View
213
Download
0
Category
Preview:
Citation preview
7/18/2019 [003123]
http://slidepdf.com/reader/full/003123 1/4
Backup / Transfer
1. Manual Backup / Transfer of Backup from Hard Disk to Magnetic Tape
A magnetic tape (2400 f t) can store a CP Backup of appx. 30MB.Deactivate automatic dumping.
SYBUE;
Initiate backup.
SYBUP:FILE=RELFSW2;
Wait for the backup to be EXECUTED.
Mount a blank tape on an MT connected to SPG 0.
Scratch the tape.
INTSI:SPG=0,NODE=A,IO=MT-x,REPLACE; [x = 1 or 2]
Wait for the following result printout.
UNFORMATTED TAPE
ENTER VOLNUM= (,OWNER= )(,LEVEL= /EBCDIC) OR 'NO'
:
At the colon prompt, enter the following:
VOLNUM=RELVOL;
Load the volume.
INMCT:SPG=0;
INVOL:NODE=A,IO=MT-x; [x = 1 or 2]
END;
Release the terminal and wait for the result printout:
Initiate transfer of the dump to tape.
SYMTP:SPG=0,NODE=A,FILE1=RELFSW2,IO2=MT-x,DIR=OUT;
[x = 1 or 2]
Wait for the result printout.
No value should appear under `FAULTCODE'.
Unload the volume.
INMCT:SPG=0;
INVOE:NODE=A,IO=MT-x; [x = 1 or 2]
7/18/2019 [003123]
http://slidepdf.com/reader/full/003123 2/4
END;
Release the terminal and wait for the result printout:
Print the label.
SYBFP:FILE=RELFSW2;
Rotate the reload files.
SYTUC;
RELFSW2 will become RELFSW0.
RELFSW0 will become RELFSW1.
RELFSW1 will become RELFSW2.
Activate automatic dumping.
SYBUI:DISC;
2. Transfer of Backup from Magnetic Tape to Hard Disk
Mount the backup tape on an MT connected to SPG 0.
Load the volume.
INMCT:SPG=0;
INVOL:NODE=A,IO=MT-x; [x = 1 or 2]
END;
Release the terminal and wait for the result printout.
Initiate transfer of the backup to hard disk.
SYMTP:SPG=0,NODE=A,FILE1=RELFSW2,IO2=MT-x,DIR=IN;
[x = 1 or 2]
Wait for the result printout.
No value should appear under `FAULTCODE'.
Unload the volume.
INMCT:SPG=0;
INVOE:NODE=A,IO=MT-x; [x = 1 or 2]
END;
Release the terminal and wait for the result printout:
3. Manual Backup / Transfer of Backup from Hard Disk to Optical
Disk (if avail able)Deactivate automatic dumping.
7/18/2019 [003123]
http://slidepdf.com/reader/full/003123 3/4
SYBUE;
Initiate backup.
SYBUP:FILE=RELFSW2;
Wait for the backup to be EXECUTED.
Insert a optical disk into the OD-drive connected to SPG 0.
Format the Optical drive. (If not already formatted)
INMCT:SPG=0;
INMEI:IO=OD-1,NODE=B,FORMAT=APN,VOL=RELVOL;
END;
Wait for the result printout.(Takes about 40 min)
Load the volume.
INMCT:SPG=0;
INVOL:NODE=B,IO=OD-1;
END;
Release the terminal and wait for the result printout:
Initiate transfer of the dump to tape.
SYMTP:SPG=0,NODE=B,FILE1=RELFSW2,IO2=OD-1,DIR=OUT;
Wait for the result printout.
No value should appear under `FAULTCODE'.
Unload the volume.
INMCT:SPG=0;
INVOE:NODE=B,IO=OD-1;
END;
Release the terminal and wait for the result printout:
Print the label.
SYBFP:FILE=RELFSW2;
Rotate the reload files. Use C'SYTUC;
RELFSW2 will become RELFSW0.
RELFSW0 will become RELFSW1.
RELFSW1 will become RELFSW2.
Activate automatic dumping. Use C'SYBUI:DISC;
7/18/2019 [003123]
http://slidepdf.com/reader/full/003123 4/4
4. Transfer of Backup from Optical Drive to Hard Disk
Insert the Optical disk with the backup into the
Optical drive of SPG 0.
Load the volume.
INMCT:SPG=0;
INVOL:NODE=B,IO=OD-1;
END;
Release the terminal and wait for the result printout.
Initiate transfer of the backup to hard disk.
SYMTP:SPG=0,NODE=B,FILE1=RELFSW2,IO2=OD-1,DIR=IN;
Wait for the result printout.
No value should appear under `FAULTCODE'.
Unload the volume.
INMCT:SPG=0;
INVOE:NODE=B,IO=OD-1;
END;
Release the terminal and wait for the result printout:
5. Printing Information on Backup Files
Print information for one of the backup files.
SYBFP:FILE=RELFSWx; [x = 0, 1 or 2]
Recommended