View
2
Download
0
Category
Preview:
Citation preview
© 2010 The William Carter Company. All rights reserved.
1
CONGRATULATIONS on your purchase of quality furniture by child of mine ®, from the makers of carter's ® . Your nursery furniture is thoughtfully designed to fit comfortably into your lifestyle and should provide you with years of reliable service if properly assembled and maintained.
Please read these instructions completely before use of this product. Failure to follow these warnings and the assembly instructions could result in serious injury or death. Please save manual for future use as it contains important information.
Please call toll free 1. 888.443.9876, or visit www.childofmine.com if you have any questions about your child of mine ® furniture including missing parts or how to assemble.
Model #: 10860
My Nursery Crib & Changing Station
Component Assembly
C
Step 1
B
B
C
C
Optional Toddler Bed / Day Bed
Step 3
1. Place Left Side Panel (H) on a soft, clean surface to prevent scratching.
2. Attach Top Rail (J) and Front Base Rail (L) to Left Side Panel (H) using 2pcs Curve Washers(6) and 2pcs Bolts (4). Tighten with Allen Key (14).
3. Attach Back Base Rail (M) to Left Side Panel (H) using 1pc Wood Dowel (13), 2pcs CurveWashers (6) and 2pcs Bolts (4). Tighten with Allen key (14).
4. Insert the tenon of Front Middle Rail (K) into mortise on Left Side Panel (H).
M
(13) 1x
Step 4
1. Insert the tenon on Front Middle Rail (K) into mortise on Right Side Panel (I).
2. Attach Back Base Rail (M) to Right Side Panel (I) using 1pc Wood Dowel (13), 2pcs CurveWashers (6) and 2pcs Bolts (4). Tighten with Allen key (14).
3. Attach the Top Rail (J), Front Base Rail (L) to Right Side Panel (I) using 2pcs Curve Washers(6) and 2pcs Bolts (4). Tighten with Allen key (14).
JK L
M
Step 5
1. Turn the assembled parts upright.
2. Attach Shelf (N) to Left Side Panel (H) and Right Side Panel (I) using 4pcs Bolts (3). Tightenwith Allen key (14).
Step 6
1. Attach the second Top Rail (J) to Left Side Panel (H) and Right Side Panel (I) using 2pcsCurve Washers (6) and 2pcs Bolts (4). Tighten with Allen Key (14).
F
1. Screw 2pcs Cam Studs (9) into the pre-drilled holes of Topper Side Rail (F) using PhilipheadScrew Driver (not provided). Turn clockwise until tight.
2. Insert 2pcs Wood Dowels (13) into pre-drilled holes on Topper Back Rail (E). Attach TopperBack Rail (E) to Topper Side Rail (F) using 1pc Cam Lock (8), rotate Cam Lock (8) 1/2 turnclockwise.
3. Insert 2pcs Wood Dowels (13) into pre-drilled holes on Topper Front Rail (D). Attach TopperFront Rail (D) to Topper Side Rail (F) using 1pc Cam Lock (8), rotate Cam Lock (8) 1/2 turnclockwise.
4. Repeat the same process to attach another Topper Side Rail (F) to Topper Front Rail (D)and Topper Back Rail (E).
Step 7
Step 8
D
1. Attach Top Panel (G) to assembled Topper Frame using 2pcs Bolts (3). Tighten with Allen key(14).
Step 9
1. Attach Topper Frame to assembled parts using 4pcs Bolts (5). Tighten with Allen Key (14).
Step 10
1. Attach Back Panel (O) using 10pcs Screws (11). Tighten with Philliphead screw driver (notprovided).
Step 11
1. Attach Drawer Left Side (Q) to Drawer Front (P) using 2pcs Wood Screws (12).
2. Repeat the same process to attach Drawer Right Side (R) to Drawer Front (P).
3. Slide Drawer Bottom (T) into grooves of panels.
4. Attach Drawer Back (S) to assembled parts using 4pcs Wood Screw (12).
5. Attach 2pcs Knobs (7) to Drawer Front (P) using 2pcs Screws (10).
6. Repeat above steps for second and third lower drawers.
1. Insert drawers into changing station by aligning the groove on the Drawer Sides to therunners located on the Left and Right Side Panels (H) and (I). Make sure left and rightsides of drawer box are aligned with the gliders located on the left and right side panels.
2. The drawer should open and close easily with little effort. If not, remove the drawer slowlyand repeat from step Above.
3. To remove the drawer: Press the plastic stopper on the Drawer Sides inward at the sametime then slightly pull the drawer out.
Step 12
Recommended