN200CF
ISO250F/ICF305
ISO250F/VG250
ISO320F/VG300
Ultimate pressure with bake out heating Pa (Torr)
ISO 10-7 (10-9) order
10-7 (10-9) order
10-7 (10-9) order
10-7 10-6 (10-8) order
10-7 order 10-7 order
CF (not C version)CF (C version only)
Rated speed 48,000 32,500 32,500 36,500 27,000 27,500 27,500Control unit SCU-750 SCU-750 SCU-750 SCU-750 SCU-1500 SCU-1500 SCU-1500
Shop online at www.bocedwards.com
2PAGE
31
TU
RB
OM
OL
EC
UL
AR
PU
MP
SDATA SUMMARY STP MAGNETICALLY LEVITATED TURBOMOLECULAR PUMPS
Control unit SCU750 control unit SCU-1500 control unit
Catalog page 2-58 2-58
Magnetic bearing control system
Digital control Digital control
Input voltage AC100 – 100-120 ±10% V a.c./AC200
200-240 ± 10% V a.c.
200 to 240±10% V a.c.
Power consumption VAWithout TMS Max 850 1500With TMS Max 1200 2100
Input frequency Hz 50/60±2 50/60±2Leak current mA Max 3.5 Max 3.5Input phase – Single PhaseMain breaker rated current A 10 15Motor driving system Three phase DC
brush less motor driver
Three phase DC brush less motor
driverAllowable ambient temperature °C 0 – 40 0 to 40Storage temperature °C -25 – 55 -25 to 55Mass kg 8.5 12TMS control unit Built in Built inSerial communication function
RS232 Standard StandardRS485 Standard Standard
Panel display LCD (20 characters, 2 lines) –
Shop online at www.bocedwards.com
2PAGE
32
STP-iX455 TURBOMOLECULAR PUMP
The STP-iX455 turbomolecular pump with integrated controller employs an innovative magnetic bearing system.
The new magnetic bearing system reduces vibration by 50% in comparison to existing products. This pump is well suited for use with electron microscopes, metrology systems, and for lithography systems where low vibration is critical to the application. It is also suitable for a wide range of PVD, ALD, Etch and curing processes. STP-iX455 operates on 48 V d.c. eliminating the need for a conventional rack-mounted control unit and connection cable. With numerous optional accessories available, an optimum configuration can be found for each application.
Features & benefitsInnovative New Magnetic Bearing System• New concept self-sensing MB technology enables significantly reduced
pump vibration and cuts down magnetic fields leakage• Digital 5-axis magnetic bearing control provides stability to external
vibration or impact
Compact Design• Integrated controller eliminates the bulky controller cable and
conventional rack mounted control unit• Operates with 48 V d.c. only• Ambient Cooling
(optional fan accessory for high gas throughput applications)
Low Vibration• AVR (Auto Vibration Reduction) minimizes the rotate system vibration
during acceleration• ABS (Auto Balancing System) equipped as standard
Reliability• Reliable 5 axis maglev technology• Warning and maintenance functions
Certifications• Conforms to international safety standards• CE marked, UL listed SEMI compliant
TECHNICAL DATA
Pumping speed (pumping speed vs inlet pressure)
Inlet flange size ISO100K/DN100CF
ISO160K/DN1600CF
Pumping speedN2 300 l s-1 450 l s-1
H2 300 l s-1 460 l s-1
Compression ratioN2 >108
H2 >1 x 104
Ultimate pressure DN Flange 10-8 order PaISO Flange 6.5 x 10-6 order Pa
Maximum working pressure 1.3 x 10-1 PaAllowable backing pressure 67 PaRated speed 55000 rpmStarting time <6 minMounting position Any orientationCooling Method Natural air cooling
(air cooling when baking and gas pumping)Lubricating oil Not necessaryBacking pump 240 l min-1
Leakage Magnetic FluxAxial direction <100 m GaussRadial direction <100 m Gauss
Ambient temperature range 0 to 40 ºCStorage temperature range -25 to 55 ºCWeight 15 kg 16 kg
STP-iX455 (450 l s-1)
N2
STP-iX455 (300 l s-1)
STP-iX455 (460 l s-1)
STP-iX455 (300 l s-1)
H2
Nitrogen
Hydrogen
NEW
Shop online at www.bocedwards.com
2PAGE
33
TU
RB
OM
OL
EC
UL
AR
PU
MP
SCompression ratio (compression ration CR vs backing pressure)
A Inlet port ISO100 C Power cable connector
B Inlet port ISO160 D Outlet port KF25
OPTIONAL ACCESSORY
Optional accessories
A number of accessories are available to meet optimum configuration in each application.
Power Supply Unit iPS-240
This is a power supply unit for operation from 100-200 V a.c. power source. • STP-Link communication port on the front panel • Possible to dock with the iDT-001 display unit and becomes an
integrated power supply with an LCD display.
TECHNICAL DATA
Display Unit iDT-001
This is a handy terminal display and manual control unit for visual feedback of performance and for direct control of the pump.• A plug-and-play unit connecting with the STP-iX455 or iPS-240 • Docking connection available with the iPS-240 • Displays operational status on the LCD panel
STP-iX455
10
101010
3
10-3 -2
10
410
105
10
6
CR
7
10-1 0
8
10 10-1 0
10101 2
mbar
Pa
H2
He
A
B
4 x M12 x 25
D
C
Ø160
108
Ø180
190
30° 30°
165
255
12
120
12
Ø130
Ø180
197
235
237
266 16
7
205
207
236
177
57
87
Input voltage 100-240 V a.c.Input power Max 300 VAInput frequency 50/60 HzInrush current <40 ALeakage current <1.0 mAOutput voltage 48±2 V d.c.Rated output current 5 AOver-voltage protection 55.2-64.8 V d.c.Over-current protection Output fuse (7A, Fast-blow type)Withstand voltage Between input and FG: 1500 V a.c.,
1 min between input and output: 2300 V a.c., 1 min (current limit: 20 A)
Allowable ambient temperature 0 to 40 ºCStorage temperature -20 to 55 ºCMass 3 kg
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP-iX455 PumpISO100K PT640Z010ISO160K PT640Z020DN100CF PT640Z050DN160CF PT640Z060
iPS-240 Power Supply PT64W0Z00STP-iX455-iPS-240 interconnection cable
5 m PT64Y0B2010 m PT64Y0B3015 m PT64Y0B4020 m PT64Y0B50
Power supply cable for iPS-2403 m PT64Y0A105 m PT64Y0A20
iDT-001 Display Unit PT64W1Z00
NEW
Shop online at www.bocedwards.com
2PAGE
34
STP301/STP301C TURBOMOLECULAR PUMP
BOC Edwards STP301 and corrosion resistant STP-301C are for use in electron microscopes and semiconductor applications. BOC Edwards rotor technology gives class-leading performance for maximum process flexibility. The STP301 has been approved for use by major equipment manufacturers in the scientific instrument, semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Maximized process flexibility• Oil free• Low vibration• High reliability• Maintenance free
Advanced controller design• Auto tuning• Self diagnostic functions• d.c. motor drive• Battery-free operation
Compact design• Small footprint• Half rack controller
TECHNICAL DATA
Pumping speed (pumping speed vs inlet pressure)
Compression ratio (compression ration CR vs backing pressure)
Inlet flange ISO100 / DN100CFOutlet port KF25Purge port KF10 (C version only)Pumping speed
N2 300 l s-1
H2 300 l s-1
Compression ratioN2 >108
H2 >2 x 104
Ultimate pressure with bake out heatingISO inlet flange 6.5 x 10-6 (5 x 10-8) Pa (Torr)CF inlet flange (not C version) 10-8 order (10-10 order) Pa
(Torr)CF inlet flange (C version only) 10-7 order (10-9 order) Pa (Torr)
Maximum allowable inlet pressureAmbient cooled 0.066 (5 x 10-4) Pa (Torr)
Maximum continuous outlet pressureAmbient cooled 13 (0.1) Pa (Torr)
Rated speed 48000 rpmStarting time 3 minMaximum inlet flange temperature 120 ºCInput voltage 100 to 120 V a.c. (±10%) or
200 to 240 V a.c. (±10%)Power consumption
Start up 0.55 kVAWeight
Pump 11 kgController 7 kg
STP301
H2
STP301
N2
Nitrogen
Hydrogen
STP301
10
101010
3
10-3 -2
10
410
105
10
6
CR
7
10-1 0
8
10 10-1 0
10101 2
mbar
Pa
H2
N2
He
Shop online at www.bocedwards.com
2PAGE
35
TU
RB
OM
OL
EC
UL
AR
PU
MP
SA Electrical connectors for control unit C Purge port (C version only)
B Outlet flange
Controller
99.5
A
45
8 x M8 x 16
C
Ø16
0
B
110
108
315
200
140
209.7
122.5
132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STP301
ISO100 inlet B74830020DN100CF inlet B74831010
STP301CISO100 inlet B74871010DN100CF inlet B74881010
Controller100-120 V 50/60 Hz PT21Z0Z00200-240 V 50/60 Hz PT21Z0Z04
Connection cables3 m B707000105 m B7070000012 m PT21Y0B08
Power cablesRing terminal 3 m B70700090Ring terminal 5 m B70700040European plug 3 m A50506010UK plug 3 m A50505010
OptionsWater cooling coil
Horizontal fitting RC1/4 B74801750Vibration isolator
ISO100 B58046000DN100CF B74834010
Shop online at www.bocedwards.com
2PAGE
36
STP-L301/STP-L301C TURBOMOLECULAR PUMP
BOC Edwards STP-L301(C) and corrosion resistant STP-L301(C) are for use in electron microscopes and semiconductor applications. BOC Edwards rotor technology gives class-leading performance for maximum process flexibility. The STP-L301(C) has been approved for use by major equipment manufacturers in the scientific instrument, semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Maximized process flexibility• Oil free• Low vibration• High reliability• Maintenance freeAdvanced controller design• Auto tuning• Self diagnostic functions• d.c. motor drive• Battery-free operationCompact design• Small footprint• Half rack controller
TECHNICAL DATA
Pumping speed (pumping speed vs inlet pressure)
Compression ratio (compression ration CR vs backing pressure)
Inlet flange ISO100 / DN100CFOutlet port KF25Purge port KF10 (C version only)Pumping speed
N2 260 l s-1
H2 290 l s-1
Compression ratioN2 >108
He 5 x 105
H2 2 x 104
Ultimate pressure with bake out heating 10-6 order(10-8 order) Pa (Torr)Maximum allowable inlet pressure
Ambient cooled 6.7 x 10-2 (5 x 10-4) Pa (Torr)Maximum continuous outlet pressure
Ambient cooled 13 (0.1) Pa (Torr)Rated speed 48000 rpmStarting time 3 minMaximum inlet flange temperature 120 ºCInput voltage 100 to 120 V a.c. (±10%) or
200 to 240 V a.c. (±10%)Power consumption
Start up 0.55 kVAWeight
Pump 13 kgController 7 kg
STP-L301
H2
STP-L301
N2
Nitrogen
Hydrogen
STP-L301
10
101010
3
10-3 -2
10
410
105
10
6
CR
7
10-1 0
8
10 10-1 0
10101 2
mbar
Pa
H2
N2
He
Shop online at www.bocedwards.com
2PAGE
37
TU
RB
OM
OL
EC
UL
AR
PU
MP
S
A Connector
B Outlet port
Controller
Ø130
20716
666
8
240
7383
3310
8
Ø115
Ø180
Ø128
99.5
Ø156
15°
20°
20°
A
8 x M8 x 16
M4 x 10
B25°
30°7.5°
Ø14
8.5
Ø130.2
Ø160
Ø160
15°
30°
45°
22.5°
22.5°11.25°
ISO100 ICF152 VG100
16 x Ø8
8 x Ø127.5°
ISO100
ICF152Ø152
Ø110Ø115
2155
VG100Ø185
Ø1153512
315
200
140
209.7
122.5
132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STP-L301
ISO100 inlet B75800090DN100CF inlet PT470Z000
STP-L301CISO100 inlet B75800010DN100CF inlet PT47AZ030
Controller100-120 V 50/60 Hz PT21Z0Z00200-240 V 50/60 Hz PT21Z0Z04
Connection cables3 m B707000105 m B7070000012 m PT21Y0B08
Power cablesRing terminal 3 m B70700090Ring terminal 5 m B70700040European plug 3 m A50506010UK plug 3 m A50505010
OptionsWater cooling coil
Horizontal fitting RC1/4 B74801750Vibration isolator
ISO100 B58046000DN100CF B74834010
Shop online at www.bocedwards.com
2PAGE
38
STP603/STP603C TURBOMOLECULAR PUMP
BOC Edwards STP603 and corrosion resistant STP603C are new turbomolecular pumps for use in the most advanced semiconductor applications. BOC Edwards rotor technology gives class-leading performance for maximum process flexibility. Both pumps have been approved for use by major equipment manufacturers in the semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Maximized process flexibility• Oil free• Low vibration• High reliability• Maintenance free• Harsh process compatible (C version)• Increased life
Advanced controller design• Auto tuning• Self diagnostic functions• d.c. motor drive• Battery-free operation
Compact design• Small footprint• Half rack controller
TECHNICAL DATA
Pumping speed (pumping speed vs inlet pressure)
Compression ratio (compression ration CR vs backing pressure)
Inlet flange ISO160F / DN160CFOutlet port KF40Purge port KF10 (C version only)Pumping speed
N2 650 l s-1
H2 550 l s-1
Compression ratioN2 >108
H2 >105
Ultimate pressure with bake out heatingISO inlet flange 10-7 (10-9) order Pa (Torr)CF inlet flange (not C version) 10-8 (10-10) order Pa (Torr)CF inlet flange (C version only) 6.5 x 10-6 (5 x 10-8) Pa (Torr)
Maximum continuous outlet pressure1 13 (0.1) Pa (Torr)Rated speed 35000 rpmStarting time 6 minMaximum inlet flange temperature 120 ºCInput voltage 100 to 120 V a.c. (±10%) or
200 to 240 V a.c. (±10%)Power consumption (continuous) 0.8 kVAWeight
Pump 31 kgController 9 kg
1 Water cooled
STP603
0
N2
STP603
0
H2
Nitrogen
Hydrogen
STP603
10
101010
3
10-3 -2
10
410
105
10
6
CR
7
10-1 0
8
10 10-1 0
10101 2
mbar
Pa
H2
N2
He
Shop online at www.bocedwards.com
2PAGE
39
TU
RB
OM
OL
EC
UL
AR
PU
MP
S
A Electrical connector
B Outlet port
C Purge port (C version only)
Controller
L type connector
A Polarizing groove
B Outlet port
C Polarizing boss
200
315
400
140
210
122.5132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STP603
ISO160F B72102010DN160CF PT390Z005
STP603CISO160F B72102020DN160CF PT39AZ002
Controller100 V-120 V/200-240 V 50/60 Hz RS232C PT56Z0Z00
Connection cablesStraight connector
3 m B751300505 m B7513002010 m B75130060
Power cablesRing terminal 5 m PT46Y0A01Ring terminal 10 m PT46Y0A10
OptionWater cooling coil
Horizontal fitting RC1/4 B72132020
C
C
B
A
C
180° 270°
0°
90°
C
Shop online at www.bocedwards.com
2PAGE
40
STP1003/STP1003C TURBOMOLECULAR PUMP
BOC Edwards STP1003 and corrosion resistant STP1003C are new turbomolecular pumps for use in the most advanced of semiconductor applications. BOC Edwards rotor technology gives class-leading performance for maximum process flexibility. Both pumps have been approved for use by major equipment manufacturers in the semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Maximized process flexibility• Oil free• Low vibration• High reliability• Maintenance free• Harsh process compatible (C version)• Increased life
Advanced controller design• Auto tuning• Self diagnostic functions• d.c. motor drive• Battery-free operation
Compact design• Small footprint• Half rack controller
TECHNICAL DATA
Pumping speed (pumping speed vs inlet pressure)
Compression ratio (compression ration CR vs backing pressure)
Inlet flange ISO200F / DN200CFOutlet port KF40Purge port KF10 (C version only)Pumping speed
N2 1000 l s-1
H2 800 l s-1
Compression ratioN2 >108
H2 >105
Ultimate pressure with bake out heatingISO inlet flange 10-7 (10-9) order Pa (Torr)CF inlet flange (not C version) 10-8 (10-10) order Pa (Torr)CF inlet flange (C version only) 6.5 x 10-6 (5 x 10-8) Pa (Torr)
Maximum continuous outlet pressure1 13 (0.1) Pa (Torr)Rated speed 35000 rpmStarting time 6 minMaximum inlet flange temperature 120 ºCInput voltage 100 to 120 V a.c. (±10%) or
200 to 240 V a.c. (±10%)Power consumption (continuous) 0.8 kVAWeight
Pump 31 kgController 9 kg
1 Water cooled
2 With cooling water, for bakeout
0
STP1003
H2
0
STP1003
N2
Nitrogen
Hydrogen
STP1003
10
101010
3
10-3 -2
10
410
105
10
6
CR
7
10-1 0
8
10 10-1 0
10101 2
mbar
Pa
H2
N2
He
Shop online at www.bocedwards.com
2PAGE
41
TU
RB
OM
OL
EC
UL
AR
PU
MP
S
A Electrical connector
B Outlet port
C Purge port (C version only)
Controller
L type connector
A Polarizing groove
B Outlet port
C Polarizing boss
Ø260
ISO200F
30˚�
297�
147.
5�
200
315
400
140
210
122.5132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STP1003
ISO200F PT390Z001DN200CF B72101040
STP1003CISO200F B72101030DN200CF PT39AZ003
Controller100 V-120 V/200-240 V 50/60 Hz RS232C PT56Z0Z00
Connection cablesStraight connector
3 m B751300505 m B7513002010 m B75130060
Power cablesRing terminal 5 m PT46Y0A01Ring terminal 10 m PT46Y0A10
OptionsWater cooling coil
Horizontal fitting RC1/4 B72132020Vibration Isolator
ISO200 B58061000
C
C
B
A
C
180° 270°
0°
90°
C
Shop online at www.bocedwards.com
2PAGE
42
STPH301C HIGH PERFORMANCE TURBOMOLECULAR PUMP
BOC Edwards high performance STPH301C turbomolecular pump has been designed for use in the harshest of semiconductor applications. The pump's field proven reliability and class-leading performance give maximum process flexibility. The STPH301C has been approved for use by major equipment manufacturers in the semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Higher gas throughput• Maximized process flexibility• Oil free• Low vibration• High reliability• Maintenance free• Harsh process compatible• Increased life
Advanced controller design• Auto tuning• Self diagnostic functions• d.c. motor drive• Battery-free operation
Compact design• Small footprint• Half rack controller
5 axis magnetic suspension system• Zero contamination• Low maintenance• Any orientation operation
TECHNICAL DATA
1 Ar 2 N2 3 He 4 H2
A Electrical connector D Cooling water out
B Outlet port E Cooling water in
C Purge port
Inlet flange ISO100K / DN100CFOutlet port KF40Purge port KF10Water cooling fitting PT1/4Pumping speed
N2 300 l s-1
H2 200 l s-1
Compression ratioN2 >108
H2 103
Ultimate pressure with bake out heating 10-7 (10-9) order Pa (Torr)Maximum continuous outlet pressure1 660 (5) Pa (Torr)Maximum Nitrogen throughput1 2500 sccmRated speed 48000 rpmStarting time 4 minMaximum inlet flange temperature 120 ºCInput voltage 100 to 120 V a.c. (±10%) or
200 to 240 V a.c. (±10%)Power consumption 0.6 kVA
WeightPump 15 kgController 9 kg
1 Water cooled
40
40
Ø130
Ø156
Ø180
211
255.
5
12
ISO100K
197
211
257
45
45
35 34
171
�160
115
111
A
D
EC
B
8 x M8 x 20
Shop online at www.bocedwards.com
2PAGE
43
TU
RB
OM
OL
EC
UL
AR
PU
MP
SL type connector
A Polarizing groove
B Outlet port
C Polarizing boss
Controller
C
C
B
A
C
180° 270°
0°
90°
C
200
315
400
140
210
122.5132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STPH301C
ISO100K inlet B71901010DN100CF inlet PT340Z004
Controller 100-120 V/200-240 V 50/60 Hz RS232C PT56Z0Z00
Connection cablesStraight connector
3 m B751300505 m B7513002010 m B75130060
Power cablesRing terminal 5 m PT46Y0A01Ring terminal 10 m PT46Y0A10
TMS system is available for this model. For a complete installation order an STP pump (TMS), a controller, a TMS connection cable kit, a connection cable, and power cable is required.STPH301CV (TMS)
ISO100F PT3416001DN100CF PT3416005
TMS connection cable kit5 m PT330V00010 m PT330V00115 m PT330V002
Shop online at www.bocedwards.com
2PAGE
44
STPH451C HIGH PERFORMANCE TURBOMOLECULAR PUMP
BOC Edwards high performance STPH451C turbomolecular pump has been designed for use in the harshest of semiconductor applications. The pump's proven reliability and class-leading performance give maximum process flexibility. The STPH451C has been approved for use by major equipment manufacturers in the semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Higher gas throughput• Maximized process flexibility• Oil free• Low vibration• High reliability• Maintenance free• Harsh process compatible• Increased life
Advanced controller design• Auto tuning• Self diagnostic functions• d.c. motor drive• Battery-free operation
Compact design• Small footprint• Half rack controller
5 axis magnetic suspension system• Zero contamination• Low maintenance• Any orientation operation
TECHNICAL DATA
1 Ar 2 N2 3 He 4 H2
A Electrical connector D Cooling water out
B Outlet port E Cooling water in
C Purge port
Inlet flange ISO160K / DN160CFOutlet port KF40Purge port KF10Water cooling fitting PT1/4Pumping speed
N2 450 l s-1
H2 300 l s-1
Compression ratioN2 >108
H2 103
Ultimate pressure with bake out heating 10-7 (10-9) order Pa (Torr)Maximum continuous outlet pressure1 660 (5) Pa (Torr)Maximum Nitrogen throughput1 2500 sccmRated speed 48000 rpmStarting time 4 minMaximum inlet flange temperature 120 ºCInput voltage 100 to 120 V a.c. (±10%) or
200 to 240 V a.c. (±10%)Power consumption 0.6 kVA
WeightPump 15 kgController 9 kg
1 Water cooled
40
40
Ø180
Ø156
Ø18018
8
227.
5
12
ISO160K
172
188
231.
5
45
45
35 34
171
�160
115
110.
7
A
D
E
C
B
8 x M8 X 20
Shop online at www.bocedwards.com
2PAGE
45
TU
RB
OM
OL
EC
UL
AR
PU
MP
SL type connector
A Polarizing groove
B Outlet port
C Polarizing boss
Controller
C
C
B
A
C
180° 270°
0°
90°
C
200
315
400
140
210
122.5132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STPH451C
ISO160K inlet B71901001DN160CF inlet PT340Z005
Controller100-120 V/200-240 V 50/60 Hz RS232C PT56Z0Z00
Connection cablesStraight connector
3 m B751300505 m B7513002010 m B75130060
Power cablesRing terminal 5 m PT46Y0A01Ring terminal 10 m PT46Y0A10
TMS system is available for this model. For a complete installation order an STP pump (TMS), a controller, a TMS connection cable kit, a connection cable, and power cable is required.STPH451CV (TMS)
ISO160F PT3416007DN160CF PT3416006
TMS connection cable kit5 m PT330V00010 m PT330V00115 m PT330V002
Shop online at www.bocedwards.com
2PAGE
46
STPA803C "ADVANTAGE" TURBOMOLECULAR PUMP
BOC Edwards STPA803C is a new turbomolecular pump designed for use in semiconductor applications. BOC Edwards advanced rotor technology gives class-leading performance for maximum process flexibility. The STPA803C has been approved for use by major equipment manufacturers in the semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Maximized process flexibility• Oil free• Low vibration• High reliability• Maintenance free• Harsh process compatible • Increased life
Advanced controller design• Auto tuning• Self diagnostic functions• d.c. motor drive• Battery-free operation
Compact design• Small footprint• Half rack controller
TECHNICAL DATA
1 Ar 2 N2 3 H2
A Electrical connector
B Outlet port
C Purge port
Inlet flange ISO160F / DN160CFOutlet port KF40Purge port KF10Water cooling fitting PT1/4Pumping speed
N2 800 l s-1
H2 520 l s-1
Compression ratioN2 >108
H2 103
Ultimate pressure with bake out heating 10-7 (10-9) order Pa (Torr)Maximum continuous outlet pressure1 270 (2) Pa (Torr)Maximum Nitrogen throughput1 1500 sccmRated speed 32500 rpmStarting time 7 minMaximum inlet flange temperature 120 ºCInput voltage 200 – 240 V (±10%)Power consumption (continuous) 0.85 kVAWeight
Pump 39 kgController 9 kg
1Water cooled
Shop online at www.bocedwards.com
2PAGE
47
TU
RB
OM
OL
EC
UL
AR
PU
MP
SL type connector
A Polarizing groove
B Outlet port
C Polarizing boss
Controller
C
C
B
A
C
180° 270°
0°
90°
C
200
315
400
140
210
122.5132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STPA803C
ISO160F inlet B71801000DN160CF inlet B71805010
Controller200-240 V 50 Hz/60 Hz with RS232C PT56Z0Z00
Connection cablesStraight connector
3 m B751300505 m B7513002010 m B75130060
Power cablesRing terminal 5 m PT46Y0A01Ring terminal 10 m PT46Y0A10
TMS system is available for this model. For a complete installation order an STP pump (TMS), a controller, a TMS connection cable kit, a connection cable, and power cable is required.STPA803CV (TMS)
ISO160F PT3626000DN160CF PT3626003
TMS connection cable kit5 m PT330V00010 m PT330V00115 m PT330V002
Shop online at www.bocedwards.com
2PAGE
48
STPA1303C "ADVANTAGE" TURBOMOLECULAR PUMP
BOC Edwards STPA1303C is a new turbomolecular pump designed for use in semiconductor applications. Advanced rotor technology gives class-leading performance for maximum process flexibility. The STPA1303C has been approved for use by major equipment manufacturers in the semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Higher gas throughput• Maximized process flexibility• Oil free• Low vibration• High reliability• Maintenance free• Harsh process compatible• Increased life
Advanced controller design• Auto tuning• Self diagnostic functions• d.c. motor drive• Battery-free operation
Compact design• Small footprint• Half rack controller
TECHNICAL DATA
1 Ar 2 N2 3 H2
A Electrical connector
B Outlet port
C Purge portInlet flange ISO200F / DN200CFOutlet port KF40Purge port KF10Water cooling fitting PT1/4Pumping speed
N2 1300 l s-1
H2 800 l s-1
Compression ratioN2 >108
H2 103
Ultimate pressure with bake out heating 10-7 (10-9) order Pa (Torr)Maximum continuous outlet pressure1 270 (2) Pa (Torr)Maximum Nitrogen throughput1 1500 sccmRated speed 32500 rpmStarting time 7 minMaximum inlet flange temperature 120 ºCInput voltage 200 – 240 V a.c. (±10%)Power consumption (continuous) 0.85 kVAWeight
Pump 39 kgController 9 kg
1 Water cooled
Shop online at www.bocedwards.com
2PAGE
49
TU
RB
OM
OL
EC
UL
AR
PU
MP
SL type connector
A Polarizing groove
B Outlet port
C Polarizing boss
Controller
C
C
B
A
C
180° 270°
0°
90°
C
200
315
400
140
210
122.5132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STPA1303C
ISO200F inlet B71802020DN200CF inlet B71803000
Controller200-240 V 50/60 Hz RS232C PT56Z0Z00
Connection cablesStraight connector
3 m B751300505 m B7513002010 m B75130060
Power cable Ring terminal 5 m PT46Y0A01Ring terminal 10 m PT46Y0A10
TMS system is available for this model. For a complete installation order an STP pump (TMS), a controller, a TMS connection cable kit, a connection cable, and power cable is required.STPA1303CV (TMS)
ISO200F PT3626005DN2000CF PT3626004
TMS connection cable kit5 m PT330V00010 m PT330V00115 m PT330V002
Shop online at www.bocedwards.com
2PAGE
50
STPA1603C TURBOMOLECULAR PUMP
The small and powerful BOC Edwards STPA1603C turbo-molecular pump has been designed using BOC Edwards advanced rotor technology. This provides high throughput, maximum reliability and class leading performance which is demanded by the latest generation of semiconductor processes. Its half rack controller and compact design provide considerable space saving, whilst its advanced deposition reduction system gives improved reliability and performance. The STPA1603C has been qualified on the latest 200 mm etch tools as well as on new generation 300 mm oxide etch processes.
Features & benefitsAdvanced Rotor Design• Increased performance• Higher gas throughput• High reliability• Maintenance free• Harsh process compatible
5 Axis Magnetic Suspension System• Zero contamination• Low vibration
Corrosion Resistant• Harsh process compatible• Increased life
Compact Construction• Small footprint• Half rack controller
Advanced Controller Design• Tuning free• Self diagnostic functions• d.c. motor drive• Battery-free operation
TECHNICAL DATA
1 N2 2 Ar 3 He 4 H2
A Electrical connector D Cooling water out
B Outlet port E Cooling water in
C Purge port
Inlet flange ISO200F / DN200CFOutlet port KF40Purge port KF16Water cooling fitting PT1/4Pumping speed
N2 1600 l s-1
H2 1200 l s-1
Compression ratioN2 >108
H2 >7 x 103
Ultimate pressure with bake out heating 10-7 PaMaximum allowable backing pressure 266 (2.0) Pa (Torr)Maximum nitrogen throughput 2500 sccmRated speed 36500 rpmStarting time 7 minMounting position Any
Water coolingFlow 2 l min-1
Temperature 5-25 ºCPressure 3 kgf / cm-2
Recommended purge gas flow 20 sccmInput voltage 200 – 240 V a.c. (±10%)Typical power consumption 0.85 kVAWeight
Pump 35 kgController 9 kg
307.
5
320 27
6.5
262
16
35
268.
5
Ø270
Ø210
Ø237
Ø285ISO200F
180
A
D
30°
147.
5
8 x M2 x 20
147
B
E
C
35
30°
°
Ø260
12 x Ø11
15
Shop online at www.bocedwards.com
2PAGE
51
TU
RB
OM
OL
EC
UL
AR
PU
MP
SL type connector
A Polarizing groove
B Outlet port
C Polarizing boss
Controller
C
C
B
A
C
180° 270°
0°
90°
C
200
315
400
140
210
122.5132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STPA1603C
ISO200F B75100010DN200CF B75100100
Controller200-240 V 50/60 Hz RS232C PT56Z0Z00
Connection cablesStraight connector
3 m B751300505 m B7513002010 m B75130060
Power cableRing terminal 5 m PT46Y0A01Ring terminal 10 m PT46Y0A10
TMS system is available for this model. For a complete installation order an STP pump (TMS), a controller, a TMS connection cable kit, a connection cable, and power cable is required.STPA1603CV (TMS)
ISO200F PT4616004DN2000CF PT4616005
TMS connection cable kit5 m PT461V00010 m PT461V00115 m PT461V002
Shop online at www.bocedwards.com
2PAGE
52
STPA2203C "ADVANTAGE" TURBOMOLECULAR PUMP
BOC Edwards STPA2203C is a new turbomolecular pump designed for use in semiconductor applications. It has advanced rotor technology that gives class-leading performance for maximum process flexibility. A new half rack controller gives additional space savings and incorporates d.c. drive technology for battery-free operation. The STPA2203C has been approved for use by major etch, ion implant and deposition equipment manufacturers in the semiconductor and magnetic media industries.
Features & benefitsAdvanced rotor technology• Higher gas throughput• Maximized process flexibility5 axis magnetic suspension system• Zero contamination• Low maintenanceCorrosion resistant• Harsh process compatible• Increased lifeCompact construction• Small footprint• Half rack controllerAdvanced controller design• Tuning free• Self diagnostic functions• d.c. motor drive• Battery-free operation
TECHNICAL DATA
Pumping speed (pumping speed vs inlet pressure)
Compression ratio (compression ration CR vs backing pressure)
Inlet flange ISO250F / ICF305Outlet port KF40Purge port KF10Water cooling fitting PT1/4Pumping speed
N2 2200 l s-1
H2 1700 l s-1
Compression ratioN2 >108
H2 2.5 x 104
Ultimate pressure 10-6 (10-8) order Pa (Torr)Maximum allowable backing pressure 400 (3) Pa (Torr)Maximum nitrogen throughput 1500 sccmRated speed 27000 rpmStarting time 7 minMounting position AnyWater cooling
Flow 2 l min-1
Temperature 5-25 ºCPressure 2.9 x 105 Pa 3 kgf/cm
Recommended purge gas flow 20 (3.4 x 10-2) sccmInput voltage 200 – 240 V a.c. (±10%)Typical power consumption 1.5 kVAWeight
Pump 61 kgController 12 kg
0
STPA2203C
H2
0
STPA2203C
N2
Nitrogen
Hydrogen
STPA2203C
101010
2
10
0 1
1
10
310
104
10
5
CR
6
10
2 310 10
-2 -1
1010
0mbar
Pa
H2
N2
He
Shop online at www.bocedwards.com
2PAGE
53
TU
RB
OM
OL
EC
UL
AR
PU
MP
S
A Electrical connector D Cooling water out
B Outlet port E Cooling water in
C Purge port F Temperature sensor connector
Controller
L type connector
A Polarizing grooveB Outlet portC Polarizing boss
500
200
150
209.7
122.5
132.5
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STPA2203C
ISO250F PT4V0Z002DN250CF PT4V0Z003
Controller200-240 V 50/60 Hz RS232C PT59Z0Z00
Connection cablesStraight connector
3 m B750300305 m B7503001010 m B75030040
Power cablesRing terminal 5 m B75030020Ring terminal 10 m PT35Y0A00
TMS system is available for this model. For a complete installation order an STP pump (TMS), a controller, a TMS connection cable kit, a connection cable, and power cable is required.STPA2203CV (TMS)
ISO250F PT4V66001DN250CF PT4V66002
TMS connection cable kit5 m PT351V00010 m PT351V00115 m PT351V002
C
C
B
A
C
180° 270°
0°
90°
C
Shop online at www.bocedwards.com
2PAGE
54
STP-XA2703C TURBOMOLECULAR PUMP
The STP-XA2703C turbo pump offers high performance in the process range of high vacuum to 2300 sccm process flow with enhanced throughput for all gases.
This pump is based on a new platform design offering features to improve thermal management, which enhances performance on harsh processes, increases the maximum process flow capability and reduces the effects of corrosion and deposition.
The outstanding performance is suited to both light and harsh applications, such as semiconductor etch, implant, lithography and LCD processes.
Features & benefitsAdvanced rotor design• Increased H2, N2 and Ar performance• Improved performance in the process pressure range of high vacuum to
2300 sccm• Maintenance free
5-axis magnetic suspension system• Zero contamination• Low vibration
Innovative torque management• Patended torque reduction mechanism
Optimized temperature management• High temperature TMS capability• Low deposition• Built-in cooling mechanism• Higher gas throughput heated and unheated• Optimized life• Harsh process compatible
Certifications• SEMI® compliant, CE Marked and UL Listed
TECHNICAL DATA
1 Ar 2 N2 3 H2
A Temperature Management System (TMS) sensor D Outlet port KF40
B TMS Heater* E Cooling water port Rc 1/4 ISO
C TMS Heater Cover* F Purge port KF10
* TMS spec only
Inlet flange ISO250F / VG250Pumping speed
N2 2650 l s-1
H2 2050 l s-1
Compression ratioN2 >108
H2 6 x 103
Ultimate pressure 10-7 order PaMaximum allowable backing pressure 266 PaMaximum allowable gas flow
N2 (water cooled only) 2300 (3.8) sccm (Pa m3/s)Ar (water cooled only) 1900 (3.2) sccm (Pa m3/s)
Rated speed 27500 rpmStarting time 8 minMounting position Any orientationWater cooling
Flow 3 l minTemperature 5-25 (41-77) °C (°F)Pressure 0.3 MPa
Recommended purge gas flow 50 (8.4 x 10-2) sccm (Pa m3/s)Input voltage 200 – 240 +/-10%Typical power consumption 1.5 kVAWeight
Pump 75 (165) kg (lb)Controller 12 (26.4) kg (lb)
1 2 3
0
0
ø235(9.3)
187 (7
.4)
55o45
o
22.5o
22.5o
22.5o
22.5o
20o
20o
187
(7.4
)
>359.5 (14.2)
M16 x 24
E
F
D
ØA
mm (inch)
PortFlangeØA*B*C*D*E*F*G*H*J
VG250
350 (13.8)15 (0.6)
454 (17.9)409 (16.1)
377.5 (14.9)319 (12.6)262 (10.3)
379.5 (14.9)387 (15.2)
ISO250F
335 (13.2)15 (0.6)
454 (17.9)409 (16.1)
377.5 (14.9)319 (12.6)262 (10.3)
379.5 (14.9)387 (15.2)
ICF305(DN250CF)
305 (12.0)28 (1.1)
459 (18.1)414 (16.3)383 (15.1)325 (12.8)267 (10.5)385 (15.2)393 (15.5)
*B
*C
*D
*E
*F
*G
*H *J
ø335 (13.2)
ø358 (14.1)
ø326 (12.8)
45
(1.8
)
M16 x 33
A
C
B
NEW
Shop online at www.bocedwards.com
2PAGE
55
TU
RB
OM
OL
EC
UL
AR
PU
MP
SController
L type connector
A Polarizing grooveB Outlet portC Polarizing boss
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STP-XA2703C
ISO250 PT660Z140VG250 PT660Z110DN250CF PT6610010
Controller200-240 V, 50/60 Hz with RS232C PT59Z0Z00
Connection cablesStraight connector
3 m B750300305 m B7503001010 m B75030040
Power cablesRing terminal 5 m B75030020Ring terminal 10 m PT35Y0A00
500
200
150
209.7
122.5
132.5
C
C
B
A
C
180° 270°
0°
90°
C
NEW
Shop online at www.bocedwards.com
2PAGE
56
STP-XA3203C TURBOMOLECULAR PUMP
The STP-XA3203C turbo pump offers high performance in the process range of high vacuum to 2300 sccm process flow with enhanced throughput for all gases.
This pump is based on a new platform design offering features to improve thermal management, which enhances performance on harsh processes, increases the maximum process flow capability and reduces the effects of corrosion and deposition.
The outstanding performance is suited to both light and harsh applications, such as semiconductor etch, implant, lithography and LCD processes.
Features & benefitsAdvanced rotor design• Increased H2, N2 and Ar performance• Improved performance in the process pressure range of high vacuum to
2300 sccm• Maintenance free
5-axis magnetic suspension system• Zero contamination• Low vibration
Innovative torque management• Patended torque reduction mechanism
Optimized temperature management• High temperature TMS capability• Low deposition• Built-in cooling mechanism• Higher gas throughput heated and unheated• Optimized life• Harsh process compatible
Certifications• SEMI® compliant, CE Marked and UL Listed
TECHNICAL DATA
1 Ar 2 N2 3 H2
A Temperature Management System (TMS) sensor D Outlet port KF40
B TMS Heater* E Cooling water port Rc 1/4 ISO
C TMS Heater Cover* F Purge port KF10
* TMS spec only
Inlet flange ISO320F / VG300Pumping speed
N2 3200 l s-1
H2 2300 l s-1
Compression ratioN2 >108
H2 6 x 103
Ultimate pressure 10-7 order PaMaximum allowable backing pressure 266 PaMaximum allowable gas flow
N2 (water cooled only) 2300 (3.8) sccm (Pa m3/s)Ar (water cooled only) 1900 (3.2) sccm (Pa m3/s)
Rated speed 27500 rpmStarting time 8 minMounting position Any orientationWater cooling
Flow 3 l minTemperature 5-25 (41-77) °C (°F)Pressure 0.3 MPa
Recommended purge gas flow 50 (8.4 x 10-2) sccm (Pa m3/s)Input voltage 200 – 240 +/-10%Typical power consumption 1.5 kVAWeight
Pump 80 (176) kg (lb)Controller 12 (26.4) kg (lb)
1 2 3
0
0
ø235(9.3)
187 (7
.4)
55o45
o
22.5o
22.5o
22.5o
22.5o
20o
20o
187
(7.4
)
>359.5 (14.2)
M16 x 24
E
F
D
ØA
mm (inch)
PortFlangeØA*B*C*D*E*F*G*H*J
VG300
400 (15.8)18 (0.7)
415.5 (16.4)370.5 (14.6)
339 (13.3)280.5 (11.0)223.5 (8.8)341 (13.4)
348.5 (13.7)
ISO320F
425 (16.7)20 (0.8)
415.5 (16.4)370.5 (14.6)
339 (13.3)280.5 (11.0)223.5 (8.8)341 (13.4)
348.5 (13.7)
ICF356(DN320CF)
356 (14.0)28.5 (1.1)
454.5 (17.9)409.5 (16.1)378.5 (14.9)320.5 (12.6)262.5 (10.3)380.5 (15.0)388 (15.3)
*B
*C
*D
*E
*F
*G
*H *J
ø335 (13.2)
ø358 (14.1)
ø326 (12.8)
45
(1.8
)
M16 x 33
A
C
B
NEW
Shop online at www.bocedwards.com
2PAGE
57
TU
RB
OM
OL
EC
UL
AR
PU
MP
SController
L type connector
A Polarizing grooveB Outlet portC Polarizing boss
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP pump is supplied with an inlet screen.For a complete installation order an STP pump, a controller, a connection cable and power cable from the information below.STP-XA3203C
ISO320F PT660Z050VG300 PT660Z150DN320CF PT660Z080
Controller200-240 V, 50/60 Hz with RS232C PT59Z0Z00
Connection cablesStraight connector
3 m B750300305 m B7503001010 m B75030040
Power cablesRing terminal 5 m B75030020Ring terminal 10 m PT35Y0A00
500
200
150
209.7
122.5
132.5
C
C
B
A
C
180° 270°
0°
90°
C
ORDERING INFORMATION
PRODUCT DESCRIPTION ORDERING NUMBER
STP451
STP451ISO160 inlet B74840030DN160CF inlet B74841010
STP451CISO160 inlet B74851010DN160CF inlet B74861010
Controller100-120 V 50/60 Hz PT21Z0Z00200-240 V 50/60 Hz PT21Z0Z04
Connection cables3 m B707000105 m B7070000012 m PT21Y0B08
Power cablesRing terminal 3 m B70700090Ring terminal 5 m B70700040European plug 3 m A50506010UK plug 3 m A50505010
OptionsWater cooling coil
Horizontal fitting RC1/4 B74801750Vibration isolator
ISO160 B58049000DN160CF B70652040
STP-L451
STP-L451ISO160K B75800100DN160CF B75801110
STP-L451CISO160K B75800040DN160CF PT47AZ020
Controller100-120 V 50/60 Hz PT21Z0Z00200-240 V 50/60 Hz PT21Z0Z04
Connection cables3 m B707000105 m B7070000012 m PT21Y0B08
Power cablesRing terminal 3 m B70700090Ring terminal 5 m B70700040European plug 3 m A50506010UK plug 3 m A50505010
OptionsWater cooling coil
Horizontal fitting RC1/4 B74801750Vibration isolator
ISO160 B58049000DN160CF B70652040
NEW
Shop online at www.bocedwards.com
2PAGE
58
STPA3503C
STPA3503CISO320F inlet PT480Z003DN320CF inlet PT480Z010
Controller200-240 V 50Hz/60Hz with RS232C PT59Z0Z00
Connection cablesStraight connector
3 m B750300305 m B7503001010 m B75030040
Power cablesRing terminal 5 m B75030020Ring terminal 10 m PT35Y0A00
TMS system is available for this model. For a complete installation order an STP pump (TMS), a controller, a TMS connection cable kit, a connection cable, and power cable is required.STPA3503CV (TMS)
ISO320F PT4866001TMS connection cable kit
5 m PT351V00010 m PT351V00115 m PT351V002
STPF2203C
STPF2203CVG250 inlet PT50-0Z-002ISO250F inlet CallDN250CF inlet Call
Controller200-240 V 50Hz/60Hz with RS232C PT59Z0Z00
Connection cablesStraight connector
3 m B750300305 m B7503001010 m B75030040
Power cablesRing terminal 5 m B75030020Ring terminal 10 m PT35Y0A00
ORDERING INFORMATION
SCU750
STP603/1003 series, STPH301/H451 series, STPA803/A1303 series, and STPA1603 series.SCU750
100-120 V/200-240 V RS232C PT56Z0Z00
SCU-1500
STP-A2203 series, STP-A2503/A3003 series, STP-A2803/A3503 series, STP-F2203 series, STP-XA2703/XA3203 series.SCU-1500
200-240 V RS232C PT59Z0Z00
ORDERING INFORMATION
Recommended